Related
My Moto X now refuses to boot. With stock recovery it'll get past the bootloader, then blink an image of a dead android with the message "Error" briefly, and keep doing so every ~10 seconds. If I flash TWRP, any attempt to boot takes me to TWRP, with log messages reading "unable to mount..." for a bunch of partitions (/data, /cache, storage, etc.)
Can I recover my device?
The short sequence of events: I rooted my phone (T-Mobile phone, unlocked it via Motorola's website) and installed TWRP. Later I tried to accept the 4.4.2 OTA update, but the phone wouldn't take the update, because TWRP. Flashed stock recovery tried again, got stuck in bootloop. Tried flashing back the 4.4 / 140.44.3 images from here, now I'm stuck with a blinking error message.
I see there are a bunch of image files bundled into the 4.4.2 / 161.44.25 update - would flashing those do any good?
What version is your bootloader?
Steve-x said:
What version is your bootloader?
Click to expand...
Click to collapse
Version 30.B2.
OK, you still have the 4.4 bootloader so you should have no problem flashing the full tmobile/retail/dev edition build of firmware. I'd perform a full flash with rsdlite or with fastboot using all of the commands in the xml file in the same order. Do not skip any files or bypass any files if there are errors.
This will reset your phone and wipe all content!
Did you attempt to clear dalvik and cache, I believe you can do it through fastboot
Fast boot erase cache should work . its trying to flash the it's ,so you need to delete the cache where the ota file downloaded to
Sent on my Gummy running Lenoto X
so here is abit more help here are the full firmware links
T-Mobile 4.4
http://sbf.droid-developers.org/download.php?device=0&file=2
that is the file you need to flash with RSD Lite or Fastboot and it should get you 100% back up and running.
But then if you want to go to 4.4.2 after you flash the firmware before you add anything or install TWRP just update the phone to 4.4.2 then install the custom recovery and SuperSU.
Steve-x said:
OK, you still have the 4.4 bootloader so you should have no problem flashing the full tmobile/retail/dev edition build of firmware. I'd perform a full flash with rsdlite or with fastboot using all of the commands in the xml file in the same order. Do not skip any files or bypass any files if there are errors.
This will reset your phone and wipe all content!
Click to expand...
Click to collapse
I have tried both RSD Lite, and applying all of the commands from the XML file manually, following the directions from here. Both ways, I still get the blinking error message
The "can't mount..." log messages I get if I flash back to TWRP suggest it could be some sort of partitioning problem, but I'm not sure how to diagnose that.
And the flashing of all files completes successfully?
Steve-x said:
And the flashing of all files completes successfully?
Click to expand...
Click to collapse
I could have sworn that I wasn't getting any errors previously. Now, however, after trying to flash system.img (making sure to use mfastboot, of course), I get an error on the phone, "sp space is not enough". Not sure what it means, and Googling around doesn't turn up any answers.
dray_jr said:
so here is abit more help here are the full firmware links
T-Mobile 4.4
http://sbf.droid-developers.org/download.php?device=0&file=2
Click to expand...
Click to collapse
Yep, that's exactly what I flashed. Made sure the md5sum matched my download and everything.
flashallthetime said:
Did you attempt to clear dalvik and cache, I believe you can do it through fastboot
Click to expand...
Click to collapse
Yep, cleared the cache, no luck
Ouch, it does kind of sound like the partition table got damaged. I suppose you could try "fastboot erase system" and then try to flash the system partition again.
So I guess more warnings into my noobs guide to accept an ota thread
Maybe I should put a notice not to accept the ota and only flash your carriers sbf firmware when available?
Sent on my Gummy running Lenoto X
Steve-x said:
Ouch, it does kind of sound like the partition table got damaged. I suppose you could try "fastboot erase system" and then try to flash the system partition again.
Click to expand...
Click to collapse
Code:
C:\Users\spiffytech\Documents\sdk\platform-tools>fastboot erase system
(bootloader) Variable not supported!
erasing 'system'...
(bootloader) Permission denied
FAILED (remote failure)
finished. total time: 0.101s
Well, that was very weird. In the bootloader I scrolled through the menu and accidentally selected "Factory". No idea what that's supposed to do, but now my phone boots again! I'm going to really, really, hope I don't break it again...
I want to try the 4.4.2 update now, but given I'm not really sure why my device works again I'm scared to.
spiffytech said:
Well, that was very weird. In the bootloader I scrolled through the menu and accidentally selected "Factory". No idea what that's supposed to do, but now my phone boots again! I'm going to really, really, hope I don't break it again...
I want to try the 4.4.2 update now, but given I'm not really sure why my device works again I'm scared to.
Click to expand...
Click to collapse
Good for you, I would wait for the sbf firmware to be available to flash, seems to me a safer way of getting the update
Sent on my Gummy running Lenoto X
flashallthetime said:
Good for you, I would wait for the sbf firmware to be available to flash, seems to me a safer way of getting the update
Sent on my Gummy running Lenoto X
Click to expand...
Click to collapse
I'll go with that plan What is it that makes flashing from sbf safer?
So if you perform a full factory reset the phone will boot up normally now? If that is the case then I don't see any problem with accepting the OTA to 4.4.2.
Help PLZ
I had the exact same problem as OP, took the same course of action, and got a successful boot. I do some minimal stuff, check if everything is working, turn on dev mode, etc. I put in my wifi password.
I wanted to check if my bootloader was back to stock, so I turned off my device, and then tried to power on. Pressing the power button does nothing.
So I get into fastboot, and select factory (reset) again. It boots up, but it doesn't seem like it actually did a factory reset, because it automatically connected to my wifi..
Have you any idea what's going on, and how perhaps to solve this weird dilemna?
EDIT: I'm not sure if I actually did anything, but after a couple reboots it just started working normally. I installed the update to 4.4.2 and everything is smooth thus far.
Eventually the phone prompted me to apply the 4.4.2 update so often the phone was actually unusable - it'd go back to the "do you want to update?" screen as soon as I backed out of it. I was thus forced to apply it OTA. Fortunately, the update went through fine this time, and my phone continues to work fine
Thanks for your help, folks!
I got a message on my XT1053 Dev that there's a system update. (I'm running stock) I let it download, and then it wanted to reboot. Ok, but it came up in TWRP. I tried rebooting from TWRP every way, but it would not go into maintenance so it could flash the new firmware.
Now whenever I boot it normally, it comes up, and then immediately shuts down, I guess because it wants to upgrade.
What is wrong with this thing?
Quantumstate said:
I got a message on my XT1053 Dev that there's a system update. (I'm running stock) I let it download, and then it wanted to reboot. Ok, but it came up in TWRP. I tried rebooting from TWRP every way, but it would not go into maintenance so it could flash the new firmware.
Now whenever I boot it normally, it comes up, and then immediately shuts down, I guess because it wants to upgrade.
What is wrong with this thing?
Click to expand...
Click to collapse
You must be on stock recovery in order to OTA update. Try going into adb and flashing back to stock recovery and it should work.
Make sure you have mfastboot set up and working, if you need the file respond to this post and I can supply it for you.
Download the stock recovery from here (and make sure it's in your "android" folder)
Boot your phone into fastboot with
adb reboot bootloader
Click to expand...
Click to collapse
-OR-
While the phone is off, hold the PWR button and the Volume Down buttons at the same time for ~5 seconds. Release the PWR button ONLY and continue holding Volume Down until you see the fastboot screen.
Next
Then in adb on your computer perform:
mfastboot flash recovery *filename*
mfastboot reboot
Click to expand...
Click to collapse
When it reboots into the OS it should try to install the update again, like you said it was doing. When it reboots it should update correctly via stock recovery.
Emphasis on should. I can't guaruntee this will work but this is based on my prior knowledge and experience. Good luck and report back with success/problems!
Quantumstate said:
I got a message on my XT1053 Dev that there's a system update. (I'm running stock) I let it download, and then it wanted to reboot. Ok, but it came up in TWRP. I tried rebooting from TWRP every way, but it would not go into maintenance so it could flash the new firmware.
Now whenever I boot it normally, it comes up, and then immediately shuts down, I guess because it wants to upgrade.
What is wrong with this thing?
Click to expand...
Click to collapse
There's nothing wrong with this thing....
All of the guides here exist for a reason. One responsibility you have once you have decided to root your device or install custom recovery, is that when a new OTA comes out, you must check back here at XDA to see what the procedure for installing it is.
All of the guides here tell you that you MUST have stock recovery in order to accept any updates.
Here's how you will fix it:
Boot into TWRP. Clear your cache. This will prevent the constant reboots.
Now, use fastboot to flash back the stock recovery. You will need to download the 4.4.2 SBF for your XT1053 from here: http://sbf.droid-developers.org/phone.php?device=0
Extract the archive. You only need one file: recovery.img
You should already have the android SDK installed since you unlocked your BL and flashed TWRP. Use fastboot to flash the stock recovery:
fastboot flash recovery recovery.img
Now you can accept the OTA from your phone. You may need to go to Settings > About Phone > System Updates and re-download it.
The OTA should now successfully install (assuming you aren't using Xposed or made any other modifications).
Now, you can flash TWRP recovery back. Let us know how it works out for you...
Thanks, but the update was unsuccessful.
I seem to remember that the update checks existing files, and if one has the wrong CRC it fails. Well I'm stock but rooted. It is a develoepr's phone and there is no developer's image on those sites.
Quantumstate said:
Thanks, but the update was unsuccessful.
I seem to remember that the update checks existing files, and if one has the wrong CRC it fails. Well I'm stock but rooted. It is a develoepr's phone and there is no developer's image on those sites.
Click to expand...
Click to collapse
The GSM Developer edition uses the SAME exact software as the T-Mobile version. The T-Mobile variant has zero bloat, and no carrier branding. The only difference between the two is that you don't lose your warranty when you unlock the GSM Dev edition.
You're looking for the XT1053 T-Mobile SBF
http://sbf.droid-developers.org/phone.php?device=0
Quantumstate said:
Thanks, but the update was unsuccessful.
I seem to remember that the update checks existing files, and if one has the wrong CRC it fails. Well I'm stock but rooted. It is a develoepr's phone and there is no developer's image on those sites.
Click to expand...
Click to collapse
I always seem to have something in /system that messes with the ota update. In addition to flashing stock recovery to replace twrp, I also flash system.img (with mfastboot only) from the same sbf as you get the recovery.img. Then the ota goes through without a hitch.
Still Errors at the robot with spinning diamond heart, even with TMO_RETAIL_XT1053_4.4.2-KXA20.16-1.25_MR3_CFC.xml/recovery.img.
Looking around it seems that here are some rules. I think I'm violating #2: "Inside the OTA is a manifest file. It contains a list of files and their check sums it expects to be on your phone. If the files are missing, or the check sum for a particular file doesn't match (because you've replaced or altered the file), the OTA will fall." I've removed most of the G**gle junk since I don't trust them.
So if this is what they require, Hell with them. If it were possible to put multiboot on the Moto X I would have done it a long time ago. Maybe I can apply this OTA update in some other way? Without going through their rinky-dink tests?
Quantumstate said:
Still Errors at the robot with spinning diamond heart, even with TMO_RETAIL_XT1053_4.4.2-KXA20.16-1.25_MR3_CFC.xml/recovery.img.
Looking around it seems that here are some rules. I think I'm violating #2: "Inside the OTA is a manifest file. It contains a list of files and their check sums it expects to be on your phone. If the files are missing, or the check sum for a particular file doesn't match (because you've replaced or altered the file), the OTA will fall." I've removed most of the G**gle junk since I don't trust them.
So if this is what they require, Hell with them. If it were possible to put multiboot on the Moto X I would have done it a long time ago. Maybe I can apply this OTA update in some other way? Without going through their rinky-dink tests?
Click to expand...
Click to collapse
You are correct on the manifest.
Instead, just flash the entire stock SBF (TMO_RETAIL_XT1053_4.4.2-KXA20.16-1.25). The manual method is easiest.
Or you could just flash the system.img as the earlier poster suggested.
This will revert to stock, and you will have to reinstall your apps, but the OTA WILL work afterwards. You really should consider just 'freezing' the google apps instead of removing them this time...
The only other way you will be able to install the OTA is to put all the gapps back on...but I doubt you made a backup, right?
mfastboot flash system system.img
that should be all you need (beside stock recovery, of course). Then take the update, and finally do whatever mods you want remembering that you will HAVE to un-do the mods to be able to accept future OTAs without returning to 100% stock again.
Good Luck
Flashing system.img will not require you to reinstall your downloaded apps, just apps you installed as system apps via root access. Downloaded apps are in the /data/app partition that is not affected by a system.img flash.
I finally went this route. I'm not putting up with their OTA requirements; I'll get the upgrade without them. Although, that 4.3 sure has alot of G**gle and Motorola bloatware to remove.
With Xposed, GravityBox (and other modules) I now have the flexibility I was looking for.
Now all I need is a better dialer than the crappy G**gle one, and secure SMS.
My nexus 6 is unlocked and is running stock 5.0.1, rooted. . It has twrp and is decrypted.
I tried to sideload the 5.1 ota but it doesnt work.
I tried flashing the new 5.1 factory image but that doesnt work.
I'm tired of all this now, I just want my phone running stock 5.1 , locked , encrypted ,unrooted so I can just get ota next time from Google whenever they send it out.
Any guidance on what I need to do would be appreciated.
Use Wug's Nexus Root Toolkit :good:
Edit : Now I'm currently "Optimising app..." loop.
I tried using tge NRT to flash it back to stock but it didn't work.
I would first make a TWRP backup, then I would flash the boot image (decrypted if you want and make sure its the new one), system, radio and then reboot. I flashed everything fine while keeping twrp on my phone but I didn't like not having a custom ROM plus it was a little laggy so I restored a TWRP backup. My phone did bootloop for a while but eventually it booted 5.1. I would be careful since 5.1 seems to be having some issues in general.
http://forum.xda-developers.com/nex...gs-nexus-root-toolkit-v1-9-8-t2947452/page101
Quote:
Originally Posted by baudi11
Same thing happened to me. Here's what I did.
1. Press and hold power, volume up, and volume down. Keep holding them down until the phone boots into bootloader mode.
2. Go back to the toolkit and click the radio button labeled "Soft bricked/bootloop"
3. Click "Flash stock plus unroot"
4. Check all the boxes under "Settings", including "Post-flash factory reset" then click OK.
5. Follow the toolkit instructions from there.
This got me out of the bootloop, successfully installed 5.1, and kept all my apps and settings. Good luck.
Click to expand...
Click to collapse
It worked for me after that. Now I'm booted in 5.1
When I try to flash the factory images directly from Google I get the following errors even though the MD5 checks out.
archive does not contain 'boot.sig'
archive does not contain 'recovery.sig'
failed to allocate 1778070480 bytes
error: update package missing system.img
Press any key to exit...
celeriL said:
http://forum.xda-developers.com/nex...gs-nexus-root-toolkit-v1-9-8-t2947452/page101
It worked for me after that. Now I'm booted in 5.1
Click to expand...
Click to collapse
Thanks so much! This worked perfectly. Exactly what I needed. The past couple days have been so annoying but now it's over. Thanks again!
Giuseppe1010 said:
Thanks so much! This worked perfectly. Exactly what I needed. The past couple days have been so annoying but now it's over. Thanks again!
Click to expand...
Click to collapse
Glad to help!
You also could have extracted the zip and manually flashed the images ing fastboot
fastboot flash recovery recovery.img
fastboot flash system system.img
Etc
rootSU said:
You also could have extracted the zip and manually flashed the images ing fastboot
fastboot flash recovery recovery.img
fastboot flash system system.img
Etc
Click to expand...
Click to collapse
HaHaa. Tried and true. Always works.
prdog1 said:
HaHaa. Tried and true. Always works.
Click to expand...
Click to collapse
rootSU said:
You also could have extracted the zip and manually flashed the images ing fastboot
fastboot flash recovery recovery.img
fastboot flash system system.img
Etc
Click to expand...
Click to collapse
I agree that always works without fail and is much easier than a tool kit. I don't like tool kits because people need to learn the correct way to flash things before using one because its better to understand what you are flashing should there be an error.
Pilz said:
I agree that always works without fail and is much easier than a tool kit. I don't like tool kits because people need to learn the correct way to flash things before using one because its better to understand what you are flashing should there be an error.
Click to expand...
Click to collapse
I totally agree. Have done successful manual flash when tool kits failed. Seen on Nexus 6 already.Saved my soft brick with manual flash when tool kit failed.
Pilz said:
I agree that always works without fail and is much easier than a tool kit. I don't like tool kits because people need to learn the correct way to flash things before using one because its better to understand what you are flashing should there be an error.
Click to expand...
Click to collapse
I don't have anything against toolkits on some devices, so long as it is not used as a shortcut to learning the basics. That said, on a nexus, I don't really see any need to be honest.
rootSU said:
I don't have anything against toolkits on some devices, so long as it is not used as a shortcut to learning the basics. That said, on a nexus, I don't really see any need to be honest.
Click to expand...
Click to collapse
Thats how I feel because its so easy my wife could do it and she doesn't know anything about flashing. Toolkits are good for non Nexus devices, I just don't see a point when we need to learn things the correct way first.
I hope the bugs get sorted out so people don't hard brick their phones anyone
rootSU said:
You also could have extracted the zip and manually flashed the images ing fastboot
fastboot flash recovery recovery.img
fastboot flash system system.img
Etc
Click to expand...
Click to collapse
Im a complete fastboot novice since this is my first nexus device (always had samsung phones up until now) and although I managed to root and unlock the boot loader I want to make sure I learn all the basics including flashing (side loading?) subsequent updates.
So Im currently rooted, unlocked bootloader on a 5.01. custom rom. How would I go about flashing the 5.1 update manually?
Im assuming that once I extract the update zip file I will find all the images that need to be flashed....what order do i do them in? How do I take into account the boot loader locking issue people have been facing that results in a bricked device?
Thanks in advance.
EDIT: I found this thread which outlines what I need to do http://forum.xda-developers.com/nexus-6/general/using-image-to-update-nexus-6-data-loss-t3053158
I only have two question now:
1. Im assuming the system image will wipe out the custom rom im on but not the data will leaving the data cause a problem? whats the command line to wipe data?
2. This doesnt address the boot loader locking issue causing a brick that people have been facing. This process involves updating the boot loader what do i have to do to make sure I dont brick my device?
Thanks again
kingofkings11 said:
Im a complete fastboot novice since this is my first nexus device (always had samsung phones up until now) and although I managed to root and unlock the boot loader I want to make sure I learn all the basics including flashing (side loading?) subsequent updates.
So Im currently rooted, unlocked bootloader on a 5.01. custom rom. How would I go about flashing the 5.1 update manually?
Im assuming that once I extract the update zip file I will find all the images that need to be flashed....what order do i do them in? How do I take into account the boot loader locking issue people have been facing that results in a bricked device?
Thanks in advance.
EDIT: I found this thread which outlines what I need to do http://forum.xda-developers.com/nexus-6/general/using-image-to-update-nexus-6-data-loss-t3053158
I only have two question now:
1. Im assuming the system image will wipe out the custom rom im on but not the data will leaving the data cause a problem? whats the command line to wipe data?
2. This doesnt address the boot loader locking issue causing a brick that people have been facing. This process involves updating the boot loader what do i have to do to make sure I dont brick my device?
Thanks again
Click to expand...
Click to collapse
You could simply not update the bootloader. Bare minimum requirements is update system and boot (kernel). if you want to learn more about fastboot, go to general > All in one guide > Question 28.
If you do not update the bootloader, you'll never get an OTA but it doesn't seem like you're wanting that anyway.
In regards to data, yes it could cause a problem if you're using a custom rom. You can use fastboot erase data command. This also wipes your /sdcard though.
My stock T-Mobile, unlocked bootloader N6 says that the 5.1.1. update is ready to install and then when I try to install it, it gets about 1/4 done and gives an error. I can reboot the phone at that point but the update never installs. Any suggestions? I've tried the factory reset and I get the same thing.
I downloaded the factory image and fastboot flashed the files.
Sent from my Nexus 6 using Tapatalk
Shift2win said:
My stock T-Mobile, unlocked bootloader N6 says that the 5.1.1. update is ready to install and then when I try to install it, it gets about 1/4 done and gives an error. I can reboot the phone at that point but the update never installs. Any suggestions? I've tried the factory reset and I get the same thing.
Click to expand...
Click to collapse
What error? Also, have you unencrypted?
Evolution_Tech said:
What error? Also, have you unencrypted?
Click to expand...
Click to collapse
Haven't unencrypted at all. The only "mod" has been the unlocking of the bootloader. Everything else is bone stock. And it just shows a picture of the Android robot laying down and it just says error underneath it.
Shift2win said:
Haven't unencrypted at all. The only "mod" has been the unlocking of the bootloader. Everything else is bone stock. And it just shows a picture of the Android robot laying down and it just says error underneath it.
Click to expand...
Click to collapse
Then as stated before, I recommend downloading the factory image, unzipping and flashing everything separately except userdata. Then you won't lose your data.
Shift2win said:
My stock T-Mobile, unlocked bootloader N6 says that the 5.1.1. update is ready to install and then when I try to install it, it gets about 1/4 done and gives an error. I can reboot the phone at that point but the update never installs. Any suggestions? I've tried the factory reset and I get the same thing.
Click to expand...
Click to collapse
Mine is doing the exact same, I'm also stock and on T-Mobile.
^same here...rooted and T-Mobile.
skipm said:
Mine is doing the exact same, I'm also stock and on T-Mobile.
Click to expand...
Click to collapse
n7plus1 said:
^same here...rooted and T-Mobile.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?p=61119896
Evolution_Tech said:
Then as stated before, I recommend downloading the factory image, unzipping and flashing everything separately except userdata. Then you won't lose your data.
Click to expand...
Click to collapse
I am rooted with stock recovery. Can I do this via ADB or do i need to install TWRP?
neudof said:
I am rooted with stock recovery. Can I do this via ADB or do i need to install TWRP?
Click to expand...
Click to collapse
Fastboot. You need an unlocked bootloader.
I have the same problem. I'm completely stock. Never done anything. I think it's a problem with the update. I've completely factory reset and wiped everything. I can't even get into the recovery mode. Just gives "no command" when I try.
robert_shipley said:
I have the same problem. I'm completely stock. Never done anything. I think it's a problem with the update. I've completely factory reset and wiped everything. I can't even get into the recovery mode. Just gives "no command" when I try.
Click to expand...
Click to collapse
That's exactly my problem, I'm completely stock and have to remain that way since I use my phone at work and they require the AirWatch MDM agent to be installed. I even tried deactivating AirWatch and uninstalling it and I still couldn't get the update to install. I hope there is some way they can either erase and download the update again or just overwrite the current one because this one definitely has problems.
Error you get if you look at recovery messages is
"Verifying current system...
System Partition has unexpected contents
E:Error in /cache/update.zip
(Status 7)
read elsewhere that something has modified a system file so OTA won't work and you'll need to flash full image (erasing everything in process) - which is my next step unless I want to wait for OTA to address the issue in the install procedure. No one has figured out what that item is that caused the change in system - some uninstalled Amazon appstore without success.
bchildress said:
Error you get if you look at recovery messages is
"Verifying current system...
System Partition has unexpected contents
E:Error in /cache/update.zip
(Status 7)
read elsewhere that something has modified a system file so OTA won't work and you'll need to flash full image (erasing everything in process) - which is my next step unless I want to wait for OTA to address the issue in the install procedure. No one has figured out what that item is that caused the change in system - some uninstalled Amazon appstore without success.
Click to expand...
Click to collapse
Just flash the system image. No need to flash everything. If you've unencrypted, then flash boot image too.
I have the same problem totaly stock, not rooted, untouched! I have the same error. I have 64 gb nexus 6 build number LMY47D.
Ok Guys,
Here is the solution,
1. Download stock image from google developer page, https://developers.google.com/android/nexus/images
2. Flash with long way;' DONT USE FLASH-ALL SCRIPT' (I tried, update fails again)
fastboot flash bootloader C:/image-shamu-XXXXXX/bootloader.img
fastboot reboot-bootloader
fastboot flash radio C:/image-shamu-XXXXXX/radio.img
fastboot reboot-bootloader
fastboot flash system C:/image-shamu-XXXXXX/system.img
fastboot flash userdata C:/image-shamu-XXXXXX/userdata.img
(Note: this command will wipe your device (including /sdcard), EVEN if your bootloader is already unlocked.)
fastboot flash boot C:/image-shamu-XXXXXX/boot.img
fastboot flash recovery C:/image-shamu-XXXXXX/recovery.img
fastboot erase cache
fastboot flash cache C:/image-shamu-XXXXXX/cache.img
(FOR FURTHER INFO PLS SEE THE PAGE; http://forum.xda-developers.com/nexus-6/general/guide-flash-factory-images-nexus-6shamu-t2954008)
3. Just turn on your N6 and it will find update and will be succesfull this time
Why do all that then OTA? Why not just flash everything but userdata from the LMY28E image? Boom your updated and you didn't lose data.
Evolution_Tech said:
Why do all that then OTA? Why not just flash everything but userdata from the LMY28E image? Boom your updated and you didn't lose data.
Click to expand...
Click to collapse
Hey,
I am Rooted with TWRP Recovery and Elemental X custom kernel, still encrypted with unlocked bootloader. I got the OTA (LMY47Z) notification and I have got the Factory Image as well as the OTA Zip. Can you guide me as to how can I update my Nexus (currently LMY47I) to 5.1.1 without losing any data?
Thanks.
The thing is which factory image for me?. Thats the reason i decided to do it via OTa. As u will see on developers page there are several versions,
5.1.0 (For T-Mobile ONLY) (LMY47M) Link 0469ca2018c923498cc603baae4fd648 5228e84a8a03609ead6b55df569057d5a4e28e0a
5.1.1 (For Sprint, USC ONLY) (LMY47Z) Link c8fe950ad9e861120a1074825b92cfba 33951732896055848d17b3876d8a39b79fb95301
5.1.1 (For T-Mobile ONLY) (LYZ28E) Link 9ea32a7ff1751afa2a16214ac23ef000 b542b88a0ad478110f9f111dd32b62a1cb65b9d5
So better to do it with the OTA.
peerpower said:
The thing is which factory image for me?. Thats the reason i decided to do it via OTa. As u will see on developers page there are several versions,
5.1.0 (For T-Mobile ONLY) (LMY47M) Link 0469ca2018c923498cc603baae4fd648 5228e84a8a03609ead6b55df569057d5a4e28e0a
5.1.1 (For Sprint, USC ONLY) (LMY47Z) Link c8fe950ad9e861120a1074825b92cfba 33951732896055848d17b3876d8a39b79fb95301
5.1.1 (For T-Mobile ONLY) (LYZ28E) Link 9ea32a7ff1751afa2a16214ac23ef000 b542b88a0ad478110f9f111dd32b62a1cb65b9d5
So better to do it with the OTA.
Click to expand...
Click to collapse
Download the OTA Zip, Extract it and check the "\META-INF\com\android\otacert" file to find the version number for your phone.
Hey guys,
I have an unlocked & rooted Nexus 6 (T-Mo, I believe) that I'm using for Google Fi. I'm currently on the 5.1.1 update that I got pre-root, when Project Fi pushed it to me. My build number (in About phone) is LYZ28E .
Today I was attempting to flash the official Stagefright update via TWRP, however it keeps failing with the following message:
Code:
Package expects build fingerprint of google/shamu/shamu:5.1.1/LYZ28E/1914015 : user/release-keys;
This device has Android/aosp_shamu/shamu: 5.0/LRX21M/dees_troy11191312 : userdebug/test-keys
Again, my ROM is the stock OTA that Google pushed me. I'm not running anything custom aside from TWRP. Any clue why the installer is showing my device as 5.0/LRX21M, when it's actually 5.1.1/LYZ28E?
Thanks in advance!
rvrzl said:
Hey guys,
I have an unlocked & rooted Nexus 6 (T-Mo, I believe) that I'm using for Google Fi. I'm currently on the 5.1.1 update that I got pre-root, when Project Fi pushed it to me. My build number (in About phone) is LYZ28E .
Today I was attempting to flash the official Stagefright update via TWRP, however it keeps failing with the following message:
Code:
Package expects build fingerprint of google/shamu/shamu:5.1.1/LYZ28E/1914015 : user/release-keys;
This device has Android/aosp_shamu/shamu: 5.0/LRX21M/dees_troy11191312 : userdebug/test-keys
Again, my ROM is the stock OTA that Google pushed me. I'm not running anything custom aside from TWRP. Any clue why the installer is showing my device as 5.0/LRX21M, when it's actually 5.1.1/LYZ28E?
Thanks in advance!
Click to expand...
Click to collapse
Can't flash the OTA in TWRP. Have to be completely stock. It is picking up the TWRP recovery build that does not match stock recovery. TWRP is built from AOSP source and dees_troy is one of the devs.
prdog1 said:
Can't flash the OTA in TWRP. Have to be completely stock. It is picking up the TWRP recovery build that does not match stock recovery. TWRP is built from AOSP source and dees_troy is one of the devs.
Click to expand...
Click to collapse
Oh, I thought you could flash it as long as you downloaded and flashed it manually via recovery, instead of letting the OTA do it's thing automatically. Bummer!
There's no way to remove the recovery without doing a full re-flash either, right? It certainly seems like an exploit worthy of my time to patch, but I was trying to avoid the data loss :/
rvrzl said:
Oh, I thought you could flash it as long as you downloaded and flashed it manually via recovery, instead of letting the OTA do it's thing automatically. Bummer!
There's no way to remove the recovery without doing a full re-flash, right? It certainly seems like an exploit worth of my time to patch, but I was trying to avoid the data loss :/
Click to expand...
Click to collapse
You can fastboot flash the corresponding factory images. Skip the userdata data image and will will not wipe data. OTA's are worthless if gonna run root and recovery. Someone may make a TWRP flashable. Would have to search for it.
Awesome, I'll dig around and figure out how to skip certain images while flashing and give that a try (I've never had to do that before). I'm pretty comfortable in the terminal though, so I'm not too worried. Thanks for your help, @prdog1
rvrzl said:
Awesome, I'll dig around and figure out how to skip certain images while flashing and give that a try (I've never had to do that before). I'm pretty comfortable in the terminal though, so I'm not too worried. Thanks for your help, @prdog1
Click to expand...
Click to collapse
If you're running root, fastboot flash the system.img only. If you don't run a custom kernel, you probably should also fastboot flash the boot.img too.
Keep supersu on your sdcard and after flashing system DO NOT boot the rom. Boot straight into TWRP and flash supersu
If you boot rom install-recovery.sh will install stock recovery on first boot. .flashing super su amended this script so that won't happen.
You can also flash the radio.img. Your choice.
rvrzl said:
I have an unlocked & rooted Nexus 6 (T-Mo, I My build number is LYZ28E .
Today I was attempting to flash the official Stagefright update via TWRP,
Any clue why the installer is showing my device as 5.0/LRX21M, when it's actually 5.1.1/LYZ28E?
Click to expand...
Click to collapse
For OTA's the device needs to be unrooted and complete stock. Including 'recovery'. So flashing with TWRP-recovery will not work.
An alternative is to flash only the new system.img with fastboot.
FWIW, recovery flashable updates are here:
http://forum.xda-developers.com/showthread.php?t=3066052
rvrzl said:
Hey guys,
I have an unlocked & rooted Nexus 6 (T-Mo, I believe) that I'm using for Google Fi. I'm currently on the 5.1.1 update that I got pre-root, when Project Fi pushed it to me. My build number (in About phone) is LYZ28E .
Today I was attempting to flash the official Stagefright update via TWRP, however it keeps failing with the following message:
Code:
Package expects build fingerprint of google/shamu/shamu:5.1.1/LYZ28E/1914015 : user/release-keys;
This device has Android/aosp_shamu/shamu: 5.0/LRX21M/dees_troy11191312 : userdebug/test-keys
Again, my ROM is the stock OTA that Google pushed me. I'm not running anything custom aside from TWRP. Any clue why the installer is showing my device as 5.0/LRX21M, when it's actually 5.1.1/LYZ28E?
Thanks in advance!
Click to expand...
Click to collapse
I'm having the exact same issue, but theirs gotta be a way around it, not sure how it does it but if I use the sideload option in NRT then it somehow boots STOCK recovery to flash the OTA, problem then for me is I loose connectivity when that happens. I retain sideload ADB connectivity when I try in Linux, but can't get the phone into stock recovery that way. If I can't get it in by the weekend guess I gotta fully return the phone to stock to get that update in. Hopefully somebody figures it out.
snatale1 said:
I'm having the exact same issue, but theirs gotta be a way around it, not sure how it does it but if I use the sideload option in NRT then it somehow boots STOCK recovery to flash the OTA, problem then for me is I loose connectivity when that happens. I retain sideload ADB connectivity when I try in Linux, but can't get the phone into stock recovery that way. If I can't get it in by the weekend guess I gotta fully return the phone to stock to get that update in. Hopefully somebody figures it out.
Click to expand...
Click to collapse
Booting to a stock recovery is easy.
"fastboot boot recovery.img"
Then you can adb sideload, as long as your rom is entirely stock and never rooted.
That said, fastboot flashing the system.img would probably be quicker.
snatale1 said:
I'm having the exact same issue, but theirs gotta be a way around it, not sure how it does it but if I use the sideload option in NRT then it somehow boots STOCK recovery to flash the OTA, problem then for me is I loose connectivity when that happens. I retain sideload ADB connectivity when I try in Linux, but can't get the phone into stock recovery that way. If I can't get it in by the weekend guess I gotta fully return the phone to stock to get that update in. Hopefully somebody figures it out.
Click to expand...
Click to collapse
You can flash the OTA all day anyway you want but if you are not stock it won't take. Only other way is one of the flashable TWRP versions that were linked to. And right now looks like that thread is down for update.
danarama said:
Booting to a stock recovery is easy.
"fastboot boot recovery.img"
Then you can adb sideload, as long as your rom is entirely stock and never rooted.
That said, fastboot flashing the system.img would probably be quicker.
Click to expand...
Click to collapse
If I am running everything stock apart from the recovery (using TWRP), with an unlocked bootloader and the device is not rooted, can I simply flash the stock recovery.img without losing any of my data? Is it really that simple? Do I have to use a particular recovery.img?
All I want to do is restore the stock recovery so I can OTA the stagefright update. TWRP is preventing me from doing so at the moment, but I don't want to lose all my data.
rvrzl said:
Today I was attempting to flash the official Stagefright update via TWRP, however it keeps failing with the following message:
Code:
Package expects build fingerprint of google/shamu/shamu:5.1.1/LYZ28E/1914015 : user/release-keys;
This device has Android/aosp_shamu/shamu: 5.0/LRX21M/dees_troy11191312 : userdebug/test-keys
!
Click to expand...
Click to collapse
Because of this, I did the update twice; different methods, to see of there are possible differences.
Differences between official OTA and flashing the new system.img only.
Update 1: Flashing only the new system image (1,7 Gb) with fastboot.
Update 2: Return to stock LMY47Z and install official OTA (24,2 Mb)
Both updates have the same results. Data and apps were kept but there were changes:
a. Changes in build.prop gone (DPI, Wifi interval);
b. Standard icons because the DPI value 384 was changed to 560;
c. BGN-launcher replaced. Google Now launcher became white again;
d. Root gone (SuperSu and Busybox);
(Update 2. Of course returning to stock, replaces the custom kernel).
After rerooting the N6 the following actions were needed after both update methods:
- edit the file: system/build.prop to change the dpi and wifi interval;
- reflash/reinstall: BGN-Launcher, SuperSU and Busybox;
- uninstall updates of the Google app to get BGN-launcher working;
- replacing icons from drawer to start screen.
So when you have made changes to the system, like DPI settings, an update will leave your data alone, but not the settings.
Clawz114 said:
If I am running everything stock apart from the recovery (using TWRP), with an unlocked bootloader and the device is not rooted, can I simply flash the stock recovery.img without losing any of my data? Is it really that simple? Do I have to use a particular recovery.img?
All I want to do is restore the stock recovery so I can OTA the stagefright update. TWRP is preventing me from doing so at the moment, but I don't want to lose all my data.
Click to expand...
Click to collapse
Yes, that is all you have to do: flash the stock recovery corresponding to the Android build you are currently using. You will not lose any data. Remember, data is stored on the userdata partition, so as long as you don't flash that image, all your data will be left intact.
Sent from my Nexus 5 using Tapatalk
efrant said:
Yes, that is all you have to do: flash the stock recovery corresponding to the Android build you are currently using. You will not lose any data. Remember, data is stored on the userdata partition, so as long as you don't flash that image, all your data will be left intact.
Sent from my Nexus 5 using Tapatalk
Click to expand...
Click to collapse
Thanks, I flashed the LYZ28E recovery and all seemed well. However, I then went to install the OTA, and it ended up giving me the error, with the Android on it's back and the exclamation mark. Rebooted the phone and apparently "Your system is up to date".
efrant said:
Yes, that is all you have to do: flash the stock recovery corresponding to the Android build you are currently using. You will not lose any data. Remember, data is stored on the userdata partition, so as long as you don't flash that image, all your data will be left intact.
Sent from my Nexus 5 using Tapatalk
Click to expand...
Click to collapse
The OTA doesn't check the recovery version, since it replaces recovery on first boot anyway. Only matters that its stock.
That said, the only reason not to flash the rightbversiin is if the download link.is down or you have a local copy of a different version anyway.
Clawz114 said:
Thanks, I flashed the LYZ28E recovery and all seemed well. However, I then went to install the OTA, and it ended up giving me the error, with the Android on it's back and the exclamation mark. Rebooted the phone and apparently "Your system is up to date".
Click to expand...
Click to collapse
The exclamation mark isn't an error. That's the stock recovery splash screen. You have to press vol up + power at that screen to get to the menu
How are you trying to flash the OTA?
By unrooted, lets be clear. The rom must never have been rooted. Unrooting a rom won't work
Clawz114 said:
Thanks, I flashed the LYZ28E recovery and all seemed well. However, I then went to install the OTA, and it ended up giving me the error, with the Android on it's back and the exclamation mark. Rebooted the phone and apparently "Your system is up to date".
Click to expand...
Click to collapse
What is the error?
danarama said:
[snip]
The OTA doesn't check the recovery version, since it replaces recovery on first boot anyway. Only matters that its stock.
Click to expand...
Click to collapse
You are right, the OTA doesn't check the version of the recovery. However, I can tell you for a fact that on older Nexus devices, using a recovery from a different version of Android would not allow an update to flash. (It is possible this has changed since then though.) I remember very clearly, helping many users troubleshoot (particularly given that the only available toolkit at the time would flash only one generic stock recovery, and not a specific version), and it was confirmed that the errors users were having were due to using a wrong version of the stock recovery, so the recovery version did indeed matter (at least on the Galaxy Nexus it did).
danarama said:
The exclamation mark isn't an error. That's the stock recovery splash screen. You have to press vol up + power at that screen to get to the menu
Click to expand...
Click to collapse
I press install update now, let the phone reboot and I get the installation screen with the progress bar. It sits at about 10% filled for about 10 seconds then I get the picture of the android laying on it's back with a red triangle and an exclamation mark. Underneath that it just says "Error!".
danarama said:
How are you trying to flash the OTA?
Click to expand...
Click to collapse
The only thing I flashed was a stock recovery.img, to replace TWRP. I am trying to get the latest update the normal way, by getting the notification I have an update available, and pressing install update now.
danarama said:
By unrooted, lets be clear. The rom must never have been rooted. Unrooting a rom won't work
Click to expand...
Click to collapse
I have never rooted the phone. I updated the phone manually a while back and long story short, I flashed TWRP recovery instead of the stock recovery as I intended to. I just want to revert everything back to stock (which it should be now that I have replaced TWRP with stock recovery)
efrant said:
What is the error?
Click to expand...
Click to collapse
As above, it's picture of the android laying on it's back with a red triangle and an exclamation mark. Underneath that it just says "Error!".
efrant said:
What is the error?
You are right, the OTA doesn't check the version of the recovery. However, I can tell you for a fact that on older Nexus devices, using a recovery from a different version of Android would not allow an update to flash. (It is possible this has changed since then though.) I remember very clearly, helping many users troubleshoot (particularly given that the only available toolkit at the time would flash only one generic stock recovery, and not a specific version), and it was confirmed that the errors users were having were due to using a wrong version of the stock recovery, so the recovery version did indeed matter (at least on the Galaxy Nexus it did).
Click to expand...
Click to collapse
I believe it changed for lollipop OTA's. I don't think it had changed for kitKat.
---------- Post added at 03:03 PM ---------- Previous post was at 03:01 PM ----------
Clawz114 said:
I press install update now, let the phone reboot and I get the installation screen with the progress bar. It sits at about 10% filled for about 10 seconds then I get the picture of the android laying on it's back with a red triangle and an exclamation mark. Underneath that it just says "Error!".
The only thing I flashed was a stock recovery.img, to replace TWRP. I am trying to get the latest update the normal way, by getting the notification I have an update available, and pressing install update now.
I have never rooted the phone. I updated the phone manually a while back and long story short, I flashed TWRP recovery instead of the stock recovery as I intended to. I just want to revert everything back to stock (which it should be now that I have replaced TWRP with stock recovery)
As above, it's picture of the android laying on it's back with a red triangle and an exclamation mark. Underneath that it just says "Error!".
Click to expand...
Click to collapse
If you're.familiar with fastboot already, why not just download the full factory image and flash system, boot, bootloader, radio and recovery images?
danarama said:
If you're.familiar with fastboot already, why not just download the full factory image and flash system, boot, bootloader, radio and recovery images?
Click to expand...
Click to collapse
I'm going to have to do just that by the looks of it.