[Q] Xperia T LT30at is stuck at Sony screen.[SOLVED] - Sony Xperia T, TL, TX, V

The problem.
When I boot the device it just stays at the Sony screen and does not progress any further. I am still able to turn off the device by holding the power button and the volume up button, I can reset it by holding the button longer waiting for the vibration, and I can hard reset by waiting till the three vibrations.
What I was doing up to the point it happened.
I was trying to get a custom ROM on my device, I had it previously rooted so I thought I would go further. I installed CWM on my phone I wiped data, cache, and dalvick then I went to install the ROM from SD card. During the attempt at installation I got some symlink errors with a status of 7. Not sure what to do turned off the device when I decided to put back its previous I turned it back on and arrived at the problem.
What I have done to try and fix it.
I have done the soft and hard resets, I tried using the PC companions repair tool. When it asks me to turn the device off hold down the power button then plug in the device nothing happens(I have tried this several times.) I downloaded the flashtool and the correct ftf and tried using that, but it doesn't detect my device when I hold down the volume button and plug it in. So it seems that the flashboot is not working on my phone.
Any suggestions on what to try would be much appreciated and thanks in advanced.

tabersays said:
The problem.
When I boot the device it just stays at the Sony screen and does not progress any further. I am still able to turn off the device by holding the power button and the volume up button, I can reset it by holding the button longer waiting for the vibration, and I can hard reset by waiting till the three vibrations.
What I was doing up to the point it happened.
I was trying to get a custom ROM on my device, I had it previously rooted so I thought I would go further. I installed CWM on my phone I wiped data, cache, and dalvick then I went to install the ROM from SD card. During the attempt at installation I got some symlink errors with a status of 7. Not sure what to do turned off the device when I decided to put back its previous I turned it back on and arrived at the problem.
What I have done to try and fix it.
I have done the soft and hard resets, I tried using the PC companions repair tool. When it asks me to turn the device off hold down the power button then plug in the device nothing happens(I have tried this several times.) I downloaded the flashtool and the correct ftf and tried using that, but it doesn't detect my device when I hold down the volume button and plug it in. So it seems that the flashboot is not working on my phone.
Any suggestions on what to try would be much appreciated and thanks in advanced.
Click to expand...
Click to collapse
You probably didn't install the ADB drivers. Install them from the Flashtool folder (use the ones for TX) and then try flashing your stock FTF again. Remember to put the device into Flashmode.
Basically what happened was that while flashing your ROM the script that flashes everything deletes everything from the /system partition, then you got an error and the installation was incomplete, therefore there is no proper system to boot into. You could have easily avoided what happened by flashing a different ROM had you not powered off.

Antiga Prime said:
You probably didn't install the ADB drivers. Install them from the Flashtool folder (use the ones for TX) and then try flashing your stock FTF again. Remember to put the device into Flashmode.
Basically what happened was that while flashing your ROM the script that flashes everything deletes everything from the /system partition, then you got an error and the installation was incomplete, therefore there is no proper system to boot into. You could have easily avoided what happened by flashing a different ROM had you not powered off.
Click to expand...
Click to collapse
Thank you for response, I went and used the Flashtool-driver.exe and installed the Flashmode drivers, Fastboot drivers and the TX drivers. But it does not seem to have changed anything. To enter flash mode on the phone one has to hold down the volume down button while plugging the phone into the usb when it is powered off, right? Flash tool just sits at the instruction animation titled Wait for Flashmode. When I try to enter flashmode I do not get a response from either the program or the phone. Any more suggestions would be welcomed.
Thank you for taking the time to help.

tabersays said:
To enter flash mode on the phone one has to hold down the volume down button while plugging the phone into the usb when it is powered off, right? Flash tool just sits at the instruction animation titled Wait for Flashmode. When I try to enter flashmode I do not get a response from either the program or the phone. Any more suggestions would be welcomed.
Thank you for taking the time to help.
Click to expand...
Click to collapse
Yes, that is how you enter flashmode. Turn off phone, and keep volume down button pressed while you connect the USB cable; the LED light should turn on with a green light. If you're phone is not entering Flashmode, then you might have a faulty USB cable, or there might be problems with your USB ports, either on your computer or your phone (try with different cables/computers).
Also, check your Device Manager (while phone is connected) to make sure the drivers are properly installed. If you have Windows 8, you should have had to turn of Driver Signature Checking in order for the drivers to install properly.

Antiga Prime said:
Also, check your Device Manager (while phone is connected) to make sure the drivers are properly installed. If you have Windows 8, you should have had to turn of Driver Signature Checking in order for the drivers to install properly.
Click to expand...
Click to collapse
Yes, it's better to work on Windows 7 or lower....

Antiga Prime said:
Yes, that is how you enter flashmode. Turn off phone, and keep volume down button pressed while you connect the USB cable; the LED light should turn on with a green light. If you're phone is not entering Flashmode, then you might have a faulty USB cable, or there might be problems with your USB ports, either on your computer or your phone (try with different cables/computers).
Also, check your Device Manager (while phone is connected) to make sure the drivers are properly installed. If you have Windows 8, you should have had to turn of Driver Signature Checking in order for the drivers to install properly.
Click to expand...
Click to collapse
Yeah I turned off the Driver signature checking on my computer when I did it. I'll go buy a new cable and try a friends windows 7 computer. Hopefully there is nothing wrong with the USB port in my phone. Thank you for your help I'll let you know how it goes.

Thank you everybody for your support. My phone is now working. After my phones battery died I was able to get it charging, when it had enough energy it booted itself to the Sony screen so I turned it off and grabbed my new micro USB cable and was able to get it into flash mode. Everything is now working great. I wish a special thanks to Antiga Prime for taking the time to help me.

Related

[Q] Xperia T will not go past Sony logo

Hi, I have tried to use flashtools and I've got all the necessary drivers (I think) but once I put hold power button and vol+ (3 vibrations), then press vol-, connect to pc via USB and I get a temporary green led, which goes after about 5 seconds, and then my phone disconnects from my computer again and i get a constant red led while the Sony logo appears. I really need my phone to work Could someone out there please help with this! I would really appreciate if someone responded very soon as I would like to get this sorted as soon as possible. Flashtools gives me these messages:
22/012/2013 23:12:07 - INFO - Device disconnected
22/029/2013 23:29:07 - INFO - Device connected in flash mode
22/029/2013 23:29:18 - INFO - Device disconnected
Also one more thing I'd like to add.. Once I go into that BLU thing, it keeps on asking me what device I have, so I select Xperia T and then it gives the following messages:
22/052/2013 22:52:26 - INFO - Your phone bootloader cannot be officially unlocked
22/052/2013 22:52:26 - INFO - You can now unplug and restart your phone
Might this have something to do with it? Any suggestions would be grateful! I've been at this for hours now and need to get this sorted
Thanks to any kind person who helps fix this!
1) Dial *#*#7378423#*#* and goto software info/configuaration. If it says bootloader unlocked allowed: no, then you CANNOT unlock it via ANY means
2) If it says yes (I doubt it, because flashtool has already checked this) then you can.
3) Flashmode has nothing to do with bootloader. Press volume up to get into fastboot (Blue LED) for working with bootloader, press volume down (Green LED) to work in flashmode, which is for flashing FTF's.
4) If you are trying to flash a FTF, then do not connect the phone until it asks
5)Make sure you have gone to C:\flashtool\drivers and run drivers.exe. Ensure you choose fastboot, flashmode and TX drivers.
6) Make sure you are on the latest version of flashtool 0.9.13.1
Can I ask what you are actually trying to do?
Also flashmode and fastboot and adb dont work on windows 8(.1)
gregbradley said:
1) Dial *#*#7378423#*#* and goto software info/configuaration. If it says bootloader unlocked allowed: no, then you CANNOT unlock it via ANY means
2) If it says yes (I doubt it, because flashtool has already checked this) then you can.
3) Flashmode has nothing to do with bootloader. Press volume up to get into fastboot (Blue LED) for working with bootloader, press volume down (Green LED) to work in flashmode, which is for flashing FTF's.
4) If you are trying to flash a FTF, then do not connect the phone until it asks
5)Make sure you have gone to C:\flashtool\drivers and run drivers.exe. Ensure you choose fastboot, flashmode and TX drivers.
6) Make sure you are on the latest version of flashtool 0.9.13.1
Can I ask what you are actually trying to do?
Click to expand...
Click to collapse
Its not even booting, past the Sony logo so i cannot do anything (i can't do step 1 as you've asked). Its literally a bootloop. Can you give me step-by-step instructions to get out of this bootloop? I tried to install custom ROM but it died on me, and now its on the bootloop, which i can't get passed.
hhamzah49 said:
Also flashmode and fastboot and adb dont work on windows 8(.1)
Click to expand...
Click to collapse
Oh okay. I'm using windows 8.1, so what would I do to fix the issue?
I have given my phone to the manufacturers to try and sort out but I have a feeling they will refuse to fix it, so any help would be appreciated. If i use a windows 7 machine, would it work? If so, how do I fix it such that it exits bootloop and allows me to access my phone. I don't mind losing all my data (although i think its lost anyway lol)
P.S. thanks for the reply.
fizstarrr said:
Oh okay. I'm using windows 8.1, so what would I do to fix the issue?
Click to expand...
Click to collapse
use windows 7 or linux. i read about problems with win8.1 too. thats why i not updated my win8 yet.
immerblind said:
use windows 7 or linux. i read about problems with win8.1 too. thats why i not updated my win8 yet.
Click to expand...
Click to collapse
Question is, will is definitely work if i use windows 7? I.e. is the fact that i'm using windows 8.1 the reason why it's not working?
fizstarrr said:
Hi, I have tried to use flashtools and I've got all the necessary drivers (I think) but once I put hold power button and vol+ (3 vibrations), then press vol-, connect to pc via USB and I get a temporary green led, which goes after about 5 seconds, and then my phone disconnects from my computer again and i get a constant red led while the Sony logo appears. I really need my phone to work Could someone out there please help with this! I would really appreciate if someone responded very soon as I would like to get this sorted as soon as possible. Flashtools gives me these messages:
22/012/2013 23:12:07 - INFO - Device disconnected
22/029/2013 23:29:07 - INFO - Device connected in flash mode
22/029/2013 23:29:18 - INFO - Device disconnected
Also one more thing I'd like to add.. Once I go into that BLU thing, it keeps on asking me what device I have, so I select Xperia T and then it gives the following messages:
22/052/2013 22:52:26 - INFO - Your phone bootloader cannot be officially unlocked
22/052/2013 22:52:26 - INFO - You can now unplug and restart your phone
Might this have something to do with it? Any suggestions would be grateful! I've been at this for hours now and need to get this sorted
Thanks to any kind person who helps fix this!
Click to expand...
Click to collapse
I'm sure your batt is dead. Try the rubber band method. Give it like 2/3 rounds of it on the power button and hold it and plug in charger. it should charge with red led on. Pull battery and try again if it does not charge. Give it some charging and it should be able to enter flashmode to flash stock.
Unknownkj said:
I'm sure your batt is dead. Try the rubber band method. Give it like 2/3 rounds of it on the power button and hold it and plug in charger. it should charge with red led on. Pull battery and try again if it does not charge. Give it some charging and it should be able to enter flashmode to flash stock.
Click to expand...
Click to collapse
I don't think the battery is dead, as the led would just blink and wouldn't even show me the Sony logo.. Everytime i use the phone with the charger it goes into the bootloop, looping around the Sony logo and then switching off again, then the sony logo will show again, etc. I've sent it off to Sony manufaturers. Would they fix it (even if the manufacturers warranty is void)? Like, even if they charge a little (hopefully not stupid amounts of money lol)? If not, i'm going to try and use flashtool on windows 7 machine and hope that it works, as I've heard flashmode and fastboot and adb do not work on windows 8(.1), which is what im currently using :crying:
fizstarrr said:
I don't think the battery is dead, as the led would just blink and wouldn't even show me the Sony logo.. Everytime i use the phone with the charger it goes into the bootloop, looping around the Sony logo and then switching off again, then the sony logo will show again, etc. I've sent it off to Sony manufaturers. Would they fix it (even if the manufacturers warranty is void)? Like, even if they charge a little (hopefully not stupid amounts of money lol)? If not, i'm going to try and use flashtool on windows 7 machine and hope that it works, as I've heard flashmode and fastboot and adb do not work on windows 8(.1), which is what im currently using :crying:
Click to expand...
Click to collapse
Hello. Have you tried hard reset?
Press power button and vol up key together until it vibrates. Phone should start up?
Sent from my LT30p using xda premium
fizstarrr said:
Question is, will is definitely work if i use windows 7? I.e. is the fact that i'm using windows 8.1 the reason why it's not working?
Click to expand...
Click to collapse
Yes (or, at least its definitely one of the reasons). Use Win 8 or Win 7 or Win XP.
If after that point you still have trouble with it sticking to flashmode: I also had trouble flashing via flashmode with one of my USB ports. I like to use the front ones on my PC but they don't work for every device. There is also a USB cable that I have that does not work for flashmode. Consider these 2 things
LaZiODROID said:
Yes (or, at least its definitely one of the reasons). Use Win 8 or Win 7 or Win XP.
If after that point you still have trouble with it sticking to flashmode: I also had trouble flashing via flashmode with one of my USB ports. I like to use the front ones on my PC but they don't work for every device. There is also a USB cable that I have that does not work for flashmode. Consider these 2 things
Click to expand...
Click to collapse
I'll try windows 7 when I get it back. And wow really? I didn't realise that using different cables actually made a difference? At the end of the day, if it charges the phone it should work! Lol, Sony know how to make things real complicated!
Experia T stuck on SONY logo
Help, another help
I read about the leaked 4.3 and the latest 4.4
Did much flashing with HTC Desire.
Now I made a big mistake trying something with my Xperia T
Using DooMLorD flashtool I got into fastboot mode and then clicked on 'Reboot device into system'
I WISH I HADN'T
Now my Xperia T is dead.
Starting up it gets stuck on the SONY logo, nothing, nothing happens.
Please help me recover the device!
HvdW said:
Help, another help
I read about the leaked 4.3 and the latest 4.4
Did much flashing with HTC Desire.
Now I made a big mistake trying something with my Xperia T
Using DooMLorD flashtool I got into fastboot mode and then clicked on 'Reboot device into system'
I WISH I HADN'T
Now my Xperia T is dead.
Starting up it gets stuck on the SONY logo, nothing, nothing happens.
Please help me recover the device!
Click to expand...
Click to collapse
It's just a soft brick. What did you wanted to flash? Just flash a stock .ftf file with flashtool, or a kernel with recovery.
St.Jimmy90 said:
It's just a soft brick. What did you wanted to flash? Just flash a stock .ftf file with flashtool, or a kernel with recovery.
Click to expand...
Click to collapse
Well, first of all I want the phone to start up normally again so that I can use it.
What I did achieve up till now is that I can get it connected to flashtool in Fastboot mode.
I guess this gives me the opportunity to flash a boot.img first so that I can install 4.4 or 4.3 later.
But first things first.
Do you think flashing a boot.img could restore the phone in a state that it functions as a normal phone again?
HvdW said:
Well, first of all I want the phone to start up normally again so that I can use it.
What I did achieve up till now is that I can get it connected to flashtool in Fastboot mode.
I guess this gives me the opportunity to flash a boot.img first so that I can install 4.4 or 4.3 later.
But first things first.
Do you think flashing a boot.img could restore the phone in a state that it functions as a normal phone again?
Click to expand...
Click to collapse
My xperia t has gone in for repair. Before considering this though, could you try one thing to see if it'll help restore phone? Go to your PC companion (and no, its not a standard recovery which i'm going to suggest so keep reading!). Once you have done this, click on "Support zone". Click "Start" on the "Phone/tablet software update" option. Note, you do not need to plug in your device yet!. You should get an error message coming up saying device not connected. And once you get this, there should be a message asking you whether you are having "severe problems with your phone/tablet". There's a "repair my phone/tablet" hyperlink. I want you to click that and NOT the connect button. Once you have clicked that, please follow the on screen instructions. Tell me if this works for you I hope it does!
fizstarrr said:
My xperia t has gone in for repair. Before considering this though, could you try one thing to see if it'll help restore phone? Go to your PC companion (and no, its not a standard recovery which i'm going to suggest so keep reading!). Once you have done this, click on "Support zone". Click "Start" on the "Phone/tablet software update" option. Note, you do not need to plug in your device yet!. You should get an error message coming up saying device not connected. And once you get this, there should be a message asking you whether you are having "severe problems with your phone/tablet". There's a "repair my phone/tablet" hyperlink. I want you to click that and NOT the connect button. Once you have clicked that, please follow the on screen instructions. Tell me if this works for you I hope it does!
Click to expand...
Click to collapse
No it dod not.
Why?
Because SONY decided that I have made changes to my phone and SONY now refuses to repair my device.
HvdW said:
No it dod not.
Why?
Because SONY decided that I have made changes to my phone and SONY now refuses to repair my device.
Click to expand...
Click to collapse
Ah that sucks! Are you not on windows 8? I've heard that windows 8 and flashtools don't get along, but if you're saying you've got your device into fastboot you should be able to flash it using flashtools!
Sony Xperia T LT30p dead resolved
OK, here it is for those interested on how to revive a dead Xperia device.
Yesterday my phone stalled at the SONY logo.
Nothing could be done anymore.
My phone has returned into normal state thanks to SonyXperiakiasT :good:
Follow this thread: http://forum.xda-developers.com/showthread.php?t=2315572
Howto get into a state that one can flash the phone.
- download: LT30P_9.1.A.1.141_PL.ftf (the original firmware)
- install and activate flashtool-0.9.13.0-windows.exe
- at the SONY logo push on/off, vol-up and vol-down together
- when the phone vibrates an the logo disappears release all buttons and immediately after push on/off and vol-up button
- when phone vibrates release on/off button, keep pushing vol-up button and plug in USB cable from computer
- you will be in a state with a blue light at the top left of your phone.
- however you want to get in a state with a green led
- push vol-down and on/off
- unplug the USB
- wait for the phone to vibrate
- release the on/off button and plug in the USB
- Follow the instructions in the thread mentioned above and your phone will be revived.
All the pushing, releasing, plugging and unplugging is a quite delicate affair.
I tried it during several hours before I got a bit of grip on it and still I am not shure how I got into the green led state.
Try it, be patient and be shure that repair is within reach as soon as you have a green LED on your phone.
Good luck!
Hein
HvdW said:
OK, here it is for those interested on how to revive a dead Xperia device.
Yesterday my phone stalled at the SONY logo.
Nothing could be done anymore.
My phone has returned into normal state thanks to SonyXperiakiasT :good:
Follow this thread: http://forum.xda-developers.com/showthread.php?t=2315572
Howto get into a state that one can flash the phone.
- download: LT30P_9.1.A.1.141_PL.ftf (the original firmware)
- install and activate flashtool-0.9.13.0-windows.exe
- at the SONY logo push on/off, vol-up and vol-down together
- when the phone vibrates an the logo disappears release all buttons and immediately after push on/off and vol-up button
- when phone vibrates release on/off button, keep pushing vol-up button and plug in USB cable from computer
- you will be in a state with a blue light at the top left of your phone.
- however you want to get in a state with a green led
- push vol-down and on/off
- unplug the USB
- wait for the phone to vibrate
- release the on/off button and plug in the USB
- Follow the instructions in the thread mentioned above and your phone will be revived.
All the pushing, releasing, plugging and unplugging is a quite delicate affair.
I tried it during several hours before I got a bit of grip on it and still I am not shure how I got into the green led state.
Try it, be patient and be shure that repair is within reach as soon as you have a green LED on your phone.
Good luck!
Hein
Click to expand...
Click to collapse
Hey so I ran into this same problem! my phone wouldn't do anything except boot up to the Sony screen, no lights no charging nothing
I figured it out, at least for me
>Have your flash ready to go via Flashtool
>Have your phone plugged into your computer via USB
>Hold the volume down button and then while holding it turn it on
you should have your green light and may have to hold the volume button the whole time until its done flashing.
Hope this works
FIX!
Hey the same thing happened to my xp T few days ago. My phone was rooted with UB. I was stuck on SONY LOGO too n my phone was rebooting from there repeatedly but I was managed to get into cwm n I installeddifferent kernels + Rome but it was no good. Like u said in your OP I couldn't get into flashmood too. When I select the firmware flashtools say preparing files then the phone reboots! Then flashtools say device disconnected!! The solution for this is when flashtools says device disconnected pull the usb cable n press vol up with power button n turn off phone. Then once turned off straight away press vol down n plug in usb cable n flashtools will start flashing. The important thing here is not to close the window that pops up when flashtool say device disconnected in red. Hope this helps, same prob worked for me so should work for you! Peace

Have I hard-bricked my device?

Please excuse me if I'm repeating a prior question but it seems far too specific to trawl through pages of related threads to make sure.
I decided I was going to sit down and root my Xperia Z1....
Steps:
1. I installed ADB and Fastboot via the latest windows Android SDK (r23-.0.2), in fact I had to source a sony version of the fastboot driver in order to get it working but once I'd done that all went ahead as planned.
2. Generally followed this guide (wont let me post a link but google "honami cyanogenmod" and it's the 2nd result)
3. All was going swimmingly, I entered fastboot mode absolutely fine, flashed CWM using fastboot which all loaded up absolutely fine.
3. At this stage ADB was not picking up my device at all, tried different cables, ports, all of the usual. What I didn't do was make a backup, and then I wiped all of the things that it's possible to wipe thinking to myself that I was going to get Cyanogenmod on there so all would be fine...
4. Finally I (quite stupidly) restored from memory card (which had already been wiped) from inside CWM, the device restarted and now I am getting no response AT ALL.
5. Sometimes it will load the Sony 'splash' logo that first appears but sometimes not, when plugged in the device is recognised and ADB actually sees the device but lists it as offline... Interestingly at this stage windows device installer actually installs Sony ADB driver for me automatically.
6. All I'm getting at the moment is a red flashing LED although when I plug in via USB the device is again recognised when I type adb devices but again is offline...
If any more information is needed please, I will be more than happy to give a quick reply.
Thank you in advance
JJrmc said:
I decided I was going to sit down and root my Xperia Z1....
Steps:
1. I installed ADB and Fastboot via the latest windows Android SDK (r23-.0.2), in fact I had to source a sony version of the fastboot driver in order to get it working but once I'd done that all went ahead as planned.
2. Generally followed this guide (wont let me post a link but google "honami cyanogenmod" and it's the 2nd result)
Click to expand...
Click to collapse
Were you trying to root your phone or install cyanogenmod? You followed a guide to install cyanogenmod on xperia Z1.
AkiraProject said:
Were you trying to root your phone or install cyanogenmod? You followed a guide to install cyanogenmod on xperia Z1.
Click to expand...
Click to collapse
I was trying to end up with a rooted device running Cyanogenmod, I've been putting it off and off looking into the whole rooting scene and mistakenly dived in a little too quick without knowing what I was doing.
after that you move cm-11-20141112-SNAPSHOT-M12-honami.zip to your sd card. Now you have flashed boot.img you can't move zip to your sd card using z1 you had to do that before using fastboot. use some sd card adapter and do it. then put the sd card back in your phone. turn it on then enter the cwm recovery pressing Vol+ for a few seconds when the sony logo shows up. select full wipe data. then install from zip. choose cm-11-20141112-SNAPSHOT-M12-honami.zip. reboot. ADB won't work until you have installed cyanogenmod zip. You have only installed cyanogenmod kernel and custom recovery when you flashed the boot.img.
AkiraProject said:
after that you move cm-11-20141112-SNAPSHOT-M12-honami.zip to your sd card. Now you have flashed boot.img you can't move zip to your sd card using z1 you had to do that before using fastboot. use some sd card adapter and do it. then put the sd card back in your phone. turn it on then enter the cwm recovery pressing Vol+ for a few seconds when the sony logo shows up. select full wipe data. then install from zip. choose cm-11-20141112-SNAPSHOT-M12-honami.zip. reboot. ADB won't work until you have installed cyanogenmod zip. You have only installed cyanogenmod kernel and custom recovery when you flashed the boot.img.
Click to expand...
Click to collapse
Firstly AkiraProject thank you for your time on this.
I do realise that in my stupidity I could have loaded the cm-11-20141112-SNAPSHOT-M12-honami.zip to my SD card (if I'd had one or waited and gotten one).
What I did however was wipe everything I possibly could, and then hit restore from sdcard/0/ I believe - it may have been a different directory.
I believe what I have done is restored to a blank image......
WHen not plugged into usb I get a red blinking LED when just pressing the power button once.
When holding volume-up + Power the phone vibrates as if it is trying to boot but is unable to
If I leave it plugged into USB AND then press , the device shows the sony Logo and then proceeds to display a backlit but plain black screen, Sony PC Companion recognises the device as connected but is unable to interact with it. The output of "adb devices" shows my device but says "unauthorized" and windows is attempting to install MTB driver....
The behaviour doesnt seem to be quite the same every time.
I believe the device is soft bricked.... is this likely to be a case of a wiped partition table? Or at least loss of the boot partition?
If I leave the device plugged in via USB it periodically reboots itself, shows the Sony logo, remains on a bank screen then shuts itself down.
Shows in device manager as "USB Input Device" on win 7 x64 pro
Thanks in advance
Pretty certain it's not hard bricked, there will be instructions here you can follow:
http://forum.xda-developers.com/showthread.php?t=2574764
Sent from my C6903 using XDA mobile app
D33KK said:
Pretty certain it's not hard bricked, there will be instructions here you can follow:
http://forum.xda-developers.com/showthread.php?t=2574764
Sent from my C6903 using XDA mobile app
Click to expand...
Click to collapse
I have done quite a lot of reading etc on the subject....
according to This thread, Sony Xperias have the bootloader in non-writable mask ROM... so you should always be able to access Fastboot or Flash Mode?
The problem I am having is that I don't seem to be able to activate EITHER Fastboot OR Flash mode in order to flash some new firmware onto my device....
My device is recognized as a "USB Input Device" on Device Manager and windows tries to install MTP driver. I'm going to have a go at the process with a fresh install of windows 7 x64 and 'windows auto-install drivers' turned off.
What is the maximum damage I could have done here?
Thanks
Update
Hard reset (red button inside of the sim-card slot) resets the phone with three vibrates and it restarts.
The phone powers on and displays Sony splash screen and then displays a back-lit black screen.
The phone gets much hotter than normal and powers on to the blank back-lit screen when on charge.
I have NO ACCESS to flash mode or fast boot. Any combination of buttons leads to the same outcome: single vibrate, red LED and the phone shows the Sony splash screen then blank screen, as if the button combinations are just ignored...
Flashtool DOES NOT recognize the device, although it is recognized as C6903 in device manager (I have Sony adb driver installed and have disabled the MTP driver that windows recommends).
Flashtool gives me the red error text about making sure drivers are installed and making sure the device isn't in MTP mode.
I'm at an absolute loss as to what to try next, can somebody shed any light on this? There are plenty of guides but they all seem to rely on EITHER fastboot or flash mode and I can access neither although the phone powers on!
Thanks in advance!
Maybe the partition was corrupted when you flash "blank" image..........
So....JTAG....or send to Sony service....
Shutdown with power+vol up (will vibrate thrice) and see if it doesn't turn on automatically.
If it didn't turn on now check your task manager on windows, go to process tab, kill adb.exe (every adb.exe)
Back on phone connect usb holding down the vol down button (phone have to be off before you connect usb), if green led turns on and doesn't turn off you are on flashmode.
Check on flashtool or flashtool64 (for 64bits) and see if flashtool detects your device. If it detects and recognizes your phone flash the FTF for your device and let it do its job.
As you messed the phone Sony will charge for repairs.

Can' access bootloader nor recovery...

Hi,
I have a major issue since the update to CM13.0-20160524-NIGHTLY-huashan. I litteraly spent the whole week trying everything I found on internet in order to solve it without success.
My problem is the following one: I uninstalled the gapps to manually update it for the latest version of Android (Android 6.0.1), when I tried to boot to the recovery nothing happened the phone just restart, same when trying to boot to the bootloader. I tried everything adb reboot recovery adb reboot bootloader, I tried flashtool, I used the developper options to reboot to recovery, I tried manually by holding the volume button while restarting, I tried the flashify application. Nothing, I am not able in anyway to access neither the recovery nor the bootloader. The phone is just restarting, the led is first blue then goes red then green then red and restart. However, I have a root shell on the phone with adb shell.
If anyone have a solution, can help me please do it. An Android phone without the gapps is quite useless.
Thank you very much,
same problem,my phone is now without working android (after i tried instal CyanogenMod 13.0 Unofficial SaberMod.....still loading cyanogenmod logo) and without working fastboot and recovery so im lost :/
Hello, since the LED bar lights up this means your device is soft bricked, in which, mostly are recoverable.
What interests me is that you tried to, quote, "uninstall gapps".. If you previously have gapps, you don't need to "uninstall" gapps in order to update to the next build. Just flash the new build zip and gapps will be preserved. Also I am quite skeptical about what you did, as I never heard of a way to actually uninstall gapps. Basically if someone wants to remove gapps, he needs to format the System partition and then flash the ROM zip again..
Are you sure you failed to boot into flashmode? the correct procedure to do so is
Make sure the device is turned off
Make sure the USB cable is connected to your PC
Hold the volume DOWN button
Still holding the button, insert the USB cable to the XSP
LED will light up green, indicating flashmode
But even so, since you are on an unlocked bootloader, recovering from this brick is rather easy.
Get yourself a TWRP img file from the TWRP basketbuild folder
Open flashtool
Make sure the device is turned off
Make sure the USB cable is connected to your PC
Hold the volume UP button
Still holding the button, insert the USB cable to the XSP
LED will light up blue, indicating fastboot mode
On flashtool, click the lightning icon and select fastboot mode
On the right of the new window that appears, select "Select kernel to flash"
Navigate to your TWRP img file and select it
When flash completes, unplug your XSP from the USB cable
This will flash TWRP into /boot partition. So when you start your device, it will go straight to recovery.
Now, flash the ROM zip
Thanks for your help TechnoSparks, however, as I told you and expected even following your exact procedure my phone just restart. The led brights up bleu for few seconds then the phone put itself in charging mode. And when I said I delete the gapps, I meant that I deleted the google play store from my phone (this app was anyway not working after update). I tried to use flashtool but it is the same, can't get into fastboot mode, the phone just normally starts or put itself in charge. Isn't a manual solution on how to flash a recovery only using adb shell?
AresS31 said:
Thanks for your help TechnoSparks, however, as I told you and expected even following your exact procedure my phone just restart. The led brights up bleu for few seconds then the phone put itself in charging mode. And when I said I delete the gapps, I meant that I deleted the google play store from my phone (this app was anyway not working after update). I tried to use flashtool but it is the same, can't get into fastboot mode, the phone just normally starts or put itself in charge. Isn't a manual solution on how to flash a recovery only using adb shell?
Click to expand...
Click to collapse
That seems to be related to your USB cable (since that is the famous issue). Can you try to charge your phone WITHOUT it stop charging (i mean suddenly the LED disappears and when you tap the screen the charging icon doesnt show)?
If it so does happens that your device doesnt want to charge, it seems to me that you are having a loose USB port which possibly from your XSP, or, your USB cable is no longer up for the challenge
You will need to find another reliable USB cable for you to try. Try to charge your XSP to see if that particular USB cable is reliable for you. Try to wiggle the wire a little bit, moving the XSP from different directions and see if it would still charge. If it still charge, then this is the USB cable for you to use. Do the mentioned steps above again.
If you insist and want to use the same USB cable, you will need to find a "sweet spot" so that the connection between your XSP and the USB cable will remain reliable.

Can't enter in flash mode

Hello to all,
I would like to install a custom ROM but unfortunately my phone doesn't want to enter in flash mode! Once switched off, I plug it to my computer while keeping vol down button pressed but instead of entering in flash mode, it displays the battery charging icon.
I hard reset the phone but the problem still remains. Any idea.
Thanks, have a nice day!
My guess is either the USB cable (did you use the OEM cable?) or the drivers (does windows recognize your phone?). Removing the SD card or first entering recovery were suggested earlier (http://forum.xda-developers.com/xperia-l/help/update-volume-connect-doesnt-t2613733). But more experiences Z3c owners may have better ideas...
Kholargol said:
Hello to all,
I would like to install a custom ROM but unfortunately my phone doesn't want to enter in flash mode! Once switched off, I plug it to my computer while keeping vol down button pressed but instead of entering in flash mode, it displays the battery charging icon.
I hard reset the phone but the problem still remains. Any idea.
Thanks, have a nice day!
Click to expand...
Click to collapse
Using flashtool:
Turn phone off completely.
Start flashtool, choose flashmode and choose which firmware you are going to use. Tick Exclude TA.. Click on flash.
It will start preparing the build and after a few seconds it will ask you to connect the phone.
Plug the phone in while holding volume down, as soon as flashtool starts doing something, you can let go.
If you don't know how to use flashtool then I urge caution, Sony's aren't like flashing a Samsung, it is actually possible to brick your phone with flashtool. There are lots of questions on 'how do I fix my phone?' in this Q&A thread from people who didn't read up on what they were doing.
Recommend you read bilboa1's great guide on what to do, starting with backing up your TA partition..
Thanks for your answers but I think the mini usb from my phone must be dead.
About Flashtool, I can't use it because I can't go into Flash mode! Moreover, my phone is not recognized by windows. I tried with several usb cables and computers when I plug it, I don't have any MTP or PTP choice, it can only charge..
On Windows 10, devices is not recognized and Window 7 see it as a 5880!
And I tried to remove SD and SIM cards..
Kholargol said:
Thanks for your answers but I think the mini usb from my phone must be dead.
About Flashtool, I can't use it because I can't go into Flash mode! Moreover, my phone is not recognized by windows. I tried with several usb cables and computers when I plug it, I don't have any MTP or PTP choice, it can only charge..
On Windows 10, devices is not recognized and Window 7 see it as a 5880!
And I tried to remove SD and SIM cards..
Click to expand...
Click to collapse
If the USB lead was dead you wouldn't get the charging icon on your phone.
Have you installed the Sony drivers.
You also need to run exe in the Drivers folder within Flashtool, to make sure you have correct flashomde drivers available. Installing these drivers is very difficult in Windows 10 and it require restarting the machine in safe mode, and going into the advanced settings to disable driver signature checking, this how to video is for windows 8, but you'll get the idea
Have you installed ADB?
Sonys PC Companion should set you up with the correct connection to your PC
Have you tried other USB cables?
Didgesteve said:
If the USB lead was dead you wouldn't get the charging icon on your phone.
Have you installed the Sony drivers.
You also need to run exe in the Drivers folder within Flashtool, to make sure you have correct flashomde drivers available. Installing these drivers is very difficult in Windows 10 and it require restarting the machine in safe mode, and going into the advanced settings to disable driver signature checking, this how to video is for windows 8, but you'll get the idea
Have you installed ADB?
Sonys PC Companion should set you up with the correct connection to your PC
Click to expand...
Click to collapse
Yes, I've installed PC Companion, adb drivers but nothing appears when I use command "adb devices". I've also installed flashtools drivers but deactivating drivers signatures in Windows. But when I try to flash, flashtool ask me to turn my device in flash mode (switch off then volume down + power) but I can't do that.
I've tried several usb cables. Some are charging my devices, some are aren't but none of them allows me to data transfer!
I've also tried to force MTP or PTP usb transfer in developper option, it doesn't work more..
Kholargol said:
Yes, I've installed PC Companion, adb drivers but nothing appears when I use command "adb devices". I've also installed flashtools drivers but deactivating drivers signatures in Windows. But when I try to flash, flashtool ask me to turn my device in flash mode (switch off then volume down + power) but I can't do that.
I've tried several usb cables. Some are charging my devices, some are aren't but none of them allows me to data transfer!
I've also tried to force MTP or PTP usb transfer in developper option, it doesn't work more..
Click to expand...
Click to collapse
Do you have any warranty on your phone, you could be right that the usb socket is damaged somehow, but it's strange that you can still get a charge through it.
Your only chance at moving to a custom rom change is flashfire
This should let you flash a rom without recovery.
Edit: Flashmode is just holding down just - volume button, not volume+power
Obviously your chances of rescuing a failed install are going to almost zero without recovery and flashtool, so be very very careful about what you try and flash in flashfire. Read up completely that the rom you want to flash is going to work pushed on top of whatever you are running at the moment.
For anyone who might be interested, sometimes you have to try a USB 2.0 port or just a different port. I had the same problem while using a usb 3 port, switched to 2.0 worked like a charm.
Try to open the back of the phone and removing/unplugging the battery wait 5 seconds and then put it in again. Then try holding down the volume down button while you connect a usb cable.
sir i have sony e3 dual and wanted to flash a custom rom . i connected it to pc but a
Ertert24 said:
Try to open the back of the phone and removing/unplugging the battery wait 5 seconds and then put it in again. Then try holding down the volume down button while you connect a usb cable.
Click to expand...
Click to collapse
sir i have sony e3 dual and wanted to flash a custom rom . i connected it to pc but after the original firmware was deleted i got to know that my phone volume down button isnt working. anyone please tell me how to put my phone in flashmode without pressing volume down button as it is not working

My Z2 Pro dead .. help me ..!!

i did something Stupid and my Z2 Pro dead
there is no fast-boot and no recovery .. only black screen and when i press power button there is a short and long vibration just that and the LED there is flash yellow for 0.1 second
aljthab said:
i did something Stupid and my Z2 Pro dead
there is no fast-boot and no recovery .. only black screen and when i press power button there is a short and long vibration just that and the LED there is flash yellow for 0.1 second[/QUOTE try connecting it to the PC, if it doesn't show anything on PC then just hand it over to the lenovo service center and blame it on the device that it stopped booting :silly:. I thought i had bricked my device but they did something and gave it to me in 3 to 4 days and that was done under the warranty no extra charge and don't confess that I had rooted ur device , If u tell them that they will try to extort money from u :crying:
Click to expand...
Click to collapse
aljthab said:
i did something Stupid and my Z2 Pro dead
e LED there is flash yellow for 0.1 second
Click to expand...
Click to collapse
I have exactly the same, what to do? I installed the dev 44, the rate of established but after 15 minutes, logo is stalled, not waiting until the end of excess freewheeling dev 300, it is not fully established and bug crawled, I rebooted the machine and an endless vibration with green LED :crying:
1 Charging can be a little warm
2. can not be detected pc
3. can not access the fastboot mode
4. when charging, the notification light dies
5. deep flash cable has not helped
sorry my bad english
kerei said:
I have exactly the same, what to do? I installed the dev 44, the rate of established but after 15 minutes, logo is stalled, not waiting until the end of excess freewheeling dev 300, it is not fully established and bug crawled, I rebooted the machine and an endless vibration with green LED :crying:
1 Charging can be a little warm
2. can not be detected pc
3. can not access the fastboot mode
4. when charging, the notification light dies
5. deep flash cable has not helped
sorry my bad english
Click to expand...
Click to collapse
Refer to this http://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/ and this http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-z2131-only.104/
same issue with zuk z2
adriano1593 said:
Refer to this http://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/ and this http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-z2131-only.104/
Click to expand...
Click to collapse
Hello there... Any solution you found? I am stuck with my zuk z2 in same situation ?? any help ?
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
m_atze said:
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
Click to expand...
Click to collapse
What id shown in unknown device.
Like ven_9102&dev_1234
Maybe with editing quallcom drivers for your device id, you can still install it.
and if luck qpst can recognize it as qualcomm debug mod
Sent from my ZUK Z2121 using Tapatalk
eryenakgun said:
What id shown in unknown device.
Like ven_9102&dev_1234
Maybe with editing quallcom drivers for your device id, you can still install it.
and if luck qpst can recognize it as qualcomm debug mod
Sent from my ZUK Z2121 using Tapatalk
Click to expand...
Click to collapse
Hi,
Thanks for your quick response.
The Hardware ID: USB\DEVICE_DESCRIPTOR_FAILURE
"Error Message": This device has been stopped because it has reported errors. (Code 43)
An error occurred while requesting the USB device descriptor.
m_atze said:
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
Click to expand...
Click to collapse
Alright bro, there is one method you can try.
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
I assume your phone is a brick now. The only method you can use is the 9008 unbrick mode. (AKA QBST)
There are a few things you need to prepare before you save ur phone. U need to download the require application that the website provided above, after you set everything up,
make sure you download the latest 2.5 QBST rom,
http://bbs.lenovomobile.cn/z2pro/t554654/
Because ur phone wont be able to enter 9008 through software, thus u need to do the following.
1. Load the content XML fille,
2.Turn off your phone. After it's fully shutdown
3. press and hold the volume up button for 3 seconds
4. press power button while hold the volume up (press it for 0.5second and keep holding it)
5. after 0.5 seconds, plug in the usb right away
6. the QFIL tool should appear the Qualcomm usb QD loader
7. the download button should turn blue
8. flash it and wait for reboot
OtakuLi said:
Alright bro, there is one method you can try.
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
I assume your phone is a brick now. The only method you can use is the 9008 unbrick mode. (AKA QBST)
There are a few things you need to prepare before you save ur phone. U need to download the require application that the website provided above, after you set everything up,
make sure you download the latest 2.5 QBST rom,
http://bbs.lenovomobile.cn/z2pro/t554654/
Because ur phone wont be able to enter 9008 through software, thus u need to do the following.
1. Load the content XML fille,
2.Turn off your phone. After it's fully shutdown
3. press and hold the volume up button for 3 seconds
4. press power button while hold the volume up (press it for 0.5second and keep holding it)
5. after 0.5 seconds, plug in the usb right away
6. the QFIL tool should appear the Qualcomm usb QD loader
7. the download button should turn blue
8. flash it and wait for reboot
Click to expand...
Click to collapse
Thanks for your tip.
I followed your described procedure, but the phone will not be recocnized by the PC.
1st: I loaded QFIL XML file. (By the way this tut is made by me)
2nd: I disconnected the battery (The phone can't be turned off normally!)
3rd, 4th, 5th
6th: nothing happend!
7th: "-"
8th: "-"
The only way the phone will detected by the PC:
1st: disconnect battery
2nd: plug in USB (PC and Phone)
3rd: press VOL+ or VOL- or PWR button (doesn't matter which one)
4th: connect battery
5th: detected as "unknown usb device (device descriptor request failed)"
m_atze said:
Thanks for your tip.
I followed your described procedure, but the phone will not be recocnized by the PC.
1st: I loaded QFIL XML file. (By the way this tut is made by me)
2nd: I disconnected the battery (The phone can't be turned off normally!)
3rd, 4th, 5th
6th: nothing happend!
7th: "-"
8th: "-"
The only way the phone will detected by the PC:
1st: disconnect battery
2nd: plug in USB (PC and Phone)
3rd: press VOL+ or VOL- or PWR button (doesn't matter which one)
4th: connect battery
5th: detected as "unknown usb device (device descriptor request failed)"
Click to expand...
Click to collapse
Make sure you have to plug in the usb right away as soon as you u press power, and keep holding them
OtakuLi said:
Make sure you have to plug in the usb right away as soon as you u press power, and keep holding them
Click to expand...
Click to collapse
Yes, I did exactly you described. Sorry but this isn't working.
I don't know what I should do. Even a repair shop couldn't fix it.
Maybe I need to do this:
http://bbs.lenovomobile.cn/z2/t121791/?highlight=900e
But I don't want to destroy my PC (3000 bugs)
m_atze said:
Yes, I did exactly you described. Sorry but this isn't working.
I don't know what I should do. Even a repair shop couldn't fix it.
Maybe I need to do this:
http://bbs.lenovomobile.cn/z2/t121791/?highlight=900e
But I won't destroy my PC (3000 bugs)
Click to expand...
Click to collapse
oh well, good luck
OtakuLi said:
oh well, good luck
Click to expand...
Click to collapse
I will report the result.
OK. I made the deepflash cable.
After using it there is no difference between pressing one of the button combinations I recently mentioned (VOL+ or VOL- or PWR).
The phone will be detected as Unknown device. After intalling my modified driver to match the unknown ID, QFIL don't detect the COM Port.
Hello had the same problem, only with the difference that my battery was not completely discharged.
What has helped:
1 Start QFIL Tool
2 Press the volume +
3 Connect the original cable to the PC
4 QFIL Tool recognized the phone and I could play an original Rome.
Mfg
Ps. Is now the battery cover (glass) broken?
No, I used a hairdryer, a razorblade, plastic tool and a suction cup to lift the backcover glass.
The glass is fully intact no damages.
You have good nerves. I would not have expected that.
But in the end, it does not matter if it does not start anymore.
Thank you again for your great instructions for playing and rooting the mobile phone.
I hope you get your phone back.
Mfg
Good and bad news
The guy unbricked the phone successfully, I received it today.
Now I have an other problem:
The phone is very very slow and laggy now.
The problem occurs everywere, Recovery, boot (the bootlogo laggs), booted System, also the test mode laggs now
Furthermore the sceen flickers sometimes and at the right side the sceen is mirrored sometimes.
Did anyone has an idea?
What I did today:
reflash through qfil
1.9.104_ST
2.3.044_ST
ZUI_2.5.335_ST
Hi m_atze, I am exactly in the same situation as You. After using deep flash cable method, I got "unknown usb device (device descriptor request failed)". Could You tell me what was the solution to unbrick the phone?

Categories

Resources