HTC One (M7) on T-Mobile Cant get Update - ROOTED - One (M7) Q&A, Help & Troubleshooting

Trying to go back to stock recovery to get the update for my HTC One M7, followed these directions (YOUTUBE LINK TO VIDEO: How to get OTA Updates on a rooted HTC One M8) and it still wont go through. Getting this message on boot (attached picture). Any ideas?
ok... cause I am new it wont let me post a picture or a link... Ill have to summarize what it says then. ...
E: Invalid command argument
E; Cant mount
I have to find a way to upload that picture...

alexk243 said:
Trying to go back to stock recovery to get the update for my HTC One M7, followed these directions (YOUTUBE LINK TO VIDEO: How to get OTA Updates on a rooted HTC One M8) and it still wont go through. Getting this message on boot (attached picture). Any ideas?
ok... cause I am new it wont let me post a picture or a link... Ill have to summarize what it says then. ...
E: Invalid command argument
E; Cant mount
I have to find a way to upload that picture...
Click to expand...
Click to collapse
To get OTA updates your phone must have stock rom, stock recovery, locked/relocked bootloader if S-ON and maybe some apps in the preload folder that were erased when you unlocked the phone. The quickest way is to run the RUU for your present version if it is 5.14.531.1 this is it. As I said earlier, if S-ON you have to lock your bootloader. If you need more help, please post a fastboot getvar all except for the imei and serialno.
Also, using a video for the M8 might not be the best since you have a M7.

Flash Recovery Error
So when I try to flash the stock recovery onto the phone in command prompt I get the following message:
sending recovery
okay
writing recovery
FAILED (remote: image update error)
Any idea why thats happening?

(bootloader) version: 0.5
(bootloader) version-bootloader: 1.55.0000
(bootloader) version-baseband: 4A.21.3263.03
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 3.24.531.3
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0713000
(bootloader) cidnum: T-MOB010
(bootloader) battery-status: good
(bootloader) battery-voltage: 4221mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-412e361e
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0

alexk243 said:
So when I try to flash the stock recovery onto the phone in command prompt I get the following message:
sending recovery
okay
writing recovery
FAILED (remote: image update error)
Any idea why thats happening?
Click to expand...
Click to collapse
Edit your post with the getvar all and remove the imei and serialno!
Which version of the stock recovery are you trying to update? Is it 3.24.531.3?
You are using these commands:
Code:
[B][I]fastboot flash recovery recovery.img
fastboot erase cache
fastboot reboot-bootloader[/I][/B]
You might also try the fastboot erase cache prior to and after the fastboot flash recovery recovery.img.

majmoz said:
Edit your post with the getvar all and remove the imei and serialno!
Which version of the stock recovery are you trying to update? Is it 3.24.531.3?
You are using these commands:
Code:
[B][I]fastboot flash recovery recovery.img
fastboot erase cache
fastboot reboot-bootloader[/I][/B]
You might also try the fastboot erase cache prior to and after the fastboot flash recovery recovery.img.
Click to expand...
Click to collapse
'
Yeah I edited it as soon as I posted it (minus the 5 min wait time on this site).
I was using 1.12.531.19 that I assumed was correct from my T-MOB010.... is that wrong?

alexk243 said:
'
Yeah I edited it as soon as I posted it (minus the 5 min wait time on this site).
I was using 1.12.531.19 that I assumed was correct from my T-MOB010.... is that wrong?
Click to expand...
Click to collapse
Yes, you should use 3.24.531.3 this is according to your version-main!

OK, Ill give that a shot. Should the update work with just the stock ROM or is there other stuff I have to convert back to stock as well?

alexk243 said:
OK, Ill give that a shot. Should the update work with just the stock ROM or is there other stuff I have to convert back to stock as well?
Click to expand...
Click to collapse
Here is what the OTA is looking for: http://forum.xda-developers.com/showpost.php?p=52894276&postcount=9
And here is how to manually install an OTA.

Updates Worked
Ok, Updates worked and I had more than one waiting it seems. That was it, was just using the wrong stock recovery.
Now it looks like i have lost my root... going to re-flash CWM recovery and see if that helps... if not I am not sure. SU says it no longer has root privilege. Do I have to totally redo rooting?

Related

[Q] No android, no recovery, only bootloader... :(

Dear XDA,
I wanted to update my HTC One to Revolution HD. But there where some requirements before i could install that. Like updating the firmware and installing TWRP recovery. I needed to RELOCK my phone in order to update my firmware. So i did that using a tutorial. After that i only had to push the RUU and i would be back @ stock. And then i could flash Revolution HD to get 4.4!
But!... it went horribly wrong. As of right now, i can only enter fastboot. I cannot enter recovery, and there is no Android installed, so basically i'm screwed.
I do have some flashing experience and I'm not a complete newb, but this is out of my league. Perhaps there are some nice persons here that could help me out. I will try to summarise my phone settings:
My current settings in Fastboot:
M7_UL PVT SHIP S-ON RH
HBOOT-1.44.0000
RADIO-4A.14.3250.13
OpenDSP-v26.120.274.0202
eMMC-boot
May 3 2013,17:22:59:-1
CID: HTC_E11
MID: PN0710000
I have a nandroidback, but i can't get into recovery. I tried using ADB but my device is not recognised.... I get the feeling that S-ON needs to change to S-OFF. But if i use a toolkit (from Squabbi) i can't get my device S-OFF (device not recognised..).
As of right now, I'm sitting with my hands in my hair thinking i bricked my phone.
If someone could help me, you would save my day.
Lennard Breevaart.
ps: I'm using windows xp
len.asdf said:
Dear XDA,
I wanted to update my HTC One to Revolution HD. But there where some requirements before i could install that. Like updating the firmware and installing TWRP recovery. I needed to RELOCK my phone in order to update my firmware. So i did that using a tutorial. After that i only had to push the RUU and i would be back @ stock. And then i could flash Revolution HD to get 4.4!
But!... it went horribly wrong. As of right now, i can only enter fastboot. I cannot enter recovery, and there is no Android installed, so basically i'm screwed.
I do have some flashing experience and I'm not a complete newb, but this is out of my league. Perhaps there are some nice persons here that could help me out. I will try to summarise my phone settings:
My current settings in Fastboot:
M7_UL PVT SHIP S-ON RH
HBOOT-1.44.0000
RADIO-4A.14.3250.13
OpenDSP-v26.120.274.0202
eMMC-boot
May 3 2013,17:22:59:-1
CID: HTC_E11
MID: PN0710000
I have a nandroidback, but i can't get into recovery. I tried using ADB but my device is not recognised.... I get the feeling that S-ON needs to change to S-OFF. But if i use a toolkit (from Squabbi) i can't get my device S-OFF (device not recognised..).
As of right now, I'm sitting with my hands in my hair thinking i bricked my phone.
If someone could help me, you would save my day.
Lennard Breevaart.
ps: I'm using windows xp
Click to expand...
Click to collapse
is your bootloader unlocked ? do that first
what version of TWRP do you have (exact name)
do you have fastboot/adb on your pc and do you know how to use them ?
is your bootloader unlocked ? do that first
==> I think so, how can i check?
what version of TWRP do you have (exact name)
==> I have no recovery installed on my phone. But i have TWRP version 2.6.3.3. img on my computer, ready to push it to my phone (but it gives the error: device not found)
do you have fastboot/adb on your pc and do you know how to use them ?
==> I think i do. When i try to do adb shell in command window it replies with either device not found, or adb server out of date. Killing...
Thanks for replying btw!
len.asdf said:
is your bootloader unlocked ? do that first
==> I think so, how can i check?
what version of TWRP do you have (exact name)
==> I have no recovery installed on my phone. But i have TWRP version 2.6.3.3. img on my computer, ready to push it to my phone (but it gives the error: device not found)
do you have fastboot/adb on your pc and do you know how to use them ?
==> I think i do. When i try to do adb shell in command window it replies with either device not found, or adb server out of date. Killing...
Thanks for replying btw!
Click to expand...
Click to collapse
take these files
extract fastboot.zip to c:\fastboot
and install these drivers
http://www.mediafire.com/download/j55vk6qbbr6250c/HTCDriver_4.8.0.002.exe
MD5: e2a21d71954d4164c1a116abb926a363
and see if you can get:
fastboot getvar all
and post the results minus you serial no and IEMI
clsA said:
take these files
extract fastboot.zip to c:\fastboot
and install these drivers
http://www.mediafire.com/download/j55vk6qbbr6250c/HTCDriver_4.8.0.002.exe
MD5: e2a21d71954d4164c1a116abb926a363
and see if you can get:
fastboot getvar all
and post the results minus you serial no and IEMI
Click to expand...
Click to collapse
Thanks! This is what i did to get my results:
1. Downloaded both the fastboot.zip and the drivers (and installed ofcourse).
2. Opened a command window on c:\fastboot
3. typed: fastboot getvar all
Results:
C:\fastboot>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.44.0000
(bootloader) version-baseband: 4A.14.3250.13
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 1.29.401.16
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: -
(bootloader) imei: -
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0710000
(bootloader) cidnum: HTC__E11
(bootloader) battery-status: good
(bootloader) battery-voltage: 4222mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
getvar:all FAILED (status read failed (Too many links))
finished. total time: 0.047s
C:\fastboot>
len.asdf said:
Thanks! This is what i did to get my results:
1. Downloaded both the fastboot.zip and the drivers (and installed ofcourse).
2. Opened a command window on c:\fastboot
3. typed: fastboot getvar all
Results:
C:\fastboot>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.44.0000
(bootloader) version-baseband: 4A.14.3250.13
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 1.29.401.16
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: -
(bootloader) imei: -
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0710000
(bootloader) cidnum: HTC__E11
(bootloader) battery-status: good
(bootloader) battery-voltage: 4222mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
getvar:all FAILED (status read failed (Too many links))
finished. total time: 0.047s
C:\fastboot>
Click to expand...
Click to collapse
Your phone is basically still stock andriod version 4.1.2
(this is good you can s-off pretty easy)
what RUU were you going to flash ?
this is the version of recovery you need
http://techerrata.com/browse/twrp2/m7ul
download it and put it in your fastboot folder
then to flash it:
fastboot flash recovery openrecovery-twrp-2.6.3.4-m7ul.img
fastboot erase cache
fastboot reboot-bootloader
now you can enter recovery correct ?
clsA said:
Your phone is basically still stock andriod version 4.1.2
(this is good you can s-off pretty easy)
what RUU were you going to flash ?
Click to expand...
Click to collapse
The RUU i tried was this one: RUU M7 U JB 50 HTC Europe 1.29.401.2 R Radio 4A.14.3250.13 10.33.1150.01 Release 311663 Signed 2 4
(from: http://forum.xda-developers.com/showthread.php?t=2428276)
While installing the RUU it gave me an an error that my CID and MID didn't match.
clsA said:
Your phone is basically still stock andriod version 4.1.2
(this is good you can s-off pretty easy)
what RUU were you going to flash ?
this is the version of recovery you need
http://techerrata.com/browse/twrp2/m7ul
download it and put it in your fastboot folder
Click to expand...
Click to collapse
Downloaded the recovery and put in the the fastboot folder
clsA said:
Your phone is basically still stock andriod version 4.1.2
(this is good you can s-off pretty easy)
what RUU were you going to flash ?
this is the version of recovery you need
http://techerrata.com/browse/twrp2/m7ul
download it and put it in your fastboot folder
then to flash it:
fastboot flash recovery openrecovery-twrp-2.6.3.4-m7ul.img
fastboot erase cache
fastboot reboot-bootloader
now you can enter recovery correct ?
Click to expand...
Click to collapse
While in ADB it gave this error:
C:\fastboot>fastboot flash recovery openrecovery-twrp-2.6.3.4-m7ul.img
sending 'recovery' (9840 KB)...
OKAY [ 1.297s]
writing 'recovery'...
(bootloader) signature checking...
FAILED (remote: signature verify fail)
finished. total time: 1.891s
C:\fastboot>
edit: I cannot enter recovery yet. Just tried it
len.asdf said:
While in ADB it gave this error:
C:\fastboot>fastboot flash recovery openrecovery-twrp-2.6.3.4-m7ul.img
sending 'recovery' (9840 KB)...
OKAY [ 1.297s]
writing 'recovery'...
(bootloader) signature checking...
FAILED (remote: signature verify fail)
finished. total time: 1.891s
C:\fastboot>
edit: I cannot enter recovery yet. Just tried it
Click to expand...
Click to collapse
your bootloader is still locked
clsA said:
your bootloader is still locked
Click to expand...
Click to collapse
I checked the md5 (f428caf36c9c337e2ae417fc10fbe165) with the file i downloaded. And it matches
len.asdf said:
I checked the md5 (f428caf36c9c337e2ae417fc10fbe165) with the file i downloaded. And it matches
Click to expand...
Click to collapse
yeah i realize that your bootloader is still locked
you need to go to htcdev and unlock again
then flash recovery
clsA said:
yeah i realize that your bootloader is still locked
you need to go to htcdev and unlock again
Click to expand...
Click to collapse
Ah ok, I will be doing that then . I will update this topic when i'm done.
len.asdf said:
Ah ok, I will be doing that then . I will update this topic when i'm done.
Click to expand...
Click to collapse
be warned unlocking will wipe the phone you'll be starting from nothing
clsA said:
be warned unlocking will wipe the phone you'll be starting from nothing
Click to expand...
Click to collapse
I know! But don't worry, it's the least of my problems now
Unlocked my phone, and gonna flash the recovery aswell!
But to not make the same mistake twice. What is the best way to update my phone to 4.4?
I wanted to install Revolution HD. But maybe you have a better alternative?
And how can i properly thank you? I mean, you just saved my ass!
len.asdf said:
And how can i properly thank you? I mean, you just saved my ass!
Click to expand...
Click to collapse
it's no problem
you should try and get s-off next
http://forum.xda-developers.com/showthread.php?t=2314582 - revone
ARHD is great .. I also use ViperOne
just use the sideload feature in twrp being your phone is wiped
Quote:
Set the device into ADB sideload mode. In TWRP you do this by going to Advanced then ADB Sideload.
From the command line, type adb sideload name_of_rom.zip
or
adb push Rom.zip /data/media/0/
Click to expand...
Click to collapse
clsA said:
it's no problem
you should try and get s-off next
http://forum.xda-developers.com/showthread.php?t=2314582 - revone
ARHD is great .. I also use ViperOne
just use the sideload feature in twrp being your phone is wiped
Click to expand...
Click to collapse
I will get s-off through the HTC One All in one toolkit. But on the ARHD topic, this was posted aswell:
You need:
HTC One unlocked with htcdev.com (S-ON) or S-OFF
Custom recovery
Firmware package from here (recommended but not needed for now)
Read this flashing guide - [GUIDE] Complete Flashing Guide | Rooting | Going Back To Stock
So i tried to get the latest firmware, and that's where the problems started. But shouldn't it be better to have the latest firmware? I mean it stands there for a reason, right? Or am I wrong?
Anyway, i will try ARHD for now, it looks nice
Thanks again!
len.asdf said:
I will get s-off through the HTC One All in one toolkit. But on the ARHD topic, this was posted aswell:
You need:
HTC One unlocked with htcdev.com (S-ON) or S-OFF
Custom recovery
Firmware package from here (recommended but not needed for now)
Read this flashing guide - [GUIDE] Complete Flashing Guide | Rooting | Going Back To Stock
So i tried to get the latest firmware, and that's where the problems started. But shouldn't it be better to have the latest firmware? I mean it stands there for a reason, right? Or am I wrong?
Anyway, i will try ARHD for now, it looks nice
Thanks again!
Click to expand...
Click to collapse
firmware comes after s-off
and ARHD 31.6 is your best bet for now till your s-off

Need help with htc one!

hello,
so i recently accidentally removed my android OS from my htc one (m7) and the backup i took , and now im stuck with a bricked phone.
it is still unlocked , S-on however and i have the Twrp custom recovery.
I have the stock RUU for my phone but i can't use ADB push command to forward it to my phone.
It might be because my usb debugging is off ( probably not ) but i cant open my phone , it keeps stuck at the bootscreen.
i also couldnt flash it with fasboot flash zip command.
If anyone could help me out with this, i would be so happy.
Thanks in advance
angizwa said:
hello,
so i recently accidentally removed my android OS from my htc one (m7) and the backup i took , and now im stuck with a bricked phone.
it is still unlocked , S-on however and i have the Twrp custom recovery.
I have the stock RUU for my phone but i can't use ADB push command to forward it to my phone.
It might be because my usb debugging is off ( probably not ) but i cant open my phone , it keeps stuck at the bootscreen.
i also couldnt flash it with fasboot flash zip command.
If anyone could help me out with this, i would be so happy.
Thanks in advance
Click to expand...
Click to collapse
What RUU are you trying to flash? Here is alray's procedure for your situation. You might want to check the prerequisites on installed drivers. Also, is there a RUU.exe file to use instead of a zip file?
If these procedures don't work, then post a fastboot getvar all except for the imei and serialno.
@majmoz
The ruu im using is a zip ( i used it before and it works, ) its the guru reset M7 3.62.401.1, my drivers work too , it recognizes my phone when plugged into my pc
here is my getvar
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.57.0000
(bootloader) version-baseband: 4T.27.3218.14
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0710000
(bootloader) cidnum: HTC__E11
(bootloader) battery-status: good
(bootloader) battery-voltage: 4070mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-e47fb74b
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.165s
angizwa said:
@majmoz
The ruu im using is a zip ( i used it before and it works, ) its the guru reset M7 3.62.401.1, my drivers work too , it recognizes my phone when plugged into my pc
here is my getvar
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.57.0000
(bootloader) version-baseband: 4T.27.3218.14
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0710000
(bootloader) cidnum: HTC__E11
(bootloader) battery-status: good
(bootloader) battery-voltage: 4070mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-e47fb74b
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.165s
Click to expand...
Click to collapse
angizwa said:
hello,
so i recently accidentally removed my android OS from my htc one (m7) and the backup i took , and now im stuck with a bricked phone.
it is still unlocked , S-on however and i have the Twrp custom recovery.
I have the stock RUU for my phone but i can't use ADB push command to forward it to my phone.
It might be because my usb debugging is off ( probably not ) but i cant open my phone , it keeps stuck at the bootscreen.
i also couldnt flash it with fasboot flash zip command.
If anyone could help me out with this, i would be so happy.
Thanks in advance
Click to expand...
Click to collapse
guru reset M7 3.62.401.1 is not a RUU, its a ROM (stock rom) and must be installed using a custom recovery, not using "fastboot flash zip" command which is only used to flash RUU.zip or Firmware.zip
However, 3.62.401.1 is no longer the version you need (your hboot is 1.57) so you probably need the 5.11.401.10 or 6.09.401.5 rom.
Also usb debugging have nothing to do with using adb from custom recovery, its only to enable adb when booted in the OS.
make sure to use twrp 2.6.3.3 with latest adb 1.0.31 and latest htc drivers installed and push the correct stock rom to your phone using adb push or sideload.
@alray
oohh okay thanks, ill get that twrp, but do i have to change twrp version ? mine is 2.7-something, i'll download the correct ruu... i feel so stupid right now thanks, i really hope this works
angizwa said:
@alray
oohh okay thanks, ill get that twrp, but do i have to change twrp version ? mine is 2.7-something, i'll download the correct ruu... i feel so stupid right now thanks, i really hope this works
Click to expand...
Click to collapse
There is no RUU you can flash for that version with s-on. Find a stock rom for your version. And better to use twrp 2.6.3.3
Sent from my HTC One using XDA Free mobile app
you can sideload a rom through adb while you're in twrp super easy and fast
@alray
oh okay ill look for a stock rom then
@2B_4G10
i know i tried sideload and push, but for some reason ADB doesnt want to work
i typed adb devices in command and it did show an empty list, no idea why...
hmm i tried flashing the stock rom,
i got this error
http://i.imgur.com/XzOOJYE.jpg
what does this mean ?
oh and after relocking, it gave me a signature check (remote : 12 ) fail... :/
angizwa said:
hmm i tried flashing the stock rom,
i got this error
http://i.imgur.com/XzOOJYE.jpg
what does this mean ?
oh and after relocking, it gave me a signature check (remote : 12 ) fail... :/
Click to expand...
Click to collapse
look back at post #4, already explained why
@alray
oh... so its not a stock rom ? adb doesnt work on my device anymore... adb devices gives me an empty list...
and i cant flash the other TWRP version ... it gives me this problem :
target reported max download size of 1514139648 bytes
sending 'customrecovery' (10854 KB)...
OKAY [ 1.767s]
writing 'customrecovery'...
(bootloader) signature checking...
FAILED (remote: signature verify fail)
finished. total time: 2.709s
angizwa said:
@alray
oh... so its not a stock rom ?
Click to expand...
Click to collapse
Only RUU (Rom Update Utility) can be flashed with fastboot flash zip commands, not ROM even if the rom is a STOCK rom. RUUs and ROMS are 2 differents things. The RUU is a package containing the system(ROM), kernel, radio, bootloader, touch screen drivers and much more. It must be signed with HTC encrypted key to be flashed using "fastboot flash zip"
A ROM is a package including the system (/system) and the kernel (boot.img) and MUST be flashed from custom recovery, even if its a stock rom (like a guru reset rom or a stock odexed rom)
adb doesnt work on my device anymore... adb devices gives me an empty list...
Click to expand...
Click to collapse
Probably because your drivers are not installed correctly. this can be verified from Windows device manager. When the phone is booted in recovery, check that the phone is listed as a "android ADB interface".
and i cant flash the other TWRP version ... it gives me this problem :
target reported max download size of 1514139648 bytes
sending 'customrecovery' (10854 KB)...
OKAY [ 1.767s]
writing 'customrecovery'...
(bootloader) signature checking...
FAILED (remote: signature verify fail)
finished. total time: 2.709s
Click to expand...
Click to collapse
FAILED (remote: signature verify fail) = Locked or Relocked bootloader, you must have an unlocked bootloader to flash recovery.
@angizwa follow procedure linked at post #2
nope, no android ADB in my driver list when in recovery oO , but i can see android usb devices when in fastboot... i guess i have the wrong drivers... ill see if i can find them, i really hope that was the problem oO
angizwa said:
hmm i tried flashing the stock rom,
i got this error
http://i.imgur.com/XzOOJYE.jpg
what does this mean ?
oh and after relocking, it gave me a signature check (remote : 12 ) fail... :/
Click to expand...
Click to collapse
you flash roms with custom recovery (TWRP) not with fastboot. Why did you relock the bootloader ? unlock it reflash TWRP 2.6.3.3 then sideload / Push the rom
TWRP / Advanced / ADB Sideload - swipe to sideload
From PC adb / fastboot folder
you use
adb sideload name-of-rom.zip
make sure the rom is in the same folder as adb / fastboot
@clsA
yes i tried sideload before, but as i said, my adb doesnt work... adb devices does show me an empty list ...
angizwa said:
@clsA
yes i tried sideload before, but as i said, my adb doesnt work... adb devices does show me an empty list ...
Click to expand...
Click to collapse
Then you need to fix your drivers
see post 2 of the superguide
http://forum.xda-developers.com/showthread.php?t=2541082
@clsA
ok thanks, ill try fixing them

[Q] Htc One M7- deleted operating system. Relocked bootloader

Hi guys,
I have a big problem with my HTC One. I wanted to give it to the service, but it costs a lot of money, maybe I will find some help on XDA hopefully.
My bootloader info looks like this:
*** TAMPERED ***
*** UNLOCKED ***
M7_UL PVT SHIP S-ON RH
HBOOT- 1.57.0000
RADIO- 4T.27.3218.14
OpenDSP-v32.120.274.0909
OS-5.11.401.10
eMMC-boot 2048MB
May 5 2014,23:16:29.0
I deleted my system partition in twrp recovery. I can get only to bootloader and recovery. I am S-ON all the time, cannot get S-OFF, I get errors all the time using rum runner or firewater. When I type fastboot oem lock, I am stuck in bootloader, cannot enter recovery. Then the bootloader says ***TAMPERED*** ***RELOCKED*** ***SECURITY WARNING***. I really don't know what to do, I'm stuck. Please help :C !!!
Thanks
My fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.57.0000
(bootloader) version-baseband: 4T.27.3218.14
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 5.11.401.10
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno:
(bootloader) imei:
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0710000
(bootloader) cidnum: HTC__032
(bootloader) battery-status: good
(bootloader) battery-voltage: 4332mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-e47fb74b
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.099s
GalaXxXx said:
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.57.0000
(bootloader) version-baseband: 4T.27.3218.14
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 5.11.401.10
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: removed
(bootloader) imei: removed
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0710000
(bootloader) cidnum: HTC__032
(bootloader) battery-status: good
(bootloader) battery-voltage: 4332mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-e47fb74b
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.099s
Click to expand...
Click to collapse
You should remove your imei and serialno in your previous post. You can use this stock rom zip to go back to stock. It is the same version that you have. Your bootloader must be LOCKED or RELOCKED. Move the file to your adb/fastboot folder and rename it rom.zip. Open a command window on the same folder then type the following:
Code:
[B][I]adb reboot bootloader[/I][/B]
After that, type:
Code:
[B][I]fastboot oem rebootRUU [/I][/B]
NOTE: You should see a silver HTC logo come up on your phone after executing this command.
NOTE: if this command freezes, just disconnect the USB cable and hold the power and volume down buttons until the device reboots. Then, repeat the steps above again.
Finally:
Code:
[B][I]fastboot flash zip rom.zip[/I][/B]
Repeat the same command: IMPORTANT
Code:
[B][I]fastboot flash zip rom.zip[/I][/B]
NOTE: The green bar on the phone may not go to 100% of the bar ... but If you see completed on your computer command window, wait for a few seconds and move on.
Last Step:
Code:
[B][I]fastboot reboot[/I][/B]
Click to expand...
Click to collapse
Thanks a lot @majmoz
I'm downloading zip file now (slow internet 2 hours remaining). I will try your method, and let you know how it went.
doesn't work ;/
@majmoz , it doesn't work .
I did everything you said and when flashing it says "FAILED (remote: 12 signature verify fail)". Did this command 2 times as you instructed.
The second thing is that the "adb reboot bootloader" command didn't work, cmd said that device not found.
What should I do ?
GalaXxXx said:
@majmoz , it doesn't work .
I did everything you said and when flashing it says "FAILED (remote: 12 signature verify fail)". Did this command 2 times as you instructed.
The second thing is that the "adb reboot bootloader" command didn't work, cmd said that device not found.
What should I do ?
Click to expand...
Click to collapse
Does you bootloader still say "Relocked"? Let try to run the stock firmware 5.11.401.10 using the same method, just rename the download to firmware.zip change the rom.zip in the procedure to firmware.zip.
For adb not working take a look at FAQ Q#2.
My bootloader says TAMPERED RELOCKED SECURITY WARNING
I don't think adb works in bootloader, right ?
The firmware.zip worked, (there was the green bar etc.), but the phone is still not rebooting into system.
hmm... there is no custom recovery anymore, just a phone with red sign. And in bootloader it says only tampered and relocked. Without security warning. @majmoz
GalaXxXx said:
My bootloader says TAMPERED RELOCKED SECURITY WARNING
I don't think adb works in bootloader, right ?
The firmware.zip worked, (there was the green bar etc.), but the phone is still not rebooting into system.
hmm... there is no custom recovery anymore, just a phone with red sign. And in bootloader it says only tampered and relocked. Without security warning. @majmoz
Click to expand...
Click to collapse
You are correct adb does not work in bootloader. When the firmware completed it installed the stock recovery. Since you erased the system partition there is no OS installed. You can try to run the RUU again and it will probably pass now since you have the correct firmware. If this is successful, you will have stock rom and stock firmware on your phone.
What did you mean by give to service?
majmoz said:
You are correct adb does not work in bootloader. When the firmware completed it installed the stock recovery. Since you erased the system partition there is no OS installed. You can try to run the RUU again and it will probably pass now since you have the correct firmware. If this is successful, you will have stock rom and stock firmware on your phone.
What did you mean by give to service?
Click to expand...
Click to collapse
There is an unbrick service here in the forum
I would imagine that's what he's referring to
You are correct adb does not work in bootloader. When the firmware completed it INSTALLED the stock recovery. Since you erased the system partition there is no OS installed. You can try to run the RUU again and it will probably pass now since you have the correct firmware. If this is successful, you will have stock rom and stock firmware on your phone.
What did you mean by give to service?
Click to expand...
Click to collapse
There is an unbrick service here in the forum
I would imagine that's what he's referring to
Click to expand...
Click to collapse
No no, I have a service nearby here in my town. They said they can restore the phone for $30.
I will try the RUU file now, hope it works. I'll be informing what is the status of my "operation" @majmoz @ajbiz11
P.S. How to quote ? You know (Originally Posted by etc.)
GalaXxXx said:
I did everything you said and when flashing it says "FAILED (remote: 12 signature verify fail)".
Click to expand...
Click to collapse
@majmoz I don't think this zip can be flashed using "fastboot flash zip rom.zip", with s-on he can only flash signed ruu from HTC and afaik, htc never released any 5.11.401.10 signed ruu
There is a flashable aroma zip (guru reset) for his version here: https://www.androidfilehost.com/?fid=23501681358543706
to be flashed with a custom recovery (require to unlock the bootloader again)
Yeah @alray , I need to have a 5.11.401.10 signed RUU, but there is no such file avaible to download.
Now, I will unlock my bootloader again, flash custom recovery (TWRP) , and try flash guru reset in this recovery.
Well, I don't really remember, but I think I tried this (maybe with not the same version of guru reset), but I was stuck on "Installation procces" It was 0 % all the time. Let's see how it works out this time with this version of guru.
@alray
I unlocked my bootloader, flashed TWRP, I used adb to push the .zip to sdcard, but the problem now is that the phone says that unable to mount '/data' and unable to mount internal storage. When I click mount in recovery the "data" box doesn't wanna tick .
What should I do ? I'm tired of this ...
Ok, what happened next... I finally did what @alray told me to do. I managed to fix the corrupted data partition, but as I said earlier, when I flash the guru reset in recovery, and start the installation process, it is stuck on 0.00%.
I unlocked the bootloader in order to do this.
No more ideas ? @majmoz ?
GalaXxXx said:
Ok, what happened next... I finally did what @alray told me to do. I managed to fix the corrupted data partition, but as I said earlier, when I flash the guru reset in recovery, and start the installation process, it is stuck on 0.00%.
I unlocked the bootloader in order to do this.
No more ideas ? @majmoz ?
Click to expand...
Click to collapse
What version of TWRP are you using? 2.6.3.3 or 2.8.0.1? I'm pretty sure you checked the MD5 of the files you downloaded.
I'm using TWRP v2.8.0.2. What do you mean by saying you're pretty sure I checked the MD5? I didn't .. @majmoz
GalaXxXx said:
I'm using TWRP v2.8.0.2. What do you mean by saying you're pretty sure I checked the MD5? I didn't .. @majmoz
Click to expand...
Click to collapse
You should always check the MD5 of downloaded files to ensure they did not get corrupted during the downloading process. The MD5 is generally noted on the download site. Here is a how to check the MD5.
I also recommend to use 2.6.3.3 instead of 2.8+
Ohh my god, finally did it !!! Thank you a lot guys !!! I was trying guru reset earlier with unlocked bootloader too, but the twrp version was wrong... ohh, everything because of this new version of twrp.... But thanks, I have my system back . I will be able to do OTA updates now ?
 @majmoz @alray
GalaXxXx said:
Ohh my god, finally did it !!! Thank you a lot guys !!! I was trying guru reset earlier with unlocked bootloader too, but the twrp version was wrong... ohh, everything because of this new version of twrp.... But thanks, I have my system back . I will be able to do OTA updates now ?
@majmoz @alray
Click to expand...
Click to collapse
you should be able to do ota if you have selected to install stock recovery in the aroma installer.

[Q] From custom to stock, need help plz !

Hello there !
I got a prolem with my htc one international.
For a while i had a custom rom and decided to go back to stock rom. After some time trying to go back to stock i got som problems now.
i had TWRP on the phone, and i flashed another recovery.img, now my recovery looks all weird. i'll attach a screenshot from.
Now i cant get my old recovery i have tried everything. is there anybody out there to help me !!
(on the image you can see how it looks after trying an OTA installation)
Dardo27 said:
Hello there !
I got a prolem with my htc one international.
For a while i had a custom rom and decided to go back to stock rom. After some time trying to go back to stock i got som problems now.
i had TWRP on the phone, and i flashed another recovery.img, now my recovery looks all weird. i'll attach a screenshot from.
Now i cant get my old recovery i have tried everything. is there anybody out there to help me !!
(on the image you can see how it looks after trying an OTA installation)
Click to expand...
Click to collapse
Nearly every thread in this section has something to do with not being able to update from kitkat to lollipop on rooted phone.
did you read any of those and try anything before asking for help ?
you make no mention of what phone you have
you need a stock system and stock recovery to take OTA updates have you flash a stock rom before the stock recovery ?
clsA said:
Nearly every thread in this section has something to do with not being able to update from kitkat to lollipop on rooted phone.
did you read any of those and try anything before asking for help ?
you make no mention of what phone you have
you need a stock system and stock recovery to take OTA updates have you flash a stock rom before the stock recovery ?
Click to expand...
Click to collapse
Sure i do mention what phone i have, HTC one m7 !!! and u can see the pic !
i have read many posts on the internet, tried a lot to go back to stock, am on stock right now, the only problem is my recovery mode !
Dardo27 said:
Sure i do mention what phone i have, HTC one m7 !!! and u can see the pic !
Click to expand...
Click to collapse
There is many versions of the M7. You need to post the output of "fastboot getvar all" like we ask in every threads here so we can know exactly what phone you have and which sofmtware/firmware version installed, CID and MID number, S-ON or S-OFF.
i have read many posts on the internet, tried a lot to go back to stock, am on stock right now, the only problem is my recovery mode !
Click to expand...
Click to collapse
What recovery version have you flashed exactly?
Waiting for your "fastboot getvar all" output (remove imei and serialno befor eposting).
Dardo27 said:
Sure i do mention what phone i have, HTC one m7 !!! and u can see the pic !
i have read many posts on the internet, tried a lot to go back to stock, am on stock right now, the only problem is my recovery mode !
Click to expand...
Click to collapse
start by making sure you have the correct stock recovery, look wrong to me, so have a look through the general section for a thread labelled "stock recovery collection" and then download the 6.09.401.11 (your firmware) recovery and flash it, then try and update again.
alray said:
There is many versions of the M7. You need to post the output of "fastboot getvar all" like we ask in every threads here so we can know exactly what phone you have and which sofmtware/firmware version installed, CID and MID number, S-ON or S-OFF.
What recovery version have you flashed exactly?
Waiting for your "fastboot getvar all" output (remove imei and serialno befor eposting).
Click to expand...
Click to collapse
Here you go !
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.57.0000
(bootloader) version-baseband: 4T.29.3218.08
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 6.09.401.11
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno:
(bootloader) imei:
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0710000
(bootloader) cidnum: HTC__Y13
(bootloader) battery-status: good
(bootloader) battery-voltage: 4067mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-6d8a0b9b
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
I do not exactly remember what version of recovery it was, but i think was a stockrecovery with the wrong version from what i need!
i locked my bootloader and have no root anymore !!
thank u for your help !
Dardo27 said:
Here you go !
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.57.0000
(bootloader) version-baseband: 4T.29.3218.08
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 6.09.401.11
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno:
(bootloader) imei:
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0710000
(bootloader) cidnum: HTC__Y13
(bootloader) battery-status: good
(bootloader) battery-voltage: 4067mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-6d8a0b9b
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
I do not exactly remember what version of recovery it was, but i think was a stockrecovery with the wrong version from what i need!
i locked my bootloader and have no root anymore !!
thank u for your help !
Click to expand...
Click to collapse
you must use the 6.09.401.11 stock recovery. Since you have re-locked the bootloader, you'll have to unlock it again, restore the stock rom again and then flash the 6.09.40.11 stock recovery so you can use ota updates. No need to relock the bootloader
6.09.401.11 stock recovery here: https://www.androidfilehost.com/?fid=95832962473395870
6.09.401.11 twrp nandroid backup here: https://www.androidfilehost.com/?fid=95832962473396067
Seanie280672 said:
start by making sure you have the correct stock recovery, look wrong to me, so have a look through the general section for a thread labelled "stock recovery collection" and then download the 6.09.401.11 (your firmware) recovery and flash it, then try and update again.
Click to expand...
Click to collapse
i have tried that, this is what i get " (bootloader) signature checking...
FAILED (remote: signature verify fail)"
dont know if i'm using the right method for flash.
Dardo27 said:
i have tried that, this is what i get " (bootloader) signature checking...
FAILED (remote: signature verify fail)"
dont know if i'm using the right method for flash.
Click to expand...
Click to collapse
Failed to flash cos your bootloader is re-locked.
See @alray post above, you will have to start again, you dont need to lock or re-lock the bootloader for an OTA.
Fingerprint error as per your picture is a firmware issue, and as recovery is the only thing you can change whilst s-on, its a wrong recovery error.
the picture says it expects to find 366813.11 (.11 your firmware) but found something different, so failed.
alray said:
you must use the 6.09.401.11 stock recovery. Since you have re-locked the bootloader, you'll have to unlock it again, restore the stock rom again and then flash the 6.09.40.11 stock recovery so you can use ota updates. No need to relock the bootloader
okej ! so first i restore with twrp and then flash it ! do i need to root to use the nandroid for the restore ? or could i just use cmd ?
Thank u for your help !! reallyyyy !!:good:
Click to expand...
Click to collapse
Dardo27 said:
okej ! so first i restore with twrp and then flash it ! do i need to root to use the nandroid for the restore ? or could i just use cmd ?
Thank u for your help !! reallyyyy !!:good:
Click to expand...
Click to collapse
unlock the bootloader
flash twrp recovery
restore the nandroid backup linked above
flash back the stock recovery linked above
alray said:
unlock the bootloader
flash twrp recovery
restore the nandroid backup linked above
flash back the stock recovery linked above
Click to expand...
Click to collapse
do i flash the stock recovery with fastboot or just install with twrp ?
sorry for all the questions...thnx for the help
Dardo27 said:
do i flash the stock recovery with fastboot or just install with twrp ?
sorry for all the questions...thnx for the help
Click to expand...
Click to collapse
Code:
fastboot flash recovery name_of_recovery.img
fastboot erase cache
fastboot reboot-bootloader
Dardo27 said:
do i flash the stock recovery with fastboot or just install with twrp ?
sorry for all the questions...thnx for the help
Click to expand...
Click to collapse
If your using TWRP 2.8.5.0 you can flash the recovery.img right from TWRP
clsA said:
If your using TWRP 2.8.5.0 you can flash the recovery.img right from TWRP
Click to expand...
Click to collapse
interesting, how its done? I suppose we must have the recovery image on /sdcard and then we can flash it from the "install" menu?
alray said:
Code:
fastboot flash recovery name_of_recovery.img
fastboot erase cache
fastboot reboot-bootloader
Click to expand...
Click to collapse
looks like i got a red triangle now when i try to get into recovery mode
Dardo27 said:
looks like i got a red triangle now when i try to get into recovery mode
Click to expand...
Click to collapse
its normal, this is the stock recovery screen, reboot your phone in the os and check for updates.
alray said:
its normal, this is the stock recovery screen, reboot your phone in the os and check for updates.
Click to expand...
Click to collapse
should there not be like a menu for wipe and stuff ?? now its just a red triangle nothing more ?
Dardo27 said:
should there not be like a menu for wipe and stuff ?? now its just a red triangle nothing more ?
Click to expand...
Click to collapse
the menu is revealed by holding volume up and hitting power.
alray said:
the menu is revealed by holding volume up and hitting power.
Click to expand...
Click to collapse
info
What's new in 2.8.4.0:
Add flashing of boot and recovery images via the TWRP GUI (Find the Images button on the Install page)
Fix some MTP related crashes and bugs
Eliminate TWRP toggling USB IDs during boot if MTP is enabled
Fix various adb sideload issues
Improve threading of actions
Eliminate separate thread for screen timeout
Update libblkid to 2.25.0
Use power button as back button on watch themes for easier navigation
Add mutex locking to data manager
Improve custom theme handling on encrypted devices
Click to expand...
Click to collapse

[Q] HTC M7 can not get to start recovery

Hi,
I did searched the forums first to look for similar problems, but couldn't find exact problems, hence I started this thread. If by any chance I have missed it then I do apologise.
Here goes...
I have a HTC ONE M7 running 4.4.2 viper one rom, bootloader 1.54.0000 S-OFF
Problem:
I can boot the phone into bootloader menu, but I can not start the recovery. It gives an red triangle error logo stays there for a while and then reboots normally.
I have downloaded TWRP, and used fast boot command to erase cache and flashed twrp-2.6.3.3. Tried to get into recovery again, it said Entering Recovery on top of the screen and then went into a restarting loop.
what I would like to do here is to successfully flash a custom rom but for that as far as I can understand I have to enter recovery which I am failing.
In TWRP app it says recovery has been installed but I still couldn't enter the recovery mode.
Please suggest if there is any way that I can just erase the current rom and flash it with a custom rom or a NAND backup of another htc one m7 vanilla rom.
Thanks in advance hope to have a solution soon.
windyborough said:
Hi,
I did searched the forums first to look for similar problems, but couldn't find exact problems, hence I started this thread. If by any chance I have missed it then I do apologise.
Here goes...
I have a HTC ONE M7 running 4.4.2 viper one rom, bootloader 1.54.0000 S-OFF
Problem:
I can boot the phone into bootloader menu, but I can not start the recovery. It gives an red triangle error logo stays there for a while and then reboots normally.
I have downloaded TWRP, and used fast boot command to erase cache and flashed twrp-2.6.3.3. Tried to get into recovery again, it said Entering Recovery on top of the screen and then went into a restarting loop.
what I would like to do here is to successfully flash a custom rom but for that as far as I can understand I have to enter recovery which I am failing.
In TWRP app it says recovery has been installed but I still couldn't enter the recovery mode.
Please suggest if there is any way that I can just erase the current rom and flash it with a custom rom or a NAND backup of another htc one m7 vanilla rom.
Thanks in advance hope to have a solution soon.
Click to expand...
Click to collapse
Give us the output of "fastboot getvar all"
Thanks
mb_guy said:
Give us the output of "fastboot getvar all"
Thanks
Click to expand...
Click to collapse
Thanks for the reply, here is the output
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.57.0000
(bootloader) version-baseband: 2.03.30.0109
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 5.03.651.3
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno:
(bootloader) imei:
(bootloader) meid:
(bootloader) product: m7_wls
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0720000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 4106mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-1f512bb6
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.094s
windyborough said:
Thanks for the reply, here is the output
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.57.0000
(bootloader) version-baseband: 2.03.30.0109
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 5.03.651.3
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno:
(bootloader) imei:
(bootloader) meid:
(bootloader) product: m7_wls
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0720000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 4106mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-1f512bb6
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.094s
Click to expand...
Click to collapse
You have the sprint variant m7wls. You can only use roms and recovery that are specifically made for that variant.
alray said:
You have the sprint variant m7wls. You can only use roms and recovery that are specifically made for that variant.
Click to expand...
Click to collapse
Thanks for the quick reply, I am downloading this file please correct me if I am wrong.
ruu-zip-m7_wls_jb_50_sprint_1-29-651-10_ruu_decrypted-zip
Once its downloaded unzip it and then what to do? Kindly let me know.
windyborough said:
Thanks for the quick reply, I am downloading this file please correct me if I am wrong.
ruu-zip-m7_wls_jb_50_sprint_1-29-651-10_ruu_decrypted-zip
Once its downloaded unzip it and then what to do? Kindly let me know.
Click to expand...
Click to collapse
If you really want to flash RUU, you MUST NOT unzip it. You can also download TWRP for Sprint and flash it via recovery. After that choose your ROM, download it, transfer the ROM.zip to your phone using MTP option in custom recovery, and flash away
windyborough said:
Thanks for the quick reply, I am downloading this file please correct me if I am wrong.
ruu-zip-m7_wls_jb_50_sprint_1-29-651-10_ruu_decrypted-zip
Once its downloaded unzip it and then what to do? Kindly let me know.
Click to expand...
Click to collapse
well if your goal is to flash a custom recovery and then a custom rom, this file won't help. Download latest twrp for sprint variant then flash it to your phone:
Code:
fastboot flash recovery twrp-2.8.7.0-m7wls.img
fastboot erase cache
fastboot reboot-bootloader
Then boot in TWRP and flash the custom your youd like (must be a sprint rom from the sprint section)
Also remove your IMEI, MEID and SN from post #3. You want to keep these 3 numbers for yourself.
Then boot in TWRP and flash the custom your youd like (must be a sprint rom from the sprint section)
Also remove your IMEI, MEID and SN from post #3. You want to keep these 3 numbers for yourself.[/QUOTE]
Thanks a lot mate, for the answer and removing those numbers from the post. Cheers for that.
I will follow the instructions and update you with the result
O.k. I rebooted into TWRP successfully, downloaded this file from the link Guru_Reset_M7_Sprint_1.31.651.2
copied it to the root directory of the phone, flashed it, everything went well with no errors whatsoever, rebooted the phone it started fine showed me the home screen wallpaper but the screen was locked and the touch was not working, so I rebooted the phone, this time its only showing me the notification bar on top and the rest of the screen is blank, and the phone restarts on its own. Any advise please.
windyborough said:
O.k. I rebooted into TWRP successfully, downloaded this file from the link Guru_Reset_M7_Sprint_1.31.651.2
copied it to the root directory of the phone, flashed it, everything went well with no errors whatsoever, rebooted the phone it started fine showed me the home screen wallpaper but the screen was locked and the touch was not working, so I rebooted the phone, this time its only showing me the notification bar on top and the rest of the screen is blank, and the phone restarts on its own. Any advise please.
Click to expand...
Click to collapse
And why did you flashed this rom? You were telling us at post 1 that you want a custom rom/vanilla rom so why using an old stock rom? This rom is only for resetting your phone to the 1.31.651.2 software version which is not the right version for your phone (look at your getvar)
So what is your goal? You want to flash a custom rom or you want to go back to stock rom??
So what is your goal? You want to flash a custom rom or you want to go back to stock rom??[/QUOTE]
ok maybe I failed to explained myself but if you see I did said that in my very first post that its either custom rom or stock rom I just want to make it fully work.
If you can please point me to the correct rom link do not mind if its custom or stock as long as it fully works I will appreciate it. Because its a long list I got confused and made this mess, sorry about that.
windyborough said:
ok maybe I failed to explained myself but if you see I did said that in my very first post that its either custom rom or stock rom I just want to make it fully work.
If you can please point me to the correct rom link do not mind if its custom or stock as long as it fully works I will appreciate it. Because its a long list I got confused and made this mess, sorry about that.
Click to expand...
Click to collapse
ok no problem then if you want you could use the latest RUU for sprint which will update your phone to the latest stock version
http://dl3.htc.com/application/RUU_M7_WL_L50_SENSE60_SPCS_MR_Sprint_WWE_6.23.651.10.exe
Its an .exe file, launch it and follow instructions, it should take 10-15 min to flash
alray said:
ok no problem then if you want you could use the latest RUU for sprint which will update your phone to the latest stock version
Its an .exe file, launch it and follow instructions, it should take 10-15 min to flash
Click to expand...
Click to collapse
Thanks for your reply. I really appreciate your help. I will give it a go in the morning and will update you how it goes.
alray said:
ok no problem then if you want you could use the latest RUU for sprint which will update your phone to the latest stock version
Its an .exe file, launch it and follow instructions, it should take 10-15 min to flash
Click to expand...
Click to collapse
Thanks a million mate, it worked like a charm. Thank you for all your help. :good:

Categories

Resources