Hello everyone.
I have a little problem here. I just bricked my Moto X.
Bricked by Downgrade from 5.0 to 4.2 and Install a OTA. (Bad Idea).
So I read this post. I do the instructions step by step. But my Moto still "dead" no power on, no green light, no fastboot.
http://forum.xda-developers.com/moto-x/general/how-to-resurrecting-bricked-moto-x-t2629057
Please I NEED HELP!
Here are some screenshots.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
PD. My english is SO bad. Sorry about that.
That thread you linked is your last best hope.
If it doesn't work, you're likely doomed.
You could try flashing whatever version you were on previously with fastboot/mfastboot. Not 5.0, cause that doesn't exist. Whatever last official version you were on. See the complete moto X guide sticky in general for help on "returning to stock".
But what you've done is a well known guaranteed brick. Read read read.... Then do.... In the future.
Good luck!
Install RSD Lite and tell me if your device shows up in that....
TheTechDudex1999 said:
Install RSD Lite and tell me if your device shows up in that....
Click to expand...
Click to collapse
Hi, I'm in the same situation. I've flashed the bootloader too. RSD shows: "QHSUSB_DLOAD"
Computerpin said:
Hi, I'm in the same situation. I've flashed the bootloader too. RSD shows: "QHSUSB_DLOAD"
Click to expand...
Click to collapse
Sorry For the late reply... But can u connect ur phone and run adb device. Can u see ur device there. Try to manually flash all your partitions. . Ill search for some other solutions.
---------- Post added at 03:28 PM ---------- Previous post was at 03:24 PM ----------
Computerpin said:
Hi, I'm in the same situation. I've flashed the bootloader too. RSD shows: "QHSUSB_DLOAD"
Click to expand...
Click to collapse
http://forum.xda-developers.com/moto-x/general/how-to-resurrecting-bricked-moto-x-t2629057
TheTechDudex1999 said:
Sorry For the late reply... But can u connect ur phone and run adb device. Can u see ur device there. Try to manually flash all your partitions. . Ill search for some other solutions.
Hi, thanks for the answer. No, my device It's not showing in ADB.
Click to expand...
Click to collapse
Computerpin said:
TheTechDudex1999 said:
Sorry For the late reply... But can u connect ur phone and run adb device. Can u see ur device there. Try to manually flash all your partitions. . Ill search for some other solutions.
Hi, thanks for the answer. No, my device It's not showing in ADB.
Click to expand...
Click to collapse
did you try this?
http://forum.xda-developers.com/moto-x/general/how-to-resurrecting-bricked-moto-x-t2629057
also, are you on Win7 or Win8/8.1?
Try to get a Win7 if possible and run-as-admin the command prompt for ADB fastboot.
also, download the Moto X tool in the Android-dev subforum, it has some useful scripts to manually flash some stuff.
Click to expand...
Click to collapse
I tried the way of another post and I'm in Win 8.
The problem is that when the phone is flashed , the phone does not enter the fastboot mode. It shows a green LED a few seconds and the computer recognize it again as before.
Computerpin said:
I tried the way of another post and I'm in Win 8.
The problem is that when the phone is flashed , the phone does not enter the fastboot mode. It shows a green LED a few seconds and the computer recognize it again as before.
Click to expand...
Click to collapse
Green led at the top of your device means your battery is dead.
Travisdroidx2 said:
Green led at the top of your device means your battery is dead.
Click to expand...
Click to collapse
Thanks for the answer, Is there any way to make a bypass and feed the mobile directly ?
Related
Hi, I wanted to change my rom in my xperia x8, I did this many times without any problem, but this time after install MiniCM7-2.2.1 following this post
http://forum.xda-developers.com/showthread.php?t=1362585 the phone stuck in Sony Ericsson logo and the only way to turn off the phone is unplug the batery. Another curiosity thing is when I plug the phone to the pc usb port the device turned on alone.
When I try to enter to the recovery mode pressing the back button when the SE logo appears nothing happens.
I've tried with Flashtool, Sony Ericsson Update Service and many other things, but always with the same result... NOTHING.
How can I figure out if the phone is definitely a brick without solution?
Thanks!
you performed a full wipe? and are you sure that the ones you have downloaded are compatible with the kernel you're using?
Eren Jaeger said:
you performed a full wipe? and are you sure that the ones you have downloaded are compatible with the kernel you're using?
Click to expand...
Click to collapse
Hi!
Yes I did a full wipe, but now I'm not sure if I used a compatible rom with my phone, looks like I screwed up, Is there any way to fix it?
nbulian said:
Hi!
Yes I did a full wipe, but now I'm not sure if I used a compatible rom with my phone, looks like I screwed up, Is there any way to fix it?
Click to expand...
Click to collapse
Post #2
http://forum.xda-developers.com/showthread.php?t=1481630
Sent from my E16i using Tapatalk 2
Gogeta said:
Post #2
http://forum.xda-developers.com/showthread.php?t=1481630
Sent from my E16i using Tapatalk 2
Click to expand...
Click to collapse
Hi, thanks for your help, let me ask you a question, in the post "Recover your dead X8/W8" says:
If the date code on the sticker reads 11W29, or any later date (11W30, 11W31, 11W32, 11W33, ...), DO NOT attempt to unlock the boot loader.
and...
You have been warned, DO NOT TRY to unlock the boot loader on phones manufactured PAST 11W29!
Just to be sure, in my sticker phone says "11W19", could I try that solution?
This images are the last captures I made before reinstall the rom, may it helps:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
nbulian said:
Hi, thanks for your help, let me ask you a question, in the post "Recover your dead X8/W8" says:
If the date code on the sticker reads 11W29, or any later date (11W30, 11W31, 11W32, 11W33, ...), DO NOT attempt to unlock the boot loader.
and...
You have been warned, DO NOT TRY to unlock the boot loader on phones manufactured PAST 11W29!
Just to be sure, in my sticker phone says "11W19", could I try that solution?
This images are the last captures I made before reinstall the rom, may it helps:
Click to expand...
Click to collapse
you read and yet you ask? yes you can frigging unlock the bootloader.
CnC-ROCK said:
you read and yet you ask? yes you can frigging unlock the bootloader.
Click to expand...
Click to collapse
I'm sorry, english is not my language and I just want to be sure, remember... I already brick my phone trying to follow a post
nbulian said:
I'm sorry, english is not my language and I just want to be sure, remember... I already brick my phone trying to follow a post
Click to expand...
Click to collapse
bricks are common. nothing to worry about unless its hard brick. be sure the USB cable stays secure while you are unlocking the bootloader else you will end up with a dead X8
I tried to put on a custom rom on my phone but when it starts up now it says the following:
"[LGE_SECURITY ERROR] boot image signature
Critical failure: Unable to start kernel
Unrecoverable bootloader error (0x00000002)
What can I do now? got no backup
Have you unlocked your bootloader before ???
Sent from my LG-P880 using xda app-developers app
kennethlee said:
I tried to put on a custom rom on my phone but when it starts up now it says the following:
"[LGE_SECURITY ERROR] boot image signature
Critical failure: Unable to start kernel
Unrecoverable bootloader error (0x00000002)
What can I do now? got no backup
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
You couldn't be bothered to search? You didn't notice the two threads - one longer one and one created the other day - about exactly the same thing that were sat on the front page of this forum? Really?
Hint: The first Rule of XDA is;-
1. Search before posting.
Use one of our search functions before posting, whether you have a question or something new to share, it's very likely someone already asked that question or shared that news.
Click to expand...
Click to collapse
GalaxyVolvoZ said:
Have you unlocked your bootloader before ???
Sent from my LG-P880 using xda app-developers app
Click to expand...
Click to collapse
I put in "LG-Optimus-4XHD-Recovery-v1.2" and "LGUnitedMobileDriver_Ver_3.7.2_LG-P880_LGO4XHD" before using recovery to install "Carbon_1.7_root_fix".
What can i do now. I can get in recoverymode by pushin vol- and power on, but what can I do from there.? I cant transfer content to the phone so cant really get new firmware on it. maybe on the sdcard?
SimonTS said:
You couldn't be bothered to search? You didn't notice the two threads - one longer one and one created the other day - about exactly the same thing that were sat on the front page of this forum? Really?
Hint: The first Rule of XDA is;-
Click to expand...
Click to collapse
I searched! but did not find anything useful as I can not tranfer anything to the phone via usb..!
kennethlee said:
I searched! but did not find anything useful as I can not tranfer anything to the phone via usb..!
Click to expand...
Click to collapse
Three little letters ... kdz
SimonTS said:
Three little letters ... kdz
Click to expand...
Click to collapse
ive seen files with kdz yes, but my question again is how to get it on the phone now that usb isnt a solution
kennethlee said:
ive seen files with kdz yes, but my question again is how to get it on the phone now that usb isnt a solution
Click to expand...
Click to collapse
You really need to learn how to search. That's not me being arrogant, but all you need to know has been discussed many times before.
SimonTS said:
You really need to learn how to search. That's not me being arrogant, but all you need to know has been discussed many times before.
Click to expand...
Click to collapse
I have tried to follow this tutorial: http://forum.xda-developers.com/showthread.php?p=35971349
I get to the "S/W upgrade" screen. but nothing happens at all. what to do from there
kennethlee said:
I have tried to follow this tutorial: http://forum.xda-developers.com/showthread.php?p=35971349
I get to the "S/W upgrade" screen. but nothing happens at all. what to do from there
Click to expand...
Click to collapse
Find the tutorial on flashing kdz files and flash away whilst your in that screen..
PROBLEM SOLVED! The problem seemed to be that I use Win8 not Win7. Used my old laptop to flash it and it worked.
I'm stuck with a boot failure on my atrix hd. I rooted my phone with motochopper I believe. I think i made a backup of my phone. I installed TWRP. Not sure what else I did but I think that was about everything. I've got got RSD lite and the motorola drivers installed on my computer. All the boot options go to the same boot fail error. Thanks for any help. @sd_shadow
Jerdsiam said:
I'm stuck with a boot failure on my atrix hd. I rooted my phone with motochopper I believe. I think i made a backup of my phone. I installed TWRP. Not sure what else I did but I think that was about everything. I've got got RSD lite and the motorola drivers installed on my computer. All the boot options go to the same boot fail error. Thanks for any help. @sd_shadow
Click to expand...
Click to collapse
RSD Lite doesn't work well with anything higher than Windows 7.
https://forum.xda-developers.com/general/rooting-roms/guide-flashing-motorola-firmware-t4042039
Bootloader is still unlocked?
sd_shadow said:
RSD Lite doesn't work well with anything higher than Windows 7.
https://forum.xda-developers.com/general/rooting-roms/guide-flashing-motorola-firmware-t4042039
Bootloader is still unlocked?
Click to expand...
Click to collapse
Yes I believe so.
Jerdsiam said:
Yes I believe so.
Click to expand...
Click to collapse
I'm also using an old version of Windows.
Jerdsiam said:
Yes I believe so.
Click to expand...
Click to collapse
Which model number is it?
Which firmware are you using
sd_shadow said:
Which model number is it?
Which firmware are you using
Click to expand...
Click to collapse
I took a couple pictures before I broke it.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Jerdsiam said:
I took a couple pictures before I broke it. View attachment 5168031View attachment 5168033
Click to expand...
Click to collapse
Try this MB886_att-user-4.1.1-9.8.0Q-97_MB886_FFW-20-27-release-keys-ATT-US_BuildA.xml.zip
Droid-Developers SBF
web.archive.org
That one failed
Jerdsiam said:
That one failed
Click to expand...
Click to collapse
Says device is locked.
Jerdsiam said:
That one failed
Click to expand...
Click to collapse
Yes it say device locked.
Try
ATT_MB886_4.1.1-9.8.0Q-97_MB886_FFW-28_CFC_1FF.xml.zip
Redirecting...
You might need to edit the .xml file see my RSD Lite troubleshooting link
[Guide] Using Fastboot.exe with Motorola devices
Guide: Using Fastboot.exe with Motorola Devices If your device has its own section please post in that section. You can ping me with @sd_shadow MediaTek or Qualcomm Chip? Do I have a MediaTek Device? see post #26 Info: If you have a MediaTek...
forum.xda-developers.com
This is so over my head. I'm waiting on the stock site to clear. I've been reading on the editing the xml file. I'm not sure what I would need to edit. I'm gonna try to download the file again tomorrow and go from there.
Jerdsiam said:
This is so over my head. I'm waiting on the stock site to clear. I've been reading on the editing the xml file. I'm not sure what I would need to edit. I'm gonna try to download the file again tomorrow and go from there.
Click to expand...
Click to collapse
see editing .XML in this post
That File did work. Thank you so much @sd_shadow. I've been wanting to do that for 20 years. I hope I can learn what was going on in all those steps and how it all works.
Hello forum, if someone could help me finding out, whether I bricked my device doing a pat step, or if it's still possible to recover it, I'd be most glad!
After unlocking the bootloader, it might be, I did a wrong step restarting too soon or something, or trying to boot into a wrong twrp-version. Actually I don't remember each step, as this happened a few months ago...
Thank you for now,
draftflash
if you still can, boot into fastboot and on your pc type
fastboot -w reboot.
if it doesn't work then consider using this firmware updater https://forum.xda-developers.com/t/rom-stock-rom-for-xt2083-reteu.4214883/
NoEscapeCh said:
if you still can, boot into fastboot and on your pc type
fastboot -w reboot.
...
Click to expand...
Click to collapse
worked! Wow! Life can be so easy Thank you!
But how come, I cannot boot into the proper twrp?
-> https://forum.xda-developers.com/t/...0-guamp-moto-g9-g9-play.4189901/post-83917303
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
draftflash said:
worked! Wow! Life can be so easy Thank you!
But how come, I cannot boot into the proper twrp?
-> https://forum.xda-developers.com/t/...0-guamp-moto-g9-g9-play.4189901/post-83917303
Click to expand...
Click to collapse
Try download stock rom then open find recovery.img and fastboot flash...woork for my bootloop
also twrp.img not work touch screen im bypass this by using PC mouse put USB rerciever in phone trough usb-c to USB from samsung box from mobile
draftflash said:
Hello forum, if someone could help me finding out, whether I bricked my device doing a pat step, or if it's still possible to recover it, I'd be most glad!
After unlocking the bootloader, it might be, I did a wrong step restarting too soon or something, or trying to boot into a wrong twrp-version. Actually I don't remember each step, as this happened a few months ago...
Thank you for now,
draftflash
Click to expand...
Click to collapse
Hi, were did you got that version of TWRP?
rogue.bot said:
Hi, were did you got that version of TWRP?
Click to expand...
Click to collapse
Hi rogue.bot, don't remember, maybe an instruction to install /e/ for Moto G7. Anyway, new state is that I recovered the STOCK and now 'd like to install the proper twrp, which should be available now, as I saw.
will the files on this thread be fine?
https://forum.xda-developers.com/t/recovery-unofficial-twrp-3-4-0-0-guamp-moto-g9-g9-play.4189901/
draftflash said:
Hi rogue.bot, don't remember, maybe an instruction to install /e/ for Moto G7. Anyway, new state is that I recovered the STOCK and now 'd like to install the proper twrp, which should be available now, as I saw.
will the files on this thread be fine?
https://forum.xda-developers.com/t/recovery-unofficial-twrp-3-4-0-0-guamp-moto-g9-g9-play.4189901/
Click to expand...
Click to collapse
Thanks, sorry for my late replay. I thought that /e/ was only for pixel phones, is it any better (in privacy) than LinageOS?
rogue.bot said:
Thanks, sorry for my late replay. I thought that /e/ was only for pixel phones, is it any better (in privacy) than LinageOS?
Click to expand...
Click to collapse
ouh, don't think so. I choose it for being said to be a bit lighter. But I am thinking of changing back to LineageOS for /e/ is a bit too close to conventional ROMs, regarding the user surface. But actually I don't know the newer versions of LineageOS.
draftflash said:
ouh, don't think so. I choose it for being said to be a bit lighter. But I am thinking of changing back to LineageOS for /e/ is a bit too close to conventional ROMs, regarding the user surface. But actually I don't know the newer versions of LineageOS.
Click to expand...
Click to collapse
I dont know if it is available, but for another phone I´ve tried dotOS and was pretty nice, at least on the surface, didn´t dig too deep inside the OS but it seems like a good option, also it has optimization in its DNA
is there a tutorial to root your device on here
Hello everyone!
First of all I want to apologize if this question been resolved( I didn't find).
My problem is that I have tencent edition 256/12 with WW firmware version 17.0823.2007.32 and it can't be updated. I know that in my situation it should be possible when downloading update from off web page and manually installing it. But it don't work(
I find video how to change firmware from CN to WW, but none of my PCs don't want see phone properly (in device manager it appear with exclamation mark).
Then I find information about unlocking boot loader, app been installed, couldn't unlock.
Then I read about EOM unlocking in developer settings, and there is no such menu.
After all this I hoping that someone can help me.
Best regards!
Grab a mint-lemon tea, relax, watch this video attentively and follow the instructions to the T
elmor0 said:
Grab a mint-lemon tea, relax, watch this video attentively and follow the instructions to the T
Click to expand...
Click to collapse
That's the point I try like in this video, and could not even unlock device
NoobSnail said:
That's the point I try like in this video, and could not even unlock device
Click to expand...
Click to collapse
What was the error or issue you faced and couldn't unlock the bootloader?
Any logs?
Images?
animegamer4422 said:
What was the error or issue you faced and couldn't unlock the bootloader?
Any logs?
Images?
Click to expand...
Click to collapse
Unfortunately when I press unlock device only restarts and that's all, I saw info that it's ok and need to do this procedure 4times but it didn't help me. So I have no errors, even when I try to install update manually it only says "error try again"
There's no OEM unlock for this device under Developer options.
Ensure USB debugging is enabled.
Make sure you install correct drivers installed on your PC.
Use official Asus bootloader unlock tool.
elmor0 said:
There's no OEM unlock for this device under Developer options.
Ensure USB debugging is enabled.
Make sure you install correct drivers installed on your PC.
Use official Asus bootloader unlock tool.
Click to expand...
Click to collapse
Just installed all drivers on another PC, still got same exclamation mark.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Other devices-> android.
NoobSnail said:
Just installed all drivers on another PC, still got same exclamation mark.
View attachment 5618275
Other devices-> android.
Click to expand...
Click to collapse
Try using the Origin sdi tool to download those drivers , search on YouTube for a tutorial on Chris Titus Tech channel (sorry can't post any links)
Agree, sounds like a driver issue as device not being recognised, assuming you have followed all the other steps correctly.
animegamer4422 said:
Try using the Origin sdi tool to download those drivers , search on YouTube for a tutorial on Chris Titus Tech channel (sorry can't post any links)
Click to expand...
Click to collapse
Thank you very much now my phone is visible correctly in device manager.
elmor0 said:
Agree, sounds like a driver issue as device not being recognised, assuming you have followed all the other steps correctly.
Click to expand...
Click to collapse
Thank you for help and time that you spend.
If maybe someone know if I have bad firmware I need to do all steps like in Bobby Prats video guide? Simply try to install firmware that he recommend? I mean for my phone now it will be WW 2007.32 to WW 2007.32
Factory reset
sony.electronic said:
Factory reset
Click to expand...
Click to collapse
After factory all steps from video, correct?
NoobSnail said:
Hello everyone!
First of all I want to apologize if this question been resolved( I didn't find).
My problem is that I have tencent edition 256/12 with WW firmware version 17.0823.2007.32 and it can't be updated. I know that in my situation it should be possible when downloading update from off web page and manually installing it. But it don't work(
I find video how to change firmware from CN to WW, but none of my PCs don't want see phone properly (in device manager it appear with exclamation mark).
Then I find information about unlocking boot loader, app been installed, couldn't unlock.
Then I read about EOM unlocking in developer settings, and there is no such menu.
After all this I hoping that someone can help me.
Best regards!
Click to expand...
Click to collapse
Try with Factory Firmware or change the product
sony.electronic said:
Try with Factory Firmware or change the product
Click to expand...
Click to collapse
Ow I see ok thank you
You can flash RAW of CN or WW firmware.