Hi ,
since the last updates the lock screen is cut off either at the left or right side.
I don't think that's by design
ominrom 4.4.4-20150127-i9300-nightly
Cheers wgk
Related
Recently I added a screen protector to my Alpine, and after that the screen started acting funny any time it was left alone. Removing the screen protector has made no difference.
After a short while of not being used, the screen becomes misaligned, for example if I leave it off for an hour, attempting to activate the start menu on the today screen will result in one of the today items being pushed, or attempting to select a number on the password entry will result in a different number being pressed.
The strange thing is I can re-align the screen through the control panel, but it will slowly go back to the way it was.
Anyone got any thoughts? At worst, I'll just refund it (I bought it where I work, and thats no problem) and get another handset, but if theres a fix I'd prefer to stick with my current handset.
Cheers in advance for any help!
I am not sure about this, but I had the same problem with Motorola A1000 touch screen - could it be that an excessive pressure was applied to one of the sides of the digitizer during the application of screen protector? The digitizer is glued on the LCD, there might be a remote chance that it has slid a little to one side. Also some extra glue could have shortened the contacts on the bottom part of the digitizer. I would try to clean it first with some anti-static liquid. Hope this helps..
Indeed, this sounds like there could be more pressure to one side of the screen than the other, hence the digitiser tries to adjust for the pressure difference and gradually falls out of sync.
Try reapplying your screen protector, more gently than last time if possible, but don't wipe from side to side, wipe from top to bottom with an even pressure. Also, try realigning the screen with the protector off before reapplying it.
I had a problem with my screen originally before I got my screen protector, insofar as I got that 'rainbow' pooling effect in the centre of the screen where the digitiser was touching the LCD layer - after about a week after application of the screen protector, however, the more even layer of tension provided by the protector somehow pulled the digitiser away from the LCD layer, so my screen has actually gotten better since then... That said, I could imagine that uneven tension on the top layer could lift the LCD and digitiser layers further away from each other on one side than on the other, causing the problem you describe here. If you can bear to, try using the phone for a couple of days without the protective top layer applied, and see if the alignment gradually slips out as it's doing at the moment.
I've been using the phone for the past two days without the protective cover on. I'm going to reapply it now and then see how it goes tomorrow. If its still screwed, I'll reflash it to the O2 ROM and refund it at work on Tuesday.
Got a replacement, so no problem now. Thanks for the help anyhow
My screen constantly goes out of alignment.
I have to realign it 10-12 times a day and sometime it goes out by alot !
I have tried 6 different ROMS and they all have the same problems
Can anyone help ?
Thanks
yeh.. mine's like that too... except it only seems to happen when it gets a bit warm.... haven't been able to find a solution for it so far.
Did a few searches and the general consensus seems to be that it's a hardware fault (screen and digitiser) and other people have sent it off for warranty repairs.
I'm going to have problems with the warranty as I have changed the Rom many many times.
Don't know how to put the original Telstra ROM back, assuming I can even get it !
Hey guys
I am on my 2nd diamond..
the first one had huge alignment problems, so i got it replaced..
after a month, the new one started doing the same thing..
i found a thread somewhere here on XDA (for the life of me cant remember where it is now)
but it had a little solution that mixed with mine, worked!
the problem is that the screen is not sitting properly in the casing anymore, possible due to a bump in your pocket, or a fall.. this causes a certain section of the screen to be higher or lower than the rest..
place the phone flat on a desk, and open up the notes app and try to write/draw something.. see which side of the screen the line is heading towards..
now place place your thumb and a finger on diagonal sides of the screen (eg, bottom left and top right) and press down... check with the stylus if its any better... if not, try opposite sides and check again..
mine always shot up to the top right, so when i held down the top left side of the phone, it worked..
so this meant that the top right side was sitting slightly higher than the rest of the screen.
the solution is:
find a business card with sharp corners and place the edge underneath the screen (just the corner, dont shove the whole thing up there!) hehe
then slide the card up and down a few times, and then do another side of the screen... do all 4 sides but pay special attention to area where the styles was migrating towards in the notes app..
after doing this, my phone hasnt given me a days problem in 2 months now..
give feedback if this solution works for you!
my touch 3g became unresponsive at right lower corner of the screen. within a day, whole of screen became unresponsive
I have the same problem but fot the left part of the screen. Any ideas?
Yuppers. The digitizer's borked. Have it replaced, it costs some 12 Euro on eBay.
I had the same problem with my Jade.With a simple action it came back to life.I took a sharp knife and raised a bit the plastic upper cover on the Digitizer.It worked instantly.Perhaps a small quantity of air or humidity has entered between the Digitizer and the upper plastic cover.This was the problem of my Jade.When i looked on the screen with the light off i could see some shapes on it.If you can see them too,perhaps you're having the same problem.
any tutorial?
Does anyone else have this problem:
When you're just pressing a bit harder than the usual touch, on the top and bottom Left side bezel, it causes the Screen to ripple (fluid wave effect).
Not even pushing down too hard, just a firmer press than usual. This is easy too see on a darker background, like the default background when the device wakes up and still in locked mode.
Yes I realize it's a LCD screen, plus this Corning glass is thinner, and we're not always pressing it that hard to notice anyway.
But the Right side bezel and other areas are mostly fine,
So I'm wondering if it's a defect on my device or not (the left side being too sensitive)? would this cause further problem in the future? And it could be a concern if I carry the Nexus 7 in the backpack and other items pressing on it.
Other reports on this:
http://www.theverge.com/2012/6/29/3125396/google-nexus-7-review
"the display can give a little and cause the LCD to ripple if you really press hard against the screen"
http://forums.androidcentral.com/google-nexus-7-tablet-forum/191040-screen-distortion.html
I wonder if I try the Fix on the other thread, taking off the cover, but instead, loosen the screws a bit on the left side, would that help?
Thanks!
Hi,
My device has this too. Mostly on the left side & a little less on the right side but hardly any on the top or bottom.
Hi everybody
I think that the fingerprint sensor should be placed in the middle of the screen.
Many of the renders we have around the web, show it at the bottom of the screen though.
With a screen as large as this, I think this would be even worse than having it on the back of the phone.
Now that they can put it in the screen itself, the most convenient and user productive place for it is somewhere in the middle of the screen.
So if anybody knows where is it situated, please share this.
I cradle the bottom of the phone with my pinky. That would position my thumb 1/3 from the bottom of the screen. Putting it in the middle would strain my hand a little.
garyHal said:
I cradle the bottom of the phone with my pinky. That would position my thumb 1/3 from the bottom of the screen. Putting it in the middle would strain my hand a little.
Click to expand...
Click to collapse
Didn't get that... I'm only saying that when I'm holding a phone with similar size, the thumb is around the middle of the screen or a bit lower than that.
it is the bottom middle
SuperLeakTX said:
it is the bottom middle
Click to expand...
Click to collapse
Thanks
Though I'm still hoping this is not the case...