Well, I fixed my old broken G1 with new screen, touchscreen panel, case and keyboard.
Now I have 2 issue:
1) Sometimes my touchscreen goes grazy!! If I use the touch test application I see that sometimes when I touch the screen in an area there is another virtual touch in another zone of the screen. I read that it can depend from the current source when I charge the phone.. but I'm going crazy!! I opened my phone 10 times (I thought there was a problem in the cable that link TouchPanel to LCDPanel, because when I lock the cable with the clip it tends anyway to go out from the connector, now I put some scotch tape to fix but the problem is here.. so I think is another problem).
2) My volume rocker doesn't work!!
I bought 2 new keyboard to fix this problem, but no one of that fixed the problem. I thought the first new keyboard had volume keys broken, so I bought another one, but the problem persists!!
Now the Touch problem rarely happens, but the volume rocker is completely unusable..
Someone have experience about G1 assembling/repairing ?
Thanks and sorry for bad english
if you have put in multiple keypads have the same issue i would assume that it is the connection going to the motherboard. just a guess there but its either that or you have had a bunch of faulty keyboards.
only other thing would be a software problem
does the keypad work in recovery (let you go up down throughout the list) ?
as for the touch screen, probably need a new digitizer or flex cable, both are cheap and it sounds like you have the knowhow to replace them.
Ok, but digitizer is new!! screen also is new, and I have bought a total of 4 flex cable because I see that they are fragile (I broke the first I bought).
I tried to change flex cable but the problem remain the same.
The only thing that can be damaged is the LCD cable that links to the flex cable: it has a small cut where the cable have a curve, but the cut don't reaches the contacts (the cable is transparent). I also use some glue and scotch tape to mantein lock the cable.
The digitizer cable is connected to the LCD cable, and then they go to the flex cable that connect them to the motherboard.
The strange thing is that seems a software issue, because if I turn off and than turn on the screen, the problem is fixed for some seconds, minutes and sometimes hours...
Another strange thing is the possibility to control the screen with some metal objects from the moment that the virtual touch problem appear (I can control the screen also without touch it, with hand and piece of metal)
video:
have you tried a factory reset if you think it may be a software issue? if that dosent work you can try install a whole new rom.
really it sounds like it isnt the hardware since you appear to know what youre doing. i have a had a few phones that had screen (digitizer) issues and a new rom flashed cured it just fine
since you dont mind putting a few dollars into it, and your familiar with the inside, you can always try to pick up a cheap motherboard or spare phone from ebay or what have you, then swap the motherboard and you could then hopefully find out if it is the hardware or software
nagash91 said:
Another strange thing is the possibility to control the screen with some metal objects from the moment that the virtual touch problem appear (I can control the screen also without touch it, with hand and piece of metal)
Click to expand...
Click to collapse
Huh sounds like you got a cheap digitizer than. Most good digitizers use heat to touch. If it's literally touch, then sounds like its a fake/meh digitizer. i hate the digitizers that aren't heat, but press. I see them all the time in those first samsuck touchscreen phones. And they usually die in a bit. I had a Samsung behold with a screwed up digitizer
demkantor said:
have you tried a factory reset if you think it may be a software issue? if that dosent work you can try install a whole new rom.
Click to expand...
Click to collapse
Yes I flashed 3 or 4 roms after a wipe (I tried also super-wipe.zip), but the problem is here..
The digitizer works well some times, but sometimes get crazy (you can see in the video).
I don't that my new digitizer is fake, but I really don't know!
BTW I'm trying to repair my phone for fun (now I have desire z) and because I am fascinated by my old G1.
PS:
I see another strange issue--
If I touch the screen when the phone is on a table the screen digitizer is not very sensitive and can't take input from fingertips.
If I touch the screen when the phone is in my other hand, the screen digitizer is a lot more sensitive and it take input from fingertips.
My impression is that there is an electric field or something similar that disturbs the digitizer, and when I take the phone in my hand I discharge that field to ground. Also when I turn off the screen, seems that the electric field discharge so when I turn on the screen is ok, but after some seconds the field returns to disturbs the screen.
I really don't know, but is the impression that I have.. something that is not shielded.
Now I'll try to use my phone in airplain mode.
Thanks guys, I'm happy to see that this forum is still very active
Hello everyone,
I have got one problem... I broke digitizer of my HTC Desire 500. So I order new one and to be sure, also LCD screen. I replaced, and...
After turning on, everything works fine. Digitizer works properly, screen shows normal picture. But after few minutes - restarts (I don't remember well) backlight of my screen goes down and now it have no backlight at all. I rebooted phone many times, I remounted screen and digitizer to be sure that connections are fine - but no results. I restored factory settings of phone with no effect too. :/
Please help, what happend? What could be the source of problem? I don't want to order new sceen if it could beak too ;/ I read other threats about coil problem in other HTC, but I cannot find any coil in my Desire's motherboard (maybe it is hidden under plate that covers CPU and other parts). I performed tests of light sensor and it works fine. Buttons lights fine too. The problem refers only to LCD screen, and backlight doesn't respond during test.
Anyone help?
same situation
Hello kowal_luki,
I'm just in the same bad situation.
After a bad fall of the phone the screen broke so I ordered a new one for replacing it.
Opening the phone I noticed that also the LCD (and not only the external screen) was broke so had to order also the LCD.
As precaution tried to power-on my device without a complete assembly and everything seemed to be fine, so I decided to glue the LCD to the outer screen (the touch screen) with a LOCA TP-2500 glue.
Then I re-assembled it up: at first the image was a little bit disturbed but the back-light was working; after few second the back-light turned off. I checked the cable, after that the image went perfect but the back-light still dead.
Did you find a solution for this -still not explanable- problem?
I Cracked my screen to the point the bottom half no longer worked. I got a replacement and installed it. My LED light comes on and I can feel the vibration when 'unlocking' but my screen is black/blank. Does this mean I have a faulty LCD screen or do I need to do some type of hard reset?
Good Day to All,
I have a problem with my Z3+ E6553, the problem is that there is no display on the phone. Couple of weeks ago the lcd just stopped working, the device does come on with the LED lights, vibration and the touch is reponsive with which you can here the touch sounds, haptic feedback and the Speech to text speaking. I thought the LCD screen went dead and so I bought a new LCD screen to replace it but after replacing the screen the problem still presist with no display(black screen). So currently I have no idea what is the cause or what to do next.
I opended the phone was just check some things out, and I had a look at the LCD flex cable and I found something strange that maybe one of the connector antenna prongs missing. But I'm not sure if thats just how it is or its maybe it got damaged. Have a look at the attached pictures below.
Can someone tell me if this issue is with the LCD motherboard flex cable, or another hardware issue maybe being the motherbaord?
Hi, my screen broke recently and i can't use the tactil touch. I can see the image but can't use. So i decided to buy a LCD + Tactil Touch + Frame. I didn't mount yet the screen. I only disconneted the screen flex and connected the flex of the new screen. But the problem is that is black. The screen seems to turn on but i don't see anything, is all black.
EDIT: I don't know where to ask. I flashed to the stock ROM, 4.2.2 and still black. I updated to the last version Sony has for my phone, 5.1.1 and still is black. I don't know what more to do. Is all working good, even the sounds when i touch the screen. But i can't see anything the screen is working but there's no image. My phone is Xperia Z.
Anyone?
Please help!
Broken screen? Is the old one still working? If yes: return the new and broken display and get a replacement!
The touch("screen") and feedback (vibrate and sound) will work without the lcd! It is a different layer on the screen and is seperatly connected to the mainboard of the cellphone. Also your screen could be working and your backlight not! Turn on the phone and point a bright flashlight on the screen, maybe you will see something, but even then, get a replacement.