[How-To] Unbrick or Flash Back to Stock(NCE) - G900A Only - AT&T Samsung Galaxy S 5

***The steps below will work on all Bootloader versions except OC4(Android 5.0), Do not use this process if you have taken the OC4 ota update!***
1. Download the G900A_Downgrade_to_NCE.rar and extract the .tar.
2. Go into Download Mode by pressing and holding the Home, Volume Down, and Power keys on your device until the phone powers on and displays warning screen, then press Volume Up key.
3. Flash the G900A_Downgrade_to_NCE.tar using Odin's PDA slot(AP in Odin v3.09+).
Note: The most common cause of an Odin flash failure is a bad usb port or cable. Please check before reporting a failure!
Attention! If you have taken the OC4 ota update and need to unbrick after attempting to downgrade try flashing the: G900A_OC4_Stock_Partitions

So why is it that the g900a is the only gs5 that can't downgrade from 5.0? even Verizon can???

I had a different Downgrade to NCE file. Tried this one and my phone is back up and running. Phew!! Thanks so much!!

Is it safe to flash over ND3? I'm not recieving any ota. Will I receive Ota After flashing this?

DIME8611 said:
Is it safe to flash over ND3? I'm not recieving any ota. Will I receive Ota After flashing this?
Click to expand...
Click to collapse
Yes. You can OTA all the way to OC4.
Sent from my SAMSUNG-SM-G900A

Added G900A_OC4_Stock_Partitions to the OP for those that took the OC4 ota update and bricked while attempting to downgrade.

muniz_ri said:
Added G900A_OC4_Stock_Partitions to the OP for those that took the OC4 ota update and bricked while attempting to downgrade.
Click to expand...
Click to collapse
Muniz do u think there will be root method for those on 5.0 ota unrooted? ???

Phone gets stuck up!
For some reason. i tried to unbrick my phone from the rooted stock firmware 5.0 and it ended up with the boot loop. Already tried the downgrade to NCE. Now it gets worse because all I can see so far is the logo of ATT and that's it. Anyone could help me out with that???

NVQT said:
For some reason. i tried to unbrick my phone from the rooted stock firmware 5.0 and it ended up with the boot loop. Already tried the downgrade to NCE. Now it gets worse because all I can see so far is the logo of ATT and that's it. Anyone could help me out with that???
Click to expand...
Click to collapse
I'm sure you probably already tried this but if not pull the battery for a few seconds and then try going back into download mode and try the process again.
How did you upgrade to 5.0 (which method) You may have to provide more detail, there are a lot people who have way more knowledge than I do, but I hope this helps
Good luck and give the forums a search

unk2009 said:
I'm sure you probably already tried this but if not pull the battery for a few seconds and then try going back into download mode and try the process again.
How did you upgrade to 5.0 (which method) You may have to provide more detail, there are a lot people who have way more knowledge than I do, but I hope this helps
Good luck and give the forums a search
Click to expand...
Click to collapse
Thanks for the reply! I actually upgraded to 5.0 by the flashfire method since before that I already got the rooted 4.4.4. Just yesterday, when I left my phone for a while and came back, it started to stick with the bootloop, , the only method which could help it out is to plug it into the power source. I tried everything which includes removing battery and wiping factory downgrading, flashing original firmware, reinstalling the OTA 5.0 update through sdcard. None of that worked. If you have any information to help me out,I would be way happy to listen! Thank you !

I've had this same problem. Are you still bootlooping?
Sent from my SAMSUNG-SM-G900A

THANK YOU...
I'm with archie above - I tried a different downgrade file and it didn't work either - this one DID.
Thanks so much...

Thank you so much for this. Worked perfectly for a downgrade from 4.4.4. You're the best!
Currently installing updates OTA.

Hi muniz, I posted in your KeepRoot for 5.0 thread and then I saw this one. My phone seems to have spontaneously softbricked (system crashes and then it bootloops). Will flashing the stock 5.0 make me lose root?
EDIT: Fixed with a battery pull!

muniz_ri said:
Attention! If you have taken the OC4 ota update and need to unbrick after attempting to downgrade try flashing the: G900A_OC4_Stock_Partitions
Click to expand...
Click to collapse
Just to clarify, my S5 is on the OC4 build. Will I be able to downgrade to KK using the above file, or is it ONLY to fix a device that got bricked while trying to downgrade? If the latter, are OC4 users just hosed? I have scoured this site, but would appreciate links to any instructive threads that I may have missed. Thanks!

muniz_ri said:
***The steps below will work on all Bootloader versions except OC4(Android 5.0), Do not use this process if you have taken the OC4 ota update!***
1. Download the G900A_Downgrade_to_NCE.rar and extract the .tar.
2. Go into Download Mode by pressing and holding the Home, Volume Down, and Power keys on your device until the phone powers on and displays warning screen, then press Volume Up key.
3. Flash the G900A_Downgrade_to_NCE.tar using Odin's PDA slot(AP in Odin v3.09+).
Note: The most common cause of an Odin flash failure is a bad usb port or cable. Please check before reporting a failure!
Attention! If you have taken the OC4 ota update and need to unbrick after attempting to downgrade try flashing the: G900A_OC4_Stock_Partitions
Click to expand...
Click to collapse
HI, i flash using this method, everything pass and after rebooting, it got stock on a black screen and the LED light is blue, and i can´t use my pone and i don´t know how to , please help.
---------- Post added at 04:01 PM ---------- Previous post was at 03:56 PM ----------
javierascua said:
HI, i flash using this method, everything pass and after rebooting, it got stock on a black screen and the LED light is blue, and i can´t use my pone and i don´t know how to , please help.
Click to expand...
Click to collapse
and another thing before doing this downgrade i was on 5.0 but using flashfire

Vol4Ever said:
Just to clarify, my S5 is on the OC4 build. Will I be able to downgrade to KK using the above file, or is it ONLY to fix a device that got bricked while trying to downgrade? If the latter, are OC4 users just hosed? I have scoured this site, but would appreciate links to any instructive threads that I may have missed. Thanks!
Click to expand...
Click to collapse
Yes, those that took the OC4 ota are out of luck.

Muniz_ri, thxs very much i use your flash downgrade and solve my problem

Omg i love you!!!!!
It totally work for me, i downgrated from briked lolipop, and safe my phone!!!!!

help please
alright so i accidently flashed the gs5 active kernel onto my g900A and its completely bricked, like i cant even get into download or safemode from power off. please tell me therres a possible solution?!?

Related

Need Help ASAP

I was trying to use this method for safestrap the how to root the new 4.4.4 update i amd still on 4.2.2 but i installed the rom and i flashed the wrong kernel now my phone is boot looping and wont go anywhere. What can i do.
[How-To] Root G900AUCU2AOA1 4.4.4 (2/3/2015) that is the method i used. I was one i believe on NG3 and is there a way to odin back to stock rom because i can put it in download mode.
willyyumm27 said:
I was trying to use this method for safestrap the how to root the new 4.4.4 update i amd still on 4.2.2 but i installed the rom and i flashed the wrong kernel now my phone is boot looping and wont go anywhere. What can i do.
[How-To] Root G900AUCU2AOA1 4.4.4 (2/3/2015) that is the method i used. I was one i believe on NG3 and is there a way to odin back to stock rom because i can put it in download mode.
Click to expand...
Click to collapse
Odin back to stock NCE then repeat the process to update and root using @muniz_ri thread its super easy actually.
Don't worry you're not bricked.
http://forum.xda-developers.com/showthread.php?t=3021120
Thank you so much! I also had another question can you downgrade back to nce if you are on 4.4.4? Using the same method as before ?
willyyumm27 said:
Thank you so much! I also had another question can you downgrade back to nce if you are on 4.4.4? Using the same method as before ?
Click to expand...
Click to collapse
Yep I just did last night messing around
Thank you for the help!
I did this same thing. But when I tried to flash back to stock it stays bootlooping.
Ndvorak said:
I did this same thing. But when I tried to flash back to stock it stays bootlooping.
Click to expand...
Click to collapse
What exactly did you do please provide more information
OPOfreak said:
What exactly did you do please provide more information
Click to expand...
Click to collapse
I did this.
http://http://forum.xda-developers.com/att-galaxy-s5/help/messed-t3023635
Ndvorak said:
I did this.
http://http://forum.xda-developers.com/att-galaxy-s5/help/messed-t3023635
Click to expand...
Click to collapse
Very easy go back and reread the OP and follow each step exactly you've obviously missed a step.
Take your time its easy to miss something if your frustrated.
As long as you get into download you'll be fine and can get it fixed.

[Q] Help. Device [SM-G900A] stuck in Black-and-Blue bootloop and soft brick.

This is common for failure when modifying firmware with Odin. Black-and-Blue is what I call the error. My screen has gone black after a failure after the color Samsung animation, and the blue boot light is looping. I tried following instructions on how to un-brick it. They are all the same though. Odin, firmware. But what had caused the problem was this exactly. I need a way to fix this. Unless it is just easier to bring it in for maintenance. (I have not tripped Knox as I was only installing Firmware.) I cannot connect to Kies. I can access Stock Recovery and download mode. Can anyone suggest anything different than this method?
I am a new user at XDA but I am not new to Android or the Forums. I know many things, so you don't have to be too lament.
ALL HELP IS GREATLY APPRECIATED, AS I MUST HAVE THIS SOLUTION BY 2 DAYS
ElectricBiskitz said:
This is common for failure when modifying firmware with Odin. Black-and-Blue is what I call the error. My screen has gone black after a failure after the color Samsung animation, and the blue boot light is looping. I tried following instructions on how to un-brick it. They are all the same though. Odin, firmware. But what had caused the problem was this exactly. I need a way to fix this. Unless it is just easier to bring it in for maintenance. (I have not tripped Knox as I was only installing Firmware.) I cannot connect to Kies. I can access Stock Recovery and download mode. Can anyone suggest anything different than this method?
I am a new user at XDA but I am not new to Android or the Forums. I know many things, so you don't have to be too lament.
ALL HELP IS GREATLY APPRECIATED, AS I MUST HAVE THIS SOLUTION BY 2 DAYS
Click to expand...
Click to collapse
Head down to this thread http://forum.xda-developers.com/att...to-root-g900aucu2aoa1-4-4-4-2-3-2015-t3021120 and scroll down to the notes section and download the G900A_Downgrade_to_NCE.tar. Boot into download mode and flash using the pda slot in ODIN. Take both OTA's and youll be back on latest stock firmware.
Thanks
Thanks for responding. I have gotten it fixed. I installed an older kernel.
ElectricBiskitz said:
Thanks for responding. I have gotten it fixed. I installed an older kernel.
Click to expand...
Click to collapse
I've got the same problem. Do you mind sharing some details on how you got the older kernel?
Yes
ElectricBiskitz said:
Thanks for responding. I have gotten it fixed. I installed an older kernel.
Click to expand...
Click to collapse
Go to this linked site -> http://forum.xda-developers.com/att...to-root-g900aucu2aoa1-4-4-4-2-3-2015-t3021120
Here you'll find how to root. Go to the troubleshooting section and download a tar called G900A_Downgrade_to_NCE.tar to your computer. Then inject to AP in Odin.
Hope this will work! ?

[Q] Unable to download any new software updates

Whenever I used to try to update my phone from 4.4.2 to 4.4.4, my phone would say the installation was interrupted, and kies would say my firmware is up to date. At the time I didnt care much, but now that 5.0 is out, I want to figure this out. When I got my phone in September I flashed the original software to root, then reflashed 4.4.2. Since then I unrooted and restores my phone to try and resolve the problem, but neither have helped. Does anyone know a solution? If any more information is needed I can definitely provide it.
SyslogPlease said:
Whenever I used to try to update my phone from 4.4.2 to 4.4.4, my phone would say the installation was interrupted, and kies would say my firmware is up to date. At the time I didnt care much, but now that 5.0 is out, I want to figure this out. When I got my phone in September I flashed the original software to root, then reflashed 4.4.2. Since then I unrooted and restores my phone to try and resolve the problem, but neither have helped. Does anyone know a solution? If any more information is needed I can definitely provide it.
Click to expand...
Click to collapse
I have the same problem on my side. I haven't even ever rooted the phone. Always the same error. I have posted this issue here, lets see if some one replies.
http://forum.xda-developers.com/att...ipop-coming-soon-t3030721/page18#post59986756
SyslogPlease said:
Whenever I used to try to update my phone from 4.4.2 to 4.4.4, my phone would say the installation was interrupted, and kies would say my firmware is up to date. At the time I didnt care much, but now that 5.0 is out, I want to figure this out. When I got my phone in September I flashed the original software to root, then reflashed 4.4.2. Since then I unrooted and restores my phone to try and resolve the problem, but neither have helped. Does anyone know a solution? If any more information is needed I can definitely provide it.
Click to expand...
Click to collapse
I had the same issue I used the files from this thread http://forum.xda-developers.com/att-galaxy-s5/general/how-to-root-g900aucu2aoa1-4-4-4-2-3-2015-t3021120 under troubleshooting I first downloaded and then flashed the file to downgrade to nce. Then downloaded the nce to ng3 ota file and sideloaded and flashed in stock recovery after that I have been able to download and update via the ota. hope this helps
doing that process
I can manage the first flash but I'm not really that good at this so how would I go about doing that second flash?
SyslogPlease said:
I can manage the first flash but I'm not really that good at this so how would I go about doing that second flash?
Click to expand...
Click to collapse
You need to place the update file on your ext sdcard then boot into stock recovery and update from ext sdcard.
wildcard30 said:
I had the same issue I used the files from this thread http://forum.xda-developers.com/att-galaxy-s5/general/how-to-root-g900aucu2aoa1-4-4-4-2-3-2015-t3021120 under troubleshooting I first downloaded and then flashed the file to downgrade to nce. Then downloaded the nce to ng3 ota file and sideloaded and flashed in stock recovery after that I have been able to download and update via the ota. hope this helps
Click to expand...
Click to collapse
Last questions are how to go into stock recovery and once I do that its all normal again?
How to boot Samsung Galaxy S5 Recovery Mode:
Power off your device completely.
Boot recovery mode by pressing and holding Volume Up, Home and Power, all at the same time.
Release all buttons when the Galaxy S5 screen flickers and the main Recovery screen will appear.
Once I updated to ng3 through the stock recovery I was able to take the ota updates for 4.4.4 and 5.0 normally.
Thanks, I'm going to try this now. Hope I don't lose any data!
SyslogPlease said:
Thanks, I'm going to try this now. Hope I don't lose any data!
Click to expand...
Click to collapse
you will when you flash through stock recovery.
Back up your data
It all went smoothly and I can update again! Thanks so much!
You are welcome.
I tried the instructions in that thread but I get an error when I try to install the first update.
The error mentions unexpected contents
What I did is copy the file to the SD card, booted into recovery and then selected install from external
What did I do wrong?
Hi there. Thank you so much for this. Question is that I am already on NG3 and I still dont have the update option! Would I need to go to OA1 one? Which I believe is 4.4.4? Then get the update for lollipop? A little confusion. And if that is the case, where can I get the file thing for OA1?
juliusgy said:
I tried the instructions in that thread but I get an error when I try to install the first update.
The error mentions unexpected contents
What I did is copy the file to the SD card, booted into recovery and then selected install from external
What did I do wrong?
Click to expand...
Click to collapse
I have the same problem, except I used adb sidoload
juliusgy said:
I tried the instructions in that thread but I get an error when I try to install the first update.
The error mentions unexpected contents
What I did is copy the file to the SD card, booted into recovery and then selected install from external
What did I do wrong?
Click to expand...
Click to collapse
Did you do the downgrade to NCE through Odin first?
Yes I did. I tried it again and I see that I'm on NG3 now, I guess I have to do the other one Now.
juliusgy said:
Yes I did. I tried it again and I see that I'm on NG3 now, I guess I have to do the other one Now.
Click to expand...
Click to collapse
Once I was on NG3 I was able to upgrade using the OTA.
wildcard30 said:
Once I was on NG3 I was able to upgrade using the OTA.
Click to expand...
Click to collapse
I am on NG3 and I am not getting any OTA for OA1 which is 4.4.4! I need that to go to 5.0? How can I manually update it? Dont care for root and other gimmicks. Completely stock!
ThuGzta said:
I am on NG3 and I am not getting any OTA for OA1 which is 4.4.4! I need that to go to 5.0? How can I manually update it? Dont care for root and other gimmicks. Completely stock!
Click to expand...
Click to collapse
You could always try sideloading the NG3 to OA1 update then flashing through stock recovery from the other thread I mentioned.

[Q] Help me, please, Galaxy S5 stuck in bootloop and odin isn't flashing!

Help me XDA, you're my only hope!
In attempt to flash a custom recovery to my AT&T Galaxy S5 (SM-G900A), odin failed to flash it. After a while, I tried to root my phone after other forums/threads said I needed to. I tried towelroot, didn't work for $#!t. And the point of no return came when another forum said to flash a custom firmware to help TR, so I did. It failed. Then I decided to give up, but it got stuck in a bootloop, well, if you consider attempting to boot, giving up, and rebooting itself into bootloader a bootloop. And that was followed by attempting to flash stock firmware, which odin couldn't do anything. So, I've tried everything:
Kies won't detect my phone, or it will say it's unsupported
Odin must be broken or my phone is f***ed, because almost immediately, odin will say FAIL
Anti-Virus has been disabled this whole time
So if anyone reading this knows what they're doing, please help me out with this.
Matthew98405 said:
Help me XDA, you're my only hope!
In attempt to flash a custom recovery to my AT&T Galaxy S5 (SM-G900A), odin failed to flash it. After a while, I tried to root my phone after other forums/threads said I needed to. I tried towelroot, didn't work for $#!t. And the point of no return came when another forum said to flash a custom firmware to help TR, so I did. It failed. Then I decided to give up, but it got stuck in a bootloop, well, if you consider attempting to boot, giving up, and rebooting itself into bootloader a bootloop. And that was followed by attempting to flash stock firmware, which odin couldn't do anything. So, I've tried everything:
Kies won't detect my phone, or it will say it's unsupported
Odin must be broken or my phone is f***ed, because almost immediately, odin will say FAIL
Anti-Virus has been disabled this whole time
So if anyone reading this knows what they're doing, please help me out with this.
Click to expand...
Click to collapse
First off you need to give more info about your phone. What build are you on 5.0, 4.4.4 etc. How did you get on that build. Ota update or custom update. We can't really help you unless we know what your running.
dirtydodge said:
First off you need to give more info about your phone. What build are you on 5.0, 4.4.4 etc. How did you get on that build. Ota update or custom update. We can't really help you unless we know what your running.
Click to expand...
Click to collapse
I had 5.0 via OTA
Matthew98405 said:
I had 5.0 via OTA
Click to expand...
Click to collapse
I'll search and see what I can find. Try searching for the OC4 firmware. if I find something i'll post it here
Matthew98405 said:
Help me XDA, you're my only hope!
In attempt to flash a custom recovery to my AT&T Galaxy S5 (SM-G900A), odin failed to flash it. After a while, I tried to root my phone after other forums/threads said I needed to. I tried towelroot, didn't work for $#!t. And the point of no return came when another forum said to flash a custom firmware to help TR, so I did. It failed. Then I decided to give up, but it got stuck in a bootloop, well, if you consider attempting to boot, giving up, and rebooting itself into bootloader a bootloop. And that was followed by attempting to flash stock firmware, which odin couldn't do anything. So, I've tried everything:
Kies won't detect my phone, or it will say it's unsupported
Odin must be broken or my phone is f***ed, because almost immediately, odin will say FAIL
Anti-Virus has been disabled this whole time
So if anyone reading this knows what they're doing, please help me out with this.
Click to expand...
Click to collapse
if you can go into download mode then don't worry you can download another official firmware & flash it.
The firmware you tried & failed may be corrupt file so download new one & try.
Make sure your battery is more than 50%.if not know the battery level do not flash go to repair centre.
Sent from my SM-G900H using xda Forum
http://forum.xda-developers.com/att...w-to-unbrick-flash-to-stocknce-g900a-t3077652
You can try this. Make sure you are using Odin 3.09. You will need the OC4 stock partitions located at the bottom of the first post. That might work.
I just thought of this, does it matter what cable I use?
(Galaxy S5 USB 3.0 cable or standard micro USB)
Because I just used a regular cable and it worked!
Matthew98405 said:
I just thought of this, does it matter what cable I use?
(Galaxy S5 USB 3.0 cable or standard micro USB)
Click to expand...
Click to collapse
It don't matter. As long as Itty is a good working cable
Wait, now it's stuck on the AT&T logo.
Yay, I'm in
Now restoring
Matthew98405 said:
Wait, now it's stuck on the AT&T logo.
Yay, I'm in
Now restoring
Click to expand...
Click to collapse
So your back up and running now?
dirtydodge said:
So your back up and running now?
Click to expand...
Click to collapse
Yup, and I restored everything!
Any idea why odin kept failing to flash a custom recovery?
Matthew98405 said:
Yup, and I restored everything!
Any idea why odin kept failing to flash a custom recovery?
Click to expand...
Click to collapse
Because your running 5.0 ota. You can't root that version yet plus they only custom recovery that we have on the AT&T S5 is either safestrap or Flashfire which is still in testing faze. You'll need to wait til you can root the ota 5.0 since it has different bootloader.
Ok, thanks, so I can stop messing up my phone.
Matthew98405 said:
Wait, now it's stuck on the AT&T logo.
Yay, I'm in
Now restoring
Click to expand...
Click to collapse
How did you get it to restore? Im stuck at a soft brick on my s5 at&t with the 5.0 ota bootloader. Please help
---------- Post added at 07:48 AM ---------- Previous post was at 07:12 AM ----------
Matthew98405 said:
I had 5.0 via OTA
Click to expand...
Click to collapse
If u need help i found solution of the same problem. lemme know if u do
sir i have tried to downgrade my galaxy s5 at&t by odin
but odin fails and i,m still stuck on firmware error ..
what i can i do?
shreesam09 said:
sir i have tried to downgrade my galaxy s5 at&t by odin
but odin fails and i,m still stuck on firmware error ..
what i can i do?
Click to expand...
Click to collapse
What firmware were you on originally? Sounds like you we're on 5.0 or above . If so you will have to flash a pure stock rom of the same back to it . And no rooting for any thing above 4.4.4
Sent from my SM-G900F using XDA-Developers mobile app

MM Update (QI2) - TWRP Won't Install!!!

Hi,
I just got this phone (same phone I had to replace the one that died)::
Samsung Galaxy (SM-N910T) Note 4 (QualComm)
Marshmallow 6.0.1
It's Unlocked.
Anyway, before I could install TWRP so I could Root it, Android Firmware Updates started coming through. I figured let them install and that way I'd have them. I knew that if I tried to install them after installing TWRP, it would just replace TWRP anyway.
After the last Update, the Build is now...
Build #: MMB29M.N910T3UVU3EQI2
I have tried TWRP 3.0.2.0 & 2.8.7.0 and even PhilZ 6.59.0 but nothing will go on! Odin (latest and tried older one) starts to Flash it, it says "Recovery" and then it says, "FAIL".
I'm thinking it's gotta have something to do with the Updates to Marshmallow???
PLEASE HELP! I can't do anything that I need to do without it Rooted and I can't Root it without a Custom Recovery.
Thanks!
Dave
Zeuszoos said:
Hi,
I just got this phone (same phone I had to replace the one that died)::
Samsung Galaxy (SM-N910T) Note 4 (QualComm)
Marshmallow 6.0.1
It's Unlocked.
Anyway, before I could install TWRP so I could Root it, Android Firmware Updates started coming through. I figured let them install and that way I'd have them. I knew that if I tried to install them after installing TWRP, it would just replace TWRP anyway.
After the last Update, the Build is now...
Build #: MMB29M.N910T3UVU3EQI2
I have tried TWRP 3.0.2.0 & 2.8.7.0 and even PhilZ 6.59.0 but nothing will go on! Odin (latest and tried older one) starts to Flash it, it says "Recovery" and then it says, "FAIL".
I'm thinking it's gotta have something to do with the Updates to Marshmallow???
PLEASE HELP! I can't do anything that I need to do without it Rooted and I can't Root it without a Custom Recovery.
Thanks!
Dave
Click to expand...
Click to collapse
From what I know, the bootloader isn't locked but I recommend installing a KitKat bootloader Using this thread
https://forum.xda-developers.com/no...ws-want-to-downgrade-to-4-4-4-kitkat-t3447773
From there you can install TWRP and/or update to qg1, qe2, or older.
dottyparent said:
From what I know, the bootloader isn't locked but I recommend installing a KitKat bootloader Using this thread
https://forum.xda-developers.com/no...ws-want-to-downgrade-to-4-4-4-kitkat-t3447773
From there you can install TWRP and/or update to qg1, qe2, or older.
Click to expand...
Click to collapse
First, thank you for responding!
I used that page on my last Note 4 (it died, hardware failure), after I tried MM but hated the Ext SD handling and so I went back down to the T2 KK ROM on that page and it worked fine (I installed the entire ROM). But my replacement Note 4 that just arrived already had MM as I said and updated to a Build # I haven't seen.
But if you look at the Build #, T-Mobile seems to have (via the Updates) turned the phone into a "N910T3" instead of a "N910T". Weird! Especially since I'm with MetroPCS. Hahaha! They're owned by T-Mobile though, use the same Towers, etc..
Anyway, I'd like to try and stick with MM this time around.
But you did hit one of my grey areas.
Let me see if I understand you correctly... If I were to Flash just the KK BL, my phone would/would not continue to Boot into Marshmallow as it is now, if I Flashed nothing but that?
Or am I correct in saying that your method would mean taking the phone back, so that it would be running KitKat and then going back up to Marshmallow using a different ROM that TWRP will be able to go onto?
The reason I'm fuzzy, is because I've never Flashed just a BootLoader, so I'm not sure what would happen if I Flash just the KK BootLoader onto an MM ROM and Reboot???
Thank you again for your time!
Zeuszoos said:
First, thank you for responding!
I used that page on my last Note 4 (it died, hardware failure), after I tried MM but hated the Ext SD handling and so I went back down to the T2 KK ROM on that page and it worked fine (I installed the entire ROM). But my replacement Note 4 that just arrived already had MM as I said and updated to a Build # I haven't seen.
But if you look at the Build #, T-Mobile seems to have (via the Updates) turned the phone into a "N910T3" instead of a "N910T". Weird! Especially since I'm with MetroPCS. Hahaha! They're owned by T-Mobile though, use the same Towers, etc..
Anyway, I'd like to try and stick with MM this time around.
But you did hit one of my grey areas.
Let me see if I understand you correctly... If I were to Flash just the KK BL, my phone would/would not continue to Boot into Marshmallow as it is now, if I Flashed nothing but that?
Or am I correct in saying that your method would mean taking the phone back, so that it would be running KitKat and then going back up to Marshmallow using a different ROM that TWRP will be able to go onto?
The reason I'm fuzzy, is because I've never Flashed just a BootLoader, so I'm not sure what would happen if I Flash just the KK BootLoader onto an MM ROM and Reboot???
Thank you again for your time!
Click to expand...
Click to collapse
This method will turn your phone temporarily to a t2, of which a mm Rom will not boot. Since your goal is to have TWRP on a MM Rom, I would do the following:
1. Flash the t2 KK bootloader.
2. Find your appropriate KK bootloader (ie if you have a 910t find a 910t bootloader) and flash it
3. Flash TWRP
4. Flash a MM bootloader and modem.
dottyparent said:
This method will turn your phone temporarily to a t2, of which a mm Rom will not boot. Since your goal is to have TWRP on a MM Rom, I would do the following:
1. Flash the t2 KK bootloader.
2. Find your appropriate KK bootloader (ie if you have a 910t find a 910t bootloader) and flash it
3. Flash TWRP
4. Flash a MM bootloader and modem.
Click to expand...
Click to collapse
Is this a method you've tried B4?
I'll check out that thread and see if they've got an MM Modem too.
Isn't that the "EFS" part of a ROM? If so, there are EFS Backup apps. But they may require Root though.
TTYL
Zeuszoos said:
Is this a method you've tried B4?
I'll check out that thread and see if they've got an MM Modem too.
Isn't that the "EFS" part of a ROM? If so, there are EFS Backup apps. But they may require Root though.
TTYL
Click to expand...
Click to collapse
Yes I have tried this. I changed my phone from a trip to a t2 and back again.
dottyparent said:
This method will turn your phone temporarily to a t2, of which a mm Rom will not boot. Since your goal is to have TWRP on a MM Rom, I would do the following:
1. Flash the t2 KK bootloader.
2. Find your appropriate KK bootloader (ie if you have a 910t find a 910t bootloader) and flash it
3. Flash TWRP
4. Flash a MM bootloader and modem.
Click to expand...
Click to collapse
dottyparent said:
Yes I have tried this. I changed my phone from a trip to a t2 and back again.
Click to expand...
Click to collapse
There is an MM ROM that is Rooted and has TWRP built in, but I don't know if it would Flash over this with Odin or not
I am also considering trying the entire KK T2 ROM again to go down to KK and then Flashing that MM ROM.
It has both Odexed & DeOdexed. If I remember right, DeOdexed is the better choice, right?
Thanks for all your time and help!
Dave
Hi,
You know what's sad, is that if I could somehow Roog it without TWRP, then I could use the way awesome "Flashify" app to try to get TWRP on this phone! <lol>
Dave
dottyparent said:
From what I know, the bootloader isn't locked but I recommend installing a KitKat bootloader Using this thread
https://forum.xda-developers.com/no...ws-want-to-downgrade-to-4-4-4-kitkat-t3447773
From there you can install TWRP and/or update to qg1, qe2, or older.
Click to expand...
Click to collapse
dottyparent said:
Yes I have tried this. I changed my phone from a trip to a t2 and back again.
Click to expand...
Click to collapse
Could you please tell me where the files are that you used, so that I can have the exact same ones to work with? I looked at the link you provided, but I couldn't find just the BootLoader in it. I saw where someone requested just the BootLoader and Modem (you?) and "Trex888" said he would upload them right away and provide a link, but I did not see one ever posted. Just the link for the entire ROM.
Btw, in Odin, if you're Flashing only the BootLoader, do you use the "BL" button instead of the "AP" (formerly "PDA") button? What about just the Modem (thru Recovery?)?
I just tried Flashing the entire T2 KK ROM that I had used to go back from MM to KK on my first Note 4, but this one wouldn't take that either. It immediately said "FAIL".
I'm sorry if I'm a pain. It's just that I'm disabled and constantly laying on my side, so a laptop is out for regular use and so this phone is my main and only communication with the outside world. What I'm saying is that it's not a hobby phone and I have to get it right, because (see below). So I don't want to Flash something that may not do it, so I want to exactly match what you did.
You see, I can only sit up to Flash from Odin on my Windows computer with my phone cabled to it for just so long because of my condition.
Not your problem, I know. But I'm explaining it to you so that you can understand that I'm not just trying to be lazy. But instead, I need to make sure I do exactly what worked for you, with exactly those files, because if something goes wrong, it could take me days of short time computer access due to my situation (too much overwhelming pain) to figure it out and get it (hopefully) fixed. So you can see the importance, no doubt.
This phone right now (see Build #) says it's a T3, but whatever works.
Right now, it's without Recovery so I can't Root it, so I can't get Write access to my Ext SD, etc.. I need to Root!
Also, this T3 MM ROM is having issues with the Display. Sometimes it'll get all chopped up and I have to Reboot.
So anyway, I need to get this done and I would very much appreciate your further help!
Thank You!!!
Dave
Zeuszoos said:
Could you please tell me where the files are that you used, so that I can have the exact same ones to work with? I looked at the link you provided, but I couldn't find just the BootLoader in it. I saw where someone requested just the BootLoader and Modem (you?) and "Trex888" said he would upload them right away and provide a link, but I did not see one ever posted. Just the link for the entire ROM.
Btw, in Odin, if you're Flashing only the BootLoader, do you use the "BL" button instead of the "AP" (formerly "PDA") button? What about just the Modem (thru Recovery?)?
I just tried Flashing the entire T2 KK ROM that I had used to go back from MM to KK on my first Note 4, but this one wouldn't take that either. It immediately said "FAIL".
I'm sorry if I'm a pain. It's just that I'm disabled and constantly laying on my side, so a laptop is out for regular use and so this phone is my main and only communication with the outside world. What I'm saying is that it's not a hobby phone and I have to get it right, because (see below). So I don't want to Flash something that may not do it, so I want to exactly match what you did.
You see, I can only sit up to Flash from Odin on my Windows computer with my phone cabled to it for just so long because of my condition.
Not your problem, I know. But I'm explaining it to you so that you can understand that I'm not just trying to be lazy. But instead, I need to make sure I do exactly what worked for you, with exactly those files, because if something goes wrong, it could take me days of short time computer access due to my situation (too much overwhelming pain) to figure it out and get it (hopefully) fixed. So you can see the importance, no doubt.
This phone right now (see Build #) says it's a T3, but whatever works.
Right now, it's without Recovery so I can't Root it, so I can't get Write access to my Ext SD, etc.. I need to Root!
Also, this T3 MM ROM is having issues with the Display. Sometimes it'll get all chopped up and I have to Reboot.
So anyway, I need to get this done and I would very much appreciate your further help!
Thank You!!!
Dave
Click to expand...
Click to collapse
Okay. Here is what I did exactly.
Download my Files here: https://1drv.ms/f/s!AJEa3D0cBAhIbQ
Stock 910T files here https://androidfilehost.com/?w=files&flid=20602
i guess if you need any other stock files sammobile works.
This will reset your phone!
1) Odin flash the AOG1 file. this turns the phone into a t2 phone.
2) Odin the ANK4 rom. this returns the phone to a 910t.
3) Boot into the ANK4 rom and download the MM update. This should land you on the first MM update, EPE3
4) Flash TWRP, thourgh AP, which should work. Might as well flash superSU or magisk.
At this point i would wipe everything and install a custom rom, but you could update to a newer boot loader and modem using the BL and CP buttons, respectively.
hope this helps
dottyparent said:
Okay. Here is what I did exactly.
Download my Files here: https://1drv.ms/f/s!AJEa3D0cBAhIbQ
Stock 910T files here https://androidfilehost.com/?w=files&flid=20602
i guess if you need any other stock files sammobile works.
This will reset your phone!
1) Odin flash the AOG1 file. this turns the phone into a t2 phone.
2) Odin the ANK4 rom. this returns the phone to a 910t.
3) Boot into the ANK4 rom and download the MM update. This should land you on the first MM update, EPE3
4) Flash TWRP, thourgh AP, which should work. Might as well flash superSU or magisk.
At this point i would wipe everything and install a custom rom, but you could update to a newer boot loader and modem using the BL and CP buttons, respectively.
hope this helps
Click to expand...
Click to collapse
Thank you for responding!
The OG1 is the T2 ROM that I had just tried and reported that unlike my previous Note 4, it would not Flash on this one to turn it into a KK T2. I also tried the other 2 ROMS to no avail.
I think it's because this one says it's a T3.
Thanks,
Dave
Zeuszoos said:
Thank you for responding!
The OG1 is the T2 ROM that I had just tried and reported that unlike my previous Note 4, it would not Flash on this one to turn it into a KK T2. I also tried the other 2 ROMS to no avail.
I think it's because this one says it's a T3.
Thanks,
Dave
Click to expand...
Click to collapse
I'm sorry man I did everything that I could think of. I knew that the T3 had a few issues with bootloaders and downgrading and stuff, but wow, i didn't know about these issues. Good luck with trying something else then.
dottyparent said:
I'm sorry man I did everything that I could think of. I knew that the T3 had a few issues with bootloaders and downgrading and stuff, but wow, i didn't know about these issues. Good luck with trying something else then.
Click to expand...
Click to collapse
No, I'm sorry, but you have to give me the answer.
All seriousness aside, I depreciate all your effort.
I can only think of one thing left to try... Go to Sammy's site and get the Lollipop 5.1.1 ROM and see what happens. It can't hurt to try, right?
I'll let ya know what happens and thank you again!
Happy Thanksgiving!
Dave
dottyparent said:
I'm sorry man I did everything that I could think of. I knew that the T3 had a few issues with bootloaders and downgrading and stuff, but wow, i didn't know about these issues. Good luck with trying something else then.
Click to expand...
Click to collapse
Guess what? I decided to take a picture of my phone's screen after it Failed to let me Flash anything at all in Odin. I tried TWRP again and this time read what my phone responds with and it says the following:
Custom Binary (Recovery) Blocked By FRP LOCK
Does that mean anything to you?
TTYL
Zeuszoos said:
Guess what? I decided to take a picture of my phone's screen after it Failed to let me Flash anything at all in Odin. I tried TWRP again and this time read what my phone responds with and it says the following:
Custom Binary (Recovery) Blocked By FRP LOCK
Does that mean anything to you?
TTYL
Click to expand...
Click to collapse
Well I searched around XDA and it seems to be a problem exclusive to the T3. Try going to settings -> security and see if there is a option to disable resetting protection. Or see if there is a way to disable OEM locking. However it's probably not there. The only successful thread I found was this
https://forum.xda-developers.com/note-4/help/note-4-t-mobile-sm-n910t3-custom-binary-t3346840
---------- Post added at 07:28 PM ---------- Previous post was at 07:24 PM ----------
If all else doesn't work, perhaps you could repartition your phone. You need a pit file and a few ROMs
Zeuszoos said:
Hi,
I just got this phone (same phone I had to replace the one that died)::
Samsung Galaxy (SM-N910T) Note 4 (QualComm)
Marshmallow 6.0.1
It's Unlocked.
Anyway, before I could install TWRP so I could Root it, Android Firmware Updates started coming through. I figured let them install and that way I'd have them. I knew that if I tried to install them after installing TWRP, it would just replace TWRP anyway.
After the last Update, the Build is now...
Build #: MMB29M.N910T3UVU3EQI2
I have tried TWRP 3.0.2.0 & 2.8.7.0 and even PhilZ 6.59.0 but nothing will go on! Odin (latest and tried older one) starts to Flash it, it says "Recovery" and then it says, "FAIL".
I'm thinking it's gotta have something to do with the Updates to Marshmallow???
PLEASE HELP! I can't do anything that I need to do without it Rooted and I can't Root it without a Custom Recovery.
Thanks!
Dave
Click to expand...
Click to collapse
That's weird. I updated my N910T to EQI2 with Odin, rooted using CF-Auto-Root for N910T and then flashed TWRP 3.1.1 and I had no problems at all
dottyparent said:
I'm sorry man I did everything that I could think of. I knew that the T3 had a few issues with bootloaders and downgrading and stuff, but wow, i didn't know about these issues. Good luck with trying something else then.
Click to expand...
Click to collapse
ShaDisNX255 said:
That's weird. I updated my N910T to EQI2 with Odin, rooted using CF-Auto-Root for N910T and then flashed TWRP 3.1.1 and I had no problems at all
Click to expand...
Click to collapse
But you updated to it. From KK?
KK doesn't have it and it's not in downloadable ROMS.
But if MM is already on the phone (mine), then it has FRP. See my other response.
TTYL
Zeuszoos said:
But you updated to it. From KK?
KK doesn't have it and it's not in downloadable ROMS.
But if MM is already on the phone (mine), then it has FRP. See my other response.
TTYL
Click to expand...
Click to collapse
That's because I have a n910t not a t3
Zeuszoos said:
But you updated to it. From KK?
KK doesn't have it and it's not in downloadable ROMS.
But if MM is already on the phone (mine), then it has FRP. See my other response.
TTYL
Click to expand...
Click to collapse
I upgraded from LL. The device was running 5.0.1 and now has 6.0.1
dottyparent said:
Well I searched around XDA and it seems to be a problem exclusive to the T3. Try going to settings -> security and see if there is a option to disable resetting protection. Or see if there is a way to disable OEM locking. However it's probably not there. The only successful thread I found was this
https://forum.xda-developers.com/note-4/help/note-4-t-mobile-sm-n910t3-custom-binary-t3346840
---------- Post added at 07:28 PM ---------- Previous post was at 07:24 PM ----------
If all else doesn't work, perhaps you could repartition your phone. You need a pit file and a few ROMs
Click to expand...
Click to collapse
Thank you for looking! I found out what it is.
It's "Factory Reset Protection" (FRP)
What it does, is keep someone else from Factory Resseting your phone if they steal it. When they reset it, during setup, they have to type in the last Google Email and Password that the phone used, before they can set up theirs.
After reading that, I remembered having to put my Google Info in at two separate points and seeing it telling me to "Verify", but I was just blowing right through setup, not reading all of the small print. I mean hey, I had no idea that even existed and was just annoyed that I had to type the same thing twice!
It will only be found on phones that already have Lollipop and up on them out of the box and probably not all of them yet. And you don't have to worry about downloadable ROMS, so those who have phones that started with KitKat, or even early versions of Marshmallow 6.0 or 6.0.1 would not have seen this happen to them. Even those who updated to the same version of Mm that my phone has won't, if they started with KK or an older MM and then updated to it.
Again, this is something that your phone would have "Out of the Box" and the phone (not all) would have at least L on it.
Just FYI, it's not just Samsung, either.
Just FYI, I have confirmed this info. It is a fact.
Once I have an easy to do, working fix, hopefully without having to perform a Factory Reset, I will "Create A Thread" and as normal for me, write clear and easy, step by step (not leaving any out) instructions on how to "Unlock FRP" and then come back here and post a link to the thread. Hopefully this week.
This phone will not beat me!!!
TTYL
Dave

Categories

Resources