Related
I have numerous chargers at home all of which have charged my evo, gs2, Nexus 7, etc.
Can these be used interchangeable in the Note 2 without harming the charging process?
Thanks
As long as the Voltage is the same (5V) there is no Problem. But you should have a charger at 2 Amper for optimal charging speed.
I just tried charging mine with the normal microUSB charger I use for every other phone I have had and it took 7.5 hours to charge from 5%-62%. I used the stock charger that was in the box and it charged it in 3.5-4 hours no problem. Seems like the charger in the box charges faster.
reading this thread made me curious, my NOTE II should arrive in about a week, I can't tell for myself yet, what is the A (amps) specification mentioned on the original charger?
as i come from HTC, my current chargers go up to 1 A current. witch is the double A a standard USB port will give unless crossover'd .
thanks in advance!
----
in the wiki thread i found the answer, the supplied charger delivers 5 V 2 A output to the device.
WendigoNL said:
what is the A (amps) specification mentioned on the original charger?
Click to expand...
Click to collapse
2A! Same as the Tab 10.1 charger.
Filling a 3100mAh battery requires some grunt.
i think even the usb cable makes a difference..
when i use the stock usb cable with the stock charger ..my s3 would charge up comparatively faster than with the other usb cable connected to the same stock charger.:rolleyes
max.android said:
i think even the usb cable makes a difference..
Click to expand...
Click to collapse
It certainly does! :good:
All electrical cables have some resistance. Very low (but not zero) for quality cables, sometimes quite noticeable for thin and cheap offerings.
From Ohm's Law we know that voltage drop will be proportional to current. A cable with a resistance of just half an ohm will loose about 0.5% at 50mA. That's pretty much nothing. However, at 2000mA the loss reaches 20%.
dude use any charger, just don't use LG charger **** !!!!!
You must use the 5volt 2amp charger and cable provided or a replacement with the same output or youll either be waiting for ever for it to charge or do some damage.
I tryed using my note 1 charger rated at 1amp and guess what? It took about twice as long to charge.
Sent from my GT-N7100 using xda app-developers app
Some of my old 1 Amp chargers aren't happy at all, and will often decide to stop charging randomly.
I though it was something weird with my phone, but after switching chargers it never happened again.
- Frank
USA official charger
This are the images of the official USA charger that will comes when they release the device in USA
And yes its a 2.0A charger, so the SIII charger isn't appropriate for NoteII.
this is the kind of charger used in Canada, USA, and Latin America, i bought this NoteII in Mexico from an authorized Samsung provider, of course factory unlocked 710usd, like 10,900mxn.
Has anyone tried a 3A charger? Just wondering if this would speed up charging even more than the standard 2A charger.
mcdill the pig said:
Has anyone tried a 3A charger? Just wondering if this would speed up charging even more than the standard 2A charger.
Click to expand...
Click to collapse
No, it won't speed it up. It's what the device takes from a charger, and not what a charger can potentially supply. If the device's charging circuit is spec'd for up to 2A current, that's what it will suck out of a charger, not more. You can connect a 30A lab power supply, and it will still be the same 2A (or less) input. To speed up the charging process, you need to mod the charging circuit of the device itself.
Hey Everyone,
It's become kinda obvious now that i really need to change out all my old 1A chargers for 2A chargers now.
The one that comes with the phone is nice - if I didn't need the adapter to go with it. Now it's huge and chunk.
I'd like a pretty small charger, like the wonderful 1A TC U260 I got with my mytouch 4g.
I'm considering the following:
PowerGen Dual USB 2A 10W Car charger:
http://www.amzn.com/gp/product/B006...=1789&creative=390957&creativeASIN=B006SU0SX0
PowerGen Dual Port Travel Wall Charger
http://www.amazon.com/PowerGen-Travel-Charger-Samsung-included/dp/B0073FE1F0/ref=cm_cr_dp_asin_lnk
Griffin GC23139 PowerJolt Dual car charger
http://www.amazon.com/Griffin-GC231...e=UTF8&qid=1349479987&sr=1-1&keywords=GC23139
(I really liked their dual mini which I used for a long time)
Any recommendations?
That first wall charger looks like something I'd buy. The charger and adapter I got from handtec is just so huge and ugly
Sent from my SAMSUNG-SGH-I717 using Tapatalk 2
How about the old HP touchpad chargers. IIRC those are 2a chargers. And they are cheap
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
I bought this one. Have not recieved it yet but looks good on paper.
http://pages.ebay.com/link/?nav=item.view&id=170905466556
Sent from my GT-N7100 using xda app-developers app
This is kinda related to this thread
Can I use another USB cable with the original note 2 charger and still get 2A from it? I feel like the USB cables for my sgs2 fit better in my note 2 than the one that comes with it.
none of those car chargers will work if you plan on using the phone
ChodTheWacko said:
Hey Everyone,
It's become kinda obvious now that i really need to change out all my old 1A chargers for 2A chargers now.
The one that comes with the phone is nice - if I didn't need the adapter to go with it. Now it's huge and chunk.
I'd like a pretty small charger, like the wonderful 1A TC U260 I got with my mytouch 4g.
I'm considering the following:
PowerGen Dual USB 2A 10W Car charger:
PowerGen Dual Port Travel Wall Charger
Griffin GC23139 PowerJolt Dual car charger
(I really liked their dual mini which I used for a long time)
Any recommendations?
Click to expand...
Click to collapse
I have done a lot of research on this. If it is compatible with ANY apple products then it will not charge with your cable due to the USB standard not being the same. You will have to either mod the product or the cable to get the full 2a charge. Plus I believe the Powergen and the griffin are only 2a total output so if you are charging 2 devices it will only be 1a and 1a ports. You need to look for a 4a total output. I have yet to find any that work. If anyone can find one please let me know. Charging with a 1a charge and using a GPS you will lose power as it does not charge fast enough. You need a full 2a. p.s. had to remove the outside links because I havent posted 10x yet.
yankees177 said:
If it is compatible with ANY apple products then it will not charge with your cable due to the USB standard not being the same.
Click to expand...
Click to collapse
This is not quite true.
I believe Apple only has high speed charging if you don't use an 'apple' USB port, similar to how you don't get high speed charging if you use a USB data cable versus a charging cable.
To be 100% I don't understand how it works exactly.
I can tell you, however, the following:
1) My Griffin charger happily charged my galaxy note even going full blast (GPS/bluetooth/screen on), and I bought some iphone chargers to help my friends out, and they charged their phones (slowly) with my charger too.
2) The powergen 10W charger I put above also happily (and quickly) charges my Note II going full blast.
It actually has a different 'Apple' vs 'non apple' USB port. Non-apple stuff may not charge in the apple slot, but that's not a big deal to me. I have only one phone. My iphone friends are usually the ones running out of power anyway, so it's kind of nice one side is applely.
- Frank
to the OP, try this:
http://www.amzn.com/Mediabridge-Hig...&qid=1351550361&sr=1-12&keywords=powergen+3.1
then get a charging cable:
http://www.amzn.com/Naztech-Micro-U...1351550441&sr=1-2&keywords=usb+charging+cable
or if you have an extra cable lying around, mod it. See this post to get a better idea:
http://forum.xda-developers.com/showpost.php?p=22546114&postcount=1
Thread linked for reference:
http://forum.xda-developers.com/showthread.php?t=1686971
I have many 2a carchargers that worked great with a gs3 even an iPad that won't provide enough juice to the note to actually charge it while doing intensive tasks like mhl out in the car.
if anyone finds a car charger that actually works post it out we need a fast charge custom kernel.
I have a thread in the general note Sprint forum thatwe are discussing this as well and it seems no charger will work but an adapter I'm waiting on May
what about this?
http://www.amazon.com/gp/product/B00845NI8E/ref=oh_details_o00_s00_i00
dual 2A port car charger and comes with a Free MicroUSB cable that can handle faster charging. I ordered on so we'll see
peekeesh said:
to the OP, try this:
http://www.amzn.com/Mediabridge-Hig...&qid=1351550361&sr=1-12&keywords=powergen+3.1
This appears, from the reviews, to be an "apple"ish charger and doesn't work well with android devices.
Click to expand...
Click to collapse
Would this work?
http://pages.ebay.com/link/?nav=item.view&id=150928933202
yankees177 said:
I have done a lot of research on this. If it is compatible with ANY apple products then it will not charge with your cable due to the USB standard not being the same. You will have to either mod the product or the cable to get the full 2a charge. Plus I believe the Powergen and the griffin are only 2a total output so if you are charging 2 devices it will only be 1a and 1a ports. You need to look for a 4a total output. I have yet to find any that work. If anyone can find one please let me know. Charging with a 1a charge and using a GPS you will lose power as it does not charge fast enough. You need a full 2a. p.s. had to remove the outside links because I havent posted 10x yet.
Click to expand...
Click to collapse
Im looking for 2A on each port too wall charger and only finds these.
Car charger:
http://www.amazon.com/Qmadix-QM-DMCH4-2-AP-WH-Twin-Tablet-Charging/dp/B008AGMO7S/ref=pd_cp_e_1
Wall charger, but thinks it divides 4A on each port?
http://www.alibaba.com/product-gs/650723185/UL_Approval_4A_USB_Charger_For.html
Wall charger:
http://www.thinkgeek.com/product/efbe/#tabs
Why the heck are all for ipads, iphone and no EU plug.
I got an amazon branded 2A single usb charger about 6 months ago for another phone. It charges my Note2 quick. Sorry no links...
Sent from my SGH-T889 using Tapatalk 2
What about this please? Need input.
i.Sound Portable Charger
Has 16,000 mah
Input: 12V 1A
Output: ''5V 2.1A on each connector 2.5 A together''
I charge a number of things on here...
A friend has me a bit confused saying this could damage the charging mechanisms of the phone cause it has too much voltage?
Any input please?
Thanks
One Car Charger that works
Hello,
Whether a charger works or not depends on what DCP (Direct Charge Port) modes it supports.
I suspect the GN2 uses Shorted DCP, where the USB data lines (D+ and D-) are shorted. Apple chargers sense 2.4Vdc on these lines to allow the charger to ramp to full current. Asus and some Sammy TABs use 1.2Vdc to enable full current. This is to distinguish real USB ports from chargers, and to "encourage" you to use the manufacturer's provided charger.
It would be nice if someone can confirm what DCP mode the GN2 actually uses. Not that the charger manufacturer's publish what modes they support.... However, the charger IC manufacturer's (TI, Maxim) are beginning to get good at DCP autodetection which is going to make it much easier for us consumers.
As far as finding chargers that work,
I bought a 2.1A dual car charger at Walmart, model "i-xt" that works well with the GN2 and is listed as "on AC" when connected. Implying full current.
Cheers,
-Plaz
---------- Post added at 12:43 PM ---------- Previous post was at 12:31 PM ----------
rockky said:
i.Sound Portable Charger
Has 16,000 mah
Input: 12V 1A
Output: ''5V 2.1A on each connector 2.5 A together''
I charge a number of things on here...
A friend has me a bit confused saying this could damage the charging mechanisms of the phone cause it has too much voltage?
Any input please?
Thanks
Click to expand...
Click to collapse
You don't have to worry about your phone being damaged. Phones have built-in protection for over-voltage and over current. 5Vdc is proper voltage for USB devices anyway (Output 5V, as listed in the specs). The catch is if the phone allows full current charging. That depends on the DCP mode of the charger. I'm not positive what mode the GN2 truly supports. If you already have the charger, you can determine if full current is being used by checking under settings -> battery while connected to the charger. If you see the "On AC" verbiage, the phone is in full current mode. If not, the charger is limiting to 500ma and acts like a standard USB port. You phone will still charge, but it will take longer.
Clear as mud?
Cheers,
-Plaz
http://www.amazon.co.uk/dp/B0044E7MNG/ref=cm_sw_r_an_am_ap_am_gb?ie=UTF8
Would this work?
Sent from my GT-N7105 using Tapatalk 2
Thanks
QUOTE=Plazmid;33523324]Hello,
Whether a charger works or not depends on what DCP (Direct Charge Port) modes it supports.
I suspect the GN2 uses Shorted DCP, where the USB data lines (D+ and D-) are shorted. Apple chargers sense 2.4Vdc on these lines to allow the charger to ramp to full current. Asus and some Sammy TABs use 1.2Vdc to enable full current. This is to distinguish real USB ports from chargers, and to "encourage" you to use the manufacturer's provided charger.
It would be nice if someone can confirm what DCP mode the GN2 actually uses. Not that the charger manufacturer's publish what modes they support.... However, the charger IC manufacturer's (TI, Maxim) are beginning to get good at DCP autodetection which is going to make it much easier for us consumers.
As far as finding chargers that work,
I bought a 2.1A dual car charger at Walmart, model "i-xt" that works well with the GN2 and is listed as "on AC" when connected. Implying full current.
Cheers,
-Plaz
---------- Post added at 12:43 PM ---------- Previous post was at 12:31 PM ----------
You don't have to worry about your phone being damaged. Phones have built-in protection for over-voltage and over current. 5Vdc is proper voltage for USB devices anyway (Output 5V, as listed in the specs). The catch is if the phone allows full current charging. That depends on the DCP mode of the charger. I'm not positive what mode the GN2 truly supports. If you already have the charger, you can determine if full current is being used by checking under settings -> battery while connected to the charger. If you see the "On AC" verbiage, the phone is in full current mode. If not, the charger is limiting to 500ma and acts like a standard USB port. You phone will still charge, but it will take longer.
Clear as mud?
Cheers,
-Plaz[/QUOTE]
I bought this:
http://www.amazon.com/gp/product/B005AWO8V0/
It's 2A and works great. I like that the cord is attached, so no losing a USB cable or anything. Also has an integrated USB for other devices.
Plazmid said:
Hello,
Whether a charger works or not depends on what DCP (Direct Charge Port) modes it supports.
I suspect the GN2 uses Shorted DCP, where the USB data lines (D+ and D-) are shorted. Apple chargers sense 2.4Vdc on these lines to allow the charger to ramp to full current. Asus and some Sammy TABs use 1.2Vdc to enable full current. This is to distinguish real USB ports from chargers, and to "encourage" you to use the manufacturer's provided charger.
It would be nice if someone can confirm what DCP mode the GN2 actually uses. Not that the charger manufacturer's publish what modes they support.... However, the charger IC manufacturer's (TI, Maxim) are beginning to get good at DCP autodetection which is going to make it much easier for us consumers.
As far as finding chargers that work,
I bought a 2.1A dual car charger at Walmart, model "i-xt" that works well with the GN2 and is listed as "on AC" when connected. Implying full current.
Cheers,
-Plaz
---------- Post added at 12:43 PM ---------- Previous post was at 12:31 PM ----------
You don't have to worry about your phone being damaged. Phones have built-in protection for over-voltage and over current. 5Vdc is proper voltage for USB devices anyway (Output 5V, as listed in the specs). The catch is if the phone allows full current charging. That depends on the DCP mode of the charger. I'm not positive what mode the GN2 truly supports. If you already have the charger, you can determine if full current is being used by checking under settings -> battery while connected to the charger. If you see the "On AC" verbiage, the phone is in full current mode. If not, the charger is limiting to 500ma and acts like a standard USB port. You phone will still charge, but it will take longer.
Clear as mud?
Cheers,
-Plaz
Click to expand...
Click to collapse
So I understand the shorting D+/D- internally or via charging cable to enable "AC" charging. I understand that Apple and apparently Sammy/Asus use voltage on those lines to signal the requirement for full current. Here's my question: if my Note2 is connected to brand X charger and it says AC charging in the settings under battery, does that mean I am theoretically pulling the max current of that brand X charger. This of course assumes the battery is empty enough, temperatures of the battery and charger are low enough, etc...
What I'm getting at is does having a shorted charger or cable with an android on an iCharger give us full iPower? Gawd that sounds horrible doesn't it! :silly: Or, if you're getting "AC" from the iCharger is it really only 1.1A or 1.6A (just tossing those numbers out there) vice the 2.1A it would be charging an iPad at?
Hi,
I've got my phone with samsung's charger of 1A (bought it from an open store locally - it was the cheapest), so I ordered a Sony Ericsson charger of 1.5A which charges up much faster..
My question is, could it goes even faster?
I've seen some Galaxy Note 2 and S 4 charger of 2A like these:
http://www.ebay.com/itm/2A-USB-Wall...S_Cell_Phone_PDA_Chargers&hash=item5658d7a0bd
http://www.ebay.com/itm/OEM-2A-USB-...l_Phone_PDA_Chargers&var=&hash=item51aabf953a
Could our phone handle it and charge it with the whole 2A power? could it ruin the battery with that high Ampere?
I'm asking this because I've ordered a docking station like this:
http://www.ebay.com/itm/261247762140?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
Which says 1.6A, so I was thinking perhaps theres stronger chargers out there for it..
Thanks!
im not sure about this but i believe the charger that comes with the phone is a 2 amp charger
It can handle 2A through USB port.
Via the charging dock, it can take 1.8A. Is that dock you are linking to an original part?
I have two DK26 docks and both say 1.8A, not 1.6A. Although if you connect a 2A charger to the dock, it'll be fine, it just won't be using the whole 2A input.
skinsfanbdh said:
im not sure about this but i believe the charger that comes with the phone is a 2 amp charger
Click to expand...
Click to collapse
I've never seen a Sony's charger with 2Amp, do you mind to picture the detailed information in the back of your charger please?
DrKrFfXx said:
It can handle 2A through USB port.
Via the charging dock, it can take 1.8A. Is that dock you are linking to an original part?
I have two DK26 docks and both say 1.8A, not 1.6A,
Click to expand...
Click to collapse
The Dock I've linked is a chinese copy, not the original, the one says 1.6A on description on Ebay, Does your original DK26 dock comes with charger too? What input and output is it says on each one? (picture could help much)
Also, how do you know it can handle 2A through USB? is that for sure?
Thanks for both!
The docks come barebone. No chargers included.
The charger included on the box of the phone is rated at 1.5A.
I have a Nexus 7 2A charger and an old Nokia 1.2A charger aside from the included 1.5A charger. All work fine either via USB or via the dock.
I can't notice any mayor difference on charging times, though. 1.2A charges almost as if not as fast as the 2A one. Iphone's 1A chargers do seem to take like 4 hours to charge the phone compared to the standard 2.5h I get from other higher rated wall chargers.
There are no 2A Sony chargers as of now.
DrKrFfXx said:
The docks come barebone. No chargers included.
The charger included on the box of the phone is rated at 1.5A.
I have a Nexus 7 2A charger and an old Nokia 1.2A charger aside from the included 1.5A charger. All work fine either via USB or via the dock.
I can't notice any mayor difference on charging times, though. 1.2A charges almost as if not as fast as the 2A one. Iphone's 1A chargers do seem to take like 4 hours to charge the phone compared to the standard 2.5h I get from other higher rated wall chargers.
There are no 2A Sony chargers as of now.
Click to expand...
Click to collapse
I see, I think I've cleared my doubts and I shell buy this 2A samsungs charger..
Thanks!
mcjordan92 said:
I see, I think I've cleared my doubts and I shell buy this 2A samsungs charger..
Thanks!
Click to expand...
Click to collapse
I'm using a 2A as my car charger works perfect.
Sent from my C6603 using Tapatalk 2
It should handel 2.A but I won't remand it. I don't think it's good for battery. But one thing is pretty sure. The phone will heat more up as the charging circuit have to dissipate more excess power. Can not affirm it as I don't exactly know it's made but I'm just saying...
"I know that my English isn't perfect, but I still hope it's comprehensible." Send over the cool Xperia Z
The downside would be possibly shortening the usable life of your battery, because the higher amp charging will likely heat the battery to a higher temp.
There's no free lunch.
To me, waiting a bit longer for charging is worth it to ensure the longest charge cycle life, particularly since the battery is sealed into the device. If it was a cheap and easy replaceable battery, maybe.
Amps don't matter unless it is lower than the specification
Think about your car battery having 700amps but your car stereo is fused for 20amps. Your car stereo gets its power from the battery directly. There is no power regulation. Your device will take only what it needs. It won't effect the life of your battery. Think about the charger you plugged into the wall socket. A wall socket can generate enough current to melt metal. Lower power draw is cooler but really just make sure the voltage rating matches and the amp rating isn't too low. USB should be 5 volts anyways. The big issue with amperage, can the charger handle the draw? Example would be a 3000watt car amp drawing power from a 18 gauge speaker wire. It might work but the wire will heat up since it isn't designed to carry that much current.
In short for USB the charger amperage can be higher than the device needs but probably no less than 1/2 the rated amps for the device.
As above, you could plug in a 200A charger and the phone will still only draw the same current as from a 2A charger.
The amount of current drawn by the device is firmware controlled to protect the battery from heat damage.
The stock charger is 1.5A so the phone must draw no more than that.
It's all about cables too. I have a 2 amp TomTom charger hooked up to a 3 metre long USB cable but it charges slower than the standard 'in the box' charger Sony supply at 1.5 amp.
More cable and wrong core rating = more energy lost or wasted. I actually had to ask a sparky about this one, but it's true. Cable length, rating and core make all the difference.
For instance.
If you hooked up a 3 amp charger (I had one for an old phone) to a cable that can only handle 1 amp then you will only get 1 amp into the device, probably melt your cable too over time.
Honestly, the best bet is to use as near as dammit to the original rating on the included in the box charger. Electricity is a funny thing, it can screw your phone up in ways only time and noting the battery life will show.
Sent from my C6603 using xda app-developers app
so this combo is working for me:
http://www.amazon.com/gp/product/B010UT6Z3Q?psc=1&redirect=true&ref_=oh_aui_detailpage_o08_s01
http://www.amazon.com/gp/product/B00W98IQ5M?psc=1&redirect=true&ref_=oh_aui_detailpage_o08_s00
the latter also allowed me to fastboot oem unlock.
so battery is at 59%, homescreen says 14 minutes till full.
cheers
can you please check with Ampere or GSAM for the charging speeds that you achieve?
does the device say fast/rapid charging?
Interested to hear the results from Ampere or GSAM as well
i cant get a good handle on how ampere works. it keeps measuring, takes forever, and fluctuates a lot.
with the aukey combo, i got 1830/2050mA @ 4.14v, at 53%, 37.7c
took it off charge for a while and tried again with the stock charger:
with the stock charger, i got 1850/1860mA(min/max) @ 4.159Vat 61%, 30.7c
I will try again at 50% today if I have time but I am pretty pleased with my little aukey combo. It was cheap.. I got it when there was a 7 dollar coupon floating around.
FYI, believe this is the same charger : http://www.amazon.com/gp/product/B00QEX83LA/
Use Promo Code DBVITSZB to drop price to $6.99
Can only purchase 1 at the discounted price.
TCstr8 said:
FYI, believe this is the same charger : http://www.amazon.com/gp/product/B00QEX83LA/
Use Promo Code DBVITSZB to drop price to $6.99
Can only purchase 1 at the discounted price.
Click to expand...
Click to collapse
Yep that would be the one. charging at 1800mA is not the fastest that the phone can charge at though. I'm going to hold off for the ones that enable the full speed of charging
http://www.droid-life.com/2015/10/19/nexus-6p-nexus-5x-quick-charge/
For 7 bux I think it's still a good deal for someone who doesnt have a spare to use
From the product description, you are only going to get 2A out of the charger. 5X doesn't do QC2.0, so you will only get the output at 5V, which for this charger is 2 amps.
Specifications:
Input: AC 100-240V
Output: 5V/2A, 9V/2A, 12V/1.5A
Dimensions2.69*2.05*0.87in)(68.5*52*22mm)
zackhow said:
From the product description, you are only going to get 2A out of the charger. 5X doesn't do QC2.0, so you will only get the output at 5V, which for this charger is 2 amps.
Specifications:
Input: AC 100-240V
Output: 5V/2A, 9V/2A, 12V/1.5A
Dimensions2.69*2.05*0.87in)(68.5*52*22mm)
Click to expand...
Click to collapse
But some Aukey chargers with AIPowertech like this one "charges all non-Quick ChargeTM 2.0 phones and tablets at their normal speed (up to 5 volts / 2.4A Max)with AIPower Tech Technology."
I've got the charger, just not the cables... so haven't been able to test.
I tested Aukey PA-T2 wall charger QC2.0 port ( orange one) on a Sony Xperia Z3 compact tablet
I recorded charging current up to 2.7Amp with the Aukey USB cable and up to 3.0 Amp with the Sony USB cable !!!! far more than the 2.0 Amp level current Aukey specifies......
The voltage - current output test show that the voltage stay in the 9.0V range with current up to 2.4Amp then fall down very quickly. It seems that the voltage stay at a value enough to deliver up to 3.0 Amp charging current to the tablet ....
Detailed test are here (http://78michel.unblog.fr/?p=860 in french....)
Current values where obtained from BMW recordings
Using the
Aukey Quick Charge 2.0 18W USB Turbo Wall Charger
And
http://www.amazon.com/dp/B01706YAXY
Getting Charging Rapidly. The juice isn't nearly as good as the stock charger, but this is the first combo with a USB-A to USB-C cable that I've gotten the Charging Rapidly notification.
7_michel said:
I tested Aukey PA-T2 wall charger QC2.0 port ( orange one) on a Sony Xperia Z3 compact tablet
I recorded charging current up to 2.7Amp with the Aukey USB cable and up to 3.0 Amp with the Sony USB cable !!!! far more than the 2.0 Amp level current Aukey specifies......
The voltage - current output test show that the voltage stay in the 9.0V range with current up to 2.4Amp then fall down very quickly. It seems that the voltage stay at a value enough to deliver up to 3.0 Amp charging current to the tablet ....
Detailed test are here (http://78michel.unblog.fr/?p=860 in french....)
Current values where obtained from BMW recordings
Click to expand...
Click to collapse
LOL, thanks... but that doesn't really help this 5X cause. Given that there is no quick charge on the 5X, it'll remain at 5V. The question is whether it'll pull more than the 2A or 2.4A specified on these chargers at 5V on a 5X.
PatcheZ said:
LOL, thanks... but that doesn't really help this 5X cause. Given that there is no quick charge on the 5X, it'll remain at 5V. The question is whether it'll pull more than the 2A or 2.4A specified on these chargers at 5V on a 5X.
Click to expand...
Click to collapse
Aukey quick charge 2.0 behave like a standard charger when connected to a non QC2.0 compatible device. The output voltage will stay to 5V so the current level will be very sensitive to the quality of the USB cable and limited by the maximum current the device will afford.
In practice it is very difficult to reach 2A charging level ( even if the charger is able to deliver such current) with a voltage output of only 5V , due to losses in cables and connectors
From my experience the higher current charging level I obtained was with a Samsung wall charger refence EP-TA10EWE which deliver an output voltage of up to 5.5V at 1.9A ( nominal voltage is claimed at 5.3V)
I got 1.7Amp charging current on my Nexus 5 while with the Aukey QC2.0 the current was only 1.1 Amp in exactly same conditions ( these recorded data are also reported in my blog .....in French.....)
7_michel said:
Aukey quick charge 2.0 behave like a standard charger when connected to a non QC2.0 compatible device. The output voltage will stay to 5V so the current level will be very sensitive to the quality of the USB cable and limited by the maximum current the device will afford.
In practice it is very difficult to reach 2A charging level ( even if the charger is able to deliver such current) with a voltage output of only 5V , due to losses in cables and connectors
From my experience the higher current charging level I obtained was with a Samsung wall charger refence EP-TA10EWE which deliver an output voltage of up to 5.5V at 1.9A ( nominal voltage is claimed at 5.3V)
I got 1.7Amp charging current on my Nexus 5 while with the Aukey QC2.0 the current was only 1.1 Amp in exactly same conditions ( these recorded data are also reported in my blog .....in French.....)
Click to expand...
Click to collapse
Thanks, didn't think to look at the link.
I wonder how older phones like the NA Galaxy S3 and Nexus 4 that both have QC1.0 ([email protected]) compare to the charging of the Nexus 5.
I'm curious as to how you did your testing, as I'm going to try my own testing once my cables come in. Did you drain all your phone's battery to 0 before performing each test? Phone airplane mode vs off? I also think that all tests must be done in relation to time, especially since the charging profile changes as the phone charges. I'm also curious as to how the non QC port on the Aukey performs, since it's spec'd at 2.4A @ 5V.
PatcheZ said:
Thanks, didn't think to look at the link.
I wonder how older phones like the NA Galaxy S3 and Nexus 4 that both have QC1.0 ([email protected]) compare to the charging of the Nexus 5.
I'm curious as to how you did your testing, as I'm going to try my own testing once my cables come in. Did you drain all your phone's battery to 0 before performing each test? Phone airplane mode vs off? I also think that all tests must be done in relation to time, especially since the charging profile changes as the phone charges. I'm also curious as to how the non QC port on the Aukey performs, since it's spec'd at 2.4A @ 5V.
Click to expand...
Click to collapse
All tests are made with battery drained to zero before starting , and a complete charge is done in each conditions. That way I can check that the full charging time is logically related to the recorded current values. The current is recorded during the complete cycle at a frequency of one value per mn.
The air plane mode was off.
Aukey QC port and non QC port are slighly differents when connected to non QC2.0 devices :
QC port delivers 5.1V in open circuit, the voltage encrease to 5.2V at 2.2Amp, on the contrary the non QC port delivers 5.2V in open circuit and decrease to 5.1V at 2.2Amp. I did not test them at higher current level.
I did not tested Galxy S3 or Nexus4 , but I beleive that a charger like the Samsung EP-TA10EWE will deliver them the maximum charging current they are programmed to accept, as obeserved for the Nexus 5.
I got the same charging current curve I recorded with Nexus 5 and Samsung EP-TA10EWE, with other set of charger and cable. This means that this charging curve is defined by the Nexus 5 inner program , not the charger characteristics. The problem is that we never know which is the max current curve internally programmed for each smartphone...... so it could be a long way to find it.......
[Review] Tronsmart QC 2.0 Dual & Quad Port Car chargers, 3 Port QC 2.0 Wall Charger
Tronsmart Quick Charge 2.0 Product Reviews
Disclaimer: I was sent these items in exchange for an unbiased review.
I will update this OP with any changes, issues, or other information as it comes up.
Tronsmart 3 Port 42W Quick Charge 2.0 Wall Travel Charger
Overview
I have accumulated a lot of devices that for better or worse need to be charged during the day sometimes all at once. For this reason, I usually carry a small battery pack or multi-port wall charger, along with some cables, adapters, and various other things. Tronsmart made a nice compact wall charger that is ideal for people who travel or on the go. I usually have a mullti-port charger or two at home (Tronsmart Titan 90W 5 port hub on my desk), and another multi-port hub on my nightstand. I always need more ports for one reason or another hence why I like having the most compact, powerful chargers that I can.
What’s in the box
-Tri-port charger
-Documentation
-Micro USB cable
Build & Design
Tronsmart makes one of my favorite looking chargers out there. The edges have a glossy finish to them that leads you into matte colored body. On one side you will see Tronsmart’s logo along with a small LED light that will light up to indicate when you’re charging. If you look at the opposite side the rated inputs/outputs for each port are specified along with a label for which ports have VoltIQ, and QC 2.0. One of the best features of this charger besides its 3 ports is the folding plug which makes it ideal for traveling/on the go.
Charging
The Quick Charge 2.0 port will allow you to charge any compatible QC 2.0 enabled device at a range of voltages/rates depending on how low the battery is. I was able to charge my S7 Edge at 9V/1.67A just like the stock Samsung Adaptive Fast Charger does. Since the S7 Edge is only rated for 9V/1.67A (15.03W) it won’t charge at a faster rate than that no matter how powerful the charger. The other two ports use VoltIQ which is another way of saying it will tell the device to charge at it’s maximum 5V rate up to 2.4A. I tested this with my S7 Edge and was able to get ~5V/1.7A which is the same output as the factory charger at the battery level I tested. Since this charger is rated for 42W which means each port can output its maximum rate simultaneously for maximum charging efficiency with multiple devices.
Charging breakdown by port
QC 2.0: 5V/2A, 9V/2A, 12V/1.5A
2x Standard Port (with VoltIQ): 5V/2.4A each
Summary
This is yet another great charger from Tronsmart (I have a lot of others that were reviewed as well) that has a nice overall design. This charger has a lot to offer in a small package coupled with a solid build that should last for a long time.
Tronsmart 4 Port Quick Charge 2.0 54W Car Charger
Overview
There is always a time that I need to charge things as I mentioned above when outlets are limited. I have a dash camera in my car that occupies one of my power outlets, so I only have 1 other easily accessible place to plug in a charger. When I go on road trips it’s nice to be able to charge my phone as well as my wife’s along with a tablet or two thanks to the wide array of ports offered with this charger.
What’s in the box
-Tronsmart Quad Port 54W Car Charger
- 3.3[ft] micro USB cable
-Documentation
Build & Design
The charger is made from plastic, but it has a nice texture to it just like the tri-port wall charger. I’ve owned and used another Tronsmart car charger (Type-C/Type-A) since December without any issues. It has really come in handy over the past couple of months thanks to its versatility, just like this one will. While this charger is quite large it packs a punch with its 4 ports while still compact for what it offers. It’s not easy to fit a large number of ports in a charger that has to fit in a confined area, but I like the overall way Tronsmart designed this one. I had no issues fitting the charger in my car, and using all of the ports, but that depends on where your outlet is located.
Charging
I tested each of the ports simultaneously with 3 of my phones, and a battery pack to ensure the charger worked as intended. I had no issues charging all 4 devices from the charger making this ideal for anyone that needs to make use of their car charger.
Charging breakdown by port:
Ports 1,2,3: 5V/2.4A (Max)
Port 4 (QC 2.0) Quick charge 5V/2A, 9V/2A , 12V/1.5A (Max)
Summary
This large 4 port charger might not be for everyone, but if you need to power a large amount of devices simultaneously than it’s an ideal choice due to its large power output.
Tronsmart 36W Dual Port Quick Charge 2.0 Car Charger
Overview
This charger is a much more compact, but still versatile dual port QC 2.0 enabled (on both ports) car charger. The overall quality/materials remain the same as the previous 4 port car charger which is a good thing. I switched from my Type-C/Type-A 33W car charger to this one in order to see how it works, and because I can still charge both my S7 Edge and Nexus 6P from it. So far over the past couple days of using this one I haven’t encountered any issues, but I will update the OP if I do.
What’s in the box
-Tronsmart Dual Port 36W Car Charger
- 2x 3.3[ft] 20AWG micro USB cables
-Documentation
Build & Design
The ports are colored (green or blue usually indicate QC 2.0 on Tronsmart chargers) while the back ports are the standard VoltIQ. For this particular one, both ports are green which is indicative of a QC 2.0 charger. There is ample spacing between both ports to accommodate any size cable that I have including: Tronsmart, Choetech, Aukey, Samsung, Google, i-Orange, Asus, Anker and many others. I haven’t found a set of cables that won’t work side-by-side in this charger. Unlike other chargers, this one doesn’t sit flush with the outlet which to me is a good thing. I always find it hard to remove the chargers that don’t protrude slightly, so I appreciate that part of the design.
Charging
Each port is capable of a 18W output which is the maximum you will ever need on a QC 2.0 enabled device. The S7 Edge can only take 15.03W (9V/1.67A), so this charger will fast charge it at the same rate as the Samsung Adaptive Fast Charger. I tested both ports with my multi-meter to ensure they lived up to their ratings.
Charging breakdown by port:
5V/2A, 9V/2A , 12V/1.5A
Summary
I have no issues with the overall design or build of this car charger, plus with the added versatility of a second QC 2.0 port it has a lot to offer. Not all chargers offer their full power output while charging multiple devices, but thankfully this one does. I don’t see any reason not to recommend it because it’s been great.
Tronsmart Micro USB Cable 6 Pack (20AWG)
Overview
I always need more cables because for some reason I either misplace them, or forget to bring them with me. I like how Tronsmart offers a large pack of cables (6 in this set) in varying sizes depending on what you might need. I usually keep the shortest one (1[ft]) in my backpack to go along with an external battery pack I carry with me. The longer ones usually find their way onto my desk or night stand because it’s nice to have the extra length so I can keep all of my devices separate & not clustered together while charging.
What’s in the box
-1[ft] micro USB cable
-2x 3.3[ft] micro USB cables
-3x 6[ft] micro USB cables
Build & Design
These cables have a larger gauge wire (20AWG) which should decrease the resistance thus allowing for less current drop in the longer variants. The connectors work well with any of my 10+ S7E cases, and they are slightly smaller physically than the Samsung one. You won’t have any issues bending these like some higher gauge cables which makes wrapping them up for storage easy.
Charging
I tested each cable length via my multi-meter to see if there was any current/voltage drop while charging my phone. I did not see any measurable drop even for the longer 6[ft] cable, so you should be able to fast charge your phone with any of them without sacrificing cable length.
Summary
I’ve actually owned a pack of these for a while now before receiving this set, and I’ve enjoyed using them. I haven’t had any of them break, fail, or otherwise suffer from flaws during my 5 months using the previous set. I enjoy the large variety of sizes offered because it allows you use a cable that suits your needs rather than one that’s too long/short.
Nice chargers. Quick chargers are very convenient. But where are the product links?
jisddwqs said:
Nice chargers. Quick chargers are very convenient. But where are the product links?
Click to expand...
Click to collapse
They were omitted because XDA likes to close OP's and mark them as spam if you include the product links as I've found out.
Sent from my Nexus 6P using XDA Labs
A comprehensive review, the chargers' design are nice, I like the round edges and corners.
Gold-plated cables seems high-end, I will search and try one of those chargers & cables.
yes it is a pity that XDA doesn't like to paste the links in the topics but what if we would google them and find them ebay or amazon and they are clones or fake.
so when connected in the car with 12V it gives 1.5A to instead of 2.4A?
Is this as good as the ones from Aukey?
Abelu said:
A comprehensive review, the chargers' design are nice, I like the round edges and corners.
Gold-plated cables seems high-end, I will search and try one of those chargers & cables.
Click to expand...
Click to collapse
The cables are all still working great; I have them in various areas to charge my numerous devices, headphones etc.
Liquid Li0n said:
yes it is a pity that XDA doesn't like to paste the links in the topics but what if we would google them and find them ebay or amazon and they are clones or fake.
so when connected in the car with 12V it gives 1.5A to instead of 2.4A?
Is this as good as the ones from Aukey?
Click to expand...
Click to collapse
It is unfortunate, and as much as I would like to post them I can't without having the OP get locked like some others I've written up. Even when I buy products and link them it raises flags for some reason, bht thags neither here nor there
The input rating if the charger is different than the output. I charged a AC 2.0 batter pack at 12V/1.5A which is the highest 12V rate that the charger is rated for. I have a Power Partners 30W single port QC 2.0 charger somewhere that will output somewhere around that in terms of the 12V but I've never tested it.
so when used in a car with 12v sigarette lighter plug it will never get higher then 1.5A or is it only this one? Are there other chargers that get more amps though that 12v port then this one?
The reason I ask is because when my phone is connected to the 12v car charger it does not get charged while using it with max brightness, gps, 4g, 2 or 3 apps at the same time, ...
Liquid Li0n said:
so when used in a car with 12v sigarette lighter plug it will never get higher then 1.5A or is it only this one? Are there other chargers that get more amps though that 12v port then this one?
The reason I ask is because when my phone is connected to the 12v car charger it does not get charged while using it with max brightness, gps, 4g, 2 or 3 apps at the same time, ...
Click to expand...
Click to collapse
As I mentioned the input current will be at 12V from the car, but it can also output at 12V via the QC standard. I can charge 2 phones (1 on each port with multimeters connected) to see he max current I can draw which should be the rated 33W if I recall correctly.
Great info you have here. lol