Database Develop

Screen lighting issue.

XDA-Dev:
I hope this finds you in high spirits and good health. Just a day ago my phone started acting peculiar regarding the lighting of the touchscreen.
Firmware: 1.6 // Build: DRC83 // Rooted: No
Damage: Slightly scratched hard plastic from dropping 2-3 times. Otherwise, outwardly pristine
Upon purchasing the phone, I immediately noticed that the screen would creak if it was pressed on the bottom right hand side (by the send button). The right side of the screen also protrudes slightly higher than the left when in the open position. I have owned the device for about 7-8 months now and have noticed that on the rear, when in open position, there is a scratch where the sliding mechanism moves. The paint is stripped and the underlying metal is displayed in those areas. And now on to the issue at hand:
When the phone is closed (touchscreen only):
- When pressing MENU, or any key that would normally illuminate the screen, this does not happen. The screen stays dim, yet the lights on the buttons bellow it brighten.
- If I slide out the keyboard while the screen is supposed to be on (meaning the buttons are lit up), nothing happens.
When the phone is open (keyboard presented):
- And the screen is off, if I press MENU, the screen comes right up with no brightness issues.
- At this point, if I close the keyboard, the backlight disables itself. The screen is NOT completely blank. If I reflect the light of the room off of it, I can just barely make out that it is indeed displaying whatever task it was that was open, but if I were in a dark room, there would be no chance of recognising what is being presented.
- Continuing from above, once the screen's backlight is disabled and I reopen the keyboard, it does not turn back on. I must turn off the screen and turn it back on for the backlight to resume normal functioning.
One would think that if the issue lies in a loose wire that once the keyboard is extended that the backlight would regain normal functioning. Because this is not happening and that it is only working under certain circumstances, I cannot accurately ascertain whether this is a software or hardware problem.
Attempted remedies:
- Soft reset (both rebooting the phone by powering off and on and by going into the reset menu)
- Hard reset (by going into the reset menu and hitting ALT+W, etc)
Neither of these attempts succeeded in restoring functionality of the backlight. I've also search high and low through the settings, but see nothing other than 'Brightness' under 'Sound & Display.'
It may be noteworthy that I have the paid application 'Power Manager' installed. Though, perhaps not since this issue was still occurring AFTER the factory reset when no foreign applications were installed.
If you require any additional details, feel free to give a reply with any questions. I'm sincerely hoping I don't have to deal with T-Mobile or HTC to have this repaired. Any tips, ideas or possible solutions would be greatly appreciated!
Regards,
Ian

Update on issue:
On the way home from work, as the battery was on it's last leg (less than 10%), I turned off the screen while the device was in the open position after finishing a text. Upon attempting to re-activate the screen, it would not do so. As always, the side buttons lit up, but the screen was blank no matter what I did. I could hear the vibration from receiving texts and the red 'omg I\'m dying LED' was still flashing, so the device had not died.
Returning home, I gave it a reboot by removing and replacing the battery. I've kept it in the open position since it has been plugged in and am quite afraid of manipulating the slide mechanism any further.
I'll be calling t-mobile to get their opinion on any further troubleshooting momentarily and report back.

Sorry for opening an older thread. do you remember what t-mobile said was the problem? i am having the same issue.

simplewhite said:
Sorry for opening an older thread. do you remember what t-mobile said was the problem? i am having the same issue.
Click to expand...
Click to collapse
The ribbon wire in the slide mechanism is either broken or pulled out of socket.

[Q] My screen taps/touches/clicks itself

as the title says i was reading when the menu started showing and hiding again and again i tought was some book issues but when i got to the homescreen it began to run apps i had on it, i have no idea of the cause of this problem

I've had this same problem. I believe it's just the software and not a deficient screen. If you look over on the nookdevs website, there's a page about recalibrating the screen. I've tried it a couple of times and it's definitely improved it. Every now and then something wacky happens, but I guess that's to be expected when you let B&N develop for Android.

I had this happen myself once, and it was pretty annoying... If I didn't have adb available I don't think I could have fixed it until I did. I wasn't able to tap the screen myself, it was taping all over the place.
I did manage after a few minutes to get multitouch paint installed and it was drawing weird dots, lines, angles, etc...
I now have the recalibrate command in gscript but not sure I could run it while it's acting up. Luckily it's only happened once, and it happened while plugged in but never seen it happen again.

Happens a lot on my NC, and I think every time its because my kids touch it with dirty fingers (sweets, chocolate etc), smearing small amounts of dirt on the screen.
The screen goes nuts within few seconds, thinks its being clicked etc...
Wiping/cleaning the screen helps to resore normal behavior, btw - while the screen is moist it does not work for me at all...
Ordered screen protectors, lets see if it makes a differencel

My screen randomly goes nuts as well. It seems like a sudden, rather than a gradual thing. The screen sometimes gets pretty dirty, but cleaning it didn't seem to make much difference. Odd thing is, what DID make a difference was taking it out of the aftermarket case. I have no idea why this would work, but it does. One thing this case does is that it pushes the power and volume buttons in, as it uses four elastic straps at the corners. Maybe holding these buttons a certain way recalibrates the screen, and if you're touching it at the time, it freaks out?

I've noticed my screen only bugs out when I have it plugged into the charger.
As long as its unplugged, its fine. As soon as i pop in the cord, the screen goes haywire.
Only the wall charger though, not when its plugged into the USB on the computer.

My screen was doing that until I got a screen protector.
Sent from my LogicPD Zoom2 using XDA App

Also, if you lock and unlock the NC it should stop acting funny.

I noticed that too. Mine hasn't gone REALLY nuts since I took it out of it's case, but sometimes when playing angry birds, it freaks out to the point where I can't play. Hitting the power button, and then hitting it again, and unlocking makes it normal. Wouldn't that indicate it's software instead of hardware? Maybe there's more than one problem?

RChadwick said:
I noticed that too. Mine hasn't gone REALLY nuts since I took it out of it's case, but sometimes when playing angry birds, it freaks out to the point where I can't play. Hitting the power button, and then hitting it again, and unlocking makes it normal. Wouldn't that indicate it's software instead of hardware? Maybe there's more than one problem?
Click to expand...
Click to collapse
Mine does the same thing every now and again. And like you, locking the screen and waking it back up fixes it every time. It's definitely software related.

Do your cases have a latch? With a magnet? Because I'm starting to think that may have something to do with it.

My case has a latch, but the magnet is not against the nook when I'm using it..

HotShotAzn said:
Do your cases have a latch? With a magnet? Because I'm starting to think that may have something to do with it.
Click to expand...
Click to collapse
Heh, I've considered that.. Also considered the mystery sensor to the left of the Nook button too.. Nook is afraid of the dark.
Seriously though, with the CPU guvna' set to ondemand and wifi turned OFF before I power it off I haven't seen it reboot yet. It rebooted once yesterday and I know it had wifi left on as I had just been using it and didn't turn it off before it went to sleep.
So totally making up numbers here....
Default CPU governor + wifi on = 30% chance it's gonna reboot when it goes to sleep..
ondemand governor + wifi on = 20% chance it's gonna reboot
ondemand govenor + wifi off = <10% chance it's gonna reboot (not gonna even say 0 here.. heh)

RChadwick said:
My case has a latch, but the magnet is not against the nook when I'm using it..
Click to expand...
Click to collapse
I tested this theory. When the Nook is in the case, I get crazy screen taps when i try to type something. Out of the case, its perfectly fine.
When I just rest the Nook on the open case (not inside the straps/holders), it will also get crazy screen taps.
One thing to note is I also did not have any problems before updating to 1.0.1. Not saying the update is the cause of the problem but its one of the variables.

Screen not working

Hello,
I have sent my gnexus off to be repaired this week and recently started to use my old milestone until my other phone is repaired. Phone was working fine, a little slow to my nexus but it was better than nothing. I was checking my emails and stuck my phone in my pocket to cross the street, when I pulled it out again, the screen would light up (glow) but the screen was black, I tried pulling the battery and rebooting but to no avail. I can feel the phone vibrate when I slide my finger across to unlock it and tap icons, but nothing is being displayed. I'm wondering if anybody else has had something like this happen and if it is possible to fix relatively easily?

If you don't get anything on the screen anymore I'm afraid it's a hardware failure.
Maybe the connector cable is broken (partially), I guess...

I guess Eiertschik is right.
In the boot process, does the M logo show up?

Verizon LG G2 Screen Issues... NOT the turn on then off issue

I have recently purchased this phone via swappa and haven't had any issues prior to this and that has been three weeks (other than a light leak).
The issue that is happening is the LCD will not turn on. When the phone is unlocked via knock on or power button you can move your finger over where the lock circle would be and feel the vibrations showing that it does register the touch. Then usually I would just hold the power button till it rebooted and this would sometimes fix the problem, on a side note the boot LG logo and boot animation do not show up during this time simply the lock screen would randomly appear.
That is problem, now on to what I tried to fix it. I have put on an entirely different rom and the problem persists, I have also flashed a different kernel on the stock rom with no avail. I at first thought it could be due to a faulty proximity sensor, but the last time the screen was on I checked it with sensor box. One way I have been able to reproduce the problem is after locking it putting it in my pocket and waiting around five minutes, this then will make it so the LCD does not turn on ( Which makes it seem like it has something to do with deep sleep). Also something I just found since I was actually able to find the power off button, the screen also won't turn on when the phone is off and plugged into the charger (this makes it seem like hardware issue). It seems like as long as I keep the phone from going to deep sleep the LCD will turn back on.
Some of this makes it seem like a software issue other things make it seem like a hardware issue. I just was wondering if anyone had any ideas or if I need to buy a new screen, if the mobo is bad, or if I could fix this with software. Any and all ideas are welcome.
Thank you all in advance.

Weirdest black screen issue, tried everything ....

Non rooted, T mobile branded 3 month old note 8. No water damange, no drops etc.
Using chrome one miniute, set the phone down to watch a movie on my tablet, picked up the phone to check messages and boom. Screen is off. The phone works, I can even answer calls because I know where the answer button is on the screen, haptic feedback works, all indicator lights work. The phone screen remains off.
Tried a soft reset (tried hard reset too the best I could being I cant see the screen) and the phone seems to reset based on the vibration and indicator light patters but the screen remains off. It's as if a physical connection between the screen and the brains of the phone has been severed. Literaraly the weirdest thing that has happened to me in a decade of Android phone ownership.
Googled all the black screen issues with these phones and most of them are resolved with just a soft reset... some said that the phone is in it's lowest dimmed state and go to a dark room and i'll see it faintly and then can increase brightness... no luck...
Has anyone experienced this?

I would say it's a warranty job, just tried turning my brightness to zero and you can still see the screen.
I did have a similar problem on an old note that had root and custom rom though but I had somehow set the volume rocker to control brightness and it had lowered itself to minimum in my pocket

KEVIN88GT said:
Non rooted, T mobile branded 3 month old note 8. No water damange, no drops etc.
Using chrome one miniute, set the phone down to watch a movie on my tablet, picked up the phone to check messages and boom. Screen is off. The phone works, I can even answer calls because I know where the answer button is on the screen, haptic feedback works, all indicator lights work. The phone screen remains off.
Tried a soft reset (tried hard reset too the best I could being I cant see the screen) and the phone seems to reset based on the vibration and indicator light patters but the screen remains off. It's as if a physical connection between the screen and the brains of the phone has been severed. Literaraly the weirdest thing that has happened to me in a decade of Android phone ownership.
Googled all the black screen issues with these phones and most of them are resolved with just a soft reset... some said that the phone is in it's lowest dimmed state and go to a dark room and i'll see it faintly and then can increase brightness... no luck...
Has anyone experienced this?
Click to expand...
Click to collapse
Try pressing and holding Volume down and power button for 5 to 7 seconds to force power off, then try to boot to download mode Volume Down + Bixby + Power button and see if the download mode screen shows......if not then probably a bad screen.
Sent from my God Mode 8

Tried it......nothing.....warranty job it is.... Bummed to have some refurnished phone in exchange for a Brand new 900 dollar phone just a few months back?

KEVIN88GT said:
Tried it......nothing.....warranty job it is.... Bummed to have some refurnished phone in exchange for a Brand new 900 dollar phone just a few months back?
Click to expand...
Click to collapse
Yeah that sucks, i can imagine..... i too hate the idea of refurbished units being swapped for warranty....bs, should be brand new unit!
Sent from my God Mode 8

so I had it replaced under warranty through T mobile. Refurb phone will come in today. One quesion. Should I let the Tmobile techs do the data/settings transfer from old phone to new one or just do everything myself from scratch (which will obviously take longer).

This happened to my phone twice for the past month or so. (both in Nougat and Oreo - Non rooted) Black screen but phone seems to be responding -- I can receive calls and notifications etc -- And force reboot doesn't fix it. I've also tried drainging the phone when it first happened to me but doesn't work. HOWEVER, it gets okay so randomly. Like I just left it for couple of hours and it just worked when I hit the power button.
I did tried bringing the device to Samsung but what they did is to just manually upgrade/reset the software in their end which I could have done in my part but I just let them do it. They told me to come back if it happens again which is kinda BS.
I can conveniently say this is a Hardware issue. I will wait for it to happen again on my phone and request for a replacement. Phone is 4 months old when it first happened.

I have the same issue with blank screen but phone is working.
It started couple of weeks after i dropped my phone on the ground. There is black dot on my screen and broken glass but phone was working ok and was still pretty usable. But then it started:
Display works fine but when i switch display of, lock the phone or display switched because of its timer it didn come switch on... But phone works, i can use it with blank (black) screen.
I had to do force restart so the display will turn on with samsung logo and booting screen, and keep on till another switch of.
I was trying every setting (but no hard reset) and then i found a little hack:
When you turn on the "Always On Display" (AOD) function you can let the screen switch off or do it manually, wait for 1-2 sec and always on display will come up to the screen. Then when you press home button or lock button screen will swtich on normally. YOu can type pin and use phone witch screen working. But when you try to unlock from "AOD" with your finger or your eyes it unlock but with screen black.
So i was using it like this. everytime you need to wait second untill AOD comes up, but it was working fine.
Problem nu 2 is that now it stop working, AOD is working but when i want to switch screen on from AOD it shows black screen and phone is working on blind.
So everytime after my screen goes black or to AOD i have to unlock the phone blindly and "Force restart" it and have to keep waiting until boot, and then have to never let phone to screen of.
Its not usuable.
¨
Now what do you think? Is it hardware problem or software problem? Because screen is working but randomly. The black dot of dead pixels on the screen is getting slightly bigger in time (about 1 year) but its like 1.5cm round. Maybe this cause the problem? And why hack with AOD was working for half a year and then stoped working? There wasnt any updates right before, but i tried to install some apps (non display related) so ill try to uninstall them.
Hawe you got any idea if i can repair it on my own even if i loose the waterproofability?
Or can it be replaced for free if i have a warranty? (I dont have insurance)
Thanks for your tips guys.

Reprocrastinator said:
I have the same issue with blank screen but phone is working.
It started couple of weeks after i dropped my phone on the ground. There is black dot on my screen and broken glass but phone was working ok and was still pretty usable. But then it started:
Display works fine but when i switch display of, lock the phone or display switched because of its timer it didn come switch on... But phone works, i can use it with blank (black) screen.
I had to do force restart so the display will turn on with samsung logo and booting screen, and keep on till another switch of.
I was trying every setting (but no hard reset) and then i found a little hack:
When you turn on the "Always On Display" (AOD) function you can let the screen switch off or do it manually, wait for 1-2 sec and always on display will come up to the screen. Then when you press home button or lock button screen will swtich on normally. YOu can type pin and use phone witch screen working. But when you try to unlock from "AOD" with your finger or your eyes it unlock but with screen black.
So i was using it like this. everytime you need to wait second untill AOD comes up, but it was working fine.
Problem nu 2 is that now it stop working, AOD is working but when i want to switch screen on from AOD it shows black screen and phone is working on blind.
So everytime after my screen goes black or to AOD i have to unlock the phone blindly and "Force restart" it and have to keep waiting until boot, and then have to never let phone to screen of.
Its not usuable.
¨
Now what do you think? Is it hardware problem or software problem? Because screen is working but randomly. The black dot of dead pixels on the screen is getting slightly bigger in time (about 1 year) but its like 1.5cm round. Maybe this cause the problem? And why hack with AOD was working for half a year and then stoped working? There wasnt any updates right before, but i tried to install some apps (non display related) so ill try to uninstall them.
Hawe you got any idea if i can repair it on my own even if i loose the waterproofability?
Or can it be replaced for free if i have a warranty? (I dont have insurance)
Thanks for your tips guys.
Click to expand...
Click to collapse
If you're under warranty it will likely be a free repair, unless they find other damage. Like moisture damage.
As far as fixing it yourself, it's just about as cheap to have Samsung do it than it is to buy the parts yourself. It's $229 for Samsung to do it, and you'll maintain the water resistance rating.

same has happened to me
KEVIN88GT said:
Non rooted, T mobile branded 3 month old note 8. No water damange, no drops etc.
Using chrome one miniute, set the phone down to watch a movie on my tablet, picked up the phone to check messages and boom. Screen is off. The phone works, I can even answer calls because I know where the answer button is on the screen, haptic feedback works, all indicator lights work. The phone screen remains off.
Tried a soft reset (tried hard reset too the best I could being I cant see the screen) and the phone seems to reset based on the vibration and indicator light patters but the screen remains off. It's as if a physical connection between the screen and the brains of the phone has been severed. Literaraly the weirdest thing that has happened to me in a decade of Android phone ownership.
Googled all the black screen issues with these phones and most of them are resolved with just a soft reset... some said that the phone is in it's lowest dimmed state and go to a dark room and i'll see it faintly and then can increase brightness... no luck...
Has anyone experienced this?
Click to expand...
Click to collapse
This has just happened to my note 8 too. I was about to update it and had started it. set my phone down and picked it up and phone screen is black but can hear the haptic feedback.

I can only see the lock screen and the notifications. Everytime I try to unlock my phone I only get to see a glimpse of the notescreen and then the screen turns black. Even when I try to go to camera through the lock screen the screen goes black too. When I charge my phone it heats up so I haven't really charged it as well. Has this also happened to anyone? It seems as if the phone's sensitivity still works in all places but when I unlock it the screen just goes black.

I also have problem of freezings and always rebooting. Tried soft and hard resets/factory reset. Still same problem. This phone has hardware issue. Do not buy.

I realize this thread is quite old but I have this exact same issue now. I have managed to discover some other information by playing around with various settings which are noted below. To begin with, I was able to used the AOD hack posted above for a while but it no longer works. The only way I can get my screen to come back is with a soft reset - but as soon as the screen times out or i turn it off, it goes black, with or without AOD enable. All the on screen buttons still work as well as the haptic feedback - I just can't see anything.
Now on to what I have found:
One thing I have found is if I turn off adaptive screen brightness and crank the brightness slider to the right, when it goes black I can faintly see some of the buttons - enough that I can turn the phone off or restart it from the power menu (If I switch the default setting to night that also helps to see the buttons a bit better). Also, if I enable night mode I can also see the brightness slider faintly but when I slide it left, it just makes the screen completely black and when I slide it right, it only returns it to the very faint brightness level.
So at this point I am stuck. To summarize the issue:
1. When the screen either times out or turns off, it is still "alive" but goes black. It will not return to normal brightness.
2. Turning off adaptive brightness and cranking brightness slider to right allows you to see faint buttons after screen times out but won't return to normal brightness.
3. Enabling night mode helps to see the faint buttons, in particular the brightness slider a bit better. However the screen still cannot return to normal brightness.
4. The only way to get the screen back to full brightness (albeit temporarily until the next timeout) is to turn off the phone or reset from the power menu; or soft reset holding volume down + power simultaneously.
Hopefully someone else has figured out a way to recover this. I am on Android 9 with Samsung UI 1.0
Phone is completely stock, never rooted and completely out of warranty.