I have a problem.
I've unlocked my bootloader and i want to install lollipop rom.
I've tried several lollipop roms, but none of them worked well on me.
ROMS that i've tried :
- BlissPop -
- AICP
-CM12.1
-Temasek
Problems:
- Sometimes i'm stuck in a screen with "starting apps" message when installing rom. the one that appeared after "installing/optimize app xx per xxx, google play service" or whatever.
- Sometimes i'm able to install the rom properly, it boots up and everything works well. The problem is, once i reboot or turn off my device, when i turned it on agan, it stuck on bootanimation (not bootloop, just bootanimation over and over without kernel logo) or stuck with "starting app" message.
What i've tried:
- relock the bootloader, restore TA, unlock bootloader again
- flash all rom stated above with default kernel
- flash all rom stated above with tangerine kernel
- flash without gapps
- flash with gapps, flash with minimal gapps
- flash stockrom -> flash custom kernel-> flash any rom above
- flash stockrom -> flash doomlord kernel v13 -> BOOTLOOP WTH?!
i've done all the steps above, and NONE of that works!
the roms always end up stuck in installation with "starting app" message or stuck in bootanimation when reboot device.
i'm quite sure that i did all steps correctly when installing rom. i've been flashing since gingerbread days, but this one make me frustrated
maybe this isn't rom problem, but my phone problem, since for other person, all roms worked well
i'll be glad if anyone know the solution :fingers-crossed:
lntermezzo said:
I have a problem.
I've unlocked my bootloader and i want to install lollipop rom.
I've tried several lollipop roms, but none of them worked well on me.
ROMS that i've tried :
- BlissPop -
- AICP
-CM12.1
-Temasek
Problems:
- Sometimes i'm stuck in a screen with "starting apps" message when installing rom. the one that appeared after "installing/optimize app xx per xxx, google play service" or whatever.
- Sometimes i'm able to install the rom properly, it boots up and everything works well. The problem is, once i reboot or turn off my device, when i turned it on agan, it stuck on bootanimation (not bootloop, just bootanimation over and over without kernel logo) or stuck with "starting app" message.
What i've tried:
- relock the bootloader, restore TA, unlock bootloader again
- flash all rom stated above with default kernel
- flash all rom stated above with tangerine kernel
- flash without gapps
- flash with gapps, flash with minimal gapps
- flash stockrom -> flash custom kernel-> flash any rom above
- flash stockrom -> flash doomlord kernel v13 -> BOOTLOOP WTH?!
i've done all the steps above, and NONE of that works!
the roms always end up stuck in installation with "starting app" message or stuck in bootanimation when reboot device.
i'm quite sure that i did all steps correctly when installing rom. i've been flashing since gingerbread days, but this one make me frustrated
maybe this isn't rom problem, but my phone problem, since for other person, all roms worked well
i'll be glad if anyone know the solution :fingers-crossed:
Click to expand...
Click to collapse
Now that is how you ask for help! Precise, systematic and detailed.
Hope you find your solution my friend :good:
XenolithicYardZone said:
Now that is how you ask for help! Precise, systematic and detailed.
Hope you find your solution my friend :good:
Click to expand...
Click to collapse
i hope so
maybe some experts know the solution?
@Mrcl1450 @prangr8 @TheAvengingTITAN @Tomoms @whitemamba @flash-
sorry for mention
Well, you tried all the tricks I know. Theres only 1 left over: flash a tft file with flashtool and start all over..
halloarno said:
Well, you tried all the tricks I know. Theres only 1 left over: flash a tft file with flashtool and start all over..
Click to expand...
Click to collapse
I believe he did that too when he relocked his boot loader.
Sent from my C5303 using XDA Free mobile app
XenolithicYardZone said:
I believe he did that too when he relocked his boot loader.
Sent from my C5303 using XDA Free mobile app
Click to expand...
Click to collapse
Dont have to.... In flashtool theres just one click option to relock bootloader with further no wiping/reinstalling etc.
halloarno said:
Dont have to.... In flashtool theres just one click option to relock bootloader with further no wiping/reinstalling etc.
Click to expand...
Click to collapse
But won't you be stuck in a bootloop if you did that on a custom ROM?
XenolithicYardZone said:
But won't you be stuck in a bootloop if you did that on a custom ROM?
Click to expand...
Click to collapse
True!
Related
Hi first of all i unlocked bootloader rooted the phone than cwm recovery and then flashed with free xperia cm10.1 and now its just showing cyanogenMod circle and not starting up, also now it says i cant unlock bootloader (i know there is a fix) but i cant do that as i have no access to the phone storage etc at all, any options ideas how bring it back to life please!?
qucharski said:
Hi first of all i unlocked bootloader rooted the phone than cwm recovery and then flashed with free xperia cm10.1 and now its just showing cyanogenMod circle and not starting up, also now it says i cant unlock bootloader (i know there is a fix) but i cant do that as i have no access to the phone storage etc at all, any options ideas how bring it back to life please!?
Click to expand...
Click to collapse
What kernel did you flash, CM have their own set of kernels and using the stock kernel with CM will cause boot-loops and this may be your problem! Flash the kernel from the CM package first then reflash the ROM, or if the kernel was the problem then flashing it via flashtool will solve the problem altogether without reflashing the ROM!!
Hit THANKS if I helped!!
gire.prasad said:
What kernel did you flash, CM have their own set of kernels and using the stock kernel with CM will cause boot-loops and this may be your problem! Flash the kernel from the CM package first then reflash the ROM, or if the kernel was the problem then flashing it via flashtool will solve the problem altogether without reflashing the ROM!!
Hit THANKS if I helped!!
Click to expand...
Click to collapse
Hi I just flashed cwm recovery and then free xperia project cm10.1 but when im trying to flash in flashtool it says that there is no loader in the phone ;/
qucharski said:
Hi I just flashed cwm recovery and then free xperia project cm10.1 but when im trying to flash in flashtool it says that there is no loader in the phone ;/
Click to expand...
Click to collapse
What where you trying to flash? If it was the CM kernel, then are you sure that you have unlocked the boot-loader the right way?
gire.prasad said:
What where you trying to flash? If it was the CM kernel, then are you sure that you have unlocked the boot-loader the right way?
Click to expand...
Click to collapse
yeah I did but it was saying somewhere there is a problem that after flashing it says the bootloader is unknown or you cant unlock it I was trying the fix didn't work either...
qucharski said:
yeah I did but it was saying somewhere there is a problem that after flashing it says the bootloader is unknown or you cant unlock it I was trying the fix didn't work either...
Click to expand...
Click to collapse
Is it a drivers problem?!! Have you installed the fastboot drivers first?
No, no, no!!
You flash the CM10 kernel via fastboot. Boot loop is because you're missing the correct kernel (you still have stock kernel)
Sent from my C6603 using xda app-developers app
Hello. I did all the steps in DooMLoRD's post, but there is something wrong. The phone is freezing all the time and really slow. After this 1 message appears "System UI has stopped" and then it works better, but when i try to start a game... "(name of the game) has stopped". I ask other guys, but they dont have problens like that on this ROM.
Can you tell me why is that? Thanks in advance!
Did you wipe your phone before installing? Try to install the DooMLoRD's rooted kernel and do a wipe in Recovery. Then, install the ROM again.
lanluckez said:
Did you wipe your phone before installing? Try to install the DooMLoRD's rooted kernel and do a wipe in Recovery. Then, install the ROM again.
Click to expand...
Click to collapse
Actually first i have installed the ROM and then kernel (is like that in the instructions)
Is it posible to have that problem if i unlocked the bootloader or root the phone wrong?
ArcS-un said:
Actually first i have installed the ROM and then kernel (is like that in the instructions)
Is it posible to have that problem if i unlocked the bootloader or root the phone wrong?
Click to expand...
Click to collapse
As long as your bootloader is unlocked root is not important for flashing this ROM. And if you already managed to install custom kernel (for example for aosp based rom) then you successfully unlocked your bootloader. Maybe as the previous post said, try to install DooMLoRD's kernel (The old one) then reboot recovery, wipe, flash 4.3 zip and it should work
pec0ra said:
As long as your bootloader is unlocked root is not important for flashing this ROM. And if you already managed to install custom kernel (for example for aosp based rom) then you successfully unlocked your bootloader. Maybe as the previous post said, try to install DooMLoRD's kernel (The old one) then reboot recovery, wipe, flash 4.3 zip and it should work
Click to expand...
Click to collapse
I have installed this one: SP-4.3_leak_256-DooMLoRD_AdvStkKernel-v1 Is that the new one ?
I found this: SP-DooMKernel-v03 and SP-DooMKernel-v04
Is that the older kernels ? Because i try the kernel in the ZIP with the ROM and there is no recovery...
Guys....
Im trying to install leaked 4.3 but have issue
1.flashed .254 using flash tool
2.Rebooted
3.Flashed Advanced kernel via fastboot
4.Rebooted
but when i turn on the phone after that,it vibrates once and then there is no display.
so i flashed .254 stock kernal but that didnt fix the issue
As of now im on .254 stock ROM with bootloader locked again
Please explain me step by step process to get this done with 4.3 plzzz
Please note that my phone even though was c5302 always displayed as c5303 in PC companion but it isnt now.
sabertooth777 said:
Guys....
Im trying to install leaked 4.3 but have issue
1.flashed .254 using flash tool
2.Rebooted
3.Flashed Advanced kernel via fastboot
4.Rebooted
but when i turn on the phone after that,it vibrates once and then there is no display.
so i flashed .254 stock kernal but that didnt fix the issue
As of now im on .254 stock ROM with bootloader locked again
Please explain me step by step process to get this done with 4.3 plzzz
Please note that my phone even though was c5302 always displayed as c5303 in PC companion but it isnt now.
Click to expand...
Click to collapse
Okay! Do it this way
Unlock ur Bootloader
Flash stock .254 ftf
Then root and install cwm by locked bootloader method
( by installing previous firmware kernel ftf, root by doomloard kit, install cwm of locked bootloader then flash ur latest. 254 kernel ftf)
Now just flash the 4.3 rom through Cwm without Wiping anything
Sent from my C5303 using XDA Premium 4 mobile app
sabertooth777 said:
Guys....
Im trying to install leaked 4.3 but have issue
1.flashed .254 using flash tool
2.Rebooted
3.Flashed Advanced kernel via fastboot
4.Rebooted
but when i turn on the phone after that,it vibrates once and then there is no display.
so i flashed .254 stock kernal but that didnt fix the issue
As of now im on .254 stock ROM with bootloader locked again
Please explain me step by step process to get this done with 4.3 plzzz
Please note that my phone even though was c5302 always displayed as c5303 in PC companion but it isnt now.
Click to expand...
Click to collapse
Of course, cause u havent flashed the rom yet! You only flash the kernel, not the rom.
Now do it exactly as you did before, but after flashing the kernel and rebooting, tap the volume uo button continuously until you boot into cwm. And then you can flash the rom through cwm.
Dont forget to copy the zip in your ext sdcard before flashing the kernel!
Cheers.
I don't have the Take Screenshot option in the power menu. Is that normal ? Is it disabled by default or something ?
ArcS-un said:
Hello. I did all the steps in DooMLoRD's post, but there is something wrong. The phone is freezing all the time and really slow. After this 1 message appears "System UI has stopped" and then it works better, but when i try to start a game... "(name of the game) has stopped". I ask other guys, but they dont have problens like that on this ROM.
Can you tell me why is that? Thanks in advance!
Click to expand...
Click to collapse
Read. You clearly haven't read the thread by Doomlord, you should. "WHY WONT IT READDDDD"
Robin>Hood said:
Read. You clearly haven't read the thread by Doomlord, you should. "WHY WONT IT READDDDD"
Click to expand...
Click to collapse
Did you notice that this is my POST with my PROBLEM ?
marsx1984 said:
I don't have the Take Screenshot option in the power menu. Is that normal ? Is it disabled by default or something ?
Click to expand...
Click to collapse
YES its normal
even i dont have it
for taking screenshot press vol down and power button together
As the title suggests, I rooted my phone, unlocked BL and was about to flash CM for Honami, which is Z1, but the flashing of the ROM was stopped because it recognizes my device, a Z1, as a "togari", a Z Ultra. I find this quite odd as I have practically no idea why it does that.
I also tried flashing "togari" CM ROM, but that also fails.
Any fixes for this?
Sari95 said:
As the title suggests, I rooted my phone, unlocked BL and was about to flash CM for Honami, which is Z1, but the flashing of the ROM was stopped because it recognizes my device, a Z1, as a "togari", a Z Ultra. I find this quite odd as I have practically no idea why it does that.
I also tried flashing "togari" CM ROM, but that also fails.
Any fixes for this?
Click to expand...
Click to collapse
if you are sure that you have an z1... then just remove the device check in the updater script (within the zip...) it is in the beginning... cant really remember how it looks but ... search google perhaps.. then it will flash weird enough ... my s also identifies as an sl... but that is from the build prop
HellRoot said:
if you are sure that you have an z1... then just remove the device check in the updater script (within the zip...) it is in the beginning... cant really remember how it looks but ... search google perhaps.. then it will flash weird enough ... my s also identifies as an sl... but that is from the build prop
Click to expand...
Click to collapse
Haha, yes. I google for it and tried to simply delete the device check in update-script, but it didn't work for me. I believe the issue is in my recovery, which is not a 4.4 kitkat recovery. The CWM-recovery I have at the moment is 6.0.3.6 and I believe that is the reason for my issues. I have had no luck trying to find a 4.4 kitkat recovery... any tips here?
Sari95 said:
Haha, yes. I google for it and tried to simply delete the device check in update-script, but it didn't work for me. I believe the issue is in my recovery, which is not a 4.4 kitkat recovery. The CWM-recovery I have at the moment is 6.0.3.6 and I believe that is the reason for my issues. I have had no luck trying to find a 4.4 kitkat recovery... any tips here?
Click to expand...
Click to collapse
well..i have never had problems with it being the recovery... what error does it make now?
HellRoot said:
well..i have never had problems with it being the recovery... what error does it make now?
Click to expand...
Click to collapse
I tried this recovery too, without any luck: http://forum.xda-developers.com/showthread.php?p=49966299
To begin with I got Status 7 error, which is now gone.. I found a tutorial to flash SlimRom for Z1, which is android 4.4.2: http://www.ibtimes.co.uk/android-4-4-2-kitkat-sony-xperia-z1-available-via-slimkat-rom-1432702
However, I was only able to make emergency calls, no cellular at all. I flashed CM through the same method and everything I tried worked, except cellular. Thus, I had to wipe it and install stock Sony firmware.
After that I tried flashing CM the "normal" way through recovery and everything installed as usual, but when I push reboot to reboot the system, the phone simply shuts off. Even if I press the powerbutton to turn it on, it only vibrates and nothing else happens. Again, I flashed stock firmware to be able to use the phone again...
I am very confused about this, because it does not give any errors. It simply does not work :l
[/COLOR]
Sari95 said:
I tried this recovery too, without any luck: http://forum.xda-developers.com/showthread.php?p=49966299
To begin with I got Status 7 error, which is now gone.. I found a tutorial to flash SlimRom for Z1, which is android 4.4.2: http://www.ibtimes.co.uk/android-4-4-2-kitkat-sony-xperia-z1-available-via-slimkat-rom-1432702
However, I was only able to make emergency calls, no cellular at all. I flashed CM through the same method and everything I tried worked, except cellular. Thus, I had to wipe it and install stock Sony firmware.
After that I tried flashing CM the "normal" way through recovery and everything installed as usual, but when I push reboot to reboot the system, the phone simply shuts off. Even if I press the powerbutton to turn it on, it only vibrates and nothing else happens. Again, I flashed stock firmware to be able to use the phone again...
I am very confused about this, because it does not give any errors. It simply does not work :l
Click to expand...
Click to collapse
just copied from the CM11 dev fora...
Install instructions:
first time
- power off the phone:
- hold vol+ and plug usb to boot into fastboot (blu led)
- fastboot flash boot boot.img (from cm10 zip)
- fastboot reboot
- enter recovery, on boot led will be violet for 3'', during this period press vol+
- flash rom zip
- flash gapps zip
- wipe
- reboot
for update just flash rom zip from recovery
Google Apps are not included in this ROM. You'll need to find those yourself if you want them.
HellRoot said:
[/COLOR]
just copied from the CM11 dev fora...
Install instructions:
first time
- power off the phone:
- hold vol+ and plug usb to boot into fastboot (blu led)
- fastboot flash boot boot.img (from cm10 zip)
- fastboot reboot
- enter recovery, on boot led will be violet for 3'', during this period press vol+
- flash rom zip
- flash gapps zip
- wipe
- reboot
for update just flash rom zip from recovery
Google Apps are not included in this ROM. You'll need to find those yourself if you want them.
Click to expand...
Click to collapse
Hmm... seems reasonable. Could you give me the link to the fora, so I can try this method out too ?
Sari95 said:
Hmm... seems reasonable. Could you give me the link to the fora, so I can try this method out too ?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2540650
there it is.... hope you figure it out.
Sari95 said:
As the title suggests, I rooted my phone, unlocked BL and was about to flash CM for Honami, which is Z1, but the flashing of the ROM was stopped because it recognizes my device, a Z1, as a "togari", a Z Ultra. I find this quite odd as I have practically no idea why it does that.
I also tried flashing "togari" CM ROM, but that also fails.
Any fixes for this?
Click to expand...
Click to collapse
I had this problem when I try to flash with LB.
HellRoot said:
http://forum.xda-developers.com/showthread.php?t=2540650
there it is.... hope you figure it out.
Click to expand...
Click to collapse
Thank you I kind of figured it out... but I am not sure why/ how xD I wiped everything, flashed stock firmware "a.136", rooted, installed recovery and flashed CM. After that, it worked as it is supposed to, so problem solved
Thanks for your help
Sari95 said:
Thank you I kind of figured it out... but I am not sure why/ how xD I wiped everything, flashed stock firmware "a.136", rooted, installed recovery and flashed CM. After that, it worked as it is supposed to, so problem solved
Thanks for your help
Click to expand...
Click to collapse
good to hear hope you enjoy the CM.... if you want then please tell me how it is running.. performance, battery, camera etc
have a good day
Hi Guys,
I have s3 GT-I9305, android version 4.1.2, baseband version I9305XXBLL5. Australian model for Optus.
I successfully rooted and installed Philz_Touch_6.19.3 _ After that I could do Nandroid online backup and confirm it is rooted.
When I tried to flash custom ROM today - I found I can't boot in CWM/Philz recovery mode. Then I tried to different version of Philz/CWM and TWRP but none worked. It keeps booting in stock recovery mode- I get message as shown in attached image.
PS: I have USB diagnosis checked but haven't unlocked boot loader?
to be specific: my phone works fine - boots fine - It is just I want to load custom rom and it won't go to custom recovery and I can't load custom ROM.
Thanks.
HELP!
can anyone please help me out here!
I kept searching and found some solution but none worked.
I used triangle away. - didn't work
Installed custom recovery without checking auto reset and started after pulling battery out. - didn't work
It still boot in odin mode and I can't go to custom recovery
i have the same problem too when i got my phone flashed 3rd recovery last year,
the stock recovery can automaticly restore itself after reboot~
but i found the solution here in xda,just flash a zip to unlock the self-protection of the stock recovery~
i will tell you the link and the attachment several hours later after my work,if you cannt wait, you can search it here,maybe you can find it yourself.
Sent from my GT-I9305
Aphirodite said:
i have the same problem too when i got my phone flashed 3rd recovery last year,
the stock recovery can automaticly restore itself after reboot~
but i found the solution here in xda,just flash a zip to unlock the self-protection of the stock recovery~
i will tell you the link and the attachment several hours later after my work,if you cannt wait, you can search it here,maybe you can find it yourself.
Sent from my GT-I9305
Click to expand...
Click to collapse
I had a quick search but couldn't find it. Will greatly appreciate if you can post link.
Thanks
even after you flash a custom recovery...your phone will automatically flash stock recovery every time it reboots...so that's why you will get into stock even if you flash CWM/TWRP or what you like.....
here is the solution: http://forum.xda-developers.com/gal...-cf-root-cwm-recovery-ported-supersu-t1914394
read at the end of the first post....WORKAROUND......
i used myself and worked....
ggmm2013123 said:
I had a quick search but couldn't find it. Will greatly appreciate if you can post link.
Thanks
Click to expand...
Click to collapse
the guy offered the post which included the solution.
try to flash the "Remove-boot-recovery.p.zip",it will work..
good luck
:fingers-crossed:
Done
Thanks guys.
Above solution didn't work for me but I got it working through rom manager App. I reboot to recovery through ROM Manager and it worked.
How ever After I installed Pacman rom, I couldn't use App as there were no Gapps and wouldn't boot to recovery. The workaround here was to press home, volume up and lock button simultaneously and release it after few second and it will go to custom recovery.
In the end, I am on Pacman Nightly 06/04/2014 with Philz touch recovery.
Hi! I have an lg OB running ics 4.0.4(V30B). The phone it's rooted and I have CWM installed from Rom Manager. I can acces Recovery from Rom Manager and with the phone off ( VOLUME PLUS + G KEY). The problem is that I can't flash any Rom bellow ics (not even with Smart Flash Tools) without getting bootloops. I can flash Roms based on ics and above( IZS,CM10.1,NAMELESS ROM NIGHTLIES 4.4.4).
Could someone help me?
Nobody?
JoKeR[RO-VL] said:
Nobody?
Click to expand...
Click to collapse
I was hoping you fixed the issue. I don't know what to do.
It's a matter of unlocking the boot loader. Once you do that, you can jump back and forth between ICS-based ROMs and everything else.
Gingerbread ROMs include the boot loader (marvel and Huexxx).
androcraze said:
I was hoping you fixed the issue. I don't know what to do.
It's a matter of unlocking the boot loader. Once you do that, you can jump back and forth between ICS-based ROMs and everything else.
Gingerbread ROMs include the boot loader (marvel and Huexxx).
Click to expand...
Click to collapse
Man I can flash ICS-based ROMs .JB and KK, I can't flash GB stock or GB-based ROMs, not even with SFT.
I think the bootloader it's unlocked because I can acces CWM from switch off phone(key combo)....I am confused because i read many tutorials but they are contradictory
That happends also with me 2 times.
Just flash CWM recovery again.
ptxpaulo said:
That happends also with me 2 times.
Just flash CWM recovery again.
Click to expand...
Click to collapse
Already tried....when i try to flash a GB ROM stock or custom GB-based Rom I get stuck in a bootloop.Same story with Smart Flash Tools...SFT says "succes", I hear the "ta daaa" sound ,phone reboots but stuck in a bootloop.
JoKeR[RO-VL] said:
Already tried....when i try to flash a GB ROM stock or custom GB-based Rom I get stuck in a bootloop.Same story with Smart Flash Tools...SFT says "succes", I hear the "ta daaa" sound ,phone reboots but stuck in a bootloop.
Click to expand...
Click to collapse
Try toii install a ROM right after rebooting from flash.
What I did is: Install a JB ROM, After, I reinstall CWM with ADB, reboot and then I could install any rom.
ptxpaulo said:
Try toii install a ROM right after rebooting from flash.
What I did is: Install a JB ROM, After, I reinstall CWM with ADB, reboot and then I could install any rom.
Click to expand...
Click to collapse
Sorry but how to install CWM with ADB? I've installed CWM(6.0.1.4) only from Rom Manager....
JoKeR[RO-VL] said:
Sorry but how to install CWM with ADB? I've installed CWM(6.0.1.4) only from Rom Manager....
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1613183
ptxpaulo said:
http://forum.xda-developers.com/showthread.php?t=1613183
Click to expand...
Click to collapse
Doesn't work and its stuck on lg logo now
Try to flash first original Froyo 2.2.2 , and then you can upgrade to GB ! Worked for me !
seby24gl said:
Try to flash first original Froyo 2.2.2 , and then you can upgrade to GB ! Worked for me !
Click to expand...
Click to collapse
Did you unlocked the bootloader first? can you put a link with your froyo and SFT?
I am from Romania so I need an Europe Open
No, I don't tried to unlock bootloader, but like you , I got the bootloops every time I downgrade from ICS, Nameless or cyanogen roms . I use original Froyo - flashed with SFT , then upgrade to GB with Cwm recovery patch- flashed with SFT, then boot to recovery and install Nameless. I will give you the links, once I uploaded to my dropbox.
Here, I hope will help you : https://www.dropbox.com/s/psniks1yvqwymy9/firmware v10a-europe-p970.rar
seby24gl said:
No, I don't tried to unlock bootloader, but like you , I got the bootloops every time I downgrade from ICS, Nameless or cyanogen roms . I use original Froyo - flashed with SFT , then upgrade to GB with Cwm recovery patch- flashed with SFT, then boot to recovery and install Nameless. I will give you the links, once I uploaded to my dropbox.
Here, I hope will help you : https://www.dropbox.com/s/psniks1yvqwymy9/firmware v10a-europe-p970.rar
Click to expand...
Click to collapse
Thanks bro! Hope it works.
seby24gl said:
No, I don't tried to unlock bootloader, but like you , I got the bootloops every time I downgrade from ICS, Nameless or cyanogen roms . I use original Froyo - flashed with SFT , then upgrade to GB with Cwm recovery patch- flashed with SFT, then boot to recovery and install Nameless. I will give you the links, once I uploaded to my dropbox.
Here, I hope will help you : https://www.dropbox.com/s/psniks1yvqwymy9/firmware v10a-europe-p970.rar
Click to expand...
Click to collapse
JoKeR[RO-VL] said:
Thanks bro! Hope it works.
Click to expand...
Click to collapse
It's not working. Don't know what to try
UP! When I use the bootloader unlocker app the flashing process take about 2-3 seconds and the app closing by itself without any message like "succes". I even tried to flash a u-boot img uploaded by huexxx and at the second reboot the phone stucks on lg logo without flashing leds
JoKeR[RO-VL] said:
UP! When I use the bootloader unlocker app the flashing process take about 2-3 seconds and the app closing by itself without any message like "succes". I even tried to flash a u-boot img uploaded by huexxx and at the second reboot the phone stucks on lg logo without flashing leds
Click to expand...
Click to collapse
Did you already try the alternative way without the app? Which means load the files to your sdcard and afterwards type the dd if=xxxx of=xxxx? This could show if it works or fails. And did you ever flash the LU5900 port? So the early ICS ROM released by Redy, Gabwerkz and me. Try the manual unlock first.
Sent from my XT1052 using XDA Free mobile app
N00BY0815 said:
Did you already try the alternative way without the app? Which means load the files to your sdcard and afterwards type the dd if=xxxx of=xxxx? This could show if it works or fails. And did you ever flash the LU5900 port? So the early ICS ROM released by Redy, Gabwerkz and me. Try the manual unlock first.
Sent from my XT1052 using XDA Free mobile app
Click to expand...
Click to collapse
NO I did not flash the LU5900 port.Where do I need to type dd if ? I use windows 7 on my laptop.
JoKeR[RO-VL] said:
NO I did not flash the LU5900 port.Where do I need to type dd if ? I use windows 7 on my laptop.
Click to expand...
Click to collapse
As written in the thread, type it into terminal emulator (an app). Read the thread carefully please.
Sent from my XT1052 using XDA Free mobile app
N00BY0815 said:
As written in the thread, type it into terminal emulator (an app). Read the thread carefully please.
Sent from my XT1052 using XDA Free mobile app
Click to expand...
Click to collapse
OK I have the terminal emulator on my phone.
I've read the thread and it says "Move this two files, bootloader and recovery to the root of memory sdcard;
Enter in the command line
su
dd if=/sdcard/u-boot.img of=/dev/block/mmcblk0p2
dd if=/sdcard/recovery.img of=/dev/block/mmcblk0p4
And reboot or reboot recovery."
I have downloaded all on my laptop(bootloader recovery and su) but I am confuse....what's with that "su"?
Do I have to put it on the root of the sdcard too?
Sorry for my noob question