Related
Hello!
I'm currently stationed in Singapore and bought a Moto X about a month or so ago from eBay. While I am anxiously waiting for my Moto X to receive the 4.4 update, I realised that the system version (after the previous camera update) is 139.12.35.ghost_row.AmericaMovil.en.PR, which I found to be a Latin America version after some searching on the forums and Googling here and there.
I also found this thread, where OP said that they can be flashed over to either the T-Mobile version. Does this continue to work for the 4.4 updates by T-Mobile or AT&T, and would there be anything else required for flashing? (I saw something about flashing new radios and all, but was quite confused by contradicting explanations and suggestions :/)
Thanks in advance!
// EDIT:
To add on after a bit of searching, I realised that I am allowed to unlock my bootloader, despite claims from the original retailer on eBay that the phone came from AT&T (which is notorious, even here, for their stance on bootloader unlocking). What gives?
I got the same Moto X from a buddy yesterday. I did a lot of searching and also discovered the thread about the phone being flashed to t- mobile.
I fooled the steps on another thread titled " Return to stock 100%" out something like that...
I downloaded the correct Att firmware and with the use of RSDLite, I successfully flashed my Moto X to ATT.... it took less than 10 minutes. And as soon as it booted up, I got hit with the "update available" message ( kit Kat)
Sent from my XT1058 using Tapatalk
Thanks for the information!
I've successfully upgraded my phone to the Verizon version (minus all the bloatware that I hastily blasted off), with root and TWRP. So this is what I did, for future reference:
It seems that AmericaMovil versions are not bound by the AT&T's locked bootloader policies, and other Latin America versions are probably free from the restriction too. So I managed to get my hands on the Motorola Fastboot and unlocked my bootloader. TWRP was installed (remember to use 2.6.3.1 and above for 4.4 support), and then flashed the Verizon system dump available here. Root was installed by TWRP.
After getting on the device and setting things up, I rebooted to recovery to remove lots of bloatware (available in /system/app and /system/priv-app). Had to remove some of them through Titanium Backup as the file names were not always indicative that it came from Verizon. I made the extra step of killing the god-awful boot animation that they had by replacing it with this.
And... that concludes my experience with this, I suppose.
I've been looking through a few threads and I am not comfortable enough to flash the T-Mobile rom over my AmericanMovil one yet.
I can't seem to find step by step instructions on how to do this.. Would anyone like to explain it from the ground up?
My understanding
1) unlock bootloader
2) flash a recovery like twrp or cmw
3) flash the rom that is given in the OG post here http://forum.xda-developers.com/showthread.php?t=2477180
4) this should now give us the t-mobile version of things and we should be able to do the standard OTA from there?
[Q] So can this all be done without ever having to root the phone?
alternetconcept said:
I've been looking through a few threads and I am not comfortable enough to flash the T-Mobile rom over my AmericanMovil one yet.
I can't seem to find step by step instructions on how to do this.. Would anyone like to explain it from the ground up?
My understanding
1) unlock bootloader
2) flash a recovery like twrp or cmw
3) flash the rom that is given in the OG post here http://forum.xda-developers.com/showthread.php?t=2477180
4) this should now give us the t-mobile version of things and we should be able to do the standard OTA from there?
[Q] So can this all be done without ever having to root the phone?
Click to expand...
Click to collapse
I'm not too sure whether flashing via TWRP/CMW will allow you to get OTA, unfortunately. Which is why I went straight for the Verizon system dump. But yes, you can change firmware without ever having to root the phone. Heck, I think there's a guide on restoring mentioned by @plmiller0905 below that will allow you to do it without unlocking the bootloader, even.
RagnaParadise said:
I'm not too sure whether flashing via TWRP/CMW will allow you to get OTA, unfortunately. Which is why I went straight for the Verizon system dump. But yes, you can change firmware without ever having to root the phone. Heck, I think there's a guide on restoring mentioned by @plmiller0905 below that will allow you to do it without unlocking the bootloader, even.
Click to expand...
Click to collapse
I believe the bootloader does have to be unlocked in order to flash a different firmware.
Sent from my XT1058 using Tapatalk
RagnaParadise said:
I'm not too sure whether flashing via TWRP/CMW will allow you to get OTA, unfortunately. Which is why I went straight for the Verizon system dump. But yes, you can change firmware without ever having to root the phone. Heck, I think there's a guide on restoring mentioned by @plmiller0905 below that will allow you to do it without unlocking the bootloader, even.
Click to expand...
Click to collapse
Yeah after doing so more reading.. (at least the way I'm willing to do it) is to just unlock my bootloader and then using RSD Lite (Which i still have no idea what that is / where it is) flash an SBF found here (http://sbf.droid-developers.org/ghost_rcica/list.php)
I guess following this video somewhat http://www.youtube.com/watch?v=Fr0JHSAXJDI#t=15
Does that sound right?
Should I flash the TMO_RETAIL_XT1053_4.2.2-13.9.0Q2.X-116-X-17-57_MR1_CFC.xml.zip
Or just jump straight to the 4.4 version TMO_RETAIL_XT1053_4.4-13.11.1Q2.X-69-3_MR2_CFC.xml.zip
??
As far as I know, the use of RSD Lite doesn't require an unlocked bootloader (at least, that's what it shows in the video you showed me anyway), especially since these are images supposedly signed by Motorola themselves. Let me know if you've found something else?
As for your question on which to flash... I'm not sure, but you'd skip a lot of the hassle if you could flash 4.4 straight, so how about trying that?
RagnaParadise said:
As far as I know, the use of RSD Lite doesn't require an unlocked bootloader (at least, that's what it shows in the video you showed me anyway), especially since these are images supposedly signed by Motorola themselves. Let me know if you've found something else?
As for your question on which to flash... I'm not sure, but you'd skip a lot of the hassle if you could flash 4.4 straight, so how about trying that?
Click to expand...
Click to collapse
Rsdlite is a shell for a flash boot flash supposedly with an XML doing all the steps together. Just makes it easier.
You need unlocked boot loader only to flash an image that doesn't match your current boot loader. So if you have a. At&t phone you can only flash at&t images by rsdlite. But if you unlock your amerimovil phone you can flash any xt1058 image I think. So amerimovil could take say a rogers or at&t or telcel image. Not sure if T-Mobile image will work on a full rsdlite flash as it is an xt1053 image. I think you can flash most of a T-Mobile image by twrp but not by rsdlite not sure
sleepyguy007 said:
Rsdlite is a shell for a flash boot flash supposedly with an XML doing all the steps together. Just makes it easier.
You need unlocked boot loader only to flash an image that doesn't match your current boot loader. So if you have a. At&t phone you can only flash at&t images by rsdlite. But if you unlock your amerimovil phone you can flash any xt1058 image I think. So amerimovil could take say a rogers or at&t or telcel image. Not sure if T-Mobile image will work on a full rsdlite flash as it is an xt1053 image. I think you can flash most of a T-Mobile image by twrp but not by rsdlite not sure
Click to expand...
Click to collapse
So if I flash the at&t image found here (http://sbf.droid-developers.org/ghost_rcica/list.php), would it come pre-loaded with all the bloatware AT&T has even though I'm not using AT&T network?
alternetconcept said:
So if I flash the at&t image found here (http://sbf.droid-developers.org/ghost_rcica/list.php), would it come pre-loaded with all the bloatware AT&T has even though I'm not using AT&T network?
Click to expand...
Click to collapse
yes of course. think about it like if you took a dell windows 7 install CD , and put it on an HP. all the dell customizations would still be there.
obviously since you have unlocked bootloader, once you do the RSDlite you can always flash twrp, and superuser, and delete all that stuff. but then you wouldn't get updates again. i dont think the at&t image is really THAT bad. though i've heard the rogers one is better (though maybe not 4.4 yet)
sleepyguy007 said:
yes of course. think about it like if you took a dell windows 7 install CD , and put it on an HP. all the dell customizations would still be there.
obviously since you have unlocked bootloader, once you do the RSDlite you can always flash twrp, and superuser, and delete all that stuff. but then you wouldn't get updates again. i dont think the at&t image is really THAT bad. though i've heard the rogers one is better (though maybe not 4.4 yet)
Click to expand...
Click to collapse
Yeah unfortunately that's what I thought. Hence why I would of liked to flash the t-mobile image but I'm going to hold off until someone that is a bit more adb savvy then myself tries it out. I wouldn't know what to do if I ended up soft bricking my phone
Well it didn't take long to try it out myself...
It worked out!
I used this thread here http://forum.xda-developers.com/showthread.php?t=2446515
I downloaded the Tmobile 4.4 Image and used RSD.
All you have to do is unlock your BL. (Note: I was completely bone stock with NO root and NO special recovery like CMW or TWRP)
Have all the proper drivers installed, enable USB debugging in developer settings on the phone
Go into Fastboot on the phone
Plug in the phone and just follow the video
I do not take any responsibitliy if you brick your phone. It is fairly easy process and took only a few mins.
Hope this helps!
- deleted because I was sleepy enough not to notice that replies were done on the next page -_- -
alternetconcept said:
I've been looking through a few threads and I am not comfortable enough to flash the T-Mobile rom over my AmericanMovil one yet.
I can't seem to find step by step instructions on how to do this.. Would anyone like to explain it from the ground up?
My understanding
1) unlock bootloader
2) flash a recovery like twrp or cmw
3) flash the rom that is given in the OG post here http://forum.xda-developers.com/showthread.php?t=2477180
4) this should now give us the t-mobile version of things and we should be able to do the standard OTA from there?
[Q] So can this all be done without ever having to root the phone?
Click to expand...
Click to collapse
I've been doing some research on this since yesterday and I've been hesitant on doing it. I saw in your last post that you successfully flashed the TMO 4.4 ROM on your AmericaMovil phone, so I have a few questions for you before I go ahead and do the same:
1. Can you please confirm that your model is XT1058 and not XT1053?
2. Does the TMO ROM have the TMO boot logo and any TMO bloatware?
3. Does the TMO ROM have the Tethering & portable hotspot option under Settings > More?
4. Does the TMO ROM have the Mass Storage option under Settings > Storage > | > USB computer connection?
5. Have you been having any radio problems since you flashed the TMO ROM?
I wonder if I install the ROM in here http://forum.xda-developers.com/showthread.php?t=2477180 using RSDLite, would I get the OTA update to 4.4? The reason I want to install this ROM is because it only flashes system and boot.img without flashing bootloader, modem, logo etc... and I know the XT1058 radio is different from the XT1053 radio, so I've been reluctant to flash a full XT1053 ROM on my XT1058 phone.
But what I also would like to know is if an OTA update would flash a full ROM or not. In other words, if I flash the ROM above and then OTA update to 4.4 and the OTA update flashes the full ROM including the radio, I might as well flash the full 4.4 immediately.
What do you or anyone else think?
I'll answer to the best of my ability. heh
mschumacher69 said:
1. Can you please confirm that your model is XT1058 and not XT1053?
Click to expand...
Click to collapse
Mine was an XT1058, and has been flashed to XT1060. (I didn't notice that T-Mo had a 4.4 ROM on the list, so I went straight for the flashable ZIP for Verizon instead. silly me.)
mschumacher69 said:
2. Does the TMO ROM have the TMO boot logo and any TMO bloatware?
Click to expand...
Click to collapse
At least according to this article, the TMO version shouldn't have any bloatware.
mschumacher69 said:
4. Does the TMO ROM have the Mass Storage option under Settings > Storage > | > USB computer connection?
Click to expand...
Click to collapse
There's no reason why there shouldn't be; I'm seeing it on my Verizon version.
mschumacher69 said:
5. Have you been having any radio problems since you flashed the TMO ROM?
Click to expand...
Click to collapse
I can't say for sure if you'll face any problems, but I flashed the T-Mo radio provided here with my Verizon ROM, and I had no problems connecting to my network in Singapore.
--
I can't answer the rest unfortunately. Sorry. Hope I've helped.
RagnaParadise said:
I can't answer the rest unfortunately. Sorry. Hope I've helped.
Click to expand...
Click to collapse
Thank you for your answers!
Regarding Mass Storage, the reason I'm asking is because I don't have it on my AmericaMovil ROM.
The ROM is basically exactly what you get when you buy the T-Mobile version.
I figured the radios are nearly identical from the AT&T version and the T-Mobile version so my XT1058 is running on the XT1053 radios. There is no bloatware. tethering is there but I'm not sure if t-mobile will allow it. There is NO tmobile logo that comes up on boot. USB connect to computer is there.
As for the radio section again.. I was getting only EDGE in my house before I switched to this ROM (Meaning when I was on the ORIGINAL XT1058 image) and I am still getting only EDGE in my house.. Unfortunately I haven't left my house since yesterday flashing the image but when I'll be back at work in NYC and should see '4G/LTE' over there.
We'll see.
alternetconcept said:
The ROM is basically exactly what you get when you buy the T-Mobile version.
I figured the radios are nearly identical from the AT&T version and the T-Mobile version so my XT1058 is running on the XT1053 radios. There is no bloatware. tethering is there but I'm not sure if t-mobile will allow it. There is NO tmobile logo that comes up on boot. USB connect to computer is there.
As for the radio section again.. I was getting only EDGE in my house before I switched to this ROM (Meaning when I was on the ORIGINAL XT1058 image) and I am still getting only EDGE in my house.. Unfortunately I haven't left my house since yesterday flashing the image but when I'll be back at work in NYC and should see '4G/LTE' over there.
We'll see.
Click to expand...
Click to collapse
Thanks for ur reply! Which network are you on right now?
mschumacher69 said:
Thanks for ur reply! Which network are you on right now?
Click to expand...
Click to collapse
I've always been on T-mobile network. Both when i was on original XT1058 AmericanMovil system version and still on T-mobile when I switched the image to XT1053.
Back on my Nexus 4 though.. I would have HSPA+ in my house.. So I thought it was a bit odd that as soon as I received this phone that I wasn't getting anything other than EDGE..
Will an ota push to put the n6 on a verizon build like LMY47E if its currently on LMY47M and I put a vzw sim in it? Everything works now, just curious if it'll come automatically or if i need to load it manually.
Restola said:
Will an ota push to put the n6 on a verizon build like LMY47E if its currently on LMY47M and I put a vzw sim in it? Everything works now, just curious if it'll come automatically or if i need to load it manually.
Click to expand...
Click to collapse
Probably not. If you're not on E, when Verizon finally releases the OTA, you won't get it.
Thanks. Decided to unlock and flash lmy47e to avoid any issues.
Hi,
Can you please tell me how did you flash lmy47e?
I tried doing that with wugs toolkit, but it just hangs.
Thanks.
NeoMorpheus1337 said:
Hi,
Can you please tell me how did you flash lmy47e?
I tried doing that with wugs toolkit, but it just hangs.
Thanks.
Click to expand...
Click to collapse
Properly, without a toolkit.
Images are here:
https://developers.google.com/android/nexus/images
You need to use fastboot.
All guides and info threads are in general > Sticky roll-up
I've been googling around and reading threads ... want to get Lollipop on my Sprint Moto X.
But quite confused by all the different versions.
Currently I have
- unlocked bootloader
- rooted
- TWRP recovery
- unlocked by Sprint for Int'l use
And this:
Code:
baseband
MSM8960PRO_BP_2323.038.123.00R
Kernel 3.4.42-gcac35be
[email protected] #1
HW version
P30
System version
212.44.28.ghost_sprint.Sprint.en.US
Build number
KXA21.12-L1.28
I do NOT care about every using Sprint again; I just want to be able to use GSM SIM in Europe.
If someone could please verify what I've gleaned ...
As I understand, I would need to
1. Flash the XT1053 4.4.4 from https://cloud.mail.ru/public/64a43f0fcc1e/Moto_X/Official_XT1053/
I do this from TWRP, yes?
2. Then flash a XT1053 5.0 or 5.1 from ... where?
Can I use this Verizon one? http://forum.xda-developers.com/moto-x-2014/general/vzw-5-1-soak-ota-t3144689
.... if I flash a Verizon 4.4.4?
3. Then I would need to re-unlock for int'l SIM ... as per http://forum.xda-developers.com/moto-x/general/guide-success-sim-unlock-sprint-xt1056-t2825155
But only change the NV-ITEM thing, not the SPC thing?
Or do I do that BEFORE flashing Lollipop?
Again, I do NOT care about every using CDMA/Sprint again.
But I do want GSM SIM with LTE in Europe.
Thanks!
There is no updates until now, you can get some info in here
also its able to flash any custom ROM like CM12.1 or any other via recovery
Any news?
Hi, did you try anything?
I have XT1049, manually flashed it to 5.1 with XT1056 rom, it worked fine, but than I installed another update to fix stagefright and since than phone does not detect sim card, you can read my whole story here
I just wanted to know if you had tried anything about installing lollipop? XT1049 and 1056 are almost identical hardware so we are in the same boat of being in the minority
I ended up just flashing the XT1053 version from this:
http://forum.xda-developers.com/moto-x/development/xt1053-retail-stock-lollipop-flashable-t3155843
and it's been working fine.
d0g said:
I ended up just flashing the XT1053 version from this:
http://forum.xda-developers.com/moto-x/development/xt1053-retail-stock-lollipop-flashable-t3155843
and it's been working fine.
Click to expand...
Click to collapse
I did the same, but what did you do with the stagefright? Didn't you get OTA notification right after you installed lollipop, it should have been stagefright fix?
Thanks for your response, it's very important for me, trying to figure out what to do my "No sim card detected" XT1049.
0bser said:
I did the same, but what did you do with the stagefright? Didn't you get OTA notification right after you installed lollipop, it should have been stagefright fix?
Thanks for your response, it's very important for me, trying to figure out what to do my "No sim card detected" XT1049.
Click to expand...
Click to collapse
(a) It was a few months ago, so I don't remember exactly what 'happened' -- but I don't recall getting any OTA notification
(b) I am in Europe, so haven't connected to Sprint network at all since then
(c) Mine is a 1056, so may be different ...
Sorry, wish I could help, but I'm not nearly expert enough to advise!
I assume you've done the idiotic stuff, like cleaning your SIM card, re-seating it, trying a different SIM, etc...
Yes, tried everything including sim cleaning etc.
I'm not in US neither, nor am I using Sprint.
Could you check and send your system version and baseband version please?
I might figure out something from it.
And if you remember did you directly flash XT1053 on 4.4.2? Or did you flash XT1053 4.4.4 first and then lollipop ,as you have written in OP here?
I unlocked the bootloader on my XT1096 (verizon) Moto X 2014. Currently running stock 5.1 ROM.
What's the best way to get Marshmallow on? Can I use a ROM from another model? Do I need to flash a recovery? Thanks.
jonnythan said:
I unlocked the bootloader on my XT1096 (verizon) Moto X 2014. Currently running stock 5.1 ROM.
What's the best way to get Marshmallow on? Can I use a ROM from another model? Do I need to flash a recovery? Thanks.
Click to expand...
Click to collapse
The only way to get Marshmallow on a verizon would be with a custom rom that supports CDMA. I know that CM13 supporta CDMA so that one would work.
And while yes you could flash the rom from another model like the xt1095, it would lose verizon signal since the other models are GSM instead of CDMA.
Sent from my XT1095 using Tapatalk
tomas1pit said in the bootloader unlock thread:
"if u want to convert your device dont forget about NON-HLOS.bin and fsg.mbn. That is modem files. U should take them from official 5.1 image for xt1097 otherwise your network wont work"
Would I be able to flash the XT1095 stock MM image and then copy those files over, retaining Verizon signal?
jonnythan said:
tomas1pit said in the bootloader unlock thread:
"if u want to convert your device dont forget about NON-HLOS.bin and fsg.mbn. That is modem files. U should take them from official 5.1 image for xt1097 otherwise your network wont work"
Would I be able to flash the XT1095 stock MM image and then copy those files over, retaining Verizon signal?
Click to expand...
Click to collapse
tomas1pit is incorrect, if you look in other threads of people that have unlocked bootloaders with verizon, they lose signal completely if they convert to another model. He does not realize that xt1096 is CDMA, the NON-HLOS.bin and fsg.mbn apply to GSM.
You can still get signal if you change to another model, but only if you put a sim chip in your phone for AT&T, T-Mobile, etc since those companies are GSM. The problem is that switching firmware makes it incompatible with verizon.
If you plan to stay with verizon, custom roms are your only choice. If you change to a GSM company then you can use the stock firmware from another model.
Sent from my XT1095 using Tapatalk
Roger. Thanks.
It took a few tries to get TWRP on... I had to use crpalmer's custom version, the regular version didn't work. I'll hunt around for a custom ROM. If anyone has any suggestions (as close to stock Android as possible) I'd appreciate it.
jonnythan said:
Roger. Thanks.
It took a few tries to get TWRP on... I had to use crpalmer's custom version, the regular version didn't work. I'll hunt around for a custom ROM. If anyone has any suggestions (as close to stock Android as possible) I'd appreciate it.
Click to expand...
Click to collapse
No problem. Your best bet would be to read the custom rom threads and see if any say they support cdma. Or post in the thread to ask the developer if it does.
The only one I know for sure works with verizon is CM13, since I have read that some verizon users have tried it and it worked for them. I assume that roms that are based off CM might work, but you know what they say about assuming... Anyway good luck finding a rom you like.
Sent from my XT1095 using Tapatalk
I unlocked the bootloader on Verizon xt1096 Android 5.1, installed latest twrp recovery and installed SuperSU and am rooted. Woot. Twrp is super useful! I'd just be careful with what you're flashing of course.
I couldn't get official TWRP to work, but this custom version worked for me:
https://www.dropbox.com/s/t4wbyl4ge807r31/openrecovery-20150308-victara-UNOFFICIAL.img?dl=0
After I installed TWRP, I just flashed SuperSU and got root.
jonnythan said:
I couldn't get official TWRP to work, but this custom version worked for me:
https://www.dropbox.com/s/t4wbyl4ge807r31/openrecovery-20150308-victara-UNOFFICIAL.img?dl=0
After I installed TWRP, I just flashed SuperSU and got root.
Click to expand...
Click to collapse
Have you tried flashing any roms yet for marshmallow?
pianoman102 said:
Have you tried flashing any roms yet for marshmallow?
Click to expand...
Click to collapse
I haven't had time yet.
Same situation. Just recently unlocked the bootloader on my XT1096 (Verizon Moto X 2). Trying to figure out how to get to Marshmallow (stock or rooted) but with Verizon radios. Can't seem to find XT1096/Verizon radios in a flashable zip.
[/COLOR]
mtoomey79 said:
I then took the OTA upgrade to 5.0 which totally hard bricked it.
Click to expand...
Click to collapse
So yeah @jonnythan if you want to help me unbrick my phone...
If there's anything I can do to help, I'd be happy to. There's probably not much I can do, though.
jonnythan said:
If there's anything I can do to help, I'd be happy to. There's probably not much I can do, though.
Click to expand...
Click to collapse
Just a little humor. I have reached out to KidJoe here for some help. I also reached out to MotoCare and they are sending me a new MotoX (for me to tinker with some more).
I would suggest that we need to find a way to get the XT1096 to XT1095, while keeping factory bootloader to accept future OTAs. The VZW radios are out there, just will need to flash them via ADB if/when new OTAs come though.
So for right now, no other custom rom will work with the xt1096 unless somebody makes it specifically or customizes a different rom to suit it right?
CM13 and derived ROMS should work. There are other non-Marshmallow ROMs, I think.
jonnythan said:
I couldn't get official TWRP to work, but this custom version worked for me:
https://www.dropbox.com/s/t4wbyl4ge807r31/openrecovery-20150308-victara-UNOFFICIAL.img?dl=0
After I installed TWRP, I just flashed SuperSU and got root.
Click to expand...
Click to collapse
Where did you get this? All the official TWRP builds throw a mismatched partition size error and won't install.
If I understand correctly, if I'm not using the phone on Verizon I can install any ROM?
crpalmer posted it in the CM12 thread.
I was able to get the latest TWRP installed. Took a few attempts.
i flashed mine with twrp it said the same thing when i fastbbot flashed it but it worked i just booted in recovery any ways and it worked
Edit: I flashed to US Cellular not US Unlocked.
Currently flashed:
v405UA020g_00_USC_UYS_OP_0424.kdz
Is there an alternative place I can find Sprint kdz, downgrade to US unlocked or some way to restore LTE service.
As far as I can tell I might be able to root and then flash a custom firmware using TWRP and then downgrade onto US Unlocked.
Can anyone confirm that is the correct course of action?
Why make it hard?
Just flash the US unlocked version via LGUP.
That works with Sprint well.
And no, there is no Sprint KDZ available.
[NG]Owner
NGOwner said:
Why make it hard?
Just flash the US unlocked version via LGUP.
That works with Sprint well.
And no, there is no Sprint KDZ available.
[NG]Owner
Click to expand...
Click to collapse
Thank you so much for your reply.
When I try and flash the us unlocked via refurbish or upgrade I keep getting an anti-rollback error, something like USCELL>Unlocked or something like that.
Got frustrated in the middle of typing that and tried botching a refurb by unplugging in the middle and was able to get US unlocked on there afterwards.
xanxor said:
Thank you so much for your reply.
When I try and flash the us unlocked via refurbish or upgrade I keep getting an anti-rollback error, something like USCELL>Unlocked or something like that.
Got frustrated in the middle of typing that and tried botching a refurb by unplugging in the middle and was able to get US unlocked on there afterwards.
Click to expand...
Click to collapse
Try the method I stated in my guide not refurbish or upgrade