Database Develop

[Q] Stuck on LG logo after CM7! help!

I recently installed CM7 after rooting my phone with Superoneclick and installing Clockworkmod. However, after installation of CM7, i managed to boot up the system, played around with it and realised that i needed to install the google addon as well. So i rebooted the phone to enter into CWM recovery, however the problem started.
My phone is now stucked on the LG logo screen and would not change. I left the phone in that state till the battery went dead. Recharged the phone and it remained on that screen.
Tried to connect the phone to the PC to flash it with smartflash, but it doesnt work at all. I removed the battery and held the volume down button while plugging in the usb cable. All i see is the phone stucked on the white LG logo screen.
Is there any way that i can reformat the contents of the phone or is my phone certified?
All help would be much appreciated!

Power up directly to cwm by pressing power button and volume down key at the same time.
Once in cwm, full wipe including /system and reflash cm and gapps.
Good luck.

I have tried that method as well. Sorry. Forgot to mention it in my initial post. It didn't work. I have tried to pull the battery, hold down the volume down and power button for at least 20 times now. Each time i get the same screen. The CWM menu does not come up.
Any other ways?

audilogic said:
I have tried that method as well. Sorry. Forgot to mention it in my initial post. It didn't work. I have tried to pull the battery, hold down the volume down and power button for at least 20 times now. Each time i get the same screen. The CWM menu does not come up.
Any other ways?
Click to expand...
Click to collapse
Hmm.....if u can't power to cwm directly then perhaps try smartflash to any stock rom.
1. Download any stock rom
2. Start smartflash app from pc
3. In power off mode, just press volume down to boot to software update screen. Start smartflash stock rom.
4. Boot up stock rom
5. Install rom manager and flash cwm from rom manager. (Or download cwm from Rusty! Cwm thread)
6. Boot to recovery
7. Flash cm rom
8. Flash gapps

Remove battery, hold both vol buttons and plug in USB. Screen should stay blank, but Windows will pick up an APX device. Now NVFlash back to stock and start again.

yup, tried the exact method that you suggested too. But it doesnt work. Still gets stuck at the LG logo.

Rusty! said:
Remove battery, hold both vol buttons and plug in USB. Screen should stay blank, but Windows will pick up an APX device. Now NVFlash back to stock and start again.
Click to expand...
Click to collapse
This method worked! But i have another problem, windows found an APX device, tried to install it but failed. It says driver was not found. Do i have to install a specific driver for this to work? Thanks!

Yes, good point: http://android.modaco.com/topic/335...k-rom-release-v10b-dated-1300166062-15032011/

I have managed to flash the phone and it is back working now. Thank you so much for your help rusty and temasek!

Hi, first post, hope the thread is not too old.
Unfortunately this is my best chance.
I have the same problem on my O1:
Updated from mik's beta 6.5.7 to beta 6.5.8 with the clockwork manager, at the reboot, I was stuck on lg logo.
Unfortunately usb + both volume buttons didn't work.
It remains still at the lg logo.
Pressing home + both volume, it repeately reboots.
In every case I can't go in recovery mode, so I can't wipe the system folder.
Any help will be appreciated,
thank for your time!
PS: sorry, maybe thread in p500, cm7 will be more appropriate.

hold power button + volume down button for 5-10 seconds may work, phone will reboot into recovery mode, then you are able to flash a stock rom or restore your nandroid-backup (if you made one)
good luck, hope it helps you

thanks, I saw a useful post here:
http://forum.xda-developers.com/showthread.php?p=18531050#post18531050
Then I proceded as you wrote.
Now I'm stuck at adroid logo, without the chance to wipe cache.
The recovery does not start: loading bar and then forced reboot...
I don't know what to do

nvflash
maybe you try this link
android.modaco.com/topic/335416-nvflash-setup-instructions-drivers-links-active/
Sorry, i don't get the link working, copy it in your browser, then it should work (i'm posting with my phone that's why the link is'nt correct, but it works with browser, i tried it out)

If the link doesnt work, search 'nvflash lg p990 instructions' with google, you'll see the modaco website with the instructions and the download links
Sent from my Optimus 2X using XDA App

Thank you. A few hours ago, I managed to make it working.
Thanks for your answers, I appreciated.

nvflash is the way to go. Always make sure to use the usb ports on your motherboard (back of your computer) and not some usb hub or so.
Had a black screen for 8 hours, not able to boot, flash, recover or anything.
Changed usb port and I was able to flash the phone again.

[Q] Stuck on boot animation

I tried to update to the newest CM 10 nightly (12/30 from the 12/22) and now I'm stuck on the boot animation. Any ideas? Thanks in advance...

Press and hold both the power and home button to turn it off. Then reboot if the same happens again turn it off and reboot into recovery and restore a back up.
Download again and trying re-flashing . I assume you have already done the acmeinstaller 3 with your earlier build.

sstar said:
Press and hold both the power and home button to turn it off. Then reboot if the same happens again turn it off and reboot into recovery and restore a back up.
Download again and trying re-flashing . I assume you have already done the acmeinstaller 3 with your earlier build.
Click to expand...
Click to collapse
It worked! Thanks, appreciate it. I wasn't holding down the power and home button long enough. doh! Plus, apparently, I was only on CM9 (just recently got the TP off Craigslist and have only used it sporadically, paying more attention right now to my shiny new Nexus 4).

scott62185 said:
It worked! Thanks, appreciate it. I wasn't holding down the power and home button long enough. doh! Plus, apparently, I was only on CM9 (just recently got the TP off Craigslist and have only used it sporadically, paying more attention right now to my shiny new Nexus 4).
Click to expand...
Click to collapse
You're welcome , if you want to install jcsullins CM10 you will need to upgrade to acmeinstaller 3 this is a good guide http://rootzwiki.com/topic/31548-ho...16-with-sound-camera-microphone-updated-1513/ . Otherwise you can still try CM10 but use Oat's slimmed down rom and gapps here http://forum.xda-developers.com/showthread.php?t=2062953 the links are in the first post also see this post to add camera /gallery and themes http://forum.xda-developers.com/showpost.php?p=36063602&postcount=118 .
Probably best to get used to the tablet first and don't forget to make a backup with your recovery before making any changes.
Have fun.

[Q] HELP - I think I have killed my Touchpad

I am hoping someone can assist me. I have had Android loaded for over 2 years now, and I somehow may have killed it yesterday. Here is what happened. Please help me revive my favorite tablet.
I was going to load Jelly Bean 4.3 and saw in that for most of the ROMs, it recommended to increase system partition to 512 and provided a link. I downloaded the zip file.
I have TWRP, so booted to TWRP and then performed a Factory Reset Wipe, which deletes everything, and is what I do always before a clean install of a new Android version.
I installed the "File to increase partition size to 512".
The next step was to install the ROM, but when I clicked install in TWRP (it is an install program that has some touch capabilities), TWRP just looked back to the home screen, and I go the message:
"No system found". or something similar.
It was in a loop, so I decided to click Reboot to see if I could boot back in to WebOS or my last Jelly Bean version.
When I clicked reboot in TWRP, it said rebooting at the top, but the progress bar didn't move for 15 minutes.
While this was happening, I could not click anything in TWRP, when I touched the Power key, it when to a screen that did nothing, other than let me back to the previous screen if I swiped it, like a confirmation message. It just took me back to the screen where it was locked.
I figured I was well on the way to trouble, so I decided to hard shut down while it was in this state.
I pushed Home, Power, and Volume Up/Down keys until it flickered and the power went off.
Now, I cannot get it to show any life.
I plugged it in and charged it, but still not response.
Can I get it to connect as a USB even though it is unresponsive? Maybe to start over with WebOS Doctor?
Or, is there something else to try?
Please help me, XDA Dev community. I will try anything.
Thank you in advance for your help.

did you find fix
hptjurgensj said:
I am hoping someone can assist me. I have had Android loaded for over 2 years now, and I somehow may have killed it yesterday. Here is what happened. Please help me revive my favorite tablet.
I was going to load Jelly Bean 4.3 and saw in that for most of the ROMs, it recommended to increase system partition to 512 and provided a link. I downloaded the zip file.
I have TWRP, so booted to TWRP and then performed a Factory Reset Wipe, which deletes everything, and is what I do always before a clean install of a new Android version.
I installed the "File to increase partition size to 512".
The next step was to install the ROM, but when I clicked install in TWRP (it is an install program that has some touch capabilities), TWRP just looked back to the home screen, and I go the message:
"No system found". or something similar.
It was in a loop, so I decided to click Reboot to see if I could boot back in to WebOS or my last Jelly Bean version.
When I clicked reboot in TWRP, it said rebooting at the top, but the progress bar didn't move for 15 minutes.
While this was happening, I could not click anything in TWRP, when I touched the Power key, it when to a screen that did nothing, other than let me back to the previous screen if I swiped it, like a confirmation message. It just took me back to the screen where it was locked.
I figured I was well on the way to trouble, so I decided to hard shut down while it was in this state.
I pushed Home, Power, and Volume Up/Down keys until it flickered and the power went off.
Now, I cannot get it to show any life.
I plugged it in and charged it, but still not response.
Can I get it to connect as a USB even though it is unresponsive? Maybe to start over with WebOS Doctor?
Or, is there something else to try?
Please help me, XDA Dev community. I will try anything.
Thank you in advance for your help.
Click to expand...
Click to collapse
I have the same Prob .it will not start did you find a fix? if so could pass it on thanks

Found Fix
I ended up visiting the tpdebrick-v004 thread on rootzwiki. I booted my PC to LINUX 12.04 Live CD and applied the fix. I also ended up charging it for 2 days and it finally powered on. I then did a WebOS Doctor - plenty of instructions on how to do this. Then I used ACMEUninstaller2 to fully remove all Android. Then, I installed the latest CM10.1 with ACMEInstaller5, which automatically increases the partition to 600MB. Took 2 days off and on to do all of this but it worked.
The first step is to charge the battery for 1 full day, then press Power+Home to try to reset. If that doesn't work, try to push Power only, and boot into WebOS if you get this option. From there, you will be ready to start restoring.
If your problem is something other than what I have, the solution that fixes 95% of TP brick problems is tpdebrick-v004 by JCSullins. That should fix you.
Thanks

a fix for hp
:laugh:
hptjurgensj said:
I am hoping someone can assist me. I have had Android loaded for over 2 years now, and I somehow may have killed it yesterday. Here is what happened. Please help me revive my favorite tablet.
I was going to load Jelly Bean 4.3 and saw in that for most of the ROMs, it recommended to increase system partition to 512 and provided a link. I downloaded the zip file.
I have TWRP, so booted to TWRP and then performed a Factory Reset Wipe, which deletes everything, and is what I do always before a clean install of a new Android version.
I installed the "File to increase partition size to 512".
The next step was to install the ROM, but when I clicked install in TWRP (it is an install program that has some touch capabilities), TWRP just looked back to the home screen, and I go the message:
"No system found". or something similar.
It was in a loop, so I decided to click Reboot to see if I could boot back in to WebOS or my last Jelly Bean version.
When I clicked reboot in TWRP, it said rebooting at the top, but the progress bar didn't move for 15 minutes.
While this was happening, I could not click anything in TWRP, when I touched the Power key, it when to a screen that did nothing, other than let me back to the previous screen if I swiped it, like a confirmation message. It just took me back to the screen where it was locked.
I figured I was well on the way to trouble, so I decided to hard shut down while it was in this state.
I pushed Home, Power, and Volume Up/Down keys until it flickered and the power went off.
Now, I cannot get it to show any life.
I plugged it in and charged it, but still not response.
Can I get it to connect as a USB even though it is unresponsive? Maybe to start over with WebOS Doctor?
Or, is there something else to try?
Please help me, XDA Dev community. I will try anything.
Thank you in advance for your help.
Click to expand...
Click to collapse
this worked for my tp good luck
1. Plug the charger in and connect it to your touchpad.
2. Press and hold home+power together for 1 minute. If no response, release, then hold both for 1 minute again.
3. If 2 does not work, keep the charger connected, release the buttons (2) then press and hold home+power+volume up together for 1 minute. Release, then press and hold home+power for 1 minute.

morningforest said:
:laugh:
this worked for my tp good luck
1. Plug the charger in and connect it to your touchpad.
2. Press and hold home+power together for 1 minute. If no response, release, then hold both for 1 minute again.
3. If 2 does not work, keep the charger connected, release the buttons (2) then press and hold home+power+volume up together for 1 minute. Release, then press and hold home+power for 1 minute.
Click to expand...
Click to collapse
If that didn't work, try pressing the power and Up volume button at the same time. This should show the usb logo. Use WebOs Doctor to revive the tablet. This will wack moboot. Use ACMEInstaller 5 on the pc to install moboot (0.3.8), CWM or TWRP zips from the webos /cminstall folder.

Help - Stuck in moboot 0.3.5!

Sorry for the possibly FAQ nature of the request. I installed CM9 probably over 18mos on my daughter's Touchpad and was going to update it to JCSullins CM11 ROM. I got all the files downloaded and was getting ready to perform the complete uninstall of CM. Once I rebooted into the moboot 0.3.5 menu I was trying to select the 'boot webOS recovery' option, but no combination of power button + vol up or down seems to do anything except move the menu selection up/down. I can't seem to do anything to actually 'select' an option from the menu. I've tried long press power and short press power both with and without the vol up/down held. I'm hoping I can avoid having to open the unit to disconnect the battery but right now I'm not sure what I can do. Again it's been a long time since I did anything with the Touchpad and when I did the initial CM9 install everything went very smoothly once I got Novacom installed and ran the ACMEInstaller script. I'm hoping there's a simple trick I missed that will help get me out of the moboot screen.
-OK - sorry for the idiot post here, I just figured out the select is the 'front' button on the screen. Feel stupid but got it working! Hopefully I'll have the new CM11 up and running for my daughter tomorrow !

[Q] SystemUI stopped working

I was freezing some apps in my app manager Think it was called rom box or something. When I closed the program, I got a message that com.systemui stopped working. Now my touchscreen isn't working.
I have a backup from earlier today on my pc but I cannot get it to my phone as it doesn't show up when I plug it in to my pc. My phone is an LG G2 Verizon with TWRP.recovery.
Not sure what options I have here.
I am running stock build I believe 4.2.2 kitkat
First post. Sorry if this is vague and needs more info. Can't really get anything off my phone
Thanks for any help!

xxdaman1200xx said:
I was freezing some apps in my app manager Think it was called rom box or something. When I closed the program, I got a message that com.systemui stopped working. Now my touchscreen isn't working.
I have a backup from earlier today on my pc but I cannot get it to my phone as it doesn't show up when I plug it in to my pc. My phone is an LG G2 Verizon with TWRP.recovery.
Not sure what options I have here.
I am running stock build I believe 4.2.2 kitkat
First post. Sorry if this is vague and needs more info. Can't really get anything off my phone
Thanks for any help!
Click to expand...
Click to collapse
Power it off, follow the key sequence to get into recovery...
Press power and volume down, hold til LG Logo, let off and immediately press them both again, hold til you get the factory data reset screen, hit power twice to boot to TWRP.

mjones73 said:
Power it off, follow the key sequence to get into recovery...
Press power and volume down, hold til LG Logo, let off and immediately press them both again, hold til you get the factory data reset screen, hit power twice to boot to TWRP.
Click to expand...
Click to collapse
Yeah I ended up resetting to factory defaults last night. Connected phone back to pc and moved over the backup and booted to TWRP and restored.
Thanks!