Database Develop

Guides Alpharevx , Rooting and Much Moree !!

1st of all alpharevx works for both Froyo & GB confirmed and tested by a official alpharevx team member !!
* Steps :
1. Settings->Power->Uncheck Fastboot
2. Run latest version of HTC Sync on your PC and connect phone in HTC Sync mode and sync all your files.Remove HTC Sync and not the drivers ..
3. Reboot phone.
4. Settings->Applications->Development->Check USB Debugging
5. Run AlphaRevX and connect phone to PC in Charge Only mode
6. AlphaRevX should recognise your phone and show your Device Serial number, typically it should be something like HTXXETDXXXXX
7. Now type this out in the AlphaRevX page, the Key Generator appears only after you click the 'Download for Windows' link
8. Type out the key in the AlphaRevX software, keeping in mind the upper and lower case letters and press enter
9. AlphaRevX should start doing its thing and I got S-OFF at my first attempt in under 90 seconds
10. If it takes longer, just wait for the 15 minutes mark, if nothing, then reboot phone and retry. Some members got S-OFF after multiple tries
*After a successfull S-OFF
http://forum.xda-developers.com/showthread.php?p=14693680
for : fastboot wait device
power on ur phone pressing volume down + power button ..
run the neccessary commands on windows cmd prompt , when it shows wait for device
then click on fastboot on the phone's screen . here click is enabled by pressing the power button !!
* Make sure you have disabled your antivirus and firewall !!
On windows7 if UAC is enable make sure you right click and run it as administrator
Special thanks to JohnAnderton on this info :
If AlphaRevX isn't working for you (kept "hanging" at Step 2 i.e. attempting to get root). This was because AlphaRevX doesn't work with certain carrier variants are GingerBreak patched
It didn't work for me on the India/Asia version.
To check your software version, go to settings > about > software version > build version. If it says 2.12.720.5, I'm sorry but you'll have to do the Optus/Virgin AU ROM installation.
Here are the steps to do that:
1) Download the Optus ROM (261 MB)
2) create a gold card
3) run the ROM installer and wait for it to extract, go to your tmp folder (start > run > %tmp% > sort by date > see newest folder > dig in deep and find rom.zip)
4) take rom.zip and put it on your SD with the name PG32IMG.zip
5) Reboot your phone into boot loader (this can be done by switching your phone off, waiting 5 seconds, turning your phone on with the volume down pressed). It will see that you have PG35IMG.zip so it will verify and install it. It will come to the boot loader again and once it's done installing it will load the OS (the regular HTC white page followed by Optus' logo. Once you're in the OS, remove PG32IMG.zip
Special thanks to Cardii :
Permanent Root using Gingerbreak v1.2. Just follow these steps.
1. Download Astro File Manager (Free or Paid)
2. Download Gingerbreak v1.2 from the Gingerbreak thread on XDA (Google it)
3. Place Gingerbreak.apk on your SD Card (no format required)
4. Run Astro File Manager and install Gingerbreak
5. Reboot phone
6. Open Gingerbreak and click Root Device
7. Takes a few mins to root, phone should automatically boot and if you find Superuser installed then you have permanent root. In some cases you might have not have an automatic reboot, in that case you'll get a message along these lines 'Reboot has failed, please reboot manually and check if Superuser has been installed'. If the process is hanging at the 'Rooting Device' for longer than 10 mins, just reboot the phone and try again.
8. You should have root.
if its not rooting by this method try another sd card manually format it and den give it a try .. it should work
for gingerbreak v1.2 refer to this thread : http://forum.xda-developers.com/showthread.php?t=1044765
For installing custom roms follow the guide here :
http://forum.xda-developers.com/showpost.php?p=14924283&postcount=83
and if u get stuck in step 2 follow this :
http://forum.xda-developers.com/showpost.php?p=14865832&postcount=32
About Radio for S-off:
http://forum.xda-developers.com/showpost.php?p=15023458&postcount=6
How to Use AlphaRev's tool to S-Off your Incredible S [ Video ]:
http://www.youtube.com/watch?v=XshvRmAcgm8

Great write up. . Find try tomorrow.
Sent from my HTC Incredible S using XDA Premium App

what's the command line text for step 3?
"fastboot flash recovery recovery.img" ?

yes it is the command line ..
fastboot flash recovery recovery.img
make sure you are in the directory where recovery.img is present

thanks, but first things first. need to be able to s-off my phone first =)

HELP
nikhil007mmus said:
1st of all alpharevx works for both Froyo & GB confirmed and tested by a official alpharevx team member !!
* Steps :
1. Settings->Power->Uncheck Fastboot
2. Run latest version of HTC Sync on your PC and connect phone in HTC Sync mode and sync all your files.Remove HTC Sync and not the drivers ..
3. Reboot phone.
4. Settings->Applications->Development->Check USB Debugging
5. Run AlphaRevX and connect phone to PC in Charge Only mode
6. AlphaRevX should recognise your phone and show your Device Serial number, typically it should be something like HTXXETDXXXXX
7. Now type this out in the AlphaRevX page, the Key Generator appears only after you click the 'Download for Windows' link
8. Type out the key in the AlphaRevX software, keeping in mind the upper and lower case letters and press enter
9. AlphaRevX should start doing its thing and I got S-OFF at my first attempt in under 90 seconds
10. If it takes longer, just wait for the 15 minutes mark, if nothing, then reboot phone and retry. Some members got S-OFF after multiple tries
*After a successfull S-OFF
http://forum.xda-developers.com/showthread.php?p=14693680
for : fastboot wait device
power on ur phone pressing volume down + power button ..
run the neccessary commands on windows cmd prompt , when it shows wait for device
then click on fastboot on the phone's screen . here click is enabled by pressing the power button !!
* Make sure you have disabled your antivirus and firewall !!
On windows7 if UAC is enable make sure you right click and run it as administrator
Click to expand...
Click to collapse
@NikhilI have windows 7 x64 have latest version of HTC Sync installed -I have just used it for the App installer fearture never used the SYNC now function on the phone.
When I connect the phone with USB debug mode and launch the AplharevX it gets stuck on the Aquiring root (method 2(... Step and i have tried many times to reboot the phone but NO JOY still S ON. Can you please help me isolate why Im not having any sucess with this S OFF tool. and how to uninstall HTC Sync and still keep the drivers ? Thanks

just normal uninstall the htc sync thats all no need to do nethng special for that !! and connect ur phone in charge only mode !!

nikhil007mmus said:
just normal uninstall the htc sync thats all no need to do nethng special for that !! and connect ur phone in charge only mode !!
Click to expand...
Click to collapse
Will do this ... also is it important to do the Sync Now feature on the phone? Because I dont wana sync my outlook contacts? as they are diffrent from my google and facebook contact list?

how to remove htc sync but not the drivers? just uninstall normally?
edit: sorry didnt see the replies!
still stuck at method 2 though...

bernlim said:
how to remove htc sync but not the drivers? just uninstall normally?
edit: sorry didnt see the replies!
still stuck at method 2 though...
Click to expand...
Click to collapse
are u still stuck after uninstalling HTC sync > reboot PC
and doing the entire process again ?
r u on windows 7 64 bit version too?

guys try setting your phone to airplane mode, think that did the trick for me

what the heck, i'm going to try that

Can someone now please post a detailed step by step guide on how to permanently root the Incredible S. I'm a noob and the guide posted by attn1 leaves me a bit clueless.

it's in the orginal post dude

That is for S-OFF, I've seen the permanent root guide by attn1, but I need a more detailed guide, I don't really get the first post.

baste07 said:
what the heck, i'm going to try that
Click to expand...
Click to collapse
R u still facing problems to get S off on a windows machine?? Do you have access to a Linux machine or may be a Virtual Linux ?? we can try the Linux version of the AplhaRevX

Cardiiiii said:
That is for S-OFF, I've seen the permanent root guide by attn1, but I need a more detailed guide, I don't really get the first post.
Click to expand...
Click to collapse
read the post again well man, there's a link for things to do after s-off.
you've seen Attn1's post? and can't understand it?

muk12 said:
R u still facing problems to get S off on a windows machine?? Do you have access to a Linux machine or may be a Virtual Linux ?? we can try the Linux version of the AplhaRevX
Click to expand...
Click to collapse
sad to say i don't, but someone just confirmed that asian roms will fail using alpharevx

WOOOT WOOOT!!!! IM DONE!!!!
Just bought my RED IS yesterday and the S-off procedure was out!
Read the two threads, and then followed this!!! WOOT AGAIN! got s-off!!!

Have you got permanent root as well?

[Q] Help... X8 trouble.

OK, first hi everybody I'm new here and will try be helpfull for other members as soon as I deal with my phone.
I bought the Xperia X8 2 months ago, tried to uprade it to gingerbread, failed and gave up. Now im trying again and i've read a lot threads here and unfortunately nothing seems to work. Cant root the stupid thing.
The phone is model E15i, it has 2.1-update1 - Frimware version, Baseband version is M76XX-TSNCJOLYM-53404015, Kernel version is 2.6.29 and 2.1.1.A.0.6 is the Build number.
I tried rooting with SuperOneClick countless times with different version of the program including latest and it always freezes, i get the Not Responding treatment. Also tried x8toolbox and again nothing. I folowed every step from other threads and it cant be rooted. I installed Root Explorer 2.16 apk but wasnt able to copy files from xRecovery to bin folder because i cant change r/o to r/w ( i guess this is because the phone is not rooted ).
Somebody please help
P.S. All suggestions are welcomed !

Bootlocker??
If u wer on the stock firmware and locked bootlocker this can actually happen. See to that u have unlocked the bootlocker. Then try to upgrade once more and if failed then there is plenty of custom roms available here on the rom section so ntng to worry abt. Its fine.
To unlock boot locker :
Turn off phone and start in fastboot mode,
Before that,
First, you should confirm that it is possible to unlock the boot loader of your phone by checking the service menu. In your phone, open the dialler and enter *#*#7378423#*#* to access the service menu.
In your phone, tap Service info > Configuration > Rooting Status. If Bootloader unlock allowed says Yes, then you can continue with the next step. If it says No, or if the status is missing, your device cannot be unlocked.
On your computer, click Continue at the bottom of this page to start the unlock boot loader process.
Read through the information in the pop up window and click Yes, I’m sure, if you are still confident you want to unlock the boot loader.
Read through and accept the legal terms. Click I Accept.
Enter your name, email address, the first 14 digits (remove the last digit) of your phone’s IMEI number and the two CAPTCHA words in the input boxes. Click Submit. You can view the IMEI number by entering *#06# on your phone.
The unlock boot loader key is displayed. Write it down and save it for later use.
Download and install the latest Android SDK from developer.android.com.
Download and unzip this file. This is the standard android_winusb.inf-file, with a few lines of code added to enable Fastboot to support Sony and Sony Ericsson devices. Make sure you are running Google USB Driver package revision 4 or higher in your Android SDK. You can see current Google USB Driver package revision in the SDK Manager.
Place the unzipped file in the usb_driver folder, located in the Android SDK > extras > google folder on your computer. Accept to replace the old android_winusb.inf-file with the new file. If you can't find the usb_driver folder, please install the Google USB Driver Packager using the Android SDK manager.
Turn off your phone.
On your phone, push and hold the unlock button* at the same time as you connect the phone to the computer with a USB-cable. The unlock button may differ between different phone models. See the note in the bottom of this page for more information on what button use on your phone.
On your computer, you will be asked for drivers. Point to the usb_driver folder where you placed the android_winusb.inf-file, and select the Android Boot loader Interface-file.
Open a command window and go to the tools folder within the Android SDK folder.
Enter fastboot.exe -i 0x0fce getvar version, and verify that you get a response back (for example "0.3"). This means your phone is connected properly.
Warning! If you perform this step, you will unlock the boot loader. This may void your warranty and/or any warranty from your operator. If you still want to unlock the boot loader of your phone, enter fastboot.exe -i 0x0fce oem unlock 0xKEY, where KEY is the unlock boot loader key you got in the beginning of this instruction. The boot loader should now be successfully unlocked.
And if u still fail come back with the error and dont frget to say thanx for my efforts(press if only it helped.)

Hi there
I would recommend you to use flashtool to root and unlock your phone. Of course it will have many other function as else.
http://www.mediafire.com/download.php?t3baob63v9grqub <== Flashtool
Don't forget to install driver & off AV
Read post until the end of it's page

mustangx8 said:
OK, first hi everybody I'm new here and will try be helpfull for other members as soon as I deal with my phone.
I bought the Xperia X8 2 months ago, tried to uprade it to gingerbread, failed and gave up. Now im trying again and i've read a lot threads here and unfortunately nothing seems to work. Cant root the stupid thing.
The phone is model E15i, it has 2.1-update1 - Frimware version, Baseband version is M76XX-TSNCJOLYM-53404015, Kernel version is 2.6.29 and 2.1.1.A.0.6 is the Build number.
I tried rooting with SuperOneClick countless times with different version of the program including latest and it always freezes, i get the Not Responding treatment. Also tried x8toolbox and again nothing. I folowed every step from other threads and it cant be rooted. I installed Root Explorer 2.16 apk but wasnt able to copy files from xRecovery to bin folder because i cant change r/o to r/w ( i guess this is because the phone is not rooted ).
Somebody please help
P.S. All suggestions are welcomed !
Click to expand...
Click to collapse
I suggest that while you are on stock ROM, "Repair" your phone with PCC to flash back stock.
Then try rooting again.

Instal pc companion lol . . Make sure a driver was install
----------------------------------------------------
Xperia X8
| MiniCM9-3.0.1 | nAa-ics-02 | 100% SuperCharger | Chainfire ?! |
Thanx to " nAa and Zeppelinrox "

To rooting (this my way)
-Install sony companion first on computer..
And turn your phone in debugging mode,,plug your phone with the computer..
(wait until the tray icon said the driver install successfully)
-unplug the device from computer
-open superoneclick click root
-when a message "waiting for device" appeared,,plug device then choose recharge
-after this mesage appeared
(Your phone has been rooted!!
Would you like to run a test??)
CHOOSE NO..
That how i rooting..
Sent from my X8 using xda premium

[Q] 'No OS installed! Are you sure you want to boot?' How to reinstall android os?

I dont know much about this stuff (def not tech savvy), but I decided to take my bad esn Sprint HTC One (running 4.3) and try to unlock it myself. I was successful in unlocking the bootloader, and I even rooted the device on my own (woo!!!). I was on the last stage of finally unlocking the phone, so I decided to go for it.
I tried to follow these steps to finally unlock my HTC One, but I did not know how to go to /system/app to replace the files (The 'Root Reader' app didn't show /system/app in my phone).
://forum.xda-developers.com/showthread.php?t=2491840
The files were:
HtcOMADM_SettingsPlugin_SPCS.apk
HtcOMADM_SPCS.apk
As a result, I tried to flash the copy files mentioned previously using this video as a guide
http://www.youtube.com/watch?v=JhR4Je4I8yw
I dragged and dropped the copies into the 'system storage' (not into a specific file) and started wiping data in TWRP 2.6 (Im assuming I wiped something that I shouldnt have). However, now whenever I try to boot my HTC One out of TWRP, I get the 'No OS installed..." message and it just just keeps showing the white screen with the HTC logo when I do boot anyways. When I connect my HTC One to my PC via usb cable, it doesnt even show up. I decided to take a screen shot of my files/drives/etc that I used. When I click on the 'instal' button in TWRP, it no longer shows the 'android' folder while scrolling through the list of things. My phone also automatically shuts off when leaving it on idle (TWRP running) for a bit, it doesnt connect to my PC anymore too
What should I do to get the phone working again? Could I unlock it from here or do I have to backtrack or something? I have very little knowledge about this stuff so please try to explain things easily for me lol

You need to relock your phone and run a ruu and to reroot your phone with the latest version of twrp 2.6 .3.0 and supersu 1.9.1 I think but you can check that when you run the ruu in the app store real quick to see if it is the latest version.

On the PC download the RUU
http://dl3.htc.com/application/RUU_..._NV_SPCS_4.38_003_release_348053_signed_2.exe
Connect USB cable to the phone to the PC (keep the phone connected until you are done)
1. Boot your phone to the bootloader (volume down and power on). Go to fastboot option on the phone menu.
2. Now using fastboot on your PC type fastboot oem lock
3. Boot your phone to the bootloader (volume down and power on). Go to fastboot option on the phone menu.
4. Now using fastboot on your PC type fastboot oem rebootRUU
5. Run the RUU that you downloaded. That will put your phone back to stock.
---------------------------------------
To unlock the bootloader:
1. Goto http://www.htcdev.com/ follow the steps.
Install custom recovery
2. Install TWRP. Download http://techerrata.com/file/twrp2/m7wls/openrecovery-twrp-2.6.3.0-m7wls.img put in in the same folder on your PC as your fastboot.exe command.
3. fastboot flash recovery openrecovery-twrp-2.6.3.0-m7wls.img
4. reboot phone.
Install root:
download http://download.chainfire.eu/351/SuperSU/UPDATE-SuperSU-v1.65.zip?retrieve_file=1
copy UPDATE-SuperSU-v1.65.zip to the phone
Boot your phone to the bootloader (volume down and power on). Go to recovery option on the phone menu. That will boot into TWRP. Use the install and install the zip UPDATE-SuperSU-v1.65.zip.

Just sideload a rom.zip
Sent from my HTC One using Tapatalk

elvisypi said:
Just sideload a rom.zip
Sent from my HTC One using Tapatalk
Click to expand...
Click to collapse
How would I do that? I just installed the HTC 4.2.001 driver to my pc as well

Moto g 2 gen's display shut downs after locking the phone or after 'screen time out'

I have Moto g 2nd Gen Indian edition phone
I have been experiencing a strange issue with my phone from past week, when I lock down my phone via power button or closing the cover of magnetic flip-shell or whether it locks it down itself after 'screen time out' automatically the display just shut downs.
The phone is actually working in background as I can see LED notification sometimes. And when I connect my phone to PC via USB it even shows the Internal storage folder. I can even feel vibration on Powering off the device.
When I try to reboot the device, it boots up normally with Motorola logo animation and everything works fine until device gets lock down and this scenario continues as I reboot it again.
Sometime I can feel the bottom speaker grill getting hotter until I 'Power Off' the device forcefully.
So far I have tried fast booting the phone it boots up normally but issue is still there.
I even tried to run the phone in the safe mode but the issue persist even in safe mode.
I even wiped cache partition and also performed 'Factory Reset' via hard reset and soft reset but nothing is working.
I want to clarify that my phone isn't under warranty and also I have not even tempered my phone's software it is completely stock with android version 5.0.2 (recently updated via OTA).
I'm not allowed to post the image as a new user that's why I have written some software specific detail as below.
System version: 22.56.3.titan_retaildsds.retaildsdsall.en.03 retin
Build No: LXB22.99-16.3
Base band version: MSM8626BP_1032.3112.96.00R EMEA_DSDS_CUST
Kernel version: 3.4.42-g0bea67a
[email protected] #1
Wed Aug 26 00:26:33 CDT 2015
I don't think the 'Power Button' can be faulty as it's working as intended properly and almost all the time I use the official Motorola 'Magnetic flip-shells' so I rarely use the power button.
I suspect that this issue may have been caused by some virus or malware as I had visited some torrent hosting and too much ad hosting sites before the issue started.
I contacted Motorola support via chat session and they asked me to get it to the service center, but I have read very bad reviews about service center near my location and I'm afraid to go there.
Although I'm a software developer but in the area of 'Android development' I'm totally noob so joined the XDA to solve the issue with the help of experts.
Can I have some suggestion, solution on this issue? Any help of yours is appreciated.
Also I want to know that if 'Hard reset' can't solve the issue, does that mean the software of device has corrupted?

Try a hard reset first
If not solved use an easy installer

vaisakmct said:
Try a hard reset first
If not solved use an easy installer
Click to expand...
Click to collapse
Well Hello sir thanks for the prompt reply, as I said earlier:
So far I have tried fast booting the phone it boots up normally but issue is still there.
I even tried to run the phone in the safe mode but the issue persist even in safe mode.
I even wiped cache partition and also performed 'Factory Reset' via hard reset and soft reset but nothing is working.
So hard reset is not working for me which I have performed 2-3 times, I guess I have to go through your another suggestion.
Ok, so by 'easy installer' did you mean this method described in below link?
http://forum.xda-developers.com/moto-g-2014/general/official-stock-firmware-5-0-2-lxb22-46-t3019612
I think method in #Post 1 is for my phone.
Does anyone have other solution or advise? Your guidance will be appreciated.

smartandcool3 said:
Well Hello sir thanks for the prompt reply, as I said earlier:
So far I have tried fast booting the phone it boots up normally but issue is still there.
I even tried to run the phone in the safe mode but the issue persist even in safe mode.
I even wiped cache partition and also performed 'Factory Reset' via hard reset and soft reset but nothing is working.
So hard reset is not working for me which I have performed 2-3 times, I guess I have to go through your another suggestion.
Ok, so by 'easy installer' did you mean this method described in below link?
http://forum.xda-developers.com/moto-g-2014/general/official-stock-firmware-5-0-2-lxb22-46-t3019612
I think method in #Post 1 is for my phone.
Does anyone have other solution or advise? Your guidance will be appreciated.
Click to expand...
Click to collapse
ya this one will be best for u

vaisakmct said:
ya this one will be best for u
Click to expand...
Click to collapse
Thank you,
The Easy installer method requires 'USB debugging enabled and RSA key Allowed', so I have enabled 'USB debugging' but I never get the 'RSA key allowed' dialogue.
I tried to attach cable to the different USB ports but I never get the 'RSA Key allowed' dialogue, How can I overcome this issue?

Thats not a pblm get in just fastboot mode click installer and select option for locked boot loader

vaisakmct said:
Thats not a pblm get in just fastboot mode click installer and select option for locked boot loader
Click to expand...
Click to collapse
but as suggested by @reefuge in post #13 and #post16 in link below
http://forum.xda-developers.com/moto-g-2014/general/official-stock-firmware-5-0-2-lxb22-46-t3019612/page2
that 'Phone must have USB debugging enabled and RSA key Allowed, Usb cable plugged in and in normal use mode'
1. I have USB debugging enabled. If I plug in my Moto G a icon appears in the Notification-Center which says "USB debugging activated please click to disable"
2. if I go into the Device Manager I can see Android Device
3. I changed my USB-Setting to PTP
but nothing works.

smartandcool3 said:
Thank you,
The Easy installer method requires 'USB debugging enabled and RSA key Allowed', so I have enabled 'USB debugging' but I never get the 'RSA key allowed' dialogue.
I tried to attach cable to the different USB ports but I never get the 'RSA Key allowed' dialogue, How can I overcome this issue?
Click to expand...
Click to collapse
no it does NOT require USB debugging anymore (that was version 1) You must be able to put phone manually into AP FASTBOOT mode by correct key combo
read instruction in zip file and attached here

reefuge said:
no it does NOT require USB debugging anymore (that was version 1) You must be able to put phone manually into AP FASTBOOT mode by correct key combo
read instruction in zip file and attached here
Click to expand...
Click to collapse
Thank you @reefuge sir for the reply.
Does that mean I don't need Phone with 'USB debugging with RSA key allowed'?
All I have to do is to run the 'Magical batch file' of yours and watch the magic show in PC?
Ok one more question, I don't want to irritate you but I'm helpless and confused,
I wanted to ask you that after following this step in sequence:
1] ALL needed files are in the zip file you downloaded TO PC (not phone) including stock ROM files
2] Install Motorola device manager 2.5.4.exe for correct Usb drivers (choose repair if already installed) and install minimal ADB /fastboot v 1.31.exe
3] plug in Usb cable and PUT phone into AP Fastboot Flash mode
4] by holding power and volume down ( - ) until phone powers off to blank screen (may vibrate)
5] still holding both buttons count 1,2,3,4,5 and release both same time
6] Hopefully you should be in AP Fastboot Flash mode with USb cable plugged in?
7] if No go back to step [3] if YES continue
8] do not select anything on phone or press any more phone buttons - All done via pc no
9] Now run the EASY INSTALLER.bat file and watch both pc screen and phone screen
I assume that your program will show me following different menu options:
1)Flash stock ROM --- will flash stock rom / Logo / boot & recovery.img / modem files and bootloader -- this DOES NOT wipe phone so can upgrade / dirty flash keeping settings
2)Lock bootloader --- as above but locks boot loader --- tbh always better to use option 1)
3)Flash Fixed Logo -- Fixes the unlocked Boot Loader Warning EVEN if unlocked still
4)Reboot Phone -- Reboots phone --
5)Factory Reset --- wipes DATA and CACHE --- IF phone hangs at BOOT LOGO, do this Action. ALWAYS use if DOWNGRADING or Coming from A CUSTOM ROM
6)Exit --- Closes command prompt window and exits
from above 6 menu options, which options do I have to follow(related to my phone's condition) in sequence to revive my phone?
I have moto g which is unrooted, stock and with locked bootloader.
You valuable reply is appreciated

smartandcool3 said:
Thank you @reefuge sir for the reply.
Does that mean I don't need Phone with 'USB debugging with RSA key allowed'?
All I have to do is to run the 'Magical batch file' of yours and watch the magic show in PC?
Ok one more question, I don't want to irritate you but I'm helpless and confused,
I wanted to ask you that after following this step in sequence:
1] ALL needed files are in the zip file you downloaded TO PC (not phone) including stock ROM files
2] Install Motorola device manager 2.5.4.exe for correct Usb drivers (choose repair if already installed) and install minimal ADB /fastboot v 1.31.exe
3] plug in Usb cable and PUT phone into AP Fastboot Flash mode
4] by holding power and volume down ( - ) until phone powers off to blank screen (may vibrate)
5] still holding both buttons count 1,2,3,4,5 and release both same time
6] Hopefully you should be in AP Fastboot Flash mode with USb cable plugged in?
7] if No go back to step [3] if YES continue
8] do not select anything on phone or press any more phone buttons - All done via pc no
9] Now run the EASY INSTALLER.bat file and watch both pc screen and phone screen
I assume that your program will show me following different menu options:
1)Flash stock ROM --- will flash stock rom / Logo / boot & recovery.img / modem files and bootloader -- this DOES NOT wipe phone so can upgrade / dirty flash keeping settings
2)Lock bootloader --- as above but locks boot loader --- tbh always better to use option 1)
3)Flash Fixed Logo -- Fixes the unlocked Boot Loader Warning EVEN if unlocked still
4)Reboot Phone -- Reboots phone --
5)Factory Reset --- wipes DATA and CACHE --- IF phone hangs at BOOT LOGO, do this Action. ALWAYS use if DOWNGRADING or Coming from A CUSTOM ROM
6)Exit --- Closes command prompt window and exits
from above 6 menu options, which options do I have to follow(related to my phone's condition) in sequence to revive my phone?
I have moto g which is unrooted, stock and with locked bootloader.
You valuable reply is appreciated
Click to expand...
Click to collapse
FORGET USB debugging and developer options, NOT required - thats NO - IGNORE , not needed
simply install mdm 2.54.exe and ADB v1.31
get phone into Fastboot mode with usb cable plugged in
run easyinstaller.bat
from menu
fmenu options choose [1] and reboot phone [4] to upgrade keeping settings
or [1], [5] and [4] to FULLY wipe and reset phone as new

reefuge said:
FORGET USB debugging and developer options, NOT required - thats NO - IGNORE , not needed
simply install mdm 2.54.exe and ADB v1.31
get phone into Fastboot mode with usb cable plugged in
run eastinstaller.bat
from menu
fmenu options choose [1] and reboot phone [4] to upgrade keeping settings
or [1], [5] and [4] to FULLY wipe and reset phone as new
Click to expand...
Click to collapse
Thank you @reefuge sir for the prompt reply and for your guidance, which actually makes the task easier for me many thanks to you sir.
I will try step '[1], [5] and [4] to FULLY wipe and reset phone as new' as mentioned, and pray to god that my days of misery gets over, to revive my phone.
Do I have to place the 'extracted folder' in my PC's root folder(which is C: drive) or I can place that 'extracted folder' anywhere on PC and execute the 'eastinstaller.bat' from there?

smartandcool3 said:
Thank you @reefuge sir for the prompt reply and for your guidance, which actually makes the task easier for me many thanks to you sir.
I will try step '[1], [5] and [4] to FULLY wipe and reset phone as new' as mentioned, and pray to god that my days of misery gets over, to revive my phone.
Do I have to place the 'extracted folder' in my PC's root folder(which is C: drive) or I can place that 'extracted folder' anywhere on PC and execute the 'eastinstaller.bat' from there?
Click to expand...
Click to collapse
anywhere as it includes (in extracted folder) ALL the files required to make it work

reefuge said:
anywhere as it includes (in extracted folder) ALL the files required to make it work
Click to expand...
Click to collapse
Thank you @reefuge sir for the reply, and I will try this 'Easy Method' and I will keep you posted on its progress.
Once again thank you very much @reefuge sir and @vaisakmct sir as your replies helped me a lot, I hope this issue get resolved soon.

smartandcool3 said:
Thank you @reefuge sir for the reply, and I will try this 'Easy Method' and I will keep you posted on its progress.
Once again thank you very much @reefuge sir and @vaisakmct sir as your replies helped me a lot, I hope this issue get resolved soon.
Click to expand...
Click to collapse
Ok, Guys I was able to run the 'EasyInstaller' and it worked perfectly and magically as it should supposed to be.
Unfortunately I was not able to resolve my problem so It might be something else.
@reefuge sir your 'EasyInstaller' was awesome, and I will highly recommend it to everyone for 1-step solution in need, please keep making these kind of awesome tools.
Thank you @reefuge sir and @vaisakmct once again for all your help. If you have anymore suggestion or solution regarding my problem please let me know.

Tutorial: Root LeEco S3

After seeing people not being able to root their S3 and rooting mine successfully, I have decided to make this tutorial to help those out there. This tutorial covers the procedures I took to successfully root my LeEco S3 US edition with EUI 5.8.018S and Snapdragon 652 processor. My phone is permantly rooted and has permanent TWRP recovery.
Make sure your phone has developer options and has usb debugging as well as the option to unlock the bootloader enabled
First off, download the AIO Toolkit created by Rishabh Rao here
Secondly, open the toolkit. Make sure to turn off your antivirus to avoid any interruptions. Once in the toolkit, select item 6 and allow the program to download necessary files. After the files have downloaded, select item 1 to install ADB/Fastboot USB drivers. During this process, PDA Net will prompt you to connect your phone to the computer. It will download the client onto your computer and install the PDA Net application onto your phone. When the drivers are fully installed, close the toolkit.
Open command prompt and run ADB. With your phone plugged in and in recovery mode, type fastboot oem unlock-go and you should see it attempting to unlock the bootloader. If you get a successful message of unlocking your bootloader, you are ready to move on to the next step as this is a temporary unlock. Close the command prompt.
Open the toolkit again, select item 6 and then select item 3 to unlock bootloader completely. When it has finished, go back to select item 4 to check and see if the bootloader has been unlocked. If so, move on to selecting item 5 to flash the latest TWRP recovery.
When the TWRP recovery has installed, if it has not booted into recovery by itself, hold down power + volume up to enter it. You will see the recovery all in the chinese language. Simply swipe the unlock to proceed and from the menu, select the box to the right and three down (which is settings). There, select the globe icon and scroll down to select the english language. Now that you can read what is there, go back to the main menu and select wipe to completely wipe the phone back to factory defaults. When it has finished, go back and select Advanced > Tools > Root Device. Your phone will now be rooted when you reboot and will have the latest TWRP recovery installed.
- If you receive the error message saying the device is locked while you are trying to unlock the bootloader from the toolkit, you need to run ADB again to temporary unlock the bootloader.

Quick question - will this only work on 18s and is it possible to update the firmware and keep root after doing this? Or would it work after updating to I think 21s which is the latest?
Thank you!

Hi
Can you break this down further with pictures too? How do I do the command prompt ABD thing?

Root
was this the easiest way? I'm going to try it in two days. Scared to mess my phone up though..

This method does not work on the 23s ROM. Does nothing

What's the best way? Simple way I mean?

Worked for anyone?

these instructions are for the le s3 with SNAPDRAGON processor, not for the MEDIATEK x20 that is where we have the problem

Just got this phone and gonna try this out, thanks ;p
---------- Post added at 11:06 AM ---------- Previous post was at 10:13 AM ----------
Actually Ima wait...I've never rooted using TWRP Recovery so not quite familiar with it after the phone's been rooted. I've only used a couple of the one-click root apps, KingRoot and KingoRoot, for a couple phones.

Rooted it fine, now I need to figure out what I can do ;P <--- noob

How were you able to successfully root the phone?
GWARslave119 said:
Rooted it fine, now I need to figure out what I can do ;P <--- noob
Click to expand...
Click to collapse
How were you able to successfully root the phone?

i dont know what to do,, it says "waiting for device" what should i do ? i already installed the 15 sec ADB something like that.. i need your help plsssss

Rooting Le S3.
XtraTerr3sTRiAL said:
After seeing people not being able to root their S3 and rooting mine successfully, I have decided to make this tutorial to help those out there. This tutorial covers the procedures I took to successfully root my LeEco S3 US edition with EUI 5.8.018S and Snapdragon 652 processor. My phone is permantly rooted and has permanent TWRP recovery.
Make sure your phone has developer options and has usb debugging as well as the option to unlock the bootloader enabled
First off, download the AIO Toolkit created by Rishabh Rao here
Secondly, open the toolkit. Make sure to turn off your antivirus to avoid any interruptions. Once in the toolkit, select item 6 and allow the program to download necessary files. After the files have downloaded, select item 1 to install ADB/Fastboot USB drivers. During this process, PDA Net will prompt you to connect your phone to the computer. It will download the client onto your computer and install the PDA Net application onto your phone. When the drivers are fully installed, close the toolkit.
Open command prompt and run ADB. With your phone plugged in and in recovery mode, type fastboot oem unlock-go and you should see it attempting to unlock the bootloader. If you get a successful message of unlocking your bootloader, you are ready to move on to the next step as this is a temporary unlock. Close the command prompt.
Open the toolkit again, select item 6 and then select item 3 to unlock bootloader completely. When it has finished, go back to select item 4 to check and see if the bootloader has been unlocked. If so, move on to selecting item 5 to flash the latest TWRP recovery.
When the TWRP recovery has installed, if it has not booted into recovery by itself, hold down power + volume up to enter it. You will see the recovery all in the chinese language. Simply swipe the unlock to proceed and from the menu, select the box to the right and three down (which is settings). There, select the globe icon and scroll down to select the english language. Now that you can read what is there, go back to the main menu and select wipe to completely wipe the phone back to factory defaults. When it has finished, go back and select Advanced > Tools > Root Device. Your phone will now be rooted when you reboot and will have the latest TWRP recovery installed.
- If you receive the error message saying the device is locked while you are trying to unlock the bootloader from the toolkit, you need to run ADB again to temporary unlock the bootloader.
Click to expand...
Click to collapse
Hi Everyone. I recently got a new le s3 x522. Its great only that sim 2 slot doesn't connect to mobile data. I have tried rooting so that I can use build prop editor to fix this, but rooting has become a real problem. I used Kingo root, framaroot but not successful. I have downloaded AIO toolkit on pc but installng is a problem. Please guide me on how to install AOI toolkit on pc. I pretty new to this things you know. Any help will be greatly appreciated.