Omni M
Welcome to the Omnirom Marshmallow thread for vibrant. I would like to thank @sooti without him this wouldn't have been possible. He put a lot of work into bringing Marshmallow to the Galaxy S1.
What is omniRom?
Code:
*
* Your warranty is now void.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you. Hard. A lot.
*/
Warning!! make sure you have a good charge in your battery, also do not disconnect battery during boot, or you will be stuck in bootloop until you use odin to flash a new kernel
Steps to install:
format data partition to f2fs in TWRP the perform a Full wipe using TWRP (and I mean full wipe! system, data, cache etc)
Install ROM
Install attached gapps
reboot and wait, it takes a long time to boot and once it does its very slow the first time so be patient
recommended: set overclock to 1400 mhz and minimum to 200 to avoid some of the lag, also reboot after setup is complete to clear some memory that wizard uses and caches
Credits
All my credits goes to sooti who work hard to bring Android M for us.
and to falconscrest123 i edit his rom to make this
also to Thanhtho96 for testing the rom
Download
ROM
gapps 6.0
Original thread
Here
Note
After flashing rom first time usage seems to be slow so be patience. If some one got lots of force closing or process stops messages just do factory reset i solves the problem. Here there is no delay in call
Screenshots
Link Updated!!!!
Audiracecar90 said:
Link Updated!!!!
Click to expand...
Click to collapse
I waited more than an our but the phone not boot. Now back with odin...
Boot fine i here
---------- Post added at 10:41 PM ---------- Previous post was at 10:41 PM ----------
Do you change data to ?f2fs
Thanhtho96 said:
Boot fine i here
---------- Post added at 10:41 PM ---------- Previous post was at 10:41 PM ----------
Do you change data to ?f2fs
Click to expand...
Click to collapse
Yes I did.
selmandeli said:
Yes I did.
Click to expand...
Click to collapse
Ok should u remove SD card and try flashing because sd card not works in M it also causes issue
selmandeli said:
Yes I did.
Click to expand...
Click to collapse
As thantho told there is no issue with booting because we both test the rom and upload it. Ok no problem if same boot loop occurs means try to flash this kernel after install rom in TWRP. Here
finally mama super
Babloo1989 said:
finally mama super
Click to expand...
Click to collapse
Thanks bro
Mine vibrant boots rom and works quick, really no delay in caller,but there are some lags:
- volume buttons upside down
- in calls i hear only on speaker mode
- long press of home button does not opening recent apps (in galaxy s tread i found solution to enable software keys, works fine)
- make a try to return to epicboy's build 5.1.1 but twrp says mine vibrant is i9000, how can i fix it?
Big shoutouts for the rom, it's great, hope it get so stable in use than my previous
Marshmallow baby!
OggyRock said:
Mine vibrant boots rom and works quick, really no delay in caller,but there are some lags:
- volume buttons upside down
- in calls i hear only on speaker mode
- long press of home button does not opening recent apps (in galaxy s tread i found solution to enable software keys, works fine)
- make a try to return to epicboy's build 5.1.1 but twrp says mine vibrant is i9000, how can i fix it?
Big shoutouts for the rom, it's great, hope it get so stable in use than my previous
Marshmallow baby!
Click to expand...
Click to collapse
Try to flash Iyahman kernel via odin and try other roms. these all problem is due to kernel issue ok when we got clean kernel all problem solved
where can I find twrp for the vibrant I can't seem to find it and it shows as not supported.
djeddieone said:
where can I find twrp for the vibrant I can't seem to find it and it shows as not supported.
Click to expand...
Click to collapse
bro since there's a kernel issue vibrant's twrp doesn't works after flashing this ROM.. So you have to odin back to stock and again do flashing..
BTW i'm kinda surprised to see you bro.. I didn't knew this stuff.. 3 years ago i have seen one of your video on youtube channel.. This would've not happened without that video of yours.. Keep the good work up bro god bless you
thanks man I thought I had lost my old vibrant I found it today and brought it out to play. I had to watch some of my own videos just get back on track lol... I flashed cm 10.1 then resurrection rom 5.0 just to get twrp then flashed omni 5.1 and got it to boot up. I get some many request for more videos that decided to bring the phone back out to try and do some newer updated videos for people that need help.
BTW i'm kinda surprised to see you bro.. I didn't knew this stuff.. 3 years ago i have seen one of your video on youtube channel.. This would've not happened without that video of yours.. Keep the good work up bro god bless you [/QUOTE]
---------- Post added 02-01-2016 at 12:02 AM ---------- Previous post was 01-01-2016 at 11:28 PM ----------
Babloo1989 said:
bro since there's a kernel issue vibrant's twrp doesn't works after flashing this ROM.. So you have to odin back to stock and again do flashing..
BTW i'm kinda surprised to see you bro.. I didn't knew this stuff.. 3 years ago i have seen one of your video on youtube channel.. This would've not happened without that video of yours.. Keep the good work up bro god bless you
Click to expand...
Click to collapse
From your experience which is the most stable 5.1 Rom? I see there's problems with the 6.0.1 omni Rom
djeddieone said:
thanks man I thought I had lost my old vibrant I found it today and brought it out to play. I had to watch some of my own videos just get back on track lol... I flashed cm 10.1 then resurrection rom 5.0 just to get twrp then flashed omni 5.1 and got it to boot up. I get some many request for more videos that decided to bring the phone back out to try and do some newer updated videos for people that need help.
BTW i'm kinda surprised to see you bro.. I didn't knew this stuff.. 3 years ago i have seen one of your video on youtube channel.. This would've not happened without that video of yours.. Keep the good work up bro god bless you
Click to expand...
Click to collapse
---------- Post added 02-01-2016 at 12:02 AM ---------- Previous post was 01-01-2016 at 11:28 PM ----------
From your experience which is the most stable 5.1 Rom? I see there's problems with the 6.0.1 omni Rom[/QUOTE]
bro i suggest CodeROM 5.1.1 it is very stable..
It really whips the lama's ass!
I love this ROM so far.
Problems I've got:
- I'm receiving calls with no sound (fortunately it's a secondary/testing phone).
- The hardware buttons Home and Back are inverted.
- I cannot get the multitasking menu long-pressing any button.
Apart from that, everything look fine.
Congratulations, and thanks for this great port!
thanks I will give it a try can't wait for this 6.0.1 rom to be fully working.
SuperJMN said:
I love this ROM so far.
Problems I've got:
- I'm receiving calls with no sound (fortunately it's a secondary/testing phone).
- The hardware buttons Home and Back are inverted.
- I cannot get the multitasking menu long-pressing any button.
Apart from that, everything look fine.
Congratulations, and thanks for this great port!
Click to expand...
Click to collapse
Im really sorry this problem occurs due to kernel messed up im not able to make complete kernel because im not developer just i know some ways to port do only but ill find the solution quickly and update this rom as soon as possible
djeddieone said:
thanks I will give it a try can't wait for this 6.0.1 rom to be fully working.
Click to expand...
Click to collapse
Hi bro surprised to see you Im also the person who flash the roms by watching your videos link
https://www.youtube.com/watch?v=wMQQDpqVNBk
After that ill watch some information and try porting bro. Ya omni 6.0.1 have many issues due to kernel im not able to get pure kernel but ill try that thaks for your presence
Related
THIS ROM IS STILL IN TESTING STAGE. I DON'T RECOMMEND IT FOR NORMAL USERS OR AS A DAILY DRIVER
Code:
#include <std_disclaimer.h>
/*
* Your warranty is now void.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
What's working -
Almost everything
What's not working -
WiFi- Once turned on, the device goes into bootloop. The only way to come out of it is wipe data from recovery.
Bluetooth- "Bluetooth share has stopped" messages annoy a lot. Just delete Bluetooth from /system/app
Video H/W decoder- Use 3rd party apps like MX Player and use S/W decoder in them
EDIT: You may also try camcorder fix located here
A few more minor ones. Tell me?
Install instructions:
- power off the phone
- reboot to recovery
- full wipe
- flash rom zip
- flash lollipop gapps zip
- reboot
DOWNLOAD:
Links down. Will be uploaded after resolving major issues
Screenshots:
Coming soon...
Source:https://github.com/rhar****/android_device_google_sprout
Thanks to varun.chitre15 for the bring up
Test-1
Added Multiuser support
Documents UI fixed
Added File Manager
Reserved for F.A.Q
Reserved for Thanks
rhar**** said:
Reserved for Thanks
Click to expand...
Click to collapse
Thanks very much bro!! Seems like the way is now not so far for fully stable CM12
Pressed thnx button
YIPPE
thnx ! bro whatsup ! let me test ! soon will post results
for now how to fix wifi
?? help !
first TO write
second to comment !!
In case you haven't noticed, there is already a thread owned by me for the same thing. I don't see any effort in fixing anything which is broken but just a recompiled ROM.
Either way this is not allowed on XDA, i.e taking over something which is already being maintained by someone else without a permission.
I suggest you take down your build and get the thread locked.
varun.chitre15 said:
In case you haven't noticed, there is already a thread owned by me for the same thing. I don't see any effort in fixing anything which is broken but just a recompiled ROM.
Either way this is not allowed on XDA, i.e taking over something which is already being maintained by someone else without a permission.
I suggest you take down your build and get the thread locked.
Click to expand...
Click to collapse
Well, this was expected.
Don't worry, I'll solve this problem. Till then, I have disabled the links
Anyways thnx for compiling
This rom has multiuser too right ?
Sent from my XT1068 using XDA Free mobile app
startracker said:
Anyways thnx for compiling
This rom has multiuser too right ?
Sent from my XT1068 using XDA Free mobile app
Click to expand...
Click to collapse
Yes. This ROM has multiuser too
cm12
please post that link sir.....we r waiting...plz
mahesh.g said:
please post that link sir.....we r waiting...plz
Click to expand...
Click to collapse
Firstly, the link has been updated. Check the first post.
Secondly, don't call me 'sir'
cm12
thank you man....
may i know the roubleshootong procedure for wifi ?
mahesh.g said:
thank you man....
may i know the roubleshootong procedure for wifi ?
Click to expand...
Click to collapse
That's a bug in the ROM.
Wait for next release
cm12 bugs
first booting takes too much time...
after i select country,,going to cynogenmod symbol...after it doesn't boot....
there is bootloop....
android 5.0
hey rocking developer when u r going to post the link (android 5.0 omega rom)
varun.chitre15 said:
In case you haven't noticed, there is already a thread owned by me for the same thing. I don't see any effort in fixing anything which is broken but just a recompiled ROM.
Either way this is not allowed on XDA, i.e taking over something which is already being maintained by someone else without a permission.
I suggest you take down your build and get the thread locked.
Click to expand...
Click to collapse
Actually this is not true. There can be many unofficial CM ROMs in one section. The only issue would be if this ROM uses something of yours without permission which you have not allowed anyone else to use.
Those things would be covered under rule 12.
Other than that we encourage development and developers to work together to make all work better and more stable.
Thanks
FNSM
mahesh.g said:
first booting takes too much time...
after i select country,,going to cynogenmod symbol...after it doesn't boot....
there is bootloop....
Click to expand...
Click to collapse
First Boot Will take Long Time in all Lollipop Builds its due to Default ART Implementation Its Normal
Post ss asap
Devam03 said:
Post ss asap
Click to expand...
Click to collapse
After the next release
This is crDroid for Moto G 4G (Peregrine)
crDroid build will always mainly be based on CyanogenMod with some extra and few features (Cool and useful)
Code:
#include
/*
* Your warranty is now void.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
*/
Code:
IMPORTANT: Make sure you have an unlocked and updated Bootloader
Code:
WORKING
- Everything as in CM
Bugs
- You tell me (With logcats :P)
Code:
CREDITS
CM Rom
Slim Rom
Omni Rom
Many More.....
Kernel
Device tree
XDA:DevDB Information
crDroid, ROM for the Moto G
Contributors
Vatsal
Source Code: https://github.com/crdroidandroid
ROM OS Version: 6.0.x Marshmallow
ROM Kernel: Linux 3.4.x
Based On: CyanogenMod
Version Information
Status: Stable
Created 2015-01-31
Last Updated 2016-02-22
Enjoy to Our Site on Google Plus
Download
Help us with Translations
Donate to Maintain our build server
Demo Video
Download Gapps For Marshmallow
Tried to flash "crdroid-5.0.2-20150131-peregrine.zip" and got the error "Cant open <romname> (bad) Installation aborted"
PS: I think the file was downloaded correctly lol
Sn0wdune said:
Tried to flash "crdroid-5.0.2-20150131-peregrine.zip" and got the error "Cant open <romname> (bad) Installation aborted"
PS: I think the file was downloaded correctly lol
Click to expand...
Click to collapse
i just flashing right now,,and it´s booting ok! btw flashing into "philZ" recovery
:good:
"Don't restore Apps using Titanium Backup!"
Why is that?
mosta00 said:
i just flashing right now,,and it´s booting ok! btw flashing into "philZ" recovery
:good:
Click to expand...
Click to collapse
ohh i miss WI FI conection.. returning to cm
Stuck in boot loop.
Hi
(Moto G 4g, xt1039, europe)
running cwm
Hi I precisely followed the instructions and my device is stuck in a bootloop.
Anyone know how to fix this.
Thanks in advance.
Guys any real issues so far ?!
Boot loop?
one-option said:
Guys any real issues so far ?!
Click to expand...
Click to collapse
..
Thanks
Great ! Flashed for test , everything works fine. boooting normal here
---------- Post added at 03:51 PM ---------- Previous post was at 03:47 PM ----------
To acvoid bootloop you should :
> make a backup
> wipe cache + data + system
> flash crdroid lollipop
> flash gapps for lollipop (don't install kiktat gapps)
> wipe data and factory reset
edt 1: you must use latest twrp or phillz, idk if cwm works
edt 2 : no wi fi connection
---------- Post added at 04:01 PM ---------- Previous post was at 03:51 PM ----------
one-option said:
Guys any real issues so far ?!
Click to expand...
Click to collapse
No wi-fi connection
**** bootloop
ok guys i updated the OP a little bit.
there seems to be a wifi problem which i look into , are there any without wifi problem ?
No bootloop here, but no wifi. Otherwise, I didn't find any problem.
firebird11 said:
ok guys i updated the OP a little bit.
there seems to be a wifi problem which i look into , are there any without wifi problem ?
Click to expand...
Click to collapse
have you fixed it already or we must wait? thanks
Wifi Issues?
Hi, first let me thank you for your work bringing crDroid to pregegrine
Edit: Never mind, I found my answers and think my idea was not applicable.
Hey there,
Wow, very nice and smooth ROM you brought us here,
with a heck of customization and essential custom features already included, just flashed it to take a look, multitasking seems also not to bad in combination with BlueFlame4´s Minfree Fixer app, at least for my taste
Pink kernel works too, feels like a beast with it but, Wifi is simply frozen after first initial boot, it was click-able but after that the button is just "greyed out".
Thanks & Keep this up !
gr3ud said:
Wifi is simply frozen after first initial boot, it was click-able but after that the button is just "greyed out".
Click to expand...
Click to collapse
Does that mean that Wifi works after 2nd boot?
primewell said:
Does that mean that Wifi works after 2nd boot?
Click to expand...
Click to collapse
Unfortunately it does not.
new build
firebird11 said:
new build
Click to expand...
Click to collapse
Flashed your build. Can confirm that WiFi is fixed. Back button is not scaled when changing navbar dpi.
95% FUNCTIONAL 925T PACKAGE
DEODEXED, REMOVED APPS THAT CAN BE DOWNLOADED FROM PLAY STORE. IT HAS @ktoonsez LATEST KERNEL WHICH INCLUDES THE DEEP SLEEP FIX.
I HAVE APM AND NO LOUD MUSIC WARNING WORKING, I'LL UPLOAD THOSE IN A SEPARATE ZIP LATER...ON A CLEAN INSTALL I HAD TO SET THE APN, OTHERWISE EVERYTHING SEEMS TO BE IN WORKING ORDER. NOT ALL THE EDGE FEATURES WORK, OBVIOUSLY THEY DO HAVE DIFFERENT SCREENS. THE CONTACTS DO WORK THOUGH.
DOWNLOAD:
HERE
CREDITS:
@ktoonsez (boot.img)
@ktetreault14 (USED HIS BASE)
Wrong section?
Edit: I'm an idiot, flashed it. Works nicely.
Paradoxumical said:
W̶r̶o̶n̶g̶ ̶s̶e̶c̶t̶i̶o̶n̶?̶
Edit: I'm an idiot, flashed it. Works nicely.
Click to expand...
Click to collapse
HAHA, yea it's for us. I was hoping for more functionality out of the edge features, I haven't really got to mess with it though. Seems like only the contacts works. No FC's or anything though.
Deodexed is a stock rom right? Thanks
Sent from my SM-G920T using XDA Free mobile app
You're all over the place @mikeyinid! Loving the contributions you have made
Thanks! Awesome work. Nice to finally have a rom we can flash.
Is this the 5.1.1 leak? If so I'm all over this
mrapp said:
Is this the 5.1.1 leak? If so I'm all over this
Click to expand...
Click to collapse
It's not, that won't be possible til kernel source drops for 5.1.1. I flashed the 5.1.1 update last night and didn't notice anything that stood out.
mikeyinid said:
It's not, that won't be possible til kernel source drops for 5.1.1. I flashed the 5.1.1 update last night and didn't notice anything that stood out.
Click to expand...
Click to collapse
Fair enough. Mostly after the optimizations to memory management... The effects would probably be only noticed after running it for a few hours
I got 3minit battery working @mocsab :good:
Can u share how u did it?
shooterlgk said:
Can u share how u did it?
Click to expand...
Click to collapse
Some XML and smali edits, I'll post everything up later this evening.
mikeyinid said:
I got 3minit battery working @mocsab :good:
Click to expand...
Click to collapse
That is awesome News - thanks! Did you include it in the new file? Does this new file need to be clean flashed or can I flash over the previous installation?
Thanks again for ALL your had work
mocsab said:
That is awesome News - thanks! Did you include it in the new file? Does this new file need to be clean flashed or can I flash over the previous installation?
Thanks again for ALL your had work
Click to expand...
Click to collapse
Well, it'll be for this ROM, til I have a chance to add it to the other. I'll post a flashable zip later with all the mods.
mikeyinid said:
Well, it'll be for this ROM, til I have a chance to add it to the other. I'll post a flashable zip later with all the mods.
Click to expand...
Click to collapse
sorry it was a dumb question - I didn't realize you created a new rom - your a mad man! and thanks for it -
I will flash and see what it's like -
great work again my friend -thanks for everything! I love having variety - you are helping make the lack of a battery and no SD card palatable!!!
thanks again.
mocsab said:
sorry it was a dumb question - I didn't realize you created a new rom - your a mad man! and thanks for it -
I will flash and see what it's like -
great work again my friend -thanks for everything! I love having variety - you are helping make the lack of a battery and no SD card palatable!!!
thanks again.
Click to expand...
Click to collapse
LOL. I don't think created is the right word. I really didn't do anything but flash some dumb **** on my phone and by some dumb luck have it actually work...
mikeyinid said:
LOL. I don't think created is the right word. I really didn't do anything but flash some dumb **** on my phone and by some dumb luck have it actually work...
Click to expand...
Click to collapse
if all it took was dumb -I would be a genius - you should give yourself much more credit than that - flashing now.
---------- Post added at 03:47 PM ---------- Previous post was at 03:36 PM ----------
Thanks again for this - flash is just completing - and so far so good -
I wonder if you can tell me which features from the EDGE that you included?
By the way - FIVE KIDS? Are you insane! I had two and thought that was more than enough?
Good luck with that - hope the ages are such that the older ones help without putting the younger ones lives in danger - LOL
mocsab said:
if all it took was dumb -I would be a genius - you should give yourself much more credit than that - flashing now.
---------- Post added at 03:47 PM ---------- Previous post was at 03:36 PM ----------
Thanks again for this - flash is just completing - and so far so good -
I wonder if you can tell me which features from the EDGE that you included?
By the way - FIVE KIDS? Are you insane! I had two and thought that was more than enough?
Good luck with that - hope the ages are such that the older ones help without putting the younger ones lives in danger - LOL
Click to expand...
Click to collapse
Try this...
mikeyinid said:
Try this...
Click to expand...
Click to collapse
Downloading will flash shortly -by the way - I don't see 3 minit in the Edge Deodxed roms - I flashed it - all is good -but no 3 minit - do I need to do something to get it working?
EDIT - FLASHED and BOOTED - and there it is! 3 minit battery working - (AWESOME - thank you) and am exploring to see what other special features there might be
Once more = THANKS!
I noticed that KTweaker Ap was not installed witth the rom - was there a reason it was left off? I can grab it from the Ktweaker Kernel zip and flash seperately - but didnt know if you left it out for a reason.
Thank you for the Rom @mikeyinid, seems nice so far. Hey I'm getting a fingerprint sensor error. Is there a fix for this?
Thanks
Code:
#include <std_disclaimer.h>
/*
* Your warranty is now void.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
Working:
Everything
Requirements: You need to be on official Cyanogen OS 12 or CM12.1 (both 64 bit) or Mokee Lollipop (64bit) before flashing this.
Update 14-July-2015
Download: cm-12.1-20150713-r6-UNOFFICIAL-tomato.zip
Notification LED working & dialer issue resolved.
Installation
- Factory Reset (If not on CM-12.1 ROM)
- Flash this ROM using TWRP
- Wipe Dalvik/Cache (Optional)
XDA:DevDB Information
CM12.1 [64bit], ROM for the YU Yureka
Contributors
dumtara
Source Code: https://github.com/CyanogenMod
ROM OS Version: 5.1.x Lollipop
ROM Kernel: Linux 3.10.x
ROM Firmware Required: 64bit CM12s
Based On: CyanogenMod
Version Information
Status: Testing
Created 2015-05-04
Last Updated 2015-07-14
great work bro!!!
:good:
Downloading .....
Till then what's the difference between your ROM and Varun Chitre's ROM, can you define please ?
CM 12 uses ART, then why Dalvik cache wiping???
Now thats the ticket. good going dumtara
---------- Post added at 03:31 PM ---------- Previous post was at 03:31 PM ----------
ujilraj said:
CM 12 uses ART, then why Dalvik cache wiping???
Click to expand...
Click to collapse
Its the same, even if he says or the recovery says wiping dalvik, its actually clearing ART cache
@dumtara
Happy to see u back jst downloaded and flashed the rom. Everything is working smooth and awsome thnks
Sent from my AO5510 using XDA Free mobile app
can this cm12 be ported to zte v5 max ????
I flashed the rom with latest CWM 64bit recovery... I put only one sim (sim1) & Everything went fine on the first boot... Inorder to save battery, i changed my sim to 2G mode from LTE... Rebooted the phone...
On my next boot, com.android.phone keeps crashing asking for sim selection, followed by system ui crash... Basically speaking, i can't use the phone... I've done factory reset, wipe cache, wipe dalvik cache... On first boot again all works fine, but on re-booting, the com.android.phone keeps crashing followed by system ui crash...
What could be the reason? How to fix this issue?
Also i noticed tht, while on com.android.phone error, when i press volume button, the phone soft reboots...
I can't create static wifi under wifi option... It says created but is not shown for connection & so can't be connected.
Xposed Framework for this rom
Hey anyone has installed xposed framework for this rom?...I tried xposed-sdk22-arm-20150501.zip , but that did not work for me...
---------- Post added at 06:37 AM ---------- Previous post was at 06:32 AM ----------
ujilraj said:
I flashed the rom with latest CWM 64bit recovery... I put only one sim (sim1) & Everything went fine on the first boot... Inorder to save battery, i changed my sim to 2G mode from LTE... Rebooted the phone...
On my next boot, com.android.phone keeps crashing asking for sim selection, followed by system ui crash... Basically speaking, i can't use the phone... I've done factory reset, wipe cache, wipe dalvik cache... On first boot again all works fine, but on re-booting, the com.android.phone keeps crashing followed by system ui crash...
What could be the reason? How to fix this issue?
Also i noticed tht, while on com.android.phone error, when i press volume button, the phone soft reboots...
Click to expand...
Click to collapse
restart the phone and after reboot leave the phone 2 minutes..don't open anything for 2 minutes and it will work bro..I have faced the problem..now its works awesome..
Does this ROM requires Gapps to be installed? I installed the 12.1 by varun chitre but i faced some problem. The color enhancement was missing.I didnt find the ususal camera app,rather a bad camera app came.
I downloaded and installed your ROM. But could not get past the initial settings as it is always FCs . Is there anything I am doing wrong?
The steps I followed
1. Wipe - Factory reset. I on on 64 bit TRWP.
2. Removed 2nd SIM during the first boot.(as mentioned in Varun's CM12.1 thread)
Would like to try your build on your reply. I am presently on SOKP R3 released yesterday.
Thanks for your efforts
Update 24-05-2015
Link of updated ROM added at first post.
@dumtara what are the changelogs?? Is it based on latest android version??
Chocklety Boyee said:
@dumtara what are the changelogs?? Is it based on latest android version??
Click to expand...
Click to collapse
https://github.com/CyanogenMod/android/blob/cm-12.1/default.xml
dumtara said:
https://github.com/CyanogenMod/android/blob/cm-12.1/default.xml
Click to expand...
Click to collapse
thanks ...
tamilmad said:
I downloaded and installed your ROM. But could not get past the initial settings as it is always FCs . Is there anything I am doing wrong?
The steps I followed
1. Wipe - Factory reset. I on on 64 bit TRWP.
2. Removed 2nd SIM during the first boot.(as mentioned in Varun's CM12.1 thread)
Would like to try your build on your reply. I am presently on SOKP R3 released yesterday.
Thanks for your efforts
Click to expand...
Click to collapse
I suggest you to flash updated ROM (24-05-2015)
You won't get FC issue.
I think I found my daily driver in this ROM!!!!
dumtara said:
I suggest you to flash updated ROM (24-05-2015)
You won't get FC issue.
Click to expand...
Click to collapse
Thanks for your latest upload. I have installed the same without any problems. I have also used Varun's Thunderzap kernel. My observations...
1. Xposed works beautifully. With Gravity box, total control can be had with this ROM
2. Call volume is adequate.
3. Very smooth. Though I am not a great fan of benchmarks, I got 35460 in Antutu.
4. In the 12 hours of usage, the device heating is minimal in this ROM. hence I do hope that the battery also would be good. I will update on the battery later
I got my Yureka 10 days back. Since then I have been trying various ROMs and kernels available. I think I have found the best daily driver in this ROM and kernel combination. Next choice for me would be SOKP R3.
Great work sir!!!
Thanks
I have Tried Almost All the ROM on my YU, I use to flash Daily Custom Roms which are released, My Favourite One Use To be the Varun.Chettri's Unofficial cm 12.1 Build. BUT After Trying The 3rd Build Of your ROM, I AM UR FAN .... U Defenitely Defeated All Other Developers. Salute :good:
tamilmad said:
Thanks for your latest upload. I have installed the same without any problems. I have also used Varun's Thunderzap kernel. My observations...
1. Xposed works beautifully. With Gravity box, total control can be had with this ROM
2. Call volume is adequate.
3. Very smooth. Though I am not a great fan of benchmarks, I got 35460 in Antutu.
4. In the 12 hours of usage, the device heating is minimal in this ROM. hence I do hope that the battery also would be good. I will update on the battery later
I got my Yureka 10 days back. Since then I have been trying various ROMs and kernels available. I think I have found the best daily driver in this ROM and kernel combination. Next choice for me would be SOKP R3.
Great work sir!!!
Click to expand...
Click to collapse
Your review is indeed very helpful, will be trying this rom soon
---------- Post added at 11:05 AM ---------- Previous post was at 11:04 AM ----------
@dumtara
Kindly do apply for official status for this rom
Code:
/*
* Your warranty is now void.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
*
*/
Hi,
I'm already working over 2 years at the N80XX devices (mostly LineageOS) and want to introduce you my version of Resurrection Remix RR-N-v5.8.5.
For sure I want to thank all guy's which were ever working on these devices and also in general at the smdk4412.
I also want to thank the Resurrection Remix team, LineageOS and so on.
I've added some extra functionality like for example wakening up the device when you pull out the pen, back event when you press the pen button,
fast charging for every power supply, working keyboard dock + lineout functioning, Magisk hide and much more...
Resurrection Remix is a mix out of Omni and LineageOS with many extra features and functionality,
I guess there is no other Rom which offers so many features to customize.
I can't guarantee that there aren't any bugs, so I need you for testing and giving me a feedback.
Spoiler: Not working at the moment:
N8020: incoming calls doesn't pop up, outgoing calls + internet (also LTE) are working fine.
HDMI out for all of them, not implemented.
Spoiler: Links
TWRP
N8000 Rom
N8010 / N8013 Rom
N8020 Rom
Spoiler: Changelog
14.09.2020
24.09.2020
29.09.2020
31.10.2020
30.11.2020
Spoiler: How to install it?
Instructions
To disable the sec_keyboard for example to play games without any hardware keyboard,
simply flash my magisk module to disable it:
sec_keyboard disabler
If you are going to use Gapps,
I recommend to use the pico package!
https://opengapps.org/
How to root the device?
Just simply open Magisk Mangager,
choose install an download zip.
Afterwards reboot to twrp and install the downloaded zip file.
Do you like my work? Than you can simply hit the thanks button and consider to spend me a coffee or a beer,
I'm doing this in my free time and it also costs a lot of money to buy hardware.
donate
XDA:DevDB Information
Resurrection Remix, ROM for the Samsung Galaxy Note 10.1
Contributors
html6405
Source Code: https://github.com/html6405
ROM OS Version: 7.x Nougat
ROM Kernel: Linux 3.10.x
Based On: Resurrection Remix
Last build: 30.10.2020
Security bulletin: 05.10.2020
Selinux: enforcing
Version Information
Status: Stable
Created 2020-07-18
Last Updated 2020-12-16
Well... i have your slim 7 rom already installed...
I'll give it a chance tonight...
(sorry my english)
It works great. And no mouse pointer when I use the SPen.
Charly_Maths said:
It works great. And no mouse pointer when I use the SPen.
Click to expand...
Click to collapse
Thanks, for the size of the rom it's still really fast in my opinion,
not as fast as slim, but very useful.
man, the keyboard is not working
Have I done something wrong?
---------- Post added at 06:36 PM ---------- Previous post was at 06:10 PM ----------
LanguageSoez said:
man, the keyboard is not working
Have I done something wrong?
Click to expand...
Click to collapse
nah! its working. Reflashed and it works
Noob question, but how i can root acces ? for TB, ES file explorer etc
kirucha said:
Noob question, but how i can root acces ? for TB, ES file explorer etc
Click to expand...
Click to collapse
Just open Magisk Manger and choose install, download the zip file and flash it via twrp.
For those people who wants to play games without any hardware keyboard,
just simply flash (with magisk manager or twrp) my new magisk module to disable the sec_keyboard .
You can find the link in the start post.
Which gapps i have to downlod please for arm 7.1 or 7.0 and
Is the wifi works on the n8000 please
@Abela2121 said:
Which gapps i have to downlod please for arm 7.1 or 7.0 and
Is the wifi works on the n8000 please
Click to expand...
Click to collapse
7.1 pico and the wifi works on all of them, I guess about 10% of the fresh installations are facing problems when they try to connect the first time.
Just try it and you will see .
Hey guys I installed the rom 10q HTML dry for my English I mean 10q to the developer and it really amazing
But please I cant install youtube, gmail,chrome from play store when download finished it says can't install this app I use the pico gapps how rto do that please
@Abela2121 said:
Hey guys I installed the rom 10q HTML dry for my English I mean 10q to the developer and it really amazing
But please I cant install youtube, gmail,chrome from play store when download finished it says can't install this app I use the pico gapps how rto do that please
Click to expand...
Click to collapse
Have you installed the rom clean?
Could it be, that you've installed the gapps later without doing a factory reset?
Sometimes this is causing problems.
Yea I forget to reset the device men know there no way to install original YouTube and chrome I have play store working
You could try to wipe the dalvik-cache, but there's no guarantee that this will fix your problem,
just factory reset and start from zero.
OK 10q really
I will try it and i hope it will be fine
Thanks
Working good and fast
But can i enable the cursor of pen showing on the screen
Or should i install spen command ?
Edit :
In one hour the tablet restarted 3 times suddenly.
I dont know whats the problem ?
I did wipe delvik and cash
Thanks
fawzyyyy said:
Working good and fast
But can i enable the cursor of pen showing on the screen
Or should i install spen command ?
Edit :
In one hour the tablet restarted 3 times suddenly.
I dont know whats the problem ?
I did wipe delvik and cash
Thanks
Click to expand...
Click to collapse
Hi,
not at the moment it is not possible to enable the cursor for the pen,
but I will take a look at it.
I've already fixed some small bugs and you will receive a update soon.
RR runs on all my devices stable, but to find out whats going on in your case, just simply create a last_kmsg directly afterwards and send it to me.
Oh? You decided to join XDA to get more Feedback?
I've been using this RR as a daily driver for the last month now and i have to say i prefer it over Slim and Lineage. It's extremely fluid out of the box and doesn't have that laggy feeling Linaeage has.
Give this rom a try if you still use your N8000 guys!
guide me please
html6405 said:
Thanks, for the size of the rom it's still really fast in my opinion,
not as fast as slim, but very useful.
Click to expand...
Click to collapse
hi i am a noob at this and need guidance please, i have a note 10.1 n8010 at the moment its got android 4.4.2 i have not put any custom os or recovery screens but really would like to, i know how to use odin and put tablet in recovery mode but would like a step by step guide on what files i need and what to do please thank you please thank you.
---------- Post added at 02:18 AM ---------- Previous post was at 02:14 AM ----------
hi i am a noob at this and need guidance please, i have a note 10.1 n8010 at the moment its got android 4.4.2 i have not put any custom os or recovery screens but really would like to, i know how to use odin and put tablet in recovery mode but would like a step by step guide on what files i need and what to do please thank you please thank you.
---------- Post added at 02:21 AM ---------- Previous post was at 02:18 AM ----------
hi i am a noob at this and need guidance please, i have a note 10.1 n8010 at the moment its got android 4.4.2 i have not put any custom os or recovery screens but really would like to, i know how to use odin and put tablet in recovery mode but would like a step by step guide on what files i need and what to do please thank you please thank you.