Database Develop

[Guide] Suggested Install Guide for I9300 Omni 4.4 Nightlies

After following the Omni 4.4 Nightlies thread, I thought it would help some people (noobs like me) to have some guidance about how to install Omni in your device and making it easier to get what's needed to make it work. Still, this is not an "official guide", just the procedure I use to flash every day's nightly and I'm open to suggestions and corrections. Also, the resourses quoted here are not my work, just links to the work of the amazing devs in Xda and out there in the Android development world.
Hope it helps. Don't forget to hit "Thanks" in case it was.
Important: be wise and don't go for anything you are not sure about. I can't be held responsible for the results, remember that you are flashing a Custom (Beta stage) ROM, and even when not likely, things can go wrong. If you are unsure about anything, just ask and/or search the forum and the net for other's experience and knowledge, that's the way to go (and learn).
Suggested procedure (updated to November the 30th 2013)
Be sure to check the official thread for lastest news and guidance here.
DOWNLOADS
1) THE RIGHT RECOVERY - Your device must be rooted and running CWM Recovery 6.0.3.2+ or latest TWRP. Latest Philz Recovery is reported to be working too if you prefer. If aren't on CWM/Philz's or not on the right version, you can find a guide to get it and install it here. The safe way to go is to follow any of the procedures listed there. There are also many threads in XDA offering the flashable zip, but if you go down that way, be sure you choose the right version.
2) GET OMNI - Download the latest Omni 4.4 for I9300 Nightly here
3) GET GAPPS - Download the 4.4 Gapps of your choice:
PA Gapps (recommended by XpLoDWilD)
Spec Gapps
Banks Gapps
Any other 4.4 Gapps of your choice (must be 4.4, earlier versions won't work or give you some mean headaches)
4) CUSTOM KERNEL (optional) - If you want to use a custom kernel, download one that you know it's compatible. If you don't know what this means or you are not 100% sure about what you are doing, it would be safer to skip this step. You can explore Xda I9300 forum for info about Custom Kernels if you like.
5) UPDATE SUPERSU - Download the latest Supersu here. Get the Zip to be flashed via CWM. At the moment, the latest can be found here.
INSTALLING
1) If you had to install CWM or Philz, make sure it's done and working.
2) WIPING - Get into recovery. Be sure you make a nandroid backup in case things go wrong. Then, it's time for some wiping. The safer way to go is a Full Wipe, and that means Wiping Data, Cache, and Dalvik. Beware this will result in loosing some user data if you don't got a backup of them (I'd recommend moving anything you want to keep into SD, since Titanium is never a neat choice when flashing a new ROM, you'd probably get your beautiful clean new install dirty if you go that way). Back to wiping, I usually format /system too, just in case.
3) FLASH OMNI - Find and flash the downloaded Omni Build.
4) FLASH GAPPS.
5) FLASH CUSTOM KERNEL (optional) - if you've chosen to do so (should be done before flashing SuperSu Update).
6) FLASH SUPERSU UPDATE.
7) (Optional) Wipe Cache and Dalvik once more. I'm not sure if this is required, just found out it solved some FCs sometimes and since then I do it allways.
8) Reboot.
Post-Installing (Absolutely Optional, but maybe useful)
1) Once you've booted and are past the Gapps Google login and stuff, you might want to install Xposed Framework, in case you use Greenify Pro or just want to access some more customization moduldes. If that's what you want, get the latest 4.4 compatible XPosed Installer APK here and run it. There you need to install the framework and if no errors arise, voilá, you got it. It's reported that you need to set RW privileges to let this happen, if that's the case, you need any root explorer (ES or any other) to do it. And if you aren't able to do so, or still got trouble, you can install BusyBox Installer from the PlayStore, and duh, install it. Or you can just take the advice found here to get that done. Then you'll be able to get /system RW privleges and install Xposed Framework. After doing it, you'll need to reboot, thought.
2) Installing GravityBox or any other Xposed module you want. Gravity is a nice collection of customization options that has been updated recently to support Kitkat. If any others become compatible too, or you want to try any available module to see if it works with 4.4 too, assume the risks and go ahead. Yet, many will become compatible soon, perhaps it would be wiser to wait for that to happen. Back to Gravity, you just need to get it here (make sure to get the last version), install it, enable the Module at Xposed Installer, and reboot.
And that's it. Course you can do plenty of other stuff to your lovely Omni 4.4 Build, but that's up to you. Hope this was of some help and I'm open to any feedback to update the guide and make it better. And in case you spot any mistakes, please let me know. I'm not a dev, just a noob trying to make other noob's life easier.
Enjoy!

Very good guide
Inviato dal mio GT-I9300 utilizzando Tapatalk

Nicely done. Enough info for those who're new to omnirom (like me).
Sent from my GT-I9300 using Tapatalk

Question on Gravitybox. I've installed the Xposed installed, Gravitybox 2.7.6 and ticked on the module, the problem is when Gravitybox opens, it says that Gravitybox System Framework is not responding. What do you think I should do?
fermasia said:
After following the Omni 4.4 Nightlies thread, I thought it would help some people (noobs like me) to have some guidance about how to install Omni in your device and making it easier to get what's needed to make it work. Still, this is not an "official guide", just the procedure I use to flash every day's nightly and I'm open to suggestions and corrections. Also, the resourses quoted here are not my work, just links to the work of the amazing devs in Xda and out there in the Android development world.
Hope it helps. Don't forget to hit "Thanks" in case it was.
Important: be wise and don't go for anything you are not sure about. I can't be held responsible for the results, remember that you are flashing a Custom (Alpha stage) ROM, and even when not likely, things can go wrong. If you are unsure about anything, just ask and/or search the forum and the net for other's experience and knowledge, that's the way to go (and learn).
Suggested procedure (updated to November the 27th 2013)
Be sure to check the official thread for lastest news and guidance here.
DOWNLOADS
1) THE RIGHT RECOVERY - Your device must be rooted and running CWM Recovery 6.0+. Latest Philz Recovery is reported to be working too if you prefer. If aren't on CWM/Philz's or not on the right version, you can find a guide to get it and install it here. The safe way to go is to follow any of the procedures listed there. There are also many threads in XDA offering the flashable zip, but if you go down that way, be sure you choose the right version.
2) GET OMNI - Download the latest Omni 4.4 for I9300 Nightly here
3) GET GAPPS - Download the 4.4 Gapps of your choice:
PA Gapps (recommended by the op)
Spec Gapps
Banks Gapps
Any other 4.4 Gapps of your choice (must be 4.4, earlier versions will likely give you some headaches)
4) CUSTOM KERNEL (optional) - If you want to use a custom kernel, download one that you know it's compatible. If you don't know what this means or you are not 100% sure about what you are doing, it would be safer to skip this step. You can explore Xda I9300 forum for info about Custom Kernels if you like.
5) UPDATE SUPERSU - Download the latest Supersu here. Get the Zip to be flashed via CWM. At the moment, the latest can be found here.
INSTALLING
1) If you had to install CWM or Philz, make sure it's done and working.
2) WIPING - Get into recovery. Now it's time for wiping. The safer way to go is a Full Wipe, and that means Wiping Data, Cache, and Dalvik. Beware this will result in loosing some user data if you don't got a backup of them (I'd recommend moving anything you want to keep into SD, since Titanium is never a neat choice when flashing a new ROM, you'd probably get your beautiful clean new install dirty if you go that way. Back to wiping, I usually format /system too, just in case. Be sure you make a nandroid backup in case things go wrong.
3) FLASH OMNI - Find and flash the downloaded Omni Build.
4) FLASH GAPPS.
5) FLASH CUSTOM KERNEL (optional) - if you've chosen to do so (should be done before flashing SuperSu Update).
6) FLASH SUPERSU UPDATE.
7) (Optional) Wipe Cache and Dalvik once more. I'm not sure if this is required, just found out it solved some FCs sometimes and since then I do it allways.
8) Reboot.
Post-Installing (Absolutely Optional, but maybe useful)
1) Once you've booted and are past the Gapps Google login and stuff, you might want to install Xposed Framework, in case you use Greenify Pro or just want to access some more customization moduldes. If that's what you want, get the latest 4.4 compatible XPosed Installer APK here and run it. There you need to install the framework and if no errors arise, voilá, you got it. It's reported that you need to set RW privileges to let this happen, if that's the case, you need any root explorer (ES or any other) to do it. And if you aren't able to do so, or still got trouble, you can install BusyBox Installer from the PlayStore, and duh, install it. Or you can just take the advice found here to get that done. Then you'll be able to get /system RW privleges and install Xposed Framework. After doing it, you'll need to reboot, thought.
2) Installing GravityBox or any other Xposed module you want. Gravity is a nice collection of customization options that has been updated recently to support Kitkat. If any others become compatible too, or you want to try any available module to see if it works with 4.4 too, assume the risks and go ahead. Yet, many will become compatible soon, perhaps it would be wiser to wait for that to happen. Back to Gravity, you just need to get it at the PlayStore, install it, enable the Module at Xposed Installer, and reboot.
And that's it. Course you can do plenty of other stuff to your lovely Omni 4.4 Build, but that's up to you. Hope this was of some help and I'm open to any feedback to update the guide and make it better. And in case you spot any mistakes, please let me know. I'm not a dev, just a noob trying to make other noob's life easier.
Enjoy!
Click to expand...
Click to collapse

carlallanvela said:
Question on Gravitybox. I've installed the Xposed installed, Gravitybox 2.7.6 and ticked on the module, the problem is when Gravitybox opens, it says that Gravitybox System Framework is not responding. What do you think I should do?
Click to expand...
Click to collapse
Should I assume you: got an i9300, installed following the procedure, did all the wipes, are on the latest (27th) nightly, got the right Xposed Framework installed successfully with no errors, rebooted, installed gravity last version (2.7.6), enabled the gravity module, rebooted again? If so, and can't live without Gravity till next nightly, I'm not sure what else to suggest but reinstall from scratch and try again.

I got it. Looks like I used Xposed Firmware not Installer. Got it working.
fermasia said:
Should I assume you: got an i9300, installed following the procedure, did all the wipes, are on the latest (27th) nightly, got the right Xposed Framework installed successfully with no errors, rebooted, installed gravity last version (2.7.6), enabled the gravity module, rebooted again? If so, and can't live without Gravity till next nightly, I'm not sure what else to suggest but reinstall from scratch and try again.
Click to expand...
Click to collapse

carlallanvela said:
I got it. Looks like I used Xposed Firmware not Installer. Got it working.
Click to expand...
Click to collapse
Cheers :good:

fermasia said:
Cheers :good:
Click to expand...
Click to collapse
This is brilliant. Maybe add the list of known bugs and as they are fixed, you can cross them out, Would definately keep the main thread cleaner. Well done :good:

cornelha said:
This is brilliant. Maybe add the list of known bugs and as they are fixed, you can cross them out, Would definately keep the main thread cleaner. Well done :good:
Click to expand...
Click to collapse
Would be very interesting, but I guess it would be a bit tricky to keep up with known issues and resolution, unless there's somewhere I can check for that information. I guess that would be in the better hands of the devs that are after bugs and solutions on a daily basis. But still, if there's any way I can help keep track and inform about that, I'd be happy to help.

fermasia said:
Would be very interesting, but I guess it would be a bit tricky to keep up with known issues and resolution, unless there's somewhere I can check for that information. I guess that would be in the better hands of the devs that are after bugs and solutions on a daily basis. But still, if there's any way I can help keep track and inform about that, I'd be happy to help.
Click to expand...
Click to collapse
It's all over the Omni Thread. The devs are way too busy building the rom and sorting out bugs. The most common ones relate to Google Services battery drain. Camera issues and root.

cornelha said:
It's all over the Omni Thread. The devs are way too busy building the rom and sorting out bugs. The most common ones relate to Google Services battery drain. Camera issues and root.
Click to expand...
Click to collapse
I'll try to build a list of those, but I believe it wouldn't be serious to post it if not very precise and up-to-date. Think it's a great idea, but again, not having access to de development roadmap, is a big drawback, and I wouldn't want to go around pushing confusing info.

Problems with Root
After I flashed the 15Dec Build, suddenly I found I'm having problems with Root.
I'm flashing SuperSU 1.75 and RootChecker won't finish.
Xposed Framework won't install, etc.
I've trued the RW trick mentioned above but never get a response to 'su'.
Root worked fine prior to this build.
Any easy fix?

harrybarracuda said:
After I flashed the 15Dec Build, suddenly I found I'm having problems with Root.
I'm flashing SuperSU 1.75 and RootChecker won't finish.
Xposed Framework won't install, etc.
I've trued the RW trick mentioned above but never get a response to 'su'.
Root worked fine prior to this build.
Any easy fix?
Click to expand...
Click to collapse
You've got the wrong SuperSU version. See that the guide redirects you to Chainfire's SuperSU Xda thread, and there you'll find the latest recovery flash version is 1.86 and that's the one you want to grab. If not, download it from the Store, then update binaries by recovery, and there you are. For sure, if you want to try to do this procedure the dirty way, see if it works, if not, you should reinstall Omni with full wipes and use the new supersu version. Let me know if you got it solved or we will try to help you out with your problem.

XPOSED Framework Install - Galaxy S4 SCH-I545 (OF1) Flashfire

I've been reading thousands of forum entries on how to install the xposed framework for my device and I can't seem to get it. They all end the same way -- stuck at the Verizon logo screen.
I am using a Verizon Samsung Galaxy S4 on stock Lollipop (5.0.1). I only have the stock bootloader thanks to it being locked before I laid hands on the device, but I do have Flashfire, Root, SuperSU. Each time I fail, I use ODIN to flash I545VRUGOF1_I545VZWGOF1_I545VRUGOF1_HOME.tar and try again.
I have tried using a deodexed rom by flashing the above with ODIN, then using Flashfire to OTA update: I545_OF1_Stock_Rooted_Deodexed_ROM.zip
Next, install the XposedInstaller_3.0_alpha4.apk
I then tried flashing:
xposed-v71-sdk21-arm-arter97-V6-snapdragon
xposed-v75-sdk21-arm-arter97-snapdragon
xposed-v86-sdk21-arm
They all result in freezing on the Verizon logo during boot.
I can flash xposed-sdk21-arm-20150430-arter97 on to the deodexed rom and it will work, but the Xposed Installer says it's not the most recent and all modules yield the same error:
This module requires a newer XposedBridge version (30) and thus cannot be activated.
Then I try with the stock rom (odexed).
I can flash:
xposed-v71-sdk21-arm-arter97-V6-snapdragon
xposed-v75-sdk21-arm-arter97-snapdragon
xposed-v86-sdk21-arm
Without a crash; So long as the XposedInstaller_3.0_alpha4.apk is not installed. If I install the XposedInstaller then try to flash, it hangs on the Verizon logo during boot.
Finally, if I flash the zips first, then reboot and install the XposedInstaller it will yield me the same result of not the most recent version and I get the requires newer bridge for all modules.
Because it's an S4 there are hundreds of forums and guides, but I can't find one that applies to me. That makes me either the worst internet researcher in the world -- or I'm missing something so obvious that it's embarrassing...well, humiliating.
Can anyone offer a suggestion? ...and yes, I've read every read only forum to the last line and every XDA Lollipop forum. I've reflashed my phone almost two dozen times trying different suggestions with absolutely no luck.

I was having similar issues trying to get xposed on 5.0.1.
Long story short I gave up and flashed 5.1.1 onto my Note 4 and used wanam's custom xposed framework.

Galaxy S4
I don't believe there is a stock 5.1 firmware for the Galaxy S4. More importantly, I have to believe you can install Xposed on the S4. I just hate feeling like I'm missing something so simple!!

DemoMatrix said:
I don't believe there is a stock 5.1 firmware for the Galaxy S4. More importantly, I have to believe you can install Xposed on the S4. I just hate feeling like I'm missing something so simple!!
Click to expand...
Click to collapse
I have a i545 with locked boot loader I used flashfire to flash XposedInstaller_3.0_alpha4 and xposed-v85.0-samsung-5.0.x-sdk21-test-by-dkcldark.zip and it has been working fine for me, I thought my phone was froze on the Verizon splash screen on the first restart so I pulled the battery and tried starting the phone again and it started like normal

krusherkills123 said:
I have a i545 with locked boot loader I used flashfire to flash XposedInstaller_3.0_alpha4 and xposed-v85.0-samsung-5.0.x-sdk21-test-by-dkcldark.zip and it has been working fine for me, I thought my phone was froze on the Verizon splash screen on the first restart so I pulled the battery and tried starting the phone again and it started like normal
Click to expand...
Click to collapse
I think I might love you.
I haven't seen that v85 file anywhere. I'm going to go search for it now. Thank you!

krusherkills123 said:
I have a i545 with locked boot loader I used flashfire to flash XposedInstaller_3.0_alpha4 and xposed-v85.0-samsung-5.0.x-sdk21-test-by-dkcldark.zip and it has been working fine for me, I thought my phone was froze on the Verizon splash screen on the first restart so I pulled the battery and tried starting the phone again and it started like normal
Click to expand...
Click to collapse
That went faster than I expected. Going to give it a flash now.

Well, thank you for the effort.
It flashed very quickly and then rebooted without a problem, but the Xposed Installer still shows, "The Xposed framework is not installed. Please download the latest ZIP file from XDA and flash it manually via recovery." and all the modules say, "..requires a newer XposedBridge version (30) and thus cannot be activated".
I don't suppose you'd be willing to use FlashFire to make a full backup (minus your cache, of course) to share?

Well, thank you for the effort.
It flashed very quickly and then rebooted without a problem, but the Xposed Installer still shows, "The Xposed framework is not installed. Please download the latest ZIP file from XDA and flash it manually via recovery." and all the modules say, "..requires a newer XposedBridge version (30) and thus cannot be activated".
I don't suppose you'd be willing to use FlashFire to make a full backup (minus your cache, of course) to share?

UR 31337
krusherkills123 said:
I have a i545 with locked boot loader I used flashfire to flash XposedInstaller_3.0_alpha4 and xposed-v85.0-samsung-5.0.x-sdk21-test-by-dkcldark.zip and it has been working fine for me, I thought my phone was froze on the Verizon splash screen on the first restart so I pulled the battery and tried starting the phone again and it started like normal
Click to expand...
Click to collapse
Thank you! I uninstalled Xposed Installer and rebooted. Reinstalled Xposed Installer, rebooted, then flashed the file again. Upon that reboot it did the, "Upgraded file xx of xx" and now it's installed!
I can't thank you enough!

View attachment xposed-v65-sdk21-arm-arter97-V5-krait.zip
View attachment de.robv.android.xposed.installer_v33_36570c-1.apk
The Wanam Module is the only thing that I've used.

DemoMatrix said:
Thank you! I uninstalled Xposed Installer and rebooted. Reinstalled Xposed Installer, rebooted, then flashed the file again. Upon that reboot it did the, "Upgraded file xx of xx" and now it's installed!
I can't thank you enough!
Click to expand...
Click to collapse
I am in same boat do you think this very would work if I have the strang5litre rom on the s4. Or would I need another ver. What rom did you have when you got this to work the stick one?
---------- Post added at 11:18 PM ---------- Previous post was at 11:15 PM ----------
trulosdoulos said:
I am in same boat do you think this very would work if I have the strang5litre rom on the s4. Or would I need another ver. What rom did you have when you got this to work the stick one?
Click to expand...
Click to collapse
Stock one* I meant

I'm using the stock rom, jfltvzw, 5.0.1

I'm on stang5litre. I'm surprised you got it to work on stock.

Details
DemoMatrix said:
I'm using the stock rom, jfltvzw, 5.0.1
Click to expand...
Click to collapse
Could you provide the steps you used to achieve this? Thanks!

Please explain how to do this.
Hello.
Can anyone explain the steps to install Xposed framework on the Samsung Galaxy S4 SCH-i545, rooted with stock ROM 5.0.1? I found and downloaded the two files noted in krusherkills123's post, but Flashfire only shows the XposedInstaller_3.0_alpha4 under "Flash firmware package" where it brings up a blank "Partitions" screen and no options.
I used Flashfire to flash the other file, xposed-v85.0-samsung-5.0.x-sdk21-test-by-dkcldark.zip, which I hated to do since I have no idea what it actually does. Since I don't know what it does, I can't confirm that flashing it was successful.
Any help would be appreciated.

Same question here, rooted Verizon S4 I545VRSGPL1, can I install xposed? This is stock rom, rooted with kingroot then cleaned to use SuperSU
People have done with OF1, not sure about PL1, but they are not far apart
Thx!

Pokemon GO 0.37+ : which ROM ?

Hello there,
stupid question but Pokemon Go doesn't work with latest version (0.37). It says OS is incompatible (and ROM has been de-rooted, this was verified). I think it's due to Safeynet check that doesn't pass. I will check this tonight !
Using an old AMCHA version (Android 4.4.4), Pokemon Go works great with 0.35... but for now. When this version will be desactived, there will be no way to play anymore.
Is there a ROM, official or custom, working with Pokemon Go 0.37 and future versions ?
Thanks for your help !

seconding this!
i am on N4EliteLite_v15-Final-Note5Edition_i9305_AROMA and the game worked perfectly until the update
i already tried RootCloack with Xposed -- not working
i cannot try magisk method because it requires android 5.0 and i have not found a 5.0 rom with working gps for i9305.
any ideas?
thanks in advance!

Yep, I saw Magisk method but I didn't noticed it was only for Android 5.0+. So I will have to flash a new ROM if I want Pokemon GO + root !
Is there an official Samsung release (or an optimised ROM based on it) that works will v0.37 ?
@Girugamesh : it seems that Ressurection Remix is the best one to choose !

thanks for telling.
unfortunaly i am stuck with magisk manager root toggle turning it self off again
i flashed ressurection remix and followed the guide on androidpolice
i even tried flashing "unSU Script zip"
let me hear if you have any luck with your i9305

I will try to flash new ROM this week-end. I will tell you if I find something.
For your issue, check if all the folders associated with SuperSU are deleted : /system/xbin/su, /data/su.img, /sbin/su etc. There is probably something remaining from previous root.

i finaly made it. the real pain was to get rid of a corrupted supersu installation (es file explorer was not allowed to remove su.bin)
i did supersu unroot, deleted the files you said, also used unSu script.zip BUT since i dont need root, i just started pokemon and it works.
to clarify i am on ressurection remix android6.0 with a i9305
thanks for your help

Great news !
For my wife's phone, I will give a try on the latest official ROM (4.4.4 - I9035XXUFPB1). If it doesn't work, I will go on RRM + full unroot. More news this week-end

hoeni said:
How?
I didn't find a Superuser app, but I deleted everything su related from /system
Flashed magisk, Flashed phh Superuser, installed magisk and phh app, but the toggle keeps reverting to root. Maybe you could provide me with the steps you took
Click to expand...
Click to collapse
I thought that I'd post my solution here. I'm running CM13 right now and I can run the lastest version of Pokemon go.
1. Install Supersu from the play store and select the option full unroot.
2. Flash Magisk and phh's SuperUser.
3. Install the Magisk manager apk and install phh's SuperUser from the play store.
4. Now when you want to play PoGo open the Magisk manager and disable root. Simple as that.

JD. A said:
I thought that I'd post my solution here. I'm running CM13 right now and I can run the lastest version of Pokemon go.
1. Install Supersu from the play store and select the option full unroot.
2. Flash Magisk and phh's SuperUser.
3. Install the Magisk manager apk and install phh's SuperUser from the play store.
4. Now when you want to play PoGo open the Magisk manager and disable root. Simple as that.
Click to expand...
Click to collapse
Yep, I followed the steps provided by the dev of magisk. Seems like that thread gets so overrun by "doesn't work" that individual questions get forgotten haha
I can't think of anything I did wrong, I'm trying to get it to work on an s3 lte and a note 3.
On my main, s7 edge, it works perfectly. But only because I found a rom featuring magisk and phh root in aroma.
I'm reflash the rom right now to start over. Maybe it'll work now.
Edit:
phh's root didn't work.
the modified SU app did however
Edit 2:
Nah
Magisk is working, yes, but PoGo wont let me enter and SafetyNet wont let me pass either.
Ugh getting sick of this.

Tested with official I9305XXUFOB2 and without any root / busybox, everything is OK with Pokemon GO 0.37.1. No need to go further for my part

Lwysiwyg said:
Tested with official I9305XXUFOB2 and without any root / busybox, everything is OK with Pokemon GO 0.37.1. No need to go further for my part
Click to expand...
Click to collapse
damn, it could have been so easy.. good job mate :good:
i will remember this.
EDIT: install stock , unroot with supersu , even pokemon go v0.41.4 works now

Girugamesh said:
damn, it could have been so easy.. good job mate :good:
i will remember this.
EDIT: install stock , unroot with supersu , even pokemon go v0.41.4 works now
Click to expand...
Click to collapse
Hey man, can you help me step by step what you did to unroot and get POGO running on resurrection remix

Can't install Xposed

Hey everyone.
I can't install the Xposed framework. The error messages are in the the screenshots you'll see attached.
(EDIT: I can't post outside links since i am a new user, also i am by this Time unable to upload screenshots.. i'm working on it.)
de(DOT)tinypic(DOT)com/r/2cx89yd/9
de(DOT)tinypic(DOT)com/r/14ufkvo/9
I am currently using an OnePlus 3 with oxygenOS 3.26 flashed via twrp.
Before I was using 3.24 where everything was working fine. Then I switched to sultanxda's CyanogenMod. Since the Home Button was not working correctly, I decided to go back to the just released Oxygen. Everytime I was clean installing it.
From there on I am unable to use Xposed. I flashed it many times, used different twrp versions and also the arm64 v85 instead of v86. Nothing really wants to work.
I thought, i am may not able to flash anything because the System is set to Read-Only, but flashing SuperUser.zip has worked without any problems.
I'll appreciate your help.

P0ttiBoo said:
Hey everyone.
I can't install the Xposed framework. The error messages are in the the screenshots you'll see attached.
(EDIT: I can't post outside links since i am a new user, also i am by this Time unable to upload screenshots.. i'm working on it.)
de(DOT)tinypic(DOT)com/r/2cx89yd/9
de(DOT)tinypic(DOT)com/r/14ufkvo/9
I am currently using an OnePlus 3 with oxygenOS 3.26 flashed via twrp.
Before I was using 3.24 where everything was working fine. Then I switched to sultanxda's CyanogenMod. Since the Home Button was not working correctly, I decided to go back to the just released Oxygen. Everytime I was clean installing it.
From there on I am unable to use Xposed. I flashed it many times, used different twrp versions and also the arm64 v85 instead of v86. Nothing really wants to work.
I thought, i am may not able to flash anything because the System is set to Read-Only, but flashing SuperUser.zip has worked without any problems.
I'll appreciate your help.
Click to expand...
Click to collapse
Please use the corresponding Xposed thread or OP3 forum for your issue.

Magisk V16 can't install on Android 5.0

Has anyone has success in installing this on Android 5.0 samsung S4 ? I followed the instructions and the manager just says not installed.

Unless you provide more details and installation logs it's gonna be hard to help...

Didgeridoohan said:
Unless you provide more details and installation logs it's gonna be hard to help...
Click to expand...
Click to collapse
What details would you like to know? I flash it and then later restart but the manager was not there so I tried to install it from saving the apk file that I downloaded. But it just said it was not installed and later I found out I lost root from trying to flash Xposed on my phone.
I am very new to this and tried to follow the tutorials and videos but its not working cause I thought using Magisk I can install the seamless Xposed.

Those recovery/installation logs would be a good start.
You're muddling up the details a bit...
Was the Manager not installed or did it report that Magisk wasn't installed? And you lost root? But you said you couldn't install Magisk... Are you already rooted? That might cause issues.
Being nice and clear and detailed (what is being flashed, version numbers, what's already done, what works, what doesn't work, with logs, etc) in your descriptions would help.

Didgeridoohan said:
Those recovery/installation logs would be a good start.
You're muddling up the details a bit...
Was the Manager not installed or did it report that Magisk wasn't installed? And you lost root? But you said you couldn't install Magisk... Are you already rooted? That might cause issues.
Being nice and clear and detailed (what is being flashed, version numbers, what's already done, what works, what doesn't work, with logs, etc) in your descriptions would help.
Click to expand...
Click to collapse
I hope this is clearly for you!
1. I flash the file with TWRP with success
2. The phone got stuck on samsung logo
3. Root was removed.
4.I had to re flash stock and it is working again.
5. How do I get the logs of Magisk if my phone keeps looping?
I wanted to use Magisk to see if Xposed would work but it looks like i can't even get Magisk to work on my samsung i9500 with original rom. This same thing happens with Xposed where everything goes smoothly with flashing it in recovery and then a boot loop on the logo. Others on this forum have been complaining about this too and perhaps the developer might have not considered odexed rom like samsung for these wonderful apps to work?
I am going back to Kitkat where i don't have these issues and I can use Xposed.