Unable to flash custom recovery on Marshmallow - X 2014 Q&A, Help & Troubleshooting

Hi. I'm on Marshmallow and whenever I try to install recovery via fastboot, I go down to recovery and boot it, but it always goes to the battery charging logo and reboots.
Any ideas on how to solve this?
Thanks!

Sesamechicken said:
Hi. I'm on Marshmallow and whenever I try to install recovery via fastboot, I go down to recovery and boot it, but it always goes to the battery charging logo and reboots.
Any ideas on how to solve this?
Thanks!
Click to expand...
Click to collapse
Is your bootloader unlocked?
Are you flashing recovery like this:
fastboot flash recovery twrp-3.0.2-1-victara.img
Then booting into recovery right away?

Yes my bootloader is unlocked and yes that's exactly how I flash it (except I named it recovery)
And yes, I boot into recovery right away via the bootloader options.

Gus Ghanem said:
Is your bootloader unlocked?
Are you flashing recovery like this:
fastboot flash recovery twrp-3.0.2-1-victara.img
Then booting into recovery right away?
Click to expand...
Click to collapse
Forgot to quote sorry

Sesamechicken said:
Yes my bootloader is unlocked and yes that's exactly how I flash it (except I named it recovery)
And yes, I boot into recovery right away via the bootloader options.
Click to expand...
Click to collapse
What is the phone booting into? Stock?
If you have the latest stock firmware files, try:
fastboot flash partition gpt.bin
fastboot flash motoboot motoboot.img
fastboot flash recovery recovery.img
Only use TWRP or Cyanogen Recovery, they are the only ones supported.

Gus Ghanem said:
What is the phone booting into? Stock?
If you have the latest stock firmware files, try:
fastboot flash partition gpt.bin
fastboot flash motoboot motoboot.img
fastboot flash recovery recovery.img
Only use TWRP or Cyanogen Recovery, they are the only ones supported.
Click to expand...
Click to collapse
OK I will try that. Stock marshmallow right?
I was on complete stock and used windroid to unlock bootloader and I was aware of the problem whilst installing custom recovery.
Am I able to flash SuperSU via flash boot since that's mainly what I'm looking for?
Thanks
Sent from my XT1095 using XDA-Developers mobile app

Sesamechicken said:
OK I will try that. Stock marshmallow right?
I was on complete stock and used windroid to unlock bootloader and I was aware of the problem whilst installing custom recovery.
Am I able to flash SuperSU via flash boot since that's mainly what I'm looking for?
Thanks
Sent from my XT1095 using XDA-Developers mobile app
Click to expand...
Click to collapse
Make sure you never downgrade the bootloader or partition table, so yes, use the latest Android 6.0 MarshMallow firmware, in case something gets corrupted and you need to reflash the partition table and/or bootloader, or even the full stock firmware, so you can start again.
Flashing SuperSU is always risky, and I've never done it; I only use CM's built-in Root Access.

Gus Ghanem said:
Make sure you never downgrade the bootloader or partition table, so yes, use the latest Android 6.0 MarshMallow firmware, in case something gets corrupted and you need to reflash the partition table and/or bootloader, or even the full stock firmware, so you can start again.
Flashing SuperSU is always risky, and I've never done it; I only use CM's built-in Root Access.
Click to expand...
Click to collapse
Just tried that to no avail.
Is there anyway to root without having a custom recovery?

Sesamechicken said:
Just tried that to no avail.
Is there anyway to root without having a custom recovery?
Click to expand...
Click to collapse
I really don't know, as I only have the one phone, and don't want to take any risks with, I never looked into rooting, and never needed it anyway. But if I ever need the odd root access, CyanogenMod does it for me.
There are apps like King Root, which I've never used:
https://kingroot.net/
TRY AT YOUR OWN RISK.

Gus Ghanem said:
I really don't know, as I only have the one phone, and don't want to take any risks with, I never looked into rooting, and never needed it anyway. But if I ever need the odd root access, CyanogenMod does it for me.
There are apps like King Root, which I've never used:
https://kingroot.net/
TRY AT YOUR OWN RISK.
Click to expand...
Click to collapse
Ok, so I tried the Kingroot method and it took out my wifi and cellular network (doesn't turn on).
So I flashed the system files in the marshmallow and now my system doesn't boot. xD!
One question: is there any single marshmallow system zip file I could flash in one go to increase chances of resurrection? What's annoying is that I can't seem to get custom recovery working.
Thanks

Gus Ghanem said:
I really don't know, as I only have the one phone, and don't want to take any risks with, I never looked into rooting, and never needed it anyway. But if I ever need the odd root access, CyanogenMod does it for me.
There are apps like King Root, which I've never used:
https://kingroot.net/
TRY AT YOUR OWN RISK.
Click to expand...
Click to collapse
Nevermind! I am so f****ng stupid!!!!
I NEVER ACTUALLY SELECTED USING UP VOLUME I ALWAYS CLICKED THE POWER BUTTON WHICH REBOOTED. I AM ACTUALLY SO STUPID.
Thanks anyways!

Sesamechicken said:
Ok, so I tried the Kingroot method and it took out my wifi and cellular network (doesn't turn on).
So I flashed the system files in the marshmallow and now my system doesn't boot. xD!
One question: is there any single marshmallow system zip file I could flash in one go to increase chances of resurrection? What's annoying is that I can't seem to get custom recovery working.
Thanks
Click to expand...
Click to collapse
Since we don't know for sure what's causing it not to boot, might as well flash the whole fimware, I think you can paste all the commands at once, or create a batch file in the firmware folder, flash.bat, shift+right-click, open command window here... type flash.bat
Or you can use RSD Lite
If/when you lose signal/data/wifi you can try flashing just the modems from stock:
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn

Related

[Q] I done screwed up big time - the mystery of the unflashable recovery

Back story: Verizon Moto X, unlocked bootloader via China Middleman, running Eclipse ROM 4.4.2, TWRP 2.7.0.0 recovery
Objective: wipe everything and flash back to a (rooted) stock for device retail
Why I'm screwed: everything is wiped - phone has no OS, recovery, etc. It simply hangs out on the Motorola M at boot and doesn't move. fastboot loads and will flash recovery (seemingly successfully) but rebooting to recovery always gets stuck at the logo
How I got there:
1. Backed up with TWRP, then flashed new recovery CWM (the one here) and backed up again. Saved both folders of nandroid backups to my PC (yay)
2. Flashed back to TWRP (but this time the new one v2.8.0.1 here, which I downloaded and flashed via that fancy new TWRP app [I selected the "ghost" model]) clicked about every type of wipe option I could get my grubby little fingers on, then adb pushed the ROM and kernel/radio combo from here.
3. Attempted to flash the new ROM via TWRP. It failed. something about an "Error executing updater binary in zip". I sighed, said "meh", googled the problem a bit and figured I'd reboot the recovery and try again. This is where things get weird.
4. Phone hangs out at boot logo (that kaleidoscope "M"). Fine, I accidentally did a normal boot, and there's no OS installed. I go into fastboot and boot to recovery. SAME SCREEN. TWRP has apparently disappeared. No matter. I go into fastboot and flash it again, then boot to recovery. SAME SCREEN. Flash back to CWM. SAME SCREEN. Back to TWRP one more time just for giggles? SAME SCREEN.
No idea where to go from here. Anyone have any idea how this happened and what my options are at this point? Is there a way to manually flash a ROM via fastboot? Restore either my CWM or TWRP nandroid backups without access to the recovery? Any guidance would be appreciated.
Attachments:
a) boot logo I'm stuck on
b) command line log of commands from flashing recoveries
From fastboot, flash your recovery and then use the volume down button to highlight recovery and then volume up button to enter into recovery.
VerneVerne said:
From fastboot, flash your recovery and then use the volume down button to highlight recovery and then volume up button to enter into recovery.
Click to expand...
Click to collapse
Perhaps I didn't make that clear - that's exactly what I've been doing.
PHP:
gerodive said:
Back story: Verizon Moto X, unlocked bootloader via China Middleman
Click to expand...
Click to collapse
That is what I have.
gerodive said:
No idea where to go from here. Anyone have any idea how this happened and what my options are at this point? Is there a way to manually flash a ROM via fastboot?
Click to expand...
Click to collapse
Well I wiped my system partition when I must have been drunk or something b/c I still can't believe I did it. But I did. Then from bootloader mode, I ran the command mfastboot flash system system.img from a command shell on my PC using the system image from the sbf that my bootloader was currently on (in my case, it was 4.4.4). All was good.
Then I could restore my nandroids by moving them to my phone from my PC.
Wansanta said:
PHP:
That is what I have.
Well I wiped my system partition when I must have been drunk or something b/c I still can't believe I did it. But I did. Then from bootloader mode, I ran the command mfastboot flash system system.img from a command shell on my PC using the system image from the sbf that my bootloader was currently on (in my case, it was 4.4.4). All was good.
Then I could restore my nandroids by moving them to my phone from my PC.
Click to expand...
Click to collapse
Could you elaborate a little more on this? How do I get the system.img file to flash? I'm guessing my bootloader would be on the 4.4.2 one since that was what Eclipse was on, but is there any way to check? Deleting the system partition was definitely what I did. Also, why mfastboot as opposed to just fastboot?
gerodive said:
Could you elaborate a little more on this? How do I get the system.img file to flash?
Click to expand...
Click to collapse
mfastboot flash system system.img
gerodive said:
I'm guessing my bootloader would be on the 4.4.2 one since that was what Eclipse was on, but is there any way to check?
Click to expand...
Click to collapse
In bootloader mode it will tell you on the second line. 30:B7 is the 4.4.4 bootloader version.
gerodive said:
Deleting the system partition was definitely what I did.
Click to expand...
Click to collapse
As long as you can get into bootloader mode you can flash it back.
gerodive said:
Also, why mfastboot as opposed to just fastboot?
Click to expand...
Click to collapse
because the moto x system images are too large to flash with fastboot, you have to use mfastboot.
gerodive said:
Back story: Verizon Moto X, unlocked bootloader via China Middleman, running Eclipse ROM 4.2.2, TWRP 2.7.0.0 recovery
Click to expand...
Click to collapse
gerodive said:
I'm guessing my bootloader would be on the 4.4.2 one since that was what Eclipse was on, but is there any way to check?
Click to expand...
Click to collapse
4.2.2 or 4.4.2?
nhizzat said:
4.2.2 or 4.4.2?
Click to expand...
Click to collapse
yeah he really needs to check b/c it really matters what version of the bootloader he is on.
Flashing the 4.4.2 system.img (and boot.img just for good measure) worked! I was then able to boot normally and then upgraded to 4.4.4. Oh happy day. Thanks for the help everyone.
Sorry, meant 4.4.2.
gerodive said:
Flashing the 4.4.2 system.img (and boot.img just for good measure) worked! I was then able to boot normally and then upgraded to 4.4.4. Oh happy day. Thanks for the help everyone.
Click to expand...
Click to collapse
So glad!! If you are unlocked, as long as you can get into a functioning bootloader mode and have access to the sbf for your version of the OS you haven't bricked.
I about near had a heart attack when I deleted my system, but no biggie to restore it. I think I only paid $35 to unlock b/c I did it straight through tao bao, but it was the best $35 I have spent in a long time. I drop $35 every time I go for sushi, so I can't imagine not paying to unlock if you have the option.

[Q] Error while installing 5.0.1 update

Hi I just got the 5.0.1 update, I downloaded it and the phone rebooted itself, I got the installation screen and after 5 seconds I just got the word "error" and I had to restart it manually; the device is rooted, have anyone else had this problem? I would appreciate your help
saman0suke1 said:
Hi I just got the 5.0.1 update, I downloaded it and the phone rebooted itself, I got the installation screen and after 5 seconds I just got the word "error" and I had to restart it manually; the device is rooted, have anyone else had this problem? I would appreciate your help
Click to expand...
Click to collapse
With lollipop you can't take an OTA if you are rooted or running just about anything else modified (custom kernels, like ones that have force decrypt disabled also will cause it to error out).
You can still flash it manually by flashing the images. If you don't want to wipe, don't flash the userdata.img . Also, if you aren't currently encrypted, booting up with the stock kernel will force encrypt your device, so don't flash that if you want to stay that way. You can then re-root. There are more in depth instructions for doing this out there if you search around for them.
My Nexus 6 took 5.0.1 just fine, but my Nexus 7 does this same thing, running stock ROM/Bootloader/Recovery/etc. The ONLY thing done to it is the Fastboot OEM unlock, but I doubt that alone would stop it. I'm curious to know what resolves this ( other than downloading the factory image and flashing it without wiping the userdata )
Just got same error. I didnt even root phone, bought it today, it installed apps from backup of my previous Nexus 4 and OTA is failing.
cupfulloflol said:
With lollipop you can't take an OTA if you are rooted or running just about anything else modified (custom kernels, like ones that have force decrypt disabled also will cause it to error out).
You can still flash it manually by flashing the images. If you don't want to wipe, don't flash the userdata.img . Also, if you aren't currently encrypted, booting up with the stock kernel will force encrypt your device, so don't flash that if you want to stay that way. You can then re-root. There are more in depth instructions for doing this out there if you search around for them.
Click to expand...
Click to collapse
So basically the only way is to flash the image manually? If I choose not to flash userdata.img my phone data (photos, contacts, apps, etc) won't be erased right? But I will lose root correct? Thanks!
saman0suke1 said:
So basically the only way is to flash the image manually? If I choose not to flash userdata.img my phone data (photos, contacts, apps, etc) won't be erased right? But I will lose root correct? Thanks!
Click to expand...
Click to collapse
Correct, with Lollipop if you modify things you basically are then forced to manually take the updates. Not that big of a deal as you would likely be needing a PC to reinstall your custom recovery or re-root anyhow after the update.
Flashing userdata.img isn't necessary to update. Neither is recovery.img if you want to keep a custom recovery.
Also as I mentioned before, if you have disabled encryption on your device, if you flash the stock kernel (boot.img) and boot up with it you will re-enable forced encryption. You will need to flash a kernel with force encryption disabled if you want to keep running without encryption. If you haven't disabled encryption, or don't care if your device re-encrypts (this doesn't erase anything, just may take a few minutes on first boot) then this doesn't matter.
cupfulloflol said:
Correct, with Lollipop if you modify things you basically are then forced to manually take the updates. Not that big of a deal as you would likely be needing a PC to reinstall your custom recovery or re-root anyhow after the update.
Flashing userdata.img isn't necessary to update. Neither is recovery.img if you want to keep a custom recovery.
Also as I mentioned before, if you have disabled encryption on your device, if you flash the stock kernel (boot.img) and boot up with it you will re-enable forced encryption. You will need to flash a kernel with force encryption disabled if you want to keep running without encryption. If you haven't disabled encryption, or don't care if your device re-encrypts (this doesn't erase anything, just may take a few minutes on first boot) then this doesn't matter.
Click to expand...
Click to collapse
Can I manually update without removing root first? Am I going to receive an error if I don't remove it? based on what you said, I will remove userdata.img and recovery.img and that will not wipe my data right? Do I have to decompress those files or the flash-all.bat will take care of that? Thanks!
saman0suke1 said:
Can I manually update without removing root first? Am I going to receive an error if I don't remove it? based on what you said, I will remove userdata.img and recovery.img and that will not wipe my data right? Do I have to decompress those files or the flash-all.bat will take care of that? Thanks!
Click to expand...
Click to collapse
I'm interested as well. Mine is rooted and I have encryption disabled, and I have TWRP on my phone. I tried to sideload the OTA update, but I can't get my phone to start sideload. I even flashed the stock recovery to get it to go, and no dice. What do I do next?
Anyone? I would appreciate the feedback, thanks!
sideload refers to adb as I understand it. thats NOT how you flash....you use fastboot to flash so you can do it all by hand or use one of the toolkits that script it for you.
cmh714 said:
sideload refers to adb as I understand it. thats NOT how you flash....you use fastboot to flash so you can do it all by hand or use one of the toolkits that script it for you.
Click to expand...
Click to collapse
Thanks, I get that, however I wanted to know if I need to remove the root before installing the update and if I need to decompress the .zip with the .img files or the batch will do that? thanks!
saman0suke1 said:
Thanks, I get that, however I wanted to know if I need to remove the root before installing the update and if I need to decompress the .zip with the .img files or the batch will do that? thanks!
Click to expand...
Click to collapse
If your doing from the PC you need to extract the zip file from within the image and then fastboot them. As for root, when you do it from fastboot I dont believe it matters as you will lose root anyway and need to re-root via flashing SuperSU.zip
Worked great! Thanks! Android 5.0.1 and root, no data deleted
Is it normal to not have received an update beyond 5.0? I have had a Nexus 6 since day one, no rooting of any kind and I have not received 5.0.1.
I have done the sideload method, but I really don't want to bother with it. I do however want some of these terrible bugs I am experiencing squashed. This phone is giving me lots of issues lately.
Thanks!
Can you receive and install OTA updates with an unlocked bootloader? Everything else is stock, no disabled encryption or anything just unlocked bootloader.
naulsballs said:
Can you receive and install OTA updates with an unlocked bootloader? Everything else is stock, no disabled encryption or anything just unlocked bootloader.
Click to expand...
Click to collapse
Yes
Sent from my Nexus 6 using XDA Free mobile app
saman0suke1 said:
Worked great! Thanks! Android 5.0.1 and root, no data deleted
Click to expand...
Click to collapse
Can you provide steps for this. I am in the same situation. I have the 5.0.1 image downloaded, just wondering what files and what order to flash. Thanks
TOCS88 said:
Is it normal to not have received an update beyond 5.0? I have had a Nexus 6 since day one, no rooting of any kind and I have not received 5.0.1.
I have done the sideload method, but I really don't want to bother with it. I do however want some of these terrible bugs I am experiencing squashed. This phone is giving me lots of issues lately.
Thanks!
Click to expand...
Click to collapse
Try pulling your Sim card out and rebooting.
scotbotmosh said:
Can you provide steps for this. I am in the same situation. I have the 5.0.1 image downloaded, just wondering what files and what order to flash. Thanks
Click to expand...
Click to collapse
If you're planning to stay rooted (meaning no OTA in future) system.img, boot.img and radio.img in any order.
scotbotmosh said:
Can you provide steps for this. I am in the same situation. I have the 5.0.1 image downloaded, just wondering what files and what order to flash. Thanks
Click to expand...
Click to collapse
If you use fastboot, just run these commands in terminal (I used windows, so in order to flash using fastboot, put the image that you downloaded for the update in the same folder where you have fastboot and open a terminal there) you can rename the .img files to whatever you like and replace those name in the commands below:
fastboot flash bootloader <bootloader file name here>.img
fastboot flash radio <radio file name here>.img
Then reboot it:
fastboot reboot-bootloader
Then flash these:
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash system system.img
And that's it. These commands are run while the phone is connected to the PC, you have to turn it on by pressing volume up + volume down + power.
Good luck.

Need help upgrading to 5.1, Tired of flashing all the things.

My nexus 6 is unlocked and is running stock 5.0.1, rooted. . It has twrp and is decrypted.
I tried to sideload the 5.1 ota but it doesnt work.
I tried flashing the new 5.1 factory image but that doesnt work.
I'm tired of all this now, I just want my phone running stock 5.1 , locked , encrypted ,unrooted so I can just get ota next time from Google whenever they send it out.
Any guidance on what I need to do would be appreciated.
Use Wug's Nexus Root Toolkit :good:
Edit : Now I'm currently "Optimising app..." loop.
I tried using tge NRT to flash it back to stock but it didn't work.
I would first make a TWRP backup, then I would flash the boot image (decrypted if you want and make sure its the new one), system, radio and then reboot. I flashed everything fine while keeping twrp on my phone but I didn't like not having a custom ROM plus it was a little laggy so I restored a TWRP backup. My phone did bootloop for a while but eventually it booted 5.1. I would be careful since 5.1 seems to be having some issues in general.
http://forum.xda-developers.com/nex...gs-nexus-root-toolkit-v1-9-8-t2947452/page101
Quote:
Originally Posted by baudi11
Same thing happened to me. Here's what I did.
1. Press and hold power, volume up, and volume down. Keep holding them down until the phone boots into bootloader mode.
2. Go back to the toolkit and click the radio button labeled "Soft bricked/bootloop"
3. Click "Flash stock plus unroot"
4. Check all the boxes under "Settings", including "Post-flash factory reset" then click OK.
5. Follow the toolkit instructions from there.
This got me out of the bootloop, successfully installed 5.1, and kept all my apps and settings. Good luck.
Click to expand...
Click to collapse
It worked for me after that. Now I'm booted in 5.1
When I try to flash the factory images directly from Google I get the following errors even though the MD5 checks out.
archive does not contain 'boot.sig'
archive does not contain 'recovery.sig'
failed to allocate 1778070480 bytes
error: update package missing system.img
Press any key to exit...
celeriL said:
http://forum.xda-developers.com/nex...gs-nexus-root-toolkit-v1-9-8-t2947452/page101
It worked for me after that. Now I'm booted in 5.1
Click to expand...
Click to collapse
Thanks so much! This worked perfectly. Exactly what I needed. The past couple days have been so annoying but now it's over. Thanks again!
Giuseppe1010 said:
Thanks so much! This worked perfectly. Exactly what I needed. The past couple days have been so annoying but now it's over. Thanks again!
Click to expand...
Click to collapse
Glad to help!
You also could have extracted the zip and manually flashed the images ing fastboot
fastboot flash recovery recovery.img
fastboot flash system system.img
Etc
rootSU said:
You also could have extracted the zip and manually flashed the images ing fastboot
fastboot flash recovery recovery.img
fastboot flash system system.img
Etc
Click to expand...
Click to collapse
HaHaa. Tried and true. Always works.
prdog1 said:
HaHaa. Tried and true. Always works.
Click to expand...
Click to collapse
rootSU said:
You also could have extracted the zip and manually flashed the images ing fastboot
fastboot flash recovery recovery.img
fastboot flash system system.img
Etc
Click to expand...
Click to collapse
I agree that always works without fail and is much easier than a tool kit. I don't like tool kits because people need to learn the correct way to flash things before using one because its better to understand what you are flashing should there be an error.
Pilz said:
I agree that always works without fail and is much easier than a tool kit. I don't like tool kits because people need to learn the correct way to flash things before using one because its better to understand what you are flashing should there be an error.
Click to expand...
Click to collapse
I totally agree. Have done successful manual flash when tool kits failed. Seen on Nexus 6 already.Saved my soft brick with manual flash when tool kit failed.
Pilz said:
I agree that always works without fail and is much easier than a tool kit. I don't like tool kits because people need to learn the correct way to flash things before using one because its better to understand what you are flashing should there be an error.
Click to expand...
Click to collapse
I don't have anything against toolkits on some devices, so long as it is not used as a shortcut to learning the basics. That said, on a nexus, I don't really see any need to be honest.
rootSU said:
I don't have anything against toolkits on some devices, so long as it is not used as a shortcut to learning the basics. That said, on a nexus, I don't really see any need to be honest.
Click to expand...
Click to collapse
Thats how I feel because its so easy my wife could do it and she doesn't know anything about flashing. Toolkits are good for non Nexus devices, I just don't see a point when we need to learn things the correct way first.
I hope the bugs get sorted out so people don't hard brick their phones anyone
rootSU said:
You also could have extracted the zip and manually flashed the images ing fastboot
fastboot flash recovery recovery.img
fastboot flash system system.img
Etc
Click to expand...
Click to collapse
Im a complete fastboot novice since this is my first nexus device (always had samsung phones up until now) and although I managed to root and unlock the boot loader I want to make sure I learn all the basics including flashing (side loading?) subsequent updates.
So Im currently rooted, unlocked bootloader on a 5.01. custom rom. How would I go about flashing the 5.1 update manually?
Im assuming that once I extract the update zip file I will find all the images that need to be flashed....what order do i do them in? How do I take into account the boot loader locking issue people have been facing that results in a bricked device?
Thanks in advance.
EDIT: I found this thread which outlines what I need to do http://forum.xda-developers.com/nexus-6/general/using-image-to-update-nexus-6-data-loss-t3053158
I only have two question now:
1. Im assuming the system image will wipe out the custom rom im on but not the data will leaving the data cause a problem? whats the command line to wipe data?
2. This doesnt address the boot loader locking issue causing a brick that people have been facing. This process involves updating the boot loader what do i have to do to make sure I dont brick my device?
Thanks again
kingofkings11 said:
Im a complete fastboot novice since this is my first nexus device (always had samsung phones up until now) and although I managed to root and unlock the boot loader I want to make sure I learn all the basics including flashing (side loading?) subsequent updates.
So Im currently rooted, unlocked bootloader on a 5.01. custom rom. How would I go about flashing the 5.1 update manually?
Im assuming that once I extract the update zip file I will find all the images that need to be flashed....what order do i do them in? How do I take into account the boot loader locking issue people have been facing that results in a bricked device?
Thanks in advance.
EDIT: I found this thread which outlines what I need to do http://forum.xda-developers.com/nexus-6/general/using-image-to-update-nexus-6-data-loss-t3053158
I only have two question now:
1. Im assuming the system image will wipe out the custom rom im on but not the data will leaving the data cause a problem? whats the command line to wipe data?
2. This doesnt address the boot loader locking issue causing a brick that people have been facing. This process involves updating the boot loader what do i have to do to make sure I dont brick my device?
Thanks again
Click to expand...
Click to collapse
You could simply not update the bootloader. Bare minimum requirements is update system and boot (kernel). if you want to learn more about fastboot, go to general > All in one guide > Question 28.
If you do not update the bootloader, you'll never get an OTA but it doesn't seem like you're wanting that anyway.
In regards to data, yes it could cause a problem if you're using a custom rom. You can use fastboot erase data command. This also wipes your /sdcard though.

[MoFo IMG] 5.1 Rooted AT&T XT1097 with Tether

Below are the instructions for using MoFo to flash the AT&T XT1097 to 5.1. The rooted image has a modified build.prop file for free tether. Thanks go to @Slack3r for making the ext4 image and @btdownloads7 for developing the root method.
Since this is a 5.1 image, in order to get it to boot, you need to do the following BEFORE flashing the 5.1 system image:
1) Download the stock 5.1 files and extract them:
https://mega.co.nz/#!bN0BjKbI!zzq5b9wZBo-XFGNkcWtgw7mnXZgC5BWrEC-GZcGLELo
2) Using a root file explorer (like ES Explorer with root enabled), delete everything in /data/dalvik-cache and /cache - YOU MUST DO THIS!
3) Reboot into bootloader mode and run the commands below to flash the following stock 5.1 files for the XT1097:
Code:
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot flash recovery recovery.img
Do NOT flash the 5.1 bootloader (motoboot.img) or partition table (gpt.bin) - if you do, you will not be able to use MoFo ever again!!!!!
4) Download the rooted 5.1 image from here, extract it and flash it using MoFo.
https://mega.co.nz/#!ct8DlQxQ!DRMC_TvCcUk7V-FjCBfjsmIoOvw_f0WEdM7gx2waqzM
MD5 of the unzipped file = 146B6A65D925B985857A2F28D4294765
Note that with the XT1096 we had issues if we tried to boot into recovery after initially flashing the 5.1 system image so instead of booting into recovery and wiping cache where you might get weird flashing dead androids, we had to boot into system first.
Obviously if you want Xposed or anything else in the image, someone will need to add it in.
Thank you!
Those of us already rooted with mofo on 5.0.2 need to return to stock 5.0.2 first, correct?
Casyis said:
Thank you!
Those of us already rooted with mofo on 5.0.2 need to return to stock 5.0.2 first, correct?
Click to expand...
Click to collapse
No, the instructions as written in the OP are complete. Like the instructions say, you need to do step 2:
2) Using a root file explorer (like ES Explorer with root enabled), delete everything in /data/dalvik-cache and /data/cache - YOU MUST DO THIS!
Then you can flash the rest of the 5.1 stock files for your device EXCEPT for the bootloader (motoboot.img) and partition table (gpt.bin). Then use MoFo to flash the rooted 5.1 image for your device.
Thanks for clarifying.
I followed the instructions precisely, and the phone won't power up normally. It goes into recovery, and the android icon with exclamation just flashes intermittently. I'm unable to enter options to wipe cache. I can boot into recovery by holding volume down, but normal startup presents this behavior.
Any ideas?
EDIT: I chose BP Tools in boot options, and now the phone at least appears to be booting normally -- currently optimizing apps.
EDIT 2: Okay, so selecting BP tools evidently kicked the phone into booting normally. Looks like everything is just as it should be. Not sure what happened here, but in the end everything is good. Thank you (everyone involved) for getting this done for us!
Casyis said:
Thanks for clarifying.
I followed the instructions precisely, and the phone won't power up normally. It goes into recovery, and the android icon with exclamation just flashes intermittently. I'm unable to enter options to wipe cache. I can boot into recovery by holding volume down, but normal startup presents this behavior.
Any ideas?
EDIT: I chose BP Tools in boot options, and now the phone at least appears to be booting normally -- currently optimizing apps.
EDIT 2: Okay, so selecting BP tools evidently kicked the phone into booting normally. Looks like everything is just as it should be. Not sure what happened here, but in the end everything is good. Thank you (everyone involved) for getting this done for us!
Click to expand...
Click to collapse
This was happening with the XT1096 - you have to get it into system before recovery. You likely hit the wrong button and ended up in recovery instead of system. But once you get it into system, then it is fine.
Thanks again @JulesJam I am downloading now! Do you notice a big performance difference in 5.1? Will be nice to finally kill these memory bugs, so major thanks for that!
The OS is much snappier than 5.0.2. You can tell by going into multitasking and seeing how quickly the tiles load. Very, very nice. No re-draws at all yet since I flashed.
Step 2 implies that I'm already rooted. If I'm not, I assume I need to start with Step 0: Root the device with a 5.0 IMG?
What all would I need to fastboot flash from the stock files to return to stock @JulesJam ? My company just started using AirWatch service to get company email. Problem is airwatch will not work with root. Unfortunatly I will have to lose the ability to use MoFo.. Any help with this is greatly appreciated. Thanks!
bamachevrolet said:
What all would I need to fastboot flash from the stock files to return to stock @JulesJam ? My company just started using AirWatch service to get company email. Problem is airwatch will not work with root. Unfortunatly I will have to lose the ability to use MoFo.. Any help with this is greatly appreciated. Thanks!
Click to expand...
Click to collapse
FYI - like it says in the MoFo Noob Guide - MoFo trips the root checker and it is not able to be undone by flashing back to stock. I don't know how AirWatch works, but if it looks at the qe, then it will see you as rooted even if you aren't.
First thing I would do is flash back to 5.0.2 by flashing the stock 5.0.2 firware (link is in the MoFo Noob Guide)
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot flash recovery recovery.img
fastboot flash system system.img_sparsechunk1 (repeat this for all of the sparsechunks)
then boot into recovery and wipe the cache. Then boot into system. I believe it will need to downgrade the sensor firmware so allow that to happen.
Then boot into bootloader mode and see if your software status still says modified or not. Then boot into recovery and see what your qe status is. If after that your software status is still modified and your qe is still 1/1, I would do a factory reset and see if that corrects it. It probably won't though.
You will then have to decide whether or not you want to take the 5.1 OTA because your phone is going to want to upgrade. Instead of taking the 5.1 OTA which will upgrade your bootloader and partition table, you have the option of flashing stock 5.1 everything but the motoboot.img and gpt.bin. That would keep you stock 5.1 but still keep your bootloader and partition table on 5.0.2 so that if you wanted to sell the phone later, you could sell it with a copy of MoFo that still works. I put this out there because idk how AirWatch works and if flashing back to stock doesn't change your software status from modified or your qe from 1/1, you may not be able to use AirWatch, idk.
Thank you so much for the detailed explanation @JulesJam . Unfortunately I followed the instructions to the T and didn't run into any issues until I tried to boot into recovery. I got the dead android with a line under saying "no command". So I tried running system first. I got through the boot animation and then a black screen. I let the black screen sit for 30 min and nothing happened. I had the exact issue when installing 5.1, I was able to get it to boot using BT tools. Unfortunately this is not working now. I get the same black screen after the boot animation. I tried multiple times with no luck. I can however still get into fastboot without issues
Any ideas how I can get 5.0.2 to boot? Thanks again!
bamachevrolet said:
I get the same black screen after the boot animation. I tried multiple times with no luck. I can however still get into fastboot without issues
Any ideas how I can get 5.0.2 to boot? Thanks again!
Click to expand...
Click to collapse
For sure you flashed the 5.0.2 logo.bin, boot.img and all of the 5.0.2 system sparsechunks? That sounds like the system partition was not flashed properly.
Perhaps the 5.0.2 system files you have are corrupted? Are you sure the files you have are the stock 5.0.2 files for the AT&T XT1097?
bamachevrolet said:
I got the dead android with a line under saying "no command". !
Click to expand...
Click to collapse
That's OK as long as he is not flashing. When you have the dead android, go ahead and press and hold power then tap volume up to get into recovery and wipe the cache.
Thank you! I was able to get into recovery to wipe cache, but still won't boot.
I downloaded 5.0.2 from your noob guide, and flashed everything in the order of your first replied post. I am going to start over, just in case I missed something.
Don't think it matters but the sparsechunk starts at 0 in the AT&T file. I flashed the sparschunks in order, and in my case 0-8.
bamachevrolet said:
Thank you! I was able to get into recovery to wipe cache, but still won't boot.
Click to expand...
Click to collapse
How long do you let the blank screen sit before you try to get into bootloader mode? I remember sometimes it takes awhile for it to boot.
Also, the dalvik-cache may need to be wiped too. That would require a factory reset to do it so you could boot into recovery and do a factory reset. Unless there is some way to wipe the dalvik-cache from bootloader mode.
bamachevrolet said:
Don't think it matters but the sparsechunk starts at 0 in the AT&T file. I flashed the sparschunks in order, and in my case 0-8.
Click to expand...
Click to collapse
That's fine. I wasn't sure what number they started with.
bamachevrolet said:
I downloaded 5.0.2 from your noob guide, and flashed everything in the order of your first replied post. I am going to start over, just in case I missed something.
Click to expand...
Click to collapse
And after you do, let it sit at the blank screen for awhile to make sure that it isn't an issue of needing time to boot up. If it still won't boot, try the factory reset.
Thank you so much @JulesJam !!! I'm booted to stock 5.0.2 now. I did have to do a factory reset, but not too big of a deal. Unfortunately I forgot to backup my 48 tasker profiles...lol. So glad to have it back up. Thank you again!!!
---------- Post added at 11:06 AM ---------- Previous post was at 11:01 AM ----------
[/COLOR @JulesJam do you have a donation link?
bamachevrolet said:
Thank you so much @JulesJam !!! I'm booted to stock 5.0.2 now. I did have to do a factory reset, but not too big of a deal. Unfortunately I forgot to backup my 48 tasker profiles...lol. So glad to have it back up. Thank you again!!![
Click to expand...
Click to collapse
Glad it worked out, sucks about the tasker profiles though. So it seems like the dalvik-cache has to be wiped, too. I will note that in the future people should delete the contents of the dalvik-cache folder before flashing back to the earlier version of the software.
Does your software status still say modified in bootloader mode? What is your qe when you boot into recovery?
bamachevrolet said:
@JulesJam do you have a donation link?
Click to expand...
Click to collapse
No but thanks for the offer. If you want to donate, please donate to the ASPCA.

How to Flash 6.0.1 MM

can someone give me steps or link how to flash MM?
I am on 6.0.1 without twrp and just want to factory flash image
thanks
fromgeorgia said:
How to Flash 6.0.1 MM
can someone give me steps or link how to flash MM?
I am on 6.0.1 without twrp and just want to factory flash image
thanks
Click to expand...
Click to collapse
You are already on 6.0.1 Marshmallow. You said it yourself. You said you even still have stock recovery. So, seems like you don't need to do anything?
Maybe you wrote something wrong or left something out? Please clarify, and we'll be glad to help if we can.
ChazzMatt said:
You are already on 6.0.1 Marshmallow. You said it yourself. You said you even still have stock recovery. So, seems like you don't need to do anything?
Maybe you wrote something wrong or left something out? Please clarify, and we'll be glad to help if we can.
Click to expand...
Click to collapse
you are right i am, but phone crashes and when receiving phone calls and restarts sometimes so i want to try to reflash it. thanks
fromgeorgia said:
you are right i am, but phone crashes and when receiving phone calls and restarts sometimes so i want to try to reflash it. thanks
Click to expand...
Click to collapse
OK, then you need to flash this via RSDLite or ADB.
[FXZ] Official Stock Firmware 6.0.1 MCG24.251-5-5
https://forum.xda-developers.com/dr...-official-stock-firmware-6-0-1-mcg24-t3569334
You can google how to download/use RSDLite or ADB. But that's the most recent stock firmware you need to flash with either of those tools.
ChazzMatt said:
OK, then you need to flash this via RSDLite or ADB.
[FXZ] Official Stock Firmware 6.0.1 MCG24.251-5-5
https://forum.xda-developers.com/dr...-official-stock-firmware-6-0-1-mcg24-t3569334
You can google how to download/use RSDLite or ADB. But that's the most recent stock firmware you need to flash with either of those tools.
Click to expand...
Click to collapse
i've tried RSDLite but it was unable to detect the phone(drivers was right and phone was in recovery).
i will try ADB than. with ADB should i flash every partition manually?
fromgeorgia said:
i've tried RSDLite but it was unable to detect the phone(drivers was right and phone was in recovery).
i will try ADB than. with ADB should i flash every partition manually?
Click to expand...
Click to collapse
As far as I know you need to be on the bootloader screen, not recovery screen. Maybe that was your problem? RSDLite just automates a bunch of stuff ADB does.
Also, sometimes you need to use msfastboot instead of fastboot commands. I sort of remember why, but I don't want to state anything incorrectly. But try msfastboot if fastboot doesn't work.
For ROMs I use TWRP, so I'm not an ADB expert -- but I have used it. However, it's been over two years since I've had to flash a full firmware image via ADB (but I have flashed individual elements since then like modems, boot logos, etc.), so I'm just going to say yes flash every partition manually.
ChazzMatt said:
As far as I know you need to be on the bootloader screen, not recovery screen. Maybe that was your problem? RSDLite just automates a bunch of stuff ADB does.
Also, sometimes you need to use msfastboot instead of fastboot commands. I sort of remember why, but I don't want to state anything incorrectly. But try msfastboot if fastboot doesn't work.
It's been over two years since I've had to flash a full firmware image via ADB (but I have flashed individual elements since then), so I'm just going to say yes flash every partition manually.
Click to expand...
Click to collapse
thanks you're good man :good::laugh:

Categories

Resources