hello please help me, I have a problem with my phone moto X Xt1060, when I tried the rooter with root files. bat, after the operation is completed my phone could no longer has light so there was only the phone logo that was displayed then rebooted her, and so I have to redo the system and then j 'have this error to Moto x Xt1060 1gen gpt.bin preflash validation failed please help me. Thank you
Related
Hi guys! For the last days my phone had been giving some errors (usually the Maps application failing), that I didn't pay attention to.
Today when I woke up I tried using my phone and all applications were failing, so I just tried to turn it off and on, but it never went on again! It is just stuck in the red M.
My phone is fully stock and has Jelly Bean, I have never flashed it before or anything.
So I read some guides about flashing, and I tried doing it with RSD Lite but got the error : "no remval message notification" (screenshot attached)
Do you know what may be happening? Is there some chance for "bringing it back"?
Thanks!
I also tried unlocking it to no success:
(bootloader) BLKDISCARD ioctl /dev/block/mmcblk0 fail
(bootloader) Erase userdata fail
(bootloader) General Unlock failure!
(bootloader) OEM unlock failure!
FAILED (remote failure)
finished. total time: 8.550s
Thanks for your time trying to help me, I REALLY appreciate thatWell, before telling you the problem, here is my device info:
- Moto G 2nd GEN XT1068
- I was in Android 5.0.2 Stock
- Bootloader version 48.83(*)
- CID: 0x000CThe problem: A few days ago, with no reason (haven´t modified NOTHING at all), I turned on my device but it booted in bootloader mode... strange... so I just selected 'Normal powerup', after some seconds in the boot logo, it return to bootloader mode... always!.
Anyway, I siad: I just have to restore my firmware. Problem > I had not unlocked my device´s bootloader. Ok, I am just going to unlock (the same way as always) but, sometimes, when I enter this command mfastboot oem get_unlock_data I get this:
Code:
C:\Users\SebastianD\Desktop>mfastboot oem get_unlock_data
...
(bootloader) Failed to get unlock data, please try again!
FAILED (remote failure)
finished. total time: 5.008s
After many attempts I got my unlock data, then I did what I had to do: I went to Motorola Unlocking Website, entered my string, the code was sent to my e-mail (I did it with 2 e-mail accounts and got the same code), BUT! when I use the command mfastboot oem unlock UNIQUE_KEY I get, ALWAYS, this:
Code:
C:\Users\SebastianD\Desktop>mfastboot oem unlock [my_unlock_code]
...
(bootloader) Unlock code = [my_unlock_code]
(bootloader) unlock data invalid!
FAILED (remote failure)
finished. total time: 9.984s
I talked to Motorola service, but they say they do not have support for this because of their terms and stuff about the bootloader unlocking.
If you are more comfortable with spanish, here you can help me: LINK: Spanish Thread
This is freaking me out! I need help!
Reserved: To post the solution... if I get a solution.
Reserved: Just in case to provide more information to solve the problem.
Wrong sub forum
Sent from my Moto G 2014 using Tapatalk
Vidhanth said:
Wrong sub forum
Sent from my Moto G 2014 using Tapatalk
Click to expand...
Click to collapse
+1
@sebastiandg7 http://forum.xda-developers.com/moto-g-2014/help
I'm even friends with problem XT1068, does not generate the code to unlock only fault as shown below: Unit turns on shortly after return to the screen in AP Fastboot Flash
D:\android-sdk\platform-tools>fastboot oem get_unlock_data
...
(bootloader) Failed to get unlock data, please try again!
FAILED (remote failure)
finished. total time: 5.027s
I don't know why you have 'm' in front of 'fastboot oem get_unlock_data', anyway the instructions on this page are what I followed.
http://forum.xda-developers.com/moto-g-2014/general/wip-unlock-bootloader-moto-g-2nd-gen-t2875728
hi to everyone...
i was wondering if anyone can help me... i have a motorola g 2nd gen. and is attached to claropr my problem is that after flashing this file: Moto G 2014 [XT1063] Restore to Android 4.4.4 (21.85.23) now the phone boots to ap fastboot flash mode. and the following message is display:
version downgraded for boot
failed to validate boot image
any help will be appreciate....
sorry cant provide more info the phone cant boot to android.
titoscion2020 said:
hi to everyone...
i was wondering if anyone can help me... i have a motorola g 2nd gen. and is attached to claropr my problem is that after flashing this file: Moto G 2014 [XT1063] Restore to Android 4.4.4 (21.85.23) now the phone boots to ap fastboot flash mode. and the following message is display:
version downgraded for boot
failed to validate boot image
any help will be appreciate....
sorry cant provide more info the phone cant boot to android.
Click to expand...
Click to collapse
Try this: http://forum.xda-developers.com/moto-g-2014/development/rom-stock-rom-t2970427
To start, I have no knowledge on rooting other than simply using ODIN on one of my older Samsung devices.
I had got a Moto E5 Play the other day and decided to root it today. It was difficult finding a tutorial, but I found this one (https://www.rootingtutorials.com/android-rooting/root-moto-e5-play/)
I downloaded the Minimal ADB and Fastboot tool, and flashed the custom ROM that the post recommended me to do. Then downloaded Magisk and I couldn't install it directly as noted in the guide and after some research found out I had to flash it manually, but I only had the stock recovery for some reason. Found another tutorial from this website (https://forum.xda-developers.com/moto-e5/development/recovery-twrp-moto-e-5-play-james-t3796323)
I flashed the no-verity kernel and now my phone is in a boot loop. I freaked out and wiped the data and factory reset it. Now when I turn on my phone it says "bad key" in the top left corner and then it goes to the screen before the boot animations and stays there (motorola logo and powered by android at the bottom)
I am an idiot and shouldn't have done this. Is there anything I can do to fix it?
j256 said:
To start, I have no knowledge on rooting other than simply using ODIN on one of my older Samsung devices.
I had got a Moto E5 Play the other day and decided to root it today. It was difficult finding a tutorial, but I found this one (https://www.rootingtutorials.com/android-rooting/root-moto-e5-play/)
I downloaded the Minimal ADB and Fastboot tool, and flashed the custom ROM that the post recommended me to do. Then downloaded Magisk and I couldn't install it directly as noted in the guide and after some research found out I had to flash it manually, but I only had the stock recovery for some reason. Found another tutorial from this website (https://forum.xda-developers.com/moto-e5/development/recovery-twrp-moto-e-5-play-james-t3796323)
I flashed the no-verity kernel and now my phone is in a boot loop. I freaked out and wiped the data and factory reset it. Now when I turn on my phone it says "bad key" in the top left corner and then it goes to the screen before the boot animations and stays there (motorola logo and powered by android at the bottom)
I am an idiot and shouldn't have done this. Is there anything I can do to fix it?
Click to expand...
Click to collapse
Restore the stock firmware using the instructions here: https://forum.xda-developers.com/moto-e5/how-to/firmware-moto-e5-xt1944-4-dual-sim-t3820901
konradsa said:
Restore the stock firmware using the instructions here: https://forum.xda-developers.com/moto-e5/how-to/firmware-moto-e5-xt1944-4-dual-sim-t3820901
Click to expand...
Click to collapse
Thanks for replying.
I can't do this because I hard reset the phone and USB debugging is no longer on. "adb devices" recalls back nothing and inputting something like "adb reboot recovery" comes back with "no devices/emulators found".
Tried to input "fastboot flash partition gpt.bin" and get back:
target reported max download size of 535822336 bytes
sending 'partition' (45 KB)...
OKAY [ 0.004s]
writing 'partition'...
(bootloader) Validating 'gpt.default.xml'
(bootloader) Image primary_gpt failed validation
(bootloader) Preflash validation failed
(bootloader) Cancelling 'gpt.default.xml'
FAILED (remote failure)
finished. total time: 0.047s
What can I do?
j256 said:
Thanks for replying.
I can't do this because I hard reset the phone and USB debugging is no longer on. "adb devices" recalls back nothing and inputting something like "adb reboot recovery" comes back with "no devices/emulators found".
Tried to input "fastboot flash partition gpt.bin" and get back:
target reported max download size of 535822336 bytes
sending 'partition' (45 KB)...
OKAY [ 0.004s]
writing 'partition'...
(bootloader) Validating 'gpt.default.xml'
(bootloader) Image primary_gpt failed validation
(bootloader) Preflash validation failed
(bootloader) Cancelling 'gpt.default.xml'
FAILED (remote failure)
finished. total time: 0.047s
What can I do?
Click to expand...
Click to collapse
Did you boot the phone into fastboot mode? You don't need debugging on for fastboot.
The ,"bad key" is normal.
Looks like the wrong firmware or your bootloader is still locked
j256 said:
To start, I have no knowledge on rooting other than simply using ODIN on one of my older Samsung devices.
I had got a Moto E5 Play the other day and decided to root it today. It was difficult finding a tutorial, but I found this one (https://www.rootingtutorials.com/android-rooting/root-moto-e5-play/)
I downloaded the Minimal ADB and Fastboot tool, and flashed the custom ROM that the post recommended me to do. Then downloaded Magisk and I couldn't install it directly as noted in the guide and after some research found out I had to flash it manually, but I only had the stock recovery for some reason. Found another tutorial from this website (https://forum.xda-developers.com/moto-e5/development/recovery-twrp-moto-e-5-play-james-t3796323)
I flashed the no-verity kernel and now my phone is in a boot loop. I freaked out and wiped the data and factory reset it. Now when I turn on my phone it says "bad key" in the top left corner and then it goes to the screen before the boot animations and stays there (motorola logo and powered by android at the bottom)
I am an idiot and shouldn't have done this. Is there anything I can do to fix it?
Click to expand...
Click to collapse
you need to download 'lenovo moto smart assistant. when you opened the application you need to go to the rescue page. then click on moto phone and select your model. once the download is completed you need to click on rescue and the rescue will begin. after the rescue is completed you can boot your phone like it usually does.
This thread is one and half years old.
Sent from my jerry_cheets using XDA Labs
Hey everyone,
I know this is the wrong thread but there is not forum or thread for the Moto E5 Plus, please help
Im rooting a Moto E5 Plus and after I installed the rom I get Error: Failed to load kernel!
I get this message below
Start Up Failed:
Your device didnn't start up successfully
Use the Software Repair Assistant on computer
to repair your device
Connect your device to your computer to get the software repair assistant
AP Fastboot Flash Mode (Secure)
Fastboot Reason: UTAG *bootmode* configured as fastboot
Error: failed to load kernel!
Boot up failed
Its basically stuck in the bootloader besides being able to go into the twrp recovery.
Maybe you should ask your question wherever you got the rom cuz nobody knows what you're talkin about. Here is the E5 section. https://forum.xda-developers.com/moto-e5 good luck