Related
Hello all,
I have a friends sprint hero cdma that was rooted with z4root. He was flashing a mod that changed the text from green to orange and the phone froze. He waited quite a while then decided to hard reset. When he put the battery back in and rebooted the phone and the phone would not boot past white HTC bootlogo. The phone will not boot into recovery and the PC will recognize the phone, but the system will not mount so the ruu will not detect the phone either. HTC sync does not detect the phone being connected either. I am using a program called USBDeview and it shows the driver is there and says it is connected but none of the programs detect its connection. Any ideas?
Thanks in advance. Again this is not my phone and I am not familiar with rooting procedures with this phone, but I see a great learning experience in front of me and love these challenges.
this should be in QnA.
Hold power + vol down. will get you into HBOOT. if you flashed the eng-spl that unlocks fastboot you can erase and flash new. Tutorials are somewhere in this forum.
Sorry for the wrong forum. The phone will not hboot or boot into recovery
If it gets that far, you should be able to run the RUU. It'll restore everything to stock ;-)
Sent from my Epic using XDA App
The phone does not connect all the way for some reason. The RUU does not see device and neither does ADB. In device manger, when the device is connected it is assigned a drive letter and I can right click and go to properties and details and the description says android phone. I am out of ideas. Even when the device is connected and assigned a drive letter I can open file explorer and click on the device and the directory is blank. The SD card does not even show up, but if I take sd and put it in an adapter the sd card is still in tact with everything on it.
Sounds like a driver went haywire try searching the dev section for my thread on how to install adb. I know you have it already but try the diffrent drivers. I would post a link but I'm mobile. Hope it helps
Something.About.Me.U.Dont.Like
Its.Cool.I.Understand.
.AWAH.
Power off
hold vol up and power on
should be in fast boot mode
plug in your USB cable
should now be in fast boot usb mode
run RUU from the computer
RUU should recognise the phone and start installing
I will try this when I get home. So what would cause the phone to act like this? I have read quite a few threads in my quest to fix this phone and a ton of ppl claim bout the only way to brick the hero is by flashing a GSM vs of a. Zip instead of the cdma version. Is this true? I ask because the phone almost acts like it has been locked out somehow.
What happens when you boot into fastboot mode? I held the buttons but the hero still hangs at the white HTC screen.
nordy420 said:
I will try this when I get home. So what would cause the phone to act like this? I have read quite a few threads in my quest to fix this phone and a ton of ppl claim bout the only way to brick the hero is by flashing a GSM vs of a. Zip instead of the cdma version. Is this true? I ask because the phone almost acts like it has been locked out somehow.
Click to expand...
Click to collapse
Yes this is basically true. But if you get the HTC screen, chances are that it is not bricked. I have to ask, did you flash anything like a radio for GSM? If not, then you might need to just let it sit there for an exstended period of time and see if it boots. When I do certain things to my phone, it might take up to 15 minutes to get by the HTC logo screen.
nordy420 said:
What happens when you boot into fastboot mode? I held the buttons but the hero still hangs at the white HTC screen.
Click to expand...
Click to collapse
I wish I could take a screen shot and show you but the phone is not recognised at that point except by the RUU when it is waiting for bootloader. Bootloader is another name for fastboot.
It would be a white screen with green letters and it will say fastboot near the top under the green letters. At the bottom of the screen there will be 3 android characters on skate boards.
This is what you should see. Try again
Important: Make sure the USB is not conected at this time
Power off
Hold volume up, then press the red key (power on)
Fastboot screen comes up
At this point plug in the USB. It will change from Fastboot to Fastboot USB
Run RUU .5 or .6 from the computer
It will get to a point where the install says waiting for bootloader
from there it should start installing
If you can't get to the bootloader screen (fastboot) then I am not sure how to help you
Let me know if it works for you.
Edit: If you are not using ENG SPL or have S-Off read this post. You will need a working knowledge of how to use ADB.
http://forum.xda-developers.com/showthread.php?t=958968
Usually you are still able to get into fastboot, especially if you see the htc screen. Unless you (not really you) destroy the recovery and/or the misc partitions.Did you do this exactly (some people don't do it exactly) pull the battery, reinsert the battery, holding volume up and while holding volume up press the power (end call) button.
If you did then while the phone is stuck on the HTC screen do ......
Open up a command window. Either cd into your windows-sdk/tools folder or just type in the commands if you have the tools folder set as a global environment.
Code:
adb devices
Does it show you a device is connected? If it does you should be able to flash a new recovery image or at least a system.img to get it back up and running.
Thank you for the help by the way. I am not the owner of the phone, I am just more patient than the owner and have nothing to lose if it is screwed lol. http://androidforums.com/sprint-hero-all-things-root/259735-bricked.html. Here is his desperate cry for help after it happened. I own a Droid x and have no idea what he was actually trying to do, but maybe after you read what he did then maybe we can come up with a fix. I agree with you supporters that the phone is not bricked but it is sure being stubborn. Please let me know what ya think. Thanks.
unCoRrUpTeD said:
Usually you are still able to get into fastboot, especially if you see the htc screen. Unless you (not really you) destroy the recovery and/or the misc partitions.Did you do this exactly (some people don't do it exactly) pull the battery, reinsert the battery, holding volume up and while holding volume up press the power (end call) button.
If you did then while the phone is stuck on the HTC screen do ......
Open up a command window. Either cd into your windows-sdk/tools folder or just type in the commands if you have the tools folder set as a global environment.
Code:
adb devices
Does it show you a device is connected? If it does you should be able to flash a new recovery image or at least a system.img to get it back up and running.
Click to expand...
Click to collapse
I will try this when I get home. I did do a battery pull but I did not leave it out very long, but the screen never changed for me, just stayed white with HTC logo in the middle.
Be very sure to disconnect the USB. That was the step I was missing and I could not get it to boot to recovery when it was stuck at the logo. Once the USB was disconnected, took the battery out, put it back in, and held down the home button while pushing the power. That worked! Woot!
Lynne
No luck. The phone will not boot into anything to where a PC will recognize it.
nordy420 said:
No luck. The phone will not boot into anything to where a PC will recognize it.
Click to expand...
Click to collapse
Have you downloaded android commander and gave that a shot? androidcommander.com
android commander recognises the phone when it is at the logo screen. it will see all but the sdcard.
within android commander menu, there is a reboot to bootloader command
Ill try it, and report back
So I messed with android commander a little and could not get it to detect the device. I really think that it is a driver issue. I cannot get the HTC driver to install for the phone. A different driver has been installed for the device and windows will not let me manually install one. I can use the install legacy and the HTC driver is there but it will not correlate with the phone when connected.
I'll start out by saying I was careless and had not read various threads before flashing things and causing my issues. I've already bought a replacement phone but I'd like to see if there's any chance to revive the Moto X or not.
What happened:
I had unlocked the bootloader years ago. I was running the (mostly) stock Lollipop 5.1 with XPosed, and got noticed of a security update.
After fully charging the battery, I flashed stock recovery over my custom recovery (TWRP) and then, without thinking, got the latest image from Motorola without realizing it was a 4.4.4 image.
I flashed the system partition using this image thinking it would remove SU and that I could install the update - this soft-bricked the phone when I tried to boot.
Too late, but at this point I re-flashed TWRP and ran a backup. I used adb to extract the backup and my other files from the /sdcard partition.
Factory Reset. The phone boot up at this point.
I tried flashing the logo, gpt.bin (I forgot that Lollipop changed how partitioning worked) and then did another Factory Reset. Phone boots fine.
I then tried restoring the data from my nandroid backup. Rebooted once, and phone seemed to start. And then it went black.
At this point, the phone does not appear to boot at all. I can't use Vol Down + Power to boot into Fastboot, and if I connect to a computer, it does not see the device... USUALLY.
If I connect via USB to my Windows computer, and try to boot into Fastboot, the green LED behind the volume will flash once and my computer will signal the "Hardware connected" sound. I can try to run 'adb reboot bootloader' but adb reports that it doesn't see any devices. My system events note a USB Input Device was added but don't get any further. Within 5 seconds, the "hardware disconnected" sound fires. About 20 seconds later, this will repeat on its own.
I just tried making a fastboot cable from a spare micro usb cable... I may have done it wrong - but it does not seem to have had any effect. The result is the same. It's possible I didn't solder the connection well, though (it was difficult exposing the terminals on my particular cable).
The screen is always black and never lights up in any way.
It kind of makes me think that the device is attempting to boot, fails, and cycles. Is there anything I can do?
At this point I am able to get into fastboot after bricking my XT1060DEV in a similar way. Follow the guide as best as you can in this post. Toward the end of that thread you can see the sequence of events that led me to at least fastboot mode.
Awaiting a response from someone who might know which gpt.bin and bootloader I can flash to have more than a blank phone. I'll try to keep you updated.
EDIT:
You might find it easiest to get QHUSB set up using this guide. This guide has been superseded by the previously posted one, but some people still report success following it.
PiArc said:
At this point I am able to get into fastboot after bricking my XT1060DEV in a similar way. Follow the guide as best as you can in this post. Toward the end of that thread you can see the sequence of events that led me to at least fastboot mode.
Awaiting a response from someone who might know which gpt.bin and bootloader I can flash to have more than a blank phone. I'll try to keep you updated.
EDIT:
You might find it easiest to get QHUSB set up using this guide. This guide has been superseded by the previously posted one, but some people still report success following it.
Click to expand...
Click to collapse
I may not have a chance for a few days, but I will try this. I did try to download the software on the second link you provided and some of the links on that page were broken.
I'm not going to lie, navigating those threads is harsh.
Towards the end of the first linked thread you can see a post with what ended up getting me into fastboot. It might be a decent little roadmap to guide you in the right direction (plus, I think the files I indicate in that particular post are all still up).
Keep us updated!
ohioDroid said:
I'll start out by saying I was careless and had not read various threads before flashing things and causing my issues. I've already bought a replacement phone but I'd like to see if there's any chance to revive the Moto X or not.
What happened:
I had unlocked the bootloader years ago. I was running the (mostly) stock Lollipop 5.1 with XPosed, and got noticed of a security update.
After fully charging the battery, I flashed stock recovery over my custom recovery (TWRP) and then, without thinking, got the latest image from Motorola without realizing it was a 4.4.4 image.
I flashed the system partition using this image thinking it would remove SU and that I could install the update - this soft-bricked the phone when I tried to boot.
Too late, but at this point I re-flashed TWRP and ran a backup. I used adb to extract the backup and my other files from the /sdcard partition.
Factory Reset. The phone boot up at this point.
I tried flashing the logo, gpt.bin (I forgot that Lollipop changed how partitioning worked) and then did another Factory Reset. Phone boots fine.
I then tried restoring the data from my nandroid backup. Rebooted once, and phone seemed to start. And then it went black.
At this point, the phone does not appear to boot at all. I can't use Vol Down + Power to boot into Fastboot, and if I connect to a computer, it does not see the device... USUALLY.
If I connect via USB to my Windows computer, and try to boot into Fastboot, the green LED behind the volume will flash once and my computer will signal the "Hardware connected" sound. I can try to run 'adb reboot bootloader' but adb reports that it doesn't see any devices. My system events note a USB Input Device was added but don't get any further. Within 5 seconds, the "hardware disconnected" sound fires. About 20 seconds later, this will repeat on its own.
I just tried making a fastboot cable from a spare micro usb cable... I may have done it wrong - but it does not seem to have had any effect. The result is the same. It's possible I didn't solder the connection well, though (it was difficult exposing the terminals on my particular cable).
The screen is always black and never lights up in any way.
It kind of makes me think that the device is attempting to boot, fails, and cycles. Is there anything I can do?
Click to expand...
Click to collapse
Try reflashing twrp via fastboot, install custom ROM -OR- download latest XML for your variant flash via rsd lite or manual flash.
Note: When using the XML you will lose everything, including data on internal storage.
Hopefully this helps ?
Also, if your phone stays black it's likely the battery is dead. Leave it hook up for awhile or keep trying to boot into fastboot(while plugged into outlet, not PC) and leave it for a couple of hours, should charge.
I'm speaking from personal experience, just without having Xposed framework, lol.
Sent from my Moto X using Tapatalk
Hey everyone
Not sure if anyone can help
I just got some used 5th gen tablets, they were in a storage unit i just purchased. I turned on one of the fire units and it says it was a kids fire, so no real use to me. I hit power to standby and left it in my office, went back to list it and it was updated with new software. The second one, seems like it is stuck in a boot loop, comes on and goes off again. So i looked at the one that updated, said it now updated, had 5.6 on it, so i said maybe i could use it. Did some research, read you can but just android on it.
Well, i read you have to downgrade to 5.3 or older to install android. Not even sure if this is right.
So i followed some youtube genius with software from rootjunky.
I used the adb to flash update-kindle-global-37.5.4.2_user_542168620.bin
Everything was working, installing 100%, then i unplugged and selected 1 from the tablet to reboot.
Needless to say, nothing comes on now, no logo, no nothing, will not respond to recovery mode, down and power.
I just tried taking the back off and unplugging the battery and holding power 20 secs, nothing.
Anyone have any ideas to salvage these, or one of them or are they paperweights haha?
Good news is, the unit had all kinds of stuff in it, i have made my money back already, these were just bonus
Any help would be great, thanks
vetteguy82 said:
Hey everyone
Not sure if anyone can help
I just got some used 5th gen tablets, they were in a storage unit i just purchased. I turned on one of the fire units and it says it was a kids fire, so no real use to me. I hit power to standby and left it in my office, went back to list it and it was updated with new software. The second one, seems like it is stuck in a boot loop, comes on and goes off again. So i looked at the one that updated, said it now updated, had 5.6 on it, so i said maybe i could use it. Did some research, read you can but just android on it.
Well, i read you have to downgrade to 5.3 or older to install android. Not even sure if this is right.
So i followed some youtube genius with software from rootjunky.
I used the adb to flash update-kindle-global-37.5.4.2_user_542168620.bin
Everything was working, installing 100%, then i unplugged and selected 1 from the tablet to reboot.
Needless to say, nothing comes on now, no logo, no nothing, will not respond to recovery mode, down and power.
I just tried taking the back off and unplugging the battery and holding power 20 secs, nothing.
Anyone have any ideas to salvage these, or one of them or are they paperweights haha?
Good news is, the unit had all kinds of stuff in it, i have made my money back already, these were just bonus
Any help would be great, thanks
Click to expand...
Click to collapse
Permanently bricked; can't downgrade below 5.4. Sell it for parts or take it to the target range.
Thanks
Thanks for the reply
Ok, so the one that will not turn on at all , well technically it must be on when i plug it into my pc, it does chime, and then a few seconds later it chimes again. Like it is turning itself on and off, but because you can not see anything on the screen, you can not tell.
What about the second one? It turns on and you see amazon, but then it turns itself off. It does let you go to fastboot and recovery in the corner of the screen using the buttons. However, all you see is that, recovery only says recovery, does not go into the recovery menu.
Any ideas if the second one is recoverable?
Thanks
vetteguy82 said:
Thanks for the reply
Ok, so the one that will not turn on at all , well technically it must be on when i plug it into my pc, it does chime, and then a few seconds later it chimes again. Like it is turning itself on and off, but because you can not see anything on the screen, you can not tell.
What about the second one? It turns on and you see amazon, but then it turns itself off. It does let you go to fastboot and recovery in the corner of the screen using the buttons. However, all you see is that, recovery only says recovery, does not go into the recovery menu.
Any ideas if the second one is recoverable?
Thanks
Click to expand...
Click to collapse
If you can not access the stock recovery menu there is no known method for recovering these devices with one exception: early build devices (bootloader version 5.00 & 5.01) can boot a twrp image from fastboot. If that works you'll be able to install a custom ROM (two choices) assuming nothing else is wrong with the hardware.
fastboot boot <twrp.img>
thanks
I must be doing something wrong again, i download the twrp.imga dn saved it in the fast boot adb folder. I put the kindle in fastboot mode, and plugged into pc, driver installed, from folder i went in to command prompt. in command prompt i added fastboot twrp.img and hit enter command prompt shows all the command prompts and definitions.
Is there something else i should do?
Thanks
Davey126 said:
If you can not access the stock recovery menu there is no known method for recovering these devices with one exception: early build devices (bootloader version 5.00 & 5.01) can boot a twrp image from fastboot. If that works you'll be able to install a custom ROM (two choices) assuming nothing else is wrong with the hardware.
fastboot boot <twrp.img>
Click to expand...
Click to collapse
vetteguy82 said:
I must be doing something wrong again, i download the twrp.imga dn saved it in the fast boot adb folder. I put the kindle in fastboot mode, and plugged into pc, driver installed, from folder i went in to command prompt. in command prompt i added fastboot twrp.img and hit enter command prompt shows all the command prompts and definitions.
Is there something else i should do?
Thanks
Click to expand...
Click to collapse
You need to install this tool on the host PC. Make note of the installation folder as you will need to execute the fastboot command from there. You'll also need to copy any necessary files (eg: twrp image) to that folder unless versed in referencing other folders from the command prompt.
Keep in mind it is highly unlikely your looping device will be able to boot twrp. Only the earliest models had this vulnerability which Amazon quickly plugged.
I have been blundering my way though the internet to get my ROG Phone 2 rooted. I have unlocked the bootloader, I have a modified boot image from magisk, I have the ADB connection set up through USB and it works fantastically. I honestly don't know how I got it work, it involved many different driver update attempts and then figuring out I hadn't put the phone into USB debugging, but now fastboot doesn't work.
ADB will list the device, but fastboot cannot see it. I have tried rebooting the phone into the bootloader, but there is no connection on either. Not sure why I thought that would work, but I tried. I really don't understand enough about fastboot to get any farther on my own.
I have the tencent version and I was pretty certain I have the CN android 9.0 on it, but I am no longer certain of that. I am running windows 10.
This is my build number: PKQ1.190414.001.WW_Phone-16.0622.1906.19-0
I honestly don't know, but does that WW mean my tencent phone is running the WW firmware?
RichDoe252 said:
I have been blundering my way though the internet to get my ROG Phone 2 rooted. I have unlocked the bootloader, I have a modified boot image from magisk, I have the ADB connection set up through USB and it works fantastically. I honestly don't know how I got it work, it involved many different driver update attempts and then figuring out I hadn't put the phone into USB debugging, but now fastboot doesn't work.
ADB will list the device, but fastboot cannot see it. I have tried rebooting the phone into the bootloader, but there is no connection on either. Not sure why I thought that would work, but I tried. I really don't understand enough about fastboot to get any farther on my own.
I have the tencent version and I was pretty certain I have the CN android 9.0 on it, but I am no longer certain of that. I am running windows 10.
This is my build number: PKQ1.190414.001.WW_Phone-16.0622.1906.19-0
I honestly don't know, but does that WW mean my tencent phone is running the WW firmware?
Click to expand...
Click to collapse
Fun fact, I just got Fastboot access from my computer by using the side USB port and rebooting into the bootloader from ADB. Still not to sure about the version bit. I think I'm just going to give it whirl and brick my device, maybe.
RichDoe252 said:
I have been blundering my way though the internet to get my ROG Phone 2 rooted. I have unlocked the bootloader, I have a modified boot image from magisk, I have the ADB connection set up through USB and it works fantastically. I honestly don't know how I got it work, it involved many different driver update attempts and then figuring out I hadn't put the phone into USB debugging, but now fastboot doesn't work.
ADB will list the device, but fastboot cannot see it. I have tried rebooting the phone into the bootloader, but there is no connection on either. Not sure why I thought that would work, but I tried. I really don't understand enough about fastboot to get any farther on my own.
I have the tencent version and I was pretty certain I have the CN android 9.0 on it, but I am no longer certain of that. I am running windows 10.
This is my build number: PKQ1.190414.001.WW_Phone-16.0622.1906.19-0
I honestly don't know, but does that WW mean my tencent phone is running the WW firmware?
Click to expand...
Click to collapse
1. You are running a WW rom, but that doesn't necessarily mean your fingerprint is matched. To update you need to have both WW rom and WW fingerprint. You can check if your fingerprint is CN or WW using device info hw from playstore under 'system'
2. In order to root you need to have a matching root boot img for your current rom ie root img for 1906.19, just checking that your know this?
3. Have you managed to get the phone recognised using the cmd 'fastboot devices'? Also are you using the side port?
4.when you say bootloader, have you definitely got the phone in fastboot mode - hold vol up and power button until you see the screen with some options. That screen is fastboot mode, you don't need to select any further options. Once in that mode, connect to pc, open adb and run the fastboot devices cmd. Once your device is recognised, report back here for further steps
superbrick.
reg66 said:
1. You are running a WW rom, but that doesn't necessarily mean your fingerprint is matched. To update you need to have both WW rom and WW fingerprint. You can check if your fingerprint is CN or WW using device info hw from playstore under 'system'
2. In order to root you need to have a matching root boot img for your current rom ie root img for 1906.19, just checking that your know this?
3. Have you managed to get the phone recognised using the cmd 'fastboot devices'? Also are you using the side port?
4.when you say bootloader, have you definitely got the phone in fastboot mode - hold vol up and power button until you see the screen with some options. That screen is fastboot mode, you don't need to select any further options. Once in that mode, connect to pc, open adb and run the fastboot devices cmd. Once your device is recognised, report back here for further steps
Click to expand...
Click to collapse
Thanks for the reply! I did indeed get fastboot to work over USB. Fastboot devices reported back the serial number and everything. I did not know that the build need to match on both the boot and the rom, but that does make sense and I probably should have realized that before I went ahead and copied the rooted boot.img I had over. Then my phone couldn't boot up proper, and got stuck in fastboot. Then I went ahead and copied all of the contents of the same rom over and now it is literally just a black screen. Won't turn on any more. I think I super bricked it.
Sorry I didn't see your post earlier and I know I am not father into the deep end, but is there a way out from where I am.
RichDoe252 said:
Thanks for the reply! I did indeed get fastboot to work over USB. Fastboot devices reported back the serial number and everything. I did not know that the build need to match on both the boot and the rom, but that does make sense and I probably should have realized that before I went ahead and copied the rooted boot.img I had over. Then my phone couldn't boot up proper, and got stuck in fastboot. Then I went ahead and copied all of the contents of the same rom over and now it is literally just a black screen. Won't turn on any more. I think I super bricked it.
Sorry I didn't see your post earlier and I know I am not father into the deep end, but is there a way out from where I am.
Click to expand...
Click to collapse
Oh jeepers dude. So just a black screen... Can you at least boot into fastboot?
reg66 said:
Oh jeepers dude. So just a black screen... Can you at least boot into fastboot?
Click to expand...
Click to collapse
Nope. The only response I can get out of it now is when I plug it into the fastboot port, the computer recognizes that something was plugged in. I don't even get a device on a device manager.
RichDoe252 said:
Nope. The only response I can get out of it now is when I plug it into the fastboot port, the computer recognizes that something was plugged in. I don't even get a device on a device manager.
Click to expand...
Click to collapse
Try holding the power button for around 20 secs until it shuts down. Then try vol up and power together and see if you get back to fastboot. If that doesn't work try vol up vol down and power buttons all together. Then try again to put it in fastboot mode using vol up and power. Let us know what happens /if you can reach fastboot mode
reg66 said:
Try holding the power button for around 20 secs until it shuts down. Then try vol up and power together and see if you get back to fastboot. If that doesn't work try vol up vol down and power buttons all together. Then try again to put it in fastboot mode using vol up and power. Let us know what happens /if you can reach fastboot mode
Click to expand...
Click to collapse
Unfortunately, nothing. Holding power for 20 seconds showed nothing, and like wise for volume up and power. Battery was fully charged too. Had it plugged in for most of today while I was trying to get fastboot to work.
RichDoe252 said:
Unfortunately, nothing. Holding power for 20 seconds showed nothing, and like wise for volume up and power. Battery was fully charged too. Had it plugged in for most of today while I was trying to get fastboot to work.
Click to expand...
Click to collapse
Is there any sort of illumination to the black screen ie do you think the phone is on but the screen is black or do think the phone is completely off?
Holding power button for a while should switch it off after a while. Try holding for longer than 20 secs, then try booting into fastboot mode
---------- Post added at 04:00 AM ---------- Previous post was at 03:44 AM ----------
Well dude, it's 4 am here. Gotta get some sleep dude. Will check here when I wake. Good luck in the mean time
Still trying to get to sleep. How ya getting on? What about vol down and power buttons for 30+secs, can you try that and let us know the results
reg66 said:
Still trying to get to sleep. How ya getting on? What about vol down and power buttons for 30+secs, can you try that and let us know the results
Click to expand...
Click to collapse
Bro get to sleep! Such a good Samaritan
TikiThePug said:
Bro get to sleep! Such a good Samaritan
Click to expand...
Click to collapse
LOL! I would if I could, just can't sleep yet. Hopefully soon tho!
RichDoe252 said:
Unfortunately, nothing. Holding power for 20 seconds showed nothing, and like wise for volume up and power. Battery was fully charged too. Had it plugged in for most of today while I was trying to get fastboot to work.
Click to expand...
Click to collapse
Try a USB 2.0 port? Surprisingly this works for some phones even though it's compatible with 3.0.
reg66 said:
Still trying to get to sleep. How ya getting on? What about vol down and power buttons for 30+secs, can you try that and let us know the results
Click to expand...
Click to collapse
Well, It's been untouched for a day now, and it still will not react to input. No response from long hold on the power button. I will try again in the morning. Is it possible that I somehow wrote into the BIOS of the phone? Android does use a BIOS, right?
RichDoe252 said:
Well, It's been untouched for a day now, and it still will not react to input. No response from long hold on the power button. I will try again in the morning. Is it possible that I somehow wrote into the BIOS of the phone? Android does use a BIOS, right?
Click to expand...
Click to collapse
Android itself does not have a BIOS, since Android is an OS and BIOS is more similar to firmware. But yes, the phone does have firmware, and it could be that the mismatch in firmware versions (from which you tried to flash), has caused the bootloader to "not know what to do now" when trying to start the phone up.
One thing which comes with all phones with a Qualcomm chipset is something called Qualcomm Crashdump Mode. You can try to see if you can get your phone in EDL (emergency download) mode and restore the correct firmware in that way:
https://www.the***********.com/rog-phone-2-unbrick-guide (URL gets censored for some reason; it should be "the custom droid" with no spaces)
Also, if you continue to have driver issues with connecting the phone to your PC, are you able to test another PC or even a Mac if you have access to one? I find Windows can be a giant pain for getting ADB and fastboot to work properly at times.
Good luck and let us know how it goes.
reg66 said:
Still trying to get to sleep. How ya getting on? What about vol down and power buttons for 30+secs, can you try that and let us know the results
Click to expand...
Click to collapse
Ok, so here's where I am: I have left the phone unplugged for a long time now. Really had no effect. I just downloaded QPST and I can actually get my computer to see the phone. However, I am still not quite sure how to USE QPST and not make things worse. So this is my plan: I am going to look through the forums here for info on how to use QPST to get my phone working again. Not really sure what that will look like, but fastboot would be a good start. From there, it sounds like I have to get the original firmware back on it, and then go about the process of rooting once again.
Still leaves me with the issue that started me down the path of rooting this phone, but at least it will not longer be bricked.
RichDoe252 said:
Ok, so here's where I am: I have left the phone unplugged for a long time now. Really had no effect. I just downloaded QPST and I can actually get my computer to see the phone. However, I am still not quite sure how to USE QPST and not make things worse. So this is my plan: I am going to look through the forums here for info on how to use QPST to get my phone working again. Not really sure what that will look like, but fastboot would be a good start. From there, it sounds like I have to get the original firmware back on it, and then go about the process of rooting once again.
Still leaves me with the issue that started me down the path of rooting this phone, but at least it will not longer be bricked.
Click to expand...
Click to collapse
You may not HAVE to flash complete firmware, it is quite likely that the boot.img is causing the problem as you flashed an incompatible version. Below you'll flash the correct version which HOPEFULLY will fix your phone, provided you can get into fastboot mode now.
Haven't read back through all the thread so i can't recall all the details of where you're at. As far as i can tell you're still running WW 16.0622.1906.19-0, correct? Can you get the device to now boot into fastboot mode? (from a powered off state, press and hold vol up and power at the same time. You should then be presented with some options, DON'T select any option. With that menu screen open is fastboot mode.
1. Download and install ADB Fastboot from here to C: drive of your pc/laptop.
2. With your phone in fastboot mode (as detailed above) connect it to pc/laptop using the side port of the phone.
3. Navigate to C:\Program Files (x86)\Minimal ADB and Fastboot folder and double click the cmd-here.exe, this will open a cmd window.
4. Type 'fastboot devices' to check that it's recognised, there should be a serial/key shown after entering that cmd.
5. Provided the serial/key is shown in fastboot mode, download the following boot.img (which is for WW 1906.19) from here.
6. Copy that boot img to the same folder you have open for ADB (C:\Program Files (x86)\Minimal ADB and Fastboot)
7. In the cmd window type 'fastboot flash boot boot.img'.
Now, that boot img is the STOCK boot img for your rom version. Don't worry about rooting for now (if i recall correctly, your phone won't boot to system), let's just try to get the phone booting first. Providing there are no errors when flashing the boot img, on the phone fastboot menu, scroll through and choose 'restart'.
Let me know if the device boots to system now... Good luck
I'll pm you my email address so you'll be able to get hold of me if you get stuck at any stage...
EDIT: was forgetting you tried so many times to get into fastboot mode, without success.
---------- Post added at 08:59 PM ---------- Previous post was at 08:17 PM ----------
Dude, is your phone screen still black but switched on? When you tap the screen does it vibrate. I'm thinking you might already be in edl mode (which could be a good thing). Let us know
Check your pm's dude for further info. I can't post links to the site required so have sent via pm
TikiThePug said:
Android itself does not have a BIOS, since Android is an OS and BIOS is more similar to firmware. But yes, the phone does have firmware, and it could be that the mismatch in firmware versions (from which you tried to flash), has caused the bootloader to "not know what to do now" when trying to start the phone up.
One thing which comes with all phones with a Qualcomm chipset is something called Qualcomm Crashdump Mode. You can try to see if you can get your phone in EDL (emergency download) mode and restore the correct firmware in that way:
https://www.the***********.com/rog-phone-2-unbrick-guide (URL gets censored for some reason; it should be "the custom droid" with no spaces)
Also, if you continue to have driver issues with connecting the phone to your PC, are you able to test another PC or even a Mac if you have access to one? I find Windows can be a giant pain for getting ADB and fastboot to work properly at times.
Good luck and let us know how it goes.
Click to expand...
Click to collapse
Just dropping you a quick note to say thanks for thanks! LOL. Yeah, your post earlier seems like the best place to go. Have used Miflash Tool a few times on Xiaomi devices, it's pretty good and straight forward. Should be a LOT easier than using QPST and having to change EMMC to UFS.
Can't remember where i saw it now, but i'm sure i read that if the phone screen is black (but switched on) and vibrates, then it's likely to be in EDL mode already. Which will hopefully be good news for @RichDoe252. Before that (having never been in that situation), i wasn't aware that an all black screen could mean EDL mode is active. Fingers crossed for Rich it'll all work out just fine.
@RichDoe252 If all goes successfully using the QPST file download (and using the Miflash Tool the guide mentions in the pm i sent you) and flashing, DON'T ROOT JUST YET!!!! LOL. Let us know how it goes and then we can look into, and point you in the right direction, for getting you rooted and up to date on latest A9 or A10 whichever you'd prefer
Well I must say Rich, I'm surprised you haven't been back here yet to give any updates on progress!! Sent you a couple of emails through pm... Man, if it was my fairly expensive phone that was in the poo pan, I'd be all over trying to fix it lol
reg66 said:
Well I must say Rich, I'm surprised you haven't been back here yet to give any updates on progress!! Sent you a couple of emails through pm... Man, if it was my fairly expensive phone that was in the poo pan, I'd be all over trying to fix it lol
Click to expand...
Click to collapse
First off, you are a freaking saint. I really do appreciate all the help you have been offering up, and I am sorry I have not been very quick with a response. As my phone currently stands, I get 0% response from anything I do to it. No vibrate, nothing. No indication it even is plugged in. I had it connected to my PC with QPST installed, and it was able to pick up that the phone was there, and then immediately tried to download something to it. Not sure what, not sure why, but that kinda typifiies my interaction with this whole process so far. If you haven't guessed, I'm kinda in over my head.
Back to the problem: QPST started some opperation to download something to it. Wouldn't let me do anything else, said the phone was in "download mode". Either way it stopped at 30% and didn't progress for 30 minutes, so I tried to unplug it and plug it back in. Same interaction. Unable to do anything to the phone, no reaction from the phone what so ever. This was, by the way, plugged into the fastboot side port.
I saw that you PM'ed me, and now I can't find the email notification or the PMs on the site. Forgive me for being unfortunately new at this. I will get back to you bud, and thank you again.
I received my new sony 1 ii and have checked and the bootloader can be unlocked and the phone can be rooted. I thought I was away to the races but I'm mystified. I can't get the phone to boot into fast boot.
I appears I have the drivers in place and the phone is recognized by the computer but no luck with fast boot.
I have searched and can't seem to find out why this is. I suspect some kind of driver issue with win10 but when I connect to the computer with the phone off and hold the up-volume nothing happens. I have also tried to boot into recovery mode and that does not work as well. Any help would be appreciated.
blkair445 said:
I received my new sony 1 ii and have checked and the bootloader can be unlocked and the phone can be rooted. I thought I was away to the races but I'm mystified. I can't get the phone to boot into fast boot.
I appears I have the drivers in place and the phone is recognized by the computer but no luck with fast boot.
I have searched and can't seem to find out why this is. I suspect some kind of driver issue with win10 but when I connect to the computer with the phone off and hold the up-volume nothing happens. I have also tried to boot into recovery mode and that does not work as well. Any help would be appreciated.
Click to expand...
Click to collapse
On Sony devices you need to power off and hold volume up and plug in the USB cable. That should leave the blue LED to indicate fastboot mode. I'm not 100% sure since it's been a while since I've messed around with Sony devices
Thanks for the input. I have done that and am still unable to action ADB - It is a little confusing since the phone only shows the blue light and nothing else.
If I normally boot the phone it will register as an ADB device. I also find it strange that it will not boot into recovery. The android icon flashes but when you release it boots to safe mode. I assume it is a driver issue but it is not revealing its self to me . Cheers
blkair446 said:
Thanks for the input. I have done that and am still unable to action ADB - It is a little confusing since the phone only shows the blue light and nothing else.
If I normally boot the phone it will register as an ADB device. I also find it strange that it will not boot into recovery. The android icon flashes but when you release it boots to safe mode. I assume it is a driver issue but it is not revealing its self to me . Cheers
Click to expand...
Click to collapse
The blue light is fastboot mode. There is no ui interface in fastboot for sony devices. Just a blue light and black screen.
R800x_user said:
On Sony devices you need to power off and hold volume up and plug in the USB cable. That should leave the blue LED to indicate fastboot mode. I'm not 100% sure since it's been a while since I've messed around with Sony devices
Click to expand...
Click to collapse
Same person but had to change user name -- more on the issue
I managed to unlock the boot loader and it seems that at every step for rooting I am running into curve balls. Windows was not working for me so I managed to unlock the bootloader with Linux and going on to the next step I had to go back to windows to find a current factory ROM.
The next issue: going back to the "how to" I am unable to located boot.xxxxx.sin in the factory ROM and the closest I could find is boot_x-Flash-ALL-2389.sin and that doesn't work.
In the boot directory all files are bootloader_X_44 and a combination of zip and sin files
Can anyone steer me through the muddy waters
The factory rom was downloaded through XperiaFirm application
blkair446 said:
Same person but had to change user name -- more on the issue
I managed to unlock the boot loader and it seems that at every step for rooting I am running into curve balls. Windows was not working for me so I managed to unlock the bootloader with Linux and going on to the next step I had to go back to windows to find a current factory ROM.
The next issue: going back to the "how to" I am unable to located boot.xxxxx.sin in the factory ROM and the closest I could find is boot_x-Flash-ALL-2389.sin and that doesn't work.
In the boot directory all files are bootloader_X_44 and a combination of zip and sin files
Can anyone steer me through the muddy waters
The factory rom was downloaded through XperiaFirm application
Click to expand...
Click to collapse
May I know how did you unlock the bootloader? Did you use xperia 1 as your device in https://developer.sony.com/develop/open-devices/get-started/unlock-bootloader/#unlock-code?
I have already installed usb drivers and have the platform tools. But everytime I boot my device to fastboot, whether using "adb reboot bootloader" or power button + volume up, screen only shows black (led is solid blue). I did left it for a couple of minutes, nothing happened.
jepher said:
May I know how did you unlock the bootloader? Did you use xperia 1 as your device in ?
I have already installed usb drivers and have the platform tools. But everytime I boot my device to fastboot, whether using "adb reboot bootloader" or power button + volume up, screen only shows black (led is solid blue). I did left it for a couple of minutes, nothing happened.
Click to expand...
Click to collapse
I unlocked my bootloader after obtaining the unlock code from sony developers I used adb/fastboot commands in linux mint. Pretty straight forward but the next step for rooting is giving me issues. Just select xperia 1 and the imei number will identify your phone -- cheers
blkair446 said:
I unlocked my bootloader after obtaining the unlock code from sony developers I used adb/fastboot commands in linux mint. Pretty straight forward but the next step for rooting is giving me issues. Just select xperia 1 and the imei number will identify your phone -- cheers
Click to expand...
Click to collapse
Yes I followed those. But may I know how long it took you to finish the unlocking?
Install ADB/SDK drivers
Download platform tools
Plug the device
Make sure adb can see my device
Use adb reboot bootloader command
Device booted to fastboot mode
Execute the command with the unlock code
...stucked here
If I miss something. Please do let me know
jepher said:
Yes I followed those. But may I know how long it took you to finish the unlocking?
Install ADB/SDK drivers
Download platform tools
Plug the device
Make sure adb can see my device
Use adb reboot bootloader command
Device booted to fastboot mode
Execute the command with the unlock code
...stucked here
If I miss something. Please do let me know
Click to expand...
Click to collapse
I assume you are using windows and I must say I gave up trying to get win10 to work and I was stuck at the same place you are. I then switched to linux and it went a lot smoother and I didn't need all those tools as laid out in the description.
In linux you must use the phone to go into fastboot mode if you boot from computer it actually boots to a visible screen on the phone and I didn't have connection that would take the command line commands. Linux is very good because if you are missing something it will give you a link or a command line input when you execute the ADB or Fastboot command.
I have run a windows/linux dual boot desktop for a while now and I'm no expert but coming from the era of command line I can muddle through. Sorry if I can't give you more info on windows but win10 is such a pain and I find that with a lot of things linux works better. If I didn't need adobe acrobat I would not even bother with windows.
cheers
blkair446 said:
I assume you are using windows and I must say I gave up trying to get win10 to work and I was stuck at the same place you are. I then switched to linux and it went a lot smoother and I didn't need all those tools as laid out in the description.
In linux you must use the phone to go into fastboot mode if you boot from computer it actually boots to a visible screen on the phone and I didn't have connection that would take the command line commands. Linux is very good because if you are missing something it will give you a link or a command line input when you execute the ADB or Fastboot command.
I have run a windows/linux dual boot desktop for a while now and I'm no expert but coming from the era of command line I can muddle through. Sorry if I can't give you more info on windows but win10 is such a pain and I find that with a lot of things linux works better. If I didn't need adobe acrobat I would not even bother with windows.
cheers
Click to expand...
Click to collapse
Yes I am using w10. Will try linux later. I have searched everywhere and stucked at the same step. Thank you.
I have managed to unlock the bootloader and root the phone. But problem is. I can't write on the root folder.
More to this I think I might have located the boot file boot_X-flash-all-2396.sin but using magisk it returns no boot image found. I see the guide says use the canary built but that seems to have been shut down, so at an impasse here and am still reaching out for help - damn op phone were never this funky
I might as well put this one out there then -- Is there anyway to flash a op 8 pro in2025 to dual sim - it's the cause of this painful trip
I was reverting my phone to unroot and locked bootloader. And it is saying that "Your Device is corrupt. It can't be trusted and will not boot" loop.
I tried flashing it using the new flasher. But after flashing, it will do SONY boot loop. If I connect it to a charger it goes back to "Your Device is corrupt. It can't be trusted and will not boot" loop.
I can't use Sony Companion since it is saying that my battery is low, and I can't charge the phone since it will just continue looping.
Do you know/have any recovery.img?
Edt: Fixed my phone. Relocked the bootloader
jepher said:
I was reverting my phone to unroot and locked bootloader. And it is saying that "Your Device is corrupt. It can't be trusted and will not boot" loop.
I tried flashing it using the new flasher. But after flashing, it will do SONY boot loop. If I connect it to a charger it goes back to "Your Device is corrupt. It can't be trusted and will not boot" loop.
I can't use Sony Companion since it is saying that my battery is low, and I can't charge the phone since it will just continue looping.
Do you know/have any recovery.img?
Edt: Fixed my phone. Relocked the bootloader
Click to expand...
Click to collapse
Any chance you could post the steps to relock successfully? I presume using the fastboot commands etc though did you then just re run the command to relock the bootloader? Many thanks
cd993 said:
Any chance you could post the steps to relock successfully? I presume using the fastboot commands etc though did you then just re run the command to relock the bootloader? Many thanks
Click to expand...
Click to collapse
Yes. Relock it using fastboot command.
I use ubuntu to do it. If you can run fastboot commands in windows10 lucky you.