Hi..
I was trying to upgrade my samsung galaxy s plus (GT-19001) device to Android 4.0.4.
i just installed CWM-based recovery v5.5.0.4 on my device by rebooting and selecting (install zip from sd card).
------using mentioned combination of keys -------
Then i placed the files in my phone's internal SD Card.
files are mentioned below:
1-> cm-9-20121011-ivendor-ariesve-rc5.zip
2-> gapps-ics-20120429-signed.zip
3-> recovery-clockwork-6.0.1.2-ariesve.zip
then install 1 by choosing from internal SD card and then 2nd file.
my device prompted completion success messages but it took very short time.
----------------------------------------------------------------------------------------------------------------------
now what happened after doing this. my device is displaying same booting screen of CWM-based recovery v5.5.0.4 on each re-boot.
i treid many times by unplug the battrey but unfortunately unsuccessfull.
After that i did Wipe data/factory reset and wipe cache partition.
----------------------------------------------------------------------------------------------------------------------
I tried it through window's based utility Odin v4.43 but it could detect my device usb driver even after success of USB driver installation.
it didn't display Added in message box.
now what should i do ?
i already installed samsung Kies but still undetected.
I tried some old version of Odin 3v1.8 , it detected the port and displayed Added but failed to write ROM on my device.
-----------------------------------------------------------------------------------------------------------------------
My desktop machine's OS : windows 8 64 bit enterprise edition.
----------------------------------------------------------------------------------------------------------------------------------------------------------
I am unable to install new ofor revert back my OS because when i Hold Vol Down + Home + Power, This is not putting me in Download Mode instead Ramdump Mode.
I need your guidence to resolve the issue. Thanks in advance.
Please ask for further details if required.
I'm not sure I got exactly what you did.
1) You installed CWM recovery.
2) You rebooted into recovery.
3) You installed the CM ROM zip.
4) You installed the GApps zip.
5) You rebooted.
Am I right ? And now you only get access to the recovery ?
If you're coming from a GingerBread ROM, this is normal. Simply, re-install the ROM again (and the GApps obviously). If it doesn't work, tell us.
support required
Einril said:
I'm not sure I got exactly what you did.
1) You installed CWM recovery.
2) You rebooted into recovery.
3) You installed the CM ROM zip.
4) You installed the GApps zip.
5) You rebooted.
Am I right ? And now you only get access to the recovery ?
If you're coming from a GingerBread ROM, this is normal. Simply, re-install the ROM again (and the GApps obviously). If it doesn't work, tell us.
Click to expand...
Click to collapse
Hi Einril.
I try to summarize in some chunks for better understanding.
=======================================================================================
Hi.
I just started with CWM-based recovery v5.5.0.4 and placed all above mentioned files/packages into the device internal SD card.
That's what i did :
1). Entered into the recovery mode menu by holding down Volume Up + Power and installed CWM-based recovery v5.5.0.4 zip from the selection of Internal SD Card .
2). After reboot, i came up again in Recovery mode using CWM-based recovery v5.5.0.4 application.
3). Now installed cm-9-20121011-ivendor-ariesve-rc5.zip by the navigation of "Install zip from SD".
It took hardly 4 to 5 seconds and displayed a message that it completes . no flash screen or anything came up and reboot.
4). After that installed gapps-ics-20120429-signed.zip by the navigation of "Install zip from SD".
It displayed same complete message but within 5 to 8 seconds i think.
5). I Wipe data/cache/Dalvik cache after above step and then again repeat the process.
After that i did Wipe data/factory reset and wipe cache partition.
Now when i try to start my device then each time it comes into the CWM-based recovery v5.5.0.4' s recovery mode.
Ask further please if anything is unclear, i have tried too many things with it but yet not soft bricked.
I am able to switch into Download mode.
Did you try to re-install the ROM from the recovery ? (flash cm-9-20121011-ivendor-ariesve-rc5.zip again)
new post
Einril said:
Did you try to re-install the ROM from the recovery ? (flash cm-9-20121011-ivendor-ariesve-rc5.zip again)
Click to expand...
Click to collapse
Hi Erinil,
I think i installed but not sure.
Could you elaborate the re-install ROM steps ?
I tried but same recovery display of CWM-based recovery v5.5.0.4, comes again and stay on recovery mode screen.
How my OS will be started?
It might be possible , i am doing something wrong.
Could you enlist the steps?
Ok.
1) Boot into recovery.
2) Wipe data/Factory reset.
3) Wipe cache.
4) Go to Advanced, then wipe Dalvik cache.
5) Go back, go to Mount & Storage, then Format System.
6) Go back, go to Install zip from SD Card => Choose zip from SD Card => cm-9-20121011-ivendor-ariesve-rc5.zip.
7) Do the same thing for the gapps zip.
8) Wipe data/Factory reset again (just to be sure).
9) Reboot.
This, I think, is the cleanest install you can do. Tell me the result.
Einril said:
Ok.
1) Boot into recovery.
2) Wipe data/Factory reset.
3) Wipe cache.
4) Go to Advanced, then wipe Dalvik cache.
5) Go back, go to Mount & Storage, then Format System.
6) Go back, go to Install zip from SD Card => Choose zip from SD Card => cm-9-20121011-ivendor-ariesve-rc5.zip.
7) Do the same thing for the gapps zip.
8) Wipe data/Factory reset again (just to be sure).
9) Reboot.
This, I think, is the cleanest install you can do. Tell me the result.
Click to expand...
Click to collapse
Einril I tried it same as you explained in steps.
It didn't worked nor display any error during this process.
I think my problem is that. when i start my device it automatically entered into the recovery mode of CWM-based recovery v5.5.0.4..
whether i hold Vol+ and Powerbutton or not, it entered into the recovery mode each reboot.
It might be possible that OS has been installed sucessfull but how the OS will be started now?
Hum, that's strange. You say you can access to Download Mode ? Are you able to flash back the Samsung stock ROM ?
Hi Einril,
What does that mean? Means that Reverting to Gingerbread through Desktop Window OS?
I am unable to revert from my One Laptop (i7 3610 & WIndow 8 - 64 bit) but i am able to revert from my OLD laptop (OS is : window 7 32 bit)
Ok, I heard that some people are having issues with USB drivers on Windows 8. But if you can restore Gingerbread with your old computer, this is great.
Can you try to re-install a stock gingerbread firmware, with re-partition enabled, and then to try again the procedure I gave you ? This way, we are sure that your previous attempts have no effects on the result.
Einril, I have installed stock gingerbread firmware on my device and it is working now.
now guide please how to re-partition? Do you mean using CWM recovery ?
Could you simply enlist the thing which i will have to do now on fresh gingerbread OS?
I 'll tell you today night because right now i am not at home.
Well, if your gingerbread frmware is working, you don't need to repartition.
Now, simply re-install ClockworkMod Recovery, and re-do the whole installation process I gave you. By the way, you said you installed ClockworkMod recovery by flashing a zip in recovery. Isn't it supposed to be a .tar.md5 to flash via Odin ?
Yes i installed ClockworkMode Recovery from recovery mode.
I haven't tried with .tar.md5 using Odin4.43.
I 'll try with both throught Clockworkmode and Odin.
In fact i have tried many time 2-3 months ago too through TeamWin Recovery . problem was same.
It didn't start my OS instead displaying its recovery screen and operations.
i tried but all in vain.
Couldn;t be successful.
it just start from CWM recovery mode and so. not switching into the other mode.
Hi..
I want to clean install Android 4.0.4 OS on my Samsung galaxy s plus (GT-19001) device.
Clean install means that i 'll have to install OS from scratch. Does i need Micro USb Jig for this purpose?
I have below files.
1-> cm-9-20121011-ivendor-ariesve-rc5.zip
2-> gapps-ics-20120429-signed.zip
3-> recovery-clockwork-6.0.1.2-ariesve.zip
4> CWM-based recovery v5.5.0.4
Guide me in simple steps , i tried many times to install ICS (Android 4.0.4) but unfortunately unsuccessfull each time.
Why it didn't work for me?
I have tried in many ways. Thanks in advancee
Hey,
Could you tell me what was unsuccessful about the install? Did it stop installing, did it bootloop, so on so forth?
But this is how I flashed CM9 onto my I9000, and I know that the I9001 is very similar so...
1.) You've got CWM, sweet. Boot into recovery. Make a bckup of your data through the option provided.
2.) Wipe data/cache/Dalvik cache. The first two are pretty simple to do, the last one is under "Advanced" settings.
3.) Now that you've got that, select "Install zip from SD". Navigate to where your CM9 file is. Select and confirm. Wait for it to flash in...
4.) At this point you might get a recovery bootloop. Don't panic here- just take out the battery, reinsert. Reboot into recovery. You should see that your recovery has been updated.
5.) Reselect the rom from the "Install zip from SD" option. This time it should start flashing in. Wait for it to finish, then it should reboot normally. Be patient as it boots up for the first time.
6.) Once you've done so, reboot into recovery again but this time select the gapps zip.
Unless the I9001 is different in a major way in terms of installing, that should work. I'm not quite sure...
Hope I helped
Sent from my GT-I9000
support required
Soryuu said:
Hey,
Could you tell me what was unsuccessful about the install? Did it stop installing, did it bootloop, so on so forth?
But this is how I flashed CM9 onto my I9000, and I know that the I9001 is very similar so...
1.) You've got CWM, sweet. Boot into recovery. Make a bckup of your data through the option provided.
2.) Wipe data/cache/Dalvik cache. The first two are pretty simple to do, the last one is under "Advanced" settings.
3.) Now that you've got that, select "Install zip from SD". Navigate to where your CM9 file is. Select and confirm. Wait for it to flash in...
4.) At this point you might get a recovery bootloop. Don't panic here- just take out the battery, reinsert. Reboot into recovery. You should see that your recovery has been updated.
5.) Reselect the rom from the "Install zip from SD" option. This time it should start flashing in. Wait for it to finish, then it should reboot normally. Be patient as it boots up for the first time.
6.) Once you've done so, reboot into recovery again but this time select the gapps zip.
Unless the I9001 is different in a major way in terms of installing, that should work. I'm not quite sure...
Hope I helped
Sent from my GT-I9000
Click to expand...
Click to collapse
Hi.
I just started with CWM-based recovery v5.5.0.4 and placed all above mentioned files/packages into the device internal SD card.
That's what i did :
1). Entered into the recovery mode menu by holding down Volume Up + Power and installed CWM-based recovery v5.5.0.4 zip from the selection of Internal SD Card .
2). After reboot, i came up again in Recovery mode using CWM-based recovery v5.5.0.4 application.
3). Now installed cm-9-20121011-ivendor-ariesve-rc5.zip by the navigation of "Install zip from SD".
It took hardly 4 to 5 seconds and displayed a message that it completes . no flash screen or anything came up and reboot.
4). After that installed gapps-ics-20120429-signed.zip by the navigation of "Install zip from SD".
It displayed same complete message but within 5 to 8 seconds i think.
5). I Wipe data/cache/Dalvik cache after above step and then again repeat the process.
After that i did Wipe data/factory reset and wipe cache partition.
Now when i try to start my device then each time it comes into the CWM-based recovery v5.5.0.4' s recovery mode.
Ask please i have tried too many things with it but yet not soft bricked.
I am able to switch into Download mode.
Soryuu said:
Hey,
Could you tell me what was unsuccessful about the install? Did it stop installing, did it bootloop, so on so forth?
But this is how I flashed CM9 onto my I9000, and I know that the I9001 is very similar so...
1.) You've got CWM, sweet. Boot into recovery. Make a bckup of your data through the option provided.
2.) Wipe data/cache/Dalvik cache. The first two are pretty simple to do, the last one is under "Advanced" settings.
3.) Now that you've got that, select "Install zip from SD". Navigate to where your CM9 file is. Select and confirm. Wait for it to flash in...
4.) At this point you might get a recovery bootloop. Don't panic here- just take out the battery, reinsert. Reboot into recovery. You should see that your recovery has been updated.
5.) Reselect the rom from the "Install zip from SD" option. This time it should start flashing in. Wait for it to finish, then it should reboot normally. Be patient as it boots up for the first time.
6.) Once you've done so, reboot into recovery again but this time select the gapps zip.
Unless the I9001 is different in a major way in terms of installing, that should work. I'm not quite sure...
Hope I helped
Sent from my GT-I9000
Click to expand...
Click to collapse
Perfectly simple guide! Thanks.:good:
The only thing I want to ask - what is the backup you have mentioned in point 1)? Is it back up of your personal data, or is it back up of your current ROM?
Hey man, glad I made it simple
Yeah, its a backup of your whole rom I believe- system apps, system files, all your downloaded apps all your data, so on so forth.
Helps you get back to what you were running before in case something goes wrong during installation.
Sent from my GT-I9000
---------- Post added at 02:29 PM ---------- Previous post was at 02:15 PM ----------
empnetsol said:
Hi.
I just started with CWM-based recovery v5.5.0.4 and placed all above mentioned files/packages into the device internal SD card.
That's what i did :
1). Entered into the recovery mode menu by holding down Volume Up + Power and installed CWM-based recovery v5.5.0.4 zip from the selection of Internal SD Card .
2). After reboot, i came up again in Recovery mode using CWM-based recovery v5.5.0.4 application.
3). Now installed cm-9-20121011-ivendor-ariesve-rc5.zip by the navigation of "Install zip from SD".
It took hardly 4 to 5 seconds and displayed a message that it completes . no flash screen or anything came up and reboot.
4). After that installed gapps-ics-20120429-signed.zip by the navigation of "Install zip from SD".
It displayed same complete message but within 5 to 8 seconds i think.
5). I Wipe data/cache/Dalvik cache after above step and then again repeat the process.
After that i did Wipe data/factory reset and wipe cache partition.
Now when i try to start my device then each time it comes into the CWM-based recovery v5.5.0.4' s recovery mode.
Ask please i have tried too many things with it but yet not soft bricked.
I am able to switch into Download mode.
Click to expand...
Click to collapse
Hmmm... Okay, I see...
What recovery did you start with before flashing CWM 5.5.0.4? Because I think what happens is that in whatever recovery you start with, you start by flashing in the CM9 file directly, instead of flashing a different CWM version in first.
So a good place to start would be back at 2.3.6 (don't know the firmware for the I9001). That can be done through download mode and Odin (If you need help with that feel free to ask). Then root again, get recovery back.
Flashing in the CM9 file the first time actually doesn't take long- maybe 5-10 seconds as you said, before bootlooping. What that bootloop does is it actually sets up a newer recovery, so that you can properly flash CM9 in.
Once you flash in the CM9 file the first time, try flash it in a second time. If it takes 4-5 seconds again then you have a problem, otherwise it should take a little bit for the file to install.
It will reboot; like I said in my little guide, just turn off, reboot into recovery and flash in Gapps, then let it boot.
Also, I don't think you need to wipe everything after the CM9 zip finishes. I didn't need to, and it worked fine...
Again, hope I helped
Sent from my GT-I9000
hi .
i am trying to give answer in point:
What recovery did you start with before flashing CWM 5.5.0.4?
-> yes i t was exactly CWM 5.5.0.4.
Because I think what happens is that in whatever recovery you start with, you start by flashing in the CM9 file directly, instead of flashing a different CWM version in first.
-> Could you elaborate the above sentence please? As long as i understood I initially installed CWM recovery through recovery mode by holding +Vol + Power+ Home.
So a good place to start would be back at 2.3.6 (don't know the firmware for the I9001). That can be done through download mode and Odin (If you need help with that feel free to ask). Then root again, get recovery back.
-> Yes i have been reverted through Odin Stock Gingerbread. How to root again? Could you please enlist in points?
Flashing in the CM9 file the first time actually doesn't take long- maybe 5-10 seconds as you said, before bootlooping. What that bootloop does is it actually sets up a newer recovery, so that you can properly flash CM9 in.
-> I don't think it's a bootlooping situation. When i start my device , It dispays CWM recovery screen each time even after the sucessull completion of CM9 and gapps,
Once you flash in the CM9 file the first time, try flash it in a second time. If it takes 4-5 seconds again then you have a problem, otherwise it should take a little bit for the file to install.
It will reboot; like I said in my little guide, just turn off, reboot into recovery and flash in Gapps, then let it boot.
-> I tried it many time right now and 2-3 months ago too but it took almost 20 - 30 seconds in first attempt.
Also, I don't think you need to wipe everything after the CM9 zip finishes. I didn't need to, and it worked fine...
-> I tried through Wipe and with it but could start my OS. Instead it display everytime a CWM screen.
=================================================================================================
In last , i did below steps :
1) Boot into recovery.
2) Wipe data/Factory reset.
3) Wipe cache.
4) Go to Advanced, then wipe Dalvik cache.
5) Go back, go to Mount & Storage, then Format System.
6) Go back, go to Install zip from SD Card => Choose zip from SD Card => cm-9-20121011-ivendor-ariesve-rc5.zip.
7) Do the same thing for the gapps zip.
8) Wipe data/Factory reset again (just to be sure).
9) Reboot.
Go into the cm10 thread by ivendor in developement section and in the middle of the 1st post is a download link for cwm 6.0.1.9. Flash it in recovery and reboot. The Problem should be gone.
Had the same issue.
Hope i helped
Hi Markey.
Do you mean that I 'll have to get CM10 and CWM 6.0.1.9 and then installed with same approach as i aforesaid?
Elaborate please if i misunderstood. Thanks
empnetsol said:
Hi Markey.
Do you mean that I 'll have to get CM10 and CWM 6.0.1.9 and then installed with same approach as i aforesaid?
Elaborate please if i misunderstood. Thanks
Click to expand...
Click to collapse
No i meant that you can install everything like in your guide and after that you install the cwm 6.0.1.9 and reboot, then you should be in recovery and then you have to reboot your phone and it should start normally
This solved it for me
Hope i helped
That's what I understood now:
0.5) Entered into the recovery mode menu by holding down Volume Up + Power and installed CWM-based recovery v5.5.0.4 zip from the selection of Internal SD Card .
1) Boot into CWM-based recovery v5.5.0.4 Recovery mode.
2) Wipe data/Factory reset.
3) Wipe cache.
4) Go to Advanced, then wipe Dalvik cache.
5) Go back, go to Mount & Storage, then Format System.
6) Go back, go to Install zip from SD Card => Choose zip from SD Card => cm-9-20121011-ivendor-ariesve-rc5.zip.
7) Do the same thing for the gapps zip.
8) Wipe data/Factory reset again (just to be sure).
9) Reboot
10) Then install the cwm 6.0.1.9 and reboot.
It could be solution, i will try and 'll tell at today night (after 6 hours).
It should be the right way but you can skip step 5 and 9
Hope i helped
empnetsol said:
That's what I understood now:
0.5) Entered into the recovery mode menu by holding down Volume Up + Power and installed CWM-based recovery v5.5.0.4 zip from the selection of Internal SD Card .
1) Boot into CWM-based recovery v5.5.0.4 Recovery mode.
2) Wipe data/Factory reset.
3) Wipe cache.
4) Go to Advanced, then wipe Dalvik cache.
5) Go back, go to Mount & Storage, then Format System.
6) Go back, go to Install zip from SD Card => Choose zip from SD Card => cm-9-20121011-ivendor-ariesve-rc5.zip.
7) Do the same thing for the gapps zip.
8) Wipe data/Factory reset again (just to be sure).
9) Reboot
10) Then install the cwm 6.0.1.9 and reboot.
It could be solution, i will try and 'll tell at today night (after 6 hours).
Click to expand...
Click to collapse
It should be the right way but you can skip step 5 and 9
Hope i helped
Dear Markey,
Whyn't should i start from cwm 6.0.1.9 rather than CWM-based recovery v5.5.0.4 .
Should i require to check from it or not? cwm 6.0.1.9 support cm-9-20121011-ivendor-ariesve-rc5.zip ?
empnetsol said:
Dear Markey,
Whyn't should i start from cwm 6.0.1.9 rather than CWM-based recovery v5.5.0.4 .
Should i require to check from it or not? cwm 6.0.1.9 support cm-9-20121011-ivendor-ariesve-rc5.zip ?
Click to expand...
Click to collapse
I don't know if cwm 6.0.1.9 supports cm9 but it should.
You could try it out and tell me back
when i go in advance and select wipe dalvik cache option.
it display an error:
E:unknown volume for path [/sd-ext]
Dalvik Cache wiped.
After completion of each step, i tried again but still not start OS.
empnetsol said:
when i go in advance and select wipe dalvik cache option.
it display an error:
E:unknown volume for path [/sd-ext]
Dalvik Cache wiped.
After completion of each step, i tried again but still not start OS.
Click to expand...
Click to collapse
Got the same error, i think its normal
Ok, then flash this file: http://forum.xda-developers.com/attachment.php?attachmentid=861538&d=1326841043 in recovery, reboot and tell me back if it works
Or you could try this way if the other isn't working: http://forum.xda-developers.com/attachment.php?attachmentid=928219&d=1330695090 its the stock recovery, flash it in recovery and reboot and tell me back. I think you should first try stock recovery and then the other file. Sry for the wrong order
Hope it will work again
hi markey.
how to flash these files? i didn't understand the flashing word.
Got an error from mentioned recoveries.
Installing update...
E:Error in /tmp/sideload/package.zip
(Status 2)
Installation aborted.
empnetsol said:
hi markey.
how to flash these files? i didn't understand the flashing word.
Click to expand...
Click to collapse
empnetsol said:
Got an error from mentioned recoveries.
Installing update...
E:Error in /tmp/sideload/package.zip
(Status 2)
Installation aborted.
Click to expand...
Click to collapse
I mean that you have to install them via recovery with install update from sd card or with install zip from sd card -> its called flashing
And i meant that you have to install the first file first and reboot and if its not working when you reboot then install the stock recovery and then the problem should be solved. But then you have to flash the cwm recovery everytime you want to flash something like a new kernel or a custom rom
Hope i could help
Markey,
I did the same as you are saying and got the above error on each file.
Could you explain the below linw please ?
But then you have to flash the cwm recovery everytime you want to flash something like a new kernel or a custom rom
What i 'll have to do now?
empnetsol said:
Markey,
I did the same as you are saying and got the above error on each file.
Could you explain the below linw please ?
But then you have to flash the cwm recovery everytime you want to flash something like a new kernel or a custom rom
What i 'll have to do now?
Click to expand...
Click to collapse
Which recovery do you use?
Cwm or stock recovery?
If you use stock then you have to reboot without installing one of the files and the problem should be solved
I meant that if you want to install another kernel or custom Rom you have to install the cwm recovery because its better then stock and after installation of the Rom or kernel you have to reinstall the stock recovery
If you don't understand i'll write you a guide for what you have to do
Hi All,
I was on Omni Rom 4.4.2. today I downloaded CM Nightly 10.2. Placed it on the SD card..rebooted into recovery. Wiped data, cache everything and then ran the CM ROM file to install from zip.I got a warning that said installation failed. Now i don't have any ROM as i did a full wipe. When i try to mount USB storage..nothing happens. I have TeamWIn recovery. I don't knwo what to do now. Please help.
harry92008 said:
Hi All,
I was on Omni Rom 4.4.2. today I downloaded CM Nightly 10.2. Placed it on the SD card..rebooted into recovery. Wiped data, cache everything and then ran the CM ROM file to install from zip.I got a warning that said installation failed. Now i don't have any ROM as i did a full wipe. When i try to mount USB storage..nothing happens. I have TeamWIn recovery. I don't knwo what to do now. Please help.
Click to expand...
Click to collapse
If you have an sd card it will be easier. Just load a working rom in it using computer. Otherwise, there seems to be a sideload option in twrp, but i have not tried.
forest1971 said:
If you have an sd card it will be easier. Just load a working rom in it using computer. Otherwise, there seems to be a sideload option in twrp, but i have not tried.
Click to expand...
Click to collapse
Sideloading is simple
go to advanced settings and enable sideload.
connect phone to pc and open command prompt.
run command
adb sideload "name of zip"
this should install the zip... may be the CM10.2 you downloaded was a bad zip. download again and match md5.
So, i was flashing cm13 and everything went well until i did something stupid. I accidentally wiped the newly installed system because i thought it said 'wipe system cache' but it said 'wipe system' only. I was using cm recovery. I erased the zip file after i flashed so i dont know what to do anymore. Please help me!. i can still go into recovery and fastboot mode and thats all....
Push a ROM file through adb. In TWRP, there's an option called "adb side load". Use that.
Or mount OTG in TWRP to flash a ROM.
if you have TWRP, just turn it on using the specific combination of the keys. Then directly connect to the pc using the data cable and it will show the internal storage of your device. Copy the cyanogenmod 13 from your pc and flash it. Peace!!
Download tool in original android development thread and go into fastboot mode connect to PC and in tool chose option flash cm 12.1 .....it Dow. Required files than flash it by enter
And its done
Os file is approx around 1gb