Hello, I have a PINENG PN-989 20000mAh Power Bank. When I try to charge it from the 2.1a port it does not charge (Shows a red X over the battery icon and shows as USB charger in Ampere) When I plug it in the 1a port on the same power bank it does charge (Shows a lighting icon over the battery bar and shows as AC Charger in Ampere)
I was wondering if anyone knows why it is behaving this way and if their is anything I can do to make it charge at 2a.
If I understand correctly the power bank is not able to charge at 2.1a port, have you tried using a different cable to see if it helps? The only other thing I can think of is it being a fake but I've never read of that being an evident factor. Or it can just be faulty. Would trying getting it replaced if your still under any warranty.
I try using a shorter cable (1.5f) and now the 2.1a port works as ac when charging. The official 5f cable still shows it as USB charging with a red X on the battery bar.
You can use different cables or devices to test
Related
I have a tilt that now will charge from the USB to computer connection, but does not charge when plugged into the wall with my wall charger (an after-market charger that worked fine until today). The phone says "charging" but actually loses battery power .. and after a while the orange charging light goes off.
Any thoughts -- sure is a drag to have to charge my phone through the laptop.
What after market wall charger do you have? Does it use the USB cord to charge? I'm assuming that you plug the USB cord into the wall charger and then into your phone. If so this will not work. The USB cable is only capable of trickle charging. If you are doing anything while it is charging over USB you will use power faster than the trickle charger can provide. You have to charge it with a wall charger that does NOT use the USB cable.
Yes I realize that the standard wall charger uses a mini-USB plug but the internals of the cable are not the same as a data USB cable. The difference in juice it can provide is like comparing a PVC pipe to straw.
I was just using a radio shack iGo charger with a usb tip ... it worked fine until my latest ROM upgrade.
Ahh I see. Yep the charger is most likely bad.
I'm looking for an extra charger for my nc. What I need to know is what is the mah output of the stock changer so I can get one that had the same rating. Our can someone link me to a cheap stock charger.
The output is 5volts / 1.9 Amperes.
Edit, it is written on the charger btw, you could probably have checked that your self .
Where can I get a charger with the same specs? I don't want to spend $20 but if I have to I will just buy another stock one.
I have a 5v 700mah charger that I bought for my phone. Will that work or is the rating to low?
That will work, it just wont charge as fast...
Sent from my NookColor using XDA app
FYI: I tried using my HTC usb charger with the nook usb cable and it will not charge. The charging light flickers.
Thats what I'm worried about
There is this cable from boxwave with a dongle off the end that you are supposed to use to charge from USB chargers. Why would anyone need this?
http://www.boxwave.com/products/dir...arge-cable-barnes-_-noble-nook-color_4101.htm
Mike
nrune said:
There is this cable from boxwave with a dongle off the end that you are supposed to use to charge from USB chargers. Why would anyone need this?
http://www.boxwave.com/products/dir...arge-cable-barnes-_-noble-nook-color_4101.htm
Mike
Click to expand...
Click to collapse
It looks like one end is for transferring data only and the other is for charging only
I just tried the charger I have that works with my phone and it wont charge my NC. When I plug it in nothing happens it doesn't even recognize its plugged in
boxwave.com/products/wallcharger-direct/barnes-_-noble-nook-color-wall-charger-direct_4101.htm
That looks like it will do the job perfectly and is only $13
xxosynrgoxx said:
FYI: I tried using my HTC usb charger with the nook usb cable and it will not charge. The charging light flickers.
Click to expand...
Click to collapse
It is charging, just not as fast and the device doesn't notify you of it. HTC usb wall plug chargers are usually 5volts and 1amp, the nook requires 1.9 amps to charge properly.
/mr
There are no spec listed for that charger so it could be a 700mah or it could be a 1.9a charger.
How many of you guys recommending underpowered chargers actually have any electronics background?
The nook charges when connected to a usb socket on a computer, which provides 500ma as a high power device. So your 1000ma charger is twice as good as using a computer.
In order to get 1900 ma, the nook isn't using stock usb stuff in the charger... but normal usb works just fine because, well, the standard requires it to...
4000 mAh battery should charge fully in 2 hours on the nook charger, 4 hours on the htc charger, or 8 hours on a computer...
Sent from my NookColor using XDA app
Good to note that there's a bug on the NC that makes it appear that it's not charging, when connected via USB connection, but it really does charge.
regular micro usb chargers from cell phones will charge the nook even when it says it's not charging.
Novarider said:
I just tried the charger I have that works with my phone and it wont charge my NC. When I plug it in nothing happens it doesn't even recognize its plugged in
Click to expand...
Click to collapse
The NC will charge from my Droid's power adaptor even though it does not show it to be working. It will take a lot longer to charge with a standard 0.5A USB power adaptor.
In theory, it should take about 4 times as long to charge from standard USB instead of the B&N charger.
Novarider said:
I just tried the charger I have that works with my phone and it wont charge my NC. When I plug it in nothing happens it doesn't even recognize its plugged in
Click to expand...
Click to collapse
It does work. It's just charging slow so you can't necessarily tell. Also. There will be no indicators on the nook to show that it is charging but i'm pretty sure it is. Leave it plugged in overnight and see.
2A rated USB adapter for under $10: http://www.madvapes.com/2-amp-AC-to-USB-Adapter-ideal-for-Passthroughs_p_2357.html
I own one and can confirm it works perfectly.
Hi,
a friend of mine have gifted to me a car charger that is incompatible with my Legend, because is miniusb (with output: 5V - 1.5A) and the regular charger in bundle with the phone is microusb with output: 5V - 1A.
Can I use the car charger, with a differte cable (the car charger can use usb cables), or the current in output is to much for the phone?
It doesn't actually matter how powerful the PSU (power source unit) is, even if it was 5V / 10A you could still use it... To put it to easy talk, the phone will just take what it needs. The important parameter is Voltage, which is OK - 5V
Dr.Romca said:
It doesn't actually matter how powerful the PSU (power source unit) is, even if it was 5V / 10A you could still use it...
Click to expand...
Click to collapse
That's not quite true. The power does matter, but only in a limited way. The voltage (volts) must match. The current (amps) or power (watts) rating of the supply must be at least that which the device draws.
So in this case; yes, you are absolutely fine. You just need an adaptor to make the plug fit.
My work phone has a mini-USB socket, but requires 1.5A to charge successfully, which is three times as much as standard USB. My personal phone has the same socket, but will charge when connected to a conventional USB host like a laptop, which only supplies up to 0.5A. I can use any USB charger with my own phone, but I can only charge my work phone from its own charger.
Apparently I've not made enough posts to include links, but you can google "Charging Batteries Using USB Power - Maxim" and click on the first link, as long as you don't mind reading a moderately technical document.
Don't nitpick I'm an engineer so I know how these things work end to end, If you have power and a good charger (not meaning the car charger, but the actual charging circuit handling the battery charging inside the phone) you can charge even from 5V / 200mA It'll just take more time, of course you'd have to add more than the phone consumpts, but if you do that you're basically OK...
What you're referring to is USB charging, we all know USB doesn't have to have full 5V but in case of charger, there will be 5V...(possibly even more when open)
I have this car charger with 5V and 1000mAh
http://www.ansmann.de/cms/de/consumroot/chargers-and-power-supplies/universal-chargers/carcharger-micro-usb.html
and i must say it is worse than the Original charger for the Wall outlet from HTC -- it takes about twice as long to charge the phone.
And when i use my phone for Navigation it even slowly discharges the phone - which is truly annoying!
EDIT:
I did some research: on original HTC Chargers the Data+ and Data- pins on the micro-USB-connector are short-circuited to tell the HTC-Phone that it connected to an original charger - only when the phone realizes this, it charges with 1000mA!!! Otherwise it only charges with the USB-specificated 500mA
You can easily check this when you charge your Phone with a 3rd-Party charger, go to:
Settings-> Telephone-Status -> Battery
Here is usually written charging (USB)
only with original chargers you get "charging" (AC)
I opened the connector of my Car-charger and short-circuited the Data+ and Data- --> Now it says charging (AC)
I still have to test if charges faster now, and charges the phone while navigation - because until now it discharges while navigation, despite being connected to the Car-charger.
So to say it short: If you want to quickly charge your phone in your car buy a original HTC Car charger, or short-circuit a 3rd-Party one.
f4b1ck said:
Hi,
a friend of mine have gifted to me a car charger that is incompatible with my Legend, because is miniusb (with output: 5V - 1.5A) and the regular charger in bundle with the phone is microusb with output: 5V - 1A.
Can I use the car charger, with a differte cable (the car charger can use usb cables), or the current in output is to much for the phone?
Click to expand...
Click to collapse
don't worry you can charge your phone with no problem
i have the same 5V 1.2 A ,it's charging with no problem
It's good to have stornger charger. Probably you wil be able to charge your phone faster But it always have to be 5V.
So this is my first motorola and I had heard of the issues they have with non motorola chargers. Now I am experiencing it first hand. With the same ac charger I have charged many phones with and is capable of 1 amp output (D4 charger is only rated at 850 mA) my D4 struggles. With the device off it charged painfully slowly. While on it cannot even charge. It discharges while plugged in despite the charging indicator and reporting "charging (AC)" in status.
How does it know it is not a moto charger? Is it just about the resistance between the data pins? For most other phones shorting the data pins on the charger indicates to the phone that it is a high current charger and not a computer USB port. Is there a similar trick for motorola phones? I would rather not have to purchase an overpriced moto oem car charger. I have a perfectly fine 1.2 amp car charger soldered directly into my car's 12v system behind the dash. Can I make it work?
Thanks!
On a regular basis I successfully charge my D4 using both a charger from a Samsung Reality feature phone and from a B&N Nook Simple Touch, in addition to the one that came with it. I've also used a variety of car chargers.
Sent from my DROID4 using XDA
Actually, so far I have only one charger that had any trouble charging the phone (it was a $3 charger with 2 USB ports), but the $3 charger with ONE USB port works fine, as does the Nook Color charger, Blackberry charger, and Samsung charger I have tried it with, as well as both my old car charger and Lenovo's always-on charging port on their laptops.
JKingDev said:
So this is my first motorola and I had heard of the issues they have with non motorola chargers. Now I am experiencing it first hand. With the same ac charger I have charged many phones with and is capable of 1 amp output (D4 charger is only rated at 850 mA) my D4 struggles. With the device off it charged painfully slowly. While on it cannot even charge. It discharges while plugged in despite the charging indicator and reporting "charging (AC)" in status.
How does it know it is not a moto charger? Is it just about the resistance between the data pins? For most other phones shorting the data pins on the charger indicates to the phone that it is a high current charger and not a computer USB port. Is there a similar trick for motorola phones? I would rather not have to purchase an overpriced moto oem car charger. I have a perfectly fine 1.2 amp car charger soldered directly into my car's 12v system behind the dash. Can I make it work?
Thanks!
Click to expand...
Click to collapse
Not sure how it knows one way or the other. I've successfully used a few LG chargers to charge my D4. The only really hickup I've ran into is the usb cables from those lg chargers won't sync data to the phones when plugged into a computer, they'll still charge off the usb port but won't read as a usb connection to the computer.
Heh, captcha is trynply.
Every charger I've used, including an old charger for an EN-V, kindle, supplied, and various other phone chargers works just fine with this phone. Probably have a bad charger, guy.
Thanks for the replies. I guess I was wrong. My modded car charger works just fine. I guess its just time to retire the old charger that I have been using. I think it might be my old nexus one charger.
A more important question would be does the thing charge over computer-bound USB ports?
When you're without a charger, but there's a USB cable that fits your phone, sometimes a regular USB data port is the only that is around... even though it might take a really long time.
Try a computer bound USB port, then try your actual charger, again. Or do the hard reset (vol down plus power, hold until it actually does it), which is just like pulling the battery.
See how that goes.
Chris
RueTheDayTrebek said:
A more important question would be does the thing charge over computer-bound USB ports?
When you're without a charger, but there's a USB cable that fits your phone, sometimes a regular USB data port is the only that is around... even though it might take a really long time.
Try a computer bound USB port, then try your actual charger, again. Or do the hard reset (vol down plus power, hold until it actually does it), which is just like pulling the battery.
See how that goes.
Chris
Click to expand...
Click to collapse
It does in fact charge via USB port. In fact, it has a 'charge only' mode. Depending on how much juice your port puts out, and what you are doing with the phone, it will charge slowly/not at all, though.
from my experiences, the droid 4 will not accept lg microusb cables, the charging bricks work tho. i use a blackberry microusb on mine along with a Logitech and the stock moto ones. 1.2 amps is a bit high but not crazy sounding. personally, I charge at 1 amp.
Looking at this article it seems like an upgraded cable could charge a device faster. If the phone shows "Fast charging" can that be improved upon? Could a USB PD cable charge faster? Is the cable that came with the phone the best?
It is true that the cable intervenes with the charge the battery receives, but, in the end, there is a limit in the charge the charger itself can supply
I have used a couple of different USB Type-C cables that are said to be suppose to offer much faster charging speeds than the bundled stock Samsung Type-C cable. Honestly I don't notice a difference in charging speeds.
The real proof is always testing with a USB wattmeter and a phone that has less than 80% charge (screen-off).
The most I get out of a stock charging brick and a Anker Type-C cable is 18 Watts. Stock cable gives me 16 Watts under the above conditions