hello i have the p9 3 days ,i has officiel ota update 167 install ,the p9 has this install after update .reboot devices
will wont to start the p9 dosnt start recovery ,dosnt start system ,dosent start erecovery its stuck on logo.
now my question we can i fix it ,hsuit dont work.
only fastboot work. i have with fastboot flash firmeware 166 .system,cust ,boot and recovery .stock rom and and and
nothing help
fastboot say flash ok and writing.
fastboot enter rescue mode stuck .
sry for my bad english
Related
Phone Info:
Huawei P7 L10
android 4.4.2
emu 2.3
b126 official firmware
rooted
i changed a boot animation in romtoolboxpro from 800x800 to 1080x1920 and installed to my device, clicked the preview option and it wroked but when i rebooted i was left with an error message in place of my recovery, and i cannot boot up the phone normally. or at all for that matter. i can go into fastboot&rescue mode, and it shows that my bootloader is still unlocked but i have no way to flash the recovery img to my system, so my phone is currently a brick. HELP!!!
Sir,
Please wait until mods will move this thread to the device specific forum for more relevant answers.
Stand by
Good luck
Ryan_Again said:
Phone Info:
Huawei P7 L10
android 4.4.2
emu 2.3
b126 official firmware
rooted
i changed a boot animation in romtoolboxpro from 800x800 to 1080x1920 and installed to my device, clicked the preview option and it wroked but when i rebooted i was left with an error message in place of my recovery, and i cannot boot up the phone normally. or at all for that matter. i can go into fastboot&rescue mode, and it shows that my bootloader is still unlocked but i have no way to flash the recovery img to my system, so my phone is currently a brick. HELP!!!
Click to expand...
Click to collapse
u can flash bootloader.img via adb ..
my Huawei p7 only turns on in fastboot, how can I make it work normally?
it doesn't turn on recovery mode or in any other mode than fastboot
what can i do?
craescu said:
my Huawei p7 only turns on in fastboot, how can I make it work normally?
it doesn't turn on recovery mode or in any other mode than fastboot
what can i do?
Click to expand...
Click to collapse
Please provide more information - is the ROM the stock one? Did you flash a recovery? Did you flash a bootloader? Is the bootloader locked or unlocked?
g4b3rm4n said:
Please provide more information - is the ROM the stock one? Did you flash a recovery? Did you flash a bootloader? Is the bootloader locked or unlocked?
Click to expand...
Click to collapse
Most Probably Flashed Wrong Boot or Recovery img ... or used some other rom ..... Like L05/L07 rom on L00
I flashed [ROM] Se7en-Rom v3.8 / EMUI 3.0 / 4.4.2 / B602. after I flashed CWM flashable from recovery B609 for P7-L10 .after I wanted to go back and have left the mess .from fastboot I flashed all boot and recovery possibile but nothing. continuing to turn back with Huawei logo or just in fastboot
craescu said:
I flashed [ROM] Se7en-Rom v3.8 / EMUI 3.0 / 4.4.2 / B602. after I flashed CWM flashable from recovery B609 for P7-L10 .after I wanted to go back and have left the mess .from fastboot I flashed all boot and recovery possibile but nothing. continuing to turn back with Huawei logo or just in fastboot
Click to expand...
Click to collapse
Flash the recovery from here. This is the official recovery for B609.
After that, download B609 full official ROM, and put it on the SD card in a folder called dload. (Note: the file is probably zipped - the only thing you need is a file called update.app.)Start the device by holding all three buttons. Force update should commence and you should get a usable, fresh official B609.
i tryed to do what did you said but it didn't work
thank you anyway
I tried everything you guys .According you can run again? bootloader and unlocked I have done everything with PC bootloader. but with the usual commands (flash boot, recovery.system.cust.userdata) caisson other commands that you can do? you can say if you can restore or abandon so?
Did you try to flash cwm 2.8.1.0 then flash MyROM 3.3, then flash full version B609?
Hey all. I was trying to rollback my P9 to a stock ROM, but it failed and now I am stuck with a bricked P9 (bootloop).
My phone is a European P9 (EVA-L09C432). I have an unlocked bootloader.
- Huawei eRecovery and HiSuite restore does not work.
- I've tried forcing the update using the SRK Tool brick utility, but receive the message "FAILED (remote: sparse flash write failure)" when it's strats writing 'system'.
- My TWRP backup does not work, I had a 7GB backup that installs fine, but the phone is still stuck in a bootloop.
- I can flash EVA-L09C432B378 ROM using the SRK brick utility fine, but the phone is still stuck in a bootloop.
- After I have installed B378 and try to force flash B136 using the dload method, it either gets stuck on the "going into restore mode" or it goes to the "installing package" screen, where it is stuck at 5% until it reboots.
Any suggestions?
try one more time install rollback package by download mode
I've tried. Several times, all day :crying: My process:
Write TWRP from fastboot so I can boot into TWRP and transer UPDATE.app to the dload folder
Reboot into fastboot
Write stock recovery image from fastboot
Boot into recovery mode
Get stuck at 5% on the "Installing update" screen.
I've tried the UPDATE.app or firmware B136 (stock), and UPDATE.app for B378 (Nougat)
Both get stuck at 5%.
I'm stuck at the bootloop
isn't srk tool only for MM?
maybe try extract recovery , boot and system partition from b378 and flash by fastboot , next start flash rollback package by download mode
I noticed when I tried to restore my backup using TWRP it failed at "vendor" (Failed to wipe vendor). I receive this issue at vendor and product.
I tried using fastboot to flash vendor and product manually, I receive these error messages:
"failed: remote command not allowed"
The phone won't allow me to write vendor and product.img... but my bootloader was unlocked?
Is it possible I could have relocked my bootloader? How am I supposed to get the bootloader code for my P9 again :/ It's nearly impossible.
I managed to use the recovery dload method to install a beta version of B378 (build number NRD90M test-keys). Will now try to use the recovery method to roll back to B136 and update back to B378 again.
Highfall said:
I managed to use the recovery dload method to install a beta version of B378 (build number NRD90M test-keys). Will now try to use the recovery method to roll back to B136 and update back to B378 again.
Click to expand...
Click to collapse
I'm having similar issues. Have you solved your problem? What have you tried so far?
Same problem here! Did you resolve?
Thanks you.
Try unplug charger or usb cable then do it
WTF, that ist the solution to the whole damn problem! Just unplugging the damn usb cable and it installs the update just fine. ive spend 2 whole days on this, almost giving it up beacuse everytime it got stuck at 5% and then this...
seriously thank you!
JimmyEatFood said:
Try unplug charger or usb cable then do it
Click to expand...
Click to collapse
thx i managed to boot my device, but i relocked bootloader and factory reset doesnt work correctly it deleted 3rd party apps and leaved few system apps and blotware. what should i do.
and really thanks, you saved me.
Removing cabled worked for me also
Situation
Currently I am running VIE-L29C636B320, with EMUI 5 and Android 7.0. The phone is runs fine
So when I am to install , boot to recovery mode:
It gives
"Your device is booting now... "
And stuck there forever. I can get my phone back to working state by rebooting 3 times.
I tried the following methods..
> using dload+**#*#2846579#*#*, )
> I currently cannot boot into TWRP at all (I am using TWRP3.1.1 for Huawei p9 plus already), and all the key combinations doesn't work.
> Firmware Finder with Proxy Add-on
> fastboot flash reccover twrp.img (phone oem unlocked already)
> Huawei e-recovery does not detect any packages to download.
So I suspect something wrong with my img files..
My plan is:
Using Huawei Extractor to extract all img's (system, boot custom and recovery) from B360
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash cust cust.img
fastboot flash system system.img
It took me a while to get to where I am now from EMUI 4.1. What I don't want to is lose my working phone and make my phone completely useless.
So my question is, are the above steps no u-turn and I would completely screwed? Or safe to get those img's back and then I should be able to continue to upgrade from B320 to 362 and onwards?
Since I cannot boot into TWRP, I can't take backup of my phone..
I used firmware finder to udgade nougat to oreo on my P10. I used VTR-L29... which the app said was okay for my device, now i'm stuck on the Huawei eRecovery page but when i try to press download latest... it doesn't work, i'm stuck in a loop. My problem is that I have a backup, but I dont have TWRP installed...
I'm really stuck... can someone help?
Use firmware finder for pc and push the update by proxy and then Erecovery should work.
It's your phone branded?
And don't forget to push with the same version that you had before trying to flash with ff