hi, my mi3 fully charged and still cant on. It cant load recovery mode and fastboot mode:crying::crying:
pls tell me what to do
I think the only option would be edl mode. Since you can't access fastboot, then that means you'll have to check for test point method to get into edl mode (or if there's another way I don't know of). Once you are in edl mode, follow this thread.
Related
Hi everyone,
I have bricked nexus 6. It has a locked bootloader plus no bootloader, no recovery, no system no nothing.. If i boot up the phone it goes into bootloader kind of thing and pc can recognize it as a fastboot device but since it has locked and corrupt bootloader there is no command i could get it to run anything.
I know most of you think its simple bricked and cant work it again but refuse to believe that just because the simple fact that i couldnt get any answers from anyone relavent to this. I have been using android for years, basically from the beginning, i know i am not a developer but i think i know few things and i been in similar situations before but this is the first time i got stuck. I know it can be done since its a qualcomm device. There should be a way to put the device in edl mode flash with qfil or something. I know all the post about these kind issues i read them all. Whenever somebody asks about how to put it in edl mode the answer is always go check that post about how to recover from edl mode. Please understand i need to put it in edl mode first to get it out of there.
So if anyone knows a way to put this device in edl mode please help so i can try to recover from there..
I already tried modified fastboot so it can run "fastboot reboot-edl command" it doesnt work for me.
I also tried a custom cable for triggering edl mode on xiaomi devices. But it doesnt work either.
The only other way i know is the short test points on the board or on the chips legs itself.
Like i said there may be no way because the lack of information out there if it is please say so so i can rest
Thank you for your time patience.
The best I can do is point you to [FIX] fix hard brick / qhsub_bulk after bad flash / cm12 flash from 5.1
If memory serves, there was a point when the adb reboot edl was patched in an upgrade. That was rather late in the device's supported lifetime. Maybe when Pie came out?
when i try to change from CN to WW i try flash file one by one for example fastboot flash boot boot.img all file same like this
and after flash phone cant go to fastboot only EDL mode i want help to try to Flashing Raw Firmware In EDL Mode Port 9008
please anyone help me
kimoalex said:
when i try to change from CN to WW i try flash file one by one for example fastboot flash boot boot.img all file same like this
and after flash phone cant go to fastboot only EDL mode i want help to try to Flashing Raw Firmware In EDL Mode Port 9008
please anyone help me
Click to expand...
Click to collapse
So you're saying that you no longer even have fastboot? I haven't even seen edl mode on our device,, only fastboot, recovery etc.
reg66 said:
So you're saying that you no longer even have fastboot? I haven't even seen edl mode on our device,, only fastboot, recovery etc.
Click to expand...
Click to collapse
i dont know what happened now i want any solution
kimoalex said:
i dont know what happened now i want any solution
Click to expand...
Click to collapse
If you cannot reach fastboot mode, sorry, but I don't know what else to suggest. I do not know how to fix from edl.
So just to check, can you get fastboot mode or not?
i cant get fastboot mode only edl mode
Were you able to fix??
Guys I was trying to do unlock my ROG Phone II with EDL mode:
https://forum.xda-developers.com/rog-phone-2/how-to/how-to-unlock-rog2-phone-via-edl-mode-t4008267
My phone is still in edl mode it shows as a COM port in my pc. I really need help I cannot do anything. I tried to flash it in MiFlash and it gives an error every time. Please help me!!!!!!!! PLEASE!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
I NEED HELP IMMIDIETELY PLEASE
The app works just fine... Also why are you trying to use a Xiaomi flash tool on an Asus device?
Get out of EDL mode with vol- vol+ power all three together.
EfeKamil said:
Guys I was trying to do unlock my ROG Phone II with EDL mode:
https://forum.xda-developers.com/rog-phone-2/how-to/how-to-unlock-rog2-phone-via-edl-mode-t4008267
My phone is still in edl mode it shows as a COM port in my pc. I really need help I cannot do anything. I tried to flash it in MiFlash and it gives an error every time. Please help me!!!!!!!! PLEASE!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
I NEED HELP IMMIDIETELY PLEASE
Click to expand...
Click to collapse
Have you tried doing the process with the correct drivers installed? (I have not done this method, but it could be driver related) See here for drivers
EDIT: at the bottom of your EDL thread it does state you need the Qualcom drivers installed, not sure if they're the same as the ones i linked to, but the ones in that thread are here
Also, this post may be of some use to you, might wanna read the rest of the thread too for tips...
'I read somewhere that you must start the EDL unlocking process as soon as you run the fastboot command to boot it into EDL mode. It wouldn't run correctly for me at first, but then I rebooted into fastboot, ran the enter dload command, then immediately ran the unlocker (or if it fails because your device hasn't entered EDL mode just yet, keep spamming it).
I have no idea why that's the case but it worked for me.'
So my phone's stuck in fastboot mode, oem unlocking and usb debugging is off, recovery mode doesn't work, and a custom rom was installed when bootloader was turned off, so is there any way to at least get the phone back to stock, or is it just useless now?
Since your phone is Qualcomm based, then you should have EDL mode in your device.
Have you tried it? There are multiple ways to boot into EDL mode, like adb reboot edl or the EDL cable method.
I don't know if it is unlocked by default on your device or you need unlock key first though.
If it requires unlocking then you have to send your device to an authorized service center, not just any service center.
If it doesn't then you can easily find guides on the internet about how to unbrick your phone with EDL mode.
Goodluck.
XDHx86 said:
Since your phone is Qualcomm based, then you should have EDL mode in your device.
Have you tried it? There are multiple ways to boot into EDL mode, like adb reboot edl or the EDL cable method.
I don't know if it is unlocked by default on your device or you need unlock key first though.
If it requires unlocking then you have to send your device to an authorized service center, not just any service center.
If it doesn't then you can easily find guides on the internet about how to unbrick your phone with EDL mode.
Goodluck.
Click to expand...
Click to collapse
Yeah I've tried entering it with the command, didn't work, but I suppose I could send it to a service center for it to get unlocked. I've heard other people have their phones enter EDL mode and other people saying it's basically useless though which was why I was slightly scared about entering it but I'll give it a shot, thanks.
Jaideus said:
Yeah I've tried entering it with the command, didn't work
Click to expand...
Click to collapse
EDL mode doesn't have a UI, if you enter the command and get black screen instead chances are that you're already in EDL mode.
Similarly if you turn off the device and leave it like that for a couple of minutes, some Qualcomm devices can detect that it's bricked and enter EDL mode automatically.
Alternatively you can just make your own EDL cable to force your device to boot to EDL mode, follow this thread here.
Or just get an EDL cable, they're cheap really.
Jaideus said:
I've heard other people have their phones enter EDL mode and other people saying it's basically useless
Click to expand...
Click to collapse
EDL mode is very low level and very powerful, you can literally do anything to your device with EDL mode the sky is the limit. However it requires special Qualcomm EDL tools which depend on your Qualcomm type (sahara or firehose) and correct driver.
Beware that EDL mode commands are very powerful and can mess anything beyond repair. So be careful with whatever command you use while in this mode if you're not sure what it does then don't use it. And send it to an authorized service center instead.
You can extract data with EDL mode and I recommend doing that before flashing anything.
Be careful of unofficial EDL tools, most are just trojans for the desperate.
The official tools are already on the internet. I don't recall the exact name but i think it was something along "QSPT" or something. Sorry for not being of much help.
I'd have searched for the correct tools for you, but it's getting really late here.
XDHx86 said:
EDL mode doesn't have a UI, if you enter the command and get black screen instead chances are that you're already in EDL mode.
Similarly if you turn off the device and leave it like that for a couple of minutes, some Qualcomm devices can detect that it's bricked and enter EDL mode automatically.
Alternatively you can just make your own EDL cable to force your device to boot to EDL mode, follow this thread here.
Or just get an EDL cable, they're cheap really.
EDL mode is very low level and very powerful, you can literally do anything to your device with EDL mode the sky is the limit. However it requires special Qualcomm EDL tools which depend on your Qualcomm type (sahara or firehose) and correct driver.
Beware that EDL mode commands are very powerful and can mess anything beyond repair. So be careful with whatever command you use while in this mode if you're not sure what it does then don't use it. And send it to an authorized service center instead.
You can extract data with EDL mode and I recommend doing that before flashing anything.
Click to expand...
Click to collapse
Yeah for the first part when I did the command it just said "unknown command" so nothing happened, but yeah I was thinking about getting an EDL cable, would any cable work or would only a specific type work? Also how would you know what the qualcomm type is?
Jaideus said:
would any cable work or would only a specific type work? Also how would you know what the qualcomm type is?
Click to expand...
Click to collapse
I worded this poorly my bad, what I meant is sahara and firehose are actually firmware boot type and it doesn't matter what tool you use as long as it is meant for Qualcomm devices.
Any EDL cable should work, and as for the tool it's QPST or QFIL.
As for the driver: Qualcomm driver link.
They say QFIL is much easier to deal with as it is standalone, anyway both work similarly.
As for the deep flashing process, you can follow this guide here.
The guide has updated driver, QPST and QFIL links.
For the firmware images I only found this one and it doesn't have Qualcomm firmware in it, in case you need Qualcomm firmware you need to follow the guide I gave you to extract the firmware from another RP2. Here is a video guide on how to extract qualcomm firmware with QFIL.
EVERYTHING I JUST SAID IS TESTED, HOWEVER I DON'T HOLD ANY RESPONSIBILITY SHOULD YOU PREM-BRICK YOUR PHONE.
Hope i helped. And goodluck.
I forgot to tell you how to use EDL mode to extract data, here is an article.
It might be hard to understand at first but you'll get used to it. It's completely safe so you can mess around as much as you want, Don't click random buttons though. Note that: The openpst tool isn't a flashing tool and only meant to communicate with Qualcomm devices in EDL mode.
Here is a different method, although it's meant for Xiaomi devices it's still generally for Qualcomm devices.
Just follow step 7 only. Obviously you won't be using MiFlash nor flash a MIUI ROM.
After flashing the ROM flash a custom recovery to backup your data.
Then delete all data including dalvik cache.
I can't confirm if those methods are tested so follow them on your own risk. However I suggest trying the second method since the extracted data from the first method would be encrypted therefore useless. Unless you know how to decrypt it.
Hello, I've tried everything about my bricked redmi 4x, i can't get it out of qualcomm 900e. I've done test point method, edl mode method and all combinations of them. I've also read this thread and nothing helped. The reason of brick is installing unofiicial rom. Is there any chance to make him alive?
Ok, i finally get into fastboot mode, but my bootloader is locked, is there any way to unlock it? I've tried a lot of programs, but bootloader status is still false.
hi there! i also have the same problem. im stuck at edl mode, 900e , sahara mode, can u help me how to get into fastboot mode?
I was trying to get out of 900e mode like 1000 times and then i succeed to get into fastboot mode and it worked (i don't know why it didn't work earlier). Now i can't boot a new os because the bootloader is locked and i don't remember mi account password (trying to log in by xiaomi mi tool v2).
i manage to get out of 900E mode, by looking for a test point on my device, opened her up and look for the test point jumper, kinda pretty easy. dropping this method here in case someone got hard bricked.
kubsde said:
I was trying to get out of 900e mode like 1000 times and then i succeed to get into fastboot mode and it worked (i don't know why it didn't work earlier). Now i can't boot a new os because the bootloader is locked and i don't remember mi account password (trying to log in by xiaomi mi tool v2)
Click to expand...
Click to collapse
oh btw, u can open up 9008 mode buy jumping test point, that way u can get into EDL
palloza02 said:
oh btw, u can open up 9008 mode buy jumping test point, that way u can get into EDL
Click to expand...
Click to collapse
I've tried to get into 9008 by diy edl cable and test points. I have all drivers. Still not working.