Database Develop

[Discussion] NULL_ROM Official Q/A - FAQ- General Discussion thread

This is place where you can come and ask questions regarding support as well as any other general discussion for the Null rom. Please keep the development thread to just that DEVELOPMENT. The developer of this rom is here to develop and not here to answer your questions because you can't take the time to figure out the answer yourself. This will be a community driven thread. Therefore, if you feel something needs to be added to the OP please mention me in a post and I'll take a look
If you need to download the rom free to stop by the dev thread to download. However, if I see you ask a question in here and then go to that thread to ask the same question I will be handing out infractions. Please consider this your only warning.
On a side note, I'll be transferring the OP of this thread to a person with this device in due time. However, for the moment this needed to be created. If you are willing to take the OP from me please feel free to send me a PM. The only requirement that I would have is that you keep it updated properly.
FAQ / IT DOESNT WORK ! WAH
INTERNET ACCESS
GO INTO "FULL SETTINGS -> BLUETOOTH -> SELECT YOUR PHONE SETTING ICON (ON THE RIGHT OF PHONE NAME) -> TICK INTERNET ACCESS".
ENSURE BLUETOOTH TETHERING IS ENABLED ON YOUR PHONE BEFORE HAND OBVIOUSLY.
*NOTE* ENSURE YOUR MOBILE DEVICE SUPPORTS TETHERING, US VARIANT PHONES HAVE RESTRICTIONS INPLACE. REFER TO THE US INTERNET TETHERING THREAD.
*NOTE 2* BLUETOOTH TETHERING DOES NOT AUTO RECONNECT, INSTALL THIS THIRDPARTY SOLUTION ON YOUR GEAR TO ENABLE AUTO RECONNECT.
PLAYSTORE / GOOGLE ACCOUNT MANAGER HAS STOPPED..
VERIFY YOU HAVE A BLUETOOTH INTERNET TETHERING CONNECTION ESTABLISHED BEFORE ATTEMPTING TO ADD A GOOGLE ACCOUNT.
MUST NOT BE USING THIRD PARTY TETHERING, EG. PDANET.
HOW DO I FULL WIPE?
BOOT INTO RECOVERY MODE AND SELECT THE "RECOVERY" OPTION. DO THIS AFTER FLASHING THE ROM
UNABLE TO WAKE GEAR WHILE IN PHONE CALL
THIS IS CAUSED BY THE HOME BUTTON REMAP MOD, THE HOME BUTTON MUST BE PRESSED IN ORDER TO WAKE THE GEAR UP IN THIS STATE.
ONLY WORK AROUND IS TO EITHER USE THE WRIST WAKEUP GESTURE OR DISABLE THE HOME BUTTON REMAP MOD.
*NOTE* BY DISABLING THE HOME BUTTON REMAP MOD, THIS WILL DISABLE THE ABILITY TO MANUALLY LOCK THE SCREEN WHILE USING A CUSTOM LAUNCHER.
DOUBLE TAP BRIGHTNESS/SOUND TOGGLE HAS DISAPPEARED
THIS IS CAUSED BY USING THE FULL SYSTEM UI, SIMPLY PUT IT REPLACES THE DOUBLE TAP WINDOW WITH THE NOTIFICATION SHADE. BY USING GRAVITYBOX YOU CAN ADD ADDITIONAL TOGGLES LIKE BRIGHTNESS & SOUND TILES TO THE FULL NOTIFICATION SHADE.
OTHERWISE SIMPLY REFLASH THE ROM WITH THE FULL SYSTEMUI OPTION UNTICKED.
SCREEN FLICKERING/GITTERING
THIS IS CAUSED BY THE INITIAL BOOTUP, REBUILDING THE CACHE AND INITIALIZING ALL THE APPS. GIVE YOUR GEAR A FEW MINUTES TO SETUP AND RESTART.
SCREEN UNLOCKS TO NOVALAUNCHER PAGE PREVIEW?
GO INTO "NOVA SETTINGS -> GESTURES -> HOME BUTTON -> NONE".
ENABLE DEVELOPER SETTINGS / USB DEBUGGING
GO INTO "SETTINGS -> GEAR INFO -> ABOUT GEAR", TAP SOFTWARE VERSION 10 TIMES.
ENABLE UNKNOWN SOURCE APK INSTALLATION
GO INTO "FULL SETTINGS -> SECURITY -> TICK UNKNOWN SOURCES".
ENABLE MTP
GO INTO "FULL SETTINGS -> STORAGE -> MENU BUTTON (TOP RIGHT OF SCREEN) -> USB COMPUTER CONNECTION -> MEDIA DEVICE (MTP)".
WATCH STYLER NOT WORKING
ENSURE ITS SELECTED AS THE DEFAULT WATCHFACE IN GEAR MANAGER.
IF CLOCK FACE DOES NOT UPDATE UPON CHANGING, RESTART GEAR.
DOUBLE CLICK HOME BUTTON DOESNT WORK ON TOUCHWIZ LAUNCHER !
*NOTE* DO NOT DO THE FOLLOWING IF YOU ARE USING NOVALAUNCHER, YOU WILL NOT BE ABLE TO MANUALLY LOCK YOUR GEAR.
*NOTE 2* YOU CAN SIMPLY REFLASH THE ROM WITHOUT WIPING AND DISABLE THE HOME BUTTON REMAP MOD.
NAVIGATE/PULL THE FOLLOWING FILE FROM YOUR GEAR: /SYSTEM/USR/KEYLAYOUT/GPIO-KEYS.XML
EDIT IN A TEXT EDITOR SO IT LOOKS LIKE THE BELOW:
Code:
key 115 VOLUME_UP WAKE
key 114 VOLUME_DOWN WAKE
key 116 POWER WAKE
[B]key 172 HOME WAKE[/B]
​

edit

Amazing. This thread is very much needed song as how the dev thread keeps getting cluttered with posts that wouldn't be there if some one would have read
sent from my Note 3 or Galaxy Gear

Yeah this thread is an awesome idea to leave the general discussion and support issues out of the other thread.

Whenever I select "recovery" it doesn't give me an option to install the rom?
I followed the steps for the root and the add the .zip to my SD card on the phone. When I select the option for recovery it just does a system restore on it. Any help?

You need to flash twrp first
sent from my Note 3 or Galaxy Gear

feature request
[what about to include support fpr AquaMail client?
I'm using it and I think it is the better at the moment
The developer could be interesting....

Just a quick (somewhat noob) enquiry about the Gear and what this ROM can do for it, as I'm thinking of picking up a Note3 + Gear from work (Vodafone), as the watch is free.
Firstly, I hate Touchwiz with a passion! I don't wish for anyone to read that in an angry way, but I'm really not fond of the colours, themeing, etc. of that particular UI. I much prefer vanilla Android and, as such, would look to root the Note3 and install CM or an equivalent on it.
Would I then lose any functionality of the Gear? Can the GearManager APK be installed on a non-TW ROM?
I'll need a bit of an idiot's guide for the whole thing, but it's nothing I can't research.

Pepski said:
Just a quick (somewhat noob) enquiry about the Gear and what this ROM can do for it, as I'm thinking of picking up a Note3 + Gear from work (Vodafone), as the watch is free.
Firstly, I hate Touchwiz with a passion! I don't wish for anyone to read that in an angry way, but I'm really not fond of the colours, themeing, etc. of that particular UI. I much prefer vanilla Android and, as such, would look to root the Note3 and install CM or an equivalent on it.
Would I then lose any functionality of the Gear? Can the GearManager APK be installed on a non-TW ROM?
I'll need a bit of an idiot's guide for the whole thing, but it's nothing I can't research.
Click to expand...
Click to collapse
No. Sadly not.
Or at least not with all the bells and whistles working.

I actually am testing CM11 on my note 3 as I type. I was wondering if someone could link me to the latest gear manager so I could test how it works.
Sent from my Note 3 w/ CM11

ktetreault14 said:
I actually am testing CM11 on my note 3 as I type. I was wondering if someone could link me to the latest gear manager so I could test how it works.
Sent from my Note 3 w/ CM11
Click to expand...
Click to collapse
Here's 2 versions. The latest and the previous one, a lot of people are having problems with the latest, and even Samsung supposedly admitted it was bugged and they were going to release a new one. The previous version seems to work fine for people, and there's no real functional updates on the latest one anyway, so you might prefer it.
Latest version - 1.5.121601
Previous version - 1.5.120903

I couldn't get cm11 to download the necessary apks for gear manager so I restored a tw backup and backed up the apks themselves. When I went to restore them the only ones that would not restore were the weather and svoice. It is paired now with gear manager running in the notifications. Still testing out what works and what doesn't
Sent from my Note 3 w/ CM11

Running 16, removed Ms. Pac-Man for running too slow on the Gear, everything's running smooth.
Sent from Spaceball One.

I have nexus 5 rooted and running null16, could anyone please point me out how to make gear manager to work?has anyone made notifications work? so far i can just make calls from it and syncs the time.I have read everywhere but nothing works so far and i can't seem to find a reliable sorce of information. If we could make something like an app and null to be modified to work with that so we lose gear manager dependency i belive that would be a game changer . Fomey i will donate something pretty soon as i allways apreciate work from people creative like yourself .
EDIT: 15 AUD for you Fomey, thank you for your work !

reboot after install of null_16
i have attempted several times now to install the null_16 on my galaxy gear. after each time i attempt to go into the recovery mode to actually install it, it reboots and resets the device. i have read numerous times to flash the null_03_TWRP2.7.tar.md5 file and i have done this with odin and received a pass at the top left of the odin program and then it reboots the galaxy gear. i then install the null_16 file on the root of the sd card directory with wondershare mobilego (left zipped as noted in several videos i have watched) after this i remove device from charging device and this is when i try to go to recovery modeto install. after getting to recovery and holding power button for approximately 3 seconds and release this is when it reboots and has reset itself. any help would greatly be appreciated and yes it is rooted with supersu. I am sure i am doing something wrong but not sure what.

ernie36564 said:
i have attempted several times now to install the null_16 on my galaxy gear. after each time i attempt to go into the recovery mode to actually install it, it reboots and resets the device. i have read numerous times to flash the null_03_TWRP2.7.tar.md5 file and i have done this with odin and received a pass at the top left of the odin program and then it reboots the galaxy gear. i then install the null_16 file on the root of the sd card directory with wondershare mobilego (left zipped as noted in several videos i have watched) after this i remove device from charging device and this is when i try to go to recovery modeto install. after getting to recovery and holding power button for approximately 3 seconds and release this is when it reboots and has reset itself. any help would greatly be appreciated and yes it is rooted with supersu. I am sure i am doing something wrong but not sure what.
Click to expand...
Click to collapse
Read.

ernie36564 said:
i have attempted several times now to install the null_16 on my galaxy gear. after each time i attempt to go into the recovery mode to actually install it, it reboots and resets the device. i have read numerous times to flash the null_03_TWRP2.7.tar.md5 file and i have done this with odin and received a pass at the top left of the odin program and then it reboots the galaxy gear. i then install the null_16 file on the root of the sd card directory with wondershare mobilego (left zipped as noted in several videos i have watched) after this i remove device from charging device and this is when i try to go to recovery modeto install. after getting to recovery and holding power button for approximately 3 seconds and release this is when it reboots and has reset itself. any help would greatly be appreciated and yes it is rooted with supersu. I am sure i am doing something wrong but not sure what.
Click to expand...
Click to collapse
Download mk7 for your country.... I don't care if you are already on it just do it! Flash with Odin then flash twrp recovery..... Use adb to boot to recovery....... Trust me it works!
Sent from my Note 3 SM-N900A rooted by Designgears

OMG i got it running!
thanks so much for all the work done with this rom... Everything seems to be running perfect...
At first i couldn't get it to flash properly... I was trying everything. Took hours to initially get the recovery going. It ended up being a driver issue and after a lot of reading and troubleshooting i was finally able to get it up and running.
One question that i have that i couldn't find the answer too... Is there any way to have the watch widget (either the stock clocks or watch styler) appear as a full screen widget without the launcher or the status bar at the top... yet keep the status bar and launcher on the other pages? I am assuming that i can't do it after reading countless of pages... Because i do like the full screen watch face.
Thanks again for all the hard work!
---------- Post added at 09:05 PM ---------- Previous post was at 09:00 PM ----------
eroracing said:
Download mk7 for your country.... I don't care if you are already on it just do it! Flash with Odin then flash twrp recovery..... Use adb to boot to recovery....... Trust me it works!
Sent from my Note 3 SM-N900A rooted by Designgears
Click to expand...
Click to collapse
I had to follow this step in order to get the recovery to stick. No matter what i did including flashing the stock recovery then flashing twrp i couldnt get it going until i did this:
almulder1092 said:
Installing Null_ TWRP: (Version as of this tutorial is Null_ 03 TWRP)
Thanks to fOmey for this Null_ TWRP
Installing Null_ TWRP:
Preparation:
Download Null_ TWRP - fOmey
READ THE NULL_ TWRP Original Post
Installation:
Put your Gear into Download Mode
Connect your Gear to you PC.
Open Odin
Click on the PDA Button
Locate the Null_ TWRP file and select it. (It should be a .md5 file, if it is zipped, then unzip it)
Press Start
Once it is completed it will reboot the gear.
Null Quote:
If you find the recovery is not sticking & your Gear wipes when attempting to access recovery after flashing, you must root your Gear prior to installing TWRP again & Run the following commands in ADB:
*NOTE* You will gave to accept a supersuser request popup when executing "SU" command
*NOTE 2* Probably a good idea to run this prior to first installation (To save time)
Code:
$ adb shell
$ su
# mount -o rw,remount /dev/block/mmcblk0p20 /system
# rm /system/recovery-from-boot.p
ADB stands for Android Debug Bridge
If needed "ADB" can be found here on xda - Thanks to shimp208​​
.[/CENTER]
Click to expand...
Click to collapse

gypsydigi said:
OMG i got it running!
thanks so much for all the work done with this rom... Everything seems to be running perfect...
At first i couldn't get it to flash properly... I was trying everything. Took hours to initially get the recovery going. It ended up being a driver issue and after a lot of reading and troubleshooting i was finally able to get it up and running.
One question that i have that i couldn't find the answer too... Is there any way to have the watch widget (either the stock clocks or watch styler) appear as a full screen widget without the launcher or the status bar at the top... yet keep the status bar and launcher on the other pages? I am assuming that i can't do it after reading countless of pages... Because i do like the full screen watch face.
Thanks again for all the hard work!
---------- Post added at 09:05 PM ---------- Previous post was at 09:00 PM ----------
I had to follow this step in order to get the recovery to stick. No matter what i did including flashing the stock recovery then flashing twrp i couldnt get it going until i did this:
Click to expand...
Click to collapse
You cannot do what you are asking.... But you can set clock widget. Use Nova settings to hide notification bar, dock and scroll indicators then use gesture and button settings to create gesture to accommodate just about anything! I have swype down to open notification bar..... Swipe up open notification app.... Double tap opens app drawer and 2 finger Swipe up opens my dialer! Just set widget long press and resize to full screen. You may have to adjust colums and rows in Nova settings to accommodate whatever widget you are using in order to center properly. Hope this helps!
Sent from my Note 3 SM-N900A rooted by Designgears

On the newest release (16) there is support for custom boot animation and includes the null boot animation. Is that a part of the aroma installer or is the custom null boot animation a part of the rom that you cannot remove? I'd rather stick with the stock if you don't mind.

Fix dec 2016/jan 2017: Snapchat on rooted android device running xposed.

POST IS UPDATED REGULARLY.
LINK 1 - Parallel Space: https://play.google.com/store/apps/details?id=com.lbe.parallel.intl&hl=en[/URL][/URL]
LINK 2 - Parallel Space 64-Bit Support: https://play.google.com/store/apps/details?id=com.lbe.parallel.intl.arm64&hl=en[/URL][/URL]
Salutations. (That means 'Hello').
NOTE: For those who are interested, I will include background information about how I came to the solution. All that other jazz too. First and foremost however; the fix!
SOLUTION:
Right at the top of the post, you will find two links. This being a new account and all (don't ask), until I create 10 posts I cannot include any outside links. So once I've done so, I will update the post.
STEP **: So at the top of the post, there are clearly two links. 64-Bit Android devices are becoming increasingly common. This architecture may pose a few problems. give the application framework. Should you own a 64-Bit device, I recommend installing this application too (LINK 2). This will theoretically prevent any obstacles.
Pre-requisite(s): Make sure you have the 'Snapchat' application installed. It is recommended to have installed the latest update from the Google Play Store.
STEP ONE: Download the application appended to LINK 1. This is called Parallel Space. You might recognize the name (its creators are the same who allow you to seamlessly virtualize Windows OS on Mac OS).
STEP TWO: Launch the application.
STEP THREE: You should be prompted with a grid-like interface. Here you will be greeted with a range of familiar icons. In the top right corner of each icon, you will notice a blue check-mark. Make sure that there is one next to the 'Snapchat' icon. This will ensure that the app is 'cloned'.
STEP FOUR: In the 'Parallel Space' app, tap on the 'Snapchat' icon. This will launch the application.
STEP FIVE: From here it is pretty self-explanatory. You are greeted by the standard 'Snapchat' interface. Tap on 'Log In'. Then proceed to do so.
STEP SIX: 'Snapchat' should be functioning as normal.
STEP SEVEN (BONUS): During testing, this worked on and off. --
Remain logged-in to the 'cloned' 'Snapchat' application within the 'Parallel Space' application.
Then proceed to launch the stock 'Snapchat' application.
Next attempt to 'Log-In'.
Should this operation be successful, you are then free to uninstall 'Parallel Space' and any related assets from your device.
HOWEVER, I personally do not recommend this. When logging out or updating the 'Snapchat' application, errors may be re-encountered.
Instead, I recommend that if possible, do use the stock application, but leave 'Parallel Space' installed. Using the stock app will improve efficiency and reduce the load on system resources. But keeping the 'Parallel Space' application on the device, well; you get the point.
Enjoy the fix! If it does not work, please let me know [Device Name and Model No.]. I've tested on various devices, succeeded every-time. Do keep in mind that this is a loop-hole, so may be patched in future or not work at all for some devices.
Background (Because I know someone will ask): The idea came to mind while using a LG G5 as a daily driver. I had tested every custom ROM available for the device. The problem was that with custom ROM's, there was always an issue, Malfunctioning sensors, camera's not working persistently, etc , etc.
The G5's stock ROM left me wanting more. The overbearing interface made it a living hell. Plus, the device just being rooted (NO XPOSED) meant that 'Snapchat' did not work. I looked for fixes for a time, but could not find any.
Development of ROM's for the device is on-going, and I am an active member. But I just couldn't handle not being able to use the camera (one of the device's best features) and no accelerator, screen-rotation, etc. So I went back to stock again. Do keep in mind that I was alternating/dual-booting between custom and stock ROM's just because of the camera; mainly.
This most recent time. instead of flashing stock MM, I flashed stock N for the G5. For 850, it has been officially released in some countries, and a manual flash via TWRP was a peice of cake.
This update is a lot better. I am running Nova Launcher again. So it makes it look a little better. Themes have also been improved. I am using an in-built dark one which makes the device look a lot better aesthetically. Additionally, I'm rocking a white carbon-fibre skin on the exterior; improving grip and overall security. The only issue was again, no 'Snapchat'.
After a few days, I had the idea to attempt this. I tested my theory and it worked! That's it.
Please do keep in mind that I will update this post as often as possible.
P.S This was tested just after updating to the latest version of 'Snapchat' which was a significant update. It included Shazam, Groups, etc. So you know, pretty cool that it worked.

Did not work on Google Nexus 5 running Android 7.1.1. Still gives error message saying that I can't connect to the server.

Same here, not working on freshly reinstalled and rooted 7.1.1 Nexus 5x. No Xposed, no nothing. I get the infuriating "temporarily failed" message in both cloned and regular modes.

It didn't worked. S7 edge exynos (6.0.1)

Holyphe said:
It didn't worked. S7 edge exynos (6.0.1)
Click to expand...
Click to collapse
I'm pretty sure if you get Xposed framework, there's a module that allows you to hide root from apps. Problem is that there is no Xposed framework for Android 7 yet. Hope this helps.

hot_potato said:
I'm pretty sure if you get Xposed framework, there's a module that allows you to hide root from apps. Problem is that there is no Xposed framework for Android 7 yet. Hope this helps.
Click to expand...
Click to collapse
Whats the name of it?

Holyphe said:
Whats the name of it?
Click to expand...
Click to collapse
I personally tried the module on cm13 but it doesnt work for me. I think that somehow snapchat knows when you use xposed too.
The thing is that on aosp roms with root already build in sometimes snapchat do not catch it but if you have xposed, no way you can get in. For that freaky snapchat app here is what i did: install any rom, if if had root build in i then install su uninstaller zip with twrp then log in into snapchat and after that, rooting with super su zip again. The catch is that once you log out of the app and attempt to log in again, you cant get in and you have to repeat the proccess. It's annoying as hell!!! They need to disable the security check, if people want to cheat che system somehow they will, so whats the point. Also there are much more tweaks for jailbroken iphones and they have no problem with it .
Sorry for the rant here buqt im super frustrated.

AndroidFL said:
I personally tried the module on cm13 but it doesnt work for me. I think that somehow snapchat knows when you use xposed too.
The thing is that on aosp roms with root already build in sometimes snapchat do not catch it but if you have xposed, no way you can get in. For that freaky snapchat app here is what i did: install any rom, if if had root build in i then install su uninstaller zip with twrp then log in into snapchat and after that, rooting with super su zip again. The catch is that once you log out of the app and attempt to log in again, you cant get in and you have to repeat the proccess. It's annoying as hell!!! They need to disable the security check, if people want to cheat che system somehow they will, so whats the point. Also there are much more tweaks for jailbroken iphones and they have no problem with it .
Sorry for the rant here buqt im super frustrated.
Click to expand...
Click to collapse
That's the only solution I've seen working so far. unroot and reroot. Root cloak doesn't work, parallel doesn't work. I should've logged in before rooting and I hate to do it again.

Any work arounds yet? I've seen ppl do it using titanium backup but I'm not sure if that works. Can anybody help?

Samsung s5 G900v Not working
I have been searching and searching and still haven't found a way to sign into snapcat. It took me about 6 months to be able to find out how to root my phone.

Dukeboyty said:
I have been searching and searching and still haven't found a way to sign into snapcat. It took me about 6 months to be able to find out how to root my phone.
Click to expand...
Click to collapse
Well todays your lucky day.
Step one turn off xposed.
Step two reboot
Step three sign into snapchat
Step four turn xposed back on
Step five reboot
You should be able to snap now.

Okay. I will try this on monday and will let youknow how it goes. Right now I decided to unroot to use snapchat, so I didn't loose my streaks. Thanks in advane will let you know how it goes.

immorality said:
Well todays your lucky day.
Step one turn off xposed.
Step two reboot
Step three sign into snapchat
Step four turn xposed back on
Step five reboot
You should be able to snap now.
Click to expand...
Click to collapse
Now that i think of it, when i uninstalled xposed it didn't work still. but after i "fully unrooted" through Super su and tried to sign in it worked. so it has to do with root or maybe both but the xposed didnt work for me. Thanks even though it didn't/wouldn't have worked for me!

Dukeboyty said:
Now that i think of it, when i uninstalled xposed it didn't work still. but after i "fully unrooted" through Super su and tried to sign in it worked. so it has to do with root or maybe both but the xposed didnt work for me. Thanks even though it didn't/wouldn't have worked for me!
Click to expand...
Click to collapse
Snapchat detects xposed framework.
Though at a time they did do root they since moved to blocking xposed due to the security concerns with money and also privacy of the user.
Though with certain phones and ect that could be the case I am using a s5 and have no issues.

just install magisk and systemless xposed and turn on magisk hide in magisk manager now snapchat won't detect root
then when u wanna log in just turn off xposed in xposed installer and reboot "it won't take time booting optimizing app when reactivated now" so reboot is easy
and u can have multiple accounts by backing up snapchat with titanium backup and don't ever log out just wibe its data and when u want to relog just restore the backup
and if u want to have multiple accounts access just patch the titanium backup with luckypatcher and have multiple backups (accounts)

ahmedsasker said:
just install magisk and systemless xposed and turn on magisk hide in magisk manager now snapchat won't detect root
then when u wanna log in just turn off xposed in xposed installer and reboot "it won't take time booting optimizing app when reactivated now" so reboot is easy
and u can have multiple accounts by backing up snapchat with titanium backup and don't ever log out just wibe its data and when u want to relog just restore the backup
and if u want to have multiple accounts access just patch the titanium backup with luckypatcher and have multiple backups (accounts)
Click to expand...
Click to collapse
Can u make a instructions how to do it step by step? How can i turn off xposed in xposed installer? It also works when SuperSu is installed or i have to unistall it first?

Fnn.09 said:
Can u make a instructions how to do it step by step? How can i turn off xposed in xposed installer? It also works when SuperSu is installed or i have to unistall it first?
Click to expand...
Click to collapse
make a nandroid backup if u want
1- full unroot by opening supersu and going to settings and press Full unroot and wait till it finishes and restart
2- download xposed uninstaller if u have xposed framework installed and flash it
3- install magisk manager from playstore
4- download and flash last magisk which is (12v) now from : https://forum.xda-developers.com/apps/magisk/official-magisk-v7-universal-systemless-t3473445
5- flash magisk v12.0 which you downloaded now your phone will have systemless root
6- go into magisk manager app and go to settings and toggle "Magisk Hide" (ON) and restart now your root is hidden
7- remove your current xposed app and install this one : https://forum.xda-developers.com/xposed/material-design-xposed-installer-t3137758
8- flash systemless xposed : https://forum.xda-developers.com/xposed/unofficial-systemless-xposed-t3388268
9- reboot and go to the xposed installer app and toggle the xposed off or on as you want when u restart it won't take time optimizing apps like before so fast now
your root is hidden now but xposed is not but you can disable it and enable it easily

Instead of using Parallel Space (which I believe to be insecure) use Island to clone your apps. It's a little more advanced to setup, but it's a lot more secure. It works for rooted and non-rooted devices. On the 1st page of the thread, it explains how Parallel Space and others repack the apk file locally, which is dangerous. https://forum.xda-developers.com/android/apps-games/closed-beta-test-incoming-companion-app-t3366295
Island never repack apk file locally, which is inherently insecure for users, since all your app data (including password input) are technically in the hand of MoboClean. (The same applies to other similar tools, e.g. LBE Parallel Space)
Instead, Island takes advantage of the underlying mechanism used by "Android for Work". This ensures that all your apps run natively in Android system and their data are securely stored in internal location of Android which is never accessible by Island. It has the same level of security as "Android for Work".
Click to expand...
Click to collapse
Be sure to read the disclaimer!!! The app is still only available in closed beta at the time of writing this, and could possibly cause you're device to bootloop or even possibly brick it, but root, xposed, or other modifications {in my opinion) has a higher chance of bootloops or bricking your device.
You follow the same steps in island to clone snapchat as you would in Parallel Space to login to snapchat. It might be possible to use the play store inside island to download snapchat inside island and login that way. I can't remember exactly how it works. I believe that island is a good way to test apps in a "sandbox environment" to keep the data excluded, safe and secure from the regular apps that you have installed outside of island.
I use Magisk now which bypasses SafetyNet which is what snapchat uses to "block access" to modified/rooted devices.
Probably the easiest method is to download Casper which is an alternative snapchat client that allows you to save snaps, and many other features that the official snapchat client can't do. Find Casper at www.casper.io
FYI Netflix has started to change how they do things as well by hiding the app's play store page from devices that have been modified or rooted, but it's still possible to simply sideload Netflix for now.

[GUIDE][GLOBAL]Flyme 7 update,Disable system apps,Enable night mode,Weather fix

First of all i highly recommend you update your phone to latest version of Flyme as of day i write this guide newest stable version is 7.0.0.0G. It brings various bug fixes as well as security update and new functions. It fixed the weather problem too when it would not appear on secondary screen. This is my experience based on the standard model with Helio P25 chip.
JUST IN CASE BACKUP ALL OF YOUR DATA FIRST
Grab it at http://www.flymeos.com/firmwarelist?modelId=88&type=1
Installation is pretty straightforward:
-switch off your phone
-now press volume up button and power button at same time, then release power button when meizu logo appears
-phone now will enter update mode, connect it to pc and it should show up as removable drive named recovery, copy the update.zip over it
-once copied tap the start button to begin. the process itself and first boot will take a while
-when done and phone boots up just log in to your accounts and set up everything as normal or whatever
ta-dah ! you should be running latest software now.
Next problem i've encountered was big number of unwanted apps and you will need working ADB for that. I've always used custom roms which did not contain bloatware. Now im giving you one of the way of disabling them (not permanent removal).
For this to be done you need to activate developer mode and usb debugging, simply go to settings->about phone->and now tap on your build number several times
After you activate it it will be available in accessibility options under developer settings. just check the usb debugging and you're good to go
DISCLAIMER: dont ask me about adb drivers for your phone, since i had issues installing them under win 10 x64 build 1803 i thought "aw f*ck it" and just did it on linux where everything worked out of the box.
The application you will need is called Ice Box (you will find it here https://play.google.com/store/apps/details?id=com.catchingnow.icebox&hl=en_US) and install it.
After you install the app its necessary that you remove ALL of your accounts including your Google account. We will need to grant the app device owner permission. Also if multi-user or guest mode has been set on your device, it need to be closed or deleted.
When you have that done just type in your command line , terminal or whatever "adb shell dpm set-device-owner com.catchingnow.icebox/.receiver.DPMReceiver "
Now reboot and add your accounts back, and disable/freeze uwanted apps.
Last - the night mode. As its no longer availble in Flyme 7 if you want to use it you need to manually bring it back by installing Flyme Lab and enabling it trough quickshortcutmanager. Install both apps, then open quickshortcutmanager and search for Flyme Lab. expand it and choose the activity named com.meizu.flymelab/com.meizu.flymelab.component.nightmode.NightModeSettingsActivity .Create shortcut and open it. You should be able to enter the night mode.

Nice guides, thanks.
It's also nice that Flyme 7 still supports rooting, therefore I'm using Titanium Backup to freeze unwanted apps. I bought it when I was using another phone so, for me, it's still worth it. Altough, for uninstalling system apps I'm using separate ADB commands for each app.

cris2d2 said:
Nice guides, thanks.
It's also nice that Flyme 7 still supports rooting, therefore I'm using Titanium Backup to freeze unwanted apps. I bought it when I was using another phone so, for me, it's still worth it. Altough, for uninstalling system apps I'm using separate ADB commands for each app.
Click to expand...
Click to collapse
Its first time for me writing a guide so good word is always appreciated. What im trying to show here is the no root way of getting rid of apps for ppl like me who dont want to root their phone. As i bought it literally two days ago and i dont want to mess with it too much and loose warranty or/and OTA updates.
I also been considering posting a root guide once i tried it myself to confirm it working.

non.verbal said:
Its first time for me writing a guide so good word is always appreciated. What im trying to show here is the no root way of getting rid of apps for ppl like me who dont want to root their phone. As i bought it literally two days ago and i dont want to mess with it too much and loose warranty or/and OTA updates.
I also been considering posting a root guide once i tried it myself to confirm it working.
Click to expand...
Click to collapse
Well, before I discovered a rooting method for Flyme 7, I used to uninstall apps by using ADB commands. So, yes, it is possible to remove unwanted system apps without root. But now, after rooting Flyme 7, I'm only using Titanium Backup to freeze unwanted system apps, not removing them.
As far as I know, rooting Meizu phones by the official method (from Settings) does not lead to losing warranty. Only OTA updates are lost, but this is not important, at least to me, because I can always check Flyme website for new updates and, if I want to update, I just download the file and flash it through standard Flyme recovery. There is no need, for me, to maintain OTA capability. Anyhow, Flyme updates are slow to non-existent, so we can't really complain about losing an update.

Thank you all. I'm happy with this phone at all, but software has few shortcomings and design flaws, in my opinion. Especially related to the integration with "flyme login" and Touchpal. This last one is very annoying because although I try to stop it, at each software update it comes back, more annoying than ever. So, I have some questions: which is the adb command to stop and freeze bloatware without rooting? Which is the official way to root the phone? Once rooted, is it possible to revert to the unrooted state? Some apps, actually, do not work on rooted phones. Thanks

pask876 said:
Thank you all. I'm happy with this phone at all, but software has few shortcomings and design flaws, in my opinion. Especially related to the integration with "flyme login" and Touchpal. This last one is very annoying because although I try to stop it, at each software update it comes back, more annoying than ever. So, I have some questions: which is the adb command to stop and freeze bloatware without rooting? Which is the official way to root the phone? Once rooted, is it possible to revert to the unrooted state? Some apps, actually, do not work on rooted phones. Thanks
Click to expand...
Click to collapse
I can't freeze (or disable) apps with ADB commands, only uninstall.
You need [email protected], App Inspector or similar (to find exact name of package for an app) and these commands:
adb devices
adb shell
pm uninstall -k --user 0 name_of_package
Example, for gmail:
pm uninstall -k --user 0 com.google.android.gm
Regarding rooting, as far as I know, the only method that works on Pro 7 / Pro 7 Plus is also supported by Meizu (but it breaks OTA updates).
The method is described in this video (in russian) but it's quite easy.
If you want to remove root (or if root breaks functionality) you have to reflash the same ROM from Recovery (without wipe).

Any air update coming soon? Or manually installation single option?

[ROM][TMOBILE][S7_SM-G930T][Oreo 8.0 Rooted][WifiCalling]

Updated version of this ROM: [ROM][TMOBILE][S7_SM-G930T][Oreo 8.0 Rooted][WifiCalling]G930TUVU4CRI2
ROM last updated: 10/30/2018
Introduction:
HUGE thanks to the guys that got this going like root & figuring out hybrid stocks! This ROM is a complete rewrite of my ROM [ROM][TMOBILE][S7_SM-G930T][Oreo Rooted] That ROM doesnt have WifiCalling & I couldn't get it to work for the life of me, so I rewrote it. I started with stock, and slowly stepped back making changes, reinstalling each time, confirming it still worked. About 200 installs later & 1000s of changes, this is the result. Yes, it took a LONG time. Hope you enjoy it! Don't forget to say Thanks so I know it is actually helpful to others, and continue doing this!
Description:
Stock Tmobile Oreo 8.0 modified (G930TUVU4CRF1)
EXTREMELY debloated! Nearly bare minimum, while still retaining hardware functionality. Eg, Samsung Gallery & Camera exist so we get 4k recording, and there aren't errors when we pull up the Gallery to edit, etc. Yes, this means NO Samsung or Android Pay. There could be more apps to debloat but Im out of time for now! (Please provide suggestions if interested)
Everything possible I replace Samsung with Google
Solid ROM. It was actually kind of slow for me, but I'm curious how this works for others.
Xposed is part of the guide, which will give you infinite customization & tweak-ability
If you hate Samsung SW and just want a solid working ROM with very few install options to get you up and running this is for you.
This will delete all of your data on the phone! (Not external SD card) This is the only way so don't ask. Backup your data!
Features:
Tmobile Wifi Calling works, along with Visual Voicemail & Mobile Hotspot
Many Aroma Installer app options
(Optional) KevinsFavorites option in Aroma. I'm not sure I'd recommend it due to my tastes. If you're looking for some good common apps tho, it includes: Amazon, AmazonMusic, AquaMail, Gmail, GoogleDrive, GoogleKeep, GooglePhoto, Hangouts, IFTTT, Pandora, RootBrowserClassic, TitaniumBackup, Uber, & Wink (If you install these and want to remove them later, use TitaniumBackup (or similiar) to uninstall
Root Features: See Downloads->Recommended Root Zip & say Thanks!
Debloated
De-Knoxed
Decrypted /data/ partition
OTAs disabled
Speed & Build Prop Tweaks
Dual speaker
Ruthless Launcher
Apps
AdAway
AOD Clock Face Themes
CPUSpy
DisableService
Kernel Adiutor
Samsung Video Editor and Trimmer
Xposed
Many more...
Download Links:
Base.7z & Oreo_Kevin71246Modded_v3.#.#.zip
Installation:
This will delete all of your data! If you continue, you acknowledge that the Author is NOT responsible for anything that happens to your phone!
Summary (for Pros)
Flash Oreo stock
Root
Flashfire
Oreo_Kevin71246Modded_v3.1.##, Auto-mount, Mount /system read/write Option
Go through Aroma setup. When finished, it should boot to Recovery (if not do this). Do a "Wipe data/factory reset"->Reboot
Detailed Steps
Install Stock Oreo:
Download mode & Setup
Make sure you have latest device drivers setup on your PC
Enable USB Debugging on phone in Developer Settings
Boot phone into Download Mode:
Turn off your device
Press and hold Volume Down + Home + Power button
When you see the warning screen, release buttons & press Vol UP. Phone should say "Downloading..."
Download and unzip Base.7z to PC (This contains stock Oreo, ODIN, & root)
ODIN
Open ODIN on PC (\Base\Odin_313.exe)
Connect USB from PC to phone. ID:COM in Odin should turn Blue with a COM port
Select AP, BL, CP and CSC files from the \Oreo_Stock\Base\ folder for corresponding files
Select HERO2QLTE_USA_VZW.pit
Select Start
Finished: Phone will reboot & show Carrier screen for 3-5mins. Wait until Setup screen & go through quickly (bare minimum) since you'll wipe it again. Once in Android, go to Settings->Display->Screen resolution->WQHD->Apply
Root Instructions: (+Flashfire, SuperSU)
Reboot phone into Download mode
Odin
AP: Select \Base\Root\AP_SM_G930_OREO_ENG_BOOT.tar
Start-> Wait for phone to boot to Android OS
Root
Double-click \Base\Root\cmd-here.exe & Type: root.bat [enter]
Option: 1 (Install Root No tweaks) (Or pick whatever you want)
*Note: With this system root, do not update su binary. Disable notifications for SuperSU app. Don't flash any superuser zips in recovery that are not made by jrkruse
Install Custom Hybrid ROM & Xposed
Download & copy Oreo_Kevin71246Modded_v##.zip to phone
Flashfire
Open Flashfire on phone
Red + symbol->Flash Zip or OTA->Oreo_Kevin71246Modded_v#, Auto-mount, Mount /system read/write Option->Check mark
Click Lighting bolt at bottom-> OK
Phone will reboot to Aroma. Go through setup. (See above for what's in KevinsFavorites)
When finished, allow Aroma to exit.
It should reboot into Recovery (If not, do this: immediately hold Vol-Up btn+Home btn until you see recovery on screen. If you missed it, try again: hold Vol-Down+Pwr btn ~10sec until phone restarts & immediately hold Vol-Up btn+Home btn until you see recovery on screen.)
In recovery: Factory Reset->Yes->Restart phone
*Wait 5-10min on loading screens
Go thru Android setup. Ignore "Xposed Installer has stopped" error
Followup-Steps:
Set Dialer: Phone Settings->Apps->Menu->Default Apps->Calling App->Select Phone
Recommendations:
Xposed
Setup Xposed: Xposed Installer app:Install framework option & restart phone
Xposed Installer app: Settings button (3 lines)->Download->Search "GravityBox [O]"->Click it->Versions tab->Download->Install->Back arrow (upper left)->Settings->Modules->Check box next to GravityBox [O]->Restart phone
GravityBox [O] Tweaks: (Open GravityBox app)
Battery indicator: Statusbar tweaks->Battery settings->Turn on Master switch->Battery indicatory style: None->Battery percent text...->Back
Clock: Statusbar tweaks->Clock settings->Turn on Master switch->Center clock...
Firefds Kit [O] Tweaks: (Install same way as Gravity box)
This is a supplement to Gravitybox. Things of note: Advanced power menu, call recording, & disable bluetooth toggle popup, etc
Known Issues:
Visual Voicemail may fail to register, but restart phone and give it a few hours. It works eventually.
RCS (Rich Communication Services/AdvancedMessages/Chat) texts don't show up in Android Messages & Textra, etc apps (This is an issue on stock as well!!)
Fix: (Use Samsung Messages)
How to Install Samsung Messages via ADB (Easiest way though is just reinstall!):
Download Messaging_SEP81.zip, unzip, & manually copy apk to phone via usb/Windows My Computer
adb shell (Get into shell to run beow commands)
su (Run as root)
mount -o rw,remount /system (Mount system read/write since default it read-only)
chmod 755 /system/priv-app/Messaging_SEP81 (Set permissions on folder)
chmod -R 644 /system/priv-app/Messaging_SEP81 (Set permissions on apk file)
ls -l /system/priv-app/Messaging_SEP81 (Check permissions - Should be: -rw-r--r-- 1 root root - not sure what 1 & 2 is)
ls -l /system/priv-app | grep "Messaging" (Check permissions - Should be: drwxr-xr-x 2 root root)
reboot (Reboot device)
Changelog:
Version 3.1.32: First stable build
Ver 3.1.36:
-Disabled encryption on /data/ partition to resolve "Bluetooth paired devices deleted after reboot" issue & so mods play nicer with ROM
-Fixed "Device not supported" error on Google Phone app
Ver 3.1.37:
-Added most of the apps I replaced or added as options in Aroma Installer now
Credits:
- @jrkruse & @klabit87 for Root
- @partcyborg for helping jrkruse
- @jrkruse for his similar ROMs as guides & help
- @Lanc-City for assistance in ROM modding
- @gustco for eng boot.img
- @Raymonf for modified odin
- @amarullz for Aroma Installer
- @Chainfire for FlashFire & SuperSU
- @rovo89 for Xposed
- @JaeKar99 for the cool & colorful boot animation
- @mrRobinson for AdAway ADAway.org
- Brandon Valosek for CPUSpy
- WangQi for DisableService
- Willi Ye for Kernel Adiutor
- @shubby for Ruthless Launcher
- @Craz Basics for Dual Speaker Mod
...
- Please PM me if you were forgotten!

Some screenies:

Saved2

Saved3

Well nice job!

jrkruse said:
Well nice job!
Click to expand...
Click to collapse
...but your'e the best! (You & I both know I couldnt have done it without all your other work!)
Once I FINALLY got WifiCalling to work, I thought... Imagine ALL the S7 XDA members out there with crappy Tmobile signal across Rural America that could TOTALLY use Wifi Calling!!! Haha, but seriously!! & that thought was the birth of this thread

kevin71246 said:
...but your'e the best! (You & I both know I couldnt have done it without all your other work!)
Once I FINALLY got WifiCalling to work, I thought... Imagine ALL the S7 XDA members out there with crappy Tmobile signal across Rural America that could TOTALLY use Wifi Calling!!! Haha, but seriously!! & that thought was the birth of this thread
Click to expand...
Click to collapse
Is this Ufirm firmware?

jrkruse said:
Is this Ufirm firmware?
Click to expand...
Click to collapse
I have so many FW packages on my PC at this point, from so many places that I used while trying to get this to work, but I think it might be a package from one of your threads(?) Since I'm not exactly sure what you're asking regarding "Ufirm FW", I'll elaborate hoping that answers your question. (Tho I'm thinking you mean the U variation/unlocked. So based on these stock files below I guess the answer is no.) If you're question is really, "is it possible to get tmobile wifi calling to work on a U model #", then I'd have to really think about that. But at this point I don't have an answer. I can tell you a million dependencies about it tho! (I seriously have hundreds of revisions I made while testing, & notes. The symbolic & meta links in Aroma initially broke it, as I found out after a week or so of testing - wish I knew a bit more about them, and why they're all there, then I'd know what was wrong about them...)
High-level process:
1)Flash Base/Stock/Oreo Rom:
- AP_G930TUVU4CRF1.tar
- BL_G930TUVU4CRF1.tar
- CP_G930TUVU4CRF1.tar
- CSC_TMB_G930TTMB4CRF1.tar
- HEROQLTE_USA_VZW.pit
2)Root with your method
3)Flash Xposed framework & my ROM (it's a "start with stock then remove what we don't want" type of Aroma/Edify script)

jrkruse said:
Is this Ufirm firmware?
Click to expand...
Click to collapse
BTW, any idea how to prevent the "verification failed" error I mention in the OP steps, after flashing Xposed framework? I tried flashing dm-noverity but no luck. At least my guide covers it at this point tho... Thanks again

kevin71246 said:
BTW, any idea how to prevent the "verification failed" error I mention in the OP steps, after flashing Xposed framework? I tried flashing dm-noverity but no luck. At least my guide covers it at this point tho... Thanks again
Click to expand...
Click to collapse
If you choose the keep safestrap option during root the it will flash the system/vendor/etc/ fstab.qcom that totally removes data encryption but when that fstab.qcom is flashed it also requires a data wipe for phone to boot then when you install xposed you won’t see that error but either way you end up wiping data so your choice
Sent using some kind of device I modified

It works perfectly!!
I have not had any problems so far, here I leave you for the link to download and try those who are interested in VIPER4ANDROID: https://drive.google.com/file/d/1572ORe6TOrsRBuxWWBChH-WMnxkvcUjH/view?usp=drivesdk
You just have to flash it with Flashfire, but if you do not pull them, let me know Thank you very much !!! Kevin for the effort!
---------- Post added at 10:17 PM ---------- Previous post was at 10:15 PM ----------
I have not had any problems so far, here I leave you for the link to download and try those who are interested in VIPER4ANDROID: https://drive.google.com/file/d/1572ORe6TOrsRBuxWWBChH-WMnxkvcUjH/view?usp=drivesdk
You just have to flash it with Flashfire, but if you do not pull them, let me know Thank you very much !!! Kevin for the effort!

First, I want to thank you so much kevin71246. I tried your previous version as I was sick and tired of how sluggish my phone felt after the last two T-Mobile OTA updates. So far the experience on the phone has been great but I wanted to post about an issue I had with that version to see if anyone else has come across it or can figure out what is going on. The reason I am making this a reply in this thread instead of your other is because I will be flashing this update shortly but I want to get the ball rolling on the issue first.
I went through the whole process, installing the minimum with Google Apps, though I did restore everything previously installed once I log in with my Goggle Account. I am unsure if this contributed to the problem but I will not be restoring apps on the next try. It seems no matter what process I attempt to connect my Ticwatch E to my S7 the Wear OS app will not recognize it which causes the watch to get stuck in the setup phase, making it useless. This was after multiple and different connection attempts, resets, reboots and factory (watch only) restores. The watch will show up under bluetooth and create the initial connection but it will not stay connected. Anyone have any idea? Is this ROM missing something?
Edit: Mid way through the install, I wanted to note that I checked for the issue after doing the "Install Stock Oreo" but before Root and everything worked as it should. Wear OS sees the watch instantly and Bluetooth connects fine.
Edit: So I am a day into using the ROM and I am still having issues. While it will connect and work perfectly fine now, when ever I do a reboot of the phone the watch no longer connects. I will just get constant Bluetooth Connection Requests, every single time the watch tries to get data, and it never actually connects. To fix this I need to do a complete reset of the watch and do the whole setup process again. As you can imagine this is no good, expecting to wipe my watch every time my phone reboots makes it still almost useless.

charredchar said:
First, I want to thank you so much kevin71246. I tried your previous version as I was sick and tired of how sluggish my phone felt after the last two T-Mobile OTA updates. So far the experience on the phone has been great but I wanted to post about an issue I had with that version to see if anyone else has come across it or can figure out what is going on. The reason I am making this a reply in this thread instead of your other is because I will be flashing this update shortly but I want to get the ball rolling on the issue first.
I went through the whole process, installing the minimum with Google Apps, though I did restore everything previously installed once I log in with my Goggle Account. I am unsure if this contributed to the problem but I will not be restoring apps on the next try. It seems no matter what process I attempt to connect my Ticwatch E to my S7 the Wear OS app will not recognize it which causes the watch to get stuck in the setup phase, making it useless. This was after multiple and different connection attempts, resets, reboots and factory (watch only) restores. The watch will show up under bluetooth and create the initial connection but it will not stay connected. Anyone have any idea? Is this ROM missing something?
Edit: Mid way through the install, I wanted to note that I checked for the issue after doing the "Install Stock Oreo" but before Root and everything worked as it should. Wear OS sees the watch instantly and Bluetooth connects fine.
Edit: So I am a day into using the ROM and I am still having issues. While it will connect and work perfectly fine now, when ever I do a reboot of the phone the watch no longer connects. I will just get constant Bluetooth Connection Requests, every single time the watch tries to get data, and it never actually connects. To fix this I need to do a complete reset of the watch and do the whole setup process again. As you can imagine this is no good, expecting to wipe my watch every time my phone reboots makes it still almost useless.
Click to expand...
Click to collapse
I believe I know what the issue is, I'm testing a fix (for THIS ROM) as we speak. Stay tuned. Maybe tomorrow if I have time and it works I'll update the OP. BTW, this ROM and my other ROM are TOTALLY different. Thanks for the feedback!

FranMLG said:
I have not had any problems so far, here I leave you for the link to download and try those who are interested in VIPER4ANDROID: https://drive.google.com/file/d/1572ORe6TOrsRBuxWWBChH-WMnxkvcUjH/view?usp=drivesdk
You just have to flash it with Flashfire, but if you do not pull them, let me know Thank you very much !!! Kevin for the effort!
Click to expand...
Click to collapse
What do you mean by this? "but if you do not pull them, let me know"
And tell me more about Viper4Android, and if it works solid for you on this ROM...then I'll consider adding it. Thanks!

New version, see change log in OP for details.

Yeah i.a give this a shot in a little. Do I need to root phone or can I just flash through Odin. Sorry not used to this locked bootloader crap..... s8crj1 are the last 6 digits of the software I'm on. I did receive the latest update will this effect me installing this. Sorry as I said not used to this locked bootloader crap.

jrkruse said:
If you choose the keep safestrap option during root the it will flash the system/vendor/etc/ fstab.qcom that totally removes data encryption but when that fstab.qcom is flashed it also requires a data wipe for phone to boot then when you install xposed you won’t see that error but either way you end up wiping data so your choice
Sent using some kind of device I modified
Click to expand...
Click to collapse
Hi, why you have to flash this - HEROQLTE_USA_VZW.pit on 930t, is it ROM specified? if I do and don't then what are pro and cons?
---------- Post added at 01:36 PM ---------- Previous post was at 01:26 PM ----------
josh2020glacier said:
Yeah i.a give this a shot in a little. Do I need to root phone or can I just flash through Odin. Sorry not used to this locked bootloader crap..... s8crj1 are the last 6 digits of the software I'm on. I did receive the latest update will this effect me installing this. Sorry as I said not used to this locked bootloader crap.
Click to expand...
Click to collapse
since bootloader is locked you can't use TWRP so you have to use Flashfire to install this ROM, as you know flashfire required root so you have to setup the base per OP and then root the base then install the ROM and then root it again, read the first page I don't think you will get a instructions more detailed then his

Okay so I just realised I was posting comments on the old thread, my bad. Coming back to the question, can the boot animation be changed? I've messed with the qmg files in an attempt to replace the weird, nauseating rainbow animation but even after overwriting the latter, it persists. Looking forward to a reply kek

Alkan3 said:
Okay so I just realised I was posting comments on the old thread, my bad. Coming back to the question, can the boot animation be changed? I've messed with the qmg files in an attempt to replace the weird, nauseating rainbow animation but even after overwriting the latter, it persists. Looking forward to a reply kek
Click to expand...
Click to collapse
Nauseating rainbow? LOL. Sorry. This is much more of a general question though, that wouldn't exactly pertain to this ROM specifically. And given I don't have an answer, I'd try searching BootAnimation How-Tos to get this customized. The ONLY thing I did regarding this was replaced the existing files with the rainbow ones. That's it. Apologies in advance.

Just discovered an issue: RCS (Rich Communication Services / Chat) texts don't show up in Android Messages app. See "Known Issues" in OP for a solution. BTW I posted a new ROM version a few days back that allows many choices in Aroma Installer. Make sure to pick Samsung Messages (instead of Google), so you get RCS chat text messages!

General System root + Passed Safety Net Pixel 5a

Hey everyone,
after some trial and error, I was able to pass Safety Net.
I just want to mention what I did in the process to get there. May have been a combination of things or just one...
1. I followed this guide, but make sure you notice that It's for the Pixel 5 not 5a. But the process is similar. This process didn't fix the issue. However, it's also a good how-to on how to root. I did also modify the props to the 3a.
How to Root the Pixel 5 & Still Pass SafetyNet — Full Guide for Beginners & Intermediate Users
The Pixel 5 is a great value proposition in this era of $1,500 phones. With its reasonable price tag, fully open-sourced software, and unlockable bootloader, it's also an ideal phone for rooting.
android.gadgethacks.com
2. When that didn't work, I followed this video, and hid all my banking apps besides the Google Play Services:
3. When that didn't work, I installed these both using Magisk from this post:
Magisk General Support / Discussion
This is the place for general support and discussion regarding "Public Releases", which includes both stable and beta releases. All information, including troubleshoot guides and notes, are in the Announcement Thread
forum.xda-developers.com
4. Cleared my data and cache with Google Play and GPay + any other banking apps.
That worked for me!
EDIT: IF GOOGLE MAPS reports the wrong location, its likely XPrivacy-LUA, Google Services. Uncheck some of them.

Oh man....the only thing holding me back is the safety net thing, and it looks like we have a work around tell someone has an actual method made for this phone. Not sure if I'm ready to actually mess with this yet...but thanks for the post, bro!

anubis2k3 said:
Oh man....the only thing holding me back is the safety net thing, and it looks like we have a work around tell someone has an actual method made for this phone. Not sure if I'm ready to actually mess with this yet...but thanks for the post, bro!
Click to expand...
Click to collapse
Didnt think it was that big of a deal to me. But it was fun with a new phone with nothing on it.

This was the Magisk module that worked to pass safety net for me. I didn't need any others.
Releases · kdrag0n/safetynet-fix
Google SafetyNet attestation workarounds for Magisk - kdrag0n/safetynet-fix
github.com
Google Pay "appears" to be working too. Haven't gone out and tried it yet though.

joemommasfat said:
Google Pay "appears" to be working too. Haven't gone out and tried it yet though.
Click to expand...
Click to collapse
That's the part that I use the most, and the reason I haven't rooted yet. Please let us know if it works. Much appreciated!

I can confirm that using google pay (newer GPay app) on my rooted 5a works at merchants. I've already used it several times over the last week or so with no problems.

Deadmau-five said:
3. When that didn't work, I installed these both using Magisk from this post:
Click to expand...
Click to collapse
Why? Isn't the shim version just for Samsungs? Either way, it's the same mod, just different versions.
Someone who actually knows what they're doing needs to write up a tutorial. Following instructions posted by people who have no idea what they're doing but "it works" for them is dangerous.

borxnx said:
Why? Isn't the shim version just for Samsungs? Either way, it's the same mod, just different versions.
Someone who actually knows what they're doing needs to write up a tutorial. Following instructions posted by people who have no idea what they're doing but "it works" for them is dangerous.
Click to expand...
Click to collapse
You're absolutely correct about the dangers in following instructions posted by who knows who. I'll go further and say when it comes to root and associated items stay away from anything posted on a site other than XDA. In many cases even if the instructions were correct at some point in time they may well be outdated now.
I haven't rooted yet for a few reasons yet but will, hopefully sometime very soon. In the meantime I can state the following:
They're is no need to modify props. Modifying props to identify as a different phone would only be required for custom ROMs that don't handle it themselves (or some non-certified Chinese phones, which doesn't apply here). If you're running stock just leave that portion alone. And, if I'm not mistaken (although not 100% certain) I think safetynet-fix takes care of that for you in any case.
You will definitely need kdragOn/safetynet-fix.
Hopefully that's all you need.
I'm not sure which version of Magisk you'll need. Unless you know what you're doing and how to get out of trouble I recommend staying away from the current alphas, they're extremely cutting edge and you can expect problems.
Best best is to check the following threads and see what's going on:
Actually see this post and the 2 posts immediately following
Magisk General Support / Discussion
This is the place for general support and discussion regarding "Public Releases", which includes both stable and beta releases. All information, including troubleshoot guides and notes, are in the Announcement Thread
forum.xda-developers.com
That should pretty much cover things for the moment. If nobody else (@hfam ?) has done it by the time I get around to rooting I'll write something up specific for the 5a.

I only mentioned what works for me since there was no step-by-step guide.
Dangerous how? Doing any mods to your phone is "dangerous". I fail to see how this is more so than others. Modifying your phone is risky.
If it didn't work I wouldn't have posted this guide. I only mentioned the steps that I took. It's not really a guide, just how I passed safety net.
But, my 5a has still been working great since then. GPay included.

jcmm11 said:
You're absolutely correct about the dangers in following instructions posted by who knows who. I'll go further and say when it comes to root and associated items stay away from anything posted on a site other than XDA. In many cases even if the instructions were correct at some point in time they may well be outdated now.
I haven't rooted yet for a few reasons yet but will, hopefully sometime very soon. In the meantime I can state the following:
They're is no need to modify props. Modifying props to identify as a different phone would only be required for custom ROMs that don't handle it themselves (or some non-certified Chinese phones, which doesn't apply here). If you're running stock just leave that portion alone. And, if I'm not mistaken (although not 100% certain) I think safetynet-fix takes care of that for you in any case.
You will definitely need kdragOn/safetynet-fix.
Hopefully that's all you need.
I'm not sure which version of Magisk you'll need. Unless you know what you're doing and how to get out of trouble I recommend staying away from the current alphas, they're extremely cutting edge and you can expect problems.
Best best is to check the following threads and see what's going on:
Actually see this post and the 2 posts immediately following
Magisk General Support / Discussion
This is the place for general support and discussion regarding "Public Releases", which includes both stable and beta releases. All information, including troubleshoot guides and notes, are in the Announcement Thread
forum.xda-developers.com
That should pretty much cover things for the moment. If nobody else (@hfam ?) has done it by the time I get around to rooting I'll write something up specific for the 5a.
Click to expand...
Click to collapse
Just a quick note to say I just finished with everything (new Pixel 5a 5G, rooted + Safety net, restored all my apps, etc) and it's a flawless victory, ALL banking apps work great, SafetyNet passes, no hiccups.
I'd be happy to craft up a step by step and post it if there's some interest. It's not often I get to give back to this outstanding community, so it's the least I can do jumping on the opportunity. UFC 266 Main card is just starting, so I'll get started right after the fight and post it here in this thread.
Great to see ya again @jcmm11! Coming back to root a new phone feels like a family reunion, so great to see many of you active folks still here helping out!!
hfam

Alright, as promised, here is my writeup for a step-by-step tutorial for rooting your new Pixel 5a and getting SafetyNet up and going. I know it looks like a book, but I wanted to put it into plain language and attempt to explain the process for everyone, even absolute first timers. I know when I first started I really appreciated when the person helping didn't presume I had any knowledge, so for those that may have some experience, sorry for the wordiness. I'll also include how I apply updates when a new Android security update is pushed out. I understand that there are now elegant ways to accept OTA updates, but that is out of the scope of this tutorial as I have always had issues with OTA, and have to catch up on how that works myself. I can attest to years of using this method though (using a full factory image) to perform the "monthly" security updates, and I have never had anything but full success, so I'll share that here below the rooting tutorial.
*Disclaimer and heads-up* this is for an UNLOCKED PIxel 5a purchased directly from Google Store. At the time of this writing that is the only place I'm aware of which currently offers the PIxel 5a. Once carriers like Verizon, etc, offer this device, there may be some changes to the process, so just know up front this is for the unlocked Pixel 5a*
*WARNING*! When you unlock the bootloader on your phone it WILL WIPE YOUR PHONE and reset it to factory. If you've already used your phone and set it up, you're going to lose that setup. If you can't bear it, then the rest of this isn't for you, as root cannot be achieved without unlocking the bootloader.
First, you'll need a few things
- https://developers.google.com/android/images
and download the latest FACTORY IMAGE for "barbet", which is the Pixel 5a. You want to download the SAME VERSION that is currently installed on your device. At the time of this writing, it's the September release.
From that same page, you will need the ADB+Fastboot platform tools which will allow you to perform the required tasks, download from this link:
- https://developer.android.com/studio/releases/platform-tools.html
I use Windows 10, and extract this tools download to a folder in the root of C: called "platform-tools". You will then need to add "c:\platform-tools" to your environment path.
On the Pixel 5a, you need to enable developer options. Go into Settings/About Phone/and tap "Build Number" 7 times. This enables developer options and it will let you know when you've unlocked this as you tap 7 times. Once developer options is unlocked, go back to Settings/System/Advanced, and you'll see Developer Options is now available.
Select Developer Options, and enable "USB Debugging" and also enable "OEM Unlocking".
(**NOTE** For now at least, until you decide how you want to proceed with handling updates in future (more on that later), I strongly recommend turning OFF "Automatic System Updates" as well, just a few items below "OEM Unlocking". This prevents any updates happening automatically on a phone reboot. You don't want to wake up and find an OTA update pushed out and removed root, or worse. You can always turn it back on later.)
Plug your phone into a USB port on your PC. Allow the PC to do it's thing. You can open up Computer Management on the PC (right click the windows menu button icon lower left of your toolbar and select "Computer Management". Select "Device Manager" on the left panel. You should see "Android ADB Device" appear at the top of the right pane list of devices. if not, then visit:
Install OEM USB drivers | Android Studio | Android Developers
Discover links to the web sites for several original equipment manufacturers (OEMs), where you can download the appropriate USB driver for your device.
developer.android.com
and download the appropriate USB driver for your system and retry the above directions.
First thing we have to do is unlock the bootloader.
On the PC, open a command prompt and change directory to "C:\platform-tools" as discussed above.
Now, type in "adb reboot bootloader". The phone will reboot into bootloader. (you may receive a dialog on the phone which says something to the effect of not recognizing the PC. Go ahead and allow it, check the box to allow it in the future, and proceed.
Phone is now at the bootloader, and shows you some info letting you know it's so, including that the bootloader is locked. Also, look at the Device Manager we opened earlier and confirm that you see Android ADB Device (or similar) which confirms your PC recognizes the phone and setup for ADB commands .
To unlock the bootloader, in the command prompt type:
fastboot flashing unlock
This will unlock the bootloader, you will likely see a warning that it's going to wipe the phone. Proceed and allow the unlock. The phone will then reboot and take you to your wiped phone just as you received it out of the box, except the bootloader is now unlocked and Developer Options are still available. Let the phone continue through it's first-time setup, and leave the phone plugged into the PC. If you unplugged no biggie, but we're going right back to the PC shortly and it will need to be plugged back in before the next step to accept the file we're going to push to it.
Now, you want to open a browser on the phone and go to (at the time of this writing, v23.0 is the current stable Magisk):
Release Magisk v23.0 · topjohnwu/Magisk
This release is focused on fixing regressions and bugs. Note: Magisk v22 is the last major version to support Jellybean and Kitkat. Magisk v23 only supports Android 5.0 and higher. Bug Fixes [App]...
github.com
Scroll down and under "Assets" select that Magisk 23.apk file, download and install it. Open Magisk if it doesn't open on install, and just let it sit, we're coming back to it shortly.
PATCHING THE BOOT.IMG FILE
On the PC, go back to the Factory Image you downloaded, and extract it to a temporary directory. You will see 6 files; a few "flash-all" files, a radio image, a bootloader image, and a ZIP file called "image-barbet-XXXXXXXXXXX.zip (the xxx's are whatever the version number is you've downloaded). Double click that ZIP file and you will see a dozen files. The one we need to root the device is "boot.img".
Copy (don't move!!) this file to c:\platform-tools. Now, go back to your command prompt (still pointing to c:\platform-tools) and type in:
adb push boot.img /sdcard/Download
Now back on the phone, within the Magisk app we left open, at the top where it says Magisk, choose to install. A dialog box will open, select Patch Boot File Image. Point the process to your /sdcard/Download, and select the boot.img file we just pushed there. Now allow it to patch the boot.img and Magisk will show you it's patching it, and in a moment tell you it was successful. Close the Magisk app, open "Files" and direct it to sdcard/Download. Note the name of the patched boot file, which is called "magisk_patched-XXXXX_xxxxx.img (the X's are the Magisk version, and the x's are 5 random chars). Feel free to leave it there as you go back to the PC...
Back on the PC, in the command prompt, now type:
adb pull /sdcard/Download/magisk_patched-XXXXX_xxxxx.img
make certain you get the name exact or it won't go, no worries, just get it correct. The file now resides in the "c:\platform-tools" directory along with the unpatched "boot.img" and your ADB+Fastboot tools.
Just about done rooting, here we go!
Now, in the command prompt type:
adb reboot bootloader
The phone reboots into bootloader. Now type:
fastboot flash boot magisk_patched-XXXXX_xxxxx.img (again, use the numbers and letters in YOUR patched file!)
Lastly, type:
fastboot reboot
Your phone reboots, and you should be rooted!! Unplug your phone from the PC, open up Magisk App and confirm, the Magisk entry at the top of the main Magisk App screen should now show you the version you installed, etc!
Time to get your banking apps (and any others that may detect unlocked bootloaders/root/etc) working!
In the Magisk App, on the bottom of the screen is a 4 item menu bar. Select the right-most icon, which is "Modules". At the top of the screen select "sorting order" and sort alphabetically. Scroll down to "riru" and select the module that is JUST "RIRU", (not any of the other "riru _______" modules). Choose to download it, then choose to install it. You'll be prompted to reboot the phone, so reboot the phone.
Next, we're going to install drag0n's Universal SafetyNet fix (at the time of this writing it's currently v 2.1.1) You will need to download this via a browser on your phone, so open a web browser and go to:
GitHub - kdrag0n/safetynet-fix: Google SafetyNet attestation workarounds for Magisk
Google SafetyNet attestation workarounds for Magisk - GitHub - kdrag0n/safetynet-fix: Google SafetyNet attestation workarounds for Magisk
github.com
On the right-hand side, you'll find "Releases", and v2.1.1 is the latest. Select that, then scroll down to "Assets" and download "safetynet-fix-v2.1.1.zip" By default this will download to sdcard/Download.
Go back into the Magisk App, select the "Modules" menu as above, and at the very top select the "Install from Storage" bar. Point to the file we just downloaded and install it (don't extract it, etc, it requires the zip exactly as downloaded and will do it's thing). Again, it will install the module and prompt you to reboot. Reboot.
Almost there!
At this point, if you havent installed your banking apps, do so. DON'T RUN THEM, just install them. I also have a Nintendo Switch Online app which failed because of root, so if you also have or want this app, install it now, again, do NOT run it yet, just install. Same with any other apps you are aware which have root/bootloader unlocked issues, get them installed, but don't run 'em.
Now, we're going to use MagiskHide to hide these apps and complete the process for passing SafetyNet and running apps which may not run due to root.
in the Magisk App, at that 4 item menu bar at the bottom, select the 2nd from left, or "MagiskHide". Select the MagiskHide item and it will open to a scan of all the apps on your system. By default I believe Magisk sets up to hide Google Play Services. You will see it selected, and all the other apps on your system unselected. Select each of the banking apps, the Nintendo Switch Online (if you have it), and any other apps that YOU ARE SURE will complain about unlocked bootloaders and/or root. Any onilne gaming that's popular are good choices, but again, it's easiest to NOT RUN them PRIOR to hiding them via MagiskHide. Pokemon GO comes to mind as one I've seen that needs hiding, etc, so make it easy on yourself and do a little research on any suspect apps prior to running them, then hide them if needed.
Anyhow, select your banking apps to hide them.
Now, we're going to check SafetyNet to make sure youll now pass.
On the Home menu in the Magisk App, select "Check SafetyNet". You will be prompted to download some proprietary SafetyNet shhhhhhhtuff....so let it download. Once done, SafetyNet check will open, and you should show a blue screen which says SUCCESS, and "basicintegrity" and "ctsProfile" will be checkmarked, evalType will show BASIC.
You're good to go, rooted, SafetyNet works perfect, and you can now open your banking apps and should open right up!!
If you find any specific issues about specific apps not working, or detecting root, etc, the best place to get help is in the Magisk General Discussion forum:
Magisk General Support / Discussion
This is the place for general support and discussion regarding "Public Releases", which includes both stable and beta releases. All information, including troubleshoot guides and notes, are in the Announcement Thread
forum.xda-developers.com
I owe those folks eternally for showing me what I know, and always having the answers for any issues I've ever had. Some of the nicest, smartest people Ive had the pleasure of knowing, they're always helpful, and even maintain fantastic sites for FAQ and chock full of great info about every aspect of Magisk.
BONUS ITEM: As I indicated above, I'd share the method I know, trust, and have used many many times, trouble free, to apply a system update to the phone without overwriting anything, and not hitting any issues many encounter using the OTA method (though I understand that's been vastly improved, I haven't educated myself as to that process and will likely continue to use this method).
Security Update (monthlies) Process using Full System Image
As above, download the newest Full Factory Image from the site. Extract this full image to a directory inside C:\platform-tools
In this directory, if you're on Windows, open the "flash-all.bat" file (don't run it, open it with Notepad or something similar, I really like Notepad++ as it's free, has a LOT of great functionality and, like the native Notepad, doesn't do any goofy formatting/fonting/etc when modifying and saving a file.)
In flash-all.bat, look for the "-w" entry in the fastboot command near the end of the file and REMOVE ONLY THE "-w", leaving the line correctly formatted (don't leave an extra space or something goofy), then save the file over the top of the original with the same name. This will remove the overwriting of your data when pushing the image, the "-w" tells the process to overwrite, so we remove it.
Open up a Windows Explorer and go to your c:\platform-tools directory. Delete (or move to another location) any "boot.img" files along with any "magisk_patched-XXXXX_xxxxx.img" files from previous operations. Also note and confirm that you have correctly extracted the latest Full System Image to it's own directory, residing in c:\platform-tools.
Now, connect your phone to the PC. Open your command prompt and point to "C:\platform-tools" again. Type: cd <name of Full system Image directory>
In command prompt, type:
adb reboot bootloader
The phone is now in bootloader. In command prompt, confirm you're pointing to "C:\platform-tools\<Full System Image extract dir>" Type:
flash-all
This will do a full factory image push to your phone, you'll see a couple quick writes and phone reboots, then begins writing the rest of the image to your phone, but since we removed the "-w" from "flash-all.bat", it's NOT overwriting your data, just the necessary system files to update it to the latest version!
Reboot your phone, let it do any optimizing and updating it needs to do, and don't run anything yet, we're not quite done, just let the phone settle in and finish booting and doing it's thing.
Now, go back and perform the steps above listed under "PATCHING THE BOOT.IMG FILE" to patch the newest boot.img from the Full System Image we just updated the phone with (push the boot.img to sdcard/Download, patch with Magisk App, pull magisk_patched-XXXXX_xxxxx.img to your PC, blast it back using fastboot), and you've now rerooted the phone.
Lemme just say again that I know this was a friggin' book, and I tried to make it as clear and plain language as I could to help even a first timer, so my apologies if it seems like an onerous process. It's really not, and once you've done this once or twice, it's a cakewalk and takes about 10 minutes of your time from start to finish to do the whole system update and reroot. Again, the newer methods to take OTA without losing root may be something you'd like to look into, i definitely will, but I'm very confident in sharing this method as I know it works like a champ and is foolproof if you take your time the first few times and make sure you do what's required (remove the "-w" from the flash-all.bat, etc)
Lastly, I've been using this method since the Pixel 2, and just performed it on my new 5a, it worked exactly as it has for years for me on the P2, so you can be confident moving forward that, if you follow instructions and take your time until it's all familiar, you'll be successful in rooting, passing SafetyNet, and applying system updates without screwing up the A/B slots or overwriting your data in the process.
I hope this helps even one person, and since I rarely find myself able to give back to the community in any real meaningful way (many of these folks are WAAAY beyond my modest skills and know so much!!), I hope that this provides some folks with a useful and meaningful tutorial, providing confidence that anyone can root their P5a (or about any Pixel it seems) without being a Magisk/Android prodigy.
@Didgeridoohan, @pndwal, @zgfg, @jcmm11, and so many others over the years have been so helpful, I couldn't have done any of this without their selfless help, so give those folks a big thanks also if this is any help to you.
Best of luck,
hfam

Thanks for the write-up @hfam, it's good to know that some of the steps that i tried aren't really necessary, like using props config or hiding the actual magisk app.
Appreciate you!

nsoult said:
Thanks for the write-up @hfam, it's good to know that some of the steps that i tried aren't really necessary, like using props config or hiding the actual magisk app.
Appreciate you!
Click to expand...
Click to collapse
Awww, thanks! Glad to do it and really hope it helps some folks tackle rooting their phones and passing SN!

Rooted with magisk v.23 - flashed zip as a module

So has anyone installed the October update yet?

GrandAdmiral said:
So has anyone installed the October update yet?
Click to expand...
Click to collapse
Yep, good to go. I used the same method I shared above.

Is this working with Android 12? Which Magisk version to use?

This method did not work for Android 12. I updated my rooted phone to android 12 OTA. It returned to stock. I followed the method above to patch the factory boot.img file with magisk. After flashing my phone in bootloader with the patched boot.img, my phone will not reboot. says:
failed to load/verify boot images
Any advice? My Magisk is v23. Do I need to use a beta version?

Poking around in this thread, it seems that android 12 root is a much more involved process, requiring factory wipe and additional steps.
[Guide] Flash Magisk on Android 12
Trying to root the Pixel 5 running Android 12 by flashing a magisk-patched boot image results in the phone only booting to fastboot mode ("failed to load/verify boot images") Some users have reported that booting (instead of flashing) the patched...
forum.xda-developers.com

tintn00+xda said:
This method did not work for Android 12. I updated my rooted phone to android 12 OTA. It returned to stock. I followed the method above to patch the factory boot.img file with magisk. After flashing my phone in bootloader with the patched boot.img, my phone will not reboot. says:
failed to load/verify boot images
Any advice? My Magisk is v23. Do I need to use a beta version?
Click to expand...
Click to collapse
As you stated, you are correct. You need to perform a full wipe or flash the factory image with a wipe and then root works fine and phone boots. Tried myself and works fine.