Related
So I flashed my phone to Phoenix and was going wonderfully. Flew into St. Louis from Oklahoma and the phone froze up. It's now stuck on the AT&T boot screen. Occassionally after doing a battery pull and turning it on, the Phoenix boot screen will come up and I've gotten it to the lock/unlock screen but is unresponsive to touch.
Occassionally it even has what almost looks like colorful static on the screen. So now I'm in a completely different state without my home laptop for a week with the Odin3 1 click and am unable to find a download link for it.
Help would be appreciated. I was hoping to get the phone into recovery to try and flash back to stock or reflash Phoenix but it just stays stuck on the AT&T boot screen now.
remove battery, put battery back in, hold up+down vol buttons, plug in usb.
you'll be at download mode, then use odin.
Chillyw said:
remove battery, put battery back in, hold up+down vol buttons, plug in usb.
you'll be at download mode, then use odin.
Click to expand...
Click to collapse
Do you have an Odin download link? The Odin link on the site isn't good anymore and google isn't helping
here's an alternative link I've used:
http://www.mediafire.com/?0w2y31maz8mdom4
I appreciate the help so far and the Odin link. I managed to get Odin downloaded. I managed to get my phone in download mode. However, Odin is not registering that there is any phone. Normally I'd see a COM but nothing is showing up.
I started by running Odin.
Then got my phone in download mode.
I can't get any farther.
Do you have the drivers installed on your PC ? I also read somewhere where you have to have the latest net frame work as well...If you do...you might have a bad usb cord...and here in St.Louis..there are a lot of AT&T stores you can get one..
Mac
Well, on the original thread that had the link for Odin has the 32/64 Samsung drivers. I downloaded the drivers zip file to the desktop of the laptop.
One thing I find strange is usually when I plug in the phone to my laptop with the USB cable, the option to view files, etc pops up. It is not on this laptop.
kiltedthrower said:
Well, on the original thread that had the link for Odin has the 32/64 Samsung drivers. I downloaded the drivers zip file to the desktop of the laptop.
One thing I find strange is usually when I plug in the phone to my laptop with the USB cable, the option to view files, etc pops up. It is not on this laptop.
Click to expand...
Click to collapse
Did you install the drivers then ? Sometimes my wife's Samsung laptop does that..and not install anything going to the desktop..If everything is loaded correctly..you 2 drive pop up windows should open..
Also (I'm sure it is) make sure usb debugging is checked on your phone..
Sometimes the most simplest things keeps things from working correctly..
Phone unplugged..in normal mode..usb debugging checked..do not mount phone..
Close Odin
Open Odin
Plug phone in
Put phone into download mode...click start...not master clear...
Mac
Odin is also finnicky about USB ports. If you are on a desktop machine, try using one in the back instead of the front, or if you have multiple sets, try using a different one. I've had Odin not recognize certain USB ports but recognize others before.
Finally, I suspect you already know this, but for sanity's sake make sure you start both the PC and phone up fresh after reboots, open Odin, then connect the phone. Connecting the phone first breaks Odin.
Mac11700 said:
Did you install the drivers then ? Sometimes my wife's Samsung laptop does that..and not install anything going to the desktop..If everything is loaded correctly..you 2 drive pop up windows should open..
Also (I'm sure it is) make sure usb debugging is checked on your phone..
Sometimes the most simplest things keeps things from working correctly..
Phone unplugged..in normal mode..usb debugging checked..do not mount phone..
Close Odin
Open Odin
Plug phone in
Put phone into download mode...click start...not master clear...
Mac
Click to expand...
Click to collapse
Plug the phone in after it is in download mode, otherwise odin might not see it.
Sent from my SGH-I897 using XDA App
skatcat31 said:
Plug the phone in after it is in download mode, otherwise odin might not see it.
Sent from my SGH-I897 using XDA App
Click to expand...
Click to collapse
I know...but I have had to do it this way on a couple of times..and let it go into download when it was hooked up already..It's strange..but it worked at that time..after getting the drivers loaded for the first time on the wifes laptop..
Mac
What OS are you running? Are you explicitly starting odin in administrator mode (right-click->run as administrator)?
Okay, so I switched USB ports and it suddenly recognized and it started to download drivers. But it was listed as a gadget Serial and no drivers found. Geez this would be so much easier if I was at home where the laptop is set up with everything instead of being several states away.
Okay, so apparently I do not have the correct drivers installed. I really appreciate all the help so far. At this point, should I just google Samsung Captivate drivers or does someone have a link handy?
I can't get to my debugging as the phone stays on teh AT&T boot screen. I did have it enabled before I left OKC though.
I've gotten teh Samsung modem software successfully installed.
opcow said:
What OS are you running? Are you explicitly starting odin in administrator mode (right-click->run as administrator)?
Click to expand...
Click to collapse
Phoenix 3.0 which is 2.2
The Odin is a zipfile that I have to use winzip to use it. It doesn't have the option to use as an administrator.
kiltedthrower said:
Phoenix 3.0 which is 2.2
The Odin is a zipfile that I have to use winzip to use it. It doesn't have the option to use as an administrator.
Click to expand...
Click to collapse
OS as in, what OS is your DESKTOP/LAPTOP running?
and....you need to EXTRACT Odin from the zip file, and run it as administrator
kiltedthrower said:
Phoenix 3.0 which is 2.2
The Odin is a zipfile that I have to use winzip to use it. It doesn't have the option to use as an administrator.
Click to expand...
Click to collapse
O_O You blew my mind.
Windows 7 is the OS and I finally got Odin extracted and running as administrator
opcow said:
O_O You blew my mind.
Click to expand...
Click to collapse
I know. Flying from OKC to St. Louis and then from St. Louis to Baltimore with a several hour layover has me exhausted and not thinking clearly.
I did manage to reboot it and Phoenix came up. All drivers were showing ready except for ADB and then the phone shut down and ADB said phone was unplugged.
I feel like I'm making headway but just not there.
And why is it I'm staying in an expensive hotel and you still have to pay for net? Geez
I downloaded the 64bit drivers. Ran the exe file.
Extracted Odin and have run it as an administrator
Put the phone in download mode.
Odin is still not seeing anything.
NM....pop up box just said taht device driver software not successfully installed. I think I'm going to hit my head against the wall for a bit.
Alright, so I was having some problems with my cognition rom and decided go back to stock so I could flash the new cognition. I put my phone into download mode, and it took a few times for ODIN to see my phone. After I got ODIN to see my phone I tried to master clear, it did not work. I had to pull the battery out and try again. I rebooted my phone again, and many program errors came up. I shut off my phone, tried to get into download mode and it wouldn't let me using the volume down + up then insert USB with ODIN open.
Now to get into download mode I must hold buttons with battery out, put USB in, and put battery in and I get download mode instantly, but I cant get ODIN to recognize my phone at all anymore. I tried many different methods(odin open before DL mode, odin closed before download mode, etc). I looked through a few threads and couldnt find anything that would work. Also my window 7 64 now says it doesn't recognize the USB device when I plug it in. Whats going on with my phone?? Im getting very annoyed! Is there any way to go back to stock besides ODIN??? Any help is appreciated!!
***UPDATE***
Seems like I may have a 3 button combo lock, and no USB support of any kind(besides charging).
UPDATE: I used rom manager to flash over my old rom. My phone works again, but it wont go into download mode at all now. Only when I use the cognition menu to send it to download mode will it work. I still cant get ODIN to see my phone. I want to go back to stock still, but without ODIN working, can I?
ziphoward said:
UPDATE: I used rom manager to flash over my old rom. My phone works again, but it wont go into download mode at all now. Only when I use the cognition menu to send it to download mode will it work. I still cant get ODIN to see my phone. I want to go back to stock still, but without ODIN working, can I?
Click to expand...
Click to collapse
under your captivate battery, there is a number like 1008, 1010, what is yours?
I've had the same trouble with download mode + odin on my Windows 7 64 bit pc too.
I have to have odin running, phone off with battery out, and usb cable in. I leave the battery out for about a 10 second count. Then put the battery in and hit all the buttons at the exact same time (power + volume up and down). The key here is that I only had to hit all three buttons momentarily to get it to go into download mode. I didn't have to hold them down for any length of time.
I easily spent 1 hour trying to get odin to work the last time I had to reflash to stock. Only because I forgot how hard it was three last time with my 64 bit machine.
Sent from my SAMSUNG-SGH-I897 using Tapatalk
mengbo said:
under your captivate battery, there is a number like 1008, 1010, what is yours?
Click to expand...
Click to collapse
1006
So should I just keep trying to get into ODIN by just fiddling around with it? Ive tried an XP machine and it wouldnt work either. Does booting into download mode from the cognition power menu any different than entering download mode the manual way? Every time I put the battery in with the USB it takes me to the battery charger screen. At first with that issue, putting in the battery last while holding down volume up and down, would put the phone into download mode(as opposed to the normal ways of getting into download mode). Now that wont even work at all.
first you can try the 3 button fix, just search the forum for that.
you may need to build a jig or buy one online just in case, it will get you into the download mode easily.
http://cgi.ebay.com/ws/eBayISAPI.dl...47234&ssPageName=STRK:MESELX:IT#ht_511wt_1139
im having horrible trouble with adb cmd. I installed the samsung drivers, put my phone in usb debugging, did some tutorials on how to install sdk correctly, went to the correct file paths in cmd promt, and still cant access the adb shell. Any pointers on this?
Also, could I wipe all data off internal storage and use the "reinstall package" option in recovery mode to use rom manager update.zip to restore my rom from my sd card? Im not sure if thats possible. Im getting errors with my rom, and it feels slower since I just reinstalled over the top of my faulty rom.
Seems the only usb function I have right now is to charge it. Hmmm USB brick?
Any help out there???
3g stopped working on my phone when I woke up. I really need to get a fresh rom installed.
If I recall correctly, the path to where adb is had changed. Check all folders inside the sdk folder. to make my life easier, I put the sdk folder right into the root directory (c and renamed it sdk. Don't know if that well help or not...
Sent from my SGH-I897 using XDA App
I changed the folder to androidsdk from whatever it was.
bueller bueller bueller...anyone?
Well, if your phone is a rev 1006 you "should" have a problem like losing your button combo. I guess that could have happened but I doubt it, I've got a 1007 and never lost it.
So, as for ADB here's what I do. Take the android SDK folder you downloaded and look inside it. There is a folder called tools. I take the tools folder and copy it to the root of my C: drive. Make sure you have all the drivers loaded, speaking of which I would uninstall and reinstall the drivers. Sounds like they flaked out for some reason. Next open up a cmd window, Start > Run > CMD.
Then type,
cd /
cd tools
adb devices <<this shows if your phone is recognized. if it is...
adb reboot download
*or
adb reboot recovery
*or
adb shell
For what it's worth, I have been flashing my phone since I got it in July and the only time I Master Clear is when I have had a problem like a soft brick or something that I was suspicious about the data on my internal SD. Which, so far has been maybe 3 times. I don't think necessary to Master Clear every time you flash to stock.
Also, you shouldn't really have to the pop out the batter to do the download mode trick. I turn my phone off, hold both Vol up and down, then plug in USB and I'm in download mode.
bobbylx said:
Well, if your phone is a rev 1006 you "should" have a problem like losing your button combo. I guess that could have happened but I doubt it, I've got a 1007 and never lost it.
So, as for ADB here's what I do. Take the android SDK folder you downloaded and look inside it. There is a folder called tools. I take the tools folder and copy it to the root of my C: drive. Make sure you have all the drivers loaded, speaking of which I would uninstall and reinstall the drivers. Sounds like they flaked out for some reason. Next open up a cmd window, Start > Run > CMD.
Then type,
cd /
cd tools
adb devices <<this shows if your phone is recognized. if it is...
adb reboot download
*or
adb reboot recovery
*or
adb shell
For what it's worth, I have been flashing my phone since I got it in July and the only time I Master Clear is when I have had a problem like a soft brick or something that I was suspicious about the data on my internal SD. Which, so far has been maybe 3 times. I don't think necessary to Master Clear every time you flash to stock.
Also, you shouldn't really have to the pop out the batter to do the download mode trick. I turn my phone off, hold both Vol up and down, then plug in USB and I'm in download mode.
Click to expand...
Click to collapse
Im having USB driver problems, windows 7 will not recognize my phone. I think this is why adb wont recognize my phone correct? I can only get into download mode now but using the power menu thats custom from Cognition. Is my phone screwed?? Can I flash a ROM without ODIN?
ziphoward said:
Im having USB driver problems, windows 7 will not recognize my phone. I think this is why adb wont recognize my phone correct? I can only get into download mode now but using the power menu thats custom from Cognition. Is my phone screwed?? Can I flash a ROM without ODIN?
Click to expand...
Click to collapse
Like I said, have you tried uninstalling the drivers from windows and reinstalling them? I am running Win 7 x64 and have had that happen. After i flash a rom or flash to stock sometimes windows doesn't recognize my phone at all. The first time I just used my laptop to flash but the second time I uninstalled the drivers and reinstalled. It's also important that you plug into the USB ports directly on the motherboard on the back of your PC. There are known problems when trying the front usb ports or through a hub.
bobbylx said:
Like I said, have you tried uninstalling the drivers from windows and reinstalling them? I am running Win 7 x64 and have had that happen. After i flash a rom or flash to stock sometimes windows doesn't recognize my phone at all. The first time I just used my laptop to flash but the second time I uninstalled the drivers and reinstalled. It's also important that you plug into the USB ports directly on the motherboard on the back of your PC. There are known problems when trying the front usb ports or through a hub.
Click to expand...
Click to collapse
Ive tried uninstalling and reinstalling many many times. I am using a laptop and ive tried all the USB ports but still no luck. I hate having my phone like this, it will drive me insane until its fixed.. or officially considered usb bricked.
ziphoward said:
Ive tried uninstalling and reinstalling many many times. I am using a laptop and ive tried all the USB ports but still no luck. I hate having my phone like this, it will drive me insane until its fixed.. or officially considered usb bricked.
Click to expand...
Click to collapse
Just curious, is it a Dell laptop? My Dell never recognizes my phone unless I power the laptop on with the phone/USB plugged in. If the laptop is on, and I plug phone in it never works, so I leave it plugged in and reboot and it works. It drives me crazy, but whatever it's my work PC.
bobbylx said:
Just curious, is it a Dell laptop? My Dell never recognizes my phone unless I power the laptop on with the phone/USB plugged in. If the laptop is on, and I plug phone in it never works, so I leave it plugged in and reboot and it works. It drives me crazy, but whatever it's my work PC.
Click to expand...
Click to collapse
It is a dell actually, but I just tried your method and it didnt work for me. Thanks for the input though!
Alright, I downloaded kies mini today and it actually installed some drivers correctly. I was able to pull up my internal drive on the computer, but it wouldn't read it. I was able to get ODIN to see my phone(first time in weeks), but it only shows up when my phone is NOT in debugging mode. So im assuming Master Clear will work now. I was using AIO captivate tool box, and my phone rebooted at the click of the button into download mode, but once again it wont see my phone in ODIN while in download mode. Im getting closer!
Why wont ODIN recognize my phone with USB debugging on? Any more suggestions on how to make this happen?
My computer doesn't recognize my phone right now and it is soft bricked. Is this normal or no?
That all depends on what is currently on your screen. If it's the phone>--<computer screen, that's basically like download mode. Otherwise you will probably need to try to boot into recovery or download mode. Add more details and we can come up with a better solution
yeah it is at the phone>--<computer screen. No button combination is working to get it to download mode or recovery. I need a jig. I want to know if my computer will read the phone ones it is in download mode.
It will read it now. Just plug it into Odin or a heimdell oneclick
Sent from my SGH-I897 using XDA App
Nope. I tried both of those. My computer is not reading a device. Not even an unknown device. I have tried 2 computers and multiple ports and a second USB cable.
Ya I'm talking about Odin or heimdell...not your computer. Everyone here will tell you it will work and its been done a million times. But ok
Sent from my SGH-I897 using XDA App
jaymonster138 said:
My computer doesn't recognize my phone right now and it is soft bricked. Is this normal or no?
Click to expand...
Click to collapse
I understand u r asking about ur computer recognizing ur phone, but this should still be of some help... Captivate Connection Issues and Download Mode Help.
And if your soft brick/firmware upgrade fail screen looks like this View attachment 857512 (this is pre gingerbread), then it has been reported to be recognized by some in Heimdall and/or Odin as a Download mode screen and therefore they were able to get back to a Stock or otherwise fixed state. But if Odin or Heimdall does not recognize this for you, then u will have to try a Jig.
If it looks like this View attachment 857513 (this is since gingerbread), then it is definitely an alternate Download mode screen and will be recognized by Heimdall and/or Odin and you can get back to a working state.
All either of these screens mean is that your "upgrade failed, so reconnect the phone to pc and try again."
So I was flashing a stock rom from Odin, and Odin froze, so I unplugged the phone and took out the battery. Now, when I try to get into download mode, all I get is a screen with a phone-!-computer. Even with a usb jig, it just goes to this screen. My captivate is also not recognized by the computer when I plug it in when its on the phone-!-computer screen.
cherrybombaz said:
So I was flashing a stock rom from Odin, and Odin froze, so I unplugged the phone and took out the battery. Now, when I try to get into download mode, all I get is a screen with a phone-!-computer. Even with a usb jig, it just goes to this screen. My captivate is also not recognized by the computer when I plug it in when its on the phone-!-computer screen.
Click to expand...
Click to collapse
Have you tried all the steps in the Captivate Connection Issues post (in my signature)?
Does it say something about hardware upgrade failure?
mrhaley30705 said:
Does it say something about hardware upgrade failure?
Click to expand...
Click to collapse
Nope. It just doesn't show up at all; not even in device manager and it just shows the phone exclamation computer screen.
jmtheiss said:
Have you tried all the steps in the Captivate Connection Issues post (in my signature)?
Click to expand...
Click to collapse
Yea more or less. The weird thing is it was detected before and odin was able to start the flash. But it hung after it said do not disconnect the device so I was forced to unplug it. Now I just don't see anything at all.
cherrybombaz said:
Yea more or less. The weird thing is it was detected before and odin was able to start the flash. But it hung after it said do not disconnect the device so I was forced to unplug it. Now I just don't see anything at all.
Click to expand...
Click to collapse
Have you given Heimdall a try? It sometimes works when Odin won't.
jmtheiss said:
Have you given Heimdall a try? It sometimes works when Odin won't.
Click to expand...
Click to collapse
Yep. When I try to install the heimdall driver, the phone doesn't even show up so it won't install.
cherrybombaz said:
Yep. When I try to install the heimdall driver, the phone doesn't even show up so it won't install.
Click to expand...
Click to collapse
Odd. I'm assuming you've done all the uninstalling drivers, rebooting, etc, etc?
jmtheiss said:
Odd. I'm assuming you've done all the uninstalling drivers, rebooting, etc, etc?
Click to expand...
Click to collapse
Yea I tried uninstalling and reinstalling the Odin drivers. How do I uninstall the heimdall driver?
Driver Uninstallation Instructions:
1. Put your Samsung Galaxy S Captivate (i897) into download mode by holding Volume Down + Volume Up and...
2. Plug your phone into your PC.
3. Open up Device Manager on your PC.
4. Under "Libusb (WinUSB) devices" right click on "Samsung USB Composite Device" and choose Properties.
5. Go to the Driver tab and select Uninstall.
Done
4-2ndtwin said:
Driver Uninstallation Instructions:
1. Put your Samsung Galaxy S Captivate (i897) into download mode by holding Volume Down + Volume Up and...
2. Plug your phone into your PC.
3. Open up Device Manager on your PC (Control Panel -> System -> Device Manager).
4. Under "Libusb (WinUSB) devices" right click on "Samsung USB Composite Device" and chose Properties.
5. Go to the Driver tab and select Update Driver.
6. Chose to browse your computer for the driver.
7. Chose to pick from a list of devices drivers on your computer.
8. Pick the original Samsung Composite driver, press next and then follow the prompts.
9. Done
Click to expand...
Click to collapse
The problem is I don't see my phone in device manager.
Edited my previous post. Gave u the update instead of the uninstall method, oops.
4-2ndtwin said:
Edited my previous post. Gave u the update instead of the uninstall method, oops.
Click to expand...
Click to collapse
But I don't see the Libusb tab in device manager when I plug my phone in.
When u initially installed the drivers for Heimdall, they only installed to the usb port that u were connected to. So u need to be plugged into that specific port and then u should see it in the Device Manager.
And u really don't need to uninstall the drivers that u need for Heimdall, as long as u installed them after u installed the drivers from Kies. See this post... http://forum.xda-developers.com/showpost.php?p=19998299&postcount=115
And if u have tried everything in the Stickied thread--Captivate Connection Issues and Download Mode Help to no avail, then ??
4-2ndtwin said:
When u initially installed the drivers for Heimdall, they only installed to the usb port that u were connected to. So u need to be plugged into that specific port and then u should see it in the Device Manager.
And u really don't need to uninstall the drivers that u need for Heimdall, as long as u installed them after u installed the drivers from Kies. See this post... http://forum.xda-developers.com/showpost.php?p=19998299&postcount=115
And if u have tried everything in the Stickied thread--Captivate Connection Issues and Download Mode Help to no avail, then ??
Click to expand...
Click to collapse
Yep I made a jig and it works but it doesn't go to the downloading screen with the shovel instead it just goes to the screen with the phone exclamation computer.
Then try this...may sound odd but anyway--just pull ur battery and leave it out for 5 minutes or so and then put it back in and try getting back into download mode and see what happens.
Btw, which stock odin were u trying that got u in this mess ?
4-2ndtwin said:
Then try this...may sound odd but anyway--just pull ur battery and leave it out for 5 minutes or so and then put it back in and try getting back into download mode and see what happens.
Btw, which stock odin were u trying that got u in this mess ?
Click to expand...
Click to collapse
The odin3 one click downloader. Yep I tried taking out the battery -- no go :/.
happened to my cappy yesterday. went through 7 hours to fix mine. had the same issue as yours. no download mode showing with any combo I try even recovery had 4 micro usb cables and still my pc is choosy. that screen is actually download mode. you just need the proper drivers for the pc to read it. I used the one from heimdall. tried for atleast 100x before my pc recognizes my cappy as gadget serial and then boom! after installing,uninstalling and reinstalling all is A-ok now. just try it and have faith on your cappy
gonemad02 said:
happened to my cappy yesterday. went through 7 hours to fix mine. had the same issue as yours. no download mode showing with any combo I try even recovery had 4 micro usb cables and still my pc is choosy. that screen is actually download mode. you just need the proper drivers for the pc to read it. I used the one from heimdall. tried for atleast 100x before my pc recognizes my cappy as gadget serial and then boom! after installing,uninstalling and reinstalling all is A-ok now. just try it and have faith on your cappy
Click to expand...
Click to collapse
What did you try before it was recognized? Did you just plug and replug the usb into the computer until it worked?
Mine did this before, when I accidently forgot to convert back to RFS before flashing back to stock, and I thought I was totally screwed. After this screen comes up the first time it will not go away, even if a download jig is used, until you get a good flash.
Try this:
Open your Odin, and have it ready with whatever you were trying to flash to begin with. Pull the battery on your phone, put your download jig in, and now put your battery in. It will still be the error screen that comes up. Pull your jig, and now plug your phone in. It should show on Odin now, and this flash should take correctly.
---------- Post added at 01:53 AM ---------- Previous post was at 01:50 AM ----------
Also make sure the USB port you are using is a direct link to your board. I always use one of the original USB 2 ports on the back of my computer. Not using a USB hub either, but straight from the port to your phone.
Okay.
I bought a Samsung Captivate from a company on Amazon a few weeks ago, and it started having the problem with the speaker cutting out. I took it apart to try the two fixed I'd googled - loosening the speaker screw and reseating the speaker ribbon - and neither worked, and now the speaker is completely dead. That isn't my biggest problem, though.
Somehow in the process of the above, I did something that made it so that the phone will only boot into download mode. I can hold down the power and volume buttons and get it to reboot, but it only reboots into download mode again, and won't recognize in windows via the USB cable. It did recognize once, and I used Odin3 to get it back to a factory reset image (it was running stock firmware, but I'd rooted it to remove the AT&T apps) thinking in vain that it might help, but it still only boots into download mode.
But there's the weird thing: It won't power off in download mode unless I pull the battery out, but if I put it back in then plug in the USB cable while holding both volume buttons, it boots right into android, no problem. Everything's fine except the speaker still doesn't work, it doesn't show to be charging while plugged into the USB cable, and still won't recognize the USB in Windows. But if I turn the phone off and back on, I'm back in non-recognizing download mode again.
Everything otherwise works fine once I get it into android, I can even tell it to erase all settings and factory reset, and it reboots itself, re-flashes to stock, and works fine until I power off and back on, then back to download mode.
So I guess the question is oh god what have I done?
Freud,
I too am having this issue with my roommate's phone. The only way I can get it to boot is if I perform a restore using a Odin3 image. However once it's turned off it only boots into download mode. I nor the roommate have opened the phone. It just one day decided to keep booting into download mode.
Any asistance in this matter would be appreciated! Thank you.
zeyoner said:
Freud,
I too am having this issue with my roommate's phone. The only way I can get it to boot is if I perform a restore using a Odin3 image. However once it's turned off it only boots into download mode. I nor the roommate have opened the phone. It just one day decided to keep booting into download mode.
Any asistance in this matter would be appreciated! Thank you.
Click to expand...
Click to collapse
i have the same problem! the only way to boot my sgs is to flash a stock rom with odin. and every time i turn off the phone then it reboots in download mode!! someone has a fix? i need help!!! thanks
Pink Freud said:
Okay.
I bought a Samsung Captivate from a company on Amazon a few weeks ago, and it started having the problem with the speaker cutting out. I took it apart to try the two fixed I'd googled - loosening the speaker screw and reseating the speaker ribbon - and neither worked, and now the speaker is completely dead. That isn't my biggest problem, though.
Somehow in the process of the above, I did something that made it so that the phone will only boot into download mode. I can hold down the power and volume buttons and get it to reboot, but it only reboots into download mode again, and won't recognize in windows via the USB cable. It did recognize once, and I used Odin3 to get it back to a factory reset image (it was running stock firmware, but I'd rooted it to remove the AT&T apps) thinking in vain that it might help, but it still only boots into download mode.
But there's the weird thing: It won't power off in download mode unless I pull the battery out, but if I put it back in then plug in the USB cable while holding both volume buttons, it boots right into android, no problem. Everything's fine except the speaker still doesn't work, it doesn't show to be charging while plugged into the USB cable, and still won't recognize the USB in Windows. But if I turn the phone off and back on, I'm back in non-recognizing download mode again.
Everything otherwise works fine once I get it into android, I can even tell it to erase all settings and factory reset, and it reboots itself, re-flashes to stock, and works fine until I power off and back on, then back to download mode.
So I guess the question is oh god what have I done?
Click to expand...
Click to collapse
I can only offer a solution to the windows connection issue, once the phone is connected to pc, go into device manager and uninstall drivers for whatever it sees, unplug phone then plug back in and windows should reinstall drivers. Worked for me, odin wouldnt see phone . GL
This will solve your speaker issue
http://www.ebay.com/sch/i.html?_trksid=p5197.m570.l1311&_nkw=samsung+i897+speaker&_sacat=0
And this should solve your download mode issue
http://forum.xda-developers.com/showthread.php?t=1300843
I'm having a similar issue where my PC does not recognize the device. Right now I have no ROM installed, I have Devil Recovery, and I can only boot into recovery and Download Mode. However 2 different PC's will not recognize the phone. I've tried multiple cables and one PC was Windows 8, one was Windows Vista. Both had the most recent drivers installed. Nothing works....any clue? I can't mount the /sdcard or USB Storage while in recovery because the PC doesn't pick up the phone. The internal storage doesn't have a ROM or kernel to flash on it neither so I cannot flash anything. I have a captivate that has Devil Recovery and can boot into download mode but will computers will not recognize the device, drivers installed or not.
Jonnyredcorn said:
I'm having a similar issue where my PC does not recognize the device. Right now I have no ROM installed, I have Devil Recovery, and I can only boot into recovery and Download Mode. However 2 different PC's will not recognize the phone. I've tried multiple cables and one PC was Windows 8, one was Windows Vista. Both had the most recent drivers installed. Nothing works....any clue? I can't mount the /sdcard or USB Storage while in recovery because the PC doesn't pick up the phone. The internal storage doesn't have a ROM or kernel to flash on it neither so I cannot flash anything. I have a captivate that has Devil Recovery and can boot into download mode but will computers will not recognize the device, drivers installed or not.
Click to expand...
Click to collapse
Have you tried to uninstall the current drivers, reboot pc and reinstall them?
Also, it could be devil kernel that is faulty. If Odin can recognize the phone, you could flash a different kernel. Or even flash stock KK4, then corn kernel and finally, the ROM you wanna flash through recovery.
I just cannot get the PC to recognize the phone at all, even in download mode. I've tried 2 pc's and multiple USB cables, samsung, non-samsung, motorola, universial. Nothing, just says USB cannot recognize this device. Reinstalled drivers on 2 pc's and rebooted several times. I am lost, I know I'm not bricked because I can access download mode and recovery. I do not have a ROM on my internal card so I can't flash a ROM and can't mount my phone to my PC. No clue what to do.
---------- Post added at 02:59 PM ---------- Previous post was at 02:10 PM ----------
I just need my PC to recognize my device and I'd be good, odin would then recognize my device in download mode and I could flash a different kernel or rom.
Try cleaning out the micro usb port of ur phone. Maybe the contacts are not making good contact.
Sent from my SAMSUNG-SGH-I777 using xda premium
Any recomendations for what to use to clean it out? I have q-tips, any special solution to use or just the q-tip?
Rubbing alcohol should do.
Sent from my SAMSUNG-SGH-I777 using xda premium
Still no luck...I got my PC at work to recognize the phone ONCE. It went through and recognized it like it normally would, however it wouldn't recognize it again. I've been trying on my PC at home all last night and all morning and still no go. It won't recognize it. Now one thing I thought about is that I am on Windows 8. The PC at work that recognized it was Windows Vista. I don't know if that has anything to do with it. I wouldn't care so much if I didn't just sell it for $150 I just wanted to give the person a more updated ROM and ended up screwing something up when flashing the ROM.
Jonnyredcorn said:
Still no luck...I got my PC at work to recognize the phone ONCE. It went through and recognized it like it normally would, however it wouldn't recognize it again. I've been trying on my PC at home all last night and all morning and still no go. It won't recognize it. Now one thing I thought about is that I am on Windows 8. The PC at work that recognized it was Windows Vista. I don't know if that has anything to do with it. I wouldn't care so much if I didn't just sell it for $150 I just wanted to give the person a more updated ROM and ended up screwing something up when flashing the ROM.
Click to expand...
Click to collapse
Ok so I know you've uninstalled and reinstalled drivers several time. But what drivers are you using and when you plug the phone into your pc what is it showing as in the device manager?
They may be exactly what you are using but I added some drivers to this post you might want to try. Just unzip then through device manager update the drivers for your device manually and point it to that folder.
I added these drivers because I'm on Win8 as well and I noticed when I was in recovery that my phone wasn't showing up correctly in the device manager. After installing these drivers it was.
Thanks I'll try that when I get home, I am using the most recent drivers on the Samsung website for the Captivate.
So I got it to boot and be recognized by my computer and I used a 1 click method with CWM and it passed so the Odin flash. So no I basically have a on rooted captivate running 2.5 gingerbread and it is totally sellablebel now. I have no idea what caused my computer to recognize it I didn't even try your drivers yet, but thanks for trying to help.
Sent from my Nexus 10 using Tapatalk 2
Well whatever happened I'm glad you got it up and running.
Sent from my SGH-I897 using xda app-developers app