Hello fellas,
I replaced my note 5 lcd before 4 days it was working perfect w/out any flaws but it suddenly went black while using it was full charged while it happend. but i can receive calls texts hear sounds. I tried a youtube fix by holding Vol down+Power!! Yes it does reboot the phone but whateva happens lcd is black, even i tried to flash stock rom also its succeed!!
I dont know what the problem is but my lcd was broken before, while in that stage it cannot boot or receive calls there was only a solid blue led.
But in this case i dont know what the problem is and i think you might help me figure out.
Thanks.
Ahmed Safeek said:
Hello fellas,
I replaced my note 5 lcd before 4 days it was working perfect w/out any flaws but it suddenly went black while using it was full charged while it happend. but i can receive calls texts hear sounds. I tried a youtube fix by holding Vol down+Power!! Yes it does reboot the phone but whateva happens lcd is black, even i tried to flash stock rom also its succeed!!
I dont know what the problem is but my lcd was broken before, while in that stage it cannot boot or receive calls there was only a solid blue led.
But in this case i dont know what the problem is and i think you might help me figure out.
Thanks.
Click to expand...
Click to collapse
I had the exact same problem and unfortunately the phone had to be replaced under warranty so if you don't have a warranty on the phone then immediately contact whoever sold you the screen and get a replacement since that one's broken. It's not going to come back no matter what and it was probably a cheap knock off which is all I keep seeing all over the place but try anyway because they aren't cheap at all!!!
Sounds like when you had the LCD replaced they didnt do the digitizer ( that is the component that converts the signal to pictures for display on the screen) usually when one is damaged they are both replaced at the same time
gmfirebird said:
Sounds like when you had the LCD replaced they didnt do the digitizer ( that is the component that converts the signal to pictures for display on the screen) usually when one is damaged they are both replaced at the same time
Click to expand...
Click to collapse
I think you're a bit confused on what a digitizer is... It's not for converting pictures it's for dealing with the touch part of it I.E it senses where your fingers are on the screen.
Related
Hey guys,sorry for bringing this up.
Whenever i dial,screen goes black and doesn't come back on.
If i place it flat on a table,then it gets lit but as soon as i rotate the device it goes black again.
My HD7 recently started having this problems...
It started happening after i replaced the micro sd inside with a bigger one.
So my concern is that somehow it moved or got dust when i removed the back plastic cover? Where is it placed anyway?
I tried hard resetting 2 times but nothing works. It would be cool if there was a registry or app to take control of it. Can somebody help?
PS. i cannot send it back because i live in Albania (no official htc shops either around here)
Thanks!
Hello,
The proximity sensor is located on the top left of the device, you can see it when viewed under a bright light. Have you applied any screen protectors which can interfere with them? Replacing the sd card should not have any effect on the proximity sensor. When you rotate the device when the call is placed, the screen should go black by default cause of the sensor
@rhn thank you for your reply.
My phone does not have any screen protector or cover of any kind. Also,if i rotate it while in call it still remains black. As soon as i press the call button,screen goes black and wont come back until the call is ended by the person on the other side.
Really really annoying... Oh sometimes it even flashes after the call has ended...
Sounds like a hardware fault ...have you tried updating your rom?You can find a compatible rom in the rom development subforum..
Yep,tried that too. Just updated today and still the same issue.
It also happened after i changed the micro sd,so maybe something has moved in there. There's no other way than try to open the device and check it out,i guess :/
If you can think of something else,let me know
Warranty
Warranty replacement worked for me.
http://forum.xda-developers.com/showthread.php?t=864311
Thanks bofett, i cannot get a replacement. Warranty for this phone was for 5 days!!! (stupid i know....i totally regret picking it up) So that means i'm screwed...
Thank god i still have my great HD2 so i can start opening this phone without fear
last night my x1s screen was going all fuzzy like different colours and cut out a few times. now today notthing. the screen is blank. backlight comes on i think. the phone starts up normal as i can hear the start up sound and i can accept calls. i think this is failure of the felx cable. Is this true? and if so is i worth get on and fiting it myself or going to a repair shop. im on the cheap here so any fix will do.
rocklobster666 said:
last night my x1s screen was going all fuzzy like different colours and cut out a few times. now today notthing. the screen is blank. backlight comes on i think. the phone starts up normal as i can hear the start up sound and i can accept calls. i think this is failure of the felx cable. Is this true? and if so is i worth get on and fiting it myself or going to a repair shop. im on the cheap here so any fix will do.
Click to expand...
Click to collapse
I have had the second part of your problem before where screen doesn't come on but the back light and everything else works. A couple of months back when I was at college I dropped my phone really hard at a party( I was wasted ) and the next morning the screen wouldn't come on. So what I did was I looked up the guide to how take the X1i apart and luckily one of my buddies had the same screwdrivers that I needed because he uses it on his the Blackberry Storm 2. So what I did was went to where the Flex ribbon cable was located unattached it, then reattached it, and put my phone back together and the screen came back on and still works to this day. If this helps press thanks.
http://forum.xda-developers.com/showthread.php?t=535664
i'm having a Problem too.
the to lines in the top of my screen are blue ^^
i think its a problem with the connection, but as it isn't really big and i don't have a newer phone i will dissasemble it later ;-)
please replace the * with t,or copy it without h**p:// (can't post outside links yet ^^)
h**p://a6.sphotos.ak.fbcdn.net/hphotos-ak-ash4/296861_222070397844215_100001237692896_682738_4498500_n.jpg
About a couple weeks ago I cracked the digitizer(touch screen) on my Lg Thrill and replaced it. Before doing this everything was fine with the phone...I upgraded to GB and it is also rooted but like I said everything was working just fine until I replaced the digitizer. Now every time I make or receive a phone call the phone goes black like it was close to my ear. This only happen if I answer the call and if I make a call it happens right away.The phone is still on and the calls go through but the phone goes black and is useless and I can't even hang it up until the other person hangs up. Not even pressing the power button on the top helps. I have checked and nothing is blocking the sensor on the front of the phone and the new digitizer I got from ebay but again it is a perfect fit and nothing is blocking the sensors...Any Ideas or suggestions? anything would be a great help thank you!
ZombieWarez said:
About a couple weeks ago I cracked the digitizer(touch screen) on my Lg Thrill and replaced it. Before doing this everything was fine with the phone...I upgraded to GB and it is also rooted but like I said everything was working just fine until I replaced the digitizer. Now every time I make or receive a phone call the phone goes black like it was close to my ear. This only happen if I answer the call and if I make a call it happens right away.The phone is still on and the calls go through but the phone goes black and is useless and I can't even hang it up until the other person hangs up. Not even pressing the power button on the top helps. I have checked and nothing is blocking the sensor on the front of the phone and the new digitizer I got from ebay but again it is a perfect fit and nothing is blocking the sensors...Any Ideas or suggestions? anything would be a great help thank you!
Click to expand...
Click to collapse
The sensor that the phone uses in order to register face proximity is just to the left of the forward facing camera. Ensure this is connected nice and solid (reseat the wire if necessary) and make sure there is no dust in it as this will likely cause it to behave as it has. Simply replacing the screen won't do this, but improper cleaning before replacing the screen could. You may have to tear the phone down again just to reseat the screen itself.
ZombieWarez said:
About a couple weeks ago I cracked the digitizer(touch screen) on my Lg Thrill and replaced it. Before doing this everything was fine with the phone...I upgraded to GB and it is also rooted but like I said everything was working just fine until I replaced the digitizer. Now every time I make or receive a phone call the phone goes black like it was close to my ear. This only happen if I answer the call and if I make a call it happens right away.The phone is still on and the calls go through but the phone goes black and is useless and I can't even hang it up until the other person hangs up. Not even pressing the power button on the top helps. I have checked and nothing is blocking the sensor on the front of the phone and the new digitizer I got from ebay but again it is a perfect fit and nothing is blocking the sensors...Any Ideas or suggestions? anything would be a great help thank you!
Click to expand...
Click to collapse
hmm i had the same issue BUT mine would do it when i cracked the digitizer, which is weird.. replacing my digitizer fixed the issue or it just cleared up itself, try resetting the phone.. Or like zombie said, Tear it down and clean the connectors and sensors
Cynagen said:
The sensor that the phone uses in order to register face proximity is just to the left of the forward facing camera. Ensure this is connected nice and solid (reseat the wire if necessary) and make sure there is no dust in it as this will likely cause it to behave as it has. Simply replacing the screen won't do this, but improper cleaning before replacing the screen could. You may have to tear the phone down again just to reseat the screen itself.
Click to expand...
Click to collapse
I have taken the phone completely apart and used a can of compressed air to clean it I double checked the sensor connector and made sure there was no dirt or dust in or around the connections. I put the phone back together and made a test call...still doing the same thing
But I did notice that when I made a second test in a dark room the phone did not go black and when I moved the phone close to a light the phone went black....needless to say I am so confused now more then ever. I did a third test and the same thing happened. So any other ideas as to what may be going on??? Seems like the sensor is working no? just in reverse??? Maybe the tint in the new digitizer is too dark? but this still makes no sense as to why the phone goes black when it gets exposed to light. Anyway any other help would be great right about now THANK YOU!
Hi,
Have not posted in here in a while but i'm having a huge problem with my HTC one M7.
Had the phone for a year now and suffered a problem with it once before. The problem before was something to do with the phone locking itself and required me sending it off to HTC to repair. It kept bootlooping and wouldn't allow me to do anything at all.
This problem hasn't occurred since repair however last week the phone was working fine until the next morning when i woke up. My girlfriend used my phone to send herself some photo's and then put the phone on charge as the battery was running low. When i woke up the screen stays black and wont allow me to do anything. If i hold the power button the bottom two lights flash and i can hear the phone booting itself back up. I have a feeling the phone works since everyday at 6:15pm my alarm goes off and i am able to deactivate the alarm by swiping up (i remember the location of the dismiss function) it would appear i'm also able to receive calls and texts since i can hear my message and ring tone going off however cannot see the screen.
I have tried a few things such as holding buttons to reboot, shining a light onto the sensor during a reboot and fully charging etc however nothing.
I should also add i have a slight hairline crack in the screen which occurred about 9 months ago but didn't appear to affect the LCD at all or the digitiser either. Any help would be highly appreciated or any tips on stuff to try.
more information available if needed.
Many Thanks
Kris
MrWain said:
Hi,
Have not posted in here in a while but i'm having a huge problem with my HTC one M7.
Had the phone for a year now and suffered a problem with it once before. The problem before was something to do with the phone locking itself and required me sending it off to HTC to repair. It kept bootlooping and wouldn't allow me to do anything at all.
This problem hasn't occurred since repair however last week the phone was working fine until the next morning when i woke up. My girlfriend used my phone to send herself some photo's and then put the phone on charge as the battery was running low. When i woke up the screen stays black and wont allow me to do anything. If i hold the power button the bottom two lights flash and i can hear the phone booting itself back up. I have a feeling the phone works since everyday at 6:15pm my alarm goes off and i am able to deactivate the alarm by swiping up (i remember the location of the dismiss function) it would appear i'm also able to receive calls and texts since i can hear my message and ring tone going off however cannot see the screen.
I have tried a few things such as holding buttons to reboot, shining a light onto the sensor during a reboot and fully charging etc however nothing.
I should also add i have a slight hairline crack in the screen which occurred about 9 months ago but didn't appear to affect the LCD at all or the digitiser either. Any help would be highly appreciated or any tips on stuff to try.
more information available if needed.
Many Thanks
Kris
Click to expand...
Click to collapse
It looks like you tried all of the usual methods, sorry but it might just be the screen is shorted.
majmoz said:
It looks like you tried all of the usual methods, sorry but it might just be the screen is shorted.
Click to expand...
Click to collapse
I thought as much, i have ordered a new screen and once its delivered i am gonna attempt to fit it and see what happens, thanks for the reply.
Hello,
I know a lot of us are having problems with displays and digitizers and im wondering if anyone else has this problem. Yesterday i replced my screen because it had a dead zone. I booted up the phone and everything worked great until i locked the screen. When i pressed the power button to unlock it there was just a black screen with lots of white lines forming. Without fail the phone will do this. I restart and its fine but when i lock it, it gets screwy. I really need to get this working since i dont even have a backup phone right now. By the way the display is not oem its a knockoff.
Since you change your LCD....it might be a different panel from your original. Check your kernel or flash the kernel again.
Sent from My LG G2 LS-980 or LG G Pad 7.0 V400
Same thing happen to me about a month ago during my G2 screen repair. I bought mine on ebay from a seller that had sold hundreds of them, figured I couldn't go wrong. Unfortunatly I never figuered out why it was failing and just ended up returning it for a refund. The second screen I bought was from etradesupply and it worked perfectly. Hopefully someone has a fix for this weird issue.
I had that exct thing happen to me, well rainbow colored lines. I shattered the screen on a corner drop. I took it to Gopher Mods, they replaced the screen and within a few minutes it happened. They replaced it 2 more times and eventually the last time the screen popped out a little bit since they did not add enough glue/sticky tape inside and the lines dissapeared. They also gave me a full refund, with which I got another G2. So two working phones now lol.
Basically the screen might be pressed in too tightly causing the cable inside to be kinked too much. Its very easy to damage the video cable in this phone mind you.
Bmatthews11 said:
Hello,
I know a lot of us are having problems with displays and digitizers and im wondering if anyone else has this problem. Yesterday i replced my screen because it had a dead zone. I booted up the phone and everything worked great until i locked the screen. When i pressed the power button to unlock it there was just a black screen with lots of white lines forming. Without fail the phone will do this. I restart and its fine but when i lock it, it gets screwy. I really need to get this working since i dont even have a backup phone right now. By the way the display is not oem its a knockoff.
Click to expand...
Click to collapse
Try installi mg dorimanx's kernel which detects your panel type of search the thread for a kernel swap flashable. Your new panel may be of a different type causing the white lines.