Database Develop

Recovery

Hi ! I have a problem...
With my Honor 5C, i have no recovery, it freeze on boot for the recovery and i tried to flash TWRP but no result...
Can i have a solution for this ?

DaRkLinK_35 said:
Hi ! I have a problem...
With my Honor 5C, i have no recovery, it freeze on boot for the recovery and i tried to flash TWRP but no result...
Can i have a solution for this ?
Click to expand...
Click to collapse
You need to download full firmware for your phone version. Put it on sdnin dload folder then turn off the phone completely. After that volume up and down together (no power button). It should install the whole system again. If I remember correctly all steps :silly:

ConradP said:
You need to download full firmware for your phone version. Put it on sdnin dload folder then turn off the phone completely. After that volume up and down together (no power button). It should install the whole system again. If I remember correctly all steps :silly:
Click to expand...
Click to collapse
Close enough. Actually, you have to press volume up, down AND the power button to install the firmware.
The whole process is the following :
- Use Huawei Firmware Finder to find the correct ROM to install on your device and download it. Be sure to download the correct file corresponding to your firmware/build version. This is VERY important.
- Plug your Honor 5C to your computer and create a dload folder to the root of your internal storage.
- Extract the archive you got from Huawei Firmware Finder and put the update.app file in the dload folder.
- Now put your phone off and back on by pressing simultaneously volume up, down and power button altogether. That should take care of that soft brick of yours and reinstall the whole system.
After that, you should be good to go.

Hi ! Thanks for your reply ConradP and Zarou !
For download the firmware, I have a beta Nougat update, so... How can I find the firmware for update ?
Thanks !

DaRkLinK_35 said:
Hi ! Thanks for your reply ConradP and Zarou !
For download the firmware, I have a beta Nougat update, so... How can I find the firmware for update ?
Thanks !
Click to expand...
Click to collapse
Unfortunately, I don't know about beta update, sorry. Maybe you can download your previous firmware from HFF (the one you had before the beta) and then get back the Nougat update from where you got it in the first place.
By the way, are you sure that Nougat is supported by your device ? Apparently the beta is for some firmware variants only.

Hi !
This link was you redirected to the image for my honor 5C Nougat 7 and.. When how can I find the update for this version ?
Thanks man
http://hpics.li/cb7205f

Original Android firmware for P7-L10

Hey Everyone.
I recently purchased used Huawei P7-L10. Dual Sim Version
There is an issue in it. At the back of the cell its written Model. Huawei P7-L10 FCC ID: QISP7-L10 IC:6369A-P7L10, But when i checked in to the Settings> About Phone there is Model No. Huawei P7-L01, Build No. L01V100R001C17B608 android version 4.4.2 and EMUI wersion is 3.0
Now coming to the known problems.
1- Phone is too slow to operate ( when i press any icon it opens after 1 or 2 seconds).
2-Sound is creating problems.
3-Unable to use 4g LTE while as per my operator it is supported for 4g.
Please Help me out in this regard. I am so so so worry.
and sorry for my bad english please.
thanks in advance.

upgrade your firmware to B853 ( 5.1.1 LOLLIPOP) and your problems will be solved
find thread in general section

Thanx for your reply bro. I have downloaded the requited update.app file. Placed in SD card. Turned off the device. Then kept pressing volume up + volume down and power key for more then 10 seconds but nothing happened.
When I go to recovery and tried to update via SD card. Update.app file is not shown there.
What to do now please help me out.
Thnx in advance.

zaabolla said:
upgrade your firmware to B853 ( 5.1.1 LOLLIPOP) and your problems will be solved
find thread in general section
Click to expand...
Click to collapse
I also tried via dial pad command prompt *#*#2846579#*#* and choose updater and then update SD Card.
In reply it says Please do MT , PT first.
What is this now?

nashi_jee said:
Thanx for your reply bro. I have downloaded the requited update.app file. Placed in SD card. Turned off the device. Then kept pressing volume up + volume down and power key for more then 10 seconds but nothing happened.
When I go to recovery and tried to update via SD card. Update.app file is not shown there.
What to do now please help me out.
Thnx in advance.
Click to expand...
Click to collapse
download full B853 firmware and extract it
make a folder named " dload " in your sd card and put Update.app in it
backup your data first ( photos , contacts ... )
power off your phone and force update to upgrade it

zaabolla said:
download full B853 firmware and extract it
make a folder named " dload " in your sd card and put Update.app in it
backup your data first ( photos , contacts ... )
power off your phone and force update to upgrade it
Click to expand...
Click to collapse
I have tried this method bro but every time it is failed to update via updater app.
And force update is not being started by the phone.
Error msg is as under
Entry SD upgrade...
verify: unknown module - EFI
error: partition verify is failed
update /sdcard/dload/update.app failed
What to do now?

is there any person who can help me out please.

Unlock your bootloader with huawei's site (take any country @register if yours is not in the list)
Use Hawei Firmware Extractor to extract the 4 files needed of a B853 firmware (from carbontesla)
fastboot flash boot boot.img
fastboot flash cust cust.img
fastboot flash system system.img
fastboot flash recovery recovery.img

My huawei p7 L10 emui version 3.0 .I want upgrade it 4.4.2 to 5.0 how I upgrade its I have check upgrade but it no upgrade but other p7 l 10 is upgraded but its not upgraded tell me how iam upgrade it

Kindly support
I m getting option that please do MT, PT First?

AL10 Can't get OTA to work

I have an AL10 with Chinese firmware. I used SRK Tool for Huawei and did the following
1. unlocked booloader
2. install twrp
3. Flash L19C646B190 from twrp
4. root
5. update oeminfo to C636
- After this step I had issues that when I boot the phone kept on asking for a password to decrypt the storage. I booted into twrp and tried to change the /data partition to ext4 from f2fs, but couldn't
6. Tried to flash L19C646B190 using UPDATE.APP and volume up + volume down + power, but couldn't. Phone complained that the firmware was incompatible
7. Used SRK Tool to update ro.build.display.id to EVA-L19C900B00. It was #ro.build.display.id=disabled
8. Flashed L19C646B190 using UPDATE.APP and volume up + volume down + power
9. Bootloader was locked again and twrp replaced with stock recovery after flashing
All in all the phone seems to be working find, but OTA is not working.
How do I go about getting OTA to work again?

za_fluffybunny said:
I have an AL10 with Chinese firmware. I used SRK Tool for Huawei and did the following
1. unlocked booloader
2. install twrp
3. Flash L19C646B190 from twrp
4. root
5. update oeminfo to C636
- After this step I had issues that when I boot the phone kept on asking for a password to decrypt the storage. I booted into twrp and tried to change the /data partition to ext4 from f2fs, but couldn't
6. Tried to flash L19C646B190 using UPDATE.APP and volume up + volume down + power, but couldn't. Phone complained that the firmware was incompatible
7. Used SRK Tool to update ro.build.display.id to EVA-L19C900B00. It was #ro.build.display.id=disabled
8. Flashed L19C646B190 using UPDATE.APP and volume up + volume down + power
9. Bootloader was locked again and twrp replaced with stock recovery after flashing
All in all the phone seems to be working find, but OTA is not working.
How do I go about getting OTA to work again?
Click to expand...
Click to collapse
Try change oeminfo to C432 or C185. I also try to use c636 but never get ota update. My device al00

rhodondendron said:
Try change oeminfo to C432 or C185. I also try to use c636 but never get ota update. My device al00
Click to expand...
Click to collapse
Worked like a charm, thanks I changed my oeminfo to hw / meanaf for c185 and flashed an offical L19C185 from Huawei. Immediately got all the OTAs and the device is working great.
For anybody with an AL10, don't bother looking for a L29 ROM, just Flash n L19, it works perfectly. The OS sees all the RAM and storage space

I flashed L09 rom to my AL-10 and everything is working fine too

I also have an al-10 and I'm tired of the Chinese rom.Can I change it to another rom？

Dirrin said:
I also have an al-10 and I'm tired of the Chinese rom.Can I change it to another rom？
Click to expand...
Click to collapse
Dude! Are you really asking that? OP create this thread because he change his chinesse phone rom to international rom

(Help) My P8 Lite 2017 (PRA-LX1) is bricked

Hello,
I was trying to install a custom ROM from TWRP to my P8 Lite 2017 and I wiped all partitions except MicroSD.
The installation failed and I got the stock ROM and then I discovered that my bootloader is locked. I can access TWRP and when I flashed the stock ROM the phone just boots to TWRP Recovery. And I can't even unlock the bootloader because the phone doesn‘t have any OS and I can‘t enable OEM unlocking from the system settings. And because I have TWRP, I can’t access Huawei Recovery. So my phone is basically bricked.
Any help will be appreciated

luigifan3 said:
Hello,
I was trying to install a custom ROM from TWRP to my P8 Lite 2017 and I wiped all partitions except MicroSD.
The installation failed and I got the stock ROM and then I discovered that my bootloader is locked. I can access TWRP and when I flashed the stock ROM the phone just boots to TWRP Recovery. And I can't even unlock the bootloader because the phone doesn‘t have any OS and I can‘t enable OEM unlocking from the system settings. And because I have TWRP, I can’t access Huawei Recovery. So my phone is basically bricked.
Any help will be appreciated
Click to expand...
Click to collapse
Use dload with a service firmware.
You need to flash this 2 times,once for the firmware and second time for vendor,and the firmware UPDATE.APP can be found in the update_sd.zip and the vendor UPDATE.APP can be found in the PRA-L31 or PRA-L11 folders (most likely you will have PRA-L31,you can find this in the engineering menu by going into the dialer and typing this: *#*#2846579#*#*,and then going to Veneer Informations and Version Info,but since you cannot boot flash PRA-L31 vendor).
http://androidhost.ru/6uc - this is latest firmware,but takes a very very long time to download
https://mega.nz/#F!nwhAWDjC!cNovAN6dKLlO_YZ9fjMbzQ - this is the first official firmware released,but download speed is very good
If you don't know how to use dload you can look it up on forums.

If your phone is really hard bricked and can't do anything, check this out:

I know how to use dload, but how I can boot into dload mode with TWRP installed and bootloader locked?

luigifan3 said:
I know how to use dload, but how I can boot into dload mode with TWRP installed and bootloader locked?
Click to expand...
Click to collapse
Dload works no matter what,at least I was able to enter it when I bricked my phone,even when I completely screwed up my recovery partition,so you should be good. Try using it with the service firmware I left you.

dinoderda said:
Dload works no matter what,at least I was able to enter it when I bricked my phone,even when I completely screwed up my recovery partition,so you should be good. Try using it with the service firmware I left you.
Click to expand...
Click to collapse
Now I have downloaded the service firmware so how I am going to flash it now? Like do I extract the UPDATE.APP and flash it in TWRP or what? You said that flash UPDATE.APP, but am I going to do that in dload mode or TWRP?

luigifan3 said:
Now I have downloaded the service firmware so how I am going to flash it now? Like do I extract the UPDATE.APP and flash it in TWRP or what? You said that flash UPDATE.APP, but am I going to do that in dload mode or TWRP?
Click to expand...
Click to collapse
In dload,make sure you make a folder in the root of your sdcard called dload and put that in there.

dinoderda said:
In dload,make sure you make a folder in the root of your sdcard called dload and put that in there.
Click to expand...
Click to collapse
Now I have the UPDATE.APP in my dload folder, but how I boot to the dload mode now?

luigifan3 said:
Now I have the UPDATE.APP in my dload folder, but how I boot to the dload mode now?
Click to expand...
Click to collapse
Volume Up + Volume Down + Power Button.

dinoderda said:
Volume Up + Volume Down + Power Button.
Click to expand...
Click to collapse
I tried that, it just boots into TWRP
EDIT: I got to dload, but it says software installation failed

luigifan3 said:
I tried that, it just boots into TWRP
EDIT: I got to dload, but it says software installation failed
Click to expand...
Click to collapse
Hm,make sure you used the service firmware I left you,but if you are sure you did,your last resort is DC Phoenix which you will need to pay 20 euros.

luigifan3 said:
Hello,
I was trying to install a custom ROM from TWRP to my P8 Lite 2017 and I wiped all partitions except MicroSD.
The installation failed and I got the stock ROM and then I discovered that my bootloader is locked. I can access TWRP and when I flashed the stock ROM the phone just boots to TWRP Recovery. And I can't even unlock the bootloader because the phone doesn‘t have any OS and I can‘t enable OEM unlocking from the system settings. And because I have TWRP, I can’t access Huawei Recovery. So my phone is basically bricked.
Any help will be appreciated
Click to expand...
Click to collapse
if you have TWRP installed could you make a backup of your oeminfo partition so we could provide you the right firmware to recover your device

RAR1991 said:
if you have TWRP installed could you make a backup of your oeminfo partition so we could provide you the right firmware to recover your device
Click to expand...
Click to collapse
Ok, but does it provide the right info if I have flashed different oeminfo.img?

dinoderda said:
Hm,make sure you used the service firmware I left you,but if you are sure you did,your last resort is DC Phoenix which you will need to pay 20 euros.
Click to expand...
Click to collapse
I've tried a different firmware for my device and now I can't get to dload anymore so does it mean that I've chosen the wrong firmware? And by the way I read somewhere that if the dload says error it can depend on the microsd card.

I tried it again with the service firmware and I got to dload and it didn't have error anymore and now I've got everything worked and my phone is unbricked

luigifan3 said:
I tried it again with the service firmware and I got to dload and it didn't have error anymore and now I've got everything worked and my phone is unbricked
Click to expand...
Click to collapse
great

I was stuck with a similar problem. Device bricked and flashing TWRP and restoring backups, then stock recovery and stock roms, but nothing worked until I found this post. Thanks a lot dinoderda for your help.

dinoderda said:
Use dload with a service firmware.
You need to flash this 2 times,once for the firmware and second time for vendor,and the firmware UPDATE.APP can be found in the update_sd.zip and the vendor UPDATE.APP can be found in the PRA-L31 or PRA-L11 folders (most likely you will have PRA-L31,you can find this in the engineering menu by going into the dialer and typing this: *#*#2846579#*#*,and then going to Veneer Informations and Version Info,but since you cannot boot flash PRA-L31 vendor).
http://androidhost.ru/6uc - this is latest firmware,but takes a very very long time to download
https://mega.nz/#F!nwhAWDjC!cNovAN6dKLlO_YZ9fjMbzQ - this is the first official firmware released,but download speed is very good
If you don't know how to use dload you can look it up on forums.
Click to expand...
Click to collapse
Hello again, I've been using the older service firmware for few months now and now I decided to install the latest service firmware after I had no success with flashing the firmware through TWRP and I downloaded the service firmware put the necessary files to the dload folder and installed it via the software update in the dialer and typing *#*#2846579#*#* and going to dload that way. It installed to 100% and then when it restarted it goes to Error Mode and it says to update the firmware again but it just loops to error mode and I cannot do anything so I think I accidentally removed some neccessary files in the dload folder but now I would need to fix the error mode loop.

[GUIDE] Downgrade from EMUI 9.1 to 8.0 for bootloader unlocking

Hey guys.
I was on EMUI 9.1.0.166(C675) which is the May 2020 security update and I wanted to unlock my bootloader which is only possible if you are on EMUI 8 with a security patch of June 2018 or below. There was no option in HiSuite to downgrade as well. I came across many users not able to find the right firmware to flash for their device. So I made this guide to help them.
These are the details of my device before downgrading
Model Number: LLD-AL10
EMUI Version: 9.1.0.166(C675E6R1P4)
These are the firmware I flashed in order to reach the desired version in order to unlock the bootloader.
1. EMUI 9.1.0.112(C675E4R1P4T8) https://androidhost.ru/1lau
This firmware should be flashed via dload method.
2. After successfully flashing this. You can connect your device to HiSuite and then you'll get an option to switch to EMUI 8.0.
3. Then flash EMUI 8.0.0.194 via dload method again https://androidhost.ru/29Fa
4. Finally flash this firmware version via dload. Click here
P.S You can maybe skip step 3 and directly flash the firmware in Step 4. I don't know if it'll work or not.
After flashing the 4th firmware, your device may bootloop and go to erecovery. This is completely fine. If it goes into erecovery just wipe the data/factory reset and you're good to go!
Hope this will help you guys!

will it work on LLD-L21?

Quackboy said:
will it work on LLD-L21?
Click to expand...
Click to collapse
I don't know but you can try! It's perfectly safe because even if the firmware is not compatible it will just say update failed. Nothing will happen to the device.

Not works on HONOR 9 Lite LLD-L31

I copied firmware files in dload folder and used volume + with volume - with power button. But it says update failed

prashantvrm said:
I copied firmware files in dload folder and used volume + with volume - with power button. But it says update failed
Click to expand...
Click to collapse
The dload folder will already be in the zip file downloaded. Just add it to the root of sd card and update. I didn't use the volume button method, I used the manual software update method by dialing *#*#2846579#*#*

Majid2000 said:
The dload folder will already be in the zip file downloaded. Just add it to the root of sd card and update. I didn't use the volume button method, I used the manual software update method by dialing *#*#2846579#*#*
Click to expand...
Click to collapse
Hi, Instructions are not clear. Can you please provide excat directory to save the files on memory card?
I have tried placing the zip file on memory card. It says 'No upgrade file'. I've extracted and placed the dload folder in memory card. Then it says 'update failed'. No matter how hard I try, I'm not able to apply the update on step 1.

Hello. I have been following your guide on unlocking honor 9 lite bootloader. I reached till step 3 successfully. The firmware in step 4 (google drive link) is missing. I want to unlock my honor 9 lite and your guide seems to be quite helpful! Hope you will correct the drive link. Thankyou!

Hey majid, can you tell me which file do i need to copy to the root directory of the sd card as there are many folders in the dload folder in the rom you provided.
I am confused.
1. As i extracted the zip there are 1 folders namely release doc and software
2. In software there is dload folder and in that there are other 2 folders namely LLD L22A and LLD L22C and an update zip...
What is the next step .. kindly reply.

Hello, anyone have the 4. link (google drive link is down) ?
Thanks