First u have to understand what is brick
Two terms are therr softbrick and hardbrick
And many noobs use them interchangeably without having proper knowledge
So softbrick means a situations where ur rom is not working or bootloop kind of thing
And hardbrick means ur device is fully dead with no recovery no fastboot nothing blank screen
My device was recently hardbricked or dead with no fastboot no recovery nothing and it was the first time i experienced a brick so after searching a lot i could not find a guide specific to ze550kl and i lost hopes
Then i visisted local service centre they said motherboard gone
I was ?
Then i visited local shops they said they dont repair asus
I was sure that device can be unbricked so i again started googling
And i find a post where one person said some great words that
SNAPDRAGONS ARE UNBRICKABLE lol
It boosted my spirit and then i luckily i find a firmware called raw firmware which contains all files to unbrick my phone
Now the real steps i followed
Firstly u should analyze ur device
For this
Download all files from the link below
And install qpst drivers
Then qpst software
And then take the battery out put it again connect ur phone to pc
Ur pc should detect something like
Qcom 9008 port in device manager
If it does then ur on the top of world
Now open qfil software
Check ur device got detected
Then select programmer file browse to folder name firmware ( in the zip i provided below )
select file
And then select xml
And then click on download content
When it completes
Disconnect device remove battery and insert and power on
Ur phone should be in fastboot mode
Vooohooo
From coma to live
Now u have two options either to flash twrp using fastboot and restore ur backup
Or download the full rom below and unzip and click on fastboot flashall.bat
It will flash whole firmware
Only unbrick files - https://drive.google.com/file/d/0B8O22xDxCq2FTDlyV2ZiNDZxaUU/view?usp=drivesdk
emmcfile -https://drive.google.com/file/d/0B8O22xDxCq2FUHhZbV8yYl84Ulk/view?usp=drivesdk
Put this file in firmware folder i forgot to add this before
Full firmware - https://drive.google.com/file/d/0B43Ue6xY9MmdOGxXZ2RRQUJrOWs/view?usp=sharing
All devices firmware - https://firmware27.blogspot.in/2014/12/file-raw-asus-zenfone.html?m=1
emmc raw dump - http://www.mtkdeveloper.com/2016/12/file-dump-asus-zenfone.html?m=1
Thanks to @okmikel for the link
Thank you
Hit thanks if it helped you
I wrote this guide in short time i will elaborate more in few days
If u r stuck somewhere u can contact me at
Telegram. @ady692
Or pm me at xda
I was doing everything as per your instruction but something is going wrong.In QFIL I believe the button I have to click is 'Download' After loading the XML files cause 'Download Content' button just prompts me to select another file.
Even after clicking Download just below the 'Load XML' button the dialog says this:
"Sahara Version:0
Start Sending Programmer
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
at QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(String sFileName)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download"
what should I do!!I need help.
Jitesh saha said:
I was doing everything as per your instruction but something is going wrong.In QFIL I believe the button I have to click is 'Download' After loading the XML files cause 'Download Content' button just prompts me to select another file.
Even after clicking Download just below the 'Load XML' button the dialog says this:
"Sahara Version:0
Start Sending Programmer
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
at QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(String sFileName)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download"
what should I do!!I need help.
Click to expand...
Click to collapse
what is ur phone model?
And in qfil
U have to select 3 files
First is
Programmer file
Raw xml
Patch file
The files given by me are for ze550kl snapdragon 410 chipset
Make sure ur phone is detected by qfil
As 9008 download mode
addy692 said:
what is ur phone model?
And in qfil
U have to select 3 files
First is
Programmer file
Raw xml
Patch file
The files given by me are for ze550kl snapdragon 410 chipset
Make sure ur phone is detected by qfil
As 9008 download mode
Click to expand...
Click to collapse
it is 550KL with 410 processor heres a screenshot of ehat I see
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Jitesh saha said:
it is 550KL with 410 processor heres a screenshot of ehat I see
Click to expand...
Click to collapse
then it should work
Try again
Remove phone battery and insert and then try
Restart pc
Then try
And when u stuck please tell
How u bricked and wats the state if ur device now
Coz unbrick process depends upon situations
addy692 said:
First u have to understand what is brick
Two terms are therr softbrick and hardbrick
And many noobs use them interchangeably without having proper knowledge
So softbrick means a situations where ur rom is not working or bootloop kind of thing
And hardbrick means ur device is fully dead with no recovery no fastboot nothing blank screen
My device was recently hardbricked or dead with no fastboot no recovery nothing and it was the first time i experienced a brick so after searching a lot i could not find a guide specific to ze550kl and i lost hopes
Then i visisted local service centre they said motherboard gone
I was ?
Then i visited local shops they said they dont repair asus
I was sure that device can be unbricked so i again started googling
And i find a post where one person said some great words that
SNAPDRAGONS ARE UNBRICKABLE lol
It boosted my spirit and then i luckily i find a firmware called raw firmware which contains all files to unbrick my phone
Now the real steps i followed
Firstly u should analyze ur device
For this
Download all files from the link below
And install qpst drivers
Then qpst software
And then take the battery out put it again connect ur phone to pc
Ur pc should detect something like
Qcom 9008 port in device manager
If it does then ur on the top of world
Now open qfil software
Check ur device got detected
Then select programmer file browse to folder name firmware ( in the zip i provided below )
select file
And then select xml
And then click on download content
When it completes
Disconnect device remove battery and insert and power on
Ur phone should be in fastboot mode
Vooohooo
From coma to live
Now u have two options either to flash twrp using fastboot and restore ur backup
Or download the full rom below and unzip and click on fastboot flashall.bat
It will flash whole firmware
Only unbrick files - https://drive.google.com/file/d/0B8O22xDxCq2FTDlyV2ZiNDZxaUU/view?usp=drivesdk
emmcfile -https://drive.google.com/file/d/0B8O22xDxCq2FUHhZbV8yYl84Ulk/view?usp=drivesdk
Put this file in firmware folder i forgot to add this before
Full firmware - https://drive.google.com/file/d/0B43Ue6xY9MmdOGxXZ2RRQUJrOWs/view?usp=sharing
All devices firmware - https://firmware27.blogspot.in/2014/12/file-raw-asus-zenfone.html?m=1
emmc raw dump - http://www.mtkdeveloper.com/2016/12/file-dump-asus-zenfone.html?m=1
Thanks to @okmikel for the link
Thank you
Hit thanks if it helped you
I wrote this guide in short time i will elaborate more in few days
If u r stuck somewhere u can contact me at
Telegram. @ady692
Or pm me at xda
Click to expand...
Click to collapse
I did everything now phone boots Into fastboot only. Can't access the recovery and I get the error message every time "partition table doesn't exist". How to resolve this. Ze550kl hard bricked.
Sent from my SM-G920F using Tapatalk
karthikeyan346 said:
I did everything now phone boots Into fastboot only. Can't access the recovery and I get the error message every time "partition table doesn't exist". How to resolve this. Ze550kl hard bricked.
Click to expand...
Click to collapse
Have u downloaded the full firmware above
??
help me find qfil file for asus Z00ed....:crying::crying::crying:
kaveemung said:
help me find qfil file for asus Z00ed....:crying::crying::crying:
Click to expand...
Click to collapse
Why crying
Take this
https://drive.google.com/uc?id=0B43Ue6xY9MmdN2pDWmVQbHdhSEE&export=download
i havent start the qfil process, i want programmer file,patchfile xml and raw programme xml file, for Z00ED ze500kl I cant bring my phone to fastboot mode
kaveemung said:
i havent start the qfil process, i want programmer file,patchfile xml and raw programme xml file, for Z00ED ze500kl I cant bring my phone to fastboot mode
Click to expand...
Click to collapse
All these files are in the raw firmware zip
Download whole zip
U will get files in the firmware folder
Or u can try using unbrick files zip in the op
Coz these files are chipset dependent i think
addy692 said:
All these files are in the raw firmware zip
Download whole zip
U will get files in the firmware folder
Or u can try using unbrick files zip in the op
Coz these files are chipset dependent i think
Click to expand...
Click to collapse
I don't get your point..what do u mean by "try using unbrick file zip in op"
please tell me how to do it
Good work friend
Its like Oxygen cap support for mobile.
Keep it up.
Sharing is caring
kaveemung said:
I don't get your point..what do u mean by "try using unbrick file zip in op"
please tell me how to do it
Click to expand...
Click to collapse
Just download ur phones raw firmware all files are there for qfil
RonakRonak said:
Good work friend
Its like Oxygen cap support for mobile.
Keep it up.
Sharing is caring
Click to expand...
Click to collapse
Yup
Its a basic beed for testors and developers
addy692 said:
Just download ur phones raw firmware all files are there for qfil
Click to expand...
Click to collapse
I have downloaded around 5 raw firmware spend around 10gb but didn't find the required file sir
,
op is the first time I have heard about, please guide me the process
kaveemung said:
I have downloaded around 5 raw firmware spend around 10gb but didn't find the required file sir
,
op is the first time I have heard about, please guide me the process
Click to expand...
Click to collapse
Dnld this
https://drive.google.com/uc?id=0B43Ue6xY9MmdN2pDWmVQbHdhSEE&export=download
And u havnt described what u want to do with these files
Is yr fone hardbricked ?
addy692 said:
Dnld this
https://drive.google.com/uc?id=0B43Ue6xY9MmdN2pDWmVQbHdhSEE&export=download
And u havnt described what u want to do with these files
Is yr fone hardbricked ?
Click to expand...
Click to collapse
my phone is hard bricked, no bootloop, phone dead, cant switch on,only laptop can detect in usb qualcomm 9008 mode..i have acidentally wipe/formatted my internal sd card(system)
so i need rawprograme0.xml and patch0.xml, prog_emmc_firehose_8916.mbn file for QFILE FLASH, i havent found any of the file in downloaded raw firmware file
kaveemung said:
my phone is hard bricked, no bootloop, phone dead, cant switch on,only laptop can detect in usb qualcomm 9008 mode..i have acidentally wipe/formatted my internal sd card(system)
Click to expand...
Click to collapse
Then dnld the above firmware and flash
Wats the prob
addy692 said:
Then dnld the above firmware and flash
Wats the prob
Click to expand...
Click to collapse
i cant not find any of the 3 required file from the raw firmware downloaded viz prog_emmc_firehose_8916.mbn, rawprogram0.xml, patch0.xml for QFIL FLASH, when flahing with QFIL FLASH error, sahara file fail
:crying::crying::crying:
Related
Flashing stock ROM on LG L Fino
Since the device is pretty new and there is no other such guide for the Fino I decided to make one.
Flashing stock firmware on LG devices is universal (for the most part) so this guide will be pretty straight up.
This guide should be compatible with both the Dual Sim Fino and the regular one and all variants between them N/F/G etc.
I will try to make this as noob friendly as possible.
Click to expand...
Click to collapse
__________________
Flashing a stock ROM:
Can unbrick the device (only if softbricked)
Will remove root
Can Wipe user data
Can brick device (If done incorrectly)
__________________
STEPS:
STEP 1: Download and Install the LG DRIVER from here.
You might want to restart your computer after driver installation.
STEP 2: Download LG FLASH TOOL 2014 from here and extract it IN a NEW folder somewhere.
STEP 3: Download a KDZ firmware file from here
BE SURE YOU ARE DOWNLOADING THE RIGHT FIRMWARE FOR YOUR DEVICE (D290N, D295 and so on) OTHERWISE YOUR DEVICE MIGHT BECOME A HARD BRICK!!! LOOK FOR THE DEVICE MODEL BEHIND THE BATTERY!
Click to expand...
Click to collapse
STEP 4: Extract the FIRMWARE.KDZ file IN the same folder as the LG FLASHTOOL 2014.
STEP 5: Enter DOWNLOAD MODE on the device. You can do that by connecting a USB cable to the computer and then pressing and holding the VOLUME UP button while inserting the USB in to the phone.
STEP 6: Start LGFlashTool2014.exe. You should have something like this open:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
STEP 7: In type ALLWAYS choose CDMA.
STEP 8: IN KDZ browse to the KDZ file you extracted earlier and select it.
STEP 9: Select Normal or CSE Flash
Normal Flash: Flash the ROM on top of the current one ( Good for updating firmware)
CSE Flash: Flash the ROM after WIPING EVERYTHING. (Good if testing new ROM or restoring a brick)
Click to expand...
Click to collapse
STEP 10: After selecting either you will be transferred to another screen with data on it. Don't edit anything and just click START
STEP 11: After that you will be yet again transferred to another screen like this:
Dont change or tick anything and just click OK
STEO 12: After that the process of FLASHING will begin.
THIS PROCESS CAN'T BE STOPPED SO BE SURE YOU HAVE EVERYTHING NEEDED TO WAIT FOR 5-20 MINUTES FOR IT TO COMPLETE.
DO NOT UNPLUG THE DEVICE UNTIL IT HAS FULLY BOOTED!
Click to expand...
Click to collapse
If you get an error saying something about failed downloads and whatnot DO NOT CLICK ON ANYTHING! and wait about 15 minutes. The program might just display these errors but the process will continue.
Do not worry if the program says disconnected or crashes at the end of the procedure. This is normal
STEP 13: Enjoy your reflashed device
__________________
By following this guide you agree that I TAKE NO RESPONSIBILITY FOR BRICKED OR DAMAGED DEVICES.
You and only you decided to follow these instructions.
Click to expand...
Click to collapse
Download the KDZ you need here: https://lg-firmwares.com/
johnwilliam_a_k_a_trash said:
Nice tutorial!
Click to expand...
Click to collapse
Thanks
Glad to help.
Does anyone experimented issues installing drivers? I've installed several versions and it still not detecting/recognizing the device and searching for drivers in windows update. (Windows7, D290n).
---------- Post added at 12:36 PM ---------- Previous post was at 12:05 PM ----------
carmeloamg said:
Does anyone experimented issues installing drivers? I've installed several versions and it still not detecting/recognizing the device and searching for drivers in windows update. (Windows7, D290n).
Click to expand...
Click to collapse
SOLVED: After disabling windows update, uninstalling every single driver version for the device, unplugging network connection and reinstalling drivers (4.0.3) it worked. Thanks and hope help if it is your case.
Ok so i tried to flash kdz file but on 60% it say "The phone is disconnected from PC" What should i do?
cyber808 said:
Ok so i tried to flash kdz file but on 60% it say "The phone is disconnected from PC" What should i do?
Click to expand...
Click to collapse
You can start over... But this time check that the USB connection is stable and the drivers are all updated
Lg l fino hardbricked!
Hi! i'm a newbie here, can you teach me to unbrick a hardbricked lg l fino? no download mode and it says boot security error, it has been days solving this problem ...
micoevil said:
Hi! i'm a newbie here, can you teach me to unbrick a hardbricked lg l fino? no download mode and it says boot security error, it has been days solving this problem ...
Click to expand...
Click to collapse
Deppends if it really is hard bricked. Can you enter download mode?
meganukebmp said:
STEP 5: Enter DOWNLOAD MODE on the device. You can do that by connecting a USB cable to the computer and then pressing and holding the VOLUME DOWN button while inserting the USB in to the phone.
__________________
Click to expand...
Click to collapse
I have LG L Fino D295. I cannot enter to Download Mode as there is error message "error boot certification verify" and then the device goes black. By removing the battery, put it back and press power button the phone goes normally. Any solution for cannot entering the Download Mode?
I found this thread: http://forum.xda-developers.com/showthread.php?t=2582142 but I couldn't find the files needed (sbl1.img, aboot.img, rpm.img, tz.img) which I assume the stock files for LG Fino L D295. And not really sure this will help me to enter the Download Mode.
Just as background: when I update the firmware via OTA, the system says that my phone is suspected to be rooted. since then my camera is not working. Clear cache and data didn't help.
Any suggestion would be appreciated.
thenks bro
Hello, I have a problem because after installing TWRP on Lg l'fino from time changed the android I changed not at all aboot on orginale and call me zbrickował
I wanted to install in new home Stock for lg flash tool because tele enters into download mode but as it starts to upload new stock becomes 2% percent and pops it failed Tele. 100% charged and detectable packages for Windows
Could anyone help ?? Thanks in advance: D
My English is poor
rohanekpl said:
Hello, I have a problem because after installing TWRP on Lg l'fino from time changed the android I changed not at all aboot on orginale and call me zbrickował
I wanted to install in new home Stock for lg flash tool because tele enters into download mode but as it starts to upload new stock becomes 2% percent and pops it failed Tele. 100% charged and detectable packages for Windows
Could anyone help ?? Thanks in advance: D
My English is poor
Click to expand...
Click to collapse
Try reinstalling LG driver and try plugging in another USB port on your PC.
So I tried to do some driver version I installed, each USB port podłanczałem and all the time is this problrm on your computer is at 2% and continue on your 0% and nothing happens, I wanted to also add that when I turn on the tele. normally it shows the logo lg and the phone vibrates at some time after 2 times,Lg phone detects a mobile phone but the phone installs the first time you connect it does not want to load up to the end,
maybe this is the problem that you have Windows 10 ?? Maybe it is going to change a recovery program ?? and not by the emulator
---------- Post added at 02:49 PM ---------- Previous post was at 02:27 PM ----------
proudlytm said:
Try reinstalling LG driver and try plugging in another USB port on your PC.
Click to expand...
Click to collapse
So I tried to do some driver version I installed, each USB port podłanczałem and all the time is this problrm on your computer is at 2% and continue on your 0% and nothing happens, I wanted to also add that when I turn on the tele. normally it shows the logo lg and the phone vibrates at some time after 2 times,Lg phone detects a mobile phone but the phone installs the first time you connect it does not want to load up to the end,
maybe this is the problem that you have Windows 10 ?? Maybe it is going to change a recovery program ?? and not by the emulator
I flashed my d290g with a d295 firmware to install a rom on it. Now I'm trying to flash the original firmware with the flash tool but I can't manage to flash it, I've tried adding the d290 unlocked bootloader but it's still not flashing. Is there anyway to force the flash tool to install the firmware without checking the model of it or to make a flasheable zip for TWRP with the d290g firmware?
LG L Fino Hard Bricked
Hi. Sorry for me english.
I have LG L Fino (D290N) and me phone hard bricked. when I instal TWPR with aboot.img and rashr application me phone reboot and I have purple screen with DBI Apps Watchdog Reset or black screen all time. No have logo LG, only black screen. No have download mode, recovery mode, fastboot mode. Cant reperair with LG Support tool because have error with me baterry not full charging.
What I must doo to unbricked my phone ? Please help me
To everyone that has hard bricked their phone:
There is no fix of hard bricked LG L Fino we are aware of as of now!
The only way out is to give your phone to warranty service and get it replaced or get its motherboard replaced!
Please, note that you should be very careful when typing these two commands, installing aboot and recovery!
You are doing this at your own risk!
D290 firmware link dead.. File not found... Please post another mirror link.. I need this firmware urgent.... D290
Abdul.wahid9001 said:
D290 firmware link dead.. File not found... Please post another mirror link.. I need this firmware urgent.... D290
Click to expand...
Click to collapse
Links are not dead. Just download for another region.
i can'tf find custom ROM for this device. How did you found?
Hiparci said:
i can'tf find custom ROM for this device. How did you found?
Click to expand...
Click to collapse
Me and my friends made it.
Hello Everyone,
This is Hamza. I have H811 with v20o. I mistakenly flashed the Modem+Boot+Bootloader+Rom of V20i on my device and hard bricked it. My device was totally dead. No Charging/Notification light, No Download Mode, No Boot & No Recovery.
I spent more than 2 days in finding the solution and finally i found it.
Thread by By leptdre, was very helpful for me. But to make it simple the steps to complete unbricking are as follows:
Tools Required:
1. Card Reader+Data Cable
2. A SD Card - 32 GB or 64 GB. I used 64 GB
3. SD Card Formatter - Download Here - Link Updated
4. Win32DiskImager - Download Here - Link Updated
5. Original KDZ - Download Here
6. SystemImage Bin File - Download Here - Link Updated
7. LGUP Tool - Download Here
Steps to Unbrick:
1. Insert your memory card in Card Reader and Format it using Windows Format. While formatting "uncheck Quick Format" and Change Type to "exFat". You can alternatively use SD Card Formatter but make sure that the card is in exFat format.
2. Once format is completed, install Win32DiskImager and open it. Add SystemImage.bin file. If it does not show the bin file just rename SystemImage.bin to SystemImage.img and then select it. Select your memory card and Click Write.
(You can alternatively change the file types on the win32diskimage from .img to all types)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3. One the Write Completes. Eject Card and insert in your LG G4 H811. Press Volume Up Button while connecting the USB Cable.
4. There you go, it will open the download mode. Now Open LGUP Tool as admin. It will show the device as connected. Select the Original KDZ Firmware and Click Start. it will complete and your Mobile will reboot.
5. Now its Done. Enjoy!
Note: I tried it on my H811 and cannot confirm whether it will work on your device or other variant. I am just sharing to help others.
It says you need the decryption key for the bin file download? Also you dont have to change the file ext, just change the file types on the win32diskimage from .img to all types.
I'd love for this to work, but no luck. I'm helping out a friend that was running xTreme. I think TMO forced the update before we could block it again. Now I can't boot to alter the Build.prop to use LGUP.
RodneyMcKay said:
I'd love for this to work, but no luck. I'm helping out a friend that was running xTreme. I think TMO forced the update before we could block it again. Now I can't boot to alter the Build.prop to use LGUP.
Click to expand...
Click to collapse
But can your phone still boot up to download mode?
greedness said:
But can your phone still boot up to download mode?
Click to expand...
Click to collapse
Yes, I can boot to download mode, but LGUP says unknown model. I'd rather not wipe the device if I don't have to.
RodneyMcKay said:
Yes, I can boot to download mode, but LGUP says unknown model. I'd rather not wipe the device if I don't have to.
Click to expand...
Click to collapse
Then this guide is not for you. This guide is for those that was hard bricked and wont turn on at all (aka qualcomm 9001). Basically, the main internal memory is corrupted so it wont turn on the phone. What this guide does is that it makes your phone run from the external mmc, so you could go into download mode just long enough to put in a working kdz. In your case, it's just as good as doing a factory reset.
greedness said:
Then this guide is not for you. This guide is for those that was hard bricked and wont turn on at all (aka qualcomm 9001). Basically, the main internal memory is corrupted so it wont turn on the phone. What this guide does is that it makes your phone run from the external mmc, so you could go into download mode just long enough to put in a working kdz. In your case, it's just as good as doing a factory reset.
Click to expand...
Click to collapse
OK, I misinterpreted the steps. I was assuming that it would boot from ext by default with this process and bypass the internal. I guess it's only a fall back after internal boot failure.
Please download the password
Plz share Decryption key for mega.com image file
Hi, thanks for the help, my model is the h818p, other files needed or with those who are in the first post will work, thank you for your help in advanc
Very Sorry for the inconvenience in Links. I am new on Mega and does not know it well. I have updated the links in original post. If any problem, let me know!
I need help please.
I have a H811 T-mobile LG G4. I unlocked the bootloader, flashed TWRP, flashed MM-20e Global rom which is ported rom from H815 20e. Everything worked well untill I deciced to relock the bootloader! I have issued a command fastboot oem lock and the device began to bootloop. "Secure Booting Error, Error Code 1003, MODIFIED".
I Have tried LG Bridge but it says "Can't check internal storage".
I Have tried LGUP with several kdz files including H81120o but it says "Invalid kdz file"
I have tried LG Flash tool and nothing works.
Your help would be highly appreciated.
What does it shows when you connect your mobile with LPUP tool?
Does it shows h81120o?
If yes then you can install h81120o kdz
LGUP is showing: H81520e
and that's why I'm kind of confused. My device is actually H811 but I have rooted and flashed twrp after and flashed MM H81520e Global ported rom (to get rid of tmobile apps). Everything was working perfectly until I fastboot oem relock -ed it.
I tried H81520e kdz also but same error occurs. "Invalid kdz file".
Is there any way I can get into recovery? or is it possible to flash stock recovery from "download mode" ?
mikatechs said:
LGUP is showing: H81520e
and that's why I'm kind of confused. My device is actually H811 but I have rooted and flashed twrp after and flashed MM H81520e Global ported rom (to get rid of tmobile apps). Everything was working perfectly until I fastboot oem relock -ed it.
I tried H81520e kdz also but same error occurs. "Invalid kdz file".
Is there any way I can get into recovery? or is it possible to flash stock recovery from "download mode" ?
Click to expand...
Click to collapse
You can actually work that out through Download Mode.
Enter Download Mode, Install TWRP through ADB. Once its installed, you will be able to install the flashable stock rom for H811 . I think that would work!
Also have you tried LG Flash Tool?
Note: Make sure to download the right version for H811 (v20i or v20o) and installing the wrong one will hardbrick your device.
I have done everything according to OP. My phone now boots a custom ROM I flashed through TWRP and all is working well as long as I keep SD card in phone. I am stuck from there because I can't flash stock 20i kdz. I get to 9% and it gives error and reboots the phone. Can someone helpbme out? Thanks
divine1250 said:
I have done everything according to OP. My phone now boots a custom ROM I flashed through TWRP and all is working well as long as I keep SD card in phone. I am stuck from there because I can't flash stock 20i kdz. I get to 9% and it gives error and reboots the phone. Can someone helpbme out? Thanks
Click to expand...
Click to collapse
Are you downgrading from v20o to v20i?
I've had no luck with this method. Could it be because I am not using a card reader but instead thru another phone's sd slot?
eshtak12 said:
I've had no luck with this method. Could it be because I am not using a card reader but instead thru another phone's sd slot?
Click to expand...
Click to collapse
I think that is the problem. Did you formatted as per mentioned instructions?
jam1445 said:
I think that is the problem. Did you formatted as per mentioned instructions?
Click to expand...
Click to collapse
Yes, there is an option in My Computer that allows me to get in the sd card( F: ) and not the phone storage itself which is ( H: ). I formatted it as instructed using ( F: ). I'm thinking about purchasing a micro sd to sd adaptor and attempt it again.
In Device Manager I get "Relink hs-usb qdloader 9008" Instead of Qualcomm. Maybe that's another issue?
[GUIDE] Unbrick Tool for OnePlus 5 with OOS 9.0.9 & OOS 9.0.11 (Untouched full stock)
Hello Everyone !!
=>A hard bricked OP5 has nothing but a black screen (nothing ever comes on the screen, not even a boot logo), it might vibrate when a power button is pressed and held for 20 seconds, has no Recovery partition, no adb mode, and no fastboot partition (It might be a flickering OnePlus logo). The device might be detected in Linux and you might be able to even send commands to it. In Windows, the bricked OP5 should be detected as QHUSB_BULK,Unknown Device,Qualcomm something. You might have a bricked OP5 as a result of flashing a kernel meant for a different device (or a ROM meant for another device that included a kernel), tinkering with the boot logo or bootloader, or your attempt of unlocking the bootloader resulted in corrupting the boot partition. Most of the times, it is needed because OEM Unlocking is disabled, and phone can't boot and no recovery.
=>The solution for OP5 hardbrick is similar to OP3,OP3T- you just need a Qualcomm driver and a recovery package.it'll help to get out from one of the most weird state of the phone.(file is exact file from OnePlus)
METHOD
This method is easy to use and flashes OxygenOS 5.1.7 and OxygenOS 9.0.9 on your phone. It wipes all your data and restores all partitions to stock. It will work in any condition unless it is a hardware damage.
Step 1 :- DOWNLOADS :-
OOS 9.0.9: https://mega.nz/file/O4dGFI4b#mbqq8VqUiPwoN85ajTV-H2pDNccD58-ccejQnTQHIBE
OOS 9.0.11:https://mega.nz/file/ekUURaII#FPoezmYL1hPJUkb2Hf90ZqW07iEaCza6etnTPSKJOos
Step 2 :- Extract Drivers and Recovery Tool files on Desktop.
Step 3 :- If you are using Windows other than Windows XP,turn off Driver Signature Enforcement.To do so,follow this guide :- http://www.howtogeek.com/167723/how-...igned-drivers/
Step 4 :- Press the power button for 40 seconds to turn off the phone.
Step 5 :- Press only volume up button for 10 seconds and while keeping it pressed,connect your phone to PC.Keep volume up pressed till your device shows in device manager as [Unknown Device,QHUSB_BULK (under Unknown Devices) or Qualcomm HS USB ...... (under COMs and Ports)].
Step 6 :- Right Click on your device in the device manager and select Update Device Software. Choose the .inf file manually from x86 or x64 folder as the case implies and select Qualcomm 9008 from the listed devices.If you are unable to see 9008,see the end of post for various other methods to show Qualcomm 9008.
Step 7 :- When the device shows as Qualcomm 9008 ,go to the extracted Recovery Package and run the MSM Download Tool as administrator.
Step 8 :- Click start at top left corner and wait for it to finish (green text will come).
Step 9 :- Disconnect phone from PC and boot into system.
How to Make the device show as Qualcomm 9008
1.) Make sure driver signature enforcement is disabled.
2.) Try these drivers,one of them might work too :-
https://www.androidfilehost.com/?fid=24052804347799753
https://www.androidfilehost.com/?fid=24269982086990168
https://www.androidfilehost.com/?fid=24349802275800175
https://www.androidfilehost.com/?fid=24349802275800173
https://www.androidfilehost.com/?fid=24349802275800171
3.)Download this :- http://www.mediafire.com/file/4aqwyi3g1d6wc67/Qualcomm+1.00.11.rar
Keep phone disconnected from PC.
Open the folder "qc" and install the Test Certificate in the following Stores: Trusted Root, Trusted Publisher, Third-Party Root and Personal
Run the Qualcomm setup wizard (also located in the qc folder)
When completed, restart your PC again with Driver Signature Disabled. (Optional but preferred)
The driver should now automatically install. If not, go to device manager and right click "Unknown Device" and click "Update Driver" Search up the QC folder and press ok. The driver should now install.
P.S.: I found the fix for bootloader menu which was changing after flashing through this tool. Just flash the zip in the recovery from the link below after flashing the rom through this tool, and you are good to go.
Please boot your device, set it up then go back to recovery and flash this file.
https://mega.nz/file/n10kkKCQ#LmCm_TDDyZ9cdZPf2pk0mSSV1bgvZflENQG0ubl15SY
NOTE: When the tool gives the "Sahara error", DON'T DISCONNECT THE PHONE from your PC, and press vol up and power button. It maybe seem stupid as a fix but generally it works.
IMP NOTE: There is a quick update, recently I also got stuck at param processing while flashing my device. So uploading the tool which works well. Here is the link. https://mega.nz/file/C1Nw3Cyb#znHfATPuRN4rAy1ZnDO4kMcftEkQ1P6enGxRGSiBh2E
IMP NOTE: There is a quick update, the tool is updated with latest TREBLE OS.
CREDITS @vasu97 - for helping and motivating me to create this thread
@Mar-cel - for bootloader fix zip
Click thanks IF i helped you
Where did you get this file, after I restored it, the bootblock unlock menu changed, is that normal?
Yes it is normal, mine also changed. May be they changed something in latest tool
Hi! First of all, thx for this post. I am getting Error 258 when i execute the tool. I am getting " Qualcomm HS-USB QDLoader 9008" in device manager, is that right? When i'm executing the program, he begins to download cache.img, and then stop and shows me this error :T Gonna send some pics to better ilustrate it.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Can you help me? Thx again.
EDIT: I forgot to mention that my cellphone turns on the led, in color green, when the tool starts to running.
cidsantiago said:
Hi! First of all, thx for this post. I am getting Error 258 when i execute the tool. I am getting " Qualcomm HS-USB QDLoader 9008" in device manager, is that right? When i'm executing the program, he begins to download cache.img, and then stop and shows me this error :T Gonna send some pics to better ilustrate it.
Can you help me? Thx again.
EDIT: I forgot to mention that my cellphone turns on the led, in color green, when the tool starts to running.
Click to expand...
Click to collapse
hv u tried running this tool as administrator abd ur fone shud not turn on any of the led while flashing.. if u r on twrp try format data .. and then try flashing it thru tool.. or may be its bad download at ur side. redownload again.. and try
cidsantiago said:
Hi! First of all, thx for this post. I am getting Error 258 when i execute the tool. I am getting " Qualcomm HS-USB QDLoader 9008" in device manager, is that right? When i'm executing the program, he begins to download cache.img, and then stop and shows me this error :T Gonna send some pics to better ilustrate it.
View attachment 4445915
View attachment 4445916
Can you help me? Thx again.
EDIT: I forgot to mention that my cellphone turns on the led, in color green, when the tool starts to running.
Click to expand...
Click to collapse
Don't worry about green led light while flashing with tool its normal behavior, and about error...maybe because of bad download for sure,try attaching your phone again or check the drivers again...and look at the firs comment - seems like tool is working fine.
djnim said:
hv u tried running this tool as administrator abd ur fone shud not turn on any of the led while flashing.. if u r on twrp try format data .. and then try flashing it thru tool.. or may be its bad download at ur side. redownload again.. and try
Click to expand...
Click to collapse
Yes, i ran it as administrator. M phone was totally bricked, i only got signal in him when i connected at the PC. But i always had this error :T I downloaded it at least 5 times, and got always the same results.
vasu97 said:
Don't worry about green led light while flashing with tool its normal behavior, and about error...maybe because of bad download for sure,try attaching your phone again or check the drivers again...and look at the firs comment - seems like tool is working fine.
Click to expand...
Click to collapse
I did it all, believe me. Reinstalled the drivers multiples times, differents PCS, differents USB ports... I think it was a hardware problem.
I already sent my phone to RMA, so i think it was solved, one way or another But thanks for your replies
cidsantiago said:
Yes, i ran it as administrator. M phone was totally bricked, i only got signal in him when i connected at the PC. But i always had this error :T I downloaded it at least 5 times, and got always the same results.
I did it all, believe me. Reinstalled the drivers multiples times, differents PCS, differents USB ports... I think it was a hardware problem.
I already sent my phone to RMA, so i think it was solved, one way or another But thanks for your replies
Click to expand...
Click to collapse
ohh.. i got tensed as it is my very first thread .
best method to return sotck complete
Thanks for the clear instructions, you have just saved my phone
Dude, thanks for the guide. But kindly check your links in the post. Some are dead ( especially : the mediafire link you gave at last )
Hi
Thank you so much !
AnDrOiDnEoV said:
Dude, thanks for the guide. But kindly check your links in the post. Some are dead ( especially : the mediafire link you gave at last )
Click to expand...
Click to collapse
That's correct. The right link is this: http://www.mediafire.com/file/4aqwyi3g1d6wc67/Qualcomm+1.00.11.rar
Hi, thanks for making this guide with such clear instructions!
I've done every step according to the guide, but I keep facing this issue:
Just to clarify I did run it as administrator.
Are you going to update (5.1.2)?
esedix02 said:
Are you going to update (5.1.2)?
Click to expand...
Click to collapse
If i Get it then yes for sure
Op updated with the bootloader fix, which helps to revert to old bootloader menu.
Op updated with new tool which includes OOS 5.1.2.
Mate she worked a charm! I wasn't bricked but wanted to restore to full stock after issues with open beta rims, firmware and AOSP roms. Was the simplest way to achieve a fresh start
it downloads the ROM while flashing? Or ROM is included in given link by OP?
Hi, my wife gifted me that Chopin phone form China, after a wrong "flash and lock" global firmware now my phone is stuck on bootloader.
According to this thread:
Redmi Note 10 Pro 5G brick
Redmi Note 10 Pro 5G Chinese version with fastboot unlocked. After unsuccessful firmware. At startup, it goes into fastboot, you can load it into recovery. Wipe doesn't help. When trying to flash through fastboot MiFlashPro "FAILED (remote: 'not...
forum.xda-developers.com
I have all the files needed to setup sp flash and try to put again the Rom in the phone, which is now not unlocked and no usb debugging on.
Can someone please give me a tutorial on how to use those files? My phone still not recognised in sp flash com port, I don't know how to do.
If anyone will help me it will be so appreciated, thanks!
If you need to disable authorisation, did you run the MTK Auth Bypass tool and get the message "Protection disabled"? That's what I had to do before SP Flash Tool would flash the phone (without disconnecting it or rebooting), and I also had to set the baud rate to 921600, although that was all under Linux, and the phone was still unlocked.
it's complicated. with phone locked fastboot commands don't work. with my hold mi a3 fastboot flashing unlock command work. but with miui and mtk chipset probably it's useless. but u can try. if u boot into bootloader with mediatek driver the pc should recognize your phone also if it's blocked
1: Unzip this attached file into a folder. run it.
2: select the unlock bootloader and start, then connect you phone via usb with all three buttons pressed. (Phone must be off before connect, )
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3: Your bootloader will be unlocked.
4: Close the program and re-start again, this time, select auth bypass and start, then repeat the phone connection. after at the bottom line, it show bypass ok.
from here you may flash again rom via Miflash or SPflash.
P.S: I think the file size is too big, I can not attach it here. Sorry! P.M me if you wish.
Thanks for the help, the problem I'm facing it's Auth tool cont recognise the phone, when I open the shell keep saying waiting for the device.
Driver are mtk with Libus installed, dunno.
When I restart the phone immediately have the logo then, if volume up I can log mi assistant or with volume down the bootloader screen.
Bonscia said:
Thanks for the help, the problem I'm facing it's Auth tool cont recognise the phone, when I open the shell keep saying waiting for the device.
Driver are mtk with Libus installed, dunno.
When I restart the phone immediately have the logo then, if volume up I can log mi assistant or with volume down the bootloader screen.
Click to expand...
Click to collapse
1. Check your device driver for USB, suggest you re-install the MTK usb driver.
2. First run the program, select the Auth by pass then press start.
3. Make sure phone is in "power off" state, press Vol+, Vol- and power (all three at the same time), and don't release it, plug in USB cable and wait.... Don't release these three buttons until it is Auth by pass OK.
During this process, take a look at device manager, there must be one item like portable device - USB ( Com 3). keep flashing.
sure u add reinstall mtk driver
Tried many drivers, always same result:
Driver says the device can't start. Tried to install lisbus too but no changes.
Bonscia said:
Tried many drivers, always same result:
View attachment 5499127
View attachment 5499129
Driver says the device can't start. Tried to install lisbus too but no changes.
Click to expand...
Click to collapse
you "must" remove (uninstall) the driver first then re-install the MTK usb driver again.
kirinin said:
you "must" remove (uninstall) the driver first then re-install the MTK usb driver again.
Click to expand...
Click to collapse
I did that many times, with win 10 no drivers signed mode, with many different mtk drivers but nothing was working. I'll try clean my windows and then start again with the drivers.
Bonscia said:
I did that many times, with win 10 no drivers signed mode, with many different mtk drivers but nothing was working. I'll try clean my windows and then start again with the drivers.
Click to expand...
Click to collapse
is a win10 problem that i also haved. hard to solve. u can try windows 7 via virtualbox (solved a lot of my problems in the past) or format and install a modded version of win10 (but i dont suggest this)
Virtual box looks no longer available, I'll install a fresh copy of win 7 in another partition, never give up lol
virtualbox is available for all system. i have a win7 virtualized under my linux pc, and miflash works fine. no bugs. if my tips makes you happy dont try. is not my problem, i didnt bricked my phone. i dont make things without know what i'm doing. good look. u can buy a new phone if u prefere
wetito said:
virtualbox is available for all system. i have a win7 virtualized under my linux pc, and miflash works fine. no bugs. if my tips makes you happy dont try. is not my problem, i didnt bricked my phone. i dont make things without know what i'm doing. good look. u can buy a new phone if u prefere
Click to expand...
Click to collapse
? I've just told you I've tried to download virtual box for win 10 but it's not avaible now or server was temporarily down for the download, so my only way it's to set up a fresh copy on win 7 on my pc, I can't understand your hanger answer.
kirinin said:
1: Unzip this attached file into a folder. run it.
2: select the unlock bootloader and start, then connect you phone via usb with all three buttons pressed. (Phone must be off before connect, )
View attachment 5498521
3: Your bootloader will be unlocked.
4: Close the program and re-start again, this time, select auth bypass and start, then repeat the phone connection. after at the bottom line, it show bypass ok.
View attachment 5498523
from here you may flash again rom via Miflash or SPflash.
P.S: I think the file size is too big, I can not attach it here. Sorry! P.M me if you wish.
Click to expand...
Click to collapse
Hi, can you share this Zip file with link drive or mega?
Thanks in advance
Which zip file? I have only this one
https://forum.xda-developers.com/attachments/mtk_bypass_final-rar.5444529/I
finally flashed the Rom with so flash but now the phone reboot in assistance mode sayings "NV data corrupted" I'm about to cry
Hi, I've followed your instructions, I've finally flashed the Rom into the phone, but now phone bootloop into recovery, it says "nvdata is corrupted", I've took the scatter file from the Rom folder, how to fix that problem now? Thanks.
Link with files is this, I've seen other link don't work
Redmi Note 10 Pro 5G brick
Redmi Note 10 Pro 5G Chinese version with fastboot unlocked. After unsuccessful firmware. At startup, it goes into fastboot, you can load it into recovery. Wipe doesn't help. When trying to flash through fastboot MiFlashPro "FAILED (remote: 'not...
forum.xda-developers.com
Download MTK Universal Tool V5 | MediaTek All in One Tool Latest Free
MTK Universal V5 Tool is a small MediaTek All in One Tool designed to disable user locks, bypass FRP, Auth Bypass, Format Data (user data format),
www.gadgetsdr.com
Bonscia said:
Hi, I've followed your instructions, I've finally flashed the Rom into the phone, but now phone bootloop into recovery, it says "nvdata is corrupted", I've took the scatter file from the Rom folder, how to fix that problem now? Thanks.
Click to expand...
Click to collapse
try wipe data. also u can control the active slot. try change it and reboot
Hi, finally I can install the Recovery V12.5.16.0.RKPCNXM rom and the engineering rom but have no baseband and no IMEI. Tried many times to put my IMEI codes with no luck, looks I need the mt6893 modem file to use sn writer but no way to find them on net, can someone share those files please? Thanks
MIFLASHPRO PROCEDURE
The MiFlashPro procedure is easier (and the easiest to recover your hard-bricked device), as you do not require the installation of any other external program (like python used in MTK Client for example (expect, of course, the drivers)
MTK Client is a more complicated installation as it requires the installation of Python and Git, which can be harder to use commands for people that don't or never used Python and Git, but gives you access to lock and unlock your bootloader with no 168 HOURS wait
In general, newer MTK chips are really easy to unbrick, even from a hard-brick, as it does not requires to open your phone and test-point it (especially this forum MTK 6833), compared to Snapdragon chips, which is the opposite and even costs 25€ to have a "Authorized Mi EDL Account". Keeping that out of the way, lets get to it
FIRST OF ALLInstall the MTK Preload/BROM VCOM drivers for your computer to recognise your phone in BROM state and follow the instructions given in the installation. Attached at the end of the thread
And download any MIUI ROM version from any trusted website (my favorite is mifirm.net, it downloads faster)
INSTALL MIFLASHPRO Attached at the end of the threadThere's two different Mi Flash(es). Mi Flash and Mi Flash Pro.
Mi Flash is only used to flash MIUI in your device, nothing special, probably everyone knows about it.
Then theres Mi Flash Pro (MFP for short). It's an All-In-One (AIO) tool, as shown below.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
We got the some tabs, but let's focus on the "Recovery" and "SP Flash" tabs, as we do not need the other ones.
Recovery - Recovery flashing. If your device is only booting to Recovery (which can be possible, since someone here has got a case that couldn't boot to fastboot neither system, only to recovery), by writing both your device IMEI's on the spaces, then clicking "Refurbish" leads to a more advanced factory reset than just wiping your data normally. This can get you out of recovery and go back to MIUI however. If it's not your problem, then follow on.
SP Flash - The famous SP Tool. SP Tool is a easy tool to use, may be confusing at first, but then first time a charm and you can get used to it, easily, or after some times. SP Tool is famous for recovering many MTK devices from hard bricks, and thats what we will use to recover your device.
OPEN SP FLASH UP
Here you are, greeted by a nice interface. There's nothing, but I will explain you to it.
There's 3 blank spaces, called Download-agent (DA for short), Scatter-loading file & Authentication file.
DA is to have access to the devices internal storage to be able to do the flashing;
Scatter-loading shows you the mapping of the partitions it will flash on the MTK;
Authentication is just the MTK protection for newer mtk devices that you need to be able to flash (*its also used to successfully flash, but you still need to bypass it somehow, as you require a Mi Account able to do BROM flashing, see below as you follow the thread)
Now, fill the blanks up:
To find the DA, it is always in the MiFlashPro installation location, so ...\MiFlashPro\. Access that folder, open up "\SP_Flash_Tool_V5" folder, and you will find a file named "MTK_AllInOne_DA.bin", use it as the DA.
To find the authentication file, its located in the same path of the DA, so ...\MiFlashPro\SP_Flash_Tool_V5\, and you will find a file named "auth_sv5.auth", use it as the authentication file.
Finally, to find the scatter-loading file, it is in the ROM folder you extracted, so ...\camellian_xx_xxxx_images_VXX.X.X.X.xxxxx_XXXXXXXX.XXXX.XX_XX.X_xxxxxl\ (the X's represent your MIUI version you downloaded). The scatter-loading file is always located in the folder "images", so \camellian...\images\, and you will find a text file named "MT6833_Android_scatter.txt", use it as the scatter-loading file.
Done?
Don't flash it yet, as we need to fix a issue with "combo_partisize_check".
Open up the scatter-loading file with Notepad or any text editor, so the text file named "MT6833_Android_scatter.txt".
Now, use the locate function to locate the following:
combo_partsize_check: true
After finding the first one, replace the "true" to "false", and the following one, and so on, till every line of them is set to "false" and isn't able to locate any set as "true".
We are done and finished setting up SP Tool!*Now, we need to bypass the Authentication of our device. Why? Just as the Snapdragon chips, Xiaomi has also implemented a security layer where you need to log in with a "Authorized Mi Flashing Account", which costs money (generally only on Snapdragon devices, I am not sure if we can find any paying service for it), which is really easy to bypass due to BROM.
Download the file "mtkauthbypass.zip" attached in the thread below.
Extract it, open it up, and it looks like this:
Now, press the "Disable Auth" button, you will have 60 seconds to get ready, get your hands on the phone and press at the same time the VOL+, VOL- & POWER button, till you see prompt appearing in the blank space. Should be similiar as this:
(thanks to chopwell20 for image)
After that, immediately open up SP Tool, and press "Download" as fast as possible.
Let it flash, from 5 to 15 minutes.
After it finishes, a blue window with a checkmark appears, disconnect your phone, and just press down the POWER button to boot it up.
And thats it! You have recovered your phone!If you have any issues or it didn't work out, please reply so someone can help you out
(Simplified image to understand better without explanation)
ISSUESCONNECTIONS ISSUE is completely normal!
It is when you try to connect your phone in BROM mode to your computer, but it always shows the error symbol over it.
From what it seems, this should be a issue from the phone and not your computer or the drivers itself
It doesn't mean that it makes you unable to unbrick it, but a lot of patience, as with this issue you will require to keep trying over and over again to bypass it.
So, if you can't bypass the Auth, this is probably it. Just keep trying and trying over again till you get it. There's (probably) no workaround rather than having patience to do it
(This also happens to me every time, so I consider it normal, and with some users such as bg0169 having this same issue, I just considered this was important to address it out, but if you think its not this issue, then reply, better safe than sorry)
I made this thread due to some users bricking their devices, and for every new user that hard-bricks their device to hopefully make this to help them
Amazing guide.
Thanks. and missing screenshot where Authbypass gives you prompt.
SP Flash Tool gives error on "gz.img, rescue.img and cust.img" because verified boot is enabled.
Is it possible to bypass it? or how do i disable verified boot without fastboot access? is my device completely dead?
Reelin said:
SP Flash Tool gives error on "gz.img, rescue.img and cust.img" because verified boot is enabled.
Is it possible to bypass it? or how do i disable verified boot without fastboot access? is my device completely dead?
Click to expand...
Click to collapse
yes, it is bypassable.
you just go to the mapping, and disable the checks on those partitions. it will still boot normally, afterwards, if you want (which is not necessary), you can reflash your phone via fastboot and miflash for those partitions to be flashed correctly
1lopes said:
yes, it is bypassable.
you just go to the mapping, and disable the checks on those partitions. it will still boot normally, afterwards, if you want (which is not necessary), you can reflash your phone via fastboot and miflash for those partitions to be flashed correctly
View attachment 5895435
Click to expand...
Click to collapse
Thanks for your reply.
Unfortunately, my phone won't boot when i exclude those images. No vibration, no black screen and no fastboot/recovery.
The another bypass method which requires using readback also doesn't work. I think it's probably because mt6833 is a newer chipset compared to the ones used in tutorials.
Any other advices please? I really don't want to pay money just to use MIUI again.
Reelin said:
Thanks for your reply.
Unfortunately, my phone won't boot when i exclude those images. No vibration, no black screen and no fastboot/recovery.
The another bypass method which requires using readback also doesn't work. I think it's probably because mt6833 is a newer chipset compared to the ones used in tutorials.
Any other advices please? I really don't want to pay money just to use MIUI again.
Click to expand...
Click to collapse
Could you give me more details about the another bypass? I dont understand what do you mean.
If that did not work, then I suppose your bootloader is locked
Please download the engineering ROM > https://mifirm.net/model/camellian.ttt#files;
and flash it via SP Tool like you did to MIUI, then boot to fastboot and flash an EEA image > https://mifirm.net/model/camellian.ttt#eea (if i am correct, EEA images are allowed to be flashed even with locked bootloader.)
If you do get the same verified boot error, disable those partitions to flash once again
If these methods didnt work, you need to install MTK Client to unlock your bootloader and try to reflash via fastboot or SP Tool
1lopes said:
Could you give me more details about the another bypass? I dont understand what do you mean.
If that did not work, then I suppose your bootloader is locked
Please download the engineering ROM > https://mifirm.net/model/camellian.ttt#files;
and flash it via SP Tool like you did to MIUI, then boot to fastboot and flash an EEA image > https://mifirm.net/model/camellian.ttt#eea (if i am correct, EEA images are allowed to be flashed even with locked bootloader.)
If you do get the same verified boot error, disable those partitions to flash once again
If these methods didnt work, you need to install MTK Client to unlock your bootloader and try to reflash via fastboot or SP Tool
Click to expand...
Click to collapse
My father took my phone and paid to repair it. Well, i guess thats a way to fix things...
Anyway, the other method i was talking about was the one using PGPT image and using Hex editor blah blah blah.
By the way, now my phone works but it seems NVRAM was deleted. My IMEI doesn't show up. Can i recover it without using temporary methods?
Reelin said:
My father took my phone and paid to repair it. Well, i guess thats a way to fix things...
Anyway, the other method i was talking about was the one using PGPT image and using Hex editor blah blah blah.
By the way, now my phone works but it seems NVRAM was deleted. My IMEI doesn't show up. Can i recover it without using temporary methods?
Click to expand...
Click to collapse
I dont know how to recover IMEIs since I always back my NVRAM and write it via MTK Client.
You can try this guide:
Thread '[QUICK GUIDE][HOW TO] Unbrick Camellia/Camellian and restore IMEI' https://forum.xda-developers.com/t/quick-guide-how-to-unbrick-camellia-camellian-and-restore-imei.4502077/
Alternatively, which I am not sure, try looking up a IMEI writer program somewhere in the web for MTK
---------- full quote removed ----------
Bro i need help
I followed the process as is, everything went well, I marked the blue box with the checkmark, when I turned on my device it was still the same, what do you recommend I do?
sorry for my bad english, i am using a translator because i am spanish speaking
TheZian said:
Bro i need help
I followed the process as is, everything went well, I marked the blue box with the checkmark, when I turned on my device it was still the same, what do you recommend I do?
sorry for my bad english, i am using a translator because i am spanish speaking
Click to expand...
Click to collapse
That is weird, are you able to boot into recovery or fastboot?
Did you get any verified boot error?
Did you use the right firmware? If so, what version (MIUI version (Indonesia/EEA/MI, etc.), Android version and Codename)? If you used the latest one (MIUI 14 Android 13) please try MIUI 13 Android 12 or lower
Try this:
Post in thread '[SOLVED] RN10 5G Hard-bricked after installing GSI' https://forum.xda-developers.com/t/solved-rn10-5g-hard-bricked-after-installing-gsi.4563191/post-88302451
Esto no debería pasar.
¿Eres capaz de reiniciar en fastboot o recovery?
¿Obtuviste algún error de arranque verificado (verified boot)?
usaste el firmware correcto? si si, cual version (version de la MIUI (Indonesia/EEA/MI...) version de la Android y codename)?
1lopes said:
That is weird, are you able to boot into recovery or fastboot?
Did you get any verified boot error?
Did you use the right firmware? If so, what version (MIUI version (Indonesia/EEA/MI, etc.), Android version and Codename)? If you used the latest one (MIUI 14 Android 13) please try MIUI 13 Android 12 or lower
Try this:
Post in thread '[SOLVED] RN10 5G Hard-bricked after installing GSI' https://forum.xda-developers.com/t/solved-rn10-5g-hard-bricked-after-installing-gsi.4563191/post-88302451
Esto no debería pasar.
¿Eres capaz de reiniciar en fastboot o recovery?
¿Obtuviste algún error de arranque verificado (verified boot)?
usaste el firmware correcto? si si, cual version (version de la MIUI (Indonesia/EEA/MI...) version de la Android y codename)?
Click to expand...
Click to collapse
I use MIUI 12 global version, and can't access fastboot or recovery mode, it didn't give me any error either, and I think I use the correct firmware version.
TheZian said:
I use MIUI 12 global version, and can't access fastboot or recovery mode, it didn't give me any error either, and I think I use the correct firmware version.
Click to expand...
Click to collapse
Try this:
Post in thread '[SOLVED] RN10 5G Hard-bricked after installing GSI' https://forum.xda-developers.com/t/solved-rn10-5g-hard-bricked-after-installing-gsi.4563191/post-88302451
I am unable to use MTK Auth Bypass Tool on my device. It shows an error message 'MTK Auth Disable (SLA/DAA) error!' Can you please help me?
Addendum_expired said:
I am unable to use MTK Auth Bypass Tool on my device. It shows an error message 'MTK Auth Disable (SLA/DAA) error!' Can you please help me?
Click to expand...
Click to collapse
I get the same error, anybody know how to fix?
And there is a "MediaTek Preloader USB VCOM" displayed in the Windows Device Manager.
Reelin said:
SP Flash Tool gives error on "gz.img, rescue.img and cust.img" because verified boot is enabled.
Is it possible to bypass it? or how do i disable verified boot without fastboot access? is my device completely dead?
Click to expand...
Click to collapse
I did have an issue but did not really go through all these stress...I also unbricked it using Brom and my original stock ROM files
Addendum_expired said:
I am unable to use MTK Auth Bypass Tool on my device. It shows an error message 'MTK Auth Disable (SLA/DAA) error!' Can you please help me?
Click to expand...
Click to collapse
Shilze said:
I get the same error, anybody know how to fix?
Click to expand...
Click to collapse
Please try this:
Post in thread '[SOLVED] RN10 5G Hard-bricked after installing GSI' https://forum.xda-developers.com/t/solved-rn10-5g-hard-bricked-after-installing-gsi.4563191/post-88302451
1lopes said:
Please try this:
Post in thread '[SOLVED] RN10 5G Hard-bricked after installing GSI' https://forum.xda-developers.com/t/solved-rn10-5g-hard-bricked-after-installing-gsi.4563191/post-88302451
Click to expand...
Click to collapse
It doesn't work, I think the problem is that the boot mode is bootloader instead of bootrom.
Shilze said:
It doesn't work, I think the problem is that the boot mode is bootloader instead of bootrom.
Click to expand...
Click to collapse
if your phone is displaying the 3 boot modes in the edge, then yes you are in bootloader*
you should restart to any mode, then right as it reboots you shall boot into BROM immediately and redo the same process
I think that when I press the volume up (+), volume down (-), and power buttons on my phone simultaneously, it doesn't seem to recognize any device. However, when I only press the volume up (+) and volume down (-) buttons, it recognizes a MTK Preloader USB VCOM port, and during the process, it seems to attempt to connect twice when "Disable Auth" is enabled. In addition, the BootMode displays as BootLoader