Related
I can turn on the milestone with the power button but when the OS has booted up it becomes unresponsive, if i keep pressing it it sometimes goes to the power off menu but besides from that it does not work
also i can no longer boot into the bootloader but recovery still works, the last rom i installed was the cronos rom with the included kernel, i used this rom for most of the day and it was fine untill i got home
hopefully someone can help
so...no one has any idea what i can do?
Hi silvacrest, I know this is a very old post (in Internet years), but have you (or somebody else) by any chance found a fix for the problem you described? My Milestone running CM7.2RC1 just started to present those same symptoms.
Thanks!
I have the same problem, started an hour ago, i don't know why, someone please help!
Try taking the battery, SD, and SIM out and using a can of compressed air (NOT an air compressor machine, those pull tons of moisture out of the air and can cause serious damage to your phone) on every nook and cranny of the device. Around and in the headphone port, around the power button, everywhere inside the battery compartment, etc. You'd be amazed at what problems dust can cause.
Thank you for the advice, I'll try that and keep you updated!
Sent from my Milestone using xda premium
Don't recommend this.
You will break the button for good and you'll need to open your phone, well if think you already need to do that.
The milestone button is composed of a thin foil glued to a metallic case, the glue gets old and the adherence with time will decrease and the foil will get dislocated from it's location. This is why your buttons won't work anymore.
If you use compressed air will probably break the button. I have fixed mine by putting a little thin foil of duct tape after I put the foil button in place.
Good luck.
There are more than enough videos out there that shows how to open the milestone.
Hi i2gh0st, in my case, the milestone now sometimes acts as if the power button was pressed, long or short press, waking up the device, displaying the menu or even boot when the phone is off.
You think this behavior could correspond to the foil problem you described?
I don't think so, the button should not work at all, unless it got stuck on press mode. Anything is possible its a ****y button if you look at it from an engineering way.
When I assembled my phone last time I noticed the volume up didn't work, so I opened it again and I found the foil glued to another place instead of its location. So everything started to make sense why buttons break down.
Sorry if I don't really make myself understood, I'm not that good at technical English.
Oky, can't find any relevant video or picture to show you, so I'll open my phone again in week-end after my exam and make a video or some pictures. Just wait a little
power button: Too recessed and flat, to the point where I now have to use my fingernail to power on the device.
volume button: Flimsy to the point where I can literally slide it up and down. I can also hear it jingle when the device vibrates.
Backcover Flimsy, moves around too much and is never tightly secured.
hardware: When I unplug my device from the charger and the screen is getting ready to time out, it flashes green, then times out... (this looks like it's going to create bigger issues down the road)
Power button: 1 in 20 HD7's I have exhibited the behavior you mention. It went away however. I would advise against using your fingernails if at all possible.
Volume Button: Again, 1 in 20 have this, and unfortunately it's the one I carry around. Two other HD7's I personally used did not have this.
I'd try to get it replaced if I were you.
I'm 2 for 2 on the first two annoyances (power and volume button).
I'm getting it replaced again (for the third time) tomorrow morning. I've also noticed these problems with the store models at various T-Mobile stores.
If I have the same problem with my third device, I'm returning it and getting my refund. Omnia 7, here I come.
Hmmm... I don't care much for the power button placement, but I haven't seen any of the other things you mentioned.
jimbonics said:
Power button: 1 in 20 HD7's I have exhibited the behavior you mention. It went away however. I would advise against using your fingernails if at all possible.
Volume Button: Again, 1 in 20 have this, and unfortunately it's the one I carry around. Two other HD7's I personally used did not have this.
I'd try to get it replaced if I were you.
Click to expand...
Click to collapse
regarding issue #1, how did the problem go away? did some mechanism inside shift causing the power button to pop out more? just wondering?
i also have the loose battery cover. very annoying.
also about the screen... havent seen this mentioned before. i have a slight gap at the left and right edges of the screen where it meets the chrome-ish border. its pretty easy for particles to get stuck in there. compared to the hd2, this gap is pretty noticeable.
I thought I was the only one with these issues lol, figured the recessed power button was just a design oversight
@jimbonics: just wondering, but why do you advise against using your fingernail?
Sent from my T-Mobile G2 using XDA App
jimbonics said:
Power button: 1 in 20 HD7
Volume Button: Again, 1 in 20 have this
Click to expand...
Click to collapse
Seriously? I checked a batch of HD7 in malaysia, and exceptionally, all of them had this issue. You're just so lucky you dont have it
daaango said:
why do you advise against using your fingernail?
Click to expand...
Click to collapse
Maybe because of this ?
Thanks Shu and daaango.
I knew I wasn't crazy in thinking this was an issue only I was experiencing.
I've also read several phone reviews, and a lot of the reviewers mentioned about the power button being recessed and stating frustration waking up the device.
I don't know how HTC can fluff up something so important. I mean, what good is a product if you can't power it on; wake it up? One would think they would put emphasis on having a solid foundation on the power button.
Melcali: Yeah, on one phone the power button managed to become flushed, to the point the user had to use their fingernail (even though i found it easy to turn on with the flat of my finger, almost like it was capacitive). However, next day it had 'popped out' a bit and had become less recessed and hasn't been a problem for him since.
daango: In addition to what Shu posted, using your fingernail is likely going to cause you to press the button in harder than it needs to be, which would likely cause the button to be crammed in more and more over time. If it can't be prevented, it can't, I'm just advising against it.
I've got two unopened spares. I'm going to crack them open and see if the volume button jiggles.
Ah, thanks shu and jimbonics for explaining that
Honestly, I don't think it can be helped. Maybe my fingers are too round or something, but using my fingernail seems like the only option right now. I might try adding layers of tape on the button so its easier to press but idk yet... it might take away from the aesthetics
Sent from my T-Mobile G2 using XDA App
All five units I've come across so far -- my defective original (corrupted memory), my current one, a second defective one (also corrupted memory), its replacement, and an in-store demo phone -- have the same issues:
Recessed power button
Very difficult to press camera button (basically useless)
Loose volume rocker (the case opening is about 0.8 mm too long for the rocker, so it moves around)
Imperfect battery cover fit (the plastic cover flexes from the opening process, so usually doesn't fit perfectly)
Weak screen support in bottom-right (press a bit on the search key and you'll see waves on the LCD)
On the two that I've had long enough to use, the clear coat on the kickstand is flaking off, and the Windows Phone logo, which was barely visible to begin with, has almost completely faded away on one of them.
Kind of sad that HTC screwed up so badly given that the HD7 is a barely-modified HD2, which was among the best-built phones on the market.
amb9800 said:
All five units I've come across so far -- my defective original (corrupted memory), my current one, a second defective one (also corrupted memory), its replacement, and an in-store demo phone -- have the same issues:
Recessed power button
Very difficult to press camera button (basically useless)
Loose volume rocker (the case opening is about 0.8 mm too long for the rocker, so it moves around)
Imperfect battery cover fit (the plastic cover flexes from the opening process, so usually doesn't fit perfectly)
Weak screen support in bottom-right (press a bit on the search key and you'll see waves on the LCD)
On the two that I've had long enough to use, the clear coat on the kickstand is flaking off, and the Windows Phone logo, which was barely visible to begin with, has almost completely faded away on one of them.
Kind of sad that HTC screwed up so badly given that the HD7 is a barely-modified HD2, which was among the best-built phones on the market.
Click to expand...
Click to collapse
wow, you have had a lot of problems. I'm still on my original hd7 since second week of november.
1. power button is slightly recessed, but no problems pushing it with my finger (not nail)
2. camera button does have some orange on it, but it functions properly.
3. volume buttons work fine, maybe a little slide to the rocker, but doesn't effect controls
4. no flaking of clearcoat, no wp7 logo coming off, no lcd discoloration no matter how hard I press on the search or back buttons.
5. Back cover fits properly. I haven't had much reason to pull it off after initial placement of sim card, thanks to phone not constantly freezing. There is a slight gap where the back cover meets the smaller cover.
What are you subjecting your phones to???
I agree the hd7 build quality might not be iphone, but it's holding up well for me. It's not like we have a lot of choices on t-mobile, the dvp has way more problems at this point.
amb9800 speaks the truth. I went through 3 different units that had defects to varying degrees. I had similar issues with the EVO as well. HTC are notorious for shoddy craftsmanship.
I have the same problems they started AFTER my 30 days .. So i havent tryed to go and change at my local T-Mobile!! Is there any loop in the contract or something that would let me change it for anither phone and pay difference/get a refund xD
have the same problems as the op
So, i was using xperia z for 2.5 weeks and everything was great so far.
But four or five days ago i noticed that power button changed the way it presses. Now, if i havent turn the screen on for some time, the button makes a little crunch when it is touched. This effect repeats in lighter way on the secong press of the button, and there is no such issue if button is in constant use. But the problem appears again, if device has not been used for an hour or more.
And the proccess of pressing is sort of going in two stages: in the beginning goes the crunch (the feeling is like the button scratches something with some resistanse. There is also a little dangle of the button while unpressed), next the gap ends, button touches its membrane smoothly and silently. Sure, the issue is not really unbearable, but it does concern me as it is the only big problem i experienced on my device.
So, should i wait for issue to disappear itself, is it possible to make any steps to improve the situation on my own or is it better to visit service centre at once?
I forgot to mention this: device has been used gently and carefully, it has never fell down, it has never been used or carried in conditions that could possibly make damage to button, neither sand nor dirt could penetrate button's mechanism and so on.
Get a replacement to be honest I wouldn't want water getting in. Sounds like the button has loosened or something.
This has happened to people with game controllers with the Wii, ps3 Xbox etc
Sent from my LT26i using Tapatalk 2
The problem has surprisingly disappeared today. There is still a little gap, but annoying sounds went away and the pressing of button feels just fine.
I guess i'll immediately visit service center if the issue will happen again, though.
Doesn't matter on the placement too much as sometimes my watch will reset because I bent my hand and it hit and held the middle button causing it restart. Is there something I can fill in the space with to stop the button from pushing down? Maybe a very tiny elastic band?
Or you can wear it on your right hand?
Go to a watch shop, most new watches come with the crown held out with a small plastic disc. Maybe one of these might fit.
re: middle button
worldsoutro said:
Doesn't matter on the placement too much as sometimes my watch will reset because I bent my hand and it hit and held the middle button causing it restart. Is there something I can fill in the space with to stop the button from pushing down? Maybe a very tiny elastic band?
Click to expand...
Click to collapse
You must be double jointed or something, I tried to bend my wrist a half a
dozen times as hard as I could and even slid the watch as close as I could
to my wrist trying to intentionally press the button but I could not do it.
Good luck!
Have a great day!
I have done it twice in a week.
Happens to me all the time, also beware the button is easily broken as I have learnt. The watch fell while putting it on and landed on the button and it no longer works
harlin73 said:
Or you can wear it on your right hand?
Click to expand...
Click to collapse
Happens to me Several Times a Day,, many times it will reboot,, if i try to attach my watch higher than the wrist bones my shirt or jacket will cover the watch face and i will have to use my other hand to expose the face,, very annoying when all you want to do is Glance at the Watch face for the time or messages that just came through,,, By the Way Switching to my Right Hand Does Solve the Issue of Accidentally Pressing the Button But Very Annoying and Makes it Extremely difficult to press the Buttons with my left hand
This was one of the most frustrating things I ran into with my ZW3, as it happened all the time. However, there is a fairly easy solution. Flip it around so that the buttons are on the opposite side, then run Set Orientation to force the screen to match. Problem solved.
If you are comfy setting up your phone as an ADB bridge, you can upload the APK on the fly. Otherwise, you will need to plug it into a PC and upload over ADB the ordinary way. However, getting the Set Orientation app on the watch is the hardest part of the whole deal.
Hi, I dropped my phone by accident and unfortunately, it fell on the volume key which is now bend in the middle and stuck pushing vol up.
I can push volume down but the key is stuck with volume up and the phone would do that at random. For example, at some point during a call it would go to maximum volume automatically, which is super annoying.
Does anyone have experience with replacing hardware parts of the Zenfone 8? I watched this tear down video , it looks kind of easy to disassemble. However I am not sure if I can reach the volume key without removing the main board. Also, not sure if will be water proof after reassembling (guess not, but no problem).
Any tips? Thanks everyone!
I tried searching a bit but couldn't find any Zenfone 8 buttons (though maybe buttons from other phones could work). What I found instead is a complete frame that does come with the buttons attached to it, so you could either transfer the whole phone internals to it, or try removing the button to put inside your original casing. (I think the second option would be easier since the battery is glued down pretty solidly)
Anyways, here is the link: https://www.aliexpress.com/item/1005003661617745.html
I think it will not be water proof after you open it, so you should also consider getting a new seal. (Consider that I have never openned my zf8 lol so I am not pro). But from what it looks like, it will most likely be easier and safer for the board to remove it before playing on the side and risking slipping and scratching the pcb
EDIT: I found the specific volume key on asus-accessories.com for 12$!!
Thanks for your help! I already found and ordered the spare part on https://www.fixshop-online.de/ I hope that 24 Euros are not wasted.
Hopefully, the whole open and repair process will not be too difficult.
DerSteppo said:
found and ordered the spare part
Click to expand...
Click to collapse
I would be very interested in the results. Most importantly, if the spare part is a good quality replacement. Also I would be interested in how easy or hard such a replacement is. I looked into many of the teardown videos before buying the device, but those are usually from super-experienced pros with all the fancy tools. I would be interested in a first-hand report, even if it's short.
I will keep you updated. A friend sent some special adhesive tape but it hasn't arrived, so I didn't start disassembling.
The spare part, however, seems to be not available. I received an email that they don't have it. So I wait a little, maybe they can order it, but if it will not arrive end of April, I will just try to fix the bent old one.
@amenthes
I managed to open the phone with a hairdryer. I probably should have applied more heat, but I was hesitant because I did not want to destroy something, so it was a little bit harder to remove the back cover with a plectrum-like tool. Around the rim of the cover is a black adhesive tape, which I completely removed without any traces.
Unfortunately, I received another email that the spare part was not available, so I (not wanting to wait for a month or longer) cancelled the order eventually. Problem was, the volume button is somehow fixed to the case and I could not reach it properly. I managed to push it back a little bit, but could not remove it for replacement. During the process, I damaged the lower volume contact (as I wrote, the part is hard to reach) unfortunately. So now the volume down button does not work at all. However, the volume up button now does not get triggered automatically anymore. So I just push vol+ and lower the volume on the screen or via bluetooth headset. Works for me, as long as it doesn't go max. volume all of a sudden anymore.
A friend gave me some double sided adhesive tape which came with his replacement battery and I cut it with a razor blade to fit the back cover. It does not go all the way around, but I don't want to take the phone into water anyways. Besides, it looks just as it has never been opened. No gap at all, so the opening and closing parts are fairly easy.
All in all, it has been an experience. I will keep the phone despite the broken button, because for me it is still one of the best phones available at the moment.
Thank you for reporting back
@amenthes
Hi, it's been a while but I finally managed to replace the button!
I found a spare part on AliExpress. Not only was it much cheaper than on the other website, it is the whole middle frame instead of the button only. Delivery was expected end of June, however it arrived today (yeah!).
I used a razor blade and a thin needle as lever to remove the new button from the frame, since there seems to be no way from the inside without making things too complicated.
To remove the old button from the phone, which was bent and messed up (I tried to rip it off with a needle-nose pliers, but it did not work and it left some ugly marks), I used a sharp knife instead. I got inspired by this teardown video of another phone which unfortunately I don't remember. In the video, the guy used the knife like he would peel an orange. Like you would try to cut the button from the top edge. If enough pressure is applied you can pull the button out.
Eventually, I inserted the new button and pushed it a few times from different angles and now it feels almost as new. There is a nice click and pressure point. So I consider this a win.
At the end of the day, I did not even have to open the back of the phone with this method, but I learned a few things, which is nice, and, you know, you never know. Also, it gave me some confidence in my technical skills.
DerSteppo said:
@amenthes
I managed to open the phone with a hairdryer. I probably should have applied more heat, but I was hesitant because I did not want to destroy something, so it was a little bit harder to remove the back cover with a plectrum-like tool. Around the rim of the cover is a black adhesive tape, which I completely removed without any traces.
Unfortunately, I received another email that the spare part was not available, so I (not wanting to wait for a month or longer) cancelled the order eventually. Problem was, the volume button is somehow fixed to the case and I could not reach it properly. I managed to push it back a little bit, but could not remove it for replacement. During the process, I damaged the lower volume contact (as I wrote, the part is hard to reach) unfortunately. So now the volume down button does not work at all. However, the volume up button now does not get triggered automatically anymore. So I just push vol+ and lower the volume on the screen or via bluetooth headset. Works for me, as long as it doesn't go max. volume all of a sudden anymore.
A friend gave me some double sided adhesive tape which came with his replacement battery and I cut it with a razor blade to fit the back cover. It does not go all the way around, but I don't want to take the phone into water anyways. Besides, it looks just as it has never been opened. No gap at all, so the opening and closing parts are fairly easy.
All in all, it has been an experience. I will keep the phone despite the broken button, because for me it is still one of the best phones available at the moment.
Click to expand...
Click to collapse
Thanks for sharing your experience. Do you think the waterproofing was tempered by the repair ?
DerSteppo said:
@amenthes
Hi, it's been a while but I finally managed to replace the button!
I found a spare part on AliExpress. Not only was it much cheaper than on the other website, it is the whole middle frame instead of the button only. Delivery was expected end of June, however it arrived today (yeah!).
I used a razor blade and a thin needle as lever to remove the new button from the frame, since there seems to be no way from the inside without making things too complicated.
To remove the old button from the phone, which was bent and messed up (I tried to rip it off with a needle-nose pliers, but it did not work and it left some ugly marks), I used a sharp knife instead. I got inspired by this teardown video of another phone which unfortunately I don't remember. In the video, the guy used the knife like he would peel an orange. Like you would try to cut the button from the top edge. If enough pressure is applied you can pull the button out.
Eventually, I inserted the new button and pushed it a few times from different angles and now it feels almost as new. There is a nice click and pressure point. So I consider this a win.
At the end of the day, I did not even have to open the back of the phone with this method, but I learned a few things, which is nice, and, you know, you never know. Also, it gave me some confidence in my technical skills.
Click to expand...
Click to collapse
Thanks for sharing your experience. Do you think the waterproofing was tempered by the repair?
maxime78 said:
Thanks for sharing your experience. Do you think the waterproofing was tempered by the repair?
Click to expand...
Click to collapse
Probably yes, because I used adhesive tape and cut it myself along the back rim and it is not in one piece going all around. However, the cover sits very tight and you wouldn't even recognize that the phone was ever opened. I don't really mind because I use a silicon phone case anyway and I don't intend to take the phone underwater.
You can buy the original battery cover adhesive spare part here: https://www.asusparts.eu/en/asus-13040-01431000 but I did not want to spend more money and my solution works for me.
DerSteppo said:
@amenthes
Hi, it's been a while but I finally managed to replace the button!
I found a spare part on AliExpress. Not only was it much cheaper than on the other website, it is the whole middle frame instead of the button only. Delivery was expected end of June, however it arrived today (yeah!).
I used a razor blade and a thin needle as lever to remove the new button from the frame, since there seems to be no way from the inside without making things too complicated.
To remove the old button from the phone, which was bent and messed up (I tried to rip it off with a needle-nose pliers, but it did not work and it left some ugly marks), I used a sharp knife instead. I got inspired by this teardown video of another phone which unfortunately I don't remember. In the video, the guy used the knife like he would peel an orange. Like you would try to cut the button from the top edge. If enough pressure is applied you can pull the button out.
Eventually, I inserted the new button and pushed it a few times from different angles and now it feels almost as new. There is a nice click and pressure point. So I consider this a win.
At the end of the day, I did not even have to open the back of the phone with this method, but I learned a few things, which is nice, and, you know, you never know. Also, it gave me some confidence in my technical skills.
Click to expand...
Click to collapse
pulling out a device's button with a knife is like cutting ice cream with axe. You will always end up spoiling it.
Evan Roberts said:
pulling out a device's button with a knife is like cutting ice cream with axe. You will always end up spoiling it.
Click to expand...
Click to collapse
That's what I thought, but it worked surprisingly well actually!
@DerSteppo
Good day, sir. You have literally saved me from feeling extremely sad and even considering taking my phone to repair shop (which I never did in my life).
My story: I was snowboarding some days ago and at one point I fell on the slope on high(ish) speed. It was okay until I took a lift and took a look at my phone. It was almost exactly the same case as yours - the volume key was bent in the middle except it was vol. down which was stuck. Luckily the phone was still usable, I could adjust the volume via sound control panel in the settings which of course felt tedious but still not the end of the world until I get home and figure something out. Unfortunately while messing with the buttons now it was turn for vol. up to be pushed and there was no way to turn the phone on because it triggered the boot mode which wont let you out I came across that very video you mentioned and was baffled at why they made it so that you literally cant get the button from the frame without surely f**king something up in the process I started feeling anxious and thankfully google showed me this thread. All in all, I took your advice with a knife and managed to pry the buttons off a little and thankfully both buttons got released from their respective contact panels. So again, thank you so much man, don't think I could figure this out by myself
One question though. Not sure yet whether to get a new button instead of now scratched and still bent one, but was there any difficulty to insert the new button into the frame? There are two little 90 deg. angled metal things on each side and I am not sure if they can affect the insertion process.
Asus Zenfone 8 ZS590KS - Volume Button (Obsidian Black) - 13020-06381400 Genuine Service Pack | FixShop
Replacement volume button for Asus Zenfone 8 ZS590KS. Use the button if the original button has stopped working or is damaged and needs to be replace…
www.fixshop.eu
fluXion69 said:
@DerSteppo
Good day, sir. You have literally saved me from feeling extremely sad and even considering taking my phone to repair shop (which I never did in my life).
My story: I was snowboarding some days ago and at one point I fell on the slope on high(ish) speed. It was okay until I took a lift and took a look at my phone. It was almost exactly the same case as yours - the volume key was bent in the middle except it was vol. down which was stuck. Luckily the phone was still usable, I could adjust the volume via sound control panel in the settings which of course felt tedious but still not the end of the world until I get home and figure something out. Unfortunately while messing with the buttons now it was turn for vol. up to be pushed and there was no way to turn the phone on because it triggered the boot mode which wont let you out I came across that very video you mentioned and was baffled at why they made it so that you literally cant get the button from the frame without surely f**king something up in the process I started feeling anxious and thankfully google showed me this thread. All in all, I took your advice with a knife and managed to pry the buttons off a little and thankfully both buttons got released from their respective contact panels. So again, thank you so much man, don't think I could figure this out by myself
One question though. Not sure yet whether to get a new button instead of now scratched and still bent one, but was there any difficulty to insert the new button into the frame? There are two little 90 deg. angled metal things on each side and I am not sure if they can affect the insertion process.
Asus Zenfone 8 ZS590KS - Volume Button (Obsidian Black) - 13020-06381400 Genuine Service Pack | FixShop
Replacement volume button for Asus Zenfone 8 ZS590KS. Use the button if the original button has stopped working or is damaged and needs to be replace…
www.fixshop.eu
Click to expand...
Click to collapse
Hi, I am so happy to read I could help with my experience! Nice to see that you where able to fix it for now.
I did not have problems with inserting the new button, no. With the phone switched of, I just pushed it in and pressed a bit harder on both ends a few times. I think it "clicked" in at some point.
It is still working as new! One advice though: you might want to consider buying the original adhesive tape that is shaped to fit properly. I used just a few stripes and cut it to fit almost all the way around, but a few months ago I saw that the back cover was slightly lifted and there is a gap. The phone survived a few drops from various heights in the meantime, so I am not surprised. I am too lazy to re-apply new tape, though. It's in the rubber case anyways.
All the best!