Hey. When i change color on charging led light, first 1-2 seconds when i plugged phone into charger it shows me right color, but then as i said 1-2 seconds later it is always blue. Just why? I have issue only with charging color
Ok, but what does it means battery charging color? I mean there is written "when battery is charging" and i can choose color. What for is it if there will be always blue color? Thanks
Related
The only LED I ever really noticed on my Hima was the blue one telling me BT was on or off. I know the device has a green, yellow and red LED on the opposite side that can either burn or flash, but don't ask me why. Neither do I know if the flashing rate of the blue LED might tell me something.
Last week when my battery was just about 99.9% drained and my Hima started to behave strange, I noticed that on external power the red LED burned constantly. And when I notice something like that, it's probably because I've never seen it before.
http://michael-channon.spaces.live...._c=BlogPart&partqs=cat=Hermes+Charging+Issues helped me out.
But I would love to know the exact meaning of all LED colours and blinking rates.
all the Leds's Rate are in the Book that comes with it
Thanks, but as I told before I bought 2 Hima's with broken screens years ago, under those conditions it's very rare to get anything but the dead device itself.
The service manual only tells me that a fast flashing yellow LED means battery is too warm (>35C) or too cold (<0C) to charge.
hmmz..u r rite..its unpredictable..any way i'll see what i can find
What I can see, it's blinking green on normal operation, lighting yellow on charging, blinking red on missed calls and lighting red on too low voltage...
Mine never blinks green. Lighting green tells me charging reached 100%.
Could blinking green mean GPRS or IR on?
Anyone ever seen blinking yellow?
I hope curiosity only kills cats ;-)
I guessed the lighting red :-(
Mine blinking green when it is in normal operation.
Yellow on charging
Red when there is misscall or message because I set to give LED sign
> Green for normal - with carrier signal operation and Fully charged while still plugged into wallsocket
> Yellow for Charging
> Red - missed calls/poor elec current while being charged/very low battery
@Maggy, there is a tweak on how to permanently disable blinking lite even during normal operation. could it be possible that ur units have are tweaked like such?
badbadtz.carlo said:
> @Maggy, there is a tweak on how to permanently disable blinking lite even during normal operation. could it be possible that ur units have are tweaked like such?
Click to expand...
Click to collapse
Not that I can remember, but I'm tweaking all the time. Aren't we all?
;-)
how come on my XDA my colors are
Yellow=Normal Operation
ORANGE=Charging
Red=Low batt
May be your led is expired Yellow and Orange is slighly different, you lose green color I think every body mentioned yellow in here is little bit mix with orange color
Or some of us are more colour blind than others
does someone know why the diamond doesn´t have a status led to show if its charging or already fully charged. do i really have to go to the menu to see the status?
Read the manual and you will find that there is a charging led status...its the middle button...when fully charged it stays white and when charging it glows around the button.
Thanx!
Next time i'll charge it when its dark!
I updated my NC to run CM7 off the SD card and whenever I go to charge it the Indicator built into the USB cable never changes to Green when the battery is completely charged. Is always stays the yellow color. Anyone else notice this?
ya same with mine it never changes colour...
For me, sometimes it turns green, other times it doesn't. Seems to charge up OK either way though.
Odd I have CM7 flashed to the emmc and it always turns green when fully charged. Is everyone who's having a problem running off SD?
jmak10 said:
I updated my NC to run CM7 off the SD card and whenever I go to charge it the Indicator built into the USB cable never changes to Green when the battery is completely charged. Is always stays the yellow color. Anyone else notice this?
Click to expand...
Click to collapse
The green indicator is not tied to the battery percent gauge on the display. It takes a few hours after the 100% reading before the green light goes on...
fpga_guy said:
The green indicator is not tied to the battery percent gauge on the display. It takes a few hours after the 100% reading before the green light goes on...
Click to expand...
Click to collapse
that doesn't sound too right. it should turn on at 100% immediately right?
and i thought i'm the only one with this problem.
bradputt said:
that doesn't sound too right. it should turn on at 100% immediately right?
and i thought i'm the only one with this problem.
Click to expand...
Click to collapse
Nope... the green light is tied to a voltage comparator. When the threshold exceeds the predetermined voltage, the light turns green.
The battery gauge is tied to a ADC (analog to digital converter). That's how it determines the percentage power left.
The two are independent. The question was previously addressed:
http://forum.xda-developers.com/showthread.php?t=1025021&highlight=battery
Replaced the battery in my Nook, it wouldn't come on or charge, now it goes to green, amber, and red blinking light. Can someone help me with getting this to work? What should I look for etc.?
Make sure your 7 pins (2 red, 2 black, 1 yellow, 1 green and 1 white) connector is properly attached, If yes, you should measure between the red wires and black wires has any voltage between them.
I'm trying to change LED notification colours in OOS (on 4.0.2, also tried on 4.0.1) and I changed 'While charging' to Cyan but it stays blue, if I replug the charger then it turns to Cyan for a sec but goes back to blue. Is this bugged in OOS or am I missing something ?
Dash Charge will always be blue. If you charge without Dash, it will be the colour of your option.