Bricked Xiaomi MI5 - Xiaomi Mi 5 Questions & Answers

Hello everyone.
Yesterday while i was trying to install a new rom in my MI5 I bricked my phone.
I wiped the system, data, cache and kernel cache, then, as a mistake I rebooted my phone and all of a sudden it turned black and I couldn't go to the recovery or fastboot.
Now the phone is just black, no response trying to boot or go to recovery\fastboot. When I put to charger theres no LED LIGHT.
So I installed the adb drivers, installed MiFlash, and the computer recognized the phone as QualComm HS-USB QDLoader 9008 COM4.
Then I installed a fastboot rom into the phone using MiFlash, it said flash done and successful.
But, it keeps freezed in a black screen.
Should I just wait for a miracle or theres another option?
My PC still recognizes the phone as QualComm HS USB QDLoader 9008 COM 4.
Thanks in advance.
// EDIT (SOLVED)
Ok so now it booted with the fastboot ROM I flashed.
As I see, after the flash it takes hours to boot. I just went home, dropped the phone in the bed, then I pressed Vol up+Vol down and power button at the same time for two minutes and worked.

Related

[Q] HTC Desire C - No Fastboot or recovery

Hi.
i got this phone from a friend, and he said it was broken (didn't say how) and it didn't turn on.
when i plugged it into my computer with a normal usb cable, it showed the phone as "Forge HS-USB QDLoader 9008 (COM4)"
iv'e tried to boot in fastboot and recovery, but the only thing that happens is that it reconnects in the same mode.
iv'e also tried to use fastboot flash anyways, but it didn't worked. same goes for adb.
if any of you have a answer to this (that don't innvoles a jtag or any box or cable like that) i'll appriciate it
(PS. Im new to this forum)

Is there anything I can do? Brick help

My Xiaomi mi5 does not turn on.
No lights, fastboot is not accessible, resetting it does not do anything.
Basically for any combination of buttons that I press, nothing happens and the screen stays black - it is completely dead.
However, when I plug it into my pc, the devices shows up as qualcomm hs-usb qdloader 9008 (COM3) which is the only sign of life from the phone.
What I want to know is if it is possible for me to unbrick the phone from this situation. I understand that I need to get into fastboot in order to flash the ROM, but is there a way to get to fastboot using my pc? Or even turn the phone on with commands? At the moment ADB and Fastboot does not recognise my phone, is there a way to make it detect it from the state it is in?
Thanks
sivd said:
My Xiaomi mi5 does not turn on.
No lights, fastboot is not accessible, resetting it does not do anything.
Basically for any combination of buttons that I press, nothing happens and the screen stays black - it is completely dead.
However, when I plug it into my pc, the devices shows up as qualcomm hs-usb qdloader 9008 (COM3) which is the only sign of life from the phone.
What I want to know is if it is possible for me to unbrick the phone from this situation. I understand that I need to get into fastboot in order to flash the ROM, but is there a way to get to fastboot using my pc? Or even turn the phone on with commands? At the moment ADB and Fastboot does not recognise my phone, is there a way to make it detect it from the state it is in?
Thanks
Click to expand...
Click to collapse
Do you have all the necessary driver installed? I think yes and that is why you are seeing in (COM3) port. You can do one thing, Unplug the phone from PC and Press and Hold Vol Down (-) and plug in again. If not works then you can also Press and HOLD Vol Down and Press and HOLD Power button until you see Fast boot menu. If don't work then try the same thing with Vol UP button. Then you suppose to see a MI phone logo with a USB cable.
"qualcomm hs-usb qdloader 9008" Is a signal of Hard Brick for QCOM devices (Like for LG G2);
http://forum.xda-developers.com/lg-g2/general/fix-unbrick-lg-g2-stuck-qualcomm-hs-usb-t2933830
As you can see here, for fix it you need all partition files, all system files, and a programm
But i dont know if it will works also on SD820, you might need all files for Mi5
Just a question: How did you bricked your phone?
EDIT:
I had an idea: maybe inside fastboot rom you can find all files you need, it might be worth a try, at least you can send it to your shop where you bought it
sivd said:
However, when I plug it into my pc, the devices shows up as qualcomm hs-usb qdloader 9008 (COM3) which is the only sign of life from the phone.
What I want to know is if it is possible for me to unbrick the phone from this situation. I understand that I need to get into fas,tboot in order to flash the ROM
Click to expand...
Click to collapse
1: if you're detecting it as qcom 9008, there's a good chance it's in EDL mode, which is good news
2: download MiFlash from here: https://www.androidfilehost.com/?fid=24521665358595574
3: download the latest dev rom from here: http://update.miui.com/updates/v1/fullromdownload.php?d=gemini&b=X&r=cn&n=
4: Extract the files to C:\
5: Open MiFlash & point the folder to the root ROM folder, example: C:\gemini_foo_bar, NOT C:\gemini_foo_bar\images
6: connect your phone & select flash all (1st option from the left, bottom of MiFlash tool)
This might take a few tries (example - you might receive "missed hello packets)
Once you're done, you can stay with the China Dev, unlock the bootloader & flash a xiaomi.eu rom, or CM.
Good luck.
adwinp said:
1: if you're detecting it as qcom 9008, there's a good chance it's in EDL mode, which is good news
2: download MiFlash from here: https://www.androidfilehost.com/?fid=24521665358595574
3: download the latest dev rom from here: http://update.miui.com/updates/v1/fullromdownload.php?d=gemini&b=X&r=cn&n=
4: Extract the files to C:\
5: Open MiFlash & point the folder to the root ROM folder, example: C:\gemini_foo_bar, NOT C:\gemini_foo_bar\images
6: connect your phone & select flash all (1st option from the left, bottom of MiFlash tool)
This might take a few tries (example - you might receive "missed hello packets)
Once you're done, you can stay with the China Dev, unlock the bootloader & flash a xiaomi.eu rom, or CM.
Good luck.
Click to expand...
Click to collapse
I also had the same issue with black screen and no responses from vol. & power buttons. But when I notice that in device manger it showed the qcom driver, then I new that there was hope to recover the phone. I can confirm that this will unbrick your phone. I MiFlash'd the China Rom (non-dev), unlocked the bootloader, MiFlash'd MiFlash_xiaomi.eu_gemini_V7.2.13.0.MAACNDB_6.0 rom, sideload lastest stable EU rom, TRWP and SuperSU.
adwinp said:
1: if you're detecting it as qcom 9008, there's a good chance it's in EDL mode, which is good news
2: download MiFlash from here:
3: download the latest dev rom from here:
4: Extract the files to C:\
5: Open MiFlash & point the folder to the root ROM folder, example: C:\gemini_foo_bar, NOT C:\gemini_foo_bar\images
6: connect your phone & select flash all (1st option from the left, bottom of MiFlash tool)
This might take a few tries (example - you might receive "missed hello packets)
Once you're done, you can stay with the China Dev, unlock the bootloader & flash a xiaomi.eu rom, or CM.
Good luck.
Click to expand...
Click to collapse
Thank you so much, this has worked perfectly and saved me a lot of money! I really appreciate your help, thank you again!
sivd said:
Thank you so much, this has worked perfectly and saved me a lot of money! I really appreciate your help, thank you again!
Click to expand...
Click to collapse
Glad you could salvage your device.
Now remember - from great flashing power comes great responsibility ;]
adwinp said:
1: if you're detecting it as qcom 9008, there's a good chance it's in EDL mode, which is good news
2: download MiFlash from here: https://www.androidfilehost.com/?fid=24521665358595574
3: download the latest dev rom from here: http://update.miui.com/updates/v1/fullromdownload.php?d=gemini&b=X&r=cn&n=
4: Extract the files to C:\
5: Open MiFlash & point the folder to the root ROM folder, example: C:\gemini_foo_bar, NOT C:\gemini_foo_bar\images
6: connect your phone & select flash all (1st option from the left, bottom of MiFlash tool)
This might take a few tries (example - you might receive "missed hello packets)
Once you're done, you can stay with the China Dev, unlock the bootloader & flash a xiaomi.eu rom, or CM.
Good luck.
Click to expand...
Click to collapse
Thanks for the guide, 1 q tho: what to do when i get the "missed hello packets, try to recover" message?, wait or restart the process?
Ok, solved by disabling driver sign (press F8 during boot)
Hello , i got the same problem as described at this topic and here is my problems :
I can't turn on my phone and i can't put it in fastboot mode ( tryed a lot of buttons combinations)
But when i plug it into my pc - it recognizes as Android
I have tryed to install drivers but windows shows mistake and can't install that
When my device connected to pc and i press volume + and power buttons - in few minutes system(WIN 10) recognizes it as ADB interface(can't install drivers too) and i have acess to mi5 internal storage ( i can download photos and so on )
But mi flash doesn't see phone in any mode and i feel that my device is still alive and i can recover it but don't know how....
I will be grateful for any help !
Isteran said:
Hello , i got the same problem as described at this topic and here is my problems :
I can't turn on my phone and i can't put it in fastboot mode ( tryed a lot of buttons combinations)
But when i plug it into my pc - it recognizes as Android
I have tryed to install drivers but windows shows mistake and can't install that
When my device connected to pc and i press volume + and power buttons - in few minutes system(WIN 10) recognizes it as ADB interface(can't install drivers too) and i have acess to mi5 internal storage ( i can download photos and so on )
But mi flash doesn't see phone in any mode and i feel that my device is still alive and i can recover it but don't know how....
I will be grateful for any help !
Click to expand...
Click to collapse
If you can see it in adb, you might be able to see it in fastboot.
Try go in to fastboot (even though you can't see it on screen.)
And try fastboot oem device-info see if you can get anything. Then we go from there.
DrBubblewrap said:
If you can see it in adb, you might be able to see it in fastboot.
Try go in to fastboot (even though you can't see it on screen.)
And try fastboot oem device-info see if you can get anything. Then we go from there.
Click to expand...
Click to collapse
tryed a lot of time to go to fastboot , but nothing happened...
same issue
I've been having the same problem with my MI5, 128gb running MIUI8 6.6.23CN, unlocked bootloader
It started when I did an OTA from 6.6.16, then OTA failed, I tried again this time it downloaded full rom and went into my twrp but installation started automatically. Then it rebooted but the system stayed in black screen. I forced-rebooted it, then everything was fine and I was on 6.6.23. I was using the phone normally for a few hours, then around 6hr later after I upgraded, I took phone out of my bag and it was bricked. I tried everything, no fastboot, no adb, no recovery, no led, nothing on screen. MiFlash reconizes (cuz of the 9008 status) but flash fails. I event opened it up, disconnected the 3 cables from the battery and hold onto power buttons for few seconds to try to drain whatever power it has left in system. Reconnected battery but no change.
I gave up, put phone back in case and was going to ask friend to take it back to send to china for repair the next day, but then I too it out an hour before I go meet my friend and suddenly, phone led flashed red and I see on screen out-of-battery icon. I plugged it in to charge then LED flickered quickly in red for a bit then turn solid red, then turned orange. I let it charged for 10min or so, and pressed power+Vol_Down for few seconds. Lo and behold, I got the bunny on screen and went into fastboot. I was able to re-flash 6.6.23 and phone was good to go again. (but why did removing battery cables do the same thing? Maybe I didn’t leave it disconnected long enough?)
Good story until this part… then 2 days later, I wanted to test MI Talk with friend, I click on it, and phone froze. Both touch sensor light stayed on. I waited about 15 second and forced reboot. Phone vibrates once and then went into hard brick again. Exactly same situation, nothing works.
Now I am waitng for phone to discharge by itself. God knows how many days it will take. It was 96% charged. (1st time I had about 45% and too a day to discharge)
Only if I can get back into fastboot......
tkrave said:
I've been having the same problem with my MI5, 128gb running MIUI8 6.6.23CN, unlocked bootloader
It started when I did an OTA from 6.6.16, then OTA failed, I tried again this time it downloaded full rom and went into my twrp but installation started automatically. Then it rebooted but the system stayed in black screen. I forced-rebooted it, then everything was fine and I was on 6.6.23. I was using the phone normally for a few hours, then around 6hr later after I upgraded, I took phone out of my bag and it was bricked. I tried everything, no fastboot, no adb, no recovery, no led, nothing on screen. MiFlash reconizes (cuz of the 9008 status) but flash fails. I event opened it up, disconnected the 3 cables from the battery and hold onto power buttons for few seconds to try to drain whatever power it has left in system. Reconnected battery but no change.
I gave up, put phone back in case and was going to ask friend to take it back to send to china for repair the next day, but then I too it out an hour before I go meet my friend and suddenly, phone led flashed red and I see on screen out-of-battery icon. I plugged it in to charge then LED flickered quickly in red for a bit then turn solid red, then turned orange. I let it charged for 10min or so, and pressed power+Vol_Down for few seconds. Lo and behold, I got the bunny on screen and went into fastboot. I was able to re-flash 6.6.23 and phone was good to go again. (but why did removing battery cables do the same thing? Maybe I didn’t leave it disconnected long enough?)
Good story until this part… then 2 days later, I wanted to test MI Talk with friend, I click on it, and phone froze. Both touch sensor light stayed on. I waited about 15 second and forced reboot. Phone vibrates once and then went into hard brick again. Exactly same situation, nothing works.
Now I am waitng for phone to discharge by itself. God knows how many days it will take. It was 96% charged. (1st time I had about 45% and too a day to discharge)
Only if I can get back into fastboot......
Click to expand...
Click to collapse
You don't have to go into fastboot to use miflash if you have stock recovery
Sent from my MI 5 using Tapatalk
vf1 said:
You don't have to go into fastboot to use miflash if you have stock recovery
Sent from my MI 5 using Tapatalk
Click to expand...
Click to collapse
how do you flash stock recovery if you dont need to go into fastboot? now I am unable to go into recovery or fastboot as the phone does not boot at all. connecting it to PC reconizes the phone as the infamous "Qualcomm HS-USB QDLoader 9008" device.
Its been 4 days and the damn battery hasnt run out yet as I can still plug into pc and get qualcom 9008 to come up. I think I am going to send to china to get it fixed properly if I still cannot get the red flicker of low battery power to come up by tomorrow.
It has happened to me 3-4 times already. It didnt want to boot. No signs of life either. I even sent a message to the shop for sending it back..the only thing that was telling me it wasn't completely dead, was the qualcomm driver ,while on USB connection with the PC, which you are referring to as well
Here is what you could try doing. Try pressing the power button for about 30 seconds at first. If it does not boot, try bending the phone real gently back and forth (don't break it!!). Preferably, hit it gently with your palm while holding it in your other hand.( -- I know it might sound weird --) I noticed that it's shutting down while i have it in my pocket and doing some work which squeezes the phone a bit against my leg.
I came to the conclusion that some connection must become loose when some pressure is being applied to it.. Unfortunately it has to be a design flaw of the phone. Nothing random with yours or mine , in my opinion. // I have a case and tempered glass installed as well since the first minute I got it in my hands..
Sent from my MI 5 using XDA-Developers mobile app
Thanks for the tips Takkaros. I tried what you said but nothing changed (though I was a bit scared to bend it too hard). 1st time it happened to me, I had around 40-50% battery and somehow battery completely drained 24hr later so I got the red blinking low of battery light and was able to charge the phone up and go back into fastboot, which solved everything. this time it happened when I had 96% battery(which I knew cuz I was using the phone, then clicked MI Talk and phone froze, then bricked). I wish there is a way for me to force a battery drain without opening it up. I did opened it up once(on the 1st brick) and disconnected the 3 battery cables, but it was still in brick state when I put everything back.
The qualcomm 9008 driver detection was also my concern about sending back the phone. Chances are by the time my phone reaches the repair shop, battery is completely dead and they simply charge the battery then flash a stable rom and send it back to me without changing out the motherboard or whatever. Which in such case it will be faster for me to just wait a week or two and do myself, instead of shipping it to china and wasting shipping cost and probably will take 4-6 weeks.
I am not sure whats wrong with this phone. Sometimes it turns off while i have in on charge at night, with the Green led lighting. I can get into recovery mode but all the partitions are missing. I cant wipe anything and all my files are not there. If I restart the recovery 2-3 times everything comes back to normal. Maybe there is something wrong with the flash drive. If honorbuy replied to my messages i'd sent it back to them asap. This is not a reliable phone for daily use
Sent from my MI 5 using XDA-Developers mobile app
Try using mi flash. Follow the instruction
Sent from my MI 5 using Tapatalk
I am sending back the phone to china to have them "fix" it. Not sure what they will do, hopefully they either swap me a new phone or swap out the motherboard or something. I just hope they dont just boot into fastboot (after battery completely drained and system resets) and flash new rom and send it back to me.
Probably will take a month or so. Good thing i still have my old phone.
tkrave said:
I am sending back the phone to china to have them "fix" it. Not sure what they will do, hopefully they either swap me a new phone or swap out the motherboard or something. I just hope they dont just boot into fastboot (after battery completely drained and system resets) and flash new rom and send it back to me.
Probably will take a month or so. Good thing i still have my old phone.
Click to expand...
Click to collapse
This happened to me recently. I used mi flash and the global 7.2.4 stable fastboot rom to get it going again. Wouldn't work for me with with with newer versions. Think edl has been disabled on them.

Zenfone ZE554KL bricking issue

My Zenfone 4 ZE554KL is bricked and only shows on windows Qualcomm HS-USB QDLoader 9008, after I tried to debrick it from fastboot, using a firmware raw image, and putting the incorrect fastboot reboot command
"fastboot reboot emergency" and now is after I plug the usb stick it shows on windows as the QComm Com port but I tried to see guides, read everything, tried to use QFIL to check if something works and QPST
But still without success
Current phone status is a black screen and nothing else, already attempted to hold power, some few sequences with Vol Up, Vol Down still nothing.

Xiaomi mi 8 se HARD BRICKED - No response when connecting to PC

I have been using the phone for almost two years, without any problem, with a ROM from xiaomi.eu.
One day the phone suddenly went off, and I couldn't turn it on again. When I plugged it into the PC it recognized it as QLoader HS-USB 9008. I tried to flash another ROM but could not go into fastboot mode.
I decided to open it and unplug the battery, in case it was still on and without a screen, and when I reassembled it, I was able to go into fastboot mode and flash. MiFlash never gave the termination notice, and since then the phone has not responded, the computer does not recognize it, nor does it react to anything (it no longer recognizes it as QLoader HS-USB 9008). I've tried an EDL cable to do deep flash, but it doesn't work either.
I have read that there are some test points to start EDL mode, but I don't know if it will work. Do you know if it would work for this case? I also haven't managed to find a good manual to do this.
Any other idea?
Thank you very in advance.

Question Help!! Redmi 9T still stuck on EDL MODE.

Hello, i Need Help.
iam restart my phone but enter EDL MODE. idk why maybe bug miui. iam use latest miui V14.0.2.0.SJQIDXM
iam try power+up and power+down still stuck on EDL mode. iam out from EDL mode wait battery to zero. then normallycan booting.
then someday iam restart again,my phone on EDL MODE again
iam try plug PC show - qualcomm hs-usb qdloader 9008
then iam flashing fastboot "lime_global_images_V14.0.3.0.SJQMIXM_20230330.0000.00_12.0_global" after succes flash my phone still on EDL mode.. so iam press power nothing happen but iam plug on PC connected "qualcomm hs-usb qdloader 9008"
need help to solve
Autiezz said:
Hello, i Need Help.
iam restart my phone but enter EDL MODE. idk why maybe bug miui. iam use latest miui V14.0.2.0.SJQIDXM
iam try power+up and power+down still stuck on EDL mode. iam out from EDL mode wait battery to zero. then normallycan booting.
then someday iam restart again,my phone on EDL MODE again
iam try plug PC show - qualcomm hs-usb qdloader 9008
then iam flashing fastboot "lime_global_images_V14.0.3.0.SJQMIXM_20230330.0000.00_12.0_global" after succes flash my phone still on EDL mode.. so iam press power nothing happen but iam plug on PC connected "qualcomm hs-usb qdloader 9008"
need help to solve
Click to expand...
Click to collapse
If the device is not bricked, then press the three buttons for 4 seconds, and the PWR button for about 10 seconds.
SubwayChamp said:
If the device is not bricked, then press the three buttons for 4 seconds, and the PWR button for about 10 seconds.
Click to expand...
Click to collapse
btw if battery drained to 0 normal again, then carhger normal again can booting to rom and play game, etc. but if iam click restart/i want restart phone after restart not wakeup but to edl mode "hs-usb qdloader9008". my phone never like this never dropped and wet

Categories

Resources