I have a D5803 that came back from being serviced. The touchscreen went bad, so the whole assembly (screen + sensor) was replaced.
Since you have to almost completely disassembly the phone to get to the screen, I suspect something went wrong during the repair.
The screen is flickering at random. By flickering, imagine a bad fluorescent lamp: you can clearly see the brightness varying vary fast, causing a flicker effect. Also, imagina a CRT screen. The flicker stops when you refresh the screen, like cycling through the home screens of your phone.
The guy who repaired it said it is a bad resistor that controls the current going to the panel's backlight. His excuse is that the board is very thin and fragile and that something might happened during the repair service. He also said that if he tries to do something else, the problem might get worse/something else might break. I suspect the screen installed is not OEM and is of bad quality. Sometimes the screen keeps autopressing as if someone was actually touching the screen, but not. Wiping the screen down on soft clothes (cleaning it) solves the problem. The screen probably doesn't have an oleophobic coating.
So, my question is: Is this guy right or is he lying (trying to push me ****ty parts/service)? How to know?
Also, is it possible to have a slightly smaller sized screen part? Because it feels that the screen area has decreased a bit (bezel increased somewhat). But since I do not use this phone since almost two years ago, I might be imagining things.
Related
I just got a tilt about a week ago and ive noticed that in the middle of the screen there seems to be a purple greenish tint when put against incandescent light. The size of said glint varies in size but i'm unable to see what changes the size. Not sure if its heat or pressure or something. The touch screen works perfectly its just really annoying to always see such an annoying glint.
An interesting discovery is that when i press all four corners of the screen it disappears and when i press in the middle of the little square it seems to spread out. I feel like theres some kind of material or something in the touch screen that is causing this due to pressure. I keep it in a hard case in my pocket so the screen isnt pressed on inadvertently.
I've searched the forum for any answers but i havent seen anything about it. Any response or help would be greatly appreciated. I'll try to get a picture of it up asap but i left my camera at a friends house and dont know when im getting it back...thanks in advanced
~sayazs
Do you see the same "annoying glint" under neon light (not day / sunlight)?
Lots of NOKIA and SONY ERICSSON phones for example get this screen recolorization under direct sunlight - this has nothing to do with the screen being defective but with the plastic above the screen which breaks the light and shows you this colored spots. If you can't see the same spot under direct neon light then this might be the cause.
It is normal that you get color changes while pressing the screen in. First of, you press / bent the protecting plastic and the liquid within the screen which causes the incoming light to break in a different angle, therefore the color changes. (BTW: you shouldn't do that too often, it can cause permanent stains on your screen!).
There sure is the possibility that your screen gets pressure from underneath due bad assembling! If you're still under warranty, try to get a replacement.
yeah you cant see it in day light. but i feel as though there is constant pressure on the screen between the plastic and liquid since the spot is always there and doesnt really go away (unless of course in daylight).
well im thinking im going to go back for a replacement. thanks for the quick answer!
Recently, I noticed the is a strange circle in the middle of the screen. When the screen backlight is off, it appears as a black circle. When the screen backlight is on, it appears as red/yellow/black ring. Somtimes it went away by itself, and other time I have to "wipe" it away with finger force.
Anyone know what is wrong?
2 questions
1) Have you tried removing the screen protection just to see whether its on the screen protection or on the main lcd screen
2) did you ever exposed lcd it to high electromagnetic waves??
1. I didn't remove the screen protector as I believe it's beneath the LCD film.
2. I don't think it has been exposed to any electromagnetic waves, as it appears after I pulled it out from my pocket.
I've had it too but it's gone now
I had the exact same problem a few weeks ago. The place I stayed was not well ventilated and I THINK it caused some water condensation to occur between the digitizer and lcd screen. I slept in an air-conditioned room the next day and it was gone!
My deduction is that you need a cool or cold environment for the stain to evaporate.
The same problem arises again, and this time it has been a couple days but it still did not go away.
It looks almost like a burn mark.
You may have a defective digitizer.
Found another thread talking about this:
http://forum.xda-developers.com/showthread.php?t=439410
This is the so-called 'Newton ring' in optics/Physics. It means that in that area, the thickness of LCD is slightly thicker/thinner than rest of the area. This is normally due to stress at that point. It is annoying but if there are no repeated color rings, like red/yellow/blue/red/yellow/blue, it should be fine. If you have alot of repeated color rings, the LCD may approach its life end.
frank.lui said:
This is the so-called 'Newton ring' in optics/Physics. It means that in that area, the thickness of LCD is slightly thicker/thinner than rest of the area. This is normally due to stress at that point. It is annoying but if there are no repeated color rings, like red/yellow/blue/red/yellow/blue, it should be fine. If you have alot of repeated color rings, the LCD may approach its life end.
Click to expand...
Click to collapse
Thanks for the info. When you said it should be fine, do you mean it will disappear, or it just won't affect usability?
It may disappear if the stress is released, e.g., you push the area a bit or you put it into different temperature environment. But I doubt it will disappear for ever. It was not there in the first place then it came. This means some sort of stress/pressure built up there. It should not affect your daily use a lot. It is just a visual effect. But if it gets worse, the colour rings will become very dense and sharp. It will affect you visual. I had a phone pinged on LCD sometime ago. It had similar rings like yours. But it was so dense I could not see any thing behind it. I had to change it for £35.
Also I looked at another previous comment about the humidity. It could give you the same effect. Maybe you can bake your phone a bit?
Since day one, I've had touchscreen issues. When the charger is plugged in, the keyboard is unusable. One touch triggers keys all over the place faster than I could ever touch the screen. Unplugging the charger fixes that issue.
After a while, phantom presses start happening. If an app supports multitouch zoom, it becomes impossible to scroll instead of zooming. Keeping the screen clean seems to delay the problem from happening. If the problem presents, just cleaning the screen won't help. I have to turn the display off and back on for any effect. I've heard putting on a screen protector helps with this issue, but I haven't had a chance get one. If the screen protector just masks the issue, that doesn't seem like a good fix.
Should I try to get a replacement Nook Color now that doesn't have these issues or should I wait until the last month of my warranty to see if I can get more developed hardware? There doesn't seem to be a consensus if these issues are hardware or software.
scratchfury said:
Since day one, I've had touchscreen issues. When the charger is plugged in, the keyboard is unusable. One touch triggers keys all over the place faster than I could ever touch the screen. Unplugging the charger fixes that issue.
After a while, phantom presses start happening. If an app supports multitouch zoom, it becomes impossible to scroll instead of zooming. Keeping the screen clean seems to delay the problem from happening. If the problem presents, just cleaning the screen won't help. I have to turn the display off and back on for any effect. I've heard putting on a screen protector helps with this issue, but I haven't had a chance get one. If the screen protector just masks the issue, that doesn't seem like a good fix.
Should I try to get a replacement Nook Color now that doesn't have these issues or should I wait until the last month of my warranty to see if I can get more developed hardware? There doesn't seem to be a consensus if these issues are hardware or software.
Click to expand...
Click to collapse
That must be frustrating. Mine does not behave this way at all (though I've only had it for 4 days). If you bought it in the store, I'd exchange it. If you bought it via the BN ebay store, I'd try the screen protector first as I hear it's quite an ordeal returning it via ebay.
This us a very common issue. It has something to do with sensitivity of the screen increasing greatly when the unitbis charging or the screen brightness is way up. I just chage mine at night and don't worry about it.
I was having a lot of problems with phantom touches -- I even replaced my 2nd NC just to get another one that had the same issue. I ended up putting on a B&N anti-glare screen protector and haven't witnessed any phantom touches since then.
Edit: I actually meant to post this in the other phantom touches thread. ;/
Happens a lot to me even while unplugged. Known issue. Until I pick up a B&N screen protector I find locking the device and a quick wiping of the screen with a microfiber or any soft cloth (my shirt works in a pinch) removes moisture and oil build-up that is causing the uber-sensitive digitizer to register phantom touches.
Sent from my Nook Color using Tapatalk
So my phone cracked up today(rip) while I was doing some gym exercises. The phone fell from like 1.5 metter or so and the screen cracked.
The problem is that screen won't turn on, even when the phone looks like it works. I tried to furce shut down and turn it on and back and recents buttons work, but screen while stay black. What should I do? I will replace the screen but I'm not sure why screen won't show up, maybe something got disconected with the fell? Does anyone has any type of experience with this?
Jaizu said:
So my phone cracked up today(rip) while I was doing some gym exercises. The phone fell from like 1.5 metter or so and the screen cracked.
The problem is that screen won't turn on, even when the phone looks like it works. I tried to furce shut down and turn it on and back and recents buttons work, but screen while stay black. What should I do? I will replace the screen but I'm not sure why screen won't show up, maybe something got disconected with the fell? Does anyone has any type of experience with this?
Click to expand...
Click to collapse
So, your screen is broken, and you need to have it repaired, what is the problem? Some parts still working?
Just get it fixed...
Verstuurd vanaf mijn SHIELD Tablet K1 met Tapatalk
I really don't know why you asked this question, but I always try to be helpful. Since you did drop it, and from such a height (do you like keep your phone in your pocket while doing pull-ups? Mine's always in my bag and I use BT earphones).
Since your screen is cracked, and that impact could've damaged your phone in many ways.
1. You could've damaged your digitizer, which is a screen replacement situation
2. You bent a cable from your screen to something else, and that may be the issue, still would need to replace the screen.
Your buttons working have no relativity with the screen not working, it works with other hardware not interacting with your screen.
Don't go for third-party screen replacements that "fixes your digitizer seperate from the touch", it mostly doesn't work, and it'll be a waste of money, if you bought it from OP Store, just RMA it, or if you bought it from a seller in your country, just order the screen off eBay, and have it fixed. Your shop will most likely replace it with a non original screen, which will be horrible.
Cheers!
I think he is confused about the glass versus the AMOLED panel. A lot of times, you see folks with broken glass, but the screen still works (still displays graphics) and he is wondering why that isn't the case. At least, that is how I'm interpreting the question.
The answer is that the "screen" is composed of layers. The top layer is the glass (which for Super AMOLED also incorporates the touch panel or digitizer) and below that is the AMOLED which actually displays the graphics.
Since the glass is broken, and the AMOLED is not working, it's possible (or even likely) that the AMOLED was also broken in the impact. Yes, it's also possible that a connector has come loose. But from what I'm reading, it's actually common for the AMOLED to break before Gorilla Glass does: http://www.gophermods.com/amoled-vs-lcd-tale-two-screens/
A lot of times when you see folks with glass broken, but everything (touch and graphics) still work, it may be with LCD screens; which are supposedly more durable (more possible for glass to break before the LCD).
I have installed Xposed and Sensor Disabler and have disabled the proximity sensor since I was guessing that it was that causing the error. But screen still goes black the second I call and stays black. Only way I can get it on is if called person hangs up or if I double tap the screen on button many times and then if I'm very lucky the screen turns on but easily turns black again very quickly.. What am I missing here?
old issue. Look for proximity sensor issue / failure. Happens with aftermarket screens, but also because of the ****ty sandwhich construction of the phone. There is about one mm friction possible for the frame, which leads to the slowly letting loose of the screen. Have a Z3 compact like that. tried glueing (B 7000 glue) but still. I can see the light inbetween frame and screen. Only a hardcover can possibly maybe prevent this screen from dis-attaching itsself from the frame. I rooted mine as to try disabling the proximity sensor, but I also failed doing that. I actually bought a Z1 compact again. Easy to fix. Thats why I thought the Z3 compact would be an upgrade. Well its not. Its build-quality is a nightmare. And repair also sucks. I even bought a screen plus frame new, and after installation I already saw space between the frame and the screen. Can't sell mine. Its useless. Stay away from this model. very, very bad.