Database Develop

my problem

hi
my problem is
I tried to downgrade my phone
android 6 to 5
My phone was incomplete downgrade
And now when turned off and turned on
Stuck on the
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Please tell me what is the alternative
No option is not enabled
no recovery
no Emergency Updates
only fastboot mod

the fastboot mode is worked

rezaghaedamini said:
the fastboot mode is worked
Click to expand...
Click to collapse
Take it to Huawei customer service center. I lost one of my phones coz it had the same problem. Tried everything but couldn't revive it.
Took it to a shop to repair and he messed it up.

Connect to pc or laptop and open command prompt to adb folder and type fastboot devices if devices detected then we proceed http://forum.xda-developers.com/general/general/guide-flash-variant-version-firmware-t3506404.

Krish93 said:
Connect to pc or laptop and open command prompt to adb folder and type fastboot devices if devices detected then we proceed http://forum.xda-developers.com/general/general/guide-flash-variant-version-firmware-t3506404.
Click to expand...
Click to collapse
My bad, should have asked him to do this first. Mine was error 3 and wasn't revivable.
This error is different. Thanks for the help.

You need to unlock your device.
https://www.gizdev.com/install-twrp-3-0-root-honor-4x-emui-4-0/
1-unlock your device
2-run bootloader
3-install twrp
4-extract the honor firmware
http://forum.xda-developers.com/honor-4x/how-to/roll-to-emui-cm13-honor-4x-che1-l04-t3507998
5-follow the instructions as above link.

Krish93 said:
Connect to pc or laptop and open command prompt to adb folder and type fastboot devices if devices detected then we proceed http://forum.xda-developers.com/general/general/guide-flash-variant-version-firmware-t3506404.
Click to expand...
Click to collapse
i did
My phone did not change

dopserver said:
You need to unlock your device.
https://www.gizdev.com/install-twrp-3-0-root-honor-4x-emui-4-0/
1-unlock your device
2-run bootloader
3-install twrp
4-extract the honor firmware
http://forum.xda-developers.com/honor-4x/how-to/roll-to-emui-cm13-honor-4x-che1-l04-t3507998
5-follow the instructions as above link.
Click to expand...
Click to collapse
my phone is unlocked
and All these things did
Did not alter

rezaghaedamini said:
my phone is unlocked
and All these things did
Did not alter
Click to expand...
Click to collapse
Connect your phone to PC and keep device manager opened and see if device manager registers your phone.
Report back please...

muradulislam said:
Connect your phone to PC and keep device manager opened and see if device manager registers your phone.
Report back please...
Click to expand...
Click to collapse
MY English is not good please tell me What do you mean
device manager to phone
or to pc

rezaghaedamini said:
MY English is not good please tell me What do you mean
device manager to phone
or to pc
Click to expand...
Click to collapse
Keep your PC device manager open and connect your phone to PC, does it register as a new device...

not big deal ,
Do The following
Install Fastboot files .
Download TWRP .
Connect Ur Device with Fastboot ,
Flash Ur TWRP Throw Fastboot .
Boot To TWRP
FLASH STOCK img Files One By one
This Step Not Recommended but also :
Throw Fast-boot Flash UR Stock .img files .

Romiui said:
not big deal ,
Do The following
Install Fastboot files .
Download TWRP .
Connect Ur Device with Fastboot ,
Flash Ur TWRP Throw Fastboot .
Boot To TWRP
FLASH STOCK img Files One By one
This Step Not Recommended but also :
Throw Fast-boot Flash UR Stock .img files .
Click to expand...
Click to collapse
tnk not work

rezaghaedamini said:
tnk not work
Click to expand...
Click to collapse
it should otherwise there is an wrong step u did ! .

rezaghaedamini said:
tnk not work
Click to expand...
Click to collapse
If your PC does not make a sound when you connect your phone to it then you have to first install drivers.
I am sure that is the case here, your PC is not recognizing your phone.

muradulislam said:
If your PC does not make a sound when you connect your phone to it then you have to first install drivers.
I am sure that is the case here, your PC is not recognizing your phone.
Click to expand...
Click to collapse
I have installed drivers
And when I connect the phone to the sound system
Only through the Fast Boot

rezaghaedamini said:
I have installed drivers
And when I connect the phone to the sound system
Only through the Fast Boot
Click to expand...
Click to collapse
So fastboot is working... Do you have an unlocked bootloader?
Fastboot screen is simple or with red error message?

muradulislam said:
So fastboot is working... Do you have an unlocked bootloader?
Fastboot screen is simple or with red error message?
Click to expand...
Click to collapse
yes i am bootloader unlocked
Both options
Red and simple
i can Write files via Fast Boot
and write android 4 5 6
5 file
boot
system
recovery
cust
userdata
and not work
and write twrp recovery
and not work

rezaghaedamini said:
yes i am bootloader unlocked
Both options
Red and simple
i can Write files via Fast Boot
and write android 4 5 6
5 file
boot
system
recovery
cust
userdata
and not work
and write twrp recovery
and not work
Click to expand...
Click to collapse
Make a dload folder in SD card And copy update.app of the latest firmware to it.
Then, flash only recovery and boot of the latest firmware for your phone. (Extracted from update.app which you copied to SD)
After flashing above image files, type
Fastboot reboot
Quickly disconnect from pc and press and hold power + vol up + vol down until screen turns on. Let go of power but keep other two pressed for five, six sec more.
Lemme know how it works.

if stock wont work then try custom rom , install custom recovery and install custom rom .

[how-to] erase partition table of redmi 2/prime/2a....

I AM NOT RESPONSIBLE FOR BRICKED DEVICES, DEAD SD CARDS,
THERMONUCLEAR WAR.YOU ARE CHOOSING TO MAKE THESE MODIFICATIONS, AND IF
YOU POINT THE FINGER AT ME FOR MESSING UP YOUR DEVICE, I WILL LAUGH AT YOU. HARD. A LOT.
THIS GUIDE WILL HELP YOU TO ERASE PARTITION TABLE AND RESTORE STOCK PARTITION TABLE OF REDMI 2.
IF YOU MESSED UP WITH YOUR PHONE PARTITION TABLE, OR SOMETHING ELSE.
THIS WILL REWRITE THE WHOLE PARTITION TABLE FOR YOUR PHONE RATHER SIMPLY FLASHING THE PARTITIONS.
REQUIRMENTS:
1.) REDMI 2 (ANY VARIANT) CHARGED ABOVE 75%.
2.) A WINDOWS PC.
3.) MI FLASH TOOL AND GET IT INSTALLED. ---> http://en.miui.com/thread-339517-1-1.html
ALTERNATE MI FLASH TOOL IF YOUR DEVICE IS NOT DETECTED AFTER RUNNING .BAT FILE--> https://1drv.ms/u/s!AjRyVY8i_bd1nURHfzNelaEUosue
4.) MI FASTBOOT ROM DOWNLOAD AND EXTRACT IT. ---> http://en.miui.com/forum.php?mod=viewthread&tid=439829
(I RECOMMEND 1 GB VARIANTS OWNER TO DOWNLOAD REDMI 2 PRIME FASTBOOT ROM.)
5.) ERASE_PARTITION_TABLE.zip FROM ATTACHMENTS.
PROCEDURE:
1.) DOWNLOAD AND EXTRACT ERASE_PARTITION_TABLE.zip
2.) CONNECT YOUR DEVICE TO PC IN FASTBOOT MODE.
3.) RUN .BAT FILE FROM ERASE_PARTITION_TABLE.zip
4.) A DIALOG FROM WINDOWS WILL APPEAR TO FORMAT DRIVE. JUST CLICK CANCEL.
5.)YOU PHONE SCREEN WILL BE BLACK. DONT PULL OUT USB CABLE.
6.)RUN MI FLASH TOOL AND FLASH DOWNLOADED REDMI 2 PRIME FASTBOOT ROM USING FLASH_ALL.BAT
7.) AFTER 5-10 MINS YOUR PHONE WILL BOOT INTO MIUI ROM.
8.) TO USE CUSTOM ROM FLASH APPROPRIATE CUSTOM RECCOVERY AND ROM.
HOPE THIS FIXES ALL ISSEUES RELATED TO MODEL NUMBER CHANGE,VO-LTE, etc,etc,etc.

Simply reserved.

It hard bricked my phone, not showing in miflash and can't go into recovery or fastboot mode. Only showing as Local Disk G in pc

Bhargab Deka said:
It hard bricked my phone, not showing in miflash and can't go into recovery or fastboot mode. Only showing as Local Disk G in pc
Click to expand...
Click to collapse
Does it show as HS Q loader something?

aashishdamrait said:
Does it show as HS Q loader something?
Click to expand...
Click to collapse
Its showing qualcomm hs usb diagnostics 9006 (com11) in device manager -ports

it happened here too, what should I do????
---------- Post added at 16:46 ---------- Previous post was at 16:17 ----------
@aashishdamrait I was scared as **** bro, my device was black and 23 disk partitions opened in the windows, but I managed to revive the device by using the other mi flash, that was scary as hell

@TecnoTailsPlays
Now, I hope phone is working fine?

aashishdamrait said:
@TecnoTailsPlays
Now, I hope phone is working fine?
Click to expand...
Click to collapse
Yep, back to normal state

@TecnoTailsPlays
Did this fixed random reboots for you?

aashishdamrait said:
@TecnoTailsPlays
Did this fixed random reboots for you?
Click to expand...
Click to collapse
Nope

ASK a senior member
I have to problem with flashing xiaomi redmi 2 prime HM2014813 as a notifcation unspecified error( 0×80004005) failed ( remote : failed to write partition)
Please help me a lord
How can it fixed flashing xiaomi redmi 2 prime hm2014813?
Sent from my SM-J500G using Tapatalk

IAM_COOL49 said:
ASK a senior member
I have to problem with flashing xiaomi redmi 2 prime HM2014813 as a notifcation unspecified error( 0×80004005) failed ( remote : failed to write partition)
Click to expand...
Click to collapse
Kindly Send the Screenshots.
do tell me about the Mi flash tool you are using , rom and and.

aashishdamrait said:
Kindly Send the Screenshots.
do tell me about the Mi flash tool you are using , rom and and.
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Run "erase_partition_table.bat" again.
do verify you have selected all the files under browse category like patch.xml.

Okay i'm trying flash using erase partition a lord

I messed up with my mi3w
can I use it on my mi3w? Will it work ?

it works. thanks for the guide I have Redmi 2 Pro wt88047.

aashishdamrait said:
Run "erase_partition_table.bat" again.
do verify you have selected all the files under browse category like patch.xml.
Click to expand...
Click to collapse
Hey, I have a problem with my Redmi 2 version 2014813 and I can only access TWRP, whenever I try to flash any compatible ROM I get the errors I attached in the picture.
Also when I try to flash via fastboot it fails --> fastboot flash partition gpt_both0.bin --> FAILED to write partition
Any idea how to try to fix this? You think your scrip for the partition table can help?

Adi59 said:
Hey, I have a problem with my Redmi 2 version 2014813 and I can only access TWRP, whenever I try to flash any compatible ROM I get the errors I attached in the picture.
Also when I try to flash via fastboot it fails --> fastboot flash partition gpt_both0.bin --> FAILED to write partition
Any idea how to try to fix this? You think your scrip for the partition table can help?
Click to expand...
Click to collapse
Same here. Did you find a solution ?

oferyuval said:
Same here. Did you find a solution ?
Click to expand...
Click to collapse
I tried many different ways to flash any ROM into it without any success. I read somewhere in the miui eu forums that the redmi2 pro had a stupid software update that was not meant for one type of emmc and broke it. Someone who contacted the Chinese support got his/her phone swapped or money back.
I still have the phone in same condition hoping to manage one day to replace the emmc chip. I think that will fix the issue.
EDIT: original post:
"Bad news - Redmi 2 the series 2014813 has faulty NAND memory. After 1 to 1.5 year of operation the memory dies. First warning is "App stopped working" message. Then the phone dies and after rebooting you see just the Mi logo.
Flashing new ROM usualy fixes this problem and phone works for 1-2 months without problems. Then the fault apears again and it is end for the phone. You can enter fastboot mode, TWRP, but there is no was how to write any data to internal memory. Fastboot, TWRP nor MiFlash do not work because this is a hardware problem. The only way is replacing NAND memory, but this is extremely complicated task." source: http://en.miui.com/thread-268891-3-1.html
EDIT2: check this thread also: https://forum.xda-developers.com/android/help/how-to-boot-sd-card-qmobile-z8-bricked-t3712171

Lenovo a7000-a won't boot & can't enter to recovery

Hello, i have spartphone Lenovo a7000-a, with TWRP Recovery and custom rom "Resurrection remix". When i wanted to update rom to newer version, mobile stuck on booting, and he falled to endless restarting. I can't enter to recovery, i can't do anything with mobile.
i used smart phone flash tool, with stock rom, but tool can't find my mobile.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
- Mobile stuck on this screen, and sometimes restarts and again stuck on this screen.
i hope that anybody can help me, I don't know what else to do. Many thanks for helping

Firstly, install mediatek vcom drivers, don't use the add hardware option in device manager. Right click proper .inf file in explorer and click install, click continue with the installation on the warning prompt. If you are on Windows 8/8.1/10 search for how to install unsigned drivers and do the same. Then download the twrp package from this forum. It should have boot.img and recovery.img . Install with sp flash tool, select the scatter file from the folder and make sure both boot and recovery are ticked. Go to options ->download and make sure both checksums are ticked. SP flash tool dropdown menu should show download only. Click download/start/whatever and connect powered off phone with a good data cable. Flash should start and it'll finish soon. Now disconnect data cable, press both volume buttons firmly and press power button. Don't let go unless you see a Lenovo logo. It should boot into TWRP. You custom ROM may not boot but now you have TWRP.
Edit: Here is the TWRP link http://forum.xda-developers.com/lenovo-a7000/development/twrp-recovery-lenovo-a7000-mm-t3358436. Do NOT untick boot.img. If you can't get to recovery you must flash boot.img as well

fingerwarrior said:
Firstly, install mediatek vcom drivers, don't use the add hardware option in device manager. Right click proper .inf file in explorer and click install, click continue with the installation on the warning prompt. If you are on Windows 8/8.1/10 search for how to install unsigned drivers and do the same. Then download the twrp package from this forum. It should have boot.img and recovery.img . Install with sp flash tool, select the scatter file from the folder and make sure both boot and recovery are ticked. Go to options ->download and make sure both checksums are ticked. SP flash tool dropdown menu should show download only. Click download/start/whatever and connect powered off phone with a good data cable. Flash should start and it'll finish soon. Now disconnect data cable, press both volume buttons firmly and press power button. Don't let go unless you see a Lenovo logo. It should boot into TWRP. You custom ROM may not boot but now you have TWRP.
Edit: Here is the TWRP link http://forum.xda-developers.com/lenovo-a7000/development/twrp-recovery-lenovo-a7000-mm-t3358436. Do NOT untick boot.img. If you can't get to recovery you must flash boot.img as well
Click to expand...
Click to collapse
Hi i tried your way, but i got error error.
here is how i proceeded:
where i made a mistake?

There are two possibilities here,
1. Your phone is not really A7000, rather it is A7000 plus or turbo
2. The installed partitions are different enough that SP Flash tool refuses to flash it.
You can try to flash the stock rom S228 if you are sure it is lenovo A7000. If it again throws out same error and you are perfectly SURE it is lenovo a7000, you can try to format first and then flash the rom, although it is not recommended.

fingerwarrior said:
There are two possibilities here,
1. Your phone is not really A7000, rather it is A7000 plus or turbo
2. The installed partitions are different enough that SP Flash tool refuses to flash it.
You can try to flash the stock rom S228 if you are sure it is lenovo A7000. If it again throws out same error and you are perfectly SURE it is lenovo a7000, you can try to format first and then flash the rom, although it is not recommended.
Click to expand...
Click to collapse
1.) I have lenovo a7000-a
2.) I also tried a7000-a stock firmware, but when i downloaded it via SPFlashTool, downloading stuck at Download DA 100% and then i get timeout.
EDIT:
it seems that, mobile is soft-bricked, without recovery.
But i can enter to META mode & FACTORY mode. I can Flash (via SPFlashTool) but it stucks at Download DA 100% (on red line).
Downloading stuck on this screen and then i get Timeout.

Powering said:
1.) I have lenovo a7000-a
2.) I also tried a7000-a stock firmware, but when i downloaded it via SPFlashTool, downloading stuck at Download DA 100% and then i get timeout.
EDIT:
it seems that, mobile is soft-bricked, without recovery.
But i can enter to META mode & FACTORY mode. I can Flash (via SPFlashTool) but it stucks at Download DA 100% (on red line).
Downloading stuck on this screen and then i get Timeout.
Click to expand...
Click to collapse
I also have Lenovo a7000-a. Tried flashing stocks roms (as per other thread) as stock ROM but still gets grey screen and white lines.
What ROM build number are you using. Can you share the link?
I just want to revert back to original (stock) ROM and make it work again.
Sent from my Pixel XL using Tapatalk
---------- Post added at 01:03 PM ---------- Previous post was at 01:02 PM ----------
fingerwarrior said:
There are two possibilities here,
1. Your phone is not really A7000, rather it is A7000 plus or turbo
2. The installed partitions are different enough that SP Flash tool refuses to flash it.
You can try to flash the stock rom S228 if you are sure it is lenovo A7000. If it again throws out same error and you are perfectly SURE it is lenovo a7000, you can try to format first and then flash the rom, although it is not recommended.
Click to expand...
Click to collapse
What's the stock ROM for Lenovo a7000-a? I have grey screen and white lines.
Sent from my Pixel XL using Tapatalk

Bro i advise you to follow the below link and download the stock rom again and flash it again by spflashtool
And follow every step as mentioned in the below link
http://forum.xda-developers.com/lenovo-a7000/development/flashing-stock-rom-via-sp-flash-t3364235

PrashantRana said:
Bro i advise you to follow the below link and download the stock rom again and flash it again by spflashtool
And follow every step as mentioned in the below link
http://forum.xda-developers.com/lenovo-a7000/development/flashing-stock-rom-via-sp-flash-t3364235
Click to expand...
Click to collapse
I tried this, but process stucks at "Download flash 0%" (yellow bar)

Powering said:
I tried this, but process stucks at "Download flash 0%" (yellow bar)
Click to expand...
Click to collapse
as your download is not starting so it may be possible that driver are not correctly installed

[GUIDE] Unbrick your device or recover from bootloop

Assalamu alaikum people,
Those on the telegram group know that I bugged you a lot about needing data partition. Because of my experience with unbricking and recovering the device, I can tell you a sureshot method that works to restore the device. Do not use this method if your device already works. There seems to be a lot of files inside the data partition which are necessary for the stock ROM to work. This method asks you to wipe data partition and so system update will not work. This should be a last resort. .
Many people seem to have come to the situation where they are in fastboot, and it says frp locked, so they cannot flash new twrp. And the system seems to be in bootloop and it does not work. What to do from there?
1. Download this file ->https://www.androidfilehost.com/?fid=673956719939832337.
2. In your SDCard, create a folder called TWRP and inside it, create a folder called BACKUPS (all in capitals). Inside this, create a folder called 7xtwrpbackup (small letters) and paste the contents of the zip that you have downloaded into this.
3. Boot to twrp in your device and go to restore. There you should see a folder 7xtwrpbackup. If you select it, you will get a checkbox below with recovery_ramdisk like this
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
4. Select Yes and after restore complete, go back and select reboot and reboot to recovery.
5. Now, the new twrp will boot. In the new twrp, I want you to first go to wipe -> advanced wipe -> select dalvik/art cache, cache, data, internal storage and system.
6. Come back once again and select wipe, and this time, select format data. It will ask you to type yes. After that is done, come back once again.
7. Now select install and in that, install the openkirin RR image from telegram group or here -> https://forum.xda-developers.com/honor-view-10/development/rom-t3753555 (This step is optional because openkirin RR has a greater chance of booting than stock ROM. You can skip this step and directly boot stock)
8. Your system must boot now. If it boots, then all partitions are good. You can boot stock.
9. You can now can download stock from my post here and repeat from step 5-> https://forum.xda-developers.com/9-lite/development/stock-img-unlock-indian-version-t3767569
If this does not work, then look at the second method in the next post

Second method
If your first method does not work, then you can try this second method. Make sure you have enough data left in your internet connection (1.8 GB ish) before starting the process. Please note that this method will lock your bootloader, install stock recovery, flash the stock system and boot your phone. Of course, even if it relocks the bootloader, you can still unlock it using your code.
1. Download the zip
https://www.androidfilehost.com/?fid=746010030569970895
2. Extract it into sdcard directly (i.e. extract it to the root folder of your sdcard)
3. Make sure you have enough battery left (atleast 15%). Power off your phone. Now, press and hold vol up + Vol down + power buttons until the honor logo comes. Then, you can release all the keys. The system will go into emui recovery and restore your phone.
You will have stock phone at the end of the process.
Note:-If you still have bootloop at Honor logo, then power off the phone. Hold vol up + power button until the honor logo comes. It will boot into stock recovery. From there, you can do a factory reset and erase cache partition. Then the phone will definitely boot up.

Bricked my device Twrp doesn't work
Hello, I have bricked my honor 9 lite AL10(Indian Version). I have formatted my vender directory through Twrp by mistake now my device shows erecovery and reboots. Fastboot is working fine and FRP and Devices both shows unlocked means I can flash through fastboot. I don't want to lose my internal memory data.
Help me to unbrick my device !! :crying:

Oushal kDee said:
Hello, I have bricked my honor 9 lite AL10(Indian Version). I have formatted my vender directory through Twrp by mistake now my device shows erecovery and reboots. Fastboot is working fine and FRP and Devices both shows unlocked means I can flash through fastboot. I don't want to lose my internal memory data.
Help me to unbrick my device !! :crying:
Click to expand...
Click to collapse
Download vendor partition from here https://forum.xda-developers.com/9-lite/development/stock-img-unlock-indian-version-t3767569

Hello i am siddharth, i have relocked my oem by fastboot oem relock -------- after that yes/no option came i click on yes. It starts factory formatting after completion of formatting when the phone starts its showing your device has failed verification and got stuck in it. When i press reboot option it will directly comes to erecovery mode wher the option came to download new recovery when i connect my phone with wifi it starts searching for some time after that system update failed.
When i starts mobile directly to fastboot mode by pressing volume down button and power button the white screen with android comes appear i.e fastboot mode screen. In that screen in green colour i found that
Phone Relock
FRP lock
When ever i m trying to find the device in fastboot mode by typing fastboot devices my device showing there but no other command is working such as fastboot oem unlock -------, fastboot flash system system.img, all the time it comes Failed.
I have downloaded many UPDATE.APP and tried to load that by dload method but every time after 5% it come Failed to install.
I have downloaded UPDATE.APP form ur given link also. This is only the image in which my phone comes upto 23% install after dat failed.
Nothing working for me. Kindly help me.
Mail me if there is any solution @
[email protected]

i have tried first method it failed and says 'no partition selected for restore'
and their is no option to select partition what should i do plz help

None of the method worked for me my device still bootloops no matter what system.img or rom zip file i flash. The emui recovery method didn't work for me as it loaded up to 5% and then failed instantly. Please help me unbrick my 9 lite bro. Could you provide me the boot.img? i think my phone got bricked because i tried to i install magisk on treble rom (i guess?). But anyway PLEASE HELP ME (

Try extracting kernel.img from an update and flash that. It fixed it for me.

hi twrp is bootlooping as well
cant access
---------- Post added at 07:15 PM ---------- Previous post was at 06:52 PM ----------
hey i used the twrp from the link made a backup restored it now a get bootloop cant get into twrp it goes in ti it then it fcs then am back to bootloader unlocked warning

hi anyone got custom.img and userdata.img from this LLDL31C432B130 800130 a need to restore my device

Same Problem
[email protected] said:
i have tried first method it failed and says 'no partition selected for restore'
and their is no option to select partition what should i do plz help
Click to expand...
Click to collapse
Even I'm facing the same problem, if anyone has solution plz help.
---------- Post added at 10:15 AM ---------- Previous post was at 10:10 AM ----------
[email protected] said:
i have tried first method it failed and says 'no partition selected for restore'
and their is no option to select partition what should i do plz help
Click to expand...
Click to collapse
Even I'm facing the same problem.

mine goes to 5% doesnt do anything and then it fails

aveemashfaq said:
If your first method does not work, then you can try this second method. Make sure you have enough data left in your internet connection (1.8 GB ish) before starting the process. Please note that this method will lock your bootloader, install stock recovery, flash the stock system and boot your phone. Of course, even if it relocks the bootloader, you can still unlock it using your code.
1. Download the zip
https://www.androidfilehost.com/?fid=746010030569970895
2. Extract it into sdcard directly (i.e. extract it to the root folder of your sdcard)
3. Make sure you have enough battery left (atleast 15%). Power off your phone. Now, press and hold vol up + Vol down + power buttons until the honor logo comes. Then, you can release all the keys. The system will go into emui recovery and restore your phone.
You will have stock phone at the end of the process.
Note:-If you still have bootloop at Honor logo, then power off the phone. Hold vol up + power button until the honor logo comes. It will boot into stock recovery. From there, you can do a factory reset and erase cache partition. Then the phone will definitely boot up.
Click to expand...
Click to collapse
But this is for L31
---------- Post added at 08:06 AM ---------- Previous post was at 08:05 AM ----------
My phone's frp and bootloader locked,and phone is booting to erecovery,what to do

need help with LLD-AL10C675 indian version
I have flashed a cutom treble rom phh-treble to be specific,used it for couple of days and then tried instaling the magisk from magiskmanager and after its done when i reboot it shows error mode with message Func no:10(boot img ) and func no:2 , i can boot into fastboot mode both frp and phone unlocked ,can some please help me to get back my phone into a usable condition thank you

sunny_deed said:
I have flashed a cutom treble rom phh-treble to be specific,used it for couple of days and then tried instaling the magisk from magiskmanager and after its done when i reboot it shows error mode with message Func no:10(boot img ) and func no:2 , i can boot into fastboot mode both frp and phone unlocked ,can some please help me to get back my phone into a usable condition thank you
Click to expand...
Click to collapse
To help you a full firmware is required and that's not available for (India c675) yet!
Before any modification to system you should have a full firmware in hand.

BS4388 said:
To help you a full firmware is required and that's not available for (India c675) yet!
Before any modification to system you should have a full firmware in hand.
Click to expand...
Click to collapse
yea that was a pretty big mistake i made without looking for it, i have been told by someone that we can pull out all the require d imgs from a phone in good working condition, i asked in the hopes that someone would be generous enough to do that for me , thank you ,and also does anyone have any idea about when the full firmware will be released

sunny_deed said:
yea that was a pretty big mistake i made without looking for it, i have been told by someone that we can pull out all the require d imgs from a phone in good working condition, i asked in the hopes that someone would be generous enough to do that for me , thank you ,and also does anyone have any idea about when the full firmware will be released
Click to expand...
Click to collapse
What's wrong with the version (675) from here :-
https://www.mobileheadlines.net/download-huawei-honor-9-lite-firmware-files/

Sparkrite said:
What's wrong with the version (675) from here :-
https://www.mobileheadlines.net/download-huawei-honor-9-lite-firmware-files/
Click to expand...
Click to collapse
there is no Fullota version in there

sunny_deed said:
there is no Fullota version in there
Click to expand...
Click to collapse
Go:
https://forum.xda-developers.com/9-lite/development/stock-rom-indian-firmware-c675-t3813875

sunny_deed said:
there is no Fullota version in there
Click to expand...
Click to collapse
My bad, I was only trying to help.............
Anyway you have it now (post above) thanks to @BS4388 and @VigneshS007 .

Nokia 8 TA-1004 Stuck on EDL mode

Hi all, this happened because I tried to downgrade my phone's firmware from Pie (2019-05 security patch) to 8.1.1 using the zip file in this thread. I did it once with stock recovery, unlocked the bootloader successfully and installed TWRP 3.2.3-1-NB1, then updated via OTA to Pie.
Then I tried to downgrade again using TWRP and after the reboot the phone was stuck on 9008 mode.
I'm trying to reflash it using OST 6.0.4 but it just says "Please connect your phone"
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
So the big question is. How do I revive my phone? Thanks in advance for any replies.

Angcrad said:
Hi all, this happened because I tried to downgrade my phone's firmware from Pie (2019-05 security patch) to 8.1.1 using the zip file in this thread. I did it once with stock recovery, unlocked the bootloader successfully and installed TWRP 3.2.3-1-NB1, then updated via OTA to Pie.
Then I tried to downgrade again using TWRP and after the reboot the phone was stuck on 9008 mode.
I'm trying to reflash it using OST 6.0.4 but it just says "Please connect your phone"
So the big question is. How do I revive my phone? Thanks in advance for any replies.
Click to expand...
Click to collapse
Remove OST LA and install NOST,start the program, and when the phone turned off press and hold volume down button and turn on phone while pressing volume down,it goes to download mode,than select firmware and select method of flashing called Emergency mode and Factory reset and try to flash.It need few minutes for flashing.

Allek84 said:
Remove OST LA and install NOST,start the program, and when the phone turned off press and hold volume down button and turn on phone while pressing volume down,it goes to download mode,than select firmware and select method of flashing called Emergency mode and Factory reset and try to flash.It need few minutes for flashing.
Click to expand...
Click to collapse
Thanks for the info. How do I turn the phone off? I know it is in a powered state because Windows sees it as QDLoader 9008, but the screen is dark, the backlight is off and when I try to charge it, it seems dead.

Angcrad said:
Thanks for the info. How do I turn the phone off? I know it is in a powered state because Windows sees it as QDLoader 9008, but the screen is dark, the backlight is off and when I try to charge it, it seems dead.
Click to expand...
Click to collapse
Try to press and hold all tree buttons for 3/4 minutes .
Sent from my TA-1012 using Tapatalk

Allek84 said:
Try to press and hold all tree buttons for 3/4 minutes .
Sent from my TA-1012 using Tapatalk
Click to expand...
Click to collapse
Tried holding down the 3 buttons for 5 minutes, phone is still powered ond (even though screen shows nothing) I know it is still drawing a current because it gets warm if I keep it in its box.
Will try with NOST later. Thank you

Nokia 8 stuck 9008 edl
Angcrad said:
Hi all, this happened because I tried to downgrade my phone's firmware from Pie (2019-05 security patch) to 8.1.1 using the zip file in this thread. I did it once with stock recovery, unlocked the bootloader successfully and installed TWRP 3.2.3-1-NB1, then updated via OTA to Pie.
Then I tried to downgrade again using TWRP and after the reboot the phone was stuck on 9008 mode.
I'm trying to reflash it using OST 6.0.4 but it just says "Please connect your phone"
So the big question is. How do I revive my phone? Thanks in advance for any replies.
Click to expand...
Click to collapse
Install firmware usnig QFile tool
Search google Nokia 8 firmware
Open firmwarex

Angcrad said:
Hi all, this happened because I tried to downgrade my phone's firmware from Pie (2019-05 security patch) to 8.1.1 using the zip file in this thread. I did it once with stock recovery, unlocked the bootloader successfully and installed TWRP 3.2.3-1-NB1, then updated via OTA to Pie.
Then I tried to downgrade again using TWRP and after the reboot the phone was stuck on 9008 mode.
I'm trying to reflash it using OST 6.0.4 but it just says "Please connect your phone"
So the big question is. How do I revive my phone? Thanks in advance for any replies.
Click to expand...
Click to collapse
Yo tengo la solucion,

Critical bootloader
Hi guys, I'am in same boat as Angcrad. I tried the NOST but when I flash it says that "Your phone is protected to flash unprotected software. Is your bootloader unlocked to critical?" What does this mean?

Angcrad said:
Tried holding down the 3 buttons for 5 minutes, phone is still powered ond (even though screen shows nothing) I know it is still drawing a current because it gets warm if I keep it in its box.
Will try with NOST later. Thank you
Click to expand...
Click to collapse
@Angcrad
Hey man, have you had any luck with your Nokia 8?
I'm having the same problem with a 1 year dead Nokia 8 :'(

holding down the 3 buttons and plug your usb
Problem Solved
Nokia 8 -Ta 1004