Hello guys, after 3 years with my device the power button died on me, so I ordered this replacement on Amazon, and replaced it myself, I had changed the screen and battery before also, with no problems so far.
So, I open the phone, and it had 3 stripped screws:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I used a 1 mm drill do remove them, and apparently (visually) I didn't do any damage to the device.
I had to add the battery, the camera glass and another part to the replacement, I don't know what it does:
It's not connected by wire, just by "pressure".
Ok, I turn on the phone, on wifi, and everything works great(Signal had full bars). So I closed it without the missing screws.
When I went out to dinner, by 4G had full bars, no X, but not working. I tested with an app, and it showed the signal was ok.
I did an Network Reset, and it didn't help at all.
Now most of the time I have ZERO signal, or 4G with an X, sometimes HSPA works perfectly, sometimes with an X, today I had 4G working for 30 minutes, with 5mb down and 0.25mb up, but right now Zero signal again, and I was in São Paulo and Rio, so big cities with total 4G and 3G coverage.
I didn't have time to do a full wipe because of the holidays, but I don't think it's software related, but I will.
I don't know where the antenna is, or if I could have damaged it, but it makes no sense for me to have full bars and data one minute, and none on the other.
I will open it up again, and also do a full wipe, but I'm curious if someone here have some insight about this problem.
Nexus 6 7.1.1 N6F27I (August 5,2017)
Magisk v14.0
Again, it was working on 4G with 50mb speeds (Max in Brazil for me) moments before my repair.
Thank you very much!
That would be 1 of the 2 speakers that is circled in red. I have torn mine apart atleast 25 times over the years and no signal issues but I did try and find the antenna contacts awhile back and from what I could gather, didn't spend alot of time looking, but they make contact around near the top corners, either one or both I cannot remember, you can see the small square gold contacts in the picture, then from the contacts into the actual midframe itself, hence why there are the 8 "joints" around it, 2 on each corner, I believe those are the antenna lines as it would have been easier for them to just make the midframe a solid piece over multiple parts. I have bent one of my corners to where I can move one of the corners a pretty good amount almost pulling it apart when it's just the midframe by itself so I don't think it's damaged Soo easily, rather try cleaning all of the gold contacts around the midframe, also look very very close at the "pins"(?) That the contacts line up with on the Mobo, they are tiny as hell and can be bent easy, if one is then that could explain it, isopropyl alcohol 89% or higher will clean any surface and is safe, 99% if ur pharmacy carries it lol. Before all that try the baseband cache eraser in the radio thread and flash it in TWRP, maybe flash the newest radio before you resort to opening her up again. Good luck!
LaGgY_42o said:
Good luck!
Click to expand...
Click to collapse
Thank you, I didn't open it again because of the holidays, and I will make a full reflash tomorrow.
Using the drill made a bit of iron powder, it might be it somewhere on a connection, I have the isopropyl alcohol at home, I will try it too.
Thank you for the answer!
Febag92 said:
Thank you, I didn't open it again because of the holidays, and I will make a full reflash tomorrow.
Using the drill made a bit of iron powder, it might be it somewhere on a connection, I have the isopropyl alcohol at home, I will try it too.
Thank you for the answer!
Click to expand...
Click to collapse
Not a problem. Far as the metal shavings goes I'd personally take a very close look over everything, softest bristle toothbrush you can find normally works well for cleaning without damaging anything, I've also found one of my girls smaller/thinner makeup brushes worked wonders for not only the inside but insanely well on the front speaker grills lol. Also as I'm sure you know speakers having magnets inside them it would be a good place for metal shavings to build up. Also if you are having any issues with the speakers or feel they are low they are like $5 or less on Amazon.
Don't worry about a screw or 2 missing lol, think mines missing 2 itself also the middle red circled screw you highlighted, the one above the bottom most highlighted screw, along with, (I believe it to be the one to the right of the camera housing, be careful with them as if they are tightened down past a point they beging putting pressure on the screen bowing it out. Try to go little by little and feel the screen as you tighten to assure it's still flat.
LaGgY_42o said:
Also as I'm sure you know speakers having magnets inside them it would be a good place for metal shavings to build up.
Click to expand...
Click to collapse
I felt really naive when you said it was the speaker, it was so obvious, it was a magnet! Thank you again, I will take a better look inside! :fingers-crossed:
Related
I Got a white housing off ebay for my girlfriend 32A.
Here's the issue. I can't put the screws back on the new case, the threaded sleeves are not present and I doesn't look like I can remove them from the old housing.
Anyone else had this issue, any solutions, other then hot glue haha ?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
You can take them out, but it's unbeleivably difficult. I would just buy from this site: http://cnn.cn/shop/tmobile-white-housing-p-6164.html
Although it's more expensive, it'll save you the hassle. There are also housings which have those golden rings there but your screws won't fit it lol. i've gone through this haha
How can you remove them ? Pull out ? or you have to break the plastic around it and then it won't fit in the holes ?
same problem here took apart my mytouch. and now stuck. I am going to melt the old housing and attempt to pop the screwholes (gold threads) out of the older housing. and pop them in. if not i guess gorilla glue -_-
well ive heard some ppl lighting the end of something like I dunno, a nail and somehow pull it out. (I dont know at all to be honest) I've tried, and it sticks RIDICULOUSLY HARD. From my experience, I would suggest you not bother with it and get a refund or something, or complain and say it doesnt have enough w/e for u to put it on
lol solder the housing together?
Sent from my T-Mobile myTouch 3G using the XDA mobile application powered by Tapatalk
spammer said:
Anyone who has the same problem, can try to buy the tool like the attached picture. The tool is called soldering iron for your solution partner.
Hope that it will help.
thanks
Click to expand...
Click to collapse
Can you tell me what I should do with that ?
CasseTrop said:
Can you tell me what I should do with that ?
Click to expand...
Click to collapse
you do know if your faceplate locks in to the middle portion, you can just leave it like that. unfortunately My Mytouch (32b) does not have any screws on it. doesnt affect functionality. fortunately the faceplate (32b) fits the stock middle portion. its tight, but locks in accurately with out having to use screws. also the adhesive left behind by the stock faceplate was strong enough to glue in the new faceplate. I got lucky. I tried prying off the new faceplate after installation (in an attempt to fix my previously damaged vibration motor and the LED) it wouldnt budge so I left it alone. your best bet is to use adhesive (glue) and make sure it does not dry, or drip into any circuits or the screen itself. dont use glue if the faceplate snugs in tight, just put a plastic shield/case over it so even if you accidentally drop it, the faceplate wont come off. good luck.
Thanks for the advice but I want it OEM style (with screws) or it will just stay black original housing.
Not having the screws makes the phone look a bit loose and bleh. Also, if they dont include the gold rings or w/e on your faceplate, they probaly didn't include anything else which would mean your LED won't show in the front and the speakerhole /earpiece or w/e its caled i forget! Will look weird. I suggest you try the one I showed you or like you said, stick with the original housing. That's probably the best!
maybe you bought a 32b housing personally mines fine, and i fixed my led lol. forgot to put the clear plastic. anyway my phone is ok w out screws. just have to be careful not to drop it on a hard surface.
Sent from my T-Mobile myTouch 3G using the XDA mobile application powered by Tapatalk
KAwAtA said:
Not having the screws makes the phone look a bit loose and bleh. Also, if they dont include the gold rings or w/e on your faceplate, they probaly didn't include anything else which would mean your LED won't show in the front and the speakerhole /earpiece or w/e its caled i forget! Will look weird. I suggest you try the one I showed you or like you said, stick with the original housing. That's probably the best!
Click to expand...
Click to collapse
The led stuff and speaker hole thing it's all good, you can easily remove it from the original housing, i'm waiting on the seller to see what he has to say. I guess i'll just take my money back and leave as it is.
_ice_ said:
maybe you bought a 32b housing personally mines fine, and i fixed my led lol. forgot to put the clear plastic. anyway my phone is ok w out screws. just have to be careful not to drop it on a hard surface.
Click to expand...
Click to collapse
That's not an option for me, I just wish I could see your face when you'll drop the phone and the parts will be all over the place haha.
CasseTrop said:
The led stuff and speaker hole thing it's all good, you can easily remove it from the original housing, i'm waiting on the seller to see what he has to say. I guess i'll just take my money back and leave as it is.
That's not an option for me, I just wish I could see your face when you'll drop the phone and the parts will be all over the place haha.
Click to expand...
Click to collapse
Damn dont jinx it , nope thats why I am about to go buy a clear plastic shell for it lol. I am a motorcycle rider so portable device drops are common for me.
I got my HTC 2150mAH battery today from VZW. It's HUGE, but I've been thinking about how to make it more streamlined since I heard about it. Enter my dremel work.
Dremel out the rear of the VZW snap case to match the bulge on the new battery door. Sand it down smooth, and here you have it. It's pretty nice feeling, and it doesn't bulge out too much. It's still bulkier than before, however if you had a protective case already it isn't much of a difference.
Now, my phone looks good and holds a charge longer.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
NOTE:
Decided to meet some of the demand and offer my modding to you guys.
I will do this on a per request basis for $45 including the case, and $25 if you mail me the case yourself. This includes shipping the case to you (you pay for shipping to me). If I grab the case myself, I simply run to the VZW store and pick on up, and this saves you on shipping to me.
PM me if you want me to do this. Just give me about 5 days or so turnaround time, as I have full time obligations elsewhere.
where did you order this battery? i want one?
Best looking one I've seen yet. You should buy a bunch of those cases and modify them for sale.
At $20-$30 per case, plus the time to modify them it wouldn't be worth it to both buyer and myself. If anyone wants, send me the money and I can do it on a need basis, but I'm not going to stock these.
nice work man!
I did something very similar with mine!!!! I just cut the back out of the black silicone case so the battery sticks through the back...it looks 10x better now and I will be keeping my 2150 because of it. If people want pics of this let me know.
abe01 said:
I did something very similar with mine!!!! I just cut the back out of the black silicone case so the battery sticks through the back...it looks 10x better now and I will be keeping my 2150 because of it. If people want pics of this let me know.
Click to expand...
Click to collapse
Could you post up some pictures? The red case looks good but I'm wondering if the black case looks even better since the the phone is already black and it might blend in better.
Could you post pics I have the same case, but I'm iffy about getting the battery.
What happens to the antenna in the modified case?
I was told after checking the original back casing that the antenna is part of the backing. Now that the case has been altered did anyone think to look where the antenna is laying now. You have to look very close at the inside of the back of the case to see that the antenna was embedded and camouflaged. How is the reception?
I noticed that there are cheap Dremels on sale online. Is it ok to use a crappy cordless one for this task, since there really isn't much material to remove?
I don't have my other camera at work so I had to use the camera on the phone using a mirror. I'll try to remember to take a better pictures or pictures sometime. It looks nice though, it doesn't look silly anymore.
abe01 said:
I don't have my other camera at work so I had to use the camera on the phone using a mirror. I'll try to remember to take a better pictures or pictures sometime. It looks nice though, it doesn't look silly anymore.
Click to expand...
Click to collapse
I agree, that looks sweet. That's it i am going to break down buy a rotary tool today
I just used scissors.
looks good .. quick question how is your power button.. I had to shave mines down a bit cause it was getting stuck ..
IncredibleDoes said:
where did you order this battery? i want one?
Click to expand...
Click to collapse
Verizon is accepting phone orders of the battery. I recieved mine yesterday it feels great not having to run to a charge 49% battery ( 6:57am last charge to now 11:13pm )
that's 16 hours of moderate use and still no urgency to plug it in lmao
No takers on the Antenna question.
Got the new battery and case backing yesterday. Sure enough the antenna is mounted covertly in the center of the back of the case on the inside as is the standard one. So if the stylish have decided to cut away this area what trick was employed to replace the Antenna? How is the reception? Also, the idea of shaving down the power button is neat. Does it have a height limitation? It should have been done in the original design since it can be bumped when inside of a case which will keep initiating the screen power. Battery drain!!!!
that looks badass!!!!
Jexy said:
I was told after checking the original back casing that the antenna is part of the backing. Now that the case has been altered did anyone think to look where the antenna is laying now. You have to look very close at the inside of the back of the case to see that the antenna was embedded and camouflaged. How is the reception?
Click to expand...
Click to collapse
He didn't alter the back of the phone....he altered the snap on case...
abe01 said:
I just used scissors.
Click to expand...
Click to collapse
Duh--it didn't even occur to me to just buy a soft case. While it's always fun to play with power tools, this will be easier on the wallet. Can anyone recommend a cheap source to buy a soft/easily altered case?
Yes, click on the el cheapo case in my signature.
-------------------------------------
Sent via the XDA Tapatalk App
Hi Folks,
may I introduce you poor man's desk stand:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This construction is open source. Feel free to use and improve it as you like The only constriction is, you have to post it (photos) on this thread, if you rebuild and improve my poor man's desk stand.
yet another nice idea
DN41
I love these I always make one when someone suggests one, I've got like six littering my desk
Push this thread
haha sound tha like mate just wantz painting or graffn up
that's awesome... no charging thoug... but still... at that price...
try this....
PS: Its not me in the video !!
Cool idea I think a lot of people became poor cause of the expensiveness of the HD2
GoGo Stand
Saw this thread and just had to tell you about my friend's site that addresses this very thing. His nick is Envador, and he's become very well known for his computer case mods. Aside from that, he came up with an idea for a phone/stand and he calls it the GoGoStand. you can check them out at
http://www.gogostand.com/
They fit in your wallet and are literally the size of a credit card.
I have 4 of them.
Lord60 said:
Saw this thread and just had to tell you about my friend's site that addresses this very thing. His nick is Envador, and he's become very well known for his computer case mods. Aside from that, he came up with an idea for a phone/stand and he calls it the GoGoStand. you can check them out at
http://www.gogostand.com/
They fit in your wallet and are literally the size of a credit card.
I have 4 of them.
Click to expand...
Click to collapse
Awesome for just $5
Great job dude,
I have in my mind something like this, could you please post the measssurements of the base of your coarton dock?
I'm looking for an angled micro usb data cable so I can attach it to the dock and charge it at the same time, also I think I can get it covered with FIBERGLASS and then paintwith some glossy black spry paint..
That's what I have in mind, just need to start with the meassurements.
Thanks for all!
Lord60 said:
Saw this thread and just had to tell you about my friend's site that addresses this very thing. His nick is Envador, and he's become very well known for his computer case mods. Aside from that, he came up with an idea for a phone/stand and he calls it the GoGoStand. you can check them out at
http://www.gogostand.com/
They fit in your wallet and are literally the size of a credit card.
I have 4 of them.
Click to expand...
Click to collapse
i saw this on this on the interweb around last summer. it was not this nice, the guy had posted how to make this yourself with a template. i made one from the side of a milk jug. it worked ok. i since bought the EB with kickstand so i tossed it. i dont always use the EB so i placed an order for these things. thanks for throwing this thing out for us.
Wire stand variation allowing charging & headphones
Hi all. I decided to make a version of the paperclip desk stand that would allow me to keep the charger plugged in and listen to headphones. You will need:
- 1 plastic coated wire clothes hanger OR ~ 60 cm of coated wire - not too heavy gauge or it will be hard to bend.
- Pliers
- Cloth to grip wire with to avoid damage from pliers
- Paper to put template on
- A ruler and pen
Method: Rule a 29cm line on the paper. Starting at the left hand end, mark the following positions on the line - 6.5cm, 11.5cm, 14.5cm, 19.5cm and 28.5cm. Hold the left hand end of the wire up against the line and transfer the marks to the wire, including the 29cm end which is halfway. Turn the wire, keeping the 29cm mark in line with the end of the ruled line and transfer the marks from right back to left on the remaining ~30cm of wire. Use the pliers to trim the excess wire off the end of the wire. Now, starting in the middle of the wire, bend the wire ~75-90 degrees at the 28.5cm marks - there should be about a cm of wire between the bends. Next, bend the wire into a hairpin bend at the 19.5cm marks. Then bend the wire ~85-90 degrees at the 14.5cm marks. This makes two 5cm "legs" at the back of the stand. Bend the wire ~85-90 degrees back down at the 11.5cm marks. Then make hairpin bends at the 6.5cm marks. Using the cloth and pliers, grip the 4 "hairpins" and squeeze the wires as close together as you can get them. Last, grip the short front ends of the wire and bend them outwards to avoid scratching the phone. Voila - a stand that can hold your HD2 while it's charging (pretend my old iPaq in the pic is the HD2 I used to take the photos )
Note: it isn't super stable, but it isn't intended to be.
Note 2: the other stand is "one I prepared earlier" from an over-the-door hanger. More stable, but doesn't have room for the charging cable.
My new hobby - creative accessories for the HD2
Anybody have an invisible shield installed on their Droid 3? I just got mine in the mail today and i tried putting it on but the corners on the back keep popping up...I really dont want to pull it up and try to reinstall because I already ran out of the solution they gave me and had to use some leftover from my Touch Pro2's install kit. Any advice is helpful Thanks
Yes I had the same problem. I think I fixed it by starting at one corner of the phone, holding it down for a few seconds and slowly moving all over the outer edge. There are a few spots that curl up but it looks good.
It sucks, I think it took me an hour to get it how I felt comfortable it would not peel off.
Just keep working at it. It feels like they rushed production and it does not fit the phone the correct way.
Sent from my DROID3
yeah for all my other phones the corners were cut so the side flap folded down and the top flap had an extra edge so u could fold it up and wrap the extra peice around the corner. it looks like this one the corners are just rounded...i tried the 'palming' method and it's working but still peels up after a while. I'm trying to be patient but it's still rather annoying.
If you ran out of the solution you can just fill it up with water, the manual says up to 3 times or so. Its just soap and water.
Sent from my DROID3 using XDA App
rda990 said:
If you ran out of the solution you can just fill it up with water, the manual says up to 3 times or so. Its just soap and water.
Sent from my DROID3 using XDA App
Click to expand...
Click to collapse
Wow, that's crazy haha. I guess I should practice reading the manuals more, after doing it so many times I just take out the plastic and start going to work. This was the first time i got a refillable bottle though, maybe it's something new they do?
On another note...
As an update, i ended up taking it to a zagg kiosk at the mall and i must say, I wish i had done that to begin with. I really didn't see how their installation could be so amazing but it was FLAWLESS...I kind of wish I had stayed and watched her do it instead of walking around the mall. Maybe I could have learned her secrets so I could make it look that good myself next time around haha.
These pics were taken within 5 minutes of leaving the mall. No bubbles at all, and all corners stayed down.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
It cost $10 for the install but i think it was worth it. If it ever peels i can go get it replaced for free.
I was thinking about getting one of the invisible shields, but they seemed a bit expensive, and with a $10 applying fee (I doubt I'll be able to get it on) that's a lot for a protective film. Just wondering if other people think they're worth the price.
I think it's definitely worth the price IF you use your phone like me. I refuse to put it in a hard case and always keep in in my pocket, so it basically eliminates scratches and prevents drops because it adds a better grip/feel to the phone. Especially when taking it out of my pocket there's a chance of it slipping out of my fingers so the full body works for me. Even if you do use a case, though, the screen protector is probably a good idea. It's the best one but since it's thicker some people don't like it. I got used to it on my Touch Pro and since then i've never noticed it being hard to slide my finger on the screen. It's all up to preference basically, but there's a reason why you get multiple protectors with the cheaper versions vs. 1 with invisible shield. It just works.
Also search online for online coupons, i used Zagg20 to get a 20% discount, so all together with the install it was a little over $30. Either way you get a lifetime warranty, but if you don't get it installed by them you have to remove, ship, and reinstall the new invisible shield yourself (they reimburse for shipping) and I didn't want to struggle with the back again.
I pressed the stylus and it didn't click. I pressed it harder and it sunk into the device...
Any ideas what might have happens or how I get it back out?
When I get home, I'll try and post a picture.
I had the same issue about 3 weeks ago. I tried several ways to attempt to pry it out but was afraid of damaging the phone. I took it to the local Sprint store and they swapped me out for a new device. They did not even attempt to repair it but went right to the back and pulled a new one out of the box.
How about this - put a drop of super glue on the end of a strong string. Touch the end of the string to the end of the pen. When it's dry - pull!??
Mines imported to the UK, so unlikely to get it swapped
Yeah, I'm wondering about something sticky to pull it out.
Is it easy to get a replacement from eBay? I've also thought about just sticking a pin in it and trying to pull. Maybe drilling a small hole in the stylus to hook something in and pull. Then just replace the stylus.
Mine is stuck because I work outside and it got dust in it so the spring will not work. The only way for me to get it out is to bang it and drop it on the corner of the phone on the carpet a couple times. (obviously with a case) Have you tried this?
If it helps, this is what it looks like -
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
SpencerA99 said:
Mine is stuck because I work outside and it got dust in it so the spring will not work. The only way for me to get it out is to bang it and drop it on the corner of the phone on the carpet a couple times. (obviously with a case) Have you tried this?
Click to expand...
Click to collapse
So drop it onto the corner the stylus is in? I'll put a case on in a moment and try, thanks.
**EDIT** That worked! Thanks. Likewise, it seems the spring isn't working for some reason. I might try some lubricant, otherwise I'll order a replacement.
AndyCr15 said:
So drop it onto the corner the stylus is in? I'll put a case on in a moment and try, thanks.
Click to expand...
Click to collapse
The bottom left corner is what I used. This could work for you if it is a spring problem in the spen but if it is actually stuck in the phone then I doubt that it would work
Sorry, I edited in while you replied. Thanks, it worked!
AndyCr15 said:
Sorry, I edited in while you replied. Thanks, it worked!
Click to expand...
Click to collapse
If you get the spring to work tell me what you did so I can try. Im gettiing tired of dropping my phone to get the s pen out
Yeah, I don't fancy it myself either. I've sprayed some WD40 on it, but it doesn't seem to have helped. Looking to get the eBay seller to cover the cost of a new one, otherwise I'll just order a replacement. Looks like about $36 to ship to the UK. (About £25 for me)
UPDATE: I sprayed the end of the stylus with WD40, but not much seemed to change. I've been using a different phone for a day, come back to the Note 5 and the WD40 must have soaked in or something as it's almost as good as new.
I've done the same again, sprayed it and left it overnight and you wouldn't know there had been an issue now.
AndyCr15 said:
UPDATE: I sprayed the end of the stylus with WD40, but not much seemed to change. I've been using a different phone for a day, come back to the Note 5 and the WD40 must have soaked in or something as it's almost as good as new.
I've done the same again, sprayed it and left it overnight and you wouldn't know there had been an issue now.
Click to expand...
Click to collapse
I know this device doesn't really have much metal in it, but please be careful of using wd40. It actually causes metals to rust once it's done doing its job. It's best to use brake cleaner or silicone lubricant.
Sent from my SM-N920T using Tapatalk
Hi, thanks for the tip. I've only sprayed it on the stylus, but I guess it could corrode the spring inside?
Anyway, it's working for now at least!
Hopefully nothing else goes wrong with it. Cheers.
Well, it's been stolen now anyway! New one on the way...
How'd you lose it?
Sorry to hear that man.
Flat was burgled. Security has been stepped up and the new one arrives tomorrow!
Anyone out there find threads on this issue, or know a better solution?
This is my same issue.
Spring does not eject stylus, have to bang phone downwards.