{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I am sharing my kernel/boot.img which is build from latest source. You must have an unlocked bootloader to flash my kernel. The kernel/boot.img can be flash with fastboot or via TWRP. Before that..You should know that..
Code:
###Disclaimer###
I am not responsible if your device will be damaged, broken, boot looping. YOU are choosing to make these modification
Please read the instructions and notes before flashing anything.Please respect and try to help each other. You may face sometimes that I cannot answer your questions/or answer your questions a bit later.
I am busy with my work and don't have enough time to read and answer all your questions at the same time.
DONATE ME HERE------------------------------------------------------------
HOW TO FLASH KERNEL/BOOT IMAGES
- Flash the .zip in twrp
OR
- Extract the .zip and move the boot.img to your fastboot/adb folder
- Flash boot.img in fastboot.
Code:
- adb devices
- adb reboot bootloader
- fastboot flash boot boot.img
- Let the device boot completely
------------------------------------------------------------
27/8/2018 [Only for Android Wear 2.0]
Kernel features
- Based on latest kernel source 3.18.24.Released (VERSION = 3,PATCHLEVEL = 18,SUBLEVEL = 24)
- Compiled with 4.9.3-Optimized compiler
- dm-verity removed
- Selinux permissive default
- Scheduler optimize/support for heterogenous multi-core
- Scheduler support for heterogenous multi-processor systems
- Enables the core control
- Enable hotplug
- Set power efficient workqueue by default
- Enable 1.26GHz freq step (533Mhz, 800Mhz, 1094Mhz and 1267Mhz)
- Add Darkness CPU governors (Improve stability and keep the CPU away from max and unless it is absolutely needed)
- Multi-Cluster Power Management support
- Optimized the energy consumption for advanced multi-core SoCs including big.LITTLE.
- Multi-core scheduler enable/optimized
- Add and update Qualcomm PM driver/APM driver updated reduce battery usage during sleeping
- A lot subsystems converted to use power efficient workqueues
- Several other patches to reduce battery usage during idle state
- Tweaked/optimized the scheduler to balance the load across all CPUs without any regards to the power costs
- Tweaked the scheduler to reduce/save power by scaling down the frequency of the CPUs or idling them,
- Tweaked to predict the best time to save power on the CPU without affecting performance
- And many more can't remember
NOTE:- IMPORTANT/ HOW TO BOOST BATTERY USAGE
- USE Kernel Auditor Wear (Kernel Audiutor.. a kernel control app with many useful functions)
Kernel-Auditor-Wear
- Turn off Smart Replay and OK Google detection if you don't use it. It will reduce your battery usage.
- Set CPU GOVERNOR TO Darkness
- Turn off the ADB debugging
- Turn off Window animation scale to speed up your watch
- Turn off Always-on Screen to reduce further battery usage
- Turn off Wi-Fi if you don't use it.
Download-Link-
KERNEL/BOOT IMAGE-27-AUGUST
------------------------------------------------------------
6/8/2017 [Only for Android Wear 1.5]
- Based on available source, up to date
- Add some*I/O Scheduler, Noop, FIOPS, SIO and ZEN
- SELinux permissive
- dm-verity disabled
- Init.d script supported
- adb is enabled by default
- Simple, stable
- Tweaked to boost the performance and slightly increase battery life.
- Tweaked to launch app faster and improve the overall UI experience.
Download-Link
Kernel/6/8/2017
MD5:a8361495e177859647c66c46d49fa2f3
------------------------------------------------------------
------------------------------------------------------------
Kernel Source
https://github.com/toffyjan/Asus-zenwatch-3-kernel
----------------------
IF YOU LIKE MY WORK AND WANT ME TO CONTINUE, THEN BUY ME A SHOT OF WHISKY
---------------------------------------------------------------------------------
DONATE ME HERE
---------------------------------------------------------------------------------
Special thanks to:
@Chainfire for great work in android
@Maxr1998 thanks for script and twrp recovery
@superR for the kitchen
@Captain_Throwback
Please always support devs and others (soon).
27/8/2018 [Only for Android Wear 2.0]
Kernel features
- Based on latest kernel source 3.18.24.Released (VERSION = 3,PATCHLEVEL = 18,SUBLEVEL = 24)
- Compiled with 4.9.3-Optimized compiler
- dm-verity removed
- Selinux permissive default
- Scheduler optimize/support for heterogenous multi-core
- Scheduler support for heterogenous multi-processor systems
- Enables the core control
- Enable hotplug
- Set power efficient workqueue by default
- Enable 1.26GHz freq step (533Mhz, 800Mhz, 1094Mhz and 1267Mhz)
- Add Darkness CPU governors (Improve stability and keep the CPU away from max and unless it is absolutely needed)
- Multi-Cluster Power Management support
- Optimized the energy consumption for advanced multi-core SoCs including big.LITTLE.
- Multi-core scheduler enable/optimized
- Add and update Qualcomm PM driver/APM driver updated reduce battery usage during sleeping
- A lot subsystems converted to use power efficient workqueues
- Several other patches to reduce battery usage during idle state
- Tweaked/optimized the scheduler to balance the load across all CPUs without any regards to the power costs
- Tweaked the scheduler to reduce/save power by scaling down the frequency of the CPUs or idling them,
- Tweaked to predict the best time to save power on the CPU without affecting performance
Hi tested for some days good performance and battery is so difficult make miracles with this device but everything work fine, thanks
Installed kernel on stock rom on january 31st, running fine, no problems, battery life seems better
Thanks for this, I really like it with the swift rom on the watch. Is there any way to install a boot screen (like the android wear)?
29/5/2018 [Only for Android Wear 2.0]
Kernel features
- Based on latest kernel source 3.18.24.Released (VERSION = 3,PATCHLEVEL = 18,SUBLEVEL = 24)
- Compiled with LINARO GCC: 5.2-Optimized
- dm-verity removed
- Selinux permissive default
- Scheduler optimize/support for heterogenous multi-core
- Scheduler support for heterogenous multi-processor systems
- Enables the core control
- Added fsync on/off support
- Enable hotplug
- Set power efficient workqueue by default
- Enable 1.26GHz freq step
- Multi-Cluster Power Management support
- Optimized the energy consumption for advanced multi-core SoCs including big.LITTLE.
- Multi-core scheduler enable/optimized
- Add Qualcomm PM driver/APM driver updated reduce battery usage during sleeping
- A lot subsystems converted to use power efficient workqueues
- Serveral other patces to reduce battery usage
- Tweaked/optimized the scheduler to balance the load across all CPUs without any regards to the power costs
- Tweaked the scheduler to reduce/save power by scaling down the frequency of the CPUs or idling them,
- Tweaked to predict the best time to save power on the CPU without affecting performance
- And many more can't remember
NOTE:- IMPORTANT
- USE Kernel Auditor Wear (Kernel Audiutor.. a kernel control app with many useful functions)
Kernel-Auditor-Wear
- Set CPU maximum frequency to 1267 MHz
- Set CPU minimum frequency to 533MHz
- Set CPU Governor to POWER SAVE. IT WILL KEEP THE LOWEST FREQUENCY AS MUCH AS POSSIBLE.
Never used this but happen to stumble upon it, so tried installing the May version. Running latest Swift ROM from this forum. Installed this kernel image and when I rebooted I had no bluetooth and couldn't turn it on. Flashed back the boot image from Swift and my bluetooth is back. Not sure why this didn't work.
elkay said:
Never used this but happen to stumble upon it, so tried installing the May version. Running latest Swift ROM from this forum. Installed this kernel image and when I rebooted I had no bluetooth and couldn't turn it on. Flashed back the boot image from Swift and my bluetooth is back. Not sure why this didn't work.
Click to expand...
Click to collapse
I will take a look. Thanks for the feedback.
Hi and many thanks again @janjan !
Installed your kernel and same bluetooth problem : disabled and can't be enabled.
Fwiw, this is usually a sign that the wifi (or other) kernel module is out of sync with the rest of the kernel. Probably a simple fix for him to make.
BOOT_IMAGE_23_MAY download link not working today...
re: May 23rd kernel
Nascar Dog said:
BOOT_IMAGE_23_MAY download link not working today...
Click to expand...
Click to collapse
@Nascar Dog
You are lucky, you have not yet installed it. LOL
The kernel is not useable, it messes up the
watch making it not useable.
Good luck,
Have a great day!
I was able to simply revert to my previous kernel and reapply the root zip to get back up and running. Didn't need to reset anything. That's a temp solution until the bluetooth/wifi issue is fixed.
Nascar Dog said:
BOOT_IMAGE_23_MAY download link not working today...
Click to expand...
Click to collapse
Use the old one until I fix the BT issue.
Misterjunky said:
@Nascar Dog
You are lucky, you have not yet installed it. LOL
The kernel is not useable, it messes up the
watch making it not useable.
Good luck,
Have a great day!
Click to expand...
Click to collapse
Umm I will say BT is broken. Not like useable ..maybe if u don't know how to use kernel Audiutor app.
elkay said:
I was able to simply revert to my previous kernel and reapply the root zip to get back up and running. Didn't need to reset anything. That's a temp solution until the bluetooth/wifi issue is fixed.
Click to expand...
Click to collapse
Yes. Don't need to reset anything. Just flash the old kernel.
re: Kernel - Bluetooth
janjan said:
Use the old one until I fix the BT issue.
Umm I will say BT is broken. Not like useable ..maybe if u don't know how to use kernel Audiutor app.
Yes. Don't need to reset anything. Just flash the old kernel.
Click to expand...
Click to collapse
@janjan
The Zenwatch 3 is a Bluetooth Tethering device so it's pretty
much unusable and useless if the bluetooth is not working.
Good luck,
Have a great day!
elkay said:
Never used this but happen to stumble upon it, so tried installing the May version. Running latest Swift ROM from this forum. Installed this kernel image and when I rebooted I had no bluetooth and couldn't turn it on. Flashed back the boot image from Swift and my bluetooth is back. Not sure why this didn't work.
Click to expand...
Click to collapse
Zebnastien said:
Hi and many thanks again @janjan !
Installed your kernel and same bluetooth problem : disabled and can't be enabled.
Click to expand...
Click to collapse
elkay said:
Fwiw, this is usually a sign that the wifi (or other) kernel module is out of sync with the rest of the kernel. Probably a simple fix for him to make.
Click to expand...
Click to collapse
Nascar Dog said:
BOOT_IMAGE_23_MAY download link not working today...
Click to expand...
Click to collapse
Misterjunky said:
@janjan
The Zenwatch 3 is a Bluetooth Tethering device so it's pretty
much unusable and useless if the bluetooth is not working.
Good luck,
Have a great day!
Click to expand...
Click to collapse
New kernel is available for download. BT and wifi are fixed. Enjoy (29/5/2018)
https://www.androidfilehost.com/?fid=746163614322267786
MD5: 87adedd2b4e8227c8d4a8506087c2074
Yeah ! Testing right know...
- Bluetooth is working fine. Don't know about wi-fi.
- Smoothness seems to be greatly improved.
- Can't install my apps from my phone in playstore (unable to install : Bluetooth connexion required). I don't know if it is caused by busybox (never installed before). I will investigate...
Great job @janjan ! Many thanks for keeping our watches up !!
i am stuck at twrp, cannot into os , any idea?
kennyloy said:
i am stuck at twrp, cannot into os , any idea?
Click to expand...
Click to collapse
Flash stock recovery
I can't select 1267 MHz as max frequency, only 1094MHz.
Related
LuPuS Kernel Stock
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hi I have kernels for the PLAY and one for the PRO, ARC/S users where pm'img me to make my one for the PRO compatible
with the ARC/S. Unfortunately they never got back to me about testing, But no worries as besttt said he would test
for me and thanks to his extensive testing it was able to boot and apparently is super smooth well i'll release so you can all test
it out for your selves :good:
Disclaimer
Code:
[COLOR="DarkOrchid"]#include[/COLOR] [COLOR="Magenta"]std.h[/COLOR]
[COLOR="Blue"]/*
* Your warranty is now void.. LOL I guess you knew it already.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, you getting dumped or you getting fired because your phone*
* bootloops and alarm does not go off. Please do some research if you have any *
* concerns about features included in my kernel before using it! YOU and only*
* YOU are choosing to make these modifications.
*/
[COLOR="Magenta"]#ifdef[/COLOR]
You have a [COLOR="DarkGreen"]question[/COLOR] post it in the [COLOR="DarkRed"]thread[/COLOR],
Instead of [COLOR="DarkGreen"]Pm'ing me[/COLOR], as other users may
experience your [COLOR="DarkRed"]problems[/COLOR]
[COLOR="Magenta"]#endif[/COLOR][/COLOR]
Included in kernel
[/LIST]
Added Io-schedulers --
- Noop
- Anticipatory
- Deadline
- CFQ
- BFQ
- SIO
- ZEN
Added Governors --
- lagfree
- brazillianwax
- smoothass
- scary
- savagedzen
- smartass
- smartassv2
- smartassH3
- interactivex
- minmax
- powersave
- performance
- conservative
- ondemand
- interactive
- userspace
+
Lulzactive - Thanks to Tegrak
Based on Interactive and Smartass. When workload is greater than or equal to 60%, the governor scales up
CPU to next higher step. When workload is less than 60%, governor scales down CPU to next lower step.
When screen is off, frequency is locked to global scaling minimum frequency
Virtuous
Virtuous is a modded smartassV2 which gives even more battery time then smartassV2
Intellidemand - Thanks to faux123
This is an intelligent ondemand that enters browsing mode to limit max frequency when GPU is idling,
and (exits browsing mode) behaves like ondemand when GPU is busy; to deliver performance for gaming and such.
Intellidemand does not jump to highest frequency when screen is off.
Lazy - Thanks to Ezekeel
The Idea here is to eliminate any instabilities caused by fast frequency switching by ondemand.
Lazy governor polls more often than ondemand, but changes frequency only after completing min_time_state
on a step overriding sampling interval.
Lazy also has a screenoff_maxfreq parameter which when enabled will cause the governor to always
select the maximum frequency while the screen is off.
-Ondemandx:
Basically an ondemand with suspend/wake profiles. This governor is supposed to be a battery friendly ondemand. When screen is off, max frequency is capped at 500 mhz. Even though ondemand is the default governor in many kernel and is considered safe/stable, the support for ondemand/ondemandX depends on CPU capability to do fast frequency switching which are very low latency frequency transitions. I have read somewhere that the performance of ondemand/ondemandx were significantly varying for different i/o schedulers. This is not true for most of the other governors. I personally feel ondemand/ondemandx goes best with SIO I/O scheduler.
-Lionheart:
Is a conservative-based governor. The tunables (such as the thresholds and sampling rate) were changed so the governor behaves more like the performance one, at the cost of battery as the scaling is very aggressive.
To 'experience' Lionheart using conservative, try these tweaks:
sampling_rate:10000 or 20000 or 50000, whichever you feel is safer. (transition latency of the CPU is something below 10ms/10,000uS hence using 10,000 might not be safe).
up_threshold:60
down_threshold:30
freq_step:5
Lionheart goes well with deadline i/o scheduler. When it comes to smoothness (not considering battery drain), a tuned conservative delivers more as compared to a tuned ondemand.
BadAss Governor:
Badass removes all of this "fast peaking" to the max frequency. Badass will also take the gpu load into consideration. If the gpu is moderately busy it will bypass the above check and clock the cpu with 1024Mhz. If the gpu is crushed under load, badass will lift the restrictions to the cpu.
Superbad -
A "superbad" super smooth rendition of a highly optimized "smartass" governor!
Darkside -
A "slightly more agressive smart" optimized governor!
What else-----
-SLQB - (SLAB allocator with Queue)-(both)
This memory allocator is designed for small number of CPUs system (such as desktop or smart phone devices). This allocator is design to be simple and it is optimized for using order-0 pages as much as possible (order-0 pages are the simplest therefore quickest type of memory in a Linux system to allocate).
- Added Cleancache
- Supports ext 2,3
- Updated zRam
- Lzo compression/decompression speed has doubled on average.
- Init.d support
- Fudgeswap
- And much more
- O/C and stable upto 2ghz, although I do not recommend O/C to 2ghz for long periods of time, do so at your own risk.
Show your support for the kernel and my work by putting this in your signature, its only a quick one I done up with my limited time
Code:
http://i.imgur.com/xtWNL.png
A big thanks to -
gu5t3r
DooMLoRD
Jimbo77
xeozus
NobodyAtAll
Faux123
Erasmus
Leedroid
FXP Team
Jerpelea
[NUT]
besttt - testing
tempest918 - For the Logo
Sinkster - testing
besttt - testing
Phil3759
CTCaer
For v2 i've started from scratch from Sony's xx.587 sources, I know everything might not be added and some things may need to be fixed
so anything that needs to be fixed or you would like to be added leave a suggestion (not an order) in the thread. Everything mentioned above has been added.
Downloads in post 2
Kernel source --- -branch master
https://github.com/garwedgess/LuPuS-STOCK-ICS-Xperia2011
CWM source -- https://github.com/garwedgess/android_bootable_recovery -b lupus-cwm
Changelog
Code:
[B]Previous releases[/B]
[hide]
[U][B][COLOR="Blue"]What's been added in v3[/COLOR][/B][/U]
[LIST]
~2 Way call recording
~ Ext4 support
~ More battery friendly (so far so good)
~ Increased WiFi signal strength
~ Free’d Ram
~ GPU Overclock
~ Made kernel smoother
~ Might of left one or 2things out here
~ 0% battery patch thanks to Bazoocaze
[/LIST]
[U][B][COLOR="Blue"]What's been added in v4[/COLOR][/B][/U]
[LIST]~ Fixed not booting issue
~ Fixed GPU OC 200+ points improvement for 2D & 3D
~ Added Full Custom Voltage control
[/LIST]
[B][U][COLOR="Blue"][B][U]Whats new in v6[/U][/B][/COLOR][/U][/B]
[LIST]~ Completely fixed boot problem[COLOR="blue"][COLOR="Red"] (boot is set to 806MHz, don't complain as you will OC anyway :p)[/COLOR][/COLOR]
~ Quicker boot time
~ Fixed battery issues :fingers-crossed:
~ Added governor-- [COLOR="SeaGreen"]Intellidemand2[/COLOR]
~ Fixed GPU OC
~ Wifi Signal and lock on much quicker/better
~ Alot of clean-ups & small fixes
~ kgsl: Use highest performance level on wake-up from sleep
[/LIST]
[B][COLOR="Blue"]New in v8[/COLOR][/B]
- Added USB OTG support (see attachments in Downloads section)
- Tweaked Intellidemand2 Thanks [user=1844875]@CosmicDan[/user] - Dbus_ramping = gives project butter feel :)
- Removed CIFS & NFS to help increase battery (test)
- Disabled my disablng of sched feature
- More tweaks
- Possibly more
[B][U]v9[/U][/B]
- Improved Battery Life alot :)
- Thumbee support
- ARM7 optimizations
- Brought OC back down to 1.6 max (no need for it above 1.6 unless u want to kill your device)
[B]- Kernel sources completely reworked started from scratch o Sony xx.587 sources[/B]
- Tiny RCU
- Upddatedd patched and fixed LZO
- lowered vfs cache pressure
- Increased Wifi- Range and added support for channel 14
- 0 % Battery patch - Thanks @ Bazoocaze
- Better memory copy
- Better memory move
- LMK Optimizations (LowMemoryKiller)
- VDD support (voltage conrol)
- Linaro Optimzations
- Compaction added
- KSM
- CIFS (improved support)
- NTFS
- USB OTG
- Updated to newest SIO Io-Scheduler
- Google Snappy Compress & Decompress
- Added Vibrate To Recovery (Notification to enter CWM)
- Wifi module size drasticly reduced
[B][U]v10[/U][/B]
- Built with Linaro 4.7.3 (02-01-13)
- Reworked Ramdisk, uses new method
- Auto Root updated to SuperSU, only roots device if Superuser.apk or SuperSU.apk dont already exist
- New LuPuS menu - check in post #1 on how to use it
- Build in wifi modules ( if wifi modules don't work on first install reboot)
- Built in CIFS & USB OTG (from lupus menu)
- Built in zRam, you can also change zRam size (from LuPuS menu)
- TWRP and latest CWM Recovery {change default in LuPuS Menu)
- Supports Gb and ICS (GB has wifi broken ATM)
- Tweaks menu from LuPuS menu script
- Free'd 11mb RAM
- cgroup scheduling
- binder changes from 2.6.32.60
- binder: Fix use of uninitialized variable.
- net sched: fix some kernel memory leaks
- net/ipv4: Eliminate kstrdup memory leak
- ipv4: force_igmp_version ignored when a IGMPv3 query received
- pids: Fix a race in pid generation that causes pids to be reused immediately
- smart toggle overclock upto 2ghz
- changed RD compression to LZMA
- enable group scheduling
- removed some debugging
- cleaned up config
- USB tether
- enable ipsec tunnel support in kernel
- SQLITE3 DB vacumming
- Further compressed ramdisk
- disabled cuse, enabled md4 + nls_utf8 as modules
**Probably alot more but this is all I can remember for now**
[B]-v11[/B]
- [COLOR="Red"]Updated kernel to 2.6.32.60[/COLOR]
- CWM = volume down
- TWRP = volume up
- Complete clean up and new improved LuPuS Menu
- Free's more RAM 360mb RAM in total now
- Fixed AROMA
- Backport Binder from CAF 3.4.0
- Triple Buffer
- Frandom
- Tweaked deadline
- Tweaked SmartassV2
- New governor SmartassH3
- New IO-Scheduler ZEN
- Patch so entropy no longer depletes
- Zcache
- ARM optimizations
- Genlock backported from CAF
- Replaced old compaction with newer/better version
- Backported logger from CAF and free'd RAM from logger
- Updated improved LMK
- Removed fudgeswap
- Updated crc32 lib from 3.3 kernel
- New net scheduler Stochastic Fair Blue (SFB)
- Optimized Tiny RCU
- CFS tweaks
- Quick keyboard reset (hold HOME + POWER)
- Timed_gpio backported from CAF
- Snapdragon optiizations
- Improved boot time
- Improved wifi to load at first boot
- Removed Autoroot feature
[URL="https://github.com/garwedgess/LuPuS-STOCK-ICS-Xperia2011/commits/2.6.32.x"]** Plus more see here for all patches and credits**
Also Big thanks at gu5t3r and [NUT][/URL]
[B]v12[/B]
- Fixed HDMI
- Fixed Video playback/recording
- Reverted back to linux kernel 2.6.32.9
- Removed triple buffer (caused some lag)
- Fixed problem with root @ gu5t3r
- LuPuS Script now runs properly from Terminal Emulator @ gu5t3r
- Free RAM = 355mb and is stable
- Added fool-proof to ramdisk -- if non-supported Android version is found (not ICS or GB) Kernel will boot into CWM
[B]v13[/B]
- Fixed CPU Governor and Frequencies not sticking at boot -- thanks [user=4665716]@gu5t3r[/user]
---- Custom CWM
- Clean-up of menu
- Added own wipe options menu -- with extra options
- Aroma File Manager from CWM --- Must have aroma ([COLOR=Red]aromafm.zip) placed on root of sdcard[/COLOR])
- Multi zip installer
- Reboot options - Power off re-added under this menu
- Pointless but people keep asking me for it so re-added wipe battery stats also.
- LuPuS themed...
[B]v14[/B]
- Fixed Camera Key
- Kernel works on CM9
- Removed persistent RAM
- Remove other errors from dmesg
- Improved wifi loading
- Disabled Key Reset (can be enbled in LuPuS Menu)
---- CWM updated to 6.0.3.2
- Fixed Advanced restore
- Fixed busybox symlinks generation (aka) fixed CWM backup not working
- Fixed install from sideload being mixed up with toggle signature
- Remove confirmation from install from sideload as it can be cancelled at anytime.
---- Complete Ramdisk Clean up & Improvment
- Reworked booting
- Supports m2sd and other ap2sd scripts
- Force booting -After 2 Vibrations Hold Home for ICS
-Hold Home and press VolDown for CM9
-Hold Home and press VolUp for GB
- Fixed Reboot To Recovery (It reboots to last one used IF you don't have scripts that wipe /cache on boot)
- Reworked Kernel logs, they are located at /cache/recovery/ and /data/local/tmp/
- Improved init.d
- lupus menu clean up
- Added Vendor fix from Hallon & Anzu
- option to mount / unmount
- Backup / Restore /system/vendor
- Boot.d - If phone is taking a long time to start move suspicious init.d scripts to /system/etc/boot.d
They will be run in background and won't affect boot time.
[B]v15[/B]
- Added Ultra-KSM
- Tuned Governors
* superbad
* lionheart
* virtuous
* darkside
* conservative
* smartassH3
- Really use google snappy zRam (improves zRam)
- Fix nasty sigreturn bug
- Fix compiler warnings
- Do uninteruptible sleep
- Other various fixes
- Removed GB & CM9 support
- Other various ramdisk improvments
- Updated TWRP - Mounting Mass Storage should be fixed
- Updated LuPuS CWM to latest Official CWM changes
* Fixed advanced restore
* Removed Reboot Options
* Brough Reboot System Now back to Main Menu
* Brought Power Off back to Main Menu
* After install of zip dont return to main menu
* Minor UI changes
- Fixed Mounting Vendor (please test can be set via lupus menu)
- patch can also be forced at boot by
hold home + hold voldown = force ics + vendor patch
hold home + tap vol down = force ics
key -- Thanks [user=4665716]@gu5t3r[/user][/hide]
[B]v16[/B]
- Fix some lag in gaming
- Set default swappiness to 20
- Removed fsync
- Removed Cleancache
- Removed zCache
- Removed WasActive page flag
- Removed Zen IO-Scheduler
- Fixed issue with some devices booting into CWM
- Fixed CWM install options order
- Fixed TWRP adb and mounting USB storage
- Fixed PATH for LuPuS Menu
- Added UKSM options to LuPuS-Menu
Downloads
If you like my work please consider buying me a beer or something else
by clicking the DONATE ME button, of course it isn't needed but greatly appreciated and keeps me motivated.
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
LuPuSv16 Downloads
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
If you need root for STOCK ROM
Code:
[COLOR="Purple"]Root[/COLOR] : ( Flashable via recovery )
* SuperSU : [URL="http://download.chainfire.eu/204/SuperSU/"][COLOR="Green"][U]Download[/U][/COLOR][/URL]
* Superuser : [URL="http://androidsu.com/superuser/"][COLOR="Green"][U]Download[/U][/COLOR][/URL]
CWM = VOLUME DOWN
TWRP = VOLUME UP
LuPuS_anzu_Stock-iCsv16-full.img
md5 = a2d14f97a76afcae5de3a4654c554ca0
Wifi is build in NO NEED for WIFI MODULES.ZIP
Mirrors - and all other releases
http://www.goo.im/devs/wedgess
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
ALL PREVIOUS VERSIONS ARE HERE-------
ARC-kernel-folder
ARC-wifi-folder
Check your MD5 match the above if not re-download
LuPuS MENU
To Run LuPuS Menu use either ScriptManager get it HERE on google playstore
Or
Use Terminal Emulator get it HERE on google playstore.
Code:
su
lupus
* information is in lupus menu
1/ CIFS Menu *
Enable
Disable
2/ zRam Menu *
Enable
Disable
Set zRam size ( default is 60)
3/ Frandom Menu *
Enable
Disable
4/ USB OTG *
Enable
Disable
5/ Clean and Remove tweaks
Remove init.d's
6/ Tweak Menu
Note all tweaks are preset from here and option to set as init.d's
Clean all temp files
SQLITE optimizations
LMK Optimizations
Network optimizations
Defend against ARP spoofing
Remove android logger
SDcard speed tweak
Flag blocks as non-rotational
7/ Performance Menu
Note all options are se by user input from here and option to set as init.d's
Set CPU frequencies
Set Governor
Set IO-Scheduler
Voltage Control
VM tweaks (explained below)
VM Tweaks
dirty ratio and dirty background ratio 1 & 2
This controls how often the kernel writes data to "disk" (in our case the internal microSD system card, not the removable microSD card). When your apps write data to disk, Linux actually doesn't write the data out to the disk right away, it actually writes the stuff to system memory and the kernel handles when and how the data is actually going to be flushed to the disk. These values represent a percentage, the higher the percentage, the longer it waits to flush, the lower the percentage, the more often flushes will occur. Now remember, we are dealing with solid state storage, not the traditional disk platter and spindle. So we are actually able to delay flushes a little longer with solid state versus a traditional hard drive disk.
dirty_expire_centisecs
How old "dirty" data should be before the kernel considers it old enough to be written to disk. It is expressed in 100ths of a second.
dirty_writeback_centisecs
This is the interval of when the writeback daemons periodically wake up and write "old" data out to disk. It is expressed in 100ths of a second.
min free kbytes
This is used to force the Linux VM to keep a minimum number of kilobytes free. The VM uses this number to compute a pages_min value for each lowmem zone in the system. Each lowmem zone gets a number of reserved free pages based proportionally on its size. Default is 2048kb.
overcommit_memory
This controls overcommit of system memory, possibly allowing processes to allocate (but not use) more memory than is actually available.
0 - Heuristic overcommit handling. Obvious overcommits of address space are refused. Used for a typical system. It ensures a seriously wild allocation fails while allowing overcommit to reduce swap usage. root is allowed to allocate slighly more memory in this mode. This is the default.
1 - Always overcommit. Appropriate for some scientific applications.
2 - Don't overcommit. The total address space commit for the system is not permitted to exceed swap plus a configurable percentage (default is 50) of physical RAM. Depending on the percentage you use, in most situations this means a process will not be killed while attempting to use already-allocated memory but will receive errors on memory allocation as appropriate.
Swappiness
A property for the Linux kernel that changes the balance between swapping out runtime memory, as opposed to dropping pages from the system page cache. Swappiness can be set to values between 0 and 100 inclusive. A low value means the kernel will try to avoid swapping as much as possible where a higher value instead will make the kernel aggressively try to use swap space.
VFS Cache Pressure
File system cache (dentry/inode) is really more important than the block cache above in dirty ratio and dirty background ratio, so we really want the kernel to use up much more of the RAM for file system cache, this will increas the performance of the system without sacrificing performance at the application level. The default value is 100, as a percentage, and what you want to do is lower the value to tell the kernel to favor the file system cache and not drop them aggressively.
8/ Enable / Disable Quick Key Reset
- Reboot device quickly by Holding HOME and POWER Key (Disabled by default)
- Enable
- Disable
9/ Vendor Options
- Fix for Anzu and Hallon Vendor problem
- Mount
- Unmount
- Backup
- Restore
Compatible
Hi!
This kernel is compatible with .587 LT15i?
Sorry...xD "CM9 based"... for Play
Or what?
bukest said:
Hi!
This kernel is compatible with .587 LT15i?
Sorry...xD "CM9 based"... for Play
Or what?
Click to expand...
Click to collapse
Its for ARC and ARCS its stock based and off .4 sources untill I see if it's popular or not if it is I will update during the week to new sources
and add in Aroma file manager when you hit volume down button and CWM when you hit back button :good:
CM9/10 kernels maybe coming soon, i'll see if I can make time for it
what governors do you recommend?? and can i have swap and zram, both of them, activated at the same time??
wedgess said:
Its for ARC and ARCS its stock based and off .4 sources untill I see if it's popular or not if it is I will update during the week to new sources
and add in Aroma file manager when you hit volume down button and CWM when you hit back button :good:
CM9/10 kernels maybe coming soon, i'll see if I can make time for it
Click to expand...
Click to collapse
Hm... Flashed this without any problem and any FC on .587 a few minutes ago.
It's so fast. ))
Now, try the wiFi and Zram enabler.
WiFi's fine. Noticable difference immediately, I'll leave it overnight and see what happens...
(ignore the sig, I'm running Miui v4 atm)
sinkster said:
WiFi's fine. Noticable difference immediately, I'll leave it overnight and see what happens...
Click to expand...
Click to collapse
Same here, but WiFi has something wrong. It's turn on, but didn't connect to my router with WPA2 security.
"Connecting..."
'Authentication..."
"Connecting..."
'Authentication..."
...
did you have arc or arc s?
---------- Post added at 02:05 AM ---------- Previous post was at 02:04 AM ----------
bukest said:
Same here, but WiFi has something wrong. It's turn on, but didn't connect to my router with WPA2 security.
"Connecting..."
'Authentication..."
"Connecting..."
'Authentication..."
...
Click to expand...
Click to collapse
wait for a fix we just want more users to report:good:
---------- Post added at 02:06 AM ---------- Previous post was at 02:05 AM ----------
sinkster said:
WiFi's fine. Noticable difference immediately, I'll leave it overnight and see what happens...
(ignore the sig, I'm running Miui v4 atm)
Click to expand...
Click to collapse
arc or arc s user?
besttt said:
did you have arc or arc s?
Click to expand...
Click to collapse
Arc(LT15i) with stock 4.1.b.0.587
bukest said:
Arc(LT15i) with stock 4.1.b.0.587
Click to expand...
Click to collapse
iam thinking that only arc have wifi working arc s failed for the moment lets wait and other reports
can anyone tell me wath governors are the best for this kernel??
jarein95 said:
what governors do you recommend?? and can i have swap and zram, both of them, activated at the same time??
Click to expand...
Click to collapse
Ye zram may cause lag it doesn't for me on the PLAY but you can always disable it, probably intellidemand, superbad, ondemandx, darkside and for battery virtuous=1/3rd better then stock
sinkster said:
WiFi's fine. Noticable difference immediately, I'll leave it overnight and see what happens...
(ignore the sig, I'm running Miui v4 atm)
Click to expand...
Click to collapse
What you using ARC or ARC S???
Click to expand...
Click to collapse
And please hit thanks in the OP, I don't have this phone and didn't need to spend time making this,
but thought
I'd help the community, All it is is clicking a button :good:
No wifi in my arc S!!
Sent from my LT18i using xda app-developers app
Ok looks like for now wifi only works on the ARC ill get it working on the ARC S asap probably tomorrow or when i get time
Sent from my GT-I9300
its amazing kernel sooooooooooooooooooooooooooooooo smoooooooooooooooooooooth
but unfortunately wifi not working
request please
1) can u add the new source
2) can u increase the wifi signal when u fix it for arc s users
3) can u add more ram
best wishes and gooooooood luck to u
-----------------------------------
sent from LT8i ARC S
unlocked bootloader
Sorry man, this kernel is based on .587 source?
Charging
Charging from USB isn't work for me.
dr said:
its amazing kernel sooooooooooooooooooooooooooooooo smoooooooooooooooooooooth
but unfortunately wifi not working
request please
1) can u add the new source
2) can u increase the wifi signal when u fix it for arc s users
3) can u add more ram
best wishes and gooooooood luck to u
-----------------------------------
sent from LT8i ARC S
unlocked bootloader
Click to expand...
Click to collapse
Yes depending on how it does ill build from newest source. And more ram so u want me to break 720p recording??
HorvathTheWizard said:
Sorry man, this kernel is based on .587 source?
Click to expand...
Click to collapse
No for now it .4 sources will update tho maybe today, depending
bukest said:
Charging from USB isn't work for me.
Click to expand...
Click to collapse
Ohhhh ok will have to fix that later when im home looks like ill just have to build from newest sources
Sent from my GT-I9300
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hello!
I want to introduce my first custom kernel for the ZTE Axon 7. This is based of several sources, I cherry-picked commits to make improvements to the stock LOS kernel. I'm not a developer, but i really like to port stuff over .
We'll have one single kernel for both LOS and STOCK based off LOS sources and I will try to have updated with each and every commit that is submitted and the other one will be Stock ZTE sources based. If you want to request for specific features, let me know and i'll do my best to bring them over.
Special Features:
BLX (Battery Longevity eXtender) added, check Post#2 for instructions.
Updated to lastest LOS Stock Kernel
Added a few governors like: lionfish / despair / darkness / blu_active / wheatley / ironactive and bioshock
added a few IO Schedulers: Tripndroid / Zen / SioPlus / VR
Kcal Color Control driver
USB Fast Charge
SafetyNet Patch (Bypass bootloader unlocked check)
Dynamic Fsync control
a little Overclock
Motorola Quickwake
Extended battery charge time from 30s to 100s
and manny other small fixes (you can check the commits in the sources)
Download
Disclaimer: I am not responsible if you use this and brick your device or if your device blows up, implodes, flames start shooting from it or it kills your neighbor's dog. Flash at your own risk. I am not responsible.... It was the other guy... I swear....
Latest LOS Release: AX7-Hybrid-R21 for STOCK and R22 for LOS[/URL
Known issues:
02.13.2017 - CPU Freq don't always stick, known issue caused by other drivers. Phone will eventually set your frequencies, dont' panic.
Special Thanks to:
jcadduono
franciscofranco
bedalus
lord_boeffla
flar2
sultanxda
...and many others from whom i cherry pick commits... Sorry if I forgot to mention anyone!
XDA:DevDB Information
AX7Kernel, Kernel for the ZTE Axon 7
Contributors
jimbo77
Source Code: https://github.com/Jimbo77
Kernel Special Features:
Version Information
Status: Stable
Current Stable Version: R22
Stable Release Date: 2017-06-02
Created 2017-02-14
Last Updated 2017-06-02
Reserved
Wifi Fix if not available with AX7-Hybrid in LOS based ROMS
The problem is that for some reason the ROM does not load the wlan.ko module at boot, so if you run into a "no wifi" situation with a LOS Based ROM all you have to do is navigate to the sbin folder and run the shell script named insmod.sh with your favorite ROOT Explorer APP. Right after you execute the file Wifi will be available. I'm looking into a permanent solution for this, stay tuned.
How to Bypass SafetyNet bootloader and/or root checks
* If comming from a clean flash of ROM or GAPS only do the following:
Magisk Approach
Flash the UnSu file from HERE
Flash my latest Kernel
Flash the latest Magisk from this thread:
Donwload Magisk Manager from the Playstore
Enable Magisk Hide in Magisk Manager
Profit, SafetyNet Checks will pass, all green!
SuperSU Approach
Flash the UnSu file from HERE
Flash my latest Kernel
Flash the latest SuperSU from this thread:
Donwload RootSwitch APP from HERE
Unpack the zip and install the apk inside it
Open Root Switch and disable root
Profit! SafetyNet checks will all be green!
Battery Life Extender (BLX) feature
In order to configure the cap you'll have to navigate to:
Code:
/sys/class/misc/batterylifeextender/charging_cap_level
edit the file and put the cap you want the battery to charge to, i won't recommend setting a cap lower than 90% cause then the phone could abruptely stop a fast charging cycle and damage your battery. If you want to have your phone charging to 100% just put 100 in the file and close it. No need to reboot, just plug and unplug your charger.
On a side note, this value will be set at 97% after every boot. So you'll need to manually change it back to 100.
AX7Kernel Changelogs:
AX7-Hybrid R22- 06/02/2017
Removed the WiFi module and instead it is now compiled within the Kernel to fix the problem with the Hotspot
AX7-Hybrid R21- 05/23/2017
Split both kernels, now there is a STOCK and LOS version again due to the camera incompatibility between Stock B25 and LOS.
Updated Camera driver from B25 2017U. Do not attempt to use on any other variant because it will break your camera. You've been warned!
Adreno Idler added
Updated LOS Kernel Sources
AX7-Hybrid R20- 05/02/2017
Temp camera fix for B25 2017U users. Do not attempt to use on any other variant because it will break your camera. You've been warned!
Added other options that i can't remember now (You can check my github ). I will release a new update once B25 source is released and from there update the changelog properly.
AX7-Hybrid R14 - 04/17/2017
Fix issues with Big Cluster, it was not being properly handled. Keep an eye on Core_CTL it might affect the way the big.LITLE arch works.
Updated F2FS to latest 3.18.y branch from HERE
Updated F2FS encrypt system to a per File encrypt system
Updated the way the scripts determine user setup to properly patch for Wifi Fix on AOSP based ROMS.
Added the option to patch the fstab.qcom file with F2FS support on System partition, Data and Cache was already there. THIS IS ONLY FOR LOS based ROMS, i didn't add the patch for fstab.qcom for STOCK. I'll look into this within this week.
Enabled NTFS FS
Updated Wifi Driver
AX7-Hybrid R13 - 04/09/2017
Fix Core_CTL. It was not working properly in R12
AX7-Hybrid R12 - 04/09/2017
Fixed WiFi for AOSP ROMS. It will execute a script based on the setup of the user. Depending on Stock or AOSP
Enabled Core_CTL Helpers and hotplug wrappers.
AX7-Hybrid R11 - 04/09/2017
Fixed several Memory Leak sources
Increased screen off sampling for Interactive Governor, should fix some Bluetooth hiccups when playing music either locally or streamed.
UPSTREAM ANDROID - SDCARDFS
Added more wake-locks to be disabled and make the disable process more strict, it's user responsibility any issues due to disabled wake-locks.
Read through the commits in github
AX7-Hybrid Basic R1 - 03/25/2017
AX7-Hybrid Basic is up... Only added Kcal, SafetyNet Patch, Quickwake, CPU and GPU OC
AX7-Hybrid R10 - 03/24/2017
AX7-Hybrid R10 is up... AKA the one Kernel to rule them all!. Please Red Post 2 with info regarding Wifi on LOS based ROMS...
AX7Kernel R7 - 03/16/2017
For both STOCK and LOS Based versions. Upstream Linux Kernel to 3.18.45 thanks to jcadduono patches.
AX7Kernel R6 - 03/03/2017
Cap for battery charging set back to 100% by deffault. BLX Settings, you want to change them, refer to this POST and to this POST. If you want to extend your battery's life think about adding the cap to a 95 or 97%
Fixed the issue where the phone won't go into deep sleep at all.
WQ_POWER_EFFICIENT MODE is enabled by default now.
AX7Kernel R5 - 03/01/2017
Cap for battery charging set to 97% by deffault. BLX Settings, you want to change them, refer to this POST and to this POST. Your battery won't charge beyond 97%.
Added options to manipulate thermal settings, now you can choose when the phone will throtle the CPU or when to start shutting down cores to prevent damage. My recommendation don't push it too high or your phone might get damaged due to the high temps. It's not set to 60 Celcius so i recommend lowering that to avoid damage.
Added WQ_POWER_EFFICIENT MODE ( you'll need EX Kernel manager to get this, it's paid app but it's totally worth it guys)
Enabled the option to 'disable' some wakelocks. Disable them on your own risk. Wakelocks that can be disabled are: Bluedroid, wlan_rx, wlan_ctrl, wlan, IPA_WS, wlan_extscan_wl_ws, qcom_rx_wakelock_ws - You'll also need EX Kernel manager to get this options.
AX7Kernel R4 - 02/24/2017
Renamed both the Folder and Kernel zip file to appoint to the version. Now we'll have 2 versions, LOS and Stock AX7Kernel, make sure to check the zip name correctly to avoid issues when cross flashing kernels. All LOS/RR/AOKP and other LOS Based kernels will have the word LOS in it.
Fixed BLX feature. It should now properly stop the charging process when the battery has reached the cap_level set by users. Charge will resume once the charge drops from the cap assigned.
AX7Kernel R3 - 02/21/2017
Added one more step of OC (pushed just a little bit further)
Added my own and really simple implementation of BLX (battery life extender) based on the work made by bedalus for the OP3 and OP3T
AX7Kernel R2.3 - 02/17/2017
Updated to latest LOS Stock Kernel
Disabled some debugging
fixes to ZEN ioScheduler - highly recommended now.
Disabled color inversion in Kcal - can't be used anyways.
Fixed USB Fast Charge - Should worl properly now.
GPU OverClock - 684MHZ max frequency now.
Adreno Boost added and enabled (should boost GPU a bit)
Updates to interactive governor (should work better when operation are in the background and screen is off - music streaming is an example.
Changes to the Sync
Changes to Random function for IO ops.
Updates to Zram.
AX7Kernel R1 - 02/13/2017:
Updated to latest LOS Stock Kernel
Added a few governors like: lionfish / despair / darkness / blu_active / wheatley / ironactive and bioshock
added a few IO Schedulers: Tripndroid / Zen / SioPlus / VR
Kcal Color Control driver
USB Fast Charge
SafetyNet Patch (Bypass bootloader unlocked check)
Dynamic Fsync control
a little Overclock
Motorola Quickwake
Extended battery charge time from 30s to 100s
Nice! Flashing now and testing and will report back.
Edit : Trying to flash the kernel on the latest 14.1 Official nightly, but I get an error 1 in TWRP. Any suggestions? Thank you.
jimbo77 said:
... {snip} ......my first custom kernel for the ZTE Axon 7 ......{snip} .... [/QUOTE]
Really great to see further & ongoing development fot this great hardware. Your wide range of options leads inevitably to the question: Based upon your testing and build, what selection have you found the best for SOT & performance? (knowing ones's mileage will always vary based upon specific, etc)
Thanks!
Click to expand...
Click to collapse
TheLastSidekick said:
Nice! Flashing now and testing and will report back.
Edit : Trying to flash the kernel on the latest 14.1 Official nightly, but I get an error 1 in TWRP. Any suggestions? Thank you.
Click to expand...
Click to collapse
Don't know what the issue is. Are you running the latest TWRP?
I justo downloaded the file and it flashed well into my device
kcal, more governors and overclock?
kickass
amphi66 said:
Really great to see further & ongoing development fot this great hardware. Your wide range of options leads inevitably to the question: Based upon your testing and build, what selection have you found the best for SOT & performance? (knowing ones's mileage will always vary based upon specific, etc)
Thanks!
Click to expand...
Click to collapse
As you said it will depend on each user and the usage of the phone. I personally use ironactive / tripndroid / overclock / cpu touch boost / enabled dynamic file sync.
Test it and let me know
jimbo77 said:
Don't know what the issue is. Are you running the latest TWRP?
I justo downloaded the file and it flashed well into my device
Click to expand...
Click to collapse
Thanks, sorry. Not sure either. Flashed latest by jdac 3.0.3.4 I believe?? Now it says N after you said that I checked recovery once more. Reporting back soon.
jimbo77 said:
As you said it will depend on each user and the usage of the phone. I personally use ironactive / tripndroid / overclock / cpu touch boost / enabled dynamic file sync.
Test it and let me know
Click to expand...
Click to collapse
Just adjusted color a bit and oc'ed. So far it's pretty sweet. Going to try out your settings right now.
---------- Post added at 11:30 PM ---------- Previous post was at 11:21 PM ----------
Got everything but touch boost... Is that input boost? If so what freq did you use.
Is the video recording bug gone with this kernel? Would love to try but need video recording for work.
EasyTiger6x13 said:
Is the video recording bug gone with this kernel? Would love to try but need video recording for work.
Click to expand...
Click to collapse
I've been able to record a couple of videos and have no issues at all
What tuning app are you using? Kernel aduitor?
RUNNERX said:
What tuning app are you using? Kernel aduitor?
Click to expand...
Click to collapse
Yes.
Side note, my recovery problem was fixed. Make sure you're all on the latest recovery, mine got replaced somehow.
Anyone got any tips or settings for screen calibration they care to share?
Do I need to have root to install?
SafetyNet Patch isn't working for me on A2017g LOS 14.1 official. CTS Profile Match : false
jimbo77 said:
Don't know what the issue is. Are you running the latest TWRP?
I justo downloaded the file and it flashed well into my device
Click to expand...
Click to collapse
Same problem here error1.
Is this compatible with A2017G?
Running the 3.0.n1-1 Twrp.
Official LOS 14.1 13/2 nightly.
zguy30 said:
Do I need to have root to install?
Click to expand...
Click to collapse
No you don't need to have root.
tron1 said:
SafetyNet Patch isn't working for me on A2017g LOS 14.1 official. CTS Profile Match : false
Click to expand...
Click to collapse
This is an issue with a su add on found in those roms. Flash this file:
https://drive.google.com/file/d/0BzZ9GYzoA6tMd1NVTXROSGZ3RTg/view?usp=drivesdk
Then flash the kernel again. Then SafetyNet will pass, if you want to have root then flash supersu 2.79 and use root switch to disable root whenever you need to use anything that checks SafetyNet.
This are my results with above steps...
machetie said:
Same problem here error1.
Is this compatible with A2017G?
Running the 3.0.n1-1 Twrp.
Official LOS 14.1 13/2 nightly.
Click to expand...
Click to collapse
Make sure you have the latest recovery
FENIX
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Disclaimer:
use this kernel at your own risk. Flashing it may brick your device. I'm not responsible for any software/hardware and any kind of damages/losses.
I make this kernel for my own, and decided to share with community.
The goal of this kernel is to maintain stability over performance, and extend for what possible the battery backup. Enjoy.
What's in it:
Code:
-Gpu Underclock to 160mhz
-Gpu uv -50mv
-Lastest Caf Tag
-Lastest wlan drivers
-Kcal, display color full control
-Sound Control
-PowerEfficientWq
-F2fs
-Vibration Control
-Compiler Optimizations
-Battery Tweaks
-EAS
-Performance tweaks
-Refer to changelog or to git to all the tons of features
-Some other patches, check github
Flash in Twrp
Changelog-HMP-:
Code:
12/09/2019--LoveEdition--
- Android 10 ready
- Drg: Overclocked big cores too, like sdm660: 2.2ghz
- rebased again to new cleaned sources with latest nikki merges
- upstreamed to 4.4.191 + LA-UM-0074 wlan drivers, built inline
- Sultan's Ion, Iommu, ashman drivers, for improved performances
- Goodboi governor: an impulsed tweaked by me for battery
- kgsl: dispatch commands by using a master ktrhead: to reduce jitter by alot
- pl2: set gpu idle timeout to 64ms (like b2n\drg)
- ddrbus: changed governor to avoid 100% freq stuck
- allowed deeper idle cores\cluster
- source cleaned, keeped only the useful commits
- and alot, alot more. Check git.
13-07-2019-1644:
- rebased all to drg lastest sources to avoid any kind of source corruption
- camera drivers fully reverted to stock source to avoid any kind of problems (i will not touch nothing there in future)
- builded with gcc9 with alot of fixes
- upstreamed to 4.4.185 + LA.UM-0072 wlan drivers, builded inside the kernel
- we are module free
- sdm636 have now only little cpu freqs like sdm660: we cant afford 2.2ghz on 3000mah battery
- sdm630 fully supported
- nokia b2n fixed rotation bug
- cpu input boost
- disabled debugfs, tracing, loggings, debugs, i mean, not all of them but TONS OF THEM
- deleted most of unused drivers, like dvd players, cassette drivers (wtf nikki)
- disabled nikki usless drivers
- alot of workloads on power efficient workqueques
- vibration control (maybe not in b2n)
- sound control , with no metallic sound
- 160mhz initial gpu freq to save power + -50v undervolt for better power consumption
- sdFat driver, lastest version
- KCAL fixed, updated and optimized for sdm660 family processors
- zram lz4 compression for better perf
- disabled crc check
- blocked ipa and other wakeloks (but no boeffla wkl blocker for now)
- gpu will wake up only if there is a ioctl rather then a touch input, to save power
- reduced the max voltage allowed for the panel
- lowered cpu\gpu thermals to avoid device damage
- new fenix banner for recovery
- console framebuffer optimizations for 70% better perf
- 3 x faster integer than stock
- interactive optimizations
- idle lite changes
- don't need to flash magisk after flash
- and other tons of optimizations, but carefully cherry picked from the best devs around here
-refer to build date as build number
Changelog-EAS-:
Code:
-basically, all the feats of Fenix HMP
-EAS energy model by @nysadev (fantastic)
-some governors, blu_schedtuil, schedutil,
-dont let gcam and settings waste power on background
-removed some other logspams\debugs
-cpuidle lpm prediction tuning, for better idle battery saving
-removed dsboost\dynamicstune boost, to save power
-builded with Ofast
-alot of tasks uses interrutible w8s , for better idle
-100hz otpimizations
-backported PELT from 4.14 , for better power consumption/performance
-alot of sched patches
-alot of gpu performance improvements
-enabled ram ECC for faster reboots (this is awesome)
-aligned strcmp to 64kb cache line
-alot of cache optimizations by Sultan
- rewrited iommu/Ashman from sultan
- optimized for armv8
- increased kgsl priority: more smoothness
-boot speed optimizations
-cpu idle further optimizations
-PELT optimizations
- Foxed snapdragon 630 EAS bootloop
- updated my energy model for 630 by porting nysadev capacity based one for sdm660: this will give more battery and smoothness
- suppress debug verbose and disabled exp rcu like in sdm660
- removed the usless tz_log, that was spamming and yelling in the background (tx to bielfiboi to discover this)
- builded with gcc 9.1 -ofast
- very good battery backup, performance
DOWNLOAD-HMP-
DOWNLOAD-EAS-
ALWAYS wipe dalvik cache after flashing the kernel, or you will encounter bugs.
Enjoy,
feedback is appreciated.
Thanks to:
@madpausa, without him I would never have approached a linux distro
@hmd
@xda
and all the other authors of the hundreds of commits in github !
XDA: DevDB Information
Fenix kernel for NokiaDRG\B2N\PL2
Compiler: GCC-9.1
Branch: Android 9.0
Kernel Version: 4.4
defconfig: nokia_defconfig
Source Code:
FENIX
Thanks for your work but the links are all wrong...the place where the vbmeta files should be linked links to the kernel and the place where the kernel should be linked is broken.
Now my phone is in a bootloop and I dont have the vbmeta files.
the download link at the bottom, its not working
hazam1992 said:
Thanks for your work but the links are all wrong...the place where the vbmeta files should be linked links to the kernel and the place where the kernel should be linked is broken.
Now my phone is in a bootloop and I dont have the vbmeta files.
Click to expand...
Click to collapse
https://drive.google.com/file/d/1ifnXCIdkqKnk_a1HII9RqQd5CVFWz1xR/view
link fixed
Always look what you flashing, besides i ve inverted the links.
Flash this, you will recovery your phone.
prajwal05 said:
the download link at the bottom, its not working
Click to expand...
Click to collapse
i had to rebase all my work, use this:
https://mega.nz/#!kx8wGCDD!hC-l2OxIJpKEwWrOivr6TTnPpA607HQ3gm0QqH_TxPk
It's in test stage, keep this in mind. The disclaimer in the first post is still valid.
Alpha-2:
Link
-Zen i\o
-Boeffla Wakelock Blocker with specific device wkl
-Sound Control
-Kcal display control
-Fast Charge
-Toggle Input boost
-disabled gentle fair sleepers
-Performance\battery optimizations
-many more, check git
On my Nokia 7 Plus TA-1046 with Pie (march patch) the flashing of alpha 2 kernel went well and wifi works
death_jax said:
On my Nokia 7 Plus TA-1046 with Pie (march patch) the flashing of alpha 2 kernel went well and wifi works
Click to expand...
Click to collapse
Glad to hear that, we had problems with wifi. Report to me about battery\performance if you can.
Beta 1:
-250hz
-Alucard, Darkness, Darknessv5, Nightmare governors
-Disabled crc checks
-Power_Efficient_Wq
-Gpu optimizations
-Simple_gpu driver for battery\performance
-Crypto optimizations
-Cpu target optimizations flags
-Ext4 Optimizations
-selinux tuning
- -80mv Gpu Uv
-many more, check github
paul89rulez said:
Glad to hear that, we had problems with wifi. Report to me about battery\performance if you can.
Click to expand...
Click to collapse
Battery and performance seems good, like stock kernel.
The only bug that I noticed (in your and DarkOne kernel) is that the voice of someone answering a call is a bit metallic
death_jax said:
Battery and performance seems good, like stock kernel.
The only bug that I noticed (in your and DarkOne kernel) is that the voice of someone answering a call is a bit metallic
Click to expand...
Click to collapse
can you give me logs after a call? you can take it with matlog from playstore.
I n my nokia x6 all seems ok. It's a strange bug, but i will try to investigate. Thanks for the report.
A question: bluethoot it's working good for you?
Can I use this kernel with Magic?
paul89rulez said:
can you give me logs after a call? you can take it with matlog from playstore.
I n my nokia x6 all seems ok. It's a strange bug, but i will try to investigate. Thanks for the report.
A question: bluethoot it's working good for you?
Click to expand...
Click to collapse
Yes, the Bluetooth works good...
PS: if it could be useful (as you asked in the Nokia Mobile channel on Telegram to another user), I've TWRP flashed permanently (without touching vbmeta partition), Magisk with both no encryption and dm-verity
However, I can send you log, but how can I find call section?
---------- Post added at 03:41 PM ---------- Previous post was at 03:40 PM ----------
gpablo1 said:
Can I use this kernel with Magic?
Click to expand...
Click to collapse
Yes, of course.
First flash kernel and then, without rebooting, flash Magisk
After extensive testing with good testahbois (@Gravemind2015 @themetester):
DFkReborn v1.0
-removed cpu_inputboost
-msm_performance re-enabled
-Wifi\Network speed tweaks
-ExtFat support
-LA.UM-067
-Cpu\DDR boost tweaks
-Gpu Tweaks
-GraviboiFlavours
-GiorgiboiFixes
-many, many more on git.
Enjoy, and stay boi
Confirmed working like a beast on TA-1045 appreciate your efforts :highfive:
Could anybody tell me how to configure it with EX Kernel Manager?
saiz0313 said:
Could anybody tell me how to configure it with EX Kernel Manager?
Click to expand...
Click to collapse
stock settings are enough
excellent work
Sometimes I cannot use Google Camera. restore to stock kernel fixed
lllluzhnan said:
Sometimes I cannot use Google Camera. restore to stock kernel fixed
Click to expand...
Click to collapse
Same issue here. Green photos and then total crash.
No issues with stock kernel.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Designed to give better battery life without compromising performance or features
Features:
- Latest kernel tags
- Built with proton clang 11
- Built with O3 optimizations
- Use arm64 optimized functions
- Improved schedutil governor
- Use Power-efficient workqueue
- Use 300hz config
- USB fast charging
- GPU boost
- improved charging stability and speed
- use Maple IO scheduler by default
- use BBR TCP Congestion by default
- Dynamic stune boost v3
- Upstreamed and optimize CPU boost
- Disable readahead by default (improves power consumption and performance)
- CRC check toggle (disabled by default)
- Boeffla wakelock blocker
- Thermal profile control
- Kcal control
- Disable gentle fair sleepers
- Use LZ4 compression for zram by default
- Various memory, IO, and power optimizations
Installation:
- Reboot to recovery
- Backup your current kernel(boot.img)
- Go to install
- Flash kernel zip
- (reflashing magisk is not necessary)
- Reboot
- Enjoy!!
Downloads:
- Github Releases
- Builds Channel(bi-weekly builds)
Credit:
- all the people I cherry-picked from
- xda and google for having best tutorials/guides for everything
XDA:DevDB Information
Dark Ages, Kernel for the Xiaomi Poco X2
Contributors
blacksuan19
Source Code: https://github.com/Blacksuan19/kernel_dark_ages_phoenix
Kernel Special Features:
Version Information
Status: Testing
Current Stable Version: Segundo
Stable Release Date: 2020-06-27
Created 2020-05-21
Last Updated 2020-10-02
Changelog:
Tercero 03/10
• Rebase to new sm6150-dev base
• Bring on features from old Segundo release
• Boots on Android 11
• Upstream to the latest Linux stable
• Upstream wireguard to latest version
• Fixed boot issues on other roms with new trees
• Fixed always on display (roms need to enable this to work)
• Fixed slow charging while using phone
• Improved charging stability
• Improved fingerprint stability
• Improved idle drain (almost 0% now overnight)
• Disable a bunch of useless logging configs
• Various power management enhancements
• Many more improvements and performance enhancements
Segundo 27/06
- Upstream to latest 4.14.186
- Built with O3 optimizations
- Update touchscreen driver
- Fix random bootloop issue
- Fix white screen issue
- Fix Fluctuation in power
- Fix Unbalanced power supply
- Various fixes and enhancements to thermal driver
- Enable kernel ultra low power mode
- Allow GPU to go to sleep
- Improve Walt scheduler
- Block more annoying wakelocks
- Optimize memcpy and memmove
- Use arm64 optimized memcmp
- Use high priority workqueue for kgsl and devfreq
- Disable unused temperature sensors
- Remove Dynamic Fsync
- Other fixes and performance improvements
Primero 22/05
- Fix high idle battery drain
- Fix device not going into deepsleep
Primero 20/05
• Initial release
Reserved
good to see much more development here.... i really cant wait to get my device, tha pandemic is affecting tha shipping and there is delay.
Use this kernel for Havoc OS. The rom will become much better. And why aren't there any recent changelogs for the ROM?
Works with Both MIUI 12 and custom Roms ? Please reply
ft.varun said:
Use this kernel for Havoc OS. The rom will become much better. And why aren't there any recent changelogs for the ROM?
Click to expand...
Click to collapse
its already the default havoc kernel
sibikallikkat said:
Works with Both MIUI 12 and custom Roms ? Please reply
Click to expand...
Click to collapse
someone confirmed it working on MIUI, I haven't tested personally
Nice to see one more Kernel. I did test this https://github.com/Blacksuan19/kern...o-hot-fix/Dark-Ages-Primero-22052020-0313.zip
Here are my observations:
Pros:
1. Very smooth and fast (read more in cons), keeps the phone really cool
2. Good to see you have retained 300 Mhz minimum and I observed cores go to 300 Mhz very fast after tasks are done and stay there when idle
3. When the phone is idle CPU is at 300 Mhz also have seen current drain/draw is < 100 ma for 30% of times (and 40-50% of times its below 150 ma and some spikes around 200 ma - 250 ma at times) which is amazing, am sure we should get very good battery life with this.
Cons:
1. I saw few stutters at times, like freezes. I had to lock the phone n unlock it to release from those freezes (these are not due to any apps etc, faced on with this Kernel and when I went back to Optimus 10.5 (like 10.5 because it supports 300 Mhz min and not 10.6 ) I stopped seeing them, never saw any such things on optimus.
2. Even though cores go to 300 Mhz and stay there when idle, when phone is locked and nothing running in background, I saw 0% deep sleep, same settings/environment optimus sleeps like a baby
Please fix these two and this kernel is golden
coolcorner said:
Nice to see one more Kernel. I did test this https://github.com/Blacksuan19/kern...o-hot-fix/Dark-Ages-Primero-22052020-0313.zip
Here are my observations:
Pros:
1. Very smooth and fast (read more in cons), keeps the phone really cool
2. Good to see you have retained 300 Mhz minimum and I observed cores go to 300 Mhz very fast after tasks are done and stay there when idle
3. When the phone is idle CPU is at 300 Mhz also have seen current drain/draw is < 100 ma for 30% of times (and 40-50% of times its below 150 ma and some spikes around 200 ma - 250 ma at times) which is amazing, am sure we should get very good battery life with this.
Cons:
1. I saw few stutters at times, like freezes. I had to lock the phone n unlock it to release from those freezes (these are not due to any apps etc, faced on with this Kernel and when I went back to Optimus 10.5 (like 10.5 because it supports 300 Mhz min and not 10.6 ) I stopped seeing them, never saw any such things on optimus.
2. Even though cores go to 300 Mhz and stay there when idle, when phone is locked and nothing running in background, I saw 0% deep sleep, same settings/environment optimus sleeps like a baby
Please fix these two and this kernel is golden
Click to expand...
Click to collapse
Logs would be a lot more helpful for both of us
blacksuan19 said:
Logs would be a lot more helpful for both of us
Click to expand...
Click to collapse
Sorry have been busy.
Am new to this kernel things etc, if there are any links on how to get logs (or you could let me know here), would re-flash your kernel when am back and share the logs with you.
coolcorner said:
Sorry have been busy.
Am new to this kernel things etc, if there are any links on how to get logs (or you could let me know here), would re-flash your kernel when am back and share the logs with you.
Click to expand...
Click to collapse
Yhu can try catlog app... It should work!!!
@blacksuan19 do yhu mind updating tha kernel... Thanks!!!
kernel is updated almost weekly, CI builds are on the telegram channel
blacksuan19 said:
kernel is updated almost weekly, CI builds are on the telegram channel
Click to expand...
Click to collapse
What does CI means?
Thanks... Just downloaded and flashed tha latest update!
whalesplaho said:
What does CI means?
Thanks... Just downloaded and flashed tha latest update!
Click to expand...
Click to collapse
continuous-integration, meaning it will build automatically whenever there are changes to the GitHub repo
Thanks dev
I was very upset with the battery backup. But ever since I used this kernel, I am getting a very good battery backup. Please do not stop developing this kernel.
jeetu93 said:
Thanks dev
I was very upset with the battery backup. But ever since I used this kernel, I am getting a very good battery backup. Please do not stop developing this kernel.
Click to expand...
Click to collapse
Are you using it on miui or custom kernel?
fahmiroslee said:
Are you using it on miui or custom kernel?
Click to expand...
Click to collapse
Custome ROM
Does this kernel support miui? I tried flashing it on miui but my screen isn't responding to my touch.
after a long wait
tercero is finally out!
check the second post for full changelog and new features.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Code:
[COLOR="blue"]You are not allowed to take, modify, use, upload ANY file or the whole ROM without my permissions.[/COLOR]
Your warranty (is expired? if not PM me how you managed to keep it otherwise) is now void.
I am not responsible for bricked devices, dead SD cards, thermonuclear war,
or [COLOR="blue"]the unlikely scenario of you getting fired because the alarm app failed[/COLOR].
Please do some research if you have any concerns about features included in this ROM
before flashing it! YOU are choosing to make these modifications, and if you point the finger at
me for messing up your device, I will laugh at you.
Features
ROM
Android 7.1.1 Nougat
Based on stock J510FNXXU2BRL1
De-odexed & de-knoxed
Heavily de-bloated
Powered by AetherAura
Introduced Google's night light
Sleekier wallpapers
Build.prop tweaks
Fluid UI
Better scrolling
Kernel
Rendering
Dalvik
Bit GPU
Video acceleration
Disable spamming loggers
And more!
Lighter apps and frameworks
OMC support
And more!
KERNEL
Based on J510FNXXU2BRB1 NN source
ARCH POWER
PowerSuspend
Adreno Idler
MSM Limiter
Custom Voltage Control
INTELLI THERMAL (thermal driver)
Simpler MSM THERMAL MONITOR
INTELLI PLUG (hotplug driver)
Faux Sound Control v3.6
Adaptive LMK
USB Fast Charge
Dynamic Fsync
TCP congestion algorithms
Advanced
Cubic
Westwood (default)
Vegas
Illinois
And more!
IO schedulers
Improved BFQ
FIOPS
SIO
SIO+
ZEN (default)
Tripndroid
And more!
Aether post-boot scripts
LMK values for fortuna
Disabled adaptive LMK by default
Ultra KSM
Power-oriented workqueues
CPU overclock frequencies
1248 MHz
1363 MHz
1401 MHz
GPU overclock frequencies
465 MHz
500 MHz
550 MHz
600 MHz
620 MHz
Samsung charger controls
Quad-core power savings
And more!
Screenshots
Supported variants
SM-G530HXX
SM-G530HXC
SM-G530M (flash the fortuna3g kernel release)
SM-G530BT
SM-G530FZ
SM-G530F
What's not working
Variant: SM-G530F
Bluetooth (toggles on and off when switched on)
All variants [unfixable]
Video recording (on some apps) (however, Instagram and SC are fully functional)
Manual focus on stock camera causes kernel panic
Installation instructions and downloads
Aether Lite R10
Aether Aura latest kernel release
Huge thanks to
@TenSeventy7 - Great help and support
@Kamin4ri - Great help and support
@mdmaher - Great help and support
@vin58 - HALs from AOSP
@itexpert.120 - Kernel optimizations
@prototype74 - Google's night light and help
@BlackMesa123 - Kernel optimizations
@corsicanu - Kernel optimizations
@Bulgaricus - Kernel optimizations
@SPARTANICUS - Kernel optimizations
@Chainfire - SuperSU
Like my work? Tap that "Thanks" button!
XDA:DevDB Information
[SE] [7.1.1] Aether Lite [G530X], ROM for the Samsung Galaxy Grand Prime
Contributors
CaelestisZ
Source Code: https://github.com/CaelestisZ/AetherAura
ROM OS Version: 7.x Nougat
ROM Kernel: Linux 3.10.x
ROM Firmware Required: Latest 5.x baseband
Version Information
Status: Beta
Created 2020-06-05
Last Updated 2020-06-15
Kernel Change-log:
Ascent
Selective fortuna drivers updated
Reduced CPU average load
Enabled ARCH_POWER
Reduced kernel overheat
Introduced PowerSuspend
Introduced MSM Adreno Idler
Introduced StateNotifier
Introduced MSM Limiter
Introduced Custom Voltage Control
Introduced lpClock
And several performance optimizations
BlueFlare
Undervolt for better compatibility
Implemented fast idling of CPU
Tune task-scheduler for power savings
Introduced USB fast-charge
TCP Westwood tune-up
Fixed headphone buttons
ClangorousSoulblaze
Introduced a simpler MSM thermal monitor
Introduced Intelli-plug hotplug driver
Introduced Faux sound control
Fixed RIL, Radio (now fully functional)
Added Knox SDP/DLP
DracoMeteor
Introduced LCD notify
Introduced Dynamic FSync and ASync
Enable Adaptive LMK
Disable CRC by default
Eternatus
Disable zRAM
Enable SSWAP
Merge J510FNXXU2BRB1 ramdisk
Merge Aether post-boot scripts
Enable TCP congestion algorithms
Advanced
Cubic
Westwood
Vegas
Illinois
And more!
Introduced IO Schedulers
Improved BFQ
FIOPS
SIO
SIO+
ZEN
Tripndroid
And more!
Properly enabled ARCH POWER & gentle fair sleepers
FleurCannon
Introduced INTELLI THERMAL driver
CPUfreq, CPUidle: implement -O3 optimizations
GigavoltHavoc
Disable loads of unnecessary configurations
MSM Adreno Idler: more aggressive
Boot on all 4 cores
Attempt at enhancing power efficiency
Re-enabled kernel tick rate to 300Hz
Default TCP congestion algorithm: Westwood
Default IO Scheduler: ZEN
Set writeback parameters
dirty_background_ratio = 10%
vm_dirty_ratio = 20%
And more!
HyperspaceFury
Introduced Ultra KSM
Implemented system-wide power-oriented workqueues
Introduced Samsung charger controls
Enable quad-core power savings
CPU overclock frequencies
1248 MHz
1363 MHz
1401 MHz
GPU overclock frequencies
465 MHz
500 MHz
550 MHz
600 MHz
620 MHz
And more!
ROM Change-log
5th June 2020
Android 7.1.1 Nougat
Based on stock J510FNXXU2BRL1
De-odexed & de-knoxed
Heavily de-bloated
Powered by AetherAura
Introduced Google's night light
Sleekier wallpapers
Lighter apps and frameworks
OMC support
And more!
15th June 2020
Bump to R10.AetherLite
Installer now detects variant and deploys appropriate files
Packed with the latest release of AetherAura (FleurCannon)
Lock screen security is now fully functional
De-bloated a little more
Added build.prop tweaks
Fluid UI
Better scrolling
Kernel
Rendering
Dalvik
Bit GPU
Video acceleration
Disable spamming loggers
And more!
Updated CSC/OMC version
Fixed bugs that persist only on the G530HXC
De-knoxed for real
Join us on Telegram to stay up to date with the latest releases.
Telegram group invite: G530* Project: Aether
P.S. I do undertake device support/feature requests, provided it is a G530* and you can wait!
Nice Job Bro!
Hope that rest of the bugs will get fixed quickly.
hey guys, this is doc. havent bothered to change my username yet. (and i guess xda wouldn't allow me anyway, i already changed my username once)
actually, bluetooth only works fully on fortuna3gdtv lol (and possibly any other non-XX/XC baseband variant, eg fortunalteub / G530M)
Kamin4ri said:
hey guys, this is doc. havent bothered to change my username yet. (and i guess xda wouldn't allow me anyway, i already changed my username once)
actually, bluetooth only works fully on fortuna3gdtv lol (and possibly any other non-XX/XC baseband variant, eg fortunalteub / G530M)
Click to expand...
Click to collapse
IIRC it works on fortuna3g perfectly too
AetherLite R10 is up!
Installation instructions and downloads
Reboot into custom recovery.
Flash AetherLite_R10.zip from here: Aether Lite R10
Want root access? Latest SuperSU: SuperSU
Reboot & Enjoy!
Make sure to uncheck "Diagnostic Data" in Setup Wizard or you will have signal issues!
Do not flash Magisk with this kernel as it causes overheating and battery issues. (Due to some conflicts with LMK and Magisk)
It's normal for your device to restart once when on the boot animation after flashing SuperSU. (don't conclude it's a bootloop if that happens)
Changes made
Installer now detects variant and deploys appropriate files
Packed with the latest release of AetherAura (FleurCannon)
Lock screen security is now fully functional
De-bloated a little more
Added build.prop tweaks
Fluid UI
Better scrolling
Kernel
Rendering
Dalvik
Bit GPU
Video acceleration
Disable spamming loggers
And more!
Updated CSC/OMC version
Fixed bugs that persist only on the G530HXC
De-knoxed for real
What does this R10 symbolises here
Hi I am little confuse over here after seeing ur named rom aether lite ; actually what does this R10 symbolises here , is it that this rom has been upgraded to android 10 ?
Thank you
AYUSH NETWORK said:
Hi I am little confuse over here after seeing ur named rom aether lite ; actually what does this R10 symbolises here , is it that this rom has been upgraded to android 10 ?
Thank you
Click to expand...
Click to collapse
R10 means 10th version.
Btw the it needs to be lot more compressed according to the standards
itexpert.120 said:
R10 means 10th version.
Click to expand...
Click to collapse
Bro doesn't it suitable , means that actually file size is to much greater thn what it seems to be build for android standard
AYUSH NETWORK said:
Bro doesn't it suitable , means that actually file size is to much greater thn what it seems to be build for android standard
Click to expand...
Click to collapse
Maybe because it is aroma installer and tw-n???
Hope well
cpt_Sherman said:
Maybe because it is aroma installer and tw-n???
Click to expand...
Click to collapse
Yeah but lot's of more custom roms are there which are being pre-installed aroma features and many other lot's of valuable features ; but this is rom is what mainly creates some less advantage for download due to its large file size .
Thank you
AYUSH NETWORK said:
Yeah but lot's of more custom roms are there which are being pre-installed aroma features and many other lot's of valuable features ; but this is rom is what mainly creates some less advantage for download due to its large file size .
Thank you
Click to expand...
Click to collapse
Do me a favour and list some of the ROMs (you're talking about, probably link me to it) running Touchwiz N released for any device having the zip size less than this one? (dw I've de-bloated it leaving out all the essential features in it and added a few too)
Also, R10 features an Installer that deploys fixes and the kernel for each supported variant. (HXX/HXC/F/FZ/BT)
It's not an aroma installer that I've included.
Then again, the /system size of the zip is the same as that of our beloved stock lollipop.
Boot loop (G530BT)
EDIT: Works now, don't install supersu with twrp
AYUSH NETWORK said:
Yeah but lot's of more custom roms are there which are being pre-installed aroma features and many other lot's of valuable features ; but this is rom is what mainly creates some less advantage for download due to its large file size .
Thank you
Click to expand...
Click to collapse
Bro, this is not AOSP Rom, it is samsung's tw and nougat on that. The Stock ROM for Grand prime is roughly 600-900MB. Compared to this rom, this is much lighter and better. Also, this rom is not a build to begin with. This is a ported ROM from other samsung device.
Does this rom support OTA updates or it has been updates over air
Bro I want to ask something about this rom , is it support OTA updates ; does it get updated by software updates or u frequently update this rom with on time air upadtes ??
---------- Post added at 06:35 AM ---------- Previous post was at 06:28 AM ----------
Bro just u can please tell me in brief about it battery performance and task management ability to stand battery and stable performance of overall android for a particular time period ??
FrostyAndroid said:
Boot loop (G530BT)
EDIT: Works now, don't install supersu with twrp
Click to expand...
Click to collapse
@Kamin4ri tested SuperSU on G530BT, and it doesn't cause a boot loop in G530BT or in any of the supported variants.
It's normal for your device to restart once when on the boot animation after flashing SuperSU. (don't conclude it's a bootloop if that happens)
Next time, be patient.
Please refrain from posting messages with utmost surety when you're actually not sure about it.
New kernel release is up!
Installation instructions and downloads
Reboot into custom recovery.
Make sure you're on Aether Lite R10.
Flash AetherAura_GigavoltHavoc*.zip for your variant from here: AetherAura releases
Want root access? Latest SuperSU: SuperSU
Reboot & Enjoy!
Do not flash Magisk with this kernel as it causes overheating and battery issues. (Due to some conflicts with LMK and Magisk)
It's normal for your device to restart once when on the boot animation after flashing SuperSU. (don't conclude it's a bootloop if that happens)
Changes made
Bump to version: GigavoltHavoc
Disable loads of unnecessary configurations
MSM adreno idler: slightly more aggressive
Boot on all available cores
Attempt at enhancing power efficiency
Re-enabled kernel tick rate to 300Hz
Set writeback parameters
dirty_background_ratio = 10%
vm_dirty_ratio = 20%
Set WESTWOOD as default TCP
Set ZEN as default IO Scheduler
And more!
Like my work? Tap that "Thanks" button!
Are you taking requests?