Bootloader = Oxygen
Bootloader = locked
USB Debug = off
Display = Black without panel light
Because of the screen can't enter the menu to unlock bootloader or install TWRP
Problem:
The phone worked before i flashed a firmware with Test Point method to remove a forgotten password. So, i flashed this firmware from http://en.miui.com/thread-844022-1-1.html and followed all the steps by removing the emmc_appsboot.mbn from the firmware with one from the MI Max 2. The problem is that after turn on the phone, i don't see anything, even the display panel has no light, is blank black, but if i wait few minutes after flashing, the phone boot in the setup menu and i hear the sounds. I can hear the sounds when charging and when phone boots up. Keep in mind that before flashing the rom when i tried to enter in fastboot or stock recovery, i didn't saw the fastboot logo or recovery menu. So, is there something wrong? Is there a file in the firmware that needs to be replaced with another one? A display firmware/driver missing? Can somebody upload a firmware for Oxygen bootloader and will all the instructions? Or is there any solution to unlock bootloader to install Twrp with a custom firmware? Any help is appreciated.
Dou you do this?
5. Run "writeselparts" application in "unbrick" folder and wait... This'll flash emmc_appsboot.mbn from Mi Max 2. When succeed, you'll get this message:...
I follow the same http://en.miui.com/thread-844022-1-1.html and everything is ok.
Hi, thanks for reply. Yes i did that. The phone boots up, i have sound but screen is black.
Any solutions?? i'm in the same situation..
NegreiAdrian said:
Bootloader = Oxygen
Bootloader = locked
USB Debug = off
Display = Black without panel light
Because of the screen can't enter the menu to unlock bootloader or install TWRP
Problem:
The phone worked before i flashed a firmware with Test Point method to remove a forgotten password. So, i flashed this firmware from thread-844022-1-1.html and followed all the steps by removing the emmc_appsboot.mbn from the firmware with one from the MI Max 2. The problem is that after turn on the phone, i don't see anything, even the display panel has no light, is blank black, but if i wait few minutes after flashing, the phone boot in the setup menu and i hear the sounds. I can hear the sounds when charging and when phone boots up. Keep in mind that before flashing the rom when i tried to enter in fastboot or stock recovery, i didn't saw the fastboot logo or recovery menu. So, is there something wrong? Is there a file in the firmware that needs to be replaced with another one? A display firmware/driver missing? Can somebody upload a firmware for Oxygen bootloader and will all the instructions? Or is there any solution to unlock bootloader to install Twrp with a custom firmware? Any help is appreciated.
Click to expand...
Click to collapse
Hey, which ROM were you using before the issue? Did your phone came with the oxygen bootloader, or you flashed it accidentally?
Hi guys! Who have official firmware for Mi 5X Oxygen? Maybe after flash official developer version screen will back?
DeeJay_145 said:
Hi guys! Who have official firmware for Mi 5X Oxygen? Maybe after flash official developer version screen will back?
Click to expand...
Click to collapse
That’s exactly what I was thinking (sort of). But instead of using their oxygen modified rom, I was hoping to find someone with a oxygen bootloader to do a entire partition backup (not just the ones that twrp allows) so I can inspect each one and check what else they changed to make it work. I still think that they change other partitions than the bootloader (emmc_appsboor)
matheusbittencourt said:
That’s exactly what I was thinking (sort of). But instead of using their oxygen modified rom, I was hoping to find someone with a oxygen bootloader to do a entire partition backup (not just the ones that twrp allows) so I can inspect each one and check what else they changed to make it work. I still think that they change other partitions than the bootloader (emmc_appsboor)
Click to expand...
Click to collapse
have you backup modified rom from oxygen device?
DeeJay_145 said:
have you backup modified rom from oxygen device?
Click to expand...
Click to collapse
No, I'm still trying to find someone that have the 5x with oxygen bootloader to dump the images.
i have one device same with your problem dont have any idea to fix
same problem for my mi phone too... how is not solved yet?!
untill now dont have any solution for it
yes i have black screen issues too... there is sounds when charging, and three buttons below showing lights, plug in to my computer and detected as Mi5X MTP in My Computer
any solution?
maybe someone has figured it out?
matheusbittencourt said:
Hey, which ROM were you using before the issue? Did your phone came with the oxygen bootloader, or you flashed it accidentally?
Click to expand...
Click to collapse
In my case, I was using a ROM MIUI.EU, when I updated via OTA, the phone was left with the black screen.
how did you fix the black screen?
i updated miui.eu via ota, i have black screen everywhere, including twrp and fastboot!! Never saw something like this!
5x with oxygen bootloader
matheusbittencourt said:
No, I'm still trying to find someone that have the 5x with oxygen bootloader to dump the images.
Click to expand...
Click to collapse
I have one.
nemo50 said:
I have one.
Click to expand...
Click to collapse
May i have your firmware sir?
same problem Did you find any solution?
Solution is: backup all your data with adb and scrcpy (hope you left adb enabled), then flash the latest China stable with MI flash. At that point flash latest xiaomi.eu stable
Related
The situation is that I just bought the K20 Pro. Then i unlock and flash by miflash with Global Rom via this thread then the device has bricked and has the message "This MIUI version can't be installed on this device".
Tried boot into recovery but the TWRP has gone and the bootloader has been locked.
Flash back to China Rom by miflash is doesn't work either, help me please, i don't know what to do now, i tried every thing i can.
:crying::crying:
P/s: Sorry for my bad English.
dsown said:
The situation is that I just bought the K20 Pro. Then i unlock and flash by miflash with Global Rom via this thread then the device has bricked and has the message "This MIUI version can't be installed on this device".
Tried boot into recovery but the TWRP has gone and the bootloader has been locked.
Flash back to China Rom by miflash is doesn't work either, help me please, i don't know what to do now, i tried every thing i can.
:crying::crying:
P/s: Sorry for my bad English.
Click to expand...
Click to collapse
just calm down and try to unlock bootloader again by (miflash_unlock) then install in computer (adb-setup-1.4.3) then keep press on power and volume down button for fastboat then open miflash (version=2017.4.25.0) and connect your phone and press refresh to see your phone on list then download India Stable Firmwares version in same thread you mention and unzip the file and unzip the result file then you will see 12 file (images/ flash_all.bat .....) and in miflash choose the file and press flash and wait... when its done your phone will work but will give account is locked just connect with wifi and write your micloud password and done .
dsown said:
The situation is that I just bought the K20 Pro. Then i unlock and flash by miflash with Global Rom via this thread then the device has bricked and has the message "This MIUI version can't be installed on this device".
Tried boot into recovery but the TWRP has gone and the bootloader has been locked.
Flash back to China Rom by miflash is doesn't work either, help me please, i don't know what to do now, i tried every thing i can.
:crying::crying:
P/s: Sorry for my bad English.
Click to expand...
Click to collapse
Miflash only works on an unlocked bootloader. It appears that you have a Chinese Model and you just did what was supposed to be avoided. You should get accustomed to Miflash moving forward. Never use Flash_All_Lock while cross flashing China/Global roms. You'll have to wait to unlock your Bootloader now and post that flash the China rom to get back. If any time you wish to move to the India rom, either use a twrp recovery or just use Flash_All while using the fastboot image which should eventually avoid locking the bootloader
Sent from my Redmi K20 Pro using Tapatalk
dsown said:
The situation is that I just bought the K20 Pro. Then i unlock and flash by miflash with Global Rom via this thread then the device has bricked and has the message "This MIUI version can't be installed on this device".
Tried boot into recovery but the TWRP has gone and the bootloader has been locked.
Flash back to China Rom by miflash is doesn't work either, help me please, i don't know what to do now, i tried every thing i can.
:crying::crying:
P/s: Sorry for my bad English.
Click to expand...
Click to collapse
1. if you can still enter fastboot mode, there is a possibility that you can do TWRP flashing again (the TWRP version must be correct so that the data on the cellphone can be read properly) / Flashing from the PC (if you are lucky, the flashing will work properly without any problem or you can bypass the bootloader locked using software or something else). [make sure ROM version must be appropriate because this is very crucial]
2. You can try using the test point method (EDL / Emergency Download Mode) [This method is usually used if your K20Pro is constrained by Hardbrick due to ARB4] , but this method requires you to open the case / body behind your K20Pro. and I cannot guarantee that the flashing process will succeed easily because in some cases if the K20Pro is detected damage / error due to ARB4, then you are required to have an Authorized Mi Account. I might be able to help you remotely, if you agree with the risks & requirements in the flashing process (I can lend my account, but it's not free).
Hi All, I did the same thing - whoever build the UI for MiFlash should be shot - why default that selection to something that will be undesirable!!?
Anyway, i tried to flash indian rom and forgot to set to Clean All, it locked the bootloader.
So i now have redmi recovery and Fastboot options only on phone.
Have tried fastboot + miflash but all options (now with Chinese rom) - says Erase Boot Error.
Tried MiAssistant + Mi PC Suite - it is not detecting the phone in either MiAssistant recovery mode nor Fastboot mode. what is weird is the phone and connector animation on phone is correctly depicting when it is plugged in/unplugged. But the PC suite isnt detecting the device.
Soft bricked - *sigh.... any help will be greatly appreciated from the community
BTW i am more worried that the phone will run out of battery and never wake up once battery drains completely as it is in bootloop into Redmi recovery and can't be turned off (someone tell me how!?) - I don't see the phone respond to charging in any state... : (
Can you still reach fastboot? If so you can unlock phone again and flash TWRP using ADB. After that boot straight into TWRP and connect it to your computer, internal SD storage should then automatically mount. Drag and drop ROM .zip into internal storage, use TWRP file manager to move it out of the data folder and do a default wipe using TWRP. Then flash .zip ROM (for example xiaomi.eu stable) and you should be back in business. Please let me know if you need any files like working recovery image and further instructions.
I had some trouble with my TWRP recovery yesterday, flashed it on unlocked bootloader with Chinese stable ROM installed, on reboot out of fastboot it boots straight into ROM and overwrites the TWRP recovery with default recovery. I fixed it by flashing recovery again, boot straight into it and flash xiaomi.eu stable, now recovery is TWRP and does not get overwritten.
hippo2s said:
Hi All, I did the same thing - whoever build the UI for MiFlash should be shot - why default that selection to something that will be undesirable!!?
Anyway, i tried to flash indian rom and forgot to set to Clean All, it locked the bootloader.
So i now have redmi recovery and Fastboot options only on phone.
Have tried fastboot + miflash but all options (now with Chinese rom) - says Erase Boot Error.
Tried MiAssistant + Mi PC Suite - it is not detecting the phone in either MiAssistant recovery mode nor Fastboot mode. what is weird is the phone and connector animation on phone is correctly depicting when it is plugged in/unplugged. But the PC suite isnt detecting the device.
Soft bricked - *sigh.... any help will be greatly appreciated from the community
BTW i am more worried that the phone will run out of battery and never wake up once battery drains completely as it is in bootloop into Redmi recovery and can't be turned off (someone tell me how!?) - I don't see the phone respond to charging in any state... : (
Click to expand...
Click to collapse
Read this https://forum.xda-developers.com/k20-pro/help/destroyed-error-fastboot-locked-t3946012
And this
https://forum.xda-developers.com/k20-pro/help/k20-pro-bricked-t3951531
You're probably going to have to open up the phone and pay $20 for someone to use their authorised account to flash an official ROM whilst remoting in to your PC.
322Reznov said:
Can you still reach fastboot? If so you can unlock phone again and flash TWRP using ADB. After that boot straight into TWRP and connect it to your computer, internal SD storage should then automatically mount. Drag and drop ROM .zip into internal storage, use TWRP file manager to move it out of the data folder and do a default wipe using TWRP. Then flash .zip ROM (for example xiaomi.eu stable) and you should be back in business. Please let me know if you need any files like working recovery image and further instructions.
I had some trouble with my TWRP recovery yesterday, flashed it on unlocked bootloader with Chinese stable ROM installed, on reboot out of fastboot it boots straight into ROM and overwrites the TWRP recovery with default recovery. I fixed it by flashing recovery again, boot straight into it and flash xiaomi.eu stable, now recovery is TWRP and does not get overwritten.
Click to expand...
Click to collapse
Some great ideas - Just tried to unlock bootloader - This device came pre-unlocked so the device is tied to the seller's account.
I have unlock permission - but unlocker say device is not bound to my account matching my assumptions - anyone know what's the best way to re-claim ownership? Especially when I can't get into ROM at all?
hippo2s said:
Some great ideas - Just tried to unlock bootloader - This device came pre-unlocked so the device is tied to the seller's account.
I have unlock permission - but unlocker say device is not bound to my account matching my assumptions - anyone know what's the best way to re-claim ownership? Especially when I can't get into ROM at all?
Click to expand...
Click to collapse
My comment was meant for OP but I hoped it would help you as well! I am personally not well informed about the Xiaomi / Redmi ownership situation when the seller unlocked the phone.. maybe you can contact them and get a corresponding password to the account, it has been the solution I have seen offered here. Maybe the emergency flash solution from Robbo.5000 works?
I just got this phone a week now and was only able to unlock and flash yesterday, I was aware of the ownership problem thanks to this forum so I bought the sealed CN version. Hope you figure it out!
Thanks guys. I am going for the Test Point solution - have made contact with the Russian tech the others did and made an appointment. I just have to pretend to be Jerry Rig before then and open her up! Fingers crossed!
322Reznov said:
Can you still reach fastboot? If so you can unlock phone again and flash TWRP using ADB. After that boot straight into TWRP and connect it to your computer, internal SD storage should then automatically mount. Drag and drop ROM .zip into internal storage, use TWRP file manager to move it out of the data folder and do a default wipe using TWRP. Then flash .zip ROM (for example xiaomi.eu stable) and you should be back in business. Please let me know if you need any files like working recovery image and further instructions.
I had some trouble with my TWRP recovery yesterday, flashed it on unlocked bootloader with Chinese stable ROM installed, on reboot out of fastboot it boots straight into ROM and overwrites the TWRP recovery with default recovery. I fixed it by flashing recovery again, boot straight into it and flash xiaomi.eu stable, now recovery is TWRP and does not get overwritten.
Click to expand...
Click to collapse
You need yo flash magisk after you flash twrp if you want to run regular miui, to prevent it from overwriting the recovery. Its the same on poco and all xiaomi phones
Mooatreides said:
You need yo flash magisk after you flash twrp if you want to run regular miui, to prevent it from overwriting the recovery. Its the same on poco and all xiaomi phones
Click to expand...
Click to collapse
Ah alright thank you for the info! This is my first ever Xiaomi / Redmi phone haha
dsown said:
The situation is that I just bought the K20 Pro. Then i unlock and flash by miflash with Global Rom via this thread then the device has bricked and has the message "This MIUI version can't be installed on this device".
Tried boot into recovery but the TWRP has gone and the bootloader has been locked.
Flash back to China Rom by miflash is doesn't work either, help me please, i don't know what to do now, i tried every thing i can.
:crying::crying:
P/s: Sorry for my bad English.
Click to expand...
Click to collapse
Did you flash the global rom on an existing running Chinese rom or on an empty device (formatted)? Just for myself cuz I'm not sure whether to unlock and then unable to relock. Thanks.
pungky771 said:
1. if you can still enter fastboot mode, there is a possibility that you can do TWRP flashing again (the TWRP version must be correct so that the data on the cellphone can be read properly) / Flashing from the PC (if you are lucky, the flashing will work properly without any problem or you can bypass the bootloader locked using software or something else). [make sure ROM version must be appropriate because this is very crucial]
2. You can try using the test point method (EDL / Emergency Download Mode) [This method is usually used if your K20Pro is constrained by Hardbrick due to ARB4] , but this method requires you to open the case / body behind your K20Pro. and I cannot guarantee that the flashing process will succeed easily because in some cases if the K20Pro is detected damage / error due to ARB4, then you are required to have an Authorized Mi Account. I might be able to help you remotely, if you agree with the risks & requirements in the flashing process (I can lend my account, but it's not free).
Click to expand...
Click to collapse
My k20 pro is hard bricked and i cant get fast boot or any thing it wont even come on. Assistance please
hippo2s said:
Thanks guys. I am going for the Test Point solution - have made contact with the Russian tech the others did and made an appointment. I just have to pretend to be Jerry Rig before then and open her up! Fingers crossed!
Click to expand...
Click to collapse
Could you please point me to the person you have contacted?
I'm in EDL for about two weeks now, unable to solve it by different means (seller sais 'send it back', which I'm not goong to do; S-unlock has the service unavailable, even though I've paid them and the guy I contacted there tried through TW to no avail, waiting for a 'money back' now)..
Hi guys!
May I know if anybody here experienced black screen ? Screen has no image to display. Backlight is working, Led light is working when charging, fingerprint vibrates as well when A2 is turned on. I have tried replacing LCD display but black screen persists. What do you think is the problem?
Sent from my Mi 9 SE using Tapatalk
I have the same problem!!!! I try flash rom again but it persists
Yesterday it happened to me also.
The phone is working, the touch is working, but the lcd is black.
I even managed to recieve a call. Tried to restart the phone but its still black screen with working touch.
I can't find any solution...
Anybody found a solution??
My MI A2 is in black screen after updated to Wayne V11.0.6.0.PDCCNXM 20200509.
Tried to flash again, the screen didn't even turned on anymore, then used an UNBRICK WAYNE XIAOMI MI6X and it's back to black screen, been like this for 4 days now, should I start looking for a new phone? :crying:
Serial number: 23e3c4ee
Codename: wayne
Bootloader: locked
Anti version: 4
ROM: Wayne V11.0.6.0.PDCCNXM 20200509.
When I flash the ROM again, takes 100, 200 seconds only, and didn't change anything.
RiFeee said:
Anybody found a solution??
My MI A2 is in black screen after updated to Wayne V11.0.6.0.PDCCNXM 20200509.
Tried to flash again, the screen didn't even turned on anymore, then used an UNBRICK WAYNE XIAOMI MI6X and it's back to black screen, been like this for 4 days now, should I start looking for a new phone? :crying:
Serial number: 23e3c4ee
Codename: wayne
Bootloader: locked
Anti version: 4
ROM: Wayne V11.0.6.0.PDCCNXM 20200509.
When I flash the ROM again, takes 100, 200 seconds only, and didn't change anything.
Click to expand...
Click to collapse
stop stressing . you have ARB4 so just flash a custom rom ...or flash only the LASTEST STOCK ROM ...you didn't listen and tried to flash another think ...so your phone went to hardbrick edl mode
your phone is fine it is just in a timeout edl mode
the only way to fully rescue it is by physically forcing testpoint then flashing LATEST FASTBOOT STOCK ...this time listen or stay on black screen
KevMetal said:
stop stressing . you have ARB4 so just flash a custom rom ...or flash only the LASTEST STOCK ROM ...you didn't listen and tried to flash another think ...so your phone went to hardbrick edl mode
your phone is fine it is just in a timeout edl mode
the only way to fully rescue it is by physically forcing testpoint then flashing LATEST FASTBOOT STOCK ...this time listen or stay on black screen
Click to expand...
Click to collapse
Already did it and gets worse, if I flash the latest fastboot Stock ROM really becomes a brick, to de point of not even the screen turns on and stay on edl mode forever.
RiFeee said:
Already did it and gets worse, if I flash the latest fastboot Stock ROM really becomes a brick, to de point of not even the screen turns on and stay on edl mode forever.
Click to expand...
Click to collapse
because you are trying to downgrade
what you need to do is flash the LATEST chinese fastboot stock rom of Wayne or it will never work
you need to flash it with edl and miflash ( LATEST BETA)
you keep on thinking you can flash any stock rom but you can't ......
if you try to flash any stock rom older than the last stock rom you flashed it will never boot and keep going back to edl blackscreen
if you DON'T open your phonr and short the test point miflash will timeout or give errors and device wont boot
open your phone with screwdriver and flash the VERY latest chinese fastboot rom with latest miflash beta
KevMetal said:
because you are trying to downgrade
Click to expand...
Click to collapse
Already tried to downgrade, upgrade, change the type of rom, original, custom, and nothing worked
RiFeee said:
Already tried to downgrade, upgrade, change the type of rom, original, custom, and nothing worked
Click to expand...
Click to collapse
that is your problem ...you think you can get out of this without paying the price ..you cant
do what I told you ...in the posts before
KevMetal said:
because you are trying to downgrade
what you need to do is flash the LATEST chinese fastboot stock rom of Wayne or it will never work
you need to flash it with edl and miflash ( LATEST BETA)
you keep on thinking you can flash any stock rom but you can't ......
if you try to flash any stock rom older than the last stock rom you flashed it will never boot and keep going back to edl blackscreen
if you DON'T open your phonr and short the test point miflash will timeout or give errors and device wont boot
open your phone with screwdriver and flash the VERY latest chinese fastboot rom with latest miflash beta
Click to expand...
Click to collapse
KevMetal said:
that is your problem ...you think you can get out of this without paying the price ..you cant
do what I told you ...in the posts before
Click to expand...
Click to collapse
What a heck are you talking about?
Already did everything with Mi flash, forced edl mode by point test, saw like 300 tutorials, for Mi A2, Mi 6x.
What I needed was a verified Mi account to unlock and flash with no problems
RiFeee said:
What a heck are you talking about?
Already did everything with Mi flash, forced edl mode by point test, saw like 300 tutorials, for Mi A2, Mi 6x.
What I needed was a verified Mi account to unlock and flash with no problems
Click to expand...
Click to collapse
well if you had followed any of mine or listened carefully to what I'm telling you , your device would have booted already ... but continue in the same manner since you think my help is gibberish .
you don't need an account to flash your device ...
KevMetal said:
well if you had followed any of mine or listened carefully to what I'm telling you , your device would have booted already ... but continue in the same manner since you think my help is gibberish .
you don't need an account to flash your device ...
Click to expand...
Click to collapse
I already did, tried all the tutorials from 2018 to last month. The phone bootloader is locked and for some reason I can't unlock it, tried a dozen of different approaches, recovery's, flashings, ADB and everything.
Always ends in two ways, black screen with back light on (some sounds work and keeps in the lock login screen) or dead stuck in permanent EDL mode.
My phone still not working. Maybe its because of the busted display IC.
Hi,
Recently purchased a Mi 9 Global version, got the OTA update to MIUI 11, and everything was well. It is a superb phone, but I like to have root on my phones (mostly for Adblocking and System2, better control overall). I tried to install TWRP (custom version for Mi9) because I wanted to install Magisk/Root or try a different rom eventually. Anyway... I made a huge mistake. After trying to reboot, I noticed things had gone wrong, and was stuck in a boot loop. I guess I panicked and tried to flash the phone back to the latest global MIUI rom (Version 11, Android 10, from official site), using the Xiaomi Flash App but I did not uncheck the "clean and lock bootloader" checkbox on the bottom right of the app, which is somehow enabled by default. The flash failed at that time, for unknown reason, but it seems like it succeeded in locking my bootloader, with an empty partition, except for fastboot access and Mi Recovery module. I have to admit I've always been pretty lucky with all my previous flashes on other devices, and I guess I got a little careless. That was pretty stupid of me, in retrospect.
Since then, I am stuck in either Mi Recovery or Fastboot, and it seems that my originally Global Mi 9 with unlock bootloader has now a locked bootloader. Any attempt at either using the Xiaomi Flash utility gives me an error message ("Erase boot error"), and if I boot into Fastboot and try to flash TWRP, I get the "Remote:Erase is not allowed in Lock State" error.
From what I understand, my options are pretty limited now. The phone is still powered on, stuck in Recovery mode and rebooting every 5 or 10 minutes by itself (probably a way to avoid screen burn-in?), but I can't seem to be able to shut it down in anyway, as there are no fastboot commands to send a shutdown signal. And no matter what button combination I press, the phone always ends up rebooting.
I tried the Xiaomi Unlocker utility, but it needs the phone to be out of recovery to check the credentials binding the phone to my account. All data on the phone has been wiped already, so that's not an option. Two options I have seen :
1. Open the battery cover (required a heat gun and risky), to short some pins and try to flash while there is a short to circumvent the security. I'm not that brave yet, and since the phone is still running and has probably about 80% battery, I don't want to use a heat gun on the device.
2. Shady stuff involving paying 30 or 40 Euros to a random guy who can somehow make everything work magically by remotely logging in on my computer via Teamviewer (Not happening in a million years).
I'm wondering if there is an alternative, other than bringing the device to an official Xiaomi store (I'm in Bangkok and they do have one official shop at Fortune Town), but even then, I don't know if they'll just tell me I got myself an expensive paperweight.
Any help/insight regarding this issue would be much, much appreciated!
Have you tried to press and hold power+vol down when your device reboots? Just before it turns on.
g_seva said:
Have you tried to press and hold power+vol down when your device reboots? Just before it turns on.
Click to expand...
Click to collapse
Every possible combination on reboot will either bring me to Fastboot or Mi Recovery. I have wiped the data partition, there is no OS on the phone as of now.
Twomby said:
Every possible combination on reboot will either bring me to Fastboot or Mi Recovery. I have wiped the data partition, there is no OS on the phone as of now.
Click to expand...
Click to collapse
So xiaomi unlock utility can't unlock bootloader in fastboot?
May be try to use xiaomitool v2.
g_seva said:
So xiaomi unlock utility can't unlock bootloader in fastboot?
May be try to use xiaomitool v2.
Click to expand...
Click to collapse
Xiaomitool V2 is completely useless. The "My phone is bricked" option is not implemented, and I cannot boot into the OS, unfortunately.
To enter fastboot mode, long press the volume down key and the power key. Then unlock bootloader with Xiaomi app.
zahdekar said:
To enter fastboot mode, long press the volume down key and the power key. Then flash stock rom.
Click to expand...
Click to collapse
I have managed to enter fastboot mode, as described in my initial post. The problem is that when I try to flash, I get the following error: "Flashing not allowed in lock state".
Twomby said:
Xiaomitool V2 is completely useless. The "My phone is bricked" option is not implemented, and I cannot boot into the OS, unfortunately.
Click to expand...
Click to collapse
Yep, but it has unlock option in the normal mode and it use scripts made by tool developer, so it worth to try.
g_seva said:
Yep, but it has unlock option in the normal mode and it use scripts made by tool developer, so it worth to try.
Click to expand...
Click to collapse
From what I understand, the "normal mode" needs the tool to be able to access the OS while it's running. I don't have an OS. I will give it a shot tomorrow (3 AM here, exhausted, and don't want to boot into Windows again!), but my hopes are not so high. Anyway, thanks for the help, much appreciated! Will let you know what happens! Cheers!
https://forum.xda-developers.com/Mi-9/how-to/unbrick-mi9-bootloader-locked-destroyed-t3924966/amp/
maybe it will help
zahdekar said:
https://forum.xda-developers.com/Mi-9/how-to/unbrick-mi9-bootloader-locked-destroyed-t3924966/amp/
maybe it will help
Click to expand...
Click to collapse
I've stumbled upon this link earlier today. But it's 404 on my end. Can you access it from where you are? Thanks!
http://c.mi.com/thread-2251372-1-1.html
This is on page 4
zahdekar said:
http://c.mi.com/thread-2251372-1-1.html
This is on page 4
Click to expand...
Click to collapse
Thanks. Tried it, but using these commands only cause a reboot, to recovery mode again. Thanks again for your kind help!
Twomby said:
Thanks. Tried it, but using these commands only cause a reboot, to recovery mode again. Thanks again for your kind help!
Click to expand...
Click to collapse
I have the same problem! "The system has been destroyed" (((
And mi unlock tool not work abount 2 days (authorization not passes)
https://forum.xda-developers.com/Mi-9/help/help-bricked-mi-9-t3921980/page2
The old version of miunlock is working ti unlock bootloader.
zahdekar said:
https://forum.xda-developers.com/Mi-9/help/help-bricked-mi-9-t3921980/page2
The old version of miunlock is working ti unlock bootloader.
Click to expand...
Click to collapse
Unfortunately, this is not true. I have downloaded an old version of Mi Unlock (2.2.406.5), which is supposed to work with Fastboot mode. The result is "Couldn't unlock --> Please download the latest version". And the latest version needs to access the OS to verify the Mi account credentials. I don't have an OS installed. So this won't work. Thanks for the suggestion though!
Twomby said:
Unfortunately, this is not true. I have downloaded an old version of Mi Unlock (2.2.406.5), which is supposed to work with Fastboot mode. The result is "Couldn't unlock --> Please download the latest version". And the latest version needs to access the OS to verify the Mi account credentials. I don't have an OS installed. So this won't work. Thanks for the suggestion though!
Click to expand...
Click to collapse
Hello @Twomby did you managed to get it working it the end?
Same issue here
Hi,
I am encouraging the same issue. Does someone found a solution to this?
tago4ever said:
Hi,
I am encouraging the same issue. Does someone found a solution to this?
Click to expand...
Click to collapse
I came across this Mi8 thread, not sure if it's possible on the Mi9, but he seems to have been able to flash it through EDL mode, you might ask him the question: https://xiaomi.eu/community/threads/mi-8-bricked-from-nowhere.55723/#post-543605
There's also this Mi9 thread: https://forum.xda-developers.com/Mi-9/how-to/unbrick-mi9-bootloader-locked-destroyed-t3924966
hey. Im hoping i can get some help. i just purchased the Chinese Version of the Mi 11, i waited a week and just unlocked the bootloader so decided to flash the Global Rom. However, things went wrong and now im stuck with a black screen. I can NOT get into recovery, but i do hear the devices connecting when i plug it in. I was on the Chinese Version 12.5.9.0. I tried flashing the Global Version 12.0.22.0, the when it i got stuck on the black screen. I tried to do research on it but can not figure it out for the life of me. Please, Need Help.. Thanks in advance. Bless..!!
Is it recognized in the computer?
Are you able to use Mi Flash Tool?
Have you eliminated the possibility of screen malfunction?
LowaEastSide said:
hey. Im hoping i can get some help. i just purchased the Chinese Version of the Mi 11, i waited a week and just unlocked the bootloader so decided to flash the Global Rom. However, things went wrong and now im stuck with a black screen. I can NOT get into recovery, but i do hear the devices connecting when i plug it in. I was on the Chinese Version 12.5.9.0. I tried flashing the Global Version 12.0.22.0, the when it i got stuck on the black screen. I tried to do research on it but can not figure it out for the life of me. Please, Need Help.. Thanks in advance. Bless..!!
Click to expand...
Click to collapse
If you can't access on your recovery... It's bricked. Are you sure to have flash the good ROM ? When you have this problem, it's due to a bad ROM flashed or corrupted Data / Download (Bad CRC/MD5) flashed under MiFlash on Fastboot Mode.
1/ Try combinaison : POWER + "-" or POWER + "+" with 5 seconds press
2/ Plug your Phone on your computer, launch Xiaomi Unlock (show device ? Locked/Unlocked Status ?)
3/ Plug your Phone on your computer, MiFlash (show device ? Locked/Unlocked Status ?)
4/ Plug your Phone on your computer, try "XiaoMiTool V2" for trying Unbrick
Pho3nX said:
If you can't access on your recovery... It's bricked. Are you sure to have flash the good ROM ? When you have this problem, it's due to a bad ROM flashed or corrupted Data / Download (Bad CRC/MD5) flashed under MiFlash on Fastboot Mode.
1/ Try combinaison : POWER + "-" or POWER + "+" with 5 seconds press
2/ Plug your Phone on your computer, launch Xiaomi Unlock (show device ? Locked/Unlocked Status ?)
3/ Plug your Phone on your computer, MiFlash (show device ? Locked/Unlocked Status ?)
4/ Plug your Phone on your computer, try "XiaoMiTool V2" for trying Unbrick
Click to expand...
Click to collapse
thank you for reaching out to me, however, i tried the combo you suggested, but its stuck on the Black screen. but it does connect to the computer. i also tried the miflash tools, and im getting the red Bar.
Kenora_I said:
Is it recognized in the computer?
Are you able to use Mi Flash Tool?
Have you eliminated the possibility of screen malfunction?
Click to expand...
Click to collapse
yes all of the above friend.
it connects to com
and its a brand new devices, i just unlocked the bootloader and was in the process of flashing the Global EU when everything went wrong.
now its stuck in a black screen, "EDL". So Upset..!!
LowaEastSide said:
yes all of the above friend.
it connects to com
and its a brand new devices, i just unlocked the bootloader and was in the process of flashing the Global EU when everything went wrong.
now its stuck in a black screen, "EDL". So Upset..!!
Click to expand...
Click to collapse
You'll have to pay someone to remote in to reflash the rom onto your phone if its stuck in EDL mode, i had the same issue when i flash and clean lock as well by accident and my phone got stuck in edl mode and this guy managed to fix my device (its costs 2500 Rub which was around £26 for me)
LowaEastSide said:
yes all of the above friend.
it connects to com
and its a brand new devices, i just unlocked the bootloader and was in the process of flashing the Global EU when everything went wrong.
now its stuck in a black screen, "EDL". So Upset..!!
Click to expand...
Click to collapse
i also spent Hours trying to flash it back with the miflash tool and continue to get HELLO POCKET Error plus a few other things it keep saying. Basically getting red bar error. and the coms plus drivers are downloaded correctly. i also tried all my ports. SMH.
skyler13 said:
You'll have to pay someone to remote in to reflash the rom onto your phone if its stuck in EDL mode, i had the same issue when i flash and clean lock as well by accident and my phone got stuck in edl mode and this guy managed to fix my device (its costs 2500 Rub which was around £26 for me)
Click to expand...
Click to collapse
would you happened to have his info?
skyler13 said:
You'll have to pay someone to remote in to reflash the rom onto your phone if its stuck in EDL mode, i had the same issue when i flash and clean lock as well by accident and my phone got stuck in edl mode and this guy managed to fix my device (its costs 2500 Rub which was around £26 for me)
Click to expand...
Click to collapse
would you happend to have his info? and thanks for your reply and Help brother
LowaEastSide said:
would you happend to have his info? and thanks for your reply and Help brother
Click to expand...
Click to collapse
so you was stuck in a black screen as well?
LowaEastSide said:
so you was stuck in a black screen as well?
Click to expand...
Click to collapse
yeah let me grab his details (he's on telegram) and yeah i was stuck on a black screen too. he was able to remote onto my computer and fix the hello packet error or write error i was getting and was able to get the edl mode flash and my phone booted up afterwards
LowaEastSide said:
so you was stuck in a black screen as well?
Click to expand...
Click to collapse
His telegram is Authorized Xiaomi Account MOD EDIT: Link Removed just message him, he'll say yeah he'll fix it for 2500Rub over paypal and he'll get this fixed for you. he's a trusted guy, managed to fix my device within 20 minutes.
Yeah, I wouldn't endorse it but you can only get someone like that to fix it. Also, try paying half at the start and rest in the end cause ya don't wanna get scammed
LowaEastSide said:
hey. Im hoping i can get some help. i just purchased the Chinese Version of the Mi 11, i waited a week and just unlocked the bootloader so decided to flash the Global Rom. However, things went wrong and now im stuck with a black screen. I can NOT get into recovery, but i do hear the devices connecting when i plug it in. I was on the Chinese Version 12.5.9.0. I tried flashing the Global Version 12.0.22.0, the when it i got stuck on the black screen. I tried to do research on it but can not figure it out for the life of me. Please, Need Help.. Thanks in advance. Bless..!!
Click to expand...
Click to collapse
https://www.youtube.com/watch?v=V8xiNoWz-Yw Tried this ? This is for global but grab a chinese version and follow the install guide
skyler13 said:
His telegram is Authorized Xiaomi Account MOD EDIT: Link Removed just message him, he'll say yeah he'll fix it for 2500Rub over paypal and he'll get this fixed for you. he's a trusted guy, managed to fix my device within 20 minutes.
Click to expand...
Click to collapse
Listen, I would like to thank you for helping me out Brother. I was able to reach out to the person you recommend, however he took a few hours to respond back to be. By the time he did I already had some I found on YouTube do for me remotely as well. Only chargers me $40 US. Im pretty sure I would have been able to haggle him down but figured it was a fare price. He also was kind enough to flash the globle 12.5 ROM as well. On that note, would you know if I'll be able to receive OTA updates? Or will I have to install TWRP RECOVERY and flash the new updates when they come out.? Thanks again for your help brother.
LowaEastSide said:
hey. Im hoping i can get some help. i just purchased the Chinese Version of the Mi 11, i waited a week and just unlocked the bootloader so decided to flash the Global Rom. However, things went wrong and now im stuck with a black screen. I can NOT get into recovery, but i do hear the devices connecting when i plug it in. I was on the Chinese Version 12.5.9.0. I tried flashing the Global Version 12.0.22.0, the when it i got stuck on the black screen. I tried to do research on it but can not figure it out for the life of me. Please, Need Help.. Thanks in advance. Bless..!!
Click to expand...
Click to collapse
Problem Fixes, thanks to
Ganga -->>> [email protected]> Thanks my Brother, very honest and Knowledgeable with the Xioami Mi 11. I was VERY happy that I did have to remove the back Glass and find the 2 copper prongs like other people were forced to do. Bless.
Pho3nX said:
If you can't access on your recovery... It's bricked. Are you sure to have flash the good ROM ? When you have this problem, it's due to a bad ROM flashed or corrupted Data / Download (Bad CRC/MD5) flashed under MiFlash on Fastboot Mode.
1/ Try combinaison : POWER + "-" or POWER + "+" with 5 seconds press
2/ Plug your Phone on your computer, launch Xiaomi Unlock (show device ? Locked/Unlocked Status ?)
3/ Plug your Phone on your computer, MiFlash (show device ? Locked/Unlocked Status ?)
4/ Plug your Phone on your computer, try "XiaoMiTool V2" for trying Unbrick
Click to expand...
Click to collapse
There's no such thing as "bricked" in 2021... even if you have to flash it via EDL, still not bricked.
LowaEastSide said:
hey. Im hoping i can get some help. i just purchased the Chinese Version of the Mi 11, i waited a week and just unlocked the bootloader so decided to flash the Global Rom. However, things went wrong and now im stuck with a black screen. I can NOT get into recovery, but i do hear the devices connecting when i plug it in. I was on the Chinese Version 12.5.9.0. I tried flashing the Global Version 12.0.22.0, the when it i got stuck on the black screen. I tried to do research on it but can not figure it out for the life of me. Please, Need Help.. Thanks in advance. Bless..!!
Click to expand...
Click to collapse
I had same situation on Redmi K20 Pro. You'll need to flash it using Mi Flash with a dev account via EDL.
And after flashing global rom, never neeever NEVER lock it back when not having chinese rom on a chinese phone.
You are in edl mode, you can flash this rom :
Official Engineering Firmware for Mi 11 : https://drive.google.com/file/d/1quyYpwV8IkZxnICZ2PEBXduuarxemlBI/view?usp=sharingi reupload this for you, tell me when you have downloaded it. Flash it with mi flash, let the phone boot, reboot in fastboot and flash the rom you want.
Pikaone41 said:
You are in edl mode, you can flash this rom :
Official Engineering Firmware for Mi 11 : https://drive.google.com/file/d/1quyYpwV8IkZxnICZ2PEBXduuarxemlBI/view?usp=sharingi reupload this for you, tell me when you have downloaded it. Flash it with mi flash, let the phone boot, reboot in fastboot and flash the rom you want.
Click to expand...
Click to collapse
Thanks you for the EDL firmware. I will download it and just in case I'll ever need it in the future. Plus I'll keep you in mind if ever I need help in the future. Honestly, I never had such a hard time reflashing a device stuck in bootloop. I've flashed so many devices in my life time but never came across such a difficult device to repair. More thank likely I'll be sticking to OnePlus. Much easier.
Hello all,
I just got the V12.5.5.0 update on my Redmi Note 10 5G (Global).
After I rebooted the system tapping the complete notification it is stuck on the MIUI Recovery screen.
My device is not rooted. It just has received OTA updates.
I tried to reboot the system a few times, but it didn't work.
Also, I tried the safe mode, but it didn't work either.
After Reboot or safe mode, it returns to the MIUI Recovery screen.
I haven't tried the Wipe Data option because I want to back up my files first if possible.
Is there any way to back up my files or be able to fix it?
Please help.
Thanks in advance.
the only solution is enter into fastboot mode and flash stock fastboot firmware via miflash or similar tool
wetito said:
the only solution is enter into fastboot mode and flash stock fastboot firmware via miflash or similar tool
Click to expand...
Click to collapse
I tried that, but I am getting an error saying not allowed in locked state. It looks like the bootloader is locked, so I tried to use the Mi Unlock tool but I am getting error 1004. Also I tried wipe data, but it didn't work either. Right now, I don't care loss my data, I just want to have my phone back, any help is appreciated. Thanks
I have the exact same problem, after the update, lock on recovery mode, then when I tried to flash stock fastboot firmware it says that it is locked. And I also can't access Mi Unlock Tool for some reason, so if anybody has a solution to unlock bootloader I would really appreciate it.
Thanks
I got this same issue. Is there any way we can report this to mi? I don't mind if I lose my data rn, I just want this to start working normally again. someone please help if you know how to fix this
jyeros said:
Hello all,
I just got the V12.5.5.0 update on my Redmi Note 10 5G (Global).
After I rebooted the system tapping the complete notification it is stuck on the MIUI Recovery screen.
My device is not rooted. It just has received OTA updates.
I tried to reboot the system a few times, but it didn't work.
Also, I tried the safe mode, but it didn't work either.
After Reboot or safe mode, it returns to the MIUI Recovery screen.
I haven't tried the Wipe Data option because I want to back up my files first if possible.
Is there any way to back up my files or be able to fix it?
Please help.
Thanks in advance.
Click to expand...
Click to collapse
Same here, albeit I have Chinese version on Global ROM
wetito said:
the only solution is enter into fastboot mode and flash stock fastboot firmware via miflash or similar tool
Click to expand...
Click to collapse
Have you downgraded? Tried to, but accidentally locked bootloader. And it shows that version I have installed isn't compatible.
Use MTK Bypass for reparing https://megafon929.github.io/mtk
Timenator said:
Have you downgraded? Tried to, but accidentally locked bootloader. And it shows that version I have installed isn't compatible.
Click to expand...
Click to collapse
i'm an absolute beginner at this stuff, so could you tell me how to downgrade it?
i suppose try booting in safe mode dint work. the only solution is flashing full firmware, cause the ota packet is bugged.
try this tool
Home - Tool All In One
TOOL ALL IN ONE This tool support 67 different devices of some different OEMs. DOWNLOAD CHANGELOG XDA THREAD OTHERS PROJECTS
toolaio.tk
Timenator said:
Have you downgraded? Tried to, but accidentally locked bootloader. And it shows that version I have installed isn't compatible.
Click to expand...
Click to collapse
I received the device yesterday, the update notification arrived and I installed it, I didn't imagine it could be a problem, I tried to reinstall the rom but the bootloader is also blocked, I don't know what else to do, I'm desperate.
LucciM-Anon said:
i'm an absolute beginner at this stuff, so could you tell me how to downgrade it?
Click to expand...
Click to collapse
Rafaelmaga said:
I received the device yesterday, the update notification arrived and I installed it, I didn't imagine it could be a problem, I tried to reinstall the rom but the bootloader is also blocked, I don't know what else to do, I'm desperate.
Click to expand...
Click to collapse
Found a solution on web. If your phone is on Mediatek(I suppose all Note 10 5g are Mediatek? or no?) So, if it is, just look for an unlocker. You will also need MiFlash and I recommend to install Global MIUI 12.5.4. https://xiaomifirmwareupdater.com/miui/camellian/stable/V12.5.4.0.RKSMIXM/ - MIUI
Step by step guide:
How to Fix Your Hard Bricked Xiaomi Phone With Locked Bootloader
If you are familiar with custom ROM or flashing your phone, then there's a possibility that you have tried flashing your Xiaomi/Redmi/POCO Phone. Earlier
gadgetstouse.com
Timenator said:
Found a solution on web. If your phone is on Mediatek(I suppose all Note 10 5g are Mediatek? or no?) So, if it is, just look for an unlocker. You will also need MiFlash and I recommend to install Global MIUI 12.5.4. https://xiaomifirmwareupdater.com/miui/camellian/stable/V12.5.4.0.RKSMIXM/ - MIUI
Step by step guide:
How to Fix Your Hard Bricked Xiaomi Phone With Locked Bootloader
If you are familiar with custom ROM or flashing your phone, then there's a possibility that you have tried flashing your Xiaomi/Redmi/POCO Phone. Earlier
gadgetstouse.com
Click to expand...
Click to collapse
unfortunately this tutorial doesn't work here, I followed everything but it still didn't unlock the bootloader
Hi guys, I just woke up and my phone was in MIUI Recovery mode, just like yours.. Probably made the update automatically.
It seems this is a recent problem for many of us. I'm nowhere near an expect but I will continue looking for the solution (if possible, without whiping out the data or at least to be able to back-it up).
Will really appreciate if somebody posts if they find a solution.
Thanks!
The only solution is to wipe the phone. I got my lesson I will buy a samsung now
Hello all,
I got the V12.5.5.0 update to on my Redmi Note 10 5G (Global).
After I rebooted the system tapping the complete notification it is stuck on the MIUI Recovery 5.0 screen.
My device is not rooted. It just has received OTA updates.
I tried to reboot the system a few times, but it didn't work.
Also, I tried the safe mode, but it didn't work either.
After Reboot or safe mode, it returns to the MIUI Recovery screen.
I have tried the Wipe Data option and it worked and got me back to MIUI V12.5.4.0. But unfornnatly i lost all my files (about 90 Gb of data).
And this is the last i install any MIUI update until i see that a lot of user's have install it review it
My Poco M3 Pro 5G Global wasn't affected.
I manually download the OTA package and installed successfully.
This phone has a/b slot.
I'm wondering those facing this issue, have you tried switching from a to b slot or vice versa?
fastboot --set-active=a
fastboot --set-active=b
guyz92 said:
My Poco M3 Pro 5G Global wasn't affected.
I manually download the OTA package and installed successfully.
This phone has a/b slot.
I'm wondering those facing this issue, have you tried switching from a to b slot or vice versa?
fastboot --set-active=a
fastboot --set-active=b
Click to expand...
Click to collapse
i think the ota released by xiaomi is bugged. you're operation is correct, but a correct ota might do this automatically. i have noticed that many users with unlocked bootloader, after the update have phone that dont boot. i think they cant enter on fastboot mode. the only solution is flash using mediatek SP FLASH TOOL. or MI FLASH PRO. or ALL IN ONE TOOL
Was someone able to access the "Connect with MIAssistant" part using pcsuite?
I couldn't, but I think it might be because the USB cable I'm using is not the original one from Xiaomi or one compatible.
work only if you have installed also pcsuite on your device. if u have a full stock loked device only solutions are Mediatek tool or miflash pro! or all in one tool. as i said a million time already