Hi,
i unlock the bootloader with the Motorola key and boot twrp than I install supersu.
during the install process the message cach not found appear, after reboot
the device does not start, the display shows the "M screen powerd by android"
Can I rescue the phone?
I can boot in into the bootloader mode I try to flash the twrp but the message unknown partiton twrp.img is showing
the partition are damage
I do the option format data the partition are rescued, but android does not start.
I think I need the factory firmware but on the Motorola website I can t found them.
Use magisk instead, it's a systemless root method.
There's tutorials on how to flash stock firmware on the rom and tutorial sections.
Read the twrp tutorial to install twrp, since it doesn't install through the traditional fastboot method, you need to flash twrp.zip in twrp to retain it as a recovery.
I don't have much time to walk you through it at this moment, but there are tutorials all around the Moto x4 sub forum, I'd recommend looking for and reading them.
Thanks for support, I was able to restore the partitions, the bootloader was broken, I flashed the android one veraion and it works I will do the next root trial with magisk
Related
To start: 5.1.1 (LMY48M), rooted, with TWRP for recovery
For every 5.x update so far, this has been my procedure using fastboot:
Flash boot.img
Flash radio.img
Flash system.img
After successfully updated, I'd use WugFresh's Nexus toolkit to root and flash TWRP.
I'm a fan of not needing to flash userdata.img, as I don't think that should be necessary given that the OTA wouldn't wipe installed apps and such.
I've read other threads about using fastboot to upgrade and am concerned about the boot warnings, which seem to require a custom kernel to circumvent. My question is: will the above approach still work? Do I need to flash any other files? If I need to flash a custom kernel, where do I get it, how do I flash it (is it just a custom boot.img?), and at which point in the flash sequence should I apply it?
Secondly, has anyone tried gaining root through the Nexus toolkit once upgraded to 6.0?
I'm looking for recommendations so I don't spend hours trying to unbrick my device. Thanks!
You'll also want to flash the 6.0 bootloader and why are you using the toolkit to flash twrp when you can flash it in fastboot along with the rest of the files?
Ah OK, I'll flash the bootloader image as well. Anything else to be concerned with? The toolkit has a feature to root + flash twrp as a feature, so I just use that.
Do the bootloader first, then reboot the bootloader before you flash anything else. There are instructions floating around here some where or you can google nexus 6 flash factory images. You don't have to flash user data as this will format all you data/ apps.
Just download the latest SuperSu zip (2.50) and put it on your SDcard. If you flash as you suggested and then boot directly into recovery, you will still have TWRP. If you don't flash the stock recovery.img to replace TWRP, it will replace on first boot anyway, unless you root imeediately, but you are probably booting to use the toolkit, which replaces recovery only to have to use the toolkit to flash recovery anwyay.
So do your flashes, boot straight into recovery, flash the supersu zip on your sdcard. Done.
Newbie to the 'Dark Side of the Android World' and just curious.
well, after rooting your phone you only need to flash custom recovery once then you can access it as many times as you want
Your question is a little bit weird. Can you link me to a place of reference? Or at least explain what you are actually wanting to do?
Flashing TWRP is a one-time action, once flashed it remain on your Xperia SP. However, FlashTool doesn't offer flashing TWRP to other partitions via fastboot other than the "boot" partition. So far, the only way to correctly flash TWRP is via a recovery.
If you indeed flashed TWRP image via FlashTool, then you are actually putting TWRP into your boot partition, and this makes your device to only boot into TWRP infinitely until you flash a ROM (which will of course again override the boot partition).
The reason why I asked is because this method of accessing recovery is posted in my custom ROM guide, so I want to know if you get this kind of idea from my guide.
Thanks
I unlocked boot loader and tried to install twrp from system,it says its installed but i cant enter it
How to flash twrp the best way
And can i remove twrp if i need to restore factory state and how to delete it?
Thank you
You could always try XperiaZdual-recovery, as long you don't flash another kernel. Its actually a tool that can help you flash the recovery (if not rooted yet, you must be on 5.0.2) using only a one-click solution. It does not give you root access and you should allow usb debugging in order to be able to flash. It installs TWRP and Philz recovery, during boot you can select either one of them using volume down for the first and volume up for the latter. Have fun.
How to remove twrp from xperia xz(f8332)
Hi there, I am currently running B383 on my P9, and really want to root it. However when I do, will I still be able to get future updates to the software? Do I need to unroot and lock bootloader first?
Also when the bootloader is unlocked, a message is displayed at boot about your phone being unsecured and non-trustworthy, is it possible to remove this message? (I used to have a moto g with an unlocked bootloader, and I flashed some file to remove the warning).
Thanks
I don't think there is a way to remove that message every time the phone is turned on. Mine does that too as I've unlocked the bootloader.
Did you unlock the bootloader yet? Because when you need to unlock it, the phone will basically be factory reset when bootloader is switched from locked to unlock (vice-versa).
And for OTA updates the best way is to do it manually, downloading the MV-PV file via Huawei Firmware finder (Full PV file which contains two files update.zip and hweu..zip, update.zip (system firmware) is flashed first then hweu.zip (The system apps).
You will need a custom recovery. The one you will need to use is TWRP (This one specifically - twrp-3.1.1-0-eva.img) to flash OTA's via custom recovery (To repeat you flash update.zip first then hweu.zip) You can ignore the errors if it prints any while flashing the OTA files as I did the same and it worked fine no problem.
When you want to root your phone, make sure to flash 'SuperSU-v.2.82-EMUI5-SELEnforcing.zip' via TWRP recovery to root your phone.
For the other questions, you do not need to unroot the phone to install the OTA updates. The phone will just unroot itself when the OTA update is flashed onto phone. You simply just need to re-root it again by re flashing the SuperSU zip as mentioned above.
When you need to boot the custom TWRP recovery you need to turn the phone off and hold power + volume up until Huawei Logo / text is displayed you must release both keys immediately after 0.5-1 second which is a short time frame to get the phone to boot to custom recovery or else it will boot the Huawei eRecovery instead.
SuperSU here: https://forum.xda-developers.com/p9/development/root-supersu-2-81-emui-5-t3612258
TWRP here: https://forum.xda-developers.com/p9/development/twrp-t3565703
Best to follow the instructions from those links. The information above is to guide you through the processes.
..
benjamen50 said:
I don't think there is a way to remove that message every time the phone is turned on. Mine does that too as I've unlocked the bootloader.
Did you unlock the bootloader yet? Because when you need to unlock it, the phone will basically be factory reset when bootloader is switched from locked to unlock (vice-versa).
And for OTA updates the best way is to do it manually, downloading the MV-PV file via Huawei Firmware finder (Full PV file which contains two files update.zip and hweu..zip, update.zip (system firmware) is flashed first then hweu.zip (The system apps).
You will need a custom recovery. The one you will need to use is TWRP (This one specifically - twrp-3.1.1-0-eva.img) to flash OTA's via custom recovery (To repeat you flash update.zip first then hweu.zip) You can ignore the errors if it prints any while flashing the OTA files as I did the same and it worked fine no problem.
When you want to root your phone, make sure to flash 'SuperSU-v.2.82-EMUI5-SELEnforcing.zip' via TWRP recovery to root your phone.
For the other questions, you do not need to unroot the phone to install the OTA updates. The phone will just unroot itself when the OTA update is flashed onto phone. You simply just need to re-root it again by re flashing the SuperSU zip as mentioned above.
When you need to boot the custom TWRP recovery you need to turn the phone off and hold power + volume up until Huawei Logo / text is displayed you must release both keys immediately after 0.5-1 second which is a short time frame to get the phone to boot to custom recovery or else it will boot the Huawei eRecovery instead.
SuperSU here: https://forum.xda-developers.com/p9/development/root-supersu-2-81-emui-5-t3612258
TWRP here: https://forum.xda-developers.com/p9/development/twrp-t3565703
Best to follow the instructions from those links. The information above is to guide you through the processes.
Click to expand...
Click to collapse
Thanks for the quality answer, I have no doubts anymore!
Hi I'm a new Android user and don't know much about it :'( I recently got my OnePlus 3T and I wanted to root it
so I followed a tutorial video from YouTube successfully unlocked bootloader and flashed twrp recovery then I tried to install SuperSU... well it installed but the device got soft bricked when I rebooted after finishing the installation and wiping cache/dalvik
then I format/factory reset everything using twrp recovery and it's working now but the device isn't rooted :'( tried to install SuperSU again and it got bricked again
Also I'm getting these messages on the startup screen-
1st one: Your device has been unlocked and can't be trusted. If you don't want to see this screen please lock your device by "fastboot oem lock" and erase user data.
2nd one: The dm-verity is not started in enforcing mode and may not work properly.
(My os version is 4.1.7)
device OP 3t A3010
plz help me :'(
The 1st and the 2nd msg that gets displayed is shown because the bootloader is unlocked..
Bootloops are common while flashing su...when I flashed super su for the first time, I got 3 or 4 random reboots and took almost 7 to 10 mins for the phone to boot up..
I would suggest using Magisk as a rooting method instead of SuperSU. If you use SuperSU then some apps can detect root and object to you being rooted and Google's SafetyNet gets triggered. Magisk solves this by trying to hide root from apps and Google so that you can use your device as if it wasnt rooted at all (but in fact is rooted). Go the the Magisk forum and download Magisk 13.3 zip from there.
I am assuming you are using OxygenOS (Oneplus's software) and not a custom ROM. Download the Open Beta or Stable build from here/
These steps will erase all the data on your phone permanently (including internal storage) so please backup anything in there.
To fix the DM verity error youll have to follow the steps outlined here
Once you have fixed that, flash oneplus recovery via fastboot which you can download here
To flash it go to fastboot mode, and cd into the folder where you downloaded it. Run the command 'fastboot flash recovery <RECOVERY_NAME>'.
Then run the command 'fastboot oem lock' to lock the bootloader. After you confirm the prompt on screen, the phone will boot into the recovery and youll see a progress bar. Once the progress completes and the screen turns off, be ready to immediately go back to fastboot mode by pressing volume up and power.
When you enter fastboot mode again, run the command 'fastboot oem unlock' and follow the same steps as before.
Once you are in fastboot mode, the phone is now in a clean state with no OS.
Follow the steps outlined on the oneplus website to flash a clean OxygenOS build (stable or open beta as per your taste)
Once the flashing is complete you have to let the phone boot up completely once. When you get to the setup screen, go through it and reach the launcher.
Now we flash TWRP recovery. Reboot to fastboot again. Flash TWRP recovery (I personally use blu_spark's twrp but you can use one of your choice). When it is done, boot into the recovery. Youll now be able to copy magisk zip into the internal sd. Do that, and flash it. Reboot.
Youll now be rooted. If you have any problems holla at me.