Database Develop

Install Emui 8 Android 8.0 B533/B530/B528/B520/B511/B510 on Honor Note 8

Hi,
i thought I would make a new tread for that,because some have problems with it and it is clearer.
You need:
Firmware B533/B530/B528/B520/B511 or B510
HuRUpdater 0.3 for Edison AL10
IMG Files
Twrp for Oreo
This Twrp works only with Oreo and not with Nougat!
http://pro-teammt.ru/firmware-database/?firmware_model=edi&firmware_page=0
HuRUpdater 0.3 only for Edison AL10 Link here Thanks goes to zxzo0o for this Tool
Img Files Recovery,Kernel,Ramdisk https://www.androidfilehost.com/?fid=674106145207497141
Download all Files:Three Firmware Files,Img Files.zip and HuRUpdater0.3
Extract the IMG Files with Winzip,Rar...
Copy the three Firmware files,HuRUpdater0.3 and the Stockrecovery in a Folder on MicroSD on your Honor Note 8.Rename the RECOVERY_RAMDIS.img to recovery.img before copy in this Folder!
Copy KERNEL.img,RAMDISK.img and RECOVERY_RAMDIS.img in your ADB Folder for later.
Requirements:
You have to be on B359 Unlocked Bootloader and have Twrp installed!(Use Twrp for Nougat)
Instructions:
Boot into Twrp and wipe all:Format Data with "Yes"(Do you have a mistake while booting into the Erecovery and Format Data,you have the Option Format Data Partition,if an error occurs in Twrp)
Boot in Twrp and Format Data with "Yes" again.
Reboot after Format Data in Twrp again.
Format in advanced Wipe:System,Data,Cache,Dalvik Cache and Cache and reboot into Twrp.
Install the HuRUpdater0.3 in Trwp and follow the instructions.
After installing reboot into Bootloader,the Bootloader is locked.
Unlock the Bootloader with your Unlockcode.
In my case:My Phone boot not into System and it will display an error white background picture with red text and Notyfication Led flashes red.If not and your Phone boot into System skip this step.
Reboot into Bootloader and flash KERNEL.img,RAMDISK.img and RECOVERY_RAMDIS.img via ADB.
fastboot flash ramdisk RAMDISK.img
fastboot flash kernel KERNEL.img
fastboot flash recovery_ramdisk RECOVERY_RAMDIS.img
fastboot reboot
The Phone boot not into System,make a Factory Reset with Volume up and Power Button.(shows Chinese Recovery)
After Reset Boot,if your sim card does not work make a Factory Reset(Low Level Reset)Into Settings Factory Reset with Internal Memory.
The Phone Boot and all works,i test it with B510,B511 and B520
I am on B533 with Security Patch August 2018
If you will go back to Android 7 B359,boot into Erecovery and restore via wifi to B359.
I hope you understand my Bad English!

I think there will be Twrp soon, for the Mate 8 with Emui 8 there is already one on the Chinese Page.
https://cn.club.vmall.com/thread-16048510-1-2.html
That should work on the HN8.
The Twrp HN8 for Android 7 is also from the Mate 8
Unfortunately, I can not log in.
Maybe someone has a Vmall account and can download it?
Then you can try it if it works

TWRP
letschky said:
I think there will be Twrp soon, for the Mate 8 with Emui 8 there is already one on the Chinese Page.
https://cn.club.vmall.com/thread-16048510-1-2.html
That should work on the HN8.
The Twrp HN8 for Android 7 is also from the Mate 8
Unfortunately, I can not log in.
Maybe someone has a Vmall account and can download it?
Then you can try it if it works
Click to expand...
Click to collapse
Here is the File that you requested from the link. I have not tested it myself. Good luck with your testing!
Download huawei-nxt-al10-em8_0-twrp3.2.1-8.5.21.img

letschky said:
Hi,
i thought I would make a new tread for that,because some have problems with it and it is clearer.
You need:
Firmware B520/B511 or B510
HuRUpdater 0.3
IMG Files
Downloads:
http://pro-teammt.ru/firmware-database/?firmware_model=edi&firmware_page=0
HuRUpdater 0.3 Link here Thanks goes to zxzo0o for this Tool
Img Files Recovery,Kernel,Ramdisk https://www.androidfilehost.com/?fid=674106145207497141
Download all Files:Three Firmware Files,Img Files.zip and HuRUpdater0.3
Extract the IMG Files with Winzip,Rar...
Copy the three Firmware files,HuRUpdater0.3 and the Stockrecovery in a Folder on MicroSD on your Honor Note 8.Rename the RECOVERY_RAMDIS.img to recovery.img before copy in this Folder!
Copy KERNEL.img,RAMDISK.img and RECOVERY_RAMDIS.img in your ADB Folder for later.
Requirements:
You have to be on B359 Unlocked Bootloader and have Twrp installed!(For Android 8 There is no Twrp available yet)
Instructions:
Boot into Twrp and wipe all:Format Data with "Yes"(Do you have a mistake while booting into the Erecovery and Format Data,you have the Option Format Data Partition,if an error occurs in Twrp)
Boot in Twrp and Format Data with "Yes" again.
Reboot after Format Data in Twrp again.
Format in advanced Wipe:System,Data,Cache,Dalvik Cache and Cache and reboot into Twrp.
Install the HuRUpdater0.3 in Trwp and follow the instructions.
After installing reboot into Bootloader,the Bootloader is locked.
Unlock the Bootloader with your Unlockcode.
In my case:My Phone boot not into System and it will display an error white background picture with red text and Notyfication Led flashes red.If not and your Phone boot into System skip this step.
Reboot into Bootloader and flash KERNEL.img,RAMDISK.img and RECOVERY_RAMDIS.img via ADB.
fastboot flash ramdisk RAMDISK.img
fastboot flash kernel KERNEL.img
fastboot flash recovery_ramdisk RECOVERY_RAMDIS.img
fastboot reboot
The Phone boot not into System,make a Factory Reset with Volume up and Power Button.(shows Chinese Recovery)
After Reset Boot,if your sim card does not work make a Factory Reset(Low Level Reset)Into Settings Factory Reset with Internal Memory.
The Phone Boot and all works,i test it with B510,B511 and B520
I am on B520 with Security Patch June 2018
If you will go back to Android 7 B359,boot into Erecovery and restore via wifi to B359.
I hope you understand my Bad English!
Click to expand...
Click to collapse
Please wen will OTA release. Thanks
Sent from my EDI-AL10 using Tapatalk

TITAN-23 said:
Here is the File that you requested from the link. I have not tested it myself. Good luck with your testing!
Download huawei-nxt-al10-em8_0-twrp3.2.1-8.5.21.img
Click to expand...
Click to collapse
Uuhh,thanks Man!!!

ok,i install Twrp first failed.(remote: Command not allowed)The Problem isif the phonefinder is activated via the Huaweikonto you can not flash twrp.
I make a Factory Reset in Settings with Internal Memory and flash Twrp again and works,i can boot into Twrp.
Problem Data Partition not mounted.
Ok,i format Data with "yes" reboot again into Twrp and Data is mounted.
I flash 2 Files from the 3 Firmwarefiles in Twrp.update_data_full_public.zip and update_full_EDI-AL10_all_cn.zip and the Phone boot into System.
Short set up and boot again in Twrp and Data Partition is mounted.
Now all I have to do is try to root,i hope it works.
Twrp is only Chinese and English Language!

First i make a Backup,you can backup all Partitions,System,Data,Boot,Cust,Vendor,Version,Product,cool.
Next i test root if the Backup Finish

letschky said:
ok,i install Twrp first failed.(remote: Command not allowed)The Problem isif the phonefinder is activated via the Huaweikonto you can not flash twrp.
I make a Factory Reset in Settings with Internal Memory and flash Twrp again and works,i can boot into Twrp.
Problem Data Partition not mounted.
Ok,i format Data with "yes" reboot again into Twrp and Data is mounted.
I flash 2 Files from the 3 Firmwarefiles in Twrp.update_data_full_public.zip and update_full_EDI-AL10_all_cn.zip and the Phone boot into System.
Short set up and boot again in Twrp and Data Partition is mounted.
Now all I have to do is try to root,i hope it works.
Twrp is only Chinese and English Language!
Click to expand...
Click to collapse
this is what i get:
target reported max download size of 471859200 bytes
sending 'recovery' (12460 KB)...
OKAY [ 0.275s]
writing 'recovery'...
FAILED (remote: partition length get error)
finished. total time: 0.298s

Voyebanm said:
this is what i get:
target reported max download size of 471859200 bytes
sending 'recovery' (12460 KB)...
OKAY [ 0.275s]
writing 'recovery'...
FAILED (remote: partition length get error)
finished. total time: 0.298s
Click to expand...
Click to collapse
https://forum.xda-developers.com/showpost.php?p=76861896&postcount=6

I successfully rooted it with Magisk,i delete unessersay Apps,smaler icon Mod works,disable online China services in Music and Viedeoplayer,yeah

We wait your full manual! As always!
2 pages long

letschky said:
https://forum.xda-developers.com/showpost.php?p=76861896&postcount=6
Click to expand...
Click to collapse
I did follow that.
phonefinder is not activated .
I tried again , still the same error

Voyebanm said:
I did follow that.
phonefinder is not activated .
I tried again , still the same error
Click to expand...
Click to collapse
I had the same issue,i go into Settings and make Factory Reset with internal Memory.(Low Level Reset)
After reboot short setup and boot into Bootloader.The Twrp img is in the ADB Folder?Remame the Twrp to a shorter Name (TWRP_HN8.img)and flash it.
fastboot flash recovery_ramdisk TWRP_HN8.img

ivanox1972 said:
We wait your full manual! As always!
2 pages long
Click to expand...
Click to collapse
I will update later Today

I have one issue,setting does not work,i think i delete wrong file,aahh

@letschky
Now, I am on B511.
How to update from B511 to B520? please advise.
Thank you

letschky said:
ok,i install Twrp first failed.(remote: Command not allowed)The Problem isif the phonefinder is activated via the Huaweikonto you can not flash twrp.
I make a Factory Reset in Settings with Internal Memory and flash Twrp again and works,i can boot into Twrp.
Problem Data Partition not mounted.
Ok,i format Data with "yes" reboot again into Twrp and Data is mounted.
I flash 2 Files from the 3 Firmwarefiles in Twrp.update_data_full_public.zip and update_full_EDI-AL10_all_cn.zip and the Phone boot into System.
Short set up and boot again in Twrp and Data Partition is mounted.
Now all I have to do is try to root,i hope it works.
Twrp is only Chinese and English Language!
Click to expand...
Click to collapse
Hi,
Now I am able to install TWRP and boot in it and mount data no problem
after I rep-flashed the 2 files, Just a boot loop now.
I can now re-install B520 and boot no problem with Network working right away, but I lose TWRP after the installation and restarted the process with the same problem.

Now, I am on B511, I try to flash new twrp (huawei-nxt-al10-em8_0-twrp3.2.1-8.5.21.img)
But I still found error "remote: partition length get error".

dekwat said:
Now, I am on B511, I try to flash new twrp (huawei-nxt-al10-em8_0-twrp3.2.1-8.5.21.img)
But I still found error "remote: partition length get error".
Click to expand...
Click to collapse
this the new command:
fastboot flash recovery_ramdisk huawei-nxt-al10-em8_0-twrp3.2.1-8.5.21.img

Voyebanm said:
this the new command:
fastboot flash recovery_ramdisk huawei-nxt-al10-em8_0-twrp3.2.1-8.5.21.img
Click to expand...
Click to collapse
Yes, I try this command but I still found same error.
P.S. I'm not sure, this twrp can use for B511 or not.

I bricked my OnePlus 7 Pro (was stuck and fastboot) and how I fixed it

Hi, I'm writing this to guide those who faced - and will face similar situation in the future - the problem of being stuck on the fastboot screen, where the recovery or booting in EDL is not available.
So, after failing to get root after upgrading to android 10 I was fiddling with TWRP to try to get it to recognize my storage so I can reflash it and flash Magisk, but I couldn't get it to mount the storage, so my stupid brain decided to go to the wipe page and wiped everything in the hope it might magically work!! well.. it didn't!! and I got stuck in the fastboot screen and I thought that I bricked my phone for good.
after hours of searching online and trying everything nothing helped... but finally I managed to fix it.
and btw when I tried to flash TWRP by (fasboot boot twrp.img) I got the following message:
"remote: Failed to load/authenticate boot image: Load Error"
So here is what I did to get my phone working again:
Download and install Tool All in One
Download Fastboot ROM for your phone from here
In the Tool All in One app click on the Flash Factory Images button.
Select the ROM and let it do its work,
hopefully this will work and your device will reboot into a fresh android.

Also it's good to know that the official TWRP of twrp.me does not support Android Q at the moment, that's why you couldn't decrypt and mount the storage. TWRP in Oneplus 7 Pro thread here on XDA does support Q, you just have to remember to boot into the inactive/upgraded slot before booting back to TWRP to flash Magisk as it only installs to the active slot and not the upgraded slot.
Skickat från min GM1913 via Tapatalk

vegatr0n said:
Hi, I'm writing this to guide those who faced - and will face similar situation in the future - the problem of being stuck on the fastboot screen, where the recovery or booting in EDL is not available.
So, after failing to get root after upgrading to android 10 I was fiddling with TWRP to try to get it to recognize my storage so I can reflash it and flash Magisk, but I couldn't get it to mount the storage, so my stupid brain decided to go to the wipe page and wiped everything in the hope it might magically work!! well.. it didn't!! and I got stuck in the fastboot screen and I thought that I bricked my phone for good.
after hours of searching online and trying everything nothing helped... but finally I managed to fix it.
and btw when I tried to flash TWRP by (fasboot boot twrp.img) I got the following message:
"remote: Failed to load/authenticate boot image: Load Error"
So here is what I did to get my phone working again:
Download and install Tool All in One
Download Fastboot ROM for your phone from here
In the Tool All in One app click on the Flash Factory Images button.
Select the ROM and let it do its work,
hopefully this will work and your device will reboot into a fresh android.
Click to expand...
Click to collapse
Or just use the MSM tool. Job done

All with varying levels of interpretation, steps, descriptions, and the solution. Not all are useful.

I had the same issue and this worked perfectly to get my device up and running again. Thanks again!!

Hi all!
Here is plan B!
First of all - BEFORE you do some upgrade - make OPSwitch backup and copy to PC !!!!!
If you stuck - it's mean that something is badly damaged and wrong. Some of the files reside in the areas where upgrade tools (including Fastboot!) can't change and repair them.
We don't have time, knowledge to sort out WHAT was damaged.
We make all straight from beginning:
1. MSM tools - make your phone like from the Factory with "clean" install (ver 9 for now)
2. "FlashAll" то ver 10E
3. If you need - install "global"
4. If you need - install TWRP and Magisk
5. Restore your backup from PC
At the end you will have "clean" phone with all programs working
EASY!!!

Same as OP, I wanted to flash twrp.img.
I had my OP7Pro stuck in 'fastboot mode', I thought. It wouldn't respond to any commands from console (device not found) and I couldn't turn it off with the power button any more.
For noobs, just like me, I learned that I just had to press the powerbutton + volume up button. My phone rebooted after this.
Now making a backup before rooting and such, phew.

vegatr0n
I was stuck in Fastboot after switching slots. Excelent stuf! 2,3 clicks , done! Thank you!

vegatr0n said:
Hi, I'm writing this to guide those who faced - and will face similar situation in the future - the problem of being stuck on the fastboot screen, where the recovery or booting in EDL is not available.
So, after failing to get root after upgrading to android 10 I was fiddling with TWRP to try to get it to recognize my storage so I can reflash it and flash Magisk, but I couldn't get it to mount the storage, so my stupid brain decided to go to the wipe page and wiped everything in the hope it might magically work!! well.. it didn't!! and I got stuck in the fastboot screen and I thought that I bricked my phone for good.
after hours of searching online and trying everything nothing helped... but finally I managed to fix it.
and btw when I tried to flash TWRP by (fasboot boot twrp.img) I got the following message:
"remote: Failed to load/authenticate boot image: Load Error"
So here is what I did to get my phone working again:
Download and install Tool All in One
Download Fastboot ROM for your phone from here
In the Tool All in One app click on the Flash Factory Images button.
Select the ROM and let it do its work,
hopefully this will work and your device will reboot into a fresh android.
Click to expand...
Click to collapse
Many people have found this problem. Thank you, I am working again.

i am not even able to flash the twrp in android 10 always getting stuck at fastbootlogo after flashing the recovery cmd

nitinvaid said:
i am not even able to flash the twrp in android 10 always getting stuck at fastbootlogo after flashing the recovery cmd
Click to expand...
Click to collapse
Then you have to use the MSM unbrick tool:
https://forum.xda-developers.com/oneplus-7-pro/how-to/op7pro-collection-unbrick-tools-t3956595/amp/

vegatr0n said:
Then you have to use the MSM unbrick tool:
https://forum.xda-developers.com/oneplus-7-pro/how-to/op7pro-collection-unbrick-tools-t3956595/amp/
Click to expand...
Click to collapse
Nope...
I was able to reboot holding both vol+ and - and power

I bricked my tmobile oneplus 7 pro and dont know which file is safe to try can anyone please point me in the right direction?

I already tried the steps using the tool and downloading the FASTBOOK os file and I get this error
"CreateProcess failed: %1 is not a valid Win32 application. (193)
fastboot: error: Cannot generate image for userdata"
Tried booting the device but boots to OOS recovery always.
---------- Post added at 11:54 PM ---------- Previous post was at 11:21 PM ----------
vegatr0n said:
Hi, I'm writing this to guide those who faced - and will face similar situation in the future - the problem of being stuck on the fastboot screen, where the recovery or booting in EDL is not available.
So, after failing to get root after upgrading to android 10 I was fiddling with TWRP to try to get it to recognize my storage so I can reflash it and flash Magisk, but I couldn't get it to mount the storage, so my stupid brain decided to go to the wipe page and wiped everything in the hope it might magically work!! well.. it didn't!! and I got stuck in the fastboot screen and I thought that I bricked my phone for good.
after hours of searching online and trying everything nothing helped... but finally I managed to fix it.
and btw when I tried to flash TWRP by (fasboot boot twrp.img) I got the following message:
"remote: Failed to load/authenticate boot image: Load Error"
So here is what I did to get my phone working again:
Download and install Tool All in One
Download Fastboot ROM for your phone from here
In the Tool All in One app click on the Flash Factory Images button.
Select the ROM and let it do its work,
hopefully this will work and your device will reboot into a fresh android.
Click to expand...
Click to collapse
I am getting the error
"Erasing 'userdata' OKAY [ 0.243s]
CreateProcess failed: %1 is not a valid Win32 application. (193)
fastboot: error: Cannot generate image for userdata"
I dont know how to proceed with this :crying:

moonbosques said:
I already tried the steps using the tool and downloading the FASTBOOK os file and I get this error
"CreateProcess failed: %1 is not a valid Win32 application. (193)
fastboot: error: Cannot generate image for userdata"
Tried booting the device but boots to OOS recovery always.
---------- Post added at 11:54 PM ---------- Previous post was at 11:21 PM ----------
I am getting the error
"Erasing 'userdata' OKAY [ 0.243s]
CreateProcess failed: %1 is not a valid Win32 application. (193)
fastboot: error: Cannot generate image for userdata"
I dont know how to proceed with this :crying:
Click to expand...
Click to collapse
Sounds like you're having problems with Windows Defender. I also got the same error messages suddenly once week ago. I did sfc /scannow and all that but all files were intact. After rebooting the PC two times the problem was gone, really strange.
Skickat från min GM1913 via Tapatalk

Anyone here know what fastboot rom i can use to fix my bricked tmobile oneplus 7 pro?

Can you explain this strange effect, please
pitrus- said:
Also it's good to know that the official TWRP of twrp.me does not support Android Q at the moment, that's why you couldn't decrypt and mount the storage. TWRP in Oneplus 7 Pro thread here on XDA does support Q, you just have to remember to boot into the inactive/upgraded slot before booting back to TWRP to flash Magisk as it only installs to the active slot and not the upgraded slot.
Skickat från min GM1913 via Tapatalk
Click to expand...
Click to collapse
After an update to Android Q twrp an root was lost.
I was going the normal way like this:
1. In fastboot boot twrp.img
2. In twrp install twrp.zip
3. Reboot to twrp
4. In twrp install magisk.zip
After this the phone stuck a while on this orange splash screen and then reboot to bootloader.
Reboot --> the same effect
Then:
1. Boot into twrp
2. install twrp.zip
3. Reboot system
Everything ok, but no root
Just one method is working for me:
1. Download the full package of OOS 10.x.x
2. Extract the boot.img
3. Patch boot.img with Magisk
4. Flash on fastboot boot magisk_patched.img
5. reboot
My phone is rooted now but without twrp.
Why can twrp an Magisk not work together?
And why I can´t find any information for this problem on the internet?

Well, since TWRP lives in the boot partition on this phone, you will have to boot TWRP using fastboot boot TWRP. Then you flash the unofficial TWRP build 74 installer zip downloaded from the link below (the one from twrp.me only works on OOS 9 and not 10). Reboot phone back into Magisk to switch slot, flash Magisk installer zip which will then install Magisk to both boot slot a and boot slot b. Reboot phone and you should have both Magisk root and working TWRP.
https://r.tapatalk.com/shareLink/to...2&share_fid=3793&share_type=t&link_source=app
Skickat från min GM1913 via Tapatalk

Fails anyway
Bricked my OnePlus and now I'm left with bootloader (no os, no twrp). Everything leads back to bootloader. Any attempts to apply fastboot boot lead to "Load Error". Now I tried with that tool and ended up with this:
Sending 'odm' (102400 KB) OKAY [ 2.576s]
Writing 'odm' FAILED (remote: '(odb_b) No such partition')
fastboot: error: Command failed
Press any key to exit...
P.S. Full log:
--------------------------------------------
Bootloader Version...:
Baseband Version.....:
Serial Number........: e434a4c8
--------------------------------------------
extracting android-info.txt (0 MB) to RAM...
android-info.txt syntax error: я╗┐require product=msmnile
Setting current slot to 'b' OKAY [ 0.002s]
extracting boot.img (96 MB) to disk... took 0.776s
archive does not contain 'boot.sig'
Sending 'boot_b' (98304 KB) OKAY [ 2.389s]
Writing 'boot_b' OKAY [ 0.406s]
extracting dtbo.img (16 MB) to disk... took 0.151s
archive does not contain 'dtbo.sig'
Sending 'dtbo' (16384 KB) OKAY [ 0.393s]
Writing 'dtbo' OKAY [ 0.047s]
archive does not contain 'dt.img'
archive does not contain 'recovery.img'
extracting vbmeta.img (0 MB) to disk... took 0.001s
archive does not contain 'vbmeta.sig'
Sending 'vbmeta' (8 KB) OKAY [ 0.008s]
Writing 'vbmeta' OKAY [ 0.002s]
archive does not contain 'vbmeta_system.img'
archive does not contain 'super_empty.img'
archive does not contain 'boot_other.img'
extracting odm.img (100 MB) to disk... took 0.395s
archive does not contain 'odm.sig'
Sending 'odm' (102400 KB) OKAY [ 2.576s]
Writing 'odm' FAILED (remote: '(odm_b) No such partition')
fastboot: error: Command failed
Press any key to exit...

I am getting this error, any ideas what is going wrong? (please see attachment)
vegatr0n said:
Hi, I'm writing this to guide those who faced - and will face similar situation in the future - the problem of being stuck on the fastboot screen, where the recovery or booting in EDL is not available.
So, after failing to get root after upgrading to android 10 I was fiddling with TWRP to try to get it to recognize my storage so I can reflash it and flash Magisk, but I couldn't get it to mount the storage, so my stupid brain decided to go to the wipe page and wiped everything in the hope it might magically work!! well.. it didn't!! and I got stuck in the fastboot screen and I thought that I bricked my phone for good.
after hours of searching online and trying everything nothing helped... but finally I managed to fix it.
and btw when I tried to flash TWRP by (fasboot boot twrp.img) I got the following message:
"remote: Failed to load/authenticate boot image: Load Error"
So here is what I did to get my phone working again:
Download and install Tool All in One
Download Fastboot ROM for your phone from here
In the Tool All in One app click on the Flash Factory Images button.
Select the ROM and let it do its work,
hopefully this will work and your device will reboot into a fresh android.
Click to expand...
Click to collapse

[Guide] Installing Custom ROM on Honor Note 10 (EMUI 9)

This thread outlines the exact steps in installing a custom ROM on your Huawei Honor Note 10 device with either EMUI 8 or EMUI 9. You can install and run TWRP on both EMUI and or EMUI 9.
Make sure to follow this guide precisely, as order matters. At the end, I will post an explanation of why we need to execute these steps. I spent an entire weekend of trial and error on my Huawei Honor Note 10, and now I have figured out the ins and outs so you don't have to. You're welcome
Prerequisites
Huawei Honor Note 10 device, either on stock ROM or rooted (doesn't matter)
MicroSD card (formatted exFAT or FAT, doesn't matter)
Bootloader unlock code for Huawei Honor Note 10 (follows a format like my own HBP38K14DBK2RNB4)
Computer with admin privileges
Before You Flash Anything
Back up, back up, back up! I am not responsible if you lose valuable or sensitive data. Your Huawei Honor Note 10 will factory reset a number of times (probably more) before you can get back up and running again. Either use TWRP to do this, or use HiSuite (not recommended but will work on a locked bootloader).
Remove your SIM card! Your carrier may get charged ridiculous amounts of fees if you have a limited data plan, such as 256MB (Canada has notoriously expensive phone plans, so Canadians beware). When you reboot, expect Huawei's stock ROM to use copious amounts of data on retrieving the latest version of bloatware and spyware.
Ensure you have stock recovery installed. If you don't, download the stock recovery image, place it in your Minimal ADB and Fastboot folder, then boot to download mode by holding the VOLUME DOWN button and simultaneously plug in in your Huawei Honor Note 10 device, then open Minimal ADB and Fastboot on your computer and run this command:
Code:
fastboot flash recovery_ramdisk RECOVERY_RAMDIS.img
Steps to Install Custom ROM on Huawei Honor Note 10
Download the EMUI 9 stock ROM and place the dload folder on your MicroSD card
Boot to (stock) recovery by holding down the VOLUME UP, VOLUME DOWN, and POWER buttons at the same time. The update should begin immediately. Wait patiently for your phone to reboot
Fill out the bloatware questionnaire by Huawei and download any and all updates under Settings. This will ensure you have the latest boot image. You will reboot at least once.
Once you have completed all the updates, reboot to download mode; press and hold the VOLUME DOWN button while you plug in your Huawei Honor Note 10 device to your computer
On your computer, download and open Minimal ADB and Fastboot
Run the following command:
Code:
fastboot oem unlock <code>
(where code corresponds to a format that looks like this: HBP38K14DBK2RNB4)
Confirm unlocking your bootloader by using the VOLUME keys, selecting yes, and pressing the POWER button. The Huawei Honor Note 10 device will now perform a factory reset
IMPORTANT step. DO NOT let the Huawei Honor Note 10 reboot. DO NOT. Impatiently wait for the low-level factory reset to complete and as soon as it does, enter download mode again by pressing the VOLUME DOWN key and plugging in the device again
Flash this TWRP recovery:
Code:
fastboot flash recovery_ramdisk HN10_Twrp.img
Reboot to recovery by holding the VOLUME UP and POWER buttons for over 5 seconds. You should see the TWRP logo, and it should boot up. It should boot up right away, so if TWRP hangs here on the TWRP logo, you need to skip back to step 2
IMPORTANT: wipe to factory reset. Wipe /system again via advanced wipe just to be safe
Install any custom ROM you wish via selecting a system image
IMPORTANT: disable_Dm-Verity_ForceEncrypt by installing this zip. If you don't do this, you won't be able to enter TWRP again
Optionally install magisk, titanium backup, and other magisk mods
Reboot system and profit
Update: 2021-04-06​
Reboot to recovery by holding the VOLUME UP and POWER buttons for over 5 seconds. This should boot you to stock RECOVERY.
Wipe to factory reset. Confirm by typing "yes" (WARNING: this wipes your device)
Plug in your Huawei Honor Note 10 to your PC with ADB
Boot to DOWNLOAD mode by holding down the VOLUME DOWN button as soon as your Huawei Honor Note 10 reboots
Flash this TWRP recovery:
Code:
fastboot flash recovery_ramdisk HN10_Twrp.img
Reboot to recovery by holding the VOLUME UP and POWER buttons for over 5 seconds. You should see the TWRP logo, and it should boot up. It should boot up right away, so if TWRP hangs here on the TWRP logo, you need to skip back to step 2
Install any custom ROM you wish via selecting a system image (or zip file if you have EMUI 8)
Install magisk, titanium backup, and other magisk mods (note that you will NOT be able to boot to recovery after this; consider this you last chance to install any mods)
Reboot system and profit
Background and Explanation
When you first flash a ROM, even in EMUI 8, your Huawei Honor Note 10 encrypts /system to prevent third parties such as TWRP from mounting it. Hence, you may successfully boot to TWRP, but /system will be mounted as read-only. This is problematic, as it means you can't install any new ROMs (however, you can make a backup, which can be useful for backing up stock, encrypted /system partitions)
Because /system gets encrypted, it means you have to wipe /system completely. Doing a factory reset (low-level) does this, once you unlock your bootloader. However, if you were to let your Huawei Honor Note 10 boot, then the stock ROM would, by default, encrypt /system, forcing you to start this process all over again (as TWRP will, in most cases, not even boot with an encrypted /system). If your TWRP hangs on the TWRP logo, your /system partition is likely encrypted. You need to factory reset, install TWRP again, and then wipe /system, followed by installing the Disable_Dm-Verity_ForceEncrypt_01.15.2020.zip script.
ROMs I Tested That Work (well)
Resurrection Remix 7 (openKirin)
I hope this guide helps other fellow Huawei Honor Note 10 owners. If you have any questions, please also make sure to include your EMUI version and steps taken so that I can best help you. I hope that I have saved some of you trouble when updating to EMUI 9 and also helped to explain why updating can become so tedious.

Thank you for the instructions! I've got some questions...
ForgottenSolstace said:
IMPORTANT: wipe to factory reset. Wipe /system again via advanced wipe just to be safe
Install any custom ROM you wish via selecting a system image
Click to expand...
Click to collapse
During these steps, I saw the error messages like these:
Code:
Updater process ended with ERROR:7
Error installing zip file '/sdcard/RR-P-v7.0.2-20200202-ravel-Unoffical.zip'
and
Code:
Failed to mount '/cust' (Invalid argument)
Failed to mount '/vendor' (Invalid argument)
Failed to mount '/odm' (Invalid argument)
Failed to mount '/product' (Invalid argument)
I tried getting into fastboot mode and flash the CUST.img, VENDOR.img, ODM.img and PRODUCT.img but failed with the error message "FAILED (remote: Command not allowed)", what should I do?

null00005 said:
Thank you for the instructions! I've got some questions...
During these steps, I saw the error messages like these:
Code:
Updater process ended with ERROR:7
Error installing zip file '/sdcard/RR-P-v7.0.2-20200202-ravel-Unoffical.zip'
and
Code:
Failed to mount '/cust' (Invalid argument)
Failed to mount '/vendor' (Invalid argument)
Failed to mount '/odm' (Invalid argument)
Failed to mount '/product' (Invalid argument)
I tried getting into fastboot mode and flash the CUST.img, VENDOR.img, ODM.img and PRODUCT.img but failed with the error message "FAILED (remote: Command not allowed)", what should I do?
Click to expand...
Click to collapse
Yep, so it sounds like you have an encrypted /data.
Make sure you can safely wipe the entire device, then try the following in download mode:
Bash:
fastboot erase userdata
(Note: this will erase everything on /data)
Then boot to TWRP again. Check the logs and try again.

ForgottenSolstace said:
Yep, so it sounds like you have an encrypted /system.
Make sure you can safely wipe the entire device, then try the following in download mode:
Bash:
fastboot erase userdata
Then boot to TWRP again. Check the logs and try again.
Click to expand...
Click to collapse
How do I wipe the entire device? I have done step 8 properly (get into fastboot immediately after low-level factory reset completes) and wiped system in TWRP, but still get the error messages.

null00005 said:
How do I wipe the entire device? I have done step 8 properly (get into fastboot immediately after low-level factory reset completes) and wiped system in TWRP, but still get the error messages.
Click to expand...
Click to collapse
Bash:
fastboot erase userdata
That will wipe /data.
Since you can also boot to TWRP, then try wiping /system, cache, and dalvik (factory reset). If you can also wipe /data, then that might also work in TWRP, depending on which version you're using.

ForgottenSolstace said:
Bash:
fastboot erase userdata
That will wipe /data.
Since you can also boot to TWRP, then try wiping /system, cache, and dalvik (factory reset). If you can also wipe /data, then that might also work in TWRP, depending on which version you're using.
Click to expand...
Click to collapse
After reinstalling the stock ROM and unlock bootloader and flash TWRP again, I performed "fastboot erase system" and "fastboot erase userdata" in fastboot, then wiped Dalvik, cache, Cust, Data, system, Product and Version in TWRP. However, I am still getting the "Failed to mount '/odm' (Invalid argument)" error message
I can't wipe odm in TWRP since there is no such option, and I can't perform "fastboot erase odm" as it shows up an error message saying "FAILED (remote: Command not allowed)". What should I do now?

null00005 said:
After reinstalling the stock ROM and unlock bootloader and flash TWRP again, I performed "fastboot erase system" and "fastboot erase userdata" in fastboot, then wiped Dalvik, cache, Cust, Data, system, Product and Version in TWRP. However, I am still getting the "Failed to mount '/odm' (Invalid argument)" error message
I can't wipe odm in TWRP since there is no such option, and I can't perform "fastboot erase odm" as it shows up an error message saying "FAILED (remote: Command not allowed)". What should I do now?
Click to expand...
Click to collapse
If you roll back to stock and unlock your bootloader again, then you don't need to do fastboot erase userdata because "factory reset low-level" will perform that once you unlock your bootloader again. So you should be able to flash TWRP, boot fine (only that one time), install whatever ROM you want, flash magisk, and boot (note: on EMUI9, you must reboot to recovery, as boot_ramdisk only exists in EMUI8).
In the past, I have ignored the message "failed to mount '/odm'" and still had success; just pay attention to the status code at the end when you install /system. Don't bother wiping odm, as we really care about mounting /system. Perform a factory reset just to be safe, and feel free to wipe /data, but it won't matter if you already performed a factory-reset (low-level) from unlocking your bootloader again.
Try installing your ROM of choice from TWRP despite this error, flashing magisk, and confirm if that works.

ForgottenSolstace said:
This thread outlines the exact steps in installing a custom ROM on your Huawei Honor Note 10 device with either EMUI 8 or EMUI 9. You can install and run TWRP on both EMUI and or EMUI 9.
ROMs I Tested That Work (well)
Resurrection Remix 7 (openKirin)
Click to expand...
Click to collapse
Hi, how about root with magisk in this rom?!

TheFastGT said:
Hi, how about root with magisk in this rom?!
Click to expand...
Click to collapse
I second that. Magisk installed in boot.img but ROM doesn't recognize root, installing SuperSU says done but no result. Once I got SuperSU to get into stage where it said that boot might take longer and it was recognized but I can't replicate that anymore.

jazzzy said:
I second that. Magisk installed in boot.img but ROM doesn't recognize root, installing SuperSU says done but no result. Once I got SuperSU to get into stage where it said that boot might take longer and it was recognized but I can't replicate that anymore.
Click to expand...
Click to collapse
Just done....you need to install magisk in this:
RECOVERY_RAMDIS.img
then flash via fastboot and reboot...

TheFastGT said:
Just done....you need to install magisk in this:
RECOVERY_RAMDIS.img
then flash via fastboot and reboot...
Click to expand...
Click to collapse
so I open Magisk app and patch RECOVERY_RAMDIS.img, then flash RECOVERY_RAMDIS.img and after that flash TWRP ? TWRP won't overwrite RECOVERY_RAMDIS.img ?

jazzzy said:
so I open Magisk app and patch RECOVERY_RAMDIS.img, then flash RECOVERY_RAMDIS.img and after that flash TWRP ? TWRP won't overwrite RECOVERY_RAMDIS.img ?
Click to expand...
Click to collapse
I've a Honor Note 10 and i haven't TWRP installed, i use stock recovery and Openkirin rom...

How can I unlock my bootloader?

Darj said:
How can I unlock my bootloader?
Click to expand...
Click to collapse
HCU client

TheFastGT said:
HCU client
Click to expand...
Click to collapse
Thanks.. this is the only device I have so I wanted to ask what would happen if I mess it up

TheFastGT said:
HCU client
Click to expand...
Click to collapse
And once I unlock the bootloader using HCU client, do I have to follow the steps above or can I just install a custom recover how you'd do on any phone?

@Darj , did you manage to sort out rooting your Huawei Honor Note 10? I've updated the installation steps to reflect the shortened steps I last took to get Magisk running (downgraded to EMUI8 on my Huawei Honor Note 10 to try to preserve TWRP).
Hopefully, we'll see more ROMS from the OpenKirin project, as the latest security patch is almost a year old on EMUI8.

@ForgottenSolstace not yet. I want to make sure I have all the informations I need before spending money to unlock the bootloader

@Darj , it only costs 15USD to unlock your Huawei Honor Note 10. Why not go ahead and try?
I assure you that the effort is much worth it; Stock ROM is bloated with all kinds of spyware from the Chinese government. When you install AOSP, you can actually secure your phone following the updated instructions which encrypts /data.
Let me know if you have any questions. Happy to help

Hi ...got problem using twrp?

Not allowed to flash recovery anymore?

I am trying to flash the LineageOS recovery for LineageOS 18. I have previously already installed LineageOS 17 on my phone with no issues like 2 or 3 weeks ago. However, I am now trying to update to LineageOS 18 and I am now not allowed to flash the new recovery to my phone. Nothing has changed since I was last able to flash a recovery to my phone except I just changed my battery out today (since the old one was faulty), but I doubt that would interfere with the software or firmware, right? I have verified my phone is unlocked, I have verified my ADB and Pixel drivers are all up to date, and I have tried flashing on two computers, Linux and Windows. An additional thing to note that may or may not give you a clue as to what is going on is that I am able to boot into a TWRP img, but it no longer prompts me for a decryption password, and when I go to mount > decrypt and enter my pin, it says the password is incorrect.
You guys got any clue how I can fix this?
EDIT:
Here is my terminal output:
Code:
[[email protected] ~]$ sudo fastboot flash recovery /home/chris/Downloads/lineage-18.1-20210409-microG-coral-recovery.img
[sudo] password for user:
Sending 'recovery' (65536 KB) OKAY [ 1.710s]
Writing 'recovery' FAILED (remote: 'Not allowed to flash (recovery)')
fastboot: error: Command failed
I have to use sudo because it doesnt detect my device when I dont use sudo for some dumbass reason...

Deleted

cray12399 said:
I am trying to flash the LineageOS recovery for LineageOS 18. I have previously already installed LineageOS 17 on my phone with no issues like 2 or 3 weeks ago. However, I am now trying to update to LineageOS 18 and I am now not allowed to flash the new recovery to my phone. Nothing has changed since I was last able to flash a recovery to my phone except I just changed my battery out today (since the old one was faulty), but I doubt that would interfere with the software or firmware, right? I have verified my phone is unlocked, I have verified my ADB and Pixel drivers are all up to date, and I have tried flashing on two computers, Linux and Windows. An additional thing to note that may or may not give you a clue as to what is going on is that I am able to boot into a TWRP img, but it no longer prompts me for a decryption password, and when I go to mount > decrypt and enter my pin, it says the password is incorrect.
You guys got any clue how I can fix this?
EDIT:
Here is my terminal output:
Code:
[[email protected] ~]$ sudo fastboot flash recovery /home/chris/Downloads/lineage-18.1-20210409-microG-coral-recovery.img
[sudo] password for user:
Sending 'recovery' (65536 KB) OKAY [ 1.710s]
Writing 'recovery' FAILED (remote: 'Not allowed to flash (recovery)')
fastboot: error: Command failed
I have to use sudo because it doesnt detect my device when I dont use sudo for some dumbass reason...
Click to expand...
Click to collapse
There is no "recovery" partition anymore, it is in the boot.img. The "recovery" is a virtual partition that doesnt exist as its own partition. Review the steps in LOS 18.1 and it points out to flash the boot.img, then reboot to recovery once you have flashed boot.img and rebooted
Reboot to bootloader
Flash the provided boot.img to both slots (fastboot flash --slot all boot boot.img)
Reboot into recovery and factory reset for initial install
Sideload the latest build of Lineage OS (adb sideload lineage.zip)
I will also note that you seem to be using the MicroG (no GAPPs) version so I dont know if the steps are different than official LOS, but I dont think so. I would follow the dev steps to the T and not try older methods (I did the same thing I am warning against), I used my old and trusty, time tested steps, that always worked in previous devices, but do not anymore on Pixels.
It sounds like whatever happened broke your decryption of /data (but its a guess without knowing more). You might be stuck and need to format /data, or you can try to sideload the update and see if it works. Without enough info, I am guessing so provide more info and we can try to help better.
Also to note, if you use the boot.img / sideload method, you do not need TWRP, nor to mount anything. Its all done from the "native recovery" provided by LOS but you might have screwed up the/data decryption, IDK.
If this were me, and in your shoes, I would restore a FULL FACTORY image (not an OTA) with the -W left intact on BOTH slots so it rewrites my partition layout and undoes whatever funkiness' happened. You would lose everything, but it would get you back into working shape.
If you do not want to start over (and I dont disagree, it sucks), then follow the TWRP forum for coral (PX4):
TWRP Coral [Official]
[RECOVERY] TWRP 3.5.0_10-0 - TeamWin Recovery Project [/B] Introduction: Team Win Recovery Project or TWRP for short, is a custom recovery built with ease of use and customization in mind. We started from the ground up by taking AOSP...
forum.xda-developers.com

GROOVYJOSHCLARK said:
There is no "recovery" partition anymore, it is in the boot.img. The "recovery" is a virtual partition that doesnt exist as its own partition. Review the steps in LOS 18.1 and it points out to flash the boot.img, then reboot to recovery once you have flashed boot.img and rebooted
Reboot to bootloader
Flash the provided boot.img to both slots (fastboot flash --slot all boot boot.img)
Reboot into recovery and factory reset for initial install
Sideload the latest build of Lineage OS (adb sideload lineage.zip)
I will also note that you seem to be using the MicroG (no GAPPs) version so I dont know if the steps are different than official LOS, but I dont think so. I would follow the dev steps to the T and not try older methods (I did the same thing I am warning against), I used my old and trusty, time tested steps, that always worked in previous devices, but do not anymore on Pixels.
It sounds like whatever happened broke your decryption of /data (but its a guess without knowing more). You might be stuck and need to format /data, or you can try to sideload the update and see if it works. Without enough info, I am guessing so provide more info and we can try to help better.
Also to note, if you use the boot.img / sideload method, you do not need TWRP, nor to mount anything. Its all done from the "native recovery" provided by LOS but you might have screwed up the/data decryption, IDK.
If this were me, and in your shoes, I would restore a FULL FACTORY image (not an OTA) with the -W left intact on BOTH slots so it rewrites my partition layout and undoes whatever funkiness' happened. You would lose everything, but it would get you back into working shape.
If you do not want to start over (and I dont disagree, it sucks), then follow the TWRP forum for coral (PX4):
TWRP Coral [Official]
[RECOVERY] TWRP 3.5.0_10-0 - TeamWin Recovery Project [/B] Introduction: Team Win Recovery Project or TWRP for short, is a custom recovery built with ease of use and customization in mind. We started from the ground up by taking AOSP...
forum.xda-developers.com
Click to expand...
Click to collapse
Where are you getting the boot.img for lineage? I don't see one anywhere. All I've seen is recovery.img as me the rom zip.
Thanks in advance Josh.

flash713 said:
Where are you getting the boot.img for lineage? I don't see one anywhere. All I've seen is recovery.img as me the rom zip.
Thanks in advance Josh.
Click to expand...
Click to collapse
If using the official, it's provided in the download section. If not, and it's unofficial, then usually the devs of that ROM provide it. If that's not being done by the devs of the version you are using, then you need to use python and dumper script. It uses python and script (dumper) to pull out the boot.img from the payload.bin (within the zip).
Just keep in mind that I do not use the MicroG version so it's possible the steps vary but I doubt it. What I stated above is usually the method for custom, LOS, even official firmware versions to pull out the boot.img.
Send me the link to download what you're using to try and reproduce it so I can advise better (ROM/recovery/ETC).

Question I might have bricked my phone, I need help

I am just new to this flashing custom roms or firmware and twrp also. And dumb enough to not back it up.
I wanted to install arrow os in my phone. When I was about to wipe data, cache and dalvik, I accidentally checked metadata also and wiped. Then problems created more problems.
problems right now:
I cant put a file in my storage
Internal Storage is just blank on my pc
No OS
TWRP on both slots
please help me i really needed help and knowledge about it
I hope the attachment helps
EDIT--
Solutions to my problems:
WHEN you softbrick your phone and you only have fastboot and nothing else
Thanks to this guy..
SOLUTION: download your original firmware but choose the fastboot one and not recovery after download just unzip. Double click flash_all.bat and its back to square one.
WHEN you dont know how to flash or the file you have is .img
SOLUTION: find a guide in xda because apparently you can install a .img file in "fastbootd" mode
the guides here: https://forum.xda-developers.com/t/...sues-all-without-any-custom-recovery.4337099/
COMMENT: not the usual thats what on top of youtube search.
WHEN you see errors in twrp/orangefox recovery you might get panic and search for solution.
COMMENT: try to find and use a solution that doesnt delete something first. In my experience it got bricked even more.
Thanks to the people who commented back on my post and helping me get to know what to do next.

Try putting the stock ROM on a SD card or usb (if you have a dongle).

georg3_ said:
Try putting the stock ROM on a SD card or usb (if you have a dongle).
Click to expand...
Click to collapse
SD card that you put on beside the sim? if yes
Do I download stock ROM in official website? Cus I dont have 1 right now
then flashing it there by using twrp? is that how its gonna run? because i really dont wanna assume and create another problem

Try flashing this stock ROM (global) from a SD card, in TWRP. It's a recovery package, so you can install it as any zip.
Also, can you boot into fastboot/bootloader from TWRP?

Plus, where did you get the ArrowOS image? There are no builds, official or not.

georg3_ said:
Plus, where did you get the ArrowOS image? There are no builds, official or not.
Click to expand...
Click to collapse
I found it here
It is made my myst33d and it is a beta build
im getting a sd card right now to test it out
And yes I still can go to fastboot/bootloader from twrp

I cant seem to find my file in twrp... even in file manager
the file is int .tgz must I change it to .zip?

raikiro1 said:
I cant seem to find my file in twrp... even in file manager
Click to expand...
Click to collapse
Is the twrp detecting your sd card？try click on the Install image and change to install zip

can you sideload?

I can now see it, I think I reflashed twrp, now I can, but I cant install because of failed to mount system_root and I have done change file system of data to Ext4. when it resets it comes back to f2fs
edit: change file system of data to Ext4 failed
edit2: thank you guys really for commenting back and helping me
is no verity affecting it? cus I am not able to install it now

you should format data and put the arrow build in it, maybe it will work

J6idot said:
you should format data and put the arrow build in it, maybe it will work
Click to expand...
Click to collapse
I have changed the data to Ext4, fomarted, wiped again the data,dalvik and cache
I have a Redmi Note 10S Rosemary from xiaomiupdater but I still cannot install the rom cus there is a error " Error installing zip file /sdcard1/thefile."
I tried to install no verity opt encrypt but failed and says updater process ended with ERROR: 1
Error installing zip file "sdcard1/thefile"

raikiro1 said:
I cant seem to find my file in twrp... even in file manager
the file is int .tgz must I change it to .zip?
Click to expand...
Click to collapse
Must change it to zip.
EDIT: Extract the file, there's a zip or img inside.

raikiro1 said:
I have changed the data to Ext4, fomarted, wiped again the data,dalvik and cache
I have a Redmi Note 10S Rosemary from xiaomiupdater but I still cannot install the rom cus there is a error " Error installing zip file /sdcard1/thefile."
I tried to install no verity opt encrypt but failed and says updater process ended with ERROR: 1
Error installing zip file "sdcard1/thefile"
Click to expand...
Click to collapse
Try to sideload it, maybe it'll work.

georg3_ said:
Must change it to zip.
Click to expand...
Click to collapse
Should have said "extract the file, there's a zip or img inside", don't change the file extension.

Update: I found the guide how to sideload ... just change the Ext4 to F2fs
[Tutorial] TWRP ADB Sideloading
Alternative solution: OTG usb flash drive - With one of these, you can store a ROM zip safely, and still format ‘userdata’ to f2fs or EXT4. TWRP ADB Sideloading Requirements: Mac | Linux | Windows PC / Laptop and TWRP Custom Recovery Moto G...
forum.xda-developers.com
and I was able to sideload it and then got MIUI finally
what worried me is there were still errors like system_root, vendor and product... and its running fine now I guess but im back on track to make it to arrow OS.... I hope no mistakes this time like deleting metadata.
Thank you all who replied to this post , I really do. Thank you

raikiro1 said:
Update: I found the guide how to sideload ... just change the Ext4 to F2fs
[Tutorial] TWRP ADB Sideloading
Alternative solution: OTG usb flash drive - With one of these, you can store a ROM zip safely, and still format ‘userdata’ to f2fs or EXT4. TWRP ADB Sideloading Requirements: Mac | Linux | Windows PC / Laptop and TWRP Custom Recovery Moto G...
forum.xda-developers.com
and I was able to sideload it and then got MIUI finally
what worried me is there were still errors like system_root, vendor and product... and its running fine now I guess but im back on track to make it to arrow OS.... I hope no mistakes this time like deleting metadata.
Thank you all who replied to this post , I really do. Thank you
Click to expand...
Click to collapse
no problem next time installing, stick to sideloading, less room for error

I cant seem to install TWRP recovery again it justs bootloop .. I dont know why anybody knows?
Whenever I fastboot boot twrp3.6.1-rosemary it fails, says too many links, and when I fastboot reboot recovery it boot loops
flashboot flash boot twrprosemary says okay in slot A and I even put it to B and flash it there sadly
the problem might be because its A12 ... just an update

raikiro1 said:
I cant seem to install TWRP recovery again it justs bootloop .. I dont know why anybody knows?
Whenever I fastboot boot twrp3.6.1-rosemary it fails, says too many links, and when I fastboot reboot recovery it boot loops
flashboot flash boot twrprosemary says okay in slot A and I even put it to B and flash it there sadly
the problem might be because its A12 ... just an update
Click to expand...
Click to collapse
A12 shouldn't be a problem.
Probably you should flash another vbmeta.img.
OR
I don't know if there is an .img twrp around, but if there is you can:
Code:
fastboot boot {recovery.img}
and then [Advanced]>[Install Recovery Ramdisk].

raikiro1 said:
I cant seem to install TWRP recovery again it justs bootloop .. I dont know why anybody knows?
Whenever I fastboot boot twrp3.6.1-rosemary it fails, says too many links, and when I fastboot reboot recovery it boot loops
flashboot flash boot twrprosemary says okay in slot A and I even put it to B and flash it there sadly
the problem might be because its A12 ... just an update
Click to expand...
Click to collapse
what vbmeta are you using?