My screen show danger signal - Android Auto General

Hi everybody,
I have a Erisin 2046 with RK3188 and 1024x600 screen it came with android 4.4.4 kitkat but a long time ago I changed it for Android 5.1.1 Malaysk (thank you!) It run fine about 1,5 years but right now while I'm driving sometimes music reduce volume and display show a yellow danger signal after 1-2 seconds it disapear and all work fine
Somebody know what could happen? Or where can I start to check?
Thank you

Not sure but kind if sounds like your switching into reverse mode. Reduced gain is something that happens when reversing and it switches to backup camera. Do you have a backup camera installed? If not, try unhooking the reverse wire on your headunit harness. Maybe just hardware failure it is an older unit.

Related

Calibrate accelerometer and/or gyroscope

Hi!
I am facing problems with the orientation sensors (accelerometer and/or gyroscope), because installing several applications to test them (or use games), it is clearly observable, that they are a bit off (with enough to be disturbing when required). For example, games or tests that simulate a ball, and my phone is laying on a horizontal table, the ball rolls quickly to the edge of screen. This happens as well with the built-in tests in the "service menu" of the phone, for accelerometer and gyroscope also.
Do you have any suggestions how could I calibrate these sensors globally (for every app)?
Thanks.
Info
vetko said:
Hi!
I am facing problems with the orientation sensors (accelerometer and/or gyroscope), because installing several applications to test them (or use games), it is clearly observable, that they are a bit off (with enough to be disturbing when required). For example, games or tests that simulate a ball, and my phone is laying on a horizontal table, the ball rolls quickly to the edge of screen. This happens as well with the built-in tests in the "service menu" of the phone, for accelerometer and gyroscope also.
Do you have any suggestions how could I calibrate these sensors globally (for every app)?
Thanks.
Click to expand...
Click to collapse
factory Reset ur phone and then use PC companion app to Repair Firmware...
this can wipe current data and install fresh firmware on ur device
:good:
Hi,
I have the same problem. Only the x axis of the accelerometer seems to be affected : it show a value around 1 instead of 0 while the phone is sitting flat. Y and Z display normal values.
All the software solutions I have tried have had no effect at all... It seems the built-in test reads raw data from the accelerometer. It is hard to imagine how this can be a hardware problem though...
Anyway, in my case I believe a software fix (x=x-1) would do the trick but I have no idea how to do such a thing ! Any help ?
@vekto : Have you solved the issue by any chance ?
Would anyone care to try the accelerometer tests and post their results ?
Typing *#*#7378423#*#* will get you on the service menu. The two significant tests are "accelerometer" and "gyroscope".
I'd post some screenshots myself but I'm not allowed yet...
I'm having the same problem now. It seems one axis is affected. Haven't found a way around so far. This is sad because it affects the images taken with Google Camera Sphere mode. The images are badly aligned together with glitches in between. My phone wasn't like this before.
Either a SW fault - might be able to calibrate with GPS Status & Toolbox app, for example - or a FW fault - and reflashing ROM might help (highly unlikely) - or HW fault - the sensor has moved on the board (which is a bad sign anyway, might be on the way to disconnecting itself).
I sent mine to Xperia Care and got it back with the accelerator fixed. Still unclear if it's a HW problem...
It came back with a white spot on the screen (near the power button) though... so I sent it back again
I'm also having issues with the gyroscope. Installed Bubble app to calibrate the gyro. It showed the gyro was of a couple of degrees. Unfortunately the bubble app calibration doesn't work in a game like Need for Speed. It's very difiicult to achieve good times in the game right now since I have to hold it tilted to the left to go straight ahead.
So if anyone has a fix or workaround... Please do post.
Same problem, Seems after factory reset whith wipe dalvik cache.
any solution?
02nd March 2017, my autorotate has completely stopped working, restart, safe-deposit and reset do not fix. Diagnostics show Gyroscope Light Sensor and accelerometer failed testing, 3 years of same issue, surely there must be a fix that works by now?? ( please note, " turning it off and on again " does not fix it )
Helps Please
I have the same issue. Since last week, gyro, accelerometer, light and proximity sensors stop working. I've tried reflashing stock ROM without success. I have not warranty (almost 3 years old), so I even try to disassemble , disconnect an reconnect every flex (I don't know exactly were the sensors are located on the board). After that I get almost 8 hours of fully functionally sensors and then, they stop working again, so I'm almost sure it's a hardware issue.
Same problem for 3 years
I'm just now getting around to doing something about this. As my power button stopped working I can't post requested screenshot without going to the pc. I have been shopping new (fall 2018) phones after having the Z3+ since release. In my research I'm finding the phone still is better than Samsung, LG, and the pixel3 for me because the 3.5mm phone jack is mandatory for me using my device with an i-rig midi requiring both that port and the USB at the same time. I'm going to do everything I can to keep using this phone till it falls to dust. It's one of 4 Sony I've bought since the day Z1 came out of t-mo. I look forward to testing solutions. :good:
Some time after my post, I bought a new jack/proximity sensor flex and replace it. This solved the issue, but weeks later, the bottom portion of the touch screen becomes unresponsive. May be I have done something wrong... may be programmed obsolescence...
Hi I'm facing a problem of my gyroscope I don't know which one is not working a gyroscope or accelerometer. My gyroscope is so delay when I play pubg mobile and I can't also calibrate my Gsensor it always says FAIL but I put in a perfect flat surface please please please help me with this problems

Proper Android Auto headunits

Have just returned my Xtrons unit due to various issues, and looking to change it for a proper Android Auto unit.
Had a look at the Pioneer AVH-X8700BT and quite disappointed, horrible buttons and a creaky flexy facia, and the onscreen menus etc are cluttered and unintuitive. This is a shame as I could have got 20%/£100 off in Halfords.
So interested to hear from anyone who has tried the others. I keep seeing comments about a JBL unit but it seems the launch date keeps getting shoved back. Kenwood - I've not found much about these but not hugely impressed by the look of the on screen menus in the static photos.
The one that has really got my attention is the Sony XAV-AX100 that has supposedly just been released. The unit looks smart and doesn't appear to need neon footwell lamps and extra boost gauges to complement it, (!) and the Sony menus have similar clean/uncluttered look like the Android Auto section. Apparently its only available via Sony Centres and both my local stores haven't come back yet with availability
I agree with your analysis of the options but i don't think the Sony product is released until December:
https://www.amazon.co.uk/exec/obidos/ASIN/B01LY8222N/geizhals07-21/ref=nosim?m=A3P5ROKL5A1OLE
I personally got the Pioneer F88DAB (which is a european model) and I like the way it works. the menu is working quite well and I like the fact that I am able to adjust the screen tilt.
Android Auto works great at the device and I will upload a video of the device with android auto, so you can see how the menu and all the functions look like.
amazon
that JBL has been pushed back so many times, I would not have any faith in it. The top of the line Kenwood is over a grand, but I have seen some really good reviews on it and few bad reviews. That was my backup plan if I didn't like my Joying, but I love my Joying
Sir_Nomad49 said:
I personally got the Pioneer F88DAB ...amazon
Click to expand...
Click to collapse
At £850, it's poor value - you could professionally install a tablet for a lot less. I think I'll wait for the Sony for x-mas
kc1 said:
At £850, it's poor value - you could professionally install a tablet for a lot less. I think I'll wait for the Sony for x-mas
Click to expand...
Click to collapse
That is true, but it was easier to install and I personally like the interface of it.
The Sony is a good choice. With a pioneer device you can use appradio or mirra cast.
When I am home, I will upload a video on how it is usable.
Sent from my SM-N9005 using XDA Free mobile app
kc1 said:
I agree with your analysis of the options but i don't think the Sony product is released until December:
https://www.amazon.co.uk/exec/obidos/ASIN/B01LY8222N/geizhals07-21/ref=nosim?m=A3P5ROKL5A1OLE
Click to expand...
Click to collapse
I'm also looking forward to getting the Sony unit later this year. :good:
CayenneGTS said:
I'm also looking forward to getting the Sony unit later this year. :good:
Click to expand...
Click to collapse
Looks like it's available to order now
http://amzn.eu/1V2elbz
http://a.co/byhPOFu
Sir_Nomad49 said:
I personally got the Pioneer F88DAB (which is a european model) and I like the way it works. the menu is working quite well and I like the fact that I am able to adjust the screen tilt.
Android Auto works great at the device and I will upload a video of the device with android auto, so you can see how the menu and all the functions look like.
amazon
Click to expand...
Click to collapse
I have the previous model the Pioneer F77 DAB. Works very well. Back in the day halfords had it for something over £800 then by accident halfords listed at £600 so reserved one sharpish. Couple of days later it was back at its original price. I think someone had cocked up.
Far as android auto is concerned it works faultlessly. It's pretty quick booting up from off and reverse camera works straight away, not having to wait for unit to boot. Occasionally when turning vehicle key to on unit comes on as normal but if you then hesitate to start engine it seems to crash and take maybe a minute to boot again. Even reverse camera does not work when this happens. Unit comes on when key is turned to power but cranking engine robs power from unit so it turns off and on again. The crash is something to do with the stage of boot when power drops. In all the time I've had it, it has only happened maybe half a dozen times. Other than this it works faultlessly. Pioneer want stupid money for mapping updates for the built in satnav on the downside but half the time I use Google maps in AA for quickness. Pioneer has an app to connect the phone to on board sat navigation - AVICSYNC. It works but is very clunky. Waiting for Waze to become AA compatible but not holding my breath on that one.
Well after failing miserably with two local Sony centres and also Sony online, I managed to find the unit for sale on Amazon! I'd set my heart on it and after three months with a gaping hole in the dashboard, its finally fitted!
First of all, its single DIN behind the facia so plenty of room for wiring looms, and simply slides in unlike the Android units that would need 30 minutes of trying to pull the cables around and still failing to get the facia flush. Also, as expected, it comes with a cage and standard mounting brackets so no bodging needed. Once fitted the unit sits neatly within the existing double din facia.
It starts up fast, works with my factory fitted reversing camera (unlike the Android units) and is simple to navigate. I was concerned about the 'cheap' resistive screen, but its actually very responsive and only needs a light touch.
The only issues I have so far;
1) The volume control knob needs a fair bit of spinning, it needs two or three goes to crank the volume down. I need to check the settings again to see if you can make the adjustment less fine.
2) If I connect the phone and play music on Spotify, and then start the engine, the unit powers down as normal during engine start. When it resumes, the music starts playing on the phone...I have to swipe across to a second screen and press a '+' speaker button to get the audio back through the vehicle speakers. A bug with my phone, or the radio? Something to look in to.
3) There is a limit to how many menu presses you can navigate, and unlike running Android Auto on the phone, instead of a momentary warning, it sticks until you navigate back home. Thats fine, although really irritating if your passenger is trying to find some tunes. But it does the same when stationary...I'm sure my handbrake is wired correctly but regardless, I'll be over-riding that feature as its in a campervan and I normally have a passenger!
4) Just to answer my own questions about the unit; No, the facia is not removable. No, it doesn't come with a remote control (a shame for a campervan!) And unlike the Android units, everything works seamlessly. i.e it doesn't freeze or get laggy, you don't need to wait ages for the unit to boot or Google Maps to load, and if you start the radio, Spotify etc will stop, rather than having two lots of audio competing for your attention
Spooky_b329 said:
3) There is a limit to how many menu presses you can navigate, and unlike running Android Auto on the phone, instead of a momentary warning, it sticks until you navigate back home. Thats fine, although really irritating if your passenger is trying to find some tunes. But it does the same when stationary...I'm sure my handbrake is wired correctly but regardless, I'll be over-riding that feature as its in a campervan and I normally have a passenger!
Click to expand...
Click to collapse
Android Auto uses the phones GPS and maybe accelerometer to know when you've stopped.
On my Kenwood unit the handbrake sensor is grounded all the time and I still get that message.
Spooky_b329 said:
Well after failing miserably with two local Sony centres and also Sony online, I managed to find the unit for sale on Amazon! I'd set my heart on it and after three months with a gaping hole in the dashboard, its finally fitted!
First of all, its single DIN behind the facia so plenty of room for wiring looms, and simply slides in unlike the Android units that would need 30 minutes of trying to pull the cables around and still failing to get the facia flush. Also, as expected, it comes with a cage and standard mounting brackets so no bodging needed. Once fitted the unit sits neatly within the existing double din facia.
It starts up fast, works with my factory fitted reversing camera (unlike the Android units) and is simple to navigate. I was concerned about the 'cheap' resistive screen, but its actually very responsive and only needs a light touch.
The only issues I have so far;
1) The volume control knob needs a fair bit of spinning, it needs two or three goes to crank the volume down. I need to check the settings again to see if you can make the adjustment less fine.
2) If I connect the phone and play music on Spotify, and then start the engine, the unit powers down as normal during engine start. When it resumes, the music starts playing on the phone...I have to swipe across to a second screen and press a '+' speaker button to get the audio back through the vehicle speakers. A bug with my phone, or the radio? Something to look in to.
3) There is a limit to how many menu presses you can navigate, and unlike running Android Auto on the phone, instead of a momentary warning, it sticks until you navigate back home. Thats fine, although really irritating if your passenger is trying to find some tunes. But it does the same when stationary...I'm sure my handbrake is wired correctly but regardless, I'll be over-riding that feature as its in a campervan and I normally have a passenger!
4) Just to answer my own questions about the unit; No, the facia is not removable. No, it doesn't come with a remote control (a shame for a campervan!) And unlike the Android units, everything works seamlessly. i.e it doesn't freeze or get laggy, you don't need to wait ages for the unit to boot or Google Maps to load, and if you start the radio, Spotify etc will stop, rather than having two lots of audio competing for your attention
Click to expand...
Click to collapse
Re "And unlike the Android units, everything works seamlessly", not true - please see your points 1 and 2 !!
Re "unlike the Android units . . . it doesn't freeze or get laggy, you don't need to wait ages for the unit to boot or Google Maps to load", Android units per se dont have this problem, one particular type, with only 1GB RAM, Lollipop and a later version of Google Maps does, this can easily be sorted.
Glad youre happy with your new unit, enjoy.
Spooky_b329 said:
Well after failing miserably with two local Sony centres and also Sony online, I managed to find the unit for sale on Amazon! I'd set my heart on it and after three months with a gaping hole in the dashboard, its finally fitted!
First of all, its single DIN behind the facia so plenty of room for wiring looms, and simply slides in unlike the Android units that would need 30 minutes of trying to pull the cables around and still failing to get the facia flush. Also, as expected, it comes with a cage and standard mounting brackets so no bodging needed. Once fitted the unit sits neatly within the existing double din facia.
It starts up fast, works with my factory fitted reversing camera (unlike the Android units) and is simple to navigate. I was concerned about the 'cheap' resistive screen, but its actually very responsive and only needs a light touch.
The only issues I have so far;
1) The volume control knob needs a fair bit of spinning, it needs two or three goes to crank the volume down. I need to check the settings again to see if you can make the adjustment less fine.
2) If I connect the phone and play music on Spotify, and then start the engine, the unit powers down as normal during engine start. When it resumes, the music starts playing on the phone...I have to swipe across to a second screen and press a '+' speaker button to get the audio back through the vehicle speakers. A bug with my phone, or the radio? Something to look in to.
3) There is a limit to how many menu presses you can navigate, and unlike running Android Auto on the phone, instead of a momentary warning, it sticks until you navigate back home. Thats fine, although really irritating if your passenger is trying to find some tunes. But it does the same when stationary...I'm sure my handbrake is wired correctly but regardless, I'll be over-riding that feature as its in a campervan and I normally have a passenger!
4) Just to answer my own questions about the unit; No, the facia is not removable. No, it doesn't come with a remote control (a shame for a campervan!) And unlike the Android units, everything works seamlessly. i.e it doesn't freeze or get laggy, you don't need to wait ages for the unit to boot or Google Maps to load, and if you start the radio, Spotify etc will stop, rather than having two lots of audio competing for your attention
Click to expand...
Click to collapse
My unit came with a remote. I also find what I believe is a software bug, if you turn on the dimmer the maps will always be in night mode.
leonkernan said:
Android Auto uses the phones GPS and maybe accelerometer to know when you've stopped.
On my Kenwood unit the handbrake sensor is grounded all the time and I still get that message.
Click to expand...
Click to collapse
I've got the same issue. As of 2.0 Android Auto uses the head units' GPS data. If your head unit doesn't have built in navigation (GPS), it won't remove the limitation even if stationary.
Link: https://productforums.google.com/d/msg/android-auto/8mvJEDnJUpU/pmejOMunAgAJ
terre08 said:
My unit came with a remote. I also find what I believe is a software bug, if you turn on the dimmer the maps will always be in night mode.
Click to expand...
Click to collapse
I found out it's by design by reading the user manual a bit better. The dimmer is connected to the headlights and when you turn on the lights it will go into night mode, unfortunately I use the lights 24/7 so I will install a toggle switch instead to turn on/off the daylight and the night mode. Pioneer has a a similar setting using the headlights but they also have a setting where you can set the time for night mode, hopefully Sony will have something similar in a future update.
Thanks for the replies!
I've worked out that the unit is detecting the handbrake as the video playback from an SD card is interrupted. I see the comment about the Sony not having built in GPS causing Android Auto to keep the 6 press limit, thats annoying, lets hope its fixed in an update. Surely it can use my phones GPS signal to work out when I'm stopped!
Terre08, I'll send you a PM regarding your remote...interesting!

car screen cut off

I have a moto x pure connected with chevy volt using android auto. It used to work perfect with the stock rom.
Recently I have installed the orionos custom rom, and the screen resolution in the car is totally wrong. I can only see the very top left portion of the screen, I think it is a screen resolution issue, but do not know how to solve it.
Any help is appreciated.
same issue
I have a brand new Skoda connected to an LG Optimus G updated to Android 6.0.1 and exactly the same issue. The screen is completeley screwed up and showing only the top left quarter of the screen way too large (huge fonts, etc.) Is there a way to fix this? Would even be good to know if this is a bug in the phone, in the car system or in the Android Auto app.
Anyone else facing this?
Is it possible you may have downloaded a 1024x600 rom instead of a 800x480?
I have a HTC 10, completely stock rom and a Pioneer head unit. Maps always worked perfectly in over a year with this phone and previous phone.
About a week ago I started to have this same issue. Maps is totally useless since.
I will try and get a photo tomorrow and reply again with it.
Just to let you know not only one.
I could fix my display issue by upgrading my phone to an Android 7 custom ROM.
duflez said:
I have a HTC 10, completely stock rom and a Pioneer head unit. Maps always worked perfectly in over a year with this phone and previous phone.
About a week ago I started to have this same issue. Maps is totally useless since.
I will try and get a photo tomorrow and reply again with it.
Just to let you know not only one.
Click to expand...
Click to collapse
Same thing here, HTC10, but with stock+magisk/xposed, same issue in Maps - until I saw this I thought that is because of one of xposed module. I cleanup the storage data several times, reinstalled aa also, disabled magisk/xposed, played with app settings xposed module in order to try to change the screen dp. Could not find the issue.
Interesting part is that on the same car but with different phone (moto x 2nd, xposed, same aa version, same google maps version) the Maps is displayed properly.
I have the same problem after updating my rom to a 1024x600. My unit was 800x480 and thats why the screen is cut off. What can i do?
In my case issue was related to Boost+ app "optimization", see this post https://forum.xda-developers.com/htc-10/help/android-auto-google-maps-issue-t3533388

8inch vw RK3188 wheelkey issue

Hi there, i am not too sure if i need to start a new topic, but i guess this is the best way to get your expertise on my issue.
I am driving a seat leon 1p (2008) which had the RNS510 (seat media system so whitout the sd card slot) built in. Sadly the display died (full white) and i had to search for something else.
I bought me a RK3188 device (it says ERISIN in the advert, i cannot find that name on the box or device itself) with a load of nice features. Most of them are working like they should, others have some hickups and 1 is really bothering me. I have made a youtube video and the seller says they don't see whats wrong. I bought it trough eunavi on aliexpress.
Here my explanation, the leon is fitted with a large dot matrix mfd screen in the dashboard (boardcomputer) (there are versions with a smaller display)
the big display is served with the windscreen wiper handle, which has 3 buttons, up, down, and ok/reset.
When i want to reset my computer (trip, avg fuel etc.) i need to press the reset button about 3 seconds. the radio then decides to shutdown... once i release the reset button, the radio decides it doesnt want to shutdown.
Quite weird in my opinion. So i tried programming the wheelkey settings, according to the manual. first i go into wheelkey settings, then i press clear / reset.. then i need to press any wheelkey (so allso the volume up / down, next, previous etc etc.) the radio does respond to that, but not with the wheelkey settings programme. I'll try to add the youtube link here as well.
next to this, some weird things happen.
1.The display is way too bright, so i asked the seller what to do, they told me they will send a new display which i should fit myself. In my opinion not the best solution from a shop but i understand their marigins aren't enormous and they try to fix it cheap. the display hasn't arrived yet so i can't say if the new display gives the solution for me.
2. when i have the tuner on, with af-rds function, it seems to scan to any rds station once the signal gets weak. Maybe i'm spoiled, but i think AF needs to search for the station with the same ID as the one i was tuned in to.
3. the dab+ dongle and window antenna give poor reception now. this is presumeably caused by the way i fitted the aerial, on top of the ventilation shafts behind the dashboard. I want to move the antenna to behind the rear view mirror (horizontally) which will hopefully give good reception. (does anyone know if horizontal positioning of the antenna is okay for dab+ ?)
<- the issue with the MFD input
<- the whiteness of the display (cannot be edited with standard settings) it was quite cold when i made this video, it seems it is a little better now or i am getting used to it
so quite a long story and i have my fingers crossed on your response !
maybe good to let you know:
MCU version
MTCD_LM_V1.90_1
sep 23 2016 09:37:48
Android-sersion
5.1.1
Kernel-version
3.0.101+
[email protected] #90
Fri Sep 9 16:24:49 CST 2016
Build-number
rk3188-userdebug 23092016.13:30:50

Android unit slow reverse camera activation (unit goes into shutdown instead of sleep

hi,
apologies if this has been discussed already but after running a search didnt find my answer.
Problem. Chinese replacement radio unit from Bosstar running Androind 8.1. Initial boot time is 35 sec. at which time the reverse becomes available. There is a menu option to put the unit to sleep for NONE/10MIN/30MIN/1HR after which time the unit goes into shutdown. Once shut down it takes 35 sec for reverse camera.
When in sleep the reverse camera is up and running within 5 sec.
Question.
How can I extend the delay from 1 hr to say 18 hrs. that would cover majority of situations where i want the camera to be active straight away ?
Is there a way to prioritise the camera over radio which is up and running in 10 sec regardless of the state f the unit (sleep/shutdown)
The supplier is beging unhelpful saying the re-programming is not possible.
Love the rest of the unit with the exception of the phone dialler and the bluetooth streaming app (same app as dialler). generic and feature poor. No idea how to replace it.

Categories

Resources