Related
Please I need help and I did a lot of search and got no answer, it has been 2 weeks now and my tilt is not working ok here is the storie I installed a new rom and everything is fine but once it reboot it stop on the BDIII screen for 5-10 second and it will automatic restart and keep doing the same. Please I really need some one to help me out. Thanks
have you tried to re install the rom by holding the camera button, the power button, and pushing the stylus into the hole at the bottom of the phone at the same time and once the 3 colored screen comes up u start the rom flashing program (cant remember what its called off hand just know it has RUU in it). that's what i do when i make a rom that messes up and gets stuck after the red letters appear.
May be a battery/Voltage Issue
I have a Tilt, and after open back door and remove battery while phone was working (O.K. I know now, It´s was a great mistake), furthermore, my phone do same things. Initially, It was able of a complete booting with native battery, later, only with charger (Altought, later the phone resset again and again and never complete boot.) . After some cycles, phone was unable for complete boot. Now the great thing: I have an extra battery,2200mAh. and see that Installing it on phone it was able again of complete a booting....and restart cycle again. After a search here, I decide to do a Hard reset in the few seconds that the Tilt was completely booted and working... And.... Voilá.... the phone is working now as I like to do.
I think that, If you make the Hard reset since Initially rebooting cycles, when phone is able yet to complete boot, It too must be a good Idea.
There are several threads about it:
http://forum.xda-developers.com/showthread.php?t=307378
http://forum.xda-developers.com/showthread.php?t=314588
Yo tengo un Tilt, y me paso lo mismo. Se me ocurrio quitarle la bateria sin apagarlo primero, y empezo con cilos de re-booteo. Inicialmente completaba el arranque, pero despues de varios ciclos ya no lo completo. Lo conecte al eliminador, y ví que nuevamente completaba el arranque (boot), pero despues de varios ciclos solo ponia la pantalla de HTC y se reseteaba. Tengo una batería extra de 2200mAh, se la instale, y observe que nuevamente completaba el arranque antes de volver a reiniciarse una y otra vez. Asi que segun lei en otro post de xda-developers, hize un Hard reset en los pocos segundos que duraba el arranqueucompleto y...Listo, quedo funcionando de nuevo. Creo que si hubiera hecho un Hard reset desde el principio,en vez de quedarme viendo como se reiniciaba en ciclos cada vez mas breves, me habria evitado dolores de cabeza.
Hay varias discusiones con este tema.
http://forum.xda-developers.com/showthread.php?t=307378
http://forum.xda-developers.com/showthread.php?t=314588
Humidity
I had a similar problem a while back. The phone rebooted and I had random key presses. The problem persisted over several roms. I live in hot and humid Dhaka at the moment. After a while I discovered the problem was humidity. Keeping the phone out of my pocket when I was outside, and drying it by the AC solved the problem.
akawings said:
have you tried to re install the rom by holding the camera button, the power button, and pushing the stylus into the hole at the bottom of the phone at the same time and once the 3 colored screen comes up u start the rom flashing program (cant remember what its called off hand just know it has RUU in it). that's what i do when i make a rom that messes up and gets stuck after the red letters appear.
Click to expand...
Click to collapse
I have tried to install the rom again but no luck got the same issue.
maya_jorge said:
I have a Tilt, and after open back door and remove battery while phone was working (O.K. I know now, It´s was a great mistake), furthermore, my phone do same things. Initially, It was able of a complete booting with native battery, later, only with charger (Altought, later the phone resset again and again and never complete boot.) . After some cycles, phone was unable for complete boot. Now the great thing: I have an extra battery,2200mAh. and see that Installing it on phone it was able again of complete a booting....and restart cycle again. After a search here, I decide to do a Hard reset in the few seconds that the Tilt was completely booted and working... And.... Voilá.... the phone is working now as I like to do.
I think that, If you make the Hard reset since Initially rebooting cycles, when phone is able yet to complete boot, It too must be a good Idea.
There are several threads about it:
http://forum.xda-developers.com/showthread.php?t=307378
http://forum.xda-developers.com/showthread.php?t=314588
Yo tengo un Tilt, y me paso lo mismo. Se me ocurrio quitarle la bateria sin apagarlo primero, y empezo con cilos de re-booteo. Inicialmente completaba el arranque, pero despues de varios ciclos ya no lo completo. Lo conecte al eliminador, y ví que nuevamente completaba el arranque (boot), pero despues de varios ciclos solo ponia la pantalla de HTC y se reseteaba. Tengo una batería extra de 2200mAh, se la instale, y observe que nuevamente completaba el arranque antes de volver a reiniciarse una y otra vez. Asi que segun lei en otro post de xda-developers, hize un Hard reset en los pocos segundos que duraba el arranqueucompleto y...Listo, quedo funcionando de nuevo. Creo que si hubiera hecho un Hard reset desde el principio,en vez de quedarme viendo como se reiniciaba en ciclos cada vez mas breves, me habria evitado dolores de cabeza.
Hay varias discusiones con este tema.
http://forum.xda-developers.com/showthread.php?t=307378
http://forum.xda-developers.com/showthread.php?t=314588
Click to expand...
Click to collapse
I tried but samething.
bandur said:
I had a similar problem a while back. The phone rebooted and I had random key presses. The problem persisted over several roms. I live in hot and humid Dhaka at the moment. After a while I discovered the problem was humidity. Keeping the phone out of my pocket when I was outside, and drying it by the AC solved the problem.
Click to expand...
Click to collapse
Thx but not working here.
Can any one answer my question.....
I'm with a problem that I consider serious xD
try to update my kernel to the version of voodoo, completed the process I restart the phone constantly and will not let me enter recovery mode ... I can only enter the download mode probe charge but again my rom (I use the 2.3.4) but still is constantly restarting and no longer do
someone tells me how I can revive my phone? : (
estoy con un problema que yo lo considero grave xD
trate de actualizar mi kernel a la version de voodoo, terminado el proceso el celular se me reinicia constantemente y no me deja entrar al modo recovery... solo puedo ingresar al modo download pero ya probe cargarle de nuevo mi rom (uso la 2.3.4) pero igual sigue reiniciandose constantemente y ya no se que hacer
alguien me dice como puedo revivir mi telefono?
there any way to install the recovery mode from the menu download?
hay alguna manera de instalar el recovery mode desde el menu download?
If you were on an AT&T gingerbread ROM, then i would suggest grabbing either boog's kernel or the corn kernel and flashing the kernel via Odin or heimdall. That will give you cwm recovery from download mode.
I have tried everything but still get to restarting the screen AT & T and I still can boot into recovery mode, I can only enter the download mode ...
He explained briefly that's what I did if you can tell me where the problem is: enter the page http://project-voodoo.org/download voodoo and download this file: Eclair: Galaxy S Captivate AT & T (SGH-i897) Voodoo lagfix-only 3.0 update.zip (updated 09/02/2010):
you need to rename it to update.zip, see Installation
after installing on my phone began to restart the phone constantly and after that I could not make it work
someone please help me because I lost my phone: (
ya he intentado de todo pero sigue reiniciandose al llegar a la pantalla de AT&T y sigo sin poder iniciar en el modo recovery, solo puedo ingresar al modo download...
Explico brevemente que fue lo que hice por si puedan decirme donde esta el problema: ingrese a la pagina de voodoo http://project-voodoo.org/download y descargue este archivo: Eclair: Galaxy S Captivate AT&T (SGH-I897) Voodoo lagfix-only 3.0 Update.zip (updated 2010-09-02):
you need to rename it to update.zip, see Installation
despues de instalar en mi telefono el telefono empezo a reiniciarse constantemente y luego de eso ya no pude hacerlo funcionar
alguien me puede ayudar por favor porque no quiero perder a mi telefono
reading in various parts of my encounter that perhaps the bootloop ... how I can solve a bootloop if I can not access the recovery menu? as I said earlier, only I can access the download menu
leyendo en varias partes encuentro que lo mio tal vez sea el bootloop... como puedo solucionar un bootloop si no puedo acceder al menu recovery? como dije al principio, solo en el menu download puedo acceder
You'll need to Use Odin to flash a compatible kernel. Odin is used with on a computer work your phone hooped up to it in download mode.
UPDATE: Now I got used to reinstall the ROM that used previously (2.3.4), I also install the CWM V4.0.1.5 but when I reboot system now goes back into recovery mode, what is the problem now?
ACTUALIZACION: ahora consegui reinstalar la ROM que solia usar anteriormente(2.3.4), tambien logre instalar el CWM V4.0.1.5 pero cuando le doy reboot system now vuelve a entrar en el modo recovery, cual seria el problema ahora?
Hello this is my first post and I'm desperedo! Today ICS install a ROM http://forum.xda-developers.com/showthread.php?t=1362092
I had the Factory ROM 2.2.1 and had no problems when installing the ICS, then I realized that HD games and thought I shut him a backup but this failed, I gave up and as I was in a ClockWordMod format (wipe) after the phone reboots, the phone is on the screen I have AT&T and I can not access the download mode, and only took 1 week for me to buy it from Amazon.com and I'm crying. Looking on Youtube I found a video of what is happening to me http://www.youtube.com/watch?v=betzMPoTD68
PS: My phone came with a factory default, the button off and on always gets stuck and just what I put the battery is turned on at once. Someone please help me to solve this Bootloop.
This text was translated with Google Translate
---------------------------
Hola este es mi primer post y ando desperedo!! Hoy instale una ROM ICS http://forum.xda-developers.com/showthread.php?t=1362092
Yo tenia la ROM de Fabrica 2.2.1 y no tenia problemas cuando instale la ICS, despues me di cuenta que los juegos HD se me cerraban y pense hacerle un Backup pero este fallaba, me di por vencido y como estaba en el ClockWordMod hice un formateo (wipe) despues reincie el telefono, el telefono se me queda en la pantalla de AT&T y no puedo acceder al modo descarga, y apenas llevo 1 semana de que me lo compre por Amazon.com y estoy llorando. Buscando en Youtube me encontré con un video de lo que me está pasando http://www.youtube.com/watch?v=betzMPoTD68
PD: Mi telefono vino con un defecto de fabrica, el boton de apagar y prender se queda siempre pegado y apenas a lo que le pongo la bateria este prende de una vez. Alguien que me ayude porfavor para solucionar este Bootloop.
Este texto fue traducido con el Traductor de google
ManuelZRO said:
Hello this is my first post and I'm desperedo! Today ICS install a ROM http://forum.xda-developers.com/showthread.php?t=1362092
I had the Factory ROM 2.2.1 and had no problems when installing the ICS, then I realized that HD games and thought I shut him a backup but this failed, I gave up and as I was in a ClockWordMod format (wipe) after the phone reboots, the phone is on the screen I have AT&T and I can not access the download mode, and only took 1 week for me to buy it from Amazon.com and I'm crying. Looking on Youtube I found a video of what is happening to me http://www.youtube.com/watch?v=betzMPoTD68
PS: My phone came with a factory default, the button off and on always gets stuck and just what I put the battery is turned on at once. Someone please help me to solve this Bootloop.
This text was translated with Google Translate
---------------------------
Hola este es mi primer post y ando desperedo!! Hoy instale una ROM ICS http://forum.xda-developers.com/showthread.php?t=1362092
Yo tenia la ROM de Fabrica 2.2.1 y no tenia problemas cuando instale la ICS, despues me di cuenta que los juegos HD se me cerraban y pense hacerle un Backup pero este fallaba, me di por vencido y como estaba en el ClockWordMod hice un formateo (wipe) despues reincie el telefono, el telefono se me queda en la pantalla de AT&T y no puedo acceder al modo descarga, y apenas llevo 1 semana de que me lo compre por Amazon.com y estoy llorando. Buscando en Youtube me encontré con un video de lo que me está pasando http://www.youtube.com/watch?v=betzMPoTD68
PD: Mi telefono vino con un defecto de fabrica, el boton de apagar y prender se queda siempre pegado y apenas a lo que le pongo la bateria este prende de una vez. Alguien que me ayude porfavor para solucionar este Bootloop.
Este texto fue traducido con el Traductor de google
Click to expand...
Click to collapse
Disconnect your phone from your computer if it's connected and take out the battery. Hold the volume up and down keys, connect your phone to your computer while doing this, and then insert your battery while still holding down volume up and down. This might get you into download mode.
help
1.Disconnect your phone from your computer if it's connected
2.take out the battery
3.Hold the volume up and down keys, connect your phone to your computer while doing this
4.then insert your battery while still holding down volume up and down. This might get you into download mode.
te estoy ttraduciendo lo que puso el miembro sthodupunuri en la descripcion
1.descocecta el telefono de la computadora (si se encuentra conectado)y quita la batteria.
2.presiona los botones del volume arriva-abajo al mismo tiempo(no los sueltes)
3.conecta el usb cable y insierta la bateria eso te pondra en download mode
mucha suerte si nesecitas mas ayuda reply a este mensage
chicanowpride said:
te estoy ttraduciendo lo que puso el miembro sthodupunuri en la descripcion
1.descocecta el telefono de la computadora (si se encuentra conectado)y quita la batteria.
2.presiona los botones del volume arriva-abajo al mismo tiempo(no los sueltes)
3.conecta el usb cable y insierta la bateria eso te pondra en download mode
mucha suerte si nesecitas mas ayuda reply a este mensage
Click to expand...
Click to collapse
Per forum rules please translate this to english and post in your original post alongside the spanish version.
Nothing happened, so no access to the download, it's the same as in the video where you try to access the recovery mode, but this one is like the circle loading and off the screen and turns on again. I'm thinking the USB JIG solution but I have the problem that the phone is turned on you just put the battery and I doubt that I may have the USB method JIG
This text was translated with GoogleTranslate
----------------------------------------------------------------------
No ha pasado nada, no accede al modo descarga, pasa lo mismo como en el video en donde se intenta acceder al modo recovery, pero este se queda como el circulo cargando y se apaga la pantalla y se prende otra vez. Ando pensando en la solucion del USB JIG pero tengo el problema de que el telefono se prende apenas le pongo la bateria y dudo que me sirva el metodo del USB JIG
ManuelZRO said:
Nothing happened, so no access to the download, it's the same as in the video where you try to access the recovery mode, but this one is like the circle loading and off the screen and turns on again. I'm thinking the USB JIG solution but I have the problem that the phone is turned on you just put the battery and I doubt that I may have the USB method JIG
This text was translated with GoogleTranslate
----------------------------------------------------------------------
No ha pasado nada, no accede al modo descarga, pasa lo mismo como en el video en donde se intenta acceder al modo recovery, pero este se queda como el circulo cargando y se apaga la pantalla y se prende otra vez. Ando pensando en la solucion del USB JIG pero tengo el problema de que el telefono se prende apenas le pongo la bateria y dudo que me sirva el metodo del USB JIG
Click to expand...
Click to collapse
Can you try getting into recovery mode? Take the battery out, hold down volume up and volume down buttons. Then put the battery in while still holding the buttons down. Keep holding the buttons until the phone boots into recovery. From there, install a gingerbread rom. An ICS rom will not install with froyo bootloaders.
http://forum.xda-developers.com/show....php?t=1530886
My phone is in a bootload yesterday and found a method, which is with the ADB and Android SDK, I followed a guide I found in Spanish in HTCMania and also a video on YouTube in English, here are the video: http://www.youtube.com/watch?v=oaNM-...layer_embedded
I followed all the steps but at the time to put "adb reboot recovery" tells me "device not found"
IMAGE:
http://img849.imageshack.us/img849/3182/dibujorhx.png
We thank some kind of help please, here is a video that i found in Youtube that shows exactly what is happening to me http://www.youtube.com/watch?v=betzMPoTD68
PD: My phone when you buy it, came with a manufacturing defect, the power button on / off is stuck inside and when the battery put the phone on immediately, as a result of this I can not use the USB method JIG.
This text was translated with GoogleTranslate
-----------------------------------------------------
No puedo entrar al modo recovery ni nada he intentado lo que han dicho y nada.
Investigando en internet consegui un metodo para iniciar el recovery con ADB. Segui los pasos de esta guia
Pero en el momento de poner adb reboot recovery, dice: device not found, intenté instalar los drivers USB otra vez pero no sucede nada no me reconoce el telefono. ¿No sera por la ROM ICS que no me quiere reconocer el telefono?[/QUOTE]
-----------------------------------------------------
No puedo entrar al modo recovery ni nada he intentado lo que han dicho y nada.
Investigando en internet consegui un metodo para iniciar el recovery con ADB. Segui los pasos de esta guia
Pero en el momento de poner adb reboot recovery, dice: device not found, intenté instalar los drivers USB otra vez pero no sucede nada no me reconoce el telefono. ¿No sera por la ROM ICS que no me quiere reconocer el telefono?
ManuelZRO said:
I send a private message with full message links do not let me post
I can not enter recovery mode and nothing I tried what you said and nothing.
Researching on the internet I got a method to start the recovery with ADB.
But just to put adb reboot recovery, says: device not found, I tried to install the USB drivers again but nothing happens I do not recognize the phone. Do not be the ICS ROM that I want to recognize the phone?
Click to expand...
Click to collapse
Did you try the 2 button combo? volume up + power button? also did you try changing your drivers from the captivate drivers to say the Galaxy Nexus drivers or the Google drivers? I know that fixed mine a while back
http://forum.xda-developers.com/showthread.php?t=1530886
If I tried to enter the recovery and the download and nothing, as my phone has the button On / Off stuck inside, so when I connect the battery the phone is turned away, just makes me fata press volume buttons and connect the battery to see if it comes to recovery, but not entered, the phone lights up the screen at & t and then goes black screen and returns to the screen at & t and so on, I'm trying with the SDK Manager but I have not solve the problem, I read this guide HTCMania forum http://www.htcmania.com/showthread.php?t=337069, this same guide is also on Youtube http://www.youtube.com/watch?v=betzMPoTD68&feature=related
The problem is I do not recognize the device
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
By manuelzro at 2012-03-05
Reinstall the drivers, install the drivers of Google and nothing happens, even when I connect the phone to USB and the PC does not recognize me the phone, I do not chip or a notice, nothing, something like "device is detected" or a signal, nothing, I'm really desperate any help would be appreciated.
This text was translated with Google Translate
---------------------------------------------------------
Si, intenté entrar al recovery y el Download y nada, como mi telefono tiene el boton On/Off pegado por dentro, y por eso cuando conecto la bateria el telefono se enciende inmediatamente, solo me hace fata presionar los botones de volume y conectar la bateria para ver si entra al recovery, pero no entra, el telefono enciende con la pantalla de at&t y luego se pone la pantalla en negro y vuelve a la pantalla de at&t y asi sucesivamente, ahora estoy intentando con el SDK Manager pero no he conseguido solucionar el problema, lei esta guia en el foro de HTCMania http://www.htcmania.com/showthread.php?t=337069, esta misma guia esta en Youtube tambien http://www.youtube.com/watch?v=betzMPoTD68&feature=related
El problema es que no me reconoce el dispositivo
By manuelzro at 2012-03-05
Reinstale los drivers, instale los drivers de Google y no sucede nada, e incluso cuando conecto el telfono al USB y la PC no me reconoce el telefono, no me salta ni una notificacion, nada, algo asi "Se ha detectado un dispositivo" ni una señal, nada, ando desesperado cualquier ayuda seria realmente apreciada
Have you tried a different cable? Or maybe even another computer? I've read quite a few posts here on XDA that the Samsung USB cable doesn't work with some computers or the computer itself is the problem..
[edit]
I noticed you're using
C:\android-sdk>
try using C:\Users\Yourcompuernamehere (the name you used for your computer ) >
Start -> All Programs -> Accessories -> Command Prompt
It might be trying to find your phone via an emulator or something?
For now I have not tried connecting the phone to another computer, another will try tomorrow to see if at least recognizes the phone.
did u try the USB jig to force it in to Dwd mode ? or there is another method
http://www.youtube.com/watch?v=Rdn5GoRjhn0
bbut i am not sure it will work in ur captivate. I had some problems , but another friend had no issues in this.....
I mean, my phone has the button On / Off stuck, so I can not use the USB method JIG because the battery just put the phone on immediately, the solution would be to repair the button On / Off in my area but I doubt they have support Android, much less this phone is not sold in my country, in addition to the telephony market in my country is invaded by Blackberry (4 of 5 people have a Blackberry). The USB JIG MercadoLibre.com sell it on but I need repair first button on / off
This text was translated with Google Translate
I just tried another USB cable but the PC does not recognize me the phone yet, I'm hoping that me will bring a laptop to see if it recognizes the phone.
The translations are considered google translator? No great confidence in this translator
As I posted in your other thread, the only thing I can suggest is trying the Nexus S drivers since your phone cannot be recognized.
I have the exact same Issue! My power button it's stuck so every time I put the battery the phone power on by itself... But I know the cause of my issue... I had a bootloop so on CWM I formated /boot later I discover that "/boot" is for bootloader and no for the ROM. So I'm stuck as you!
I don't think the correct drivers will work, because you need to be on download mode for that. I CAN'T get there. ANY HELP!?
BTW: I speak spanish PM if you found a solution.
Have you tried holding the vol up + vol down buttons while plugging in the phone? Or even volume down + power button(you say its stuck so no need to press it) while plugging in the phone?
cOld1 said:
Have you tried holding the vol up + vol down buttons while plugging in the phone? Or even volume down + power button(you say its stuck so no need to press it) while plugging in the phone?
Click to expand...
Click to collapse
Yes I tried that... But I get stuck either on ATT Screen or in the "loading battery charge logo" << just the circle not the battery logo itself, and if I pressed UP and DOWN it get stuck on a bootloop. ATT screen >> Black screen >> Att screen ... etc.
ADB or the jig method? One of those 2 has to work..
Hola.
Les comento mi problema en detalle.
*Ayer flashie como normalmente lo hacia desde el TWRP, la ultima actualización de CM11.0 de Novafusion (Maclaw). Cuando lo prendí, vi que no funcionaba las aplicaciones de google (Play store, agenda, no sincronizaba con la cuenta de google, etc)
* Entonces, no se me ocurrió mejor idea que volver a un backup que tenia desde mayo, de CM11.0.
Antes de que termine de flashear esta ultima, se pone la pantalla en negro y en letras rojas aparece "RST_STAT 0x000000000"
Seguia prendiendo normalmente, solo que antes del boot logo, se ponia una pantalla por 5 segundos que era blanca con lineas horizontales negras.
*Bueno, despues de esto lo que hice fue flashear con una version anterior de maclaw de hace unos dias (CM11 tambien), pero lo que me ocurre es que me aparece como si tengo señal (pero si bajo la barra de estado me aparece como que no tengo señal y dice solo llamadas de emergencia el icono de la señal). Lo irónico es que si tengo 3G, pero no puedo realizar ni recibir llamadas, ni enviar ni recibir mensajes. Cuando quiero hacer una llamada me aparece "LA RED MOVIL NO ESTA DISPONIBLE"
*Restaure la carpeta EFS, pero sigue sin funcionar..
La verdad es que estoy desesperado, no se que hacer con el celular. Anda todo menos, la función principal de un celular, (llamadas y mensajes.)
Espero que alguien me pueda ayudar por favor.
Desde ya, muchas gracias.
Adrian.
PD: Tengo movistar y soy de argentina. Y el chip en otro celular anda. No es problema del chip ni de la oepradora,
TRADUCIDO CON GOOGLE
Hello .
I commented my problem in detail.
* Yesterday as you normally flashie to TWRP since the last update of Novafusion CM11.0 ( Maclaw ) . When I turned , I saw that did not work google apps (Play store , calendar, not synchronized to google account , etc )
* So, it never occurred to me better idea to go back to a backup I had from May to CM11.0 .
Before the end of this last flash , the screen turns black and red lettering is " RST_STAT 0x000000000 "
She kept turning on normally , just before the boot logo , a screen for 5 seconds that was white with black horizontal lines it was coming down .
* Well, after that I did was flash an earlier version of maclaw a few days ago ( CM11 too) , but what strikes me is that I appear as if I have signal ( but under the status bar appears to me as I have no signal and says emergency calls only the signal icon ) . The irony is that if I have 3G, but I can not make or receive calls or send or receive messages . When I want to make a call appear to me " THE MOBILE NETWORK NOT AVAILABLE "
* Restore the EFS folder but still not working ..
The truth is that I am desperate not to do with the phone. Anda anything but , the main function of a cell phone ( calls and messages. )
I hope someone can help me please .
From already , thank you very much .
Adrian .
PD : I 'm from Argentina and Movistar . And the chip goes in another cell . No problem chip or Attendant
If you have an I8190 go to this thread. If you have L or N variant, search in the same thread for pit file for L or N, I think someone posted for L & N too. Before doing something (bad, brick, whatever), read the thread very carefully. Good luck.
P.S. for N here, for L here.
thanks for your answer.
But the link of the file for I8190L doesnt work :/
you know where I can get that file?
------------
Edit:
I finally found the file.
I flash ir, but the same thing keeps happening. I have 3g, but i cant do any calls o send message.
Any help, please ?
may be that the cell is in negative band after flashing ?
call center movistar and they told me it was negative band for another company . What I have to do ?
because before flashing, the cellphone have signal, and i had 3g, i could make calls, and messages
Don't know mate! Try flashing a stock rom instead or try other basebands here.
No puedo recibir llamadas ni mensajes. Solo me anda el 3G.
Me di cuenta que después de flashear, no tengo los archivos .nv_data.bak y .nv_data.bak.md5
Y no tengo un backup de estos.
Y si borro la carpeta EFS, no aparecen devuelta…
Alguna solución por favor ?
————————
I can not receive calls or messages. Just go my 3G.
I realized that after flashing , I dont have the files .nv_data.bak and .nv_data.bak.md5 in my phone
And I dont have a backup of these .
And if I delete the EFS folder, do not appear these files back..
Any solution please?
I do not know if someone can help me on my razer phone 2 I wanted to change the rom the problem was not that the process was successful the problem is that I wanted to put magisk but apparently I did the process wrong I did not follow the instructions and install a version that al It seems it was not shareable with my phone the problem is that this caused the phone to erase all the rom the serial all the only thing that remained was the twrp but it does not let me install or do anything whenever you try to do a process that fails not even With the pc in download or bootloader mode, I do not know if someone has any solution to be able to recover that phone (I already contacted razer and their solution was to send them the phone and pay to have it repaired, I know that it may take time and I have no budget to pay what they are going to charge)
Could you paste the error message or even a picture of it?
Might be useful to see the error.
Los errores son algo así, no encuentra los datos ni ningún tipo de partición como se ve en las imágenes y luego todos los errores que da al querer restaurar el celular o instalar una rom y en el bootloader lo único que Sucede es que si reconoce la computadora pero al realizar las acciones o comandos como querer flashear el recovery o el sistema se queda atascado y no ejecuta nada
Reformat all the partitions and then install your stock ROM zip.
The Zip can be obtained from your manufacturers website.
Kenora_I said:
Vuelva a formatear todas las particiones y luego instale su archivo zip ROM.
El Zip se puede obtener en el sitio web de su fabricante.
Click to expand...
Click to collapse
I already did it but it does not leave exactly the same message in echo I tried to install the manufacturer's rm zip in that chapter and right after I wanted to format but nothing works it always goes without success
Ya lo hice pero no deja exactamente el mismo mensaje en echo Intenté instalar el zip del rm del fabricante en ese capítulo y justo después quise formatear pero nada funciona siempre sale sin éxito
do you still hve this phone?
itz_jordann said:
do you still hve this phone?
Click to expand...
Click to collapse
Yes i have