{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
For those about to flash..... I salute you!
With AICP 15 fueled by Android Q.
NOTE: TESTBUILD. SELINUX DISABLED.
Since I build this ROM, I might as well upload it here for other to enjoy.
You should get to know how to flash before you download this (and potentially softbrick your phone). I may create detailed instructions later, but for now just search xda.
The basics are:
ZF6 has 2 slots (A/B) for ROM, Boot, Vendor and many other partitions. To start with we want the same version in both slots. We get that by flashing the full stock ROM two times. Remember: every time you flash a ROM, it will automagically change to the other slot. The recovery(TWRP) will swap slots when rebooting to recovery (but only after flashing a ROM).
Do not change slots yourself, let the installer manage!
Do not wipe system partition or other partitions unless it is specified!
Installing AICP Q:
Initially, you must have Android Q installed and working in both Slot A and B. Verify that it works, then use mauronofrios twrp to flash AICP. In short:
- Get Android Q running on both slots
- Remove all fingerprints from current ROM.
- Remove all locks on lockscreen.
- Boot TWRP 3.3.1-24 Q Unofficial by mauronofrio from your PC (or boot directly to twrp if already installed).
- Flash AICP Q
- Flash TWRP 3.3.1-24 Unofficial Installer by mauronofrio
- reboot to TWRP (this will activate the other slot, where AICP just got installed)
- Optionally Flash gapps
- Optionally Flash magisk if you want root
- Wipe data
- ReBoot to system
Don't panic if things go wrong. I have never seen a device being hard bricked due to wrong flashing.
EXPECT soft bricks if this is your first flash! A/B devices are tricky.
If you are uncertain of anything, make sure you have access to help (I will not be around much).
SOURCE with everything you need to build yourself.
The kernel used is from the LineageOS project. It can be found by following the manifest above or direcly HERE.
DOWNLOAD for Pie
If ^^ is too slow, try here.
HAVE FUN
The official introduction:
AICP
Android Ice Cold Project
AICP is known by everyone as the "Ice Cold Project" that started on a Desire HD years ago (2012) and since then has evolved into a mature ROM with the BEST community that you can find!!!
Until Android Lollipop, the ROM has always been based on AOKP. Unfortunately, since AOKP stopped development (but made a comeback later), we changed our base to CM.
With the re-brand of CM to LineageOS (LOS) we became LineageOS based with some tweaks from AOSP, for Android Pie we based on the "Ground Zero Open Source Project" (GZOSP), and now for Android 10 we are fully based on AOSP
Code:
#include <std_disclaimer.h>
/*
* Your warranty is now void.
*
* We are not responsible for bricked devices, dead SD cards,
* thermonuclear war or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications and if
* you point the finger at us for messing up your device, we will laugh at you. Hard & a lot.
*
*/
Feature list (rough overview)
In the beginning we would like to thank:
GZOSP team
LineageOS & CM (R.I.P.) team
@maxwen and the rest of the OmniRom team
DU team
SlimRoms team
Resurrection Remix team
Community
...
@LorD ClockaN
@zipsnet
@eyosen
@semdoc
@SpiritCroc
@wartomato
@eboye
plus the rest of the crazy bunch that we call "team"
...
We are paying for servers that build nightlies/weeklies and everything that comes with it, so EVERY DONATION will really be appreciated and be used to cover those expenses.
Thank you!!
Latest Stable Release Version 14.0
Download link: https://dwnld.aicp-rom.com/
Please note that official builds will be deleted from our servers every month due to maintenance services.
We advise everyone to keep at least the latest or best working build on their device as a backup.
Maybe copy it to a cloud service or USB too.
Full Changelog link: https://dwnld.aicp-rom.com/
(Just click the changelog button next to the download link in the list of builds available for your device)
Google Apps:
(link the best one for your device, there are several variants out there right now, nano/micro GApps from opengapps.org is almost always a good choice though)
You tell...
FAQ:
Before using the ROM:
Q. Can I have an ETA for the next build?
A. Yes, just look here to see what day your device is built on.
Q. Does this ROM support custom kernels officially?
A. No. You can still use them, but discussion should go in the thread of the respective kernel. We don't offer support for bugs you might encounter while using them!
Q. Why doesn't this ROM support Xposed?
A. Xposed is a hack that is geared towards AOSP. Custom ROMs modify the framework a lot, so Xposed can cause a ton of issues on custom ROMs. Now it might work for you, however it is not to be discussed in this thread, and you should refrain from posting bug reports.
Q. Alright, but I still want to flash Xposed, so which version do I need to install?
A. Xposed is not yet released for android 10.
Flashing the ROM:
Q. What do I need to know before flashing?
A. Check the flashing instructions...
Q. Can the builds be dirty flashed over each other?
A. Yes, however make a nandroid backup first as there is a chance of getting a bootloop or encountering bugs. Also bugs may only be reported on a clean flash.
Q. How do I 'dirty flash' builds?
A. Wipe the System, Cache and ART/Dalvik cache. Flash the ROM, GApps (only needed if you wipe the system), your preferred root solution and reboot. Or just use the OTA app to preform that task for you.
Q. How do I flash kernel builds?
A1. If it's a .img file, boot into TWRP and go to the install page in TWRP, in the bottom right corner select "install image", select the desired kernel, then select "boot" as the destination, then swipe to flash, then go back to the install screen and install your root method again, if you don't want to loose root and reboot.
A2. If it's a flashable ZIP, you can flash it together with a ROM update or separately. Go to the install page in TWRP, choose the kernel zip (or add it to the flash queue right after the ROM zip). Then add your root method to the queue if you don't want to loose root. Now swipe to flash and reboot afterwards.
Using the ROM:
Q. I installed a bad theme and now I'm getting a bootloop, how do I fix it?
A. In TWRP, flash the substratum rescue zip that's in the substratum folder on the internal storage.
Q. I'm having issues with WhatsApp, how do I fix it?
A. Read this
Q. Do I need to provide a logcat if I'm reporting a bug?
A. If you want it to be fixed faster (or at all) then yes, you should definitely provide a logcat. (Note: Please just link the logcat from your GDrive, Dropbox, etc. and do not post the content here. Thanks.)
Q. How do I get a logcat, what type should I get and more questions that can conveniently be answered by my pre-determined answer?
A1. Read this thoroughly. Also, here's a good app for getting logs: https://play.google.com/store/apps/details?id=com.tortel.syslog (Root needed).
A2. If you are already rooted, you can use the built-in feature to make a logcat and provide that. Just look into the others section in the AICP Extras main page.
The ROM should contain everything you need to enjoy Android 10. You don't need to install any Add-ons, simply download the latest ROM and GApps, then follow the flashing instructions and go!
If you want the device to run the ROM "rooted", you can flash a root solution of your choice after the ROM Zipfile.
It is STRONGLY recommended to fully wipe your device before flashing and please avoid restoring system apps and system data with Titanium Backup (or with any backup/restore app) as this can cause stability issues that are very hard to debug, restoring regular apps is fine though.
If you believe you know what you're doing - then fine, go ahead, but please don't complain if you experience any strange behavior.
How to flash for the first time:
(Again: Don't do it if you don't know!)
1. Download the ROM and GApps and transfer them to your device.
2. Boot to recovery (TWRP recommended).
3. Wipe the System, Cache, and Data (you might need to format the data partition!).
4. Flash the ROM Zipfile.
5. Flash the GApps (optional, needed for e.g. Google Playstore to work).
6. Reboot and set up your device, enable developer settings and in them OEM unlock/Advanced reboot/USB tethering.
7. Reboot back into TWRP recovery.
8. Flash the root solution of your choice (optional).
9. Reboot your device.
The procedure may vary from device to device and is a bit different on system updates!
The ROM has GApps persistence in between dirty flashes, so you only have to flash them once! This might differ on AvB Devices.
Currently supported Root Solution:
Magisk stable
Magisk versions >= 20.1 don't usually need to be flashed on every dirty flash.
Depending on the device, you may need to flash it every time, unless your maintainer says otherwise, you should be fine.
PREREQUISITE FOR OTA ("Over-The-Air" Updates):
TWRP recovery is needed to be able to flash using the built-in OTA app.
Please make sure that you are on the latest TWRP recovery, keep in mind that this could also be an unofficial version!
On encrypted devices you will have to enter your PIN/password in TWRP before the process starts.
If you want to contribute to AICP, or want see what is being worked on/merged, feel free to visit our Gerrit code review system. (Link is at the bottom!!!)
Kernel source:
Put the Github link to your kernel HERE (mandatory), not posting the kernel source violates the GPL, and also violates the rules on XDA ...
Device tree source:
Put the Github link to your device tree HERE.
Vendor source:
Put the Github link to your used vendor HERE.
ROM & Additional links:
AICP's Homepage
AICP Gerrit Code Review
AICP sources on Github
AICP Download page for official builds and media content
AICP Discord Community
AICP Telegram channel for server notifications on official builds
Contributors:
(mention all the devs who have contributed to your device tree, kernel, vendor, etc,
only mention the main ones though, probably the top four or so, otherwise this list will be a mile long xD)
The following information is ONLY needed if you are not opening up a devdb thread on XDA!
ROM OS Version: 10.x
Kernel: Linux x.z.y (for example: 3.18.y)
Version Information:
Status: WEEKLY
Release Date: mm-dd-yyyy
You want to see a "normal" night at the "DEV office", click here!!
Hi
thank you VM @teemo for your work. AICP best rom i ever had. i hope i have time to flash it on my 6z as soon™ as possible
any issues you know yet? and how about re-flashing TWRP each time after flashing rom?
Greetings
135Shadowsoul
PS: First
135Shadowsoul said:
Hi
thank you VM @teemo for your work. AICP best rom i ever had. i hope i have time to flash it on my 6z as soon™ as possible
any issues you know yet? and how about re-flashing TWRP each time after flashing rom?
Greetings
135Shadowsoul
PS: First
Click to expand...
Click to collapse
Safety Net need help from Magisk or similar. Will try to fix for next build.
I would love to have Quick Settings to dismiss when using the Camera Tile with gCam.
Asus camera gets slow in pro mode with slow shutter speeds.
Other than that, I don't know what to fix. You tell me :laugh:.
EDIT1: Oh yeah, the Google key need to be reassigned to something more useful...
EDIT2: Not an issue but yes, flash TWRP after the ROM.
teemo said:
Safety Net need help from Magisk or similar. Will try to fix for next build.
I would love to have Quick Settings to dismiss when using the Camera Tile with gCam.
Asus camera gets slow in pro mode with slow shutter speeds.
Other than that, I don't know what to fix. You tell me :laugh:.
EDIT1: Oh yeah, the Google key need to be reassigned to something more useful...
EDIT2: Not an issue but yes, flash TWRP after the ROM.
Click to expand...
Click to collapse
Thank you for this Rom. This seems to be the best Rom for this Device after the first Day of using it.
One little Thing: I am using two Simcards, but in the Statusbar I can see only Simcard 1 and also there is no LTE and Volte Sign.
teemo said:
Safety Net need help from Magisk or similar. Will try to fix for next build.
I would love to have Quick Settings to dismiss when using the Camera Tile with gCam.
Asus camera gets slow in pro mode with slow shutter speeds.
Other than that, I don't know what to fix. You tell me :laugh:.
EDIT1: Oh yeah, the Google key need to be reassigned to something more useful...
EDIT2: Not an issue but yes, flash TWRP after the ROM.
Click to expand...
Click to collapse
Thanks for reply m8,
about EDIT1: is it possible to reassign the key? like on stock rom? or do we need any special app/magisk module/whatever?
is asus camera built in? and any idea how to solve the camera thing you mentioned?
whats the stuff about safetynet? any problem with magisk and hide props conf module?
nnamless said:
Thank you for this Rom. This seems to be the best Rom for this Device after the first Day of using it.
One little Thing: I am using two Simcards, but in the Statusbar I can see only Simcard 1 and also there is no LTE and Volte Sign.
Click to expand...
Click to collapse
I've set mine to show 4G in stead. It works, but only if I'm not on WiFi.
SIM cards are both showing for me, but I have seen some strange things like showing the wrong card. I am currently only using SIM, the other one disabled.
135Shadowsoul said:
Thanks for reply m8,
about EDIT1: is it possible to reassign the key? like on stock rom? or do we need any special app/magisk module/whatever?
is asus camera built in? and any idea how to solve the camera thing you mentioned?
whats the stuff about safetynet? any problem with magisk and hide props conf module?
Click to expand...
Click to collapse
Yes it's possible, micky387 is already doing it for in OmniRom on Q if I'm not wrong.
Asus camera and gallery built in. If I knew how to fix the pro camera I had done it already.
I don't know if this latest build has SN working out of the box, as it just got feb security update. But Safety net is fine with Magisk props module.
I will probably be super slow to fix stuff, but any help is welcomed
Will update OP with links to the source, which I forgot.
IDK if I'm missing something, but when I click the link to download, I'm told access is denied. What's up?
Sraichvold said:
IDK if I'm missing something, but when I click the link to download, I'm told access is denied. What's up?
Click to expand...
Click to collapse
No, I added the wrong dl address, sorry. You can try again now. If still not working, just search for user teemo, then it's easy to find.
Sweeeet. Thank you kindly!
Quote:
Originally Posted by nnamless
Thank you for this Rom. This seems to be the best Rom for this Device after the first Day of using it.
One little Thing: I am using two Simcards, but in the Statusbar I can see only Simcard 1 and also there is no LTE and Volte Sign.
teemo said:
I've set mine to show 4G in stead. It works, but only if I'm not on WiFi.
SIM cards are both showing for me, but I have seen some strange things like showing the wrong card. I am currently only using SIM, the other one disabled.
It works if i install it over the latest LOS 16.0 instead of Stock Pie Rom. Use it now as daily Driver, very good! Thank You
Click to expand...
Click to collapse
nnamless said:
Quote:
Originally Posted by nnamless
It works if i install it over the latest LOS 16.0 instead of Stock Pie Rom. Use it now as daily Driver, very good! Thank You
Click to expand...
Click to collapse
That's good info. Thanks!
Q update in OP.
Related
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
AICP
Android Ice Cold Project
for Xperia Z3 Tablet Compact (scorpion/scorpion_windy) Unofficial
AICP is known by everyone as the "Ice Cold Project" that started on a Desire HD years ago (2012) and since then evolved into a mature ROM with the BEST community you can find!!!
Until Lollipop, the Rom has always been based on AOKP. Unfortunately, since AOKP stopped development (but made a comeback later), we changed our base to CM when it comes to hardware, drivers and some features.
With the re-brand of CM to LineageOS (LOS) we are now actually LOS based with some tweaks from AOSP.
If there are any bugs, either we will sort them out or the LOS team will if it concerns their code base. This rom isn't LOS supported, so no need to report errors/bugs to them!!
Code:
#include <std_disclaimer.h>
/*
* Your warranty is now void.
*
* We are not responsible for bricked devices, dead SD cards,
* thermonuclear war or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at us for messing up your device, we will laugh at you. Hard & a lot.
*
*/
Feature list (rough Overview)
In the beginning we would like to thank:
LineageOS & CM (R.I.P.) team
@Maxwen and the rest of the OmniRom team
DU team
SlimRoms team
Resurrection Remix team
Community
...
@LorD ClockaN
@zipsnet
@eyosen
@semdoc
@Drgravy
@Hashbang173
@SpiritCroc
@wartomato
@eboye
plus the rest of the crazy bunch that we call "team"
...
We are paying for servers that build nightlies/weeklies and everything that comes with it, so EVERY DONATION will really be appreciated and be used to cover those expenses.
Thank you!!
Donate to maintener
Donate to AICP team
Latest Stable Release Version 13.1
TWRP for scorpion/scorpion_windy
aicp_scorpion_o-13.1-UNOFFICIAL-20180708
aicp_scorpion_windy_o-13.1-UNOFFICIAL-20180708
See Settings -> AICP Extras -> Changelog in your tablet.
Camera Recording
Crypting Storage
FAQ:
Before using the ROM:
Q. Why doesn't this ROM support Xposed?
A. Xposed is a hack that is geared towards AOSP, custom ROM's modify the framework a lot, so Xposed can cause a ton of issues on custom ROM's. Now it might work for you, however it is not to be discussed in this thread, and you should refrain from posting bug reports.
Q. Alright, but I still want to flash Xposed, so which version do I need to install?
A. Xposed is not yet available for Oreo.
Flashing the ROM:
Q. What do I need to know before flashing?
A. Check the install instructions in the first post...
Q. Can the builds be dirty flashed over each other?
A. Yes, however make a nandroid first as there is a chance of getting a bootloop or encountering bugs. Also bugs may only be reported on a clean flash.
Q. How do I dirty flash builds?
A. Wipe the System, Cache and ART/Dalvik cache. Flash the ROM, GApps (only needed if you wipe the system), your preferred root solution and reboot. Or you might just use the OTA app to preform that task for you.
Q. How do I flash kernel builds?
A1. If it's a .img file, boot into TWRP and go to the install page in TWRP, in the bottom right corner select "install image", select the desired kernel, then select "boot", then swipe to flash, then go back to the install screen and install your root method again, if you don't want to loose root and reboot.
A2. If it's a flashable ZIP, you can flash it together with a ROM update or separately. Go to the install page in TWRP, choose the kernel zip (or add it to the flash queue right after the ROM zip). Then add your root method to the queue if you don't want to loose root. Now swipe to flash, and then reboot.
Using the ROM:
Q. How do I enable software buttons?
A. Until the navbar enabler is added, add the line qemu.hw.mainkeys=0 to the build.prop and then reboot, set it to 1 to disable it if you want. You can use an App like Kernel Audiutor for that.
Q. I installed a bad theme and now I'm getting a bootloop, how do I fix it?
A. In TWRP, flash the substratum rescue zip that's in the substratum folder on the internal storage.
Q. I keep losing root with Magisk, how do I fix it?
A. Check this out. If that doesn't work for you, ask for help in this thread, read or ask in the Magisk thread on XDA or just re-flash Magisk!
Q. I'm having issues with WhatsApp, how do I fix it?
A. Read this
Q. Do I need to provide a logcat if I'm reporting a bug?
A. If you want it to be fixed faster (or at all) then yes, you should definitely provide a logcat. (Note: Please just link the logcat from your GDrive, Dropbox, etc. and do not post the content here. Thanks.
Q. How do I get a logcat, what type should I get and more questions that can conveniently be answered by my pre-determined answer?
A1. Read this thoroughly. Also, here's a good app for getting logs: https://play.google.com/store/apps/details?id=com.tortel.syslog (Root needed).
A2. If you are already rooted, you can use the built-in feature to make a logcat and provide that. Just look into the root section in the AICP Extras menu.
The ROM should contain everything you need to enjoy Android Oreo. You don't need to install any Add-on's, simply download the latest ROM, GApps, flash it and go!
If you want the device to run the ROM "rooted", you can flash a root solution of your choice after the ROM Zipfile.
It is STRONGLY recommended to fully wipe your device before flashing and please avoid restoring system apps and system data with Titanium Backup as this can cause stability issues that are very hard to debug.
If you believe you know what you're doing - then fine, go ahead, but please don't complain if you experience any strange behavior.
How to flash:
(Again: Don't do it if you don't know it!)
0. Upgarade to latest bootloader
1. Download the ROM and GApps and transfer them to your device internal storage.
2. Boot to recovery (TWRP recommended).
3. Wipe System, Cache, Data and ART/Dalvik cache.
4. Flash ROM Zipfile.
5. Flash/Install GApps (optional, needed for e.g. Google Playstore to work).
6. Flash/Install the root solution of your choice (optional).
7. Reboot your device.
The ROM has GApps persistence in between dirty flashes, so you only have to flash them once!
The root solution should be flashed together with every OTA update (= ROM Update) as long as the instructions of your
root solution do not state something else (="persistence on dirty flashing") !
Currently Supported Root Solutions:
Magisk v16.0
KERNEL:
The kernel in this ROM follows LOS source with custom additions.
PREREQUISITE FOR OTA:
To be able to flash using the buildin OTA app, TWRP recovery is needed.
You can still use the LOS recovery and OTA app, but you will need to download the zip file and flash it manually from within your recovery. The Zipfile gets saved in the "aicp_ota" folder on your internal storage.
Please be sure that you are on the latest TWRP recovery. Keep im ind that this could also be an unofficial version!
If you want to contribute to the AICP or wannt see what is being worked on/merged, feel free to visit our Gerrit review system. (Link is at the bottom!!!)
Kernel source:
Put the Github link to your kernel HERE (mandatory), not posting the kernel source violates the GPL, and also violates the rules on XDA ...
ROM & Additional links:
AICP Gerrit Code Review
AICP on Github
AICP G+ community
Contributors:
(mention all the devs who have contributed to your device tree, kernel, vendor, etc,
only mention the main ones though, probably the top four or so, otherwise this list will be a mile long unless if you're a huge kanger xD)
ROM OS Version: 8.1.0 Oreo
ROM Kernel: Linux 3.4
Version Information:
Status: NIGHTLY
You want to see a "normal" night at the "DEV office", click here!!
XDA:DevDB Information
AICP, ROM for the Sony Xperia Z3 Tablet Compact
Contributors
koron393, 1indwurm (Akane Time!!), nickabg (for SGP611)
Source Code: https://github.com/AICP
ROM OS Version: 8.x Oreo
ROM Kernel: Linux 3.4.x
ROM Firmware Required: Require 23.5.A.1.291 bootloader / bootloader unlocked
Based On: LineageOS
Version Information
Status: Alpha
Created 2018-01-06
Last Updated 2020-02-17
Installation guide
Bootloader unlock required.
Update bootloader to stock 23.5.A.1.291.
(If you use lower version like lollipop, boot fails.)
TWRP is here!! Use "scorpion" for SGP621, "scorpion_windy" for SGP611/612.
Download ROM zip
Extract boot.img from ROM.zip
Reboot into bootloader mode
Flash extracted boot.img (fastboot flash boot boot.img)
Flash recovery to FOTAKernel (fastboot flash FOTAKernel TWRP_xxxx.img)
(Don't boot any stock ROMs.)
Reboot (fastboot reboot)
Press volume up button when LED light turns "pink" and boot into recovery mode (LED turns "orange")
Push ROM.zip
Wipe Data/System from menu
Install ROM.zip from menu
Reboot
Please read once
Please add logcat/dmesg full logs when you report bugs.
Code:
AicpExtras -> Log that s*it! -> (Check Logs)
OR
Code:
$ adb logcat > logcat_YYYYMMDD.log
$ adb shell su -c dmesg > dmesg_YYYYMMDD.log
Thanks for your help!!
OMG, THX, waiting for 611 build to test...
koron393 said:
AICP
Android Ice Cold Project
for Xperia Z3 Tablet Compact (scorpion/scorpion_windy) Unofficial
Using the ROM:
Q. How do I enable software buttons?
A. Until the navbar enabler is added, add the line qemu.hw.mainkeys=0 to the build.prop and then reboot, set it to 1 to disable it if you want. You can use an App like Kernel Audiutor for that.
Created 2018-01-06
Last Updated 2018-01-06
Click to expand...
Click to collapse
Last I checked, this device doesn't really have hardware buttons. Does this mean the ROM doesn't support software buttons and needs to be enabled manually?
Thanks for the ROM either way, will get ready to try it.
Update the thread.
And new build is up. Now ready for SGP611/SGP612.
If you install the ROMs, please read 1st to 3rd post.
Thanks
Chima2 said:
Last I checked, this device doesn't really have hardware buttons. Does this mean the ROM doesn't support software buttons and needs to be enabled manually?
Thanks for the ROM either way, will get ready to try it.
Click to expand...
Click to collapse
Hi.
This is just template.
This QA is from "AICP's xda template"
Not only for this tablet.
a fast feedback, I have installed this rom on my SGP611, everything seem to be working, even safetynet check passes without problem, the mayor surprise was the camera, despite of the camera recording, the quality of the photos is excellent, the only problem is one well-known, the volume of the speaker, but everything is ok.
Thank you for bring this fantastic rom and oreo to the scorpions.
Volume of the speaker problem?
Well-known??
I don't know. I can't understand.
Please explain properly.
koron393 said:
Volume of the speaker problem?
Well-known??
I don't know. I can't understand.
Please explain properly.
Click to expand...
Click to collapse
I mean, the volume goes down, when you start reproduce something, the volume starts wherever you set it, and then decrease. This only occurs when you use the speakers.
wulfiss said:
I mean, the volume goes down, when you start reproduce something, the volume starts wherever you set it, and then decrease. This only occurs when you use the speakers.
Click to expand...
Click to collapse
I agree, this problem exists for example in LOS from lowtraxx, but in AICP 7.1 this problem did not existed.
wulfiss said:
I mean, the volume goes down, when you start reproduce something, the volume starts wherever you set it, and then decrease. This only occurs when you use the speakers.
Click to expand...
Click to collapse
Read 3rd post
koron393 said:
Read 3rd post
Click to expand...
Click to collapse
Yeah, but I didn't have the tablet in that moment, but now yes.
I hope it helps you.
So my thoughts after flashing OREO on Windy.
First of all, cant express enough thanks to koron393 for his work, thinking about donating him.
What amazed me was: finaly 5GHz WIFI works for me: it stopped the moment I flashed a custom rom. years ago now. So it's a nice addition...
Camera works, except for movie, another problem with the cam is that its interface is obstructed by nav bar if you use one. It should disappear once in camera view...
I haven't found more issues for now...
Amazing....
@koron393 in Camera settings there is a button for changing storage between phone and sd card. When I change it to sd than it says "couldn´t access sd card". I also attached an Logcat so that you can look at this. Thanks for bringing an Oreo for our Windy.
Magisk 15.2 works
I confirm the volume issue. When on speaker the volume goes down right after you start playing a movie. I'm using HBO GO app.
---------- Post added at 04:09 PM ---------- Previous post was at 04:00 PM ----------
Concerning audio loudness issue: as far as I can remember, this fix made it work correct for LineageOS in the neighboring forum:
https://forum.xda-developers.com/cr...-dontbelive-marshmallow-stereomod-v1-t3366065
Hi people,
probably some one can help me pointing me into the right direction. I bricked my scorpion windy. thats what i did.
1. I was always switching between lowtraxxs and korons custom roms easily. made the mistake and just installed after all the wipes korons 8.x rom over lowtraxxs 7.x. Bricked
2. Read the instruction manual, and flashed boot and twrp image in the bootloader, hoping it would boot again, but doesn't do anything.
I just can get into the bootloader and thats it. Pressing power button and up while its off, results in 3 vibrations and that's it. when i charge the tablet the red led is blinking constantly (im sure wasnt like that before).
anyone with an idea for me?
thanks!
I did exactly the same: came from lowtrax' 7.1 rom, wiped in twrp and installed koron's 8.1, initially without gapps. But my scorpion windy booted and runs pretty smoothly. So maybe I was lucky, or your device broke for another reason.
Edit: can you flash a stock rom with Flashtool?
M1chiel said:
I did exactly the same: came from lowtrax' 7.1 rom, wiped in twrp and installed koron's 8.1, initially without gapps. But my scorpion windy booted and runs pretty smoothly. So maybe I was lucky, or your device broke for another reason.
Click to expand...
Click to collapse
damn. doesn't sound good for me. now i need to find some way to get it running again over the bootloader
What a surprise this rom!
My scorpion windy just updated.
Τhank you very much
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
AICP
Android Ice Cold Project
AICP is known by everyone as the "Ice Cold Project" that started on a Desire HD years ago (2012) and since then has evolved into a mature ROM with the BEST community that you can find!!!
Until Lollipop, the Rom has always been based on AOKP. Unfortunately, since AOKP stopped development (but made a comeback later), we changed our base to CM.
With the re-brand of CM to LineageOS (LAOS) we are now LAOS based with some tweaks from AOSP.
If there are any bugs, either we will sort them out or the LAOS team will if it concerns their code base. This rom isn't LAOS supported, so no need to report errors/bugs to them!!
Code:
#include <std_disclaimer.h>
/*
* Your warranty is now void.
*
* We are not responsible for bricked devices, dead SD cards,
* thermonuclear war or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at us for messing up your device, we will laugh at you. Hard & a lot.
*
*/
Feature list (rough Overview)
In the beginning we would like to thank:
LineageOS & CM (R.I.P.) team
@Maxwen and the rest of the OmniRom team
DU team
SlimRoms team
Resurrection Remix team
Community
...
@LorD ClockaN
@zipsnet
@eyosen
@semdoc
@Drgravy
@Hashbang173
@SpiritCroc
@wartomato
@eboye
plus the rest of the crazy bunch that we call "team"
...
We are paying for servers that build nightlies/weeklies and everything that comes with it, so EVERY DONATION will really be appreciated and be used to cover those expenses.
Thank you!!
Latest Stable Release Version 13.1
Download link: http://dwnld.aicp-rom.com/?device=m8qlul
Official builds will be deleted from our servers every month due to maintenance services.
We advise everyone to keep at least the latest or best working build on their device as a backup.
Maybe copy it to a cloud service or USB too.
Full Changelog link: http://dwnld.aicp-rom.com/?device=m8qlul
Google Apps: https://opengapps.org/?arch=arm64&api=8.1&variant=nano
HDR
Wireless display
WiFi Hotspot
The ROM should contain everything you need to enjoy Android Oreo. You don't need to install any Add-on's, simply download the latest ROM, GApps, flash it and go!
If you want the device to run the ROM "rooted", you can flash a root solution of your choice after the ROM Zipfile.
It is STRONGLY recommended to fully wipe your device before flashing and please avoid restoring system apps and system data with Titanium Backup as this can cause stability issues that are very hard to debug.
If you believe you know what you're doing - then fine, go ahead, but please don't complain if you experience any strange behavior.
How to flash:
(Again: Don't do it if you don't know it!)
1. Download the ROM and GApps and transfer them to your device.
2. Boot to recovery (TWRP 3.2.2 Required).
3. Wipe the System, Cache, Data and ART/Dalvik cache.
4. Flash the ROM Zipfile.
5. Flash the GApps (optional, needed for e.g. Google Playstore to work).
6. Flash the root solution of your choice (optional).
7. Reboot your device.
The ROM has GApps persistence in between dirty flashes, so you only have to flash them once!
The root solution should be flashed together with every OTA update (= ROM Update)
Currently Supported Root Solutions:
Magisk stable
Magisk versions higher than 14.0 doesn't require flash on every dirty flash depending on the device, some devices need you to flash it every time, unless your maintainer says otherwise it should be fine
KERNEL:
The kernel in this ROM follows LAOS source with custom additions.
PREREQUISITE FOR OTA:
To be able to flash using the built-in OTA app, TWRP recovery is needed.
You can still use the LAOS recovery and OTA app, but you will need to download the zip file and flash it manually from within your recovery. The Zipfile gets saved in the "aicp_ota" folder on your internal storage.
Please be sure that you are on the latest TWRP recovery. Keep in mind that this could also be an unofficial version!
If you want to contribute to the AICP or want see what is being worked on/merged, feel free to visit our Gerrit code review system. (Link is at the bottom!!!)
Kernel source: Here
ROM & Additional links:
AICP Gerrit Code Review
AICP on Github
AICP G+ community
Version Information:
Status: WEEKLY
You want to see a "normal" night at the "DEV office", click here!!
XDA:DevDB Information
[ROM][8.1][OFFICIAL][m8qlul] AICP 13.1 for HTC One M8s [Official Weeklies], ROM for the HTC One (M8)
Contributors
root-expert, voidzero
Source Code: http://github.com/AICP
ROM OS Version: 8.x Oreo
ROM Kernel: Linux 3.10.x
ROM Firmware Required: M firmware base
Based On: LineageOS
Version Information
Status: Stable
Beta Release Date: 2018-07-29
Created 2018-07-29
Last Updated 2018-08-25
Reserved
FAQ:
Before using the ROM:
Q. Can I have an ETA for the next build?
A. Yes, just look in the OP to see if your device is built on a nightly or weekly schedule.
Q. Does this ROM support custom kernels?
A. No. You can still use them, but discussion should go in the thread of the respective kernel. We don't offer support for bugs you might encounter while using them!
Q. Why doesn't this ROM support Xposed?
A. Xposed is a hack that is geared towards AOSP, custom ROM's modify the framework a lot, so Xposed can cause a ton of issues on custom ROM's. Now it might work for you, however it is not to be discussed in this thread, and you should refrain from posting bug reports.
Q. Alright, but I still want to flash Xposed, so which version do I need to install?
A. You will need to use the version arm64/arm/whatever for SDK 27.
Flashing the ROM:
Q. What do I need to know before flashing?
A. Check the install instructions in the first post...
Q. Can the builds be dirty flashed over each other?
A. Yes, however make a nandroid backup first as there is a chance of getting a bootloop or encountering bugs. Also bugs may only be reported on a clean flash.
Q. How do I dirty flash builds?
A. Wipe the System, Cache and ART/Dalvik cache. Flash the ROM, GApps (only needed if you wipe the system), your preferred root solution and reboot. Or just use the OTA app to preform that task for you.
Q. How do I flash kernel builds?
A1. If it's a .img file, boot into TWRP and go to the install page in TWRP, in the bottom right corner select "install image", select the desired kernel, then select "boot", then swipe to flash, then go back to the install screen and install your root method again, if you don't want to loose root and reboot.
A2. If it's a flashable ZIP, you can flash it together with a ROM update or separately. Go to the install page in TWRP, choose the kernel zip (or add it to the flash queue right after the ROM zip). Then add your root method to the queue if you don't want to loose root. Now swipe to flash, and then reboot.
Using the ROM:
Q. How do I enable software buttons?
A. Go to Aicp Extras/Navigation bar, and enable it.
Q. I installed a bad theme and now I'm getting a bootloop, how do I fix it?
A. In TWRP, flash the substratum rescue zip that's in the substratum folder on the internal storage.
Q. I keep losing root with Magisk, how do I fix it?
A. Check this out. If that doesn't work for you, ask for help in this thread, read or ask in the Magisk thread on XDA or just re-flash Magisk!
Q. I'm having issues with WhatsApp, how do I fix it?
A. Read this
Q. Do I need to provide a logcat if I'm reporting a bug?
A. If you want it to be fixed faster (or at all) then yes, you should definitely provide a logcat. (Note: Please just link the logcat from your GDrive, Dropbox, etc. and do not post the content here. Thanks.
Q. How do I get a logcat, what type should I get and more questions that can conveniently be answered by my pre-determined answer?
A1. Read this thoroughly. Also, here's a good app for getting logs: https://play.google.com/store/apps/details?id=com.tortel.syslog (Root needed).
A2. If you are already rooted, you can use the built-in feature to make a logcat and provide that. Just look into the others section in the AICP Extras main page.
Reserved
Hi!
This seems to be the perfect Oreo ROM, but... Google play keeps crashing on me... Any ideas?
And thanks for your work!
mjaxa said:
Hi!
This seems to be the perfect Oreo ROM, but... Google play keeps crashing on me... Any ideas?
And thanks for your work!
Click to expand...
Click to collapse
Ensure that you are flashing Gapps immediately after flashing the ROM without rebooting in between
-Chris
Indeed, that fixed it
Thanks!
I'm getting error 255 while trying to install this rom.
ddogg11 said:
I'm getting error 255 while trying to install this rom.
Click to expand...
Click to collapse
Install correct recovery, follow the instructions.
Well, I have twrp 3.2.2 and did all the steps corectly, but still have this issue.
I'm experiencing the same issue. I looked in the logs it was the update binery issue, so I put another in and the same issue. I even tried flashing the latest recovery that you linked in another thread but it is too alrge and can;t be flashed to that partition..
YorikR32 said:
I'm experiencing the same issue. I looked in the logs it was the update binery issue, so I put another in and the same issue. I even tried flashing the latest recovery that you linked in another thread but it is too alrge and can;t be flashed to that partition..
Click to expand...
Click to collapse
Αre you sure your phone is an HTC One M8s? HTC One M8 and HTC One M8s are two different phones..
Are you willing to provide any logs and info about your device?
root-expert said:
Αre you sure your phone is an HTC One M8s? HTC One M8 and HTC One M8s are two different phones..
Are you willing to provide any logs and info about your device?
Click to expand...
Click to collapse
Oh my, I am so sorry. You are 100% correct, I clicked in the wrong forum. I apologise for my error. I feel really stupid right now.
Another question - maybe anybody could share experiences - GPS is taking really long to get the fix. I never had M8s before, and have not had it with standard firmware, so I'm\not sure if this is the phone or the Oreo update having issues.... ?
Instagram video does not play video
Hi, I have a problem with Instagram and Snapchat applications.
Instagram does not play video posts, taking pictures does not work (camera view is black, camera change does not work), Stories video does not play.
Snapchat, on the other hand, works very slowly.
I tried with cache cleaning, reinstalling applications, battery saving mode off, nothing worked.
How can I fix this?
Hirons1 said:
How can I fix this?
Click to expand...
Click to collapse
I don't have the slightest idea.
exFAT SD Card not working.
Hi
Wondering if anyone can help me. Installed this ROM (nightly 18/8/18 with 3.2.3 TWRP) and everything seems to working OK. However, my external SD card when formatted in exFAT (64 gig) doesn't seem to work.
It is recognised and after the 'Setup' screen and configured to Removable Storage the content seems to be locked with the message "Content cannot be shown at this moment". This lasts indefinitely.
I've had to reformat my SD into FAT32 which isn't ideal as now I can't keep a couple of videos that I had on the card anymore.
Anyone had this and have a solution?
Thanks
BeOneOptica said:
Hi
Wondering if anyone can help me. Installed this ROM (nightly 18/8/18 with 3.2.3 TWRP) and everything seems to working OK. However, my external SD card when formatted in exFAT (64 gig) doesn't seem to work.
It is recognised and after the 'Setup' screen and configured to Removable Storage the content seems to be locked with the message "Content cannot be shown at this moment". This lasts indefinitely.
I've had to reformat my SD into FAT32 which isn't ideal as now I can't keep a couple of videos that I had on the card anymore.
Anyone had this and have a solution?
Thanks
Click to expand...
Click to collapse
Hello,
I'll fix this as soon as possible. I think i have forgotten to add exFAT driver in the kernel.
-Chris
root-expert said:
Hello,
I'll fix this as soon as possible. I think i have forgotten to ad exFAT driver in the kernel.
-Chris
Click to expand...
Click to collapse
Thanks Chris. Easy fix then :good:
Well done for your work on this ROM. Wish I'd used it when this phone was my daily.
BeOneOptica said:
Thanks Chris. Easy fix then :good:
Well done for your work on this ROM. Wish I'd used it when this phone was my daily.
Click to expand...
Click to collapse
Please try the new build and post here If the problem is solved
Hi Chris, was just about to but thought I'd ask first. Can I flash over the top or do I need to wipe down first? If I need to wipe down what's the minimum I need to wipe?
Thanks ?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
AICP
Android Ice Cold Project
AICP is known by everyone as the "Ice Cold Project" that started on a Desire HD years ago (2012) and since then has evolved into a mature ROM with the BEST community that you can find!!!
Until Android Lollipop, the ROM has always been based on AOKP. Unfortunately, since AOKP stopped development (but made a comeback later), we changed our base to CM.
With the re-brand of CM to LineageOS (LOS) we became LineageOS based with some tweaks from AOSP and we was based on the "Ground Zero Open Source Project" (GZOSP) for Android Pie.
For Android 10 we are now full AOSP-based.
Code:
#include <std_disclaimer.h>
/*
* Your warranty is now void.
*
* We are not responsible for bricked devices, dead SD cards,
* thermonuclear war or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications and if
* you point the finger at us for messing up your device, we will laugh at you. Hard & a lot.
*
*/
Feature list (rough overview)
In the beginning we would like to thank:
GZOSP team
LineageOS & CM (R.I.P.) team
@Maxwen and the rest of the OmniRom team
DU team
SlimRoms team
Resurrection Remix team
Community
...
@LorD ClockaN
@zipsnet
@eyosen
@semdoc
@SpiritCroc
@wartomato
@eboye
plus the rest of the crazy bunch that we call "team"
...
We are paying for servers that build nightlies/weeklies and everything that comes with it, so EVERY DONATION will really be appreciated and be used to cover those expenses.
Thank you!!
Download-Links:
ROM: https://dwnld.aicp-rom.com/
TWRP: https://github.com/CaptainThrowback/android_device_htc_m8/releases
GAPPS: https://opengapps.org/?arch=arm&api=10.0
Please note that official builds will be deleted from our servers every month due to maintenance services.
We advise everyone to keep at least the latest or best working build on their device as a backup.
Maybe copy it to a cloud service or USB too.
What's working
-wifi
-mobile data
-camera
-bluetooth
-audio
-DT2W
-AICP Themes
-GPS
-mobile data signal strength
What's not working
- encryption
FAQ:
Before using the ROM:
Q. Does this ROM support custom kernels officially?
A. No. You can still use them, but discussion should go in the thread of the respective kernel. We don't offer support for bugs you might encounter while using them!
Q. Why doesn't this ROM support Xposed?
A. Xposed is a hack that is geared towards AOSP. Custom ROMs modify the framework a lot, so Xposed can cause a ton of issues on custom ROMs. Now it might work for you, however it is not to be discussed in this thread, and you should refrain from posting bug reports.
Q. Alright, but I still want to flash Xposed, so which version do I need to install?
A. Xposed is not yet released for Pie, however you can try to use edxposed .
Flashing the ROM:
Q. What do I need to know before flashing?
A. Check the flashing instructions...
Q. Can the builds be dirty flashed over each other?
A. Yes, however make a nandroid backup first as there is a chance of getting a bootloop or encountering bugs. Also bugs may only be reported on a clean flash.
Q. How do I 'dirty flash' builds?
A. Wipe the System, Cache and ART/Dalvik cache. Flash the ROM, GApps (only needed if you wipe the system), your preferred root solution and reboot. Or just use the OTA app to preform that task for you.
Q. How do I flash kernel builds?
A1. If it's a .img file, boot into TWRP and go to the install page in TWRP, in the bottom right corner select "install image", select the desired kernel, then select "boot" as the destination, then swipe to flash, then go back to the install screen and install your root method again, if you don't want to loose root and reboot.
A2. If it's a flashable ZIP, you can flash it together with a ROM update or separately. Go to the install page in TWRP, choose the kernel zip (or add it to the flash queue right after the ROM zip). Then add your root method to the queue if you don't want to loose root. Now swipe to flash and reboot afterwards.
Using the ROM:
Q. I installed a bad theme and now I'm getting a bootloop, how do I fix it?
A. In TWRP, flash the substratum rescue zip that's in the substratum folder on the internal storage.
Q. I'm having issues with WhatsApp, how do I fix it?
A. Read this
Q. Do I need to provide a logcat if I'm reporting a bug?
A. If you want it to be fixed faster (or at all) then yes, you should definitely provide a logcat. (Note: Please just link the logcat from your GDrive, Dropbox, etc. and do not post the content here. Thanks.)
Q. How do I get a logcat, what type should I get and more questions that can conveniently be answered by my pre-determined answer?
A1. Read this thoroughly. Also, here's a good app for getting logs: https://play.google.com/store/apps/details?id=com.tortel.syslog (Root needed).
A2. If you are already rooted, you can use the built-in feature to make a logcat and provide that. Just look into the others section in the AICP Extras main page.
The ROM should contain everything you need to enjoy Android Pie. You don't need to install any Add-ons, simply download the latest ROM and GApps, then follow the flashing instructions and go!
If you want the device to run the ROM "rooted", you can flash a root solution of your choice after the ROM Zipfile.
It is STRONGLY recommended to fully wipe your device before flashing and please avoid restoring system apps and system data with Titanium Backup (or with any backup/restore app) as this can cause stability issues that are very hard to debug, restoring regular apps is fine though.
If you believe you know what you're doing - then fine, go ahead, but please don't complain if you experience any strange behavior.
How to flash for the first time:
(Again: Don't do it if you don't know!)
1. Download the ROM and GApps and transfer them to your device.
2. Boot to recovery (TWRP recommended).
3. Wipe the System, Cache, and Data (you might need to format the data partition!).
4. Flash the ROM Zipfile.
5. Flash the GApps (optional, needed for e.g. Google Playstore to work).
6. Reboot and set up your device, enable developer settings and in them OEM unlock/Advanced reboot/USB tethering.
7. Reboot back into TWRP recovery.
8. Flash the root solution of your choice (optional).
9. Reboot your device.
The procedure may vary from device to device and is a bit different on system updates!
The ROM has GApps persistence in between dirty flashes, so you only have to flash them once! This might differ on AvB Devices.
Currently supported Root Solution:
Magisk canary
PREREQUISITE FOR OTA ("Over-The-Air" Updates):
TWRP recovery is needed to be able to flash using the built-in OTA app.
Please make sure that you are on the latest TWRP recovery, keep in mind that this could also be an unofficial version!
On encrypted devices you will have to enter your PIN/password in TWRP before the process starts.
If you want to contribute to AICP, or want see what is being worked on/merged, feel free to visit our Gerrit code review system. (Link is at the bottom!!!)
Kernel source:
https://github.com/AICP/kernel_htc_msm8974
Device tree source:
https://github.com/AICP/device_htc_m8
ROM & Additional links:
AICP's Homepage
AICP Gerrit Code Review
AICP sources on Github
AICP Download page for official builds and media content
AICP Discord Community
AICP Telegram channel for server notifications on official builds[/B]
Contributors:
@Claymore1297
The following information is ONLY needed if you are not opening up a devdb thread on XDA!
ROM OS Version: 10.0 Android 10
Kernel: Linux 3.4.x
Requirements
TWRP: 3.3.1
Version Information:
Status: BETA
Release Date: 14-09-2019
You want to see a "normal" night at the "DEV office", click here!!
XDA:DevDB Information
AICP 15.0, ROM for the HTC One (M8)
Contributors
Claymore1297
ROM OS Version: Android 10
Based On: AOSP
Version Information
Status: Beta
Created 2019-10-10
Last Updated 2020-04-29
*reserved*
use TWRP linked in OP, which supports SAR.
many AICP features are still missing.
Available features so far:
-James DSP
-DT2S
-DT2W
-cpuinfo widget
-various tiles
-improved dialer settings
-batterybar (but colorized feature is missing right now)
-some notification customizations
-extended chargeinfo on lockscreen
-unlock pin scramble
-advanced reboot menu
-SysUI tuner
My Man! Thank you so much for your hard work!!
I was able to flash this using the latest TWRP but my M8 keeps rebooting to the fastboot/hboot screen. How do I boot into the ROM itself? My bootloader is unlocked but it may be old because I haven't used this device in ages.
Thanks!
TarekElsakka said:
I was able to flash this using the latest TWRP but my M8 keeps rebooting to the fastboot/hboot screen. How do I boot into the ROM itself? My bootloader is unlocked but it may be old because I haven't used this device in ages.
Thanks!
Click to expand...
Click to collapse
Hi,
Did you flash Magisk? If so, you need to make sure you use the latest Canary version (linked in the OP). I also recommend using @Captain_Throwback's TWRP from here: https://github.com/CaptainThrowback/android_device_htc_m8/releases rather than the one in the OP as it appears to be newer.
And for GApps you should be able to use the Beta OpenGApps for arm, but make sure you boot into the ROM once first before rebooting to recovery to flash them.
TWP
EDIT: It's also possible you're not on Marshmallow firmware, so make sure you update to that first before trying to flash the ROM.
@The_Walking_Playground Thank you so much for your reply. I have a strong feeling I am not on the latest firmware, so could you please instruct me on how to update to it? I am assuming I'd have to use fastboot in order to flash it? I was able to find an Android zip that has fastboot & adb and terminal works properly from there.
Thanks again!
I updated OP due GAPPS amd TWRP.
Please use this links:
TWRP:
https://github.com/CaptainThrowback/android_device_htc_m8/releases
GAPPS:
https://sourceforge.net/projects/opengapps/files/arm/beta/
TarekElsakka said:
@The_Walking_Playground Thank you so much for your reply. I have a strong feeling I am not on the latest firmware, so could you please instruct me on how to update to it? I am assuming I'd have to use fastboot in order to flash it? I was able to find an Android zip that has fastboot & adb and terminal works properly from there.
Thanks again!
Click to expand...
Click to collapse
Hi,
How to update firmware isn't a topic for this thread. If you search around XDA, there should be a thread for updating M8 firmware. All of the information and instructions you need should be there, and if you have any questions, that's where you should ask them.
TWP
Awesome
---------- Post added at 12:39 PM ---------- Previous post was at 12:29 PM ----------
The instructions say "
The ROM should contain everything you need to enjoy Android PIE. ????
Claymore1297 said:
I updated OP due GAPPS amd TWRP.
Please use this links:
TWRP:
https://github.com/CaptainThrowback/android_device_htc_m8/releases
GAPPS:
https://sourceforge.net/projects/opengapps/files/arm/beta/
Click to expand...
Click to collapse
Phone is not working for sprint version,I thought it was the usual sim lock and I unlocked it but upon flashing again it still shows network as unavailable and android.phone has stopped
Any one here have problem after flash gapps Pico 06-10-2019 beta ?
For me the phone not working property : can't enable internet data, dark theme not working, can't enable developer mode. And sometime buggy and fraze
ainaz said:
Any one here have problem after flash gapps Pico 06-10-2019 beta ?
For me the phone not working property : can't enable internet data, dark theme not working, can't enable developer mode. And sometime buggy and fraze
Click to expand...
Click to collapse
Download older gapps beta, newest one bugged everywhere.
AsrielDash said:
Download older gapps beta, newest one bugged everywhere.
Click to expand...
Click to collapse
Yea, i only want to ask is there same problem what I did
Ayoseun said:
Phone is not working for sprint version,I thought it was the usual sim lock and I unlocked it but upon flashing again it still shows network as unavailable and android.phone has stopped
Click to expand...
Click to collapse
+1
For those with problems try this gapps, they are working fine for me: open_gapps-arm-10.0-pico-20190928-BETA.zip (94M)
Almost everything is working perfectly for me but i found a couple of issues:
1. The phone and messaging apps don't switch to dark theme
2. Chrome constantly crashes(edge works fine)
3. Please include am or pm on the clock, it's killing me!!!
4. Please separate the ringtone and notification sound that'd be great!!!
Amazing work, still can't believe I'm using Android 10 on this 5 year old phone!!!
AkibAhned86 said:
Almost everything is working perfectly for me but i found a couple of issues:
1. The phone and messaging apps don't switch to dark theme
2. Chrome constantly crashes(edge works fine)
3. Please include am or pm on the clock, it's killing me!!!
4. Please separate the ringtone and notification sound that'd be great!!!
Amazing work, still can't believe I'm using Android 10 on this 5 year old phone!!!
Click to expand...
Click to collapse
Lucky you ,what variant do you use
Ayoseun said:
Lucky you ,what variant do you use
Click to expand...
Click to collapse
I'm using the single Sim variant (global version)
Also another issue i found is that YouTube videos are lagging a bit on YouTube vanced, don't know about the official YouTube app...
AkibAhned86 said:
Almost everything is working perfectly for me but i found a couple of issues:
1. The phone and messaging apps don't switch to dark theme
2. Chrome constantly crashes(edge works fine)
3. Please include am or pm on the clock, it's killing me!!!
4. Please separate the ringtone and notification sound that'd be great!!!
Amazing work, still can't believe I'm using Android 10 on this 5 year old phone!!!
Click to expand...
Click to collapse
Some more issues i found:
5. Videos lag in YouTube Vanced, not sure about official YouTube app
6. Cannot use Bluetooth headphones, they connect but break the playback of music and videos completely...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
AICP
Android Ice Cold Project
AICP is known by everyone as the "Ice Cold Project" that started on a Desire HD years ago (2012) and since then has evolved into a mature ROM with the BEST community that you can find!!!
Until Android Lollipop, the ROM has always been based on AOKP. Unfortunately, since AOKP stopped development (but made a comeback later), we changed our base to CM.
With the re-brand of CM to LineageOS (LOS) we became LineageOS based with some tweaks from AOSP and then changed to be based on the "Ground Zero Open Source Project" (GZOSP) for Android Pie.
We changed again for Android Q with a base of AOSP repositories and some additions from LineageOS for device specific repositories.
If there are any bugs, either we will sort them out, if it concerns our code base. This ROM isn't LineageOS supported, so there is no need to report errors/bugs to them!!
Code:
#include <std_disclaimer.h>
/*
* Your warranty is now void.
*
* We are not responsible for bricked devices, dead SD cards,
* thermonuclear war or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications and if
* you point the finger at us for messing up your device, we will laugh at you. Hard & a lot.
*
*/
Feature list (rough overview)
In the beginning we would like to thank:
GZOSP team
LineageOS & CM (R.I.P.) team
@maxwen and the rest of the OmniRom team
DU team
Resurrection Remix team
AOSiP team
Community
...
@LorD ClockaN
@eyosen
@semdoc
@SpiritCroc
@wartomato
@Miccia
plus the rest of the crazy bunch that we call "team"
...
We are paying for servers that build weeklies and everything that comes with this, so EVERY DONATION will really be appreciated and be used to cover those expenses.
Thank you!!
Latest Stable Release Version 15.0
Google Drive
Please note that official builds will be deleted from our servers every month due to maintenance services.
We advise everyone to keep at least the latest or best working build on their device as a backup.
Maybe copy it to a cloud service or USB too.
Full Changelog link: https://dwnld.aicp-rom.com/
(Just click the changelog button next to the download link in the list of builds available for your device)
Google Apps:
Tested on OpenGAPPS nano
Native screen recording broken
FAQ:
Before using the ROM:
Q. Can I have an ETA for the next build?
A. Yes, just look here to see what day your device is built on.
Q. Does this ROM support custom kernels officially?
A. No. You can still use them, but discussion should go in the thread of the respective kernel. We don't offer support for bugs you might encounter while using them!
Q. Why doesn't this ROM support Xposed?
A. Xposed is a hack that is geared towards AOSP. Custom ROMs modify the framework a lot, so Xposed can cause a ton of issues on custom ROMs. Now it might work for you, however it is not to be discussed in this thread, and you should refrain from posting bug reports.
Q. Alright, but I still want to flash Xposed, so which version do I need to install?
A. Information about Xposed, EdXposed or Riru Core can be obtained from the XPosed General forums .
Flashing the ROM:
Q. What do I need to know before flashing?
A. Check the flashing instructions...
Q. Can the builds be dirty flashed over each other?
A. Yes, this is the usual behaviour on flashing a new official build by (or using) the build-in updater service.
Q. How do I 'dirty flash' builds?
A. Wipe the System, Cache and ART/Dalvik cache. Flash the ROM, GApps (only needed if you wipe the system), your preferred root solution and reboot. Or just use the OTA app to preform that task for you.
Q. How do I flash kernel builds?
A1. If it's a .img file, boot into TWRP and go to the install page in TWRP, in the bottom right corner select "install image", select the desired kernel, then select "boot" as the destination, then swipe to flash, then go back to the install screen and install your root method again, if you don't want to loose root and reboot.
A2. If it's a flashable ZIP, you can flash it together with a ROM update or separately. Go to the install page in TWRP, choose the kernel zip (or add it to the flash queue right after the ROM zip). Then add your root method to the queue if you don't want to loose root. Now swipe to flash and reboot afterwards.
Using the ROM:
Q. I installed a bad theme and now I'm getting a bootloop, how do I fix it?
A. In TWRP, flash the substratum rescue zip that's in the substratum folder on the internal storage.
Q. I'm having issues with WhatsApp, how do I fix it?
A. Read this
Q. Do I need to provide a logcat if I'm reporting a bug?
A. If you want it to be fixed faster (or at all) then yes, you should definitely provide a logcat AND the model name. (Note: Please just link the logcat from your GDrive, Dropbox, etc. and do not post the content here. Thanks.)
Q. How do I get a logcat, what type should I get and more questions that can conveniently be answered by my pre-determined answer?
A1. Read this thoroughly. Also, here's a good app for getting logs: https://play.google.com/store/apps/details?id=com.tortel.syslog (Root needed).
A2. If you are already rooted, you can use the built-in feature to make a logcat and provide that. Just look into the others section in the AICP Extras main page.
The ROM should contain everything you need to enjoy Android Q. You don't need to install any Add-ons, simply download the latest ROM and GApps, then follow the flashing instructions and go!
If you want the device to run the ROM "rooted", you can flash a root solution of your choice after the ROM Zipfile.
It is STRONGLY recommended to fully wipe your device before flashing and please avoid restoring system apps and system data with Titanium Backup (or with any backup/restore app) as this can cause stability issues that are very hard to debug, restoring regular apps is fine though.
If you believe you know what you're doing - then fine, go ahead, but please don't complain if you experience any strange behavior.
How to flash for the first time:
(Again: Don't do it if you don't know!)
1. Download the ROM and GApps and transfer them to your device.
2. Boot to recovery (TWRP recommended).
3. Wipe the System, Cache, and Data (you might need to format the data partition!).
4. Flash the ROM Zipfile.
5. Flash the GApps (optional, needed for e.g. Google Playstore to work), GApps are already included for some a/b devices.
6. Reboot and set up your device, enable developer settings and in them OEM unlock/Advanced reboot/USB tethering.
7. Reboot back into TWRP recovery.
8. Flash the root solution of your choice (optional).
9. Reboot your device.
The procedure may vary from device to device and is a bit different on system updates!
Optional install instructions: Download images.zip, decompress, flash in fastbootd
images.zip
The ROM has GApps persistence in between dirty flashes, so you only have to flash them once! This might differ on AvB Devices.
Currently supported Root Solution:
Magisk stable
Magisk versions >= 20.4 don't usually need to be flashed on every dirty flash.
Depending on the device, you may need to flash it every time, unless your maintainer says otherwise, you should be fine.
If you want to contribute to AICP, or want see what is being worked on/merged, feel free to visit our Gerrit code review system. (Link is at the bottom!!!)
Kernel source:
GitHub - Odin1101/Project-Sofia: Main branch is Vache's 4.14.170 Kernel. Upstream branch is the 4.14.202 Kernel.
Main branch is Vache's 4.14.170 Kernel. Upstream branch is the 4.14.202 Kernel. - GitHub - Odin1101/Project-Sofia: Main branch is Vache's 4.14.170 Kernel. Upstream branch is the 4.14.202 Ke...
github.com
Device tree source:
GitHub - asineth0/android_device_motorola_sofiar: Device tree for Moto G8/G8 Power
Device tree for Moto G8/G8 Power. Contribute to asineth0/android_device_motorola_sofiar development by creating an account on GitHub.
github.com
Vendor source:
GitHub - asineth0/android_vendor_motorola_sofiar: Vendor tree for Moto G8/G8 Power
Vendor tree for Moto G8/G8 Power. Contribute to asineth0/android_vendor_motorola_sofiar development by creating an account on GitHub.
github.com
ROM & Additional links:
AICP's Homepage
AICP Gerrit Code Review
AICP sources on Github
AICP Download page for official builds and media content
AICP Discord Community
AICP Telegram channel for server notifications on official builds
Contributors:
Vache, Asineth, Beetle, for help with device sources and building help.
Odin for his kernel, and some changes that really helped the build!
ROM OS Version: 10.x
Kernel: 4.14.x
Version Information:
Status: Stable
Release Date: 12-22-20
works fine on my sofiar. I had trouble with crdroid and wasn't able to get it to boot with gapps for some reason. and I'm tired of factory resetting every update
UPDATE:
Fixed overlay detection on RAV (G8, G Fast). No need to enter code to enable overlay.
Enjoy the new boot animation!
Links updated in OP
Changelog: Changelog.txt
Is location not working a problem for anyone else?
billard412 said:
Is location not working a problem for anyone else?
Click to expand...
Click to collapse
I haven't seen any location issues. Make sure all of your perms are set correctly and all location services are turned on.
mad_fitter said:
I haven't seen any location issues. Make sure all of your perms are set correctly and all location services are turned on.
Click to expand...
Click to collapse
Yup I did that. Initially Waze and gmaps were having trouble but the issue seemed to fix itself. However, I deliver for doordash and postmates and can't get either to work because they never find my location.
Update.
Device changes: Add apns to config.
Links updated in OP.
I need help, no matter what i do with my moto G fast xt2045-3 I can never figure out how to install the custom rom after the bootloader has been unlocked, i hace done every step but i get pre verification error
dandu3 said:
works fine on my sofiar. I had trouble with crdroid and wasn't able to get it to boot with gapps for some reason. and I'm tired of factory resetting every update
Click to expand...
Click to collapse
how did you get it to work twrp throws me errors moto gfast xt2045-3
hmm it looks like my xt2045-2 is stuck on boot screen do i need stock android 10
Demed333 said:
hmm it looks like my xt2045-2 is stuck on boot screen do i need stock android 10
Click to expand...
Click to collapse
Yeap! All the custom roms need the Stock Android 10 base. If you mess up something you must flash stock Android-10. Be carefull because downgrading is not possible due to bootloader lock. On Moto G8 the bootloader is not totally unlocked. It is unlocked in the sense that you can flash all the other things BUT not another engineered bootloader. So the bootloader can only be same version or newer, never older, never unofficial.
siokara said:
Yeap! All the custom roms need the Stock Android 10 base. If you mess up something you must flash stock Android-10. Be carefull because downgrading is not possible due to bootloader lock. On Moto G8 the bootloader is not totally unlocked. It is unlocked in the sense that you can flash all the other things BUT not another engineered bootloader. So the bootloader can only be same version or newer, never older, never unofficial.
Click to expand...
Click to collapse
is it even possible? If it's can you make a video or something to do that
Demed333 said:
is it even possible? If it's can you make a video or something to do that
Click to expand...
Click to collapse
motorola added antirollback in january 2022 update so if youre on it (or newer) sadly you cant downgrade to older firmware.
Demed333 said:
is it even possible? If it's can you make a video or something to do that
Click to expand...
Click to collapse
If you flashed stock Android-11 you are in trouble because you now have a very new bootloader version and I don't know if you can revert to stock Android-10. Personally I haven't done this because I was paying attention to the requirements the various rom developers were describing in their posts. You must try it. I hope you get lucky.
siokara said:
If you flashed stock Android-11 you are in trouble because you now have a very new bootloader version and I don't know if you can revert to stock Android-10. Personally I haven't done this because I was paying attention to the requirements the various rom developers were describing in their posts. You must try it. I hope you get lucky.
Click to expand...
Click to collapse
Yez i did that and bricked my device but Blank flash works. And i Sony think i wanna try doing ut again
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
AICP
Android Ice Cold Project
AICP is known by everyone as the "Ice Cold Project" that started on a Desire HD years ago (2012) and since then has evolved into a mature ROM with the BEST community that you can find!!!
Until Android Lollipop, the ROM has always been based on AOKP. Unfortunately, since AOKP stopped development (but made a comeback later), we changed our base to CM.
With the re-brand of CM to LineageOS (LOS) we became LineageOS based with some tweaks from AOSP and then changed to be based on the "Ground Zero Open Source Project" (GZOSP) for Android Pie.
We changed again for Android Q with a base of AOSP repositories and some additions from LineageOS for device specific repositories.
If there are any bugs, either we will sort them out, if it concerns our code base. This ROM isn't LineageOS supported, so there is no need to report errors/bugs to them!!
Code:
#include <std_disclaimer.h>
/*
* Your warranty is now void.
*
* We are not responsible for bricked devices, dead SD cards,
* thermonuclear war or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications and if
* you point the finger at us for messing up your device, we will laugh at you. Hard & a lot.
*
*/
Feature list (rough overview)
In the beginning we would like to thank:
GZOSP team
LineageOS & CM (R.I.P.) team
@maxwen and the rest of the OmniRom team
DU team
Resurrection Remix team
AOSiP team
Community
...
@LorD ClockaN
@eyosen
@semdoc
@SpiritCroc
@wartomato
@Miccia
plus the rest of the crazy bunch that we call "team"
...
We are paying for servers that build weeklies and everything that comes with this, so EVERY DONATION will really be appreciated and be used to cover those expenses.
Thank you!!
Latest Stable Release Version 15.0
Download link: https://dwnld.aicp-rom.com/
Please note that official builds will be deleted from our servers every month due to maintenance services.
Starting with AICP 15 we will be storing a copy of the most recent release here: https://media.aicp-rom.com/vault/.
Full Changelog link: https://dwnld.aicp-rom.com/
(Just click the changelog button next to the download link in the list of builds available for your device)
Google Apps:
OpenGapps
You tell...
FAQ:
Before using the ROM:
Q. Can I have an ETA for the next build?
A. Yes, just look here to see what day your device is built on.
Q. Does this ROM support custom kernels officially?
A. No. You can still use them, but discussion should go in the thread of the respective kernel. We don't offer support for bugs you might encounter while using them!
Q. Why doesn't this ROM support Xposed?
A. Xposed is a hack that is geared towards AOSP. Custom ROMs modify the framework a lot, so Xposed can cause a ton of issues on custom ROMs. Now it might work for you, however it is not to be discussed in this thread, and you should refrain from posting bug reports.
Q. Alright, but I still want to flash Xposed, so which version do I need to install?
A. Information about Xposed, EdXposed or Riru Core can be obtained from the XPosed General forums .
Flashing the ROM:
Q. What do I need to know before flashing?
A. Check the flashing instructions...
Q. Can the builds be dirty flashed over each other?
A. Yes, this is the usual behaviour on flashing a new official build by (or using) the build-in updater service.
Q. How do I 'dirty flash' builds?
A. Wipe the System, Cache and ART/Dalvik cache. Flash the ROM, GApps (only needed if you wipe the system), your preferred root solution and reboot. Or just use the OTA app to preform that task for you.
Q. How do I flash kernel builds?
A1. If it's a .img file, boot into TWRP and go to the install page in TWRP, in the bottom right corner select "install image", select the desired kernel, then select "boot" as the destination, then swipe to flash, then go back to the install screen and install your root method again, if you don't want to loose root and reboot.
A2. If it's a flashable ZIP, you can flash it together with a ROM update or separately. Go to the install page in TWRP, choose the kernel zip (or add it to the flash queue right after the ROM zip). Then add your root method to the queue if you don't want to loose root. Now swipe to flash and reboot afterwards.
Using the ROM:
Q. I installed a bad theme and now I'm getting a bootloop, how do I fix it?
A. In TWRP, flash the substratum rescue zip that's in the substratum folder on the internal storage.
Q. I'm having issues with WhatsApp, how do I fix it?
A. Read this
Q. Do I need to provide a logcat if I'm reporting a bug?
A. If you want it to be fixed faster (or at all) then yes, you should definitely provide a logcat AND the model name. (Note: Please just link the logcat from your GDrive, Dropbox, etc. and do not post the content here. Thanks.)
Q. How do I get a logcat, what type should I get and more questions that can conveniently be answered by my pre-determined answer?
A1. Read this thoroughly. Also, here's a good app for getting logs: https://play.google.com/store/apps/details?id=com.tortel.syslog (Root needed).
A2. If you are already rooted, you can use the built-in feature to make a logcat and provide that. Just look into the others section in the AICP Extras main page.
The ROM should contain everything you need to enjoy Android Q. You don't need to install any Add-ons, simply download the latest ROM and GApps, then follow the flashing instructions and go!
If you want the device to run the ROM "rooted", you can flash a root solution of your choice after the ROM Zipfile.
It is STRONGLY recommended to fully wipe your device before flashing and please avoid restoring system apps and system data with Titanium Backup (or with any backup/restore app) as this can cause stability issues that are very hard to debug, restoring regular apps is fine though.
If you believe you know what you're doing - then fine, go ahead, but please don't complain if you experience any strange behavior.
How to flash for the first time:
(Again: Don't do it if you don't know!)
1. Download the ROM and GApps and transfer them to your device.
2. Boot to recovery (TWRP recommended).
3. Wipe the System, Cache, and Data (you might need to format the data partition!).
4. Flash the ROM Zipfile.
5. Flash the GApps (optional, needed for e.g. Google Playstore to work), GApps are already included for some a/b devices.
6. Reboot and set up your device, enable developer settings and in them OEM unlock/Advanced reboot/USB tethering.
7. Reboot back into TWRP recovery.
8. Flash the root solution of your choice (optional).
9. Reboot your device.
The procedure may vary from device to device and is a bit different on system updates!
The ROM has GApps persistence in between dirty flashes, so you only have to flash them once! This might differ on AvB Devices.
Currently supported Root Solution:
Magisk stable
Magisk versions >= 20.3 don't usually need to be flashed on every dirty flash.
Depending on the device, you may need to flash it every time, unless your maintainer says otherwise, you should be fine.
PREREQUISITE FOR OTA ("Over-The-Air" Updates):
TWRP recovery is needed to be able to flash using the built-in OTA app.
Please make sure that you are on the latest TWRP recovery, keep in mind that this could also be an unofficial version!
On encrypted devices you will have to enter your PIN/password in TWRP before the process starts.
If you want to contribute to AICP, or want see what is being worked on/merged, feel free to visit our Gerrit code review system. (Link is at the bottom!!!)
Kernel source:
https://github.com/marcost2/kernel_motorola_msm8953
Device tree source:
"https://github.com/marcost2/android_device_motorola_albus
Vendor source:
https://github.com/marcost2/proprietary_vendor_motorola
ROM & Additional links:
AICP's Homepage
AICP Gerrit Code Review
AICP sources on Github
AICP Download page for official builds and media content
AICP Discord Community
AICP Telegram channel for server notifications on official builds
Contributors:
EmaMaker, erfanoabdi, vacheounet, Npjohnson, JeanGraff30, jefferson1979, JarlPenguin
ROM OS Version: 10.0.x
Kernel: Linux 3.18.124
Version Information:
Status: WEEKLY
Release Date: 02-26-2021
You want to see a "normal" night at the "DEV office", click here!!
02-27
Went official
02-26
Initial Release
It's official now.
I tried this rom, it installed fine, but during setup (and after setup) it keeps rebooting after only ca 30 sec uptime.
Аnd just like on other rom on Android 10 does not work WearOs app
lungan said:
I tried this rom, it installed fine, but during setup (and after setup) it keeps rebooting after only ca 30 sec uptime.
Click to expand...
Click to collapse
Weird, are you using latest twrp (3.4 or 3.5)?
marcost22 said:
Weird, are you using latest twrp (3.4 or 3.5)?
Click to expand...
Click to collapse
Actually not, Iwas using 3.2.2-r23. As said, it installed fine, and I can even boot and run, but then again it reboots after 30 second uptime everytime.
Do you think an old version of TWRP could mess up the installation, and thus, even if the installation runs fine, the ROM is corruptively installed afterwards?
That really sounds like you were using Oreo firmware. But assuming that you are using pie modem, yes, old twrp could cause some issues. Also, we are official again for twrp, so you can just download from there
Dear developer.
The Wear Os application does not start on your firmware,
and when theJBL mode is connected, the alarm clock does not play
I'll look into wearos
I know, this is a issue that plagues all Z devices on custom roms, and we are trying to fix it
Ah, so refreshing to see an official rom for our device! Works flawlessly, thank you!
Greetings from Germany
Thanks for your work!
My bluetooth doesnt work. When i start it, it doesnt run and an info box opens with the text " Bluetooth terminates repeatedly " and three choices...app information, close app and Copy the url of the crash report .
bluetooth is not important to me, I just wanted to point out the problem to you ... maybe others have the same
ad astra
Hack
You need to be on Pie firmware for this rom, otherwise you get, well, that
oh...ok...thanks for the fast answer
This looks pretty cool, great job! I have a few questions:
1) Does encryption work?
2) What about Always on Display? Is it the same experience as in stock ROM?
3) And finally, does one-button navigation work? (The gesture navigation using the fingerprint sensor.)
Thanks!
1) Yes! It does
2) You can enable it yeah; I like to use it only when it's charging and there's an option for that too. I can't say it's the same as stock as i haven't been on stock in like 2 years
3) Yes, yes it does
is wear os app not working issue resolved yet?
Hi. Today I've installed this rom and later I've updated to 20210327 WEEKLY. Camera doesn´t work and when I plugged the charger or the usb cable front flash enables. Any solution?
Thx
ddhernandez said:
Hi. Today I've installed this rom and later I've updated to 20210327 WEEKLY. Camera doesn´t work and when I plugged the charger or the usb cable front flash enables. Any solution?
Thx
Click to expand...
Click to collapse
Hi!, what do you mean camera doesn't work? Could you be a bit more specific about what app you are using, errors?
Also that's not the front flash, that's the notification LED, and it turning on during charging can be disabled under Settings -> AICP Extra -> Notifications -> Battery LED