Related
Hi there, I'm new here but I have been following this forum for a long time.
Here's my problem:
I own a LGP990 with DJANGO rom. apart from the random stuck in the DJANGO loading screen which required me to reinstall it, it was all working fine.
Until yesterday, when I plugged it to recharge. The battery charged for a while and then got stuck for hours when almost done.
I unplugged it and try to turn it on but since that moment it always gets stuck at LG logo screen and when plugged it doesn't display any battery charging. I then tried to start recovery to reinstall from zip as I did every time it got stuck in the django loading screen, but recovery does not start.
No problem, I thought, lets smartflash/nvflash a stock rom and i'm good to go. Wrong, the phone won't even get recognized by windows, though I installed the driver several times (disabling driver signature as well) and running it as admin; i tried different driver versions, different usb cables... It does not even play that background sound when plugging usb devices...
I'm using windows 7 32bit.
That's it, I have ran out of ideas... anyone got one? (besides sending it to assistance, since warranty is voided)
little edit: whenever i plug the battery the phone start by itself!
gaernik said:
Hi there, I'm new here but I have been following this forum for a long time.
Here's my problem:
I own a LGP990 with DJANGO rom. apart from the random stuck in the DJANGO loading screen which required me to reinstall it, it was all working fine.
Until yesterday, when I plugged it to recharge. The battery charged for a while and then got stuck for hours when almost done.
I unplugged it and try to turn it on but since that moment it always gets stuck at LG logo screen and when plugged it doesn't display any battery charging. I then tried to start recovery to reinstall from zip as I did every time it got stuck in the django loading screen, but recovery does not start.
No problem, I thought, lets smartflash/nvflash a stock rom and i'm good to go. Wrong, the phone won't even get recognized by windows, though I installed the driver several times (disabling driver signature as well) and running it as admin; i tried different driver versions, different usb cables... It does not even play that background sound when plugging usb devices...
I'm using windows 7 32bit.
That's it, I have ran out of ideas... anyone got one? (besides sending it to assistance, since warranty is voided)
little edit: whenever i plug the battery the phone start by itself!
Click to expand...
Click to collapse
thats an issue I had, power button is making funny games, to enter recovery keep the vol- button pressed before you return the battery.
It always worked for me. let me know if it works.
this is what u have to do man...
http://www.ibtimes.co.uk/articles/40...timus-p990.htm
http://androidadvices.com/unbrick-lg...hone-tutorial/
http://progmaq.es/cm10/progmaq-defau...10-20121105.7z
http://progmaq.es/cm10/progmaq-defau...10-20121105.7z
The flasher with NVFlash clears all memory, including the Internal SD., so make a backup if u can..
Download this file: http://bayfiles.com/file/yKZL/eGZ31A/driver.rar The pack includes the APX driver (folder driver)
http://www.putlocker.com/file/4CEDEB7E0893B6F1
1.- Remove the battery to the phone.
2.- Press and hold Vol- and Vol+ and without releasing the 2 keys connect the USB cable to the PC
3.- Go to the progmaq-default-cm-10-20121105 folder and run flash icon... folow instruction., wait wait wait Enjoy!
massimo69 said:
thats an issue I had, power button is making funny games, to enter recovery keep the vol- button pressed before you return the battery.
It always worked for me. let me know if it works.
Click to expand...
Click to collapse
what do you mean before you return the battery? i kept vol- button before removing and then plugging it to the usb but still not detecting
interr said:
The flasher with NVFlash clears all memory, including the Internal SD., so make a backup if u can..
Download this file: The pack includes the APX driver (folder driver)
1.- Remove the battery to the phone.
2.- Press and hold Vol- and Vol+ and without releasing the 2 keys connect the USB cable to the PC
3.- Go to the progmaq-default-cm-10-20121105 folder and run flash icon... folow instruction., wait wait wait Enjoy!
Click to expand...
Click to collapse
4/6 of your link are broken dude
gaernik said:
what do you mean before you return the battery? i kept vol- button before removing and then plugging it to the usb but still not detecting
Click to expand...
Click to collapse
I meant to enter recovery. If your phone turns on when you put in the battery, the power button is stuck in a connected position so to enter recovery remove the battery, press the vol- and then insert the battery. If you get your phone to enter recovery and reflash the rom I will tell you what to try to fix the issue.
1.)remove battery
2.)press volume - and volume +
3.)connect phone to pc via usb
4.)download apx driver
5.)(go to device manager install manually apx driver, select the folder where you downloaded and extracted apx ini driver file
6.)flash using nvflash
7.)enjoy.
massimo69 said:
I meant to enter recovery. If your phone turns on when you put in the battery, the power button is stuck in a connected position so to enter recovery remove the battery, press the vol- and then insert the battery. If you get your phone to enter recovery and reflash the rom I will tell you what to try to fix the issue.
Click to expand...
Click to collapse
doing as you said brings me to the "s/w upgrading" screen, not into recovery
wawyed said:
1.)remove battery
2.)press volume - and volume +
3.)connect phone to pc via usb
4.)download apx driver
5.)(go to device manager install manually apx driver, select the folder where you downloaded and extracted apx ini driver file
6.)flash using nvflash
7.)enjoy.
Click to expand...
Click to collapse
problem is that nvflash says "no usb device found" and phone does not appear in device manager
gaernik said:
doing as you said brings me to the "s/w upgrading" screen, not into recovery
Click to expand...
Click to collapse
thats because you have your usb connected
massimo69 said:
thats because you have your usb connected
Click to expand...
Click to collapse
it says so even with usb disconnected :|
gaernik said:
it says so even with usb disconnected :|
Click to expand...
Click to collapse
Then use the AIO toolkit to smartflash a new rom
massimo69 said:
Then use the AIO toolkit to smartflash a new rom
Click to expand...
Click to collapse
as I said earlier, nvflash/aio toolkit give me a "usb device not found" error
gaernik said:
doing as you said brings me to the "s/w upgrading" screen, not into recovery
problem is that nvflash says "no usb device found" and phone does not appear in device manager
Click to expand...
Click to collapse
if you can enter s/w upgrading then you can use smartflash to flash a new rom.
gaernik said:
as I said earlier, nvflash/aio toolkit give me a "usb device not found" error
Click to expand...
Click to collapse
in AIO you have an option to smartflash roms not nvflash. You need to unpack a KDZ rom and install the ROM via smartflash
all the instructions are in the op of the AIO toolkit
the problem still remains, no phone detected and no com port appears in smartflash...
gaernik said:
the problem still remains, no phone detected and no com port appears in smartflash...
Click to expand...
Click to collapse
mmmmhhhhh..... change usb port, change cable, reinstall the drivers. other than that I am at loss
AIO tool has an option to install Nvflash driver. Its the last option in a different color.
Or you could try to reinstall LG driver. I just downloaded the latest driver from lg support tool today. It works fine.
And be noted that you have to hold down both volume up and down while plugging the USB cable to enter nvflash mode. Holding vol down while plugging the cable in will enter boot loader mode which is not the same thing. Remember to remove the battery first of all.
Sent from my LG-P990 using xda premium
massimo69 said:
mmmmhhhhh..... change usb port, change cable, reinstall the drivers. other than that I am at loss
Click to expand...
Click to collapse
done all of that, nothing worked...
mintjustin said:
AIO tool has an option to install Nvflash driver. Its the last option in a different color.
Or you could try to reinstall LG driver. I just downloaded the latest driver from lg support tool today. It works fine.
And be noted that you have to hold down both volume up and down while plugging the USB cable to enter nvflash mode. Holding vol down while plugging the cable in will enter boot loader mode which is not the same thing. Remember to remove the battery first of all.
Sent from my LG-P990 using xda premium
Click to expand...
Click to collapse
installed the driver from support tool but still cant get it recognized neither by smartflash nor nvflash
http://www.ibtimes.co.uk/articles/408044/20121124/unbrick-tool-lg-optimus-p990.htm
http://androidadvices.com/unbrick-lg-optimus-2x-p990-android-phone-tutorial/
http://progmaq.es/cm10/progmaq-default-cm-10-20121105.7z
http://progmaq.es/cm10/progmaq-default-cm-10-20121105.7z
The flasher with NVFlash clears all memory, including the Internal SD., so make a backup if u can..
Download this file: http://bayfiles.com/file/yKZL/eGZ31A/driver.rar The pack includes the APX driver (folder driver) and install the drivers
http://www.putlocker.com/file/4CEDEB7E0893B6F1
1.- Remove the battery to the phone.
2.- Press and hold Vol- and Vol+ and without releasing the 2 keys connect the USB cable to the PC
3.- Go to the progmaq-default-cm-10-20121105 folder and run flash icon... folow instruction., wait wait wait Enjoy!
guys I appreciate all your help but nothing worked. still windows does not detect it, I even plugged to a pc that used to see it :|
lg optimus 2x ics root
gaernik said:
guys I appreciate all your help but nothing worked. still windows does not detect it, I even plugged to a pc that used to see it :|
Click to expand...
Click to collapse
hey...ur problem solved??
Hello,
I have some problems trying to flash my XZ. I'm using Xperia Flashing Tool 0.9.10.2 beta6 on Windows 8 x64 and whenever I try to flash my XZ flashing tool "gets stuck at "Device connected in flash mode" message after which it gets reconnected and if I try again same thing will happen.
So my question is, am I doing something wrong and if so, please advise.
Bluffer said:
Hello,
I have some problems trying to flash my XZ. I'm using Xperia Flashing Tool 0.9.10.2 beta6 on Windows 8 x64 and whenever I try to flash my XZ flashing tool "gets stuck at "Device connected in flash mode" message after which it gets reconnected and if I try again same thing will happen.
So my question is, am I doing something wrong and if so, please advise.
Click to expand...
Click to collapse
have you correctly installed the drivers for it, connect phone in flashmode and does windows drivers load, also in flashtool go to devices>conected devices and what does it say
Maddhouse said:
have you correctly installed the drivers for it, connect phone in flashmode and does windows drivers load, also in flashtool go to devices>conected devices and what does it say
Click to expand...
Click to collapse
I think drivers are installed fine. Screenshot is below.
no doesnt look it, under ADB devices there is no device, Reinstall drivers and try again. Try the way in my sig for win 8
Unfortunately same thing happens - check screenshot below.
Bluffer said:
Unfortunately same thing happens - check screenshot below.
Click to expand...
Click to collapse
thats better you now have a ADB device installed, you should now be able to put your phone into flashmode
power off your phone with usb diconnected, hold vol down and reconnect turned off phone to usb and you should now get green led and flashtool will say device connected in flashmode but you only have about a min in flashmode before phone reboots
Thank you for your help and effort but even now it keeps disconnecting device. I don't know where the problem is, maybe I'm not doing something as I should.
This is the procedure I was trying:
1) I select Flash device in flash tool
2) I select Flashmode mode
3) I choose which firmware to flash and click Flash so flash tool can start it's magic
4) When flash tool shows message that I can remove my device from USB and turn it off I do so
5) I also press volume down and reconnect the device with the PC.
6) Problem happens here
what about if flashtool isnt ready to flash file, does flashtool pick it up (4 and 5)
it will say device connected in flashmode with green led
Yeah, it does pick it up and displays a message "Device connected in flash mode" and after awhile "Device disconnected".
Bluffer said:
Yeah, it does pick it up and displays a message "Device connected in flash mode" and after awhile "Device disconnected".
Click to expand...
Click to collapse
good yer i think its about a min, now try and download another FTF file
part 1
part 2
that works i have got loads of people to flash that
edit: i made it so its self extract version then there is a FTF file for flashtool
As you suggested the problem was in faulty FTF. It's working like a charm now!
Thank you once again!
Bluffer said:
As you suggested the problem was in faulty FTF. It's working like a charm now!
Thank you once again!
Click to expand...
Click to collapse
Good Good, What wasnt helping was you didnt have drivers installed aswell, now you just have to root and your sorted :highfive:
hey i m having same with my x8 after i accidently kept stock rom for nalf kernal... nw i m nt able to open cmw in phone...plz help..
Hi everyone. I need help to solve my brick phone trouble.
This my history:
I tried to flash a Moto X 1058 with a different firmware to be able to introduce a subsidy unlock code. That menu is locked on carrier's original firmware. So, did it with a wrong version and mess the phone, now it restarts automatically with a "boot failure" message and battery is not charging with wall charger.
I got this factory cable mentioned in another post and when is plugged screen says "Battery ok" "Transfer mode: USB Connected" in green text, but Windows won't recognize, says: "Unknown device". Y already tried different ports, different computers, uninstalling and reinstalling drivers but nothing.
I must say that before to use the factory cable, have the "battery low" red text message and once in any of those multiple press-hold keys sequence attempts (CAN'T REMEMBER WICH ONE) I was able to connect to the phone and windows recongnized via "fastboot device", but couldn't do a flash process due to the low battery state.
Any advise? Thanks in advance.
go_nathan said:
Hi everyone. I need help to solve my brick phone trouble.
This my history:
I tried to flash a Moto X 1058 with a different firmware to be able to introduce a subsidy unlock code. That menu is locked on carrier's original firmware. So, did it with a wrong version and mess the phone, now it restarts automatically with a "boot failure" message and battery is not charging with wall charger.
I got this factory cable mentioned in another post and when is plugged screen says "Battery ok" "Transfer mode: USB Connected" in green text, but Windows won't recognize, says: "Unknown device". Y already tried different ports, different computers, uninstalling and reinstalling drivers but nothing.
I must say that before to use the factory cable, have the "battery low" red text message and once in any of those multiple press-hold keys sequence attempts (CAN'T REMEMBER WICH ONE) I was able to connect to the phone and windows recongnized via "fastboot device", but couldn't do a flash process due to the low battery state.
Any advise? Thanks in advance.
Click to expand...
Click to collapse
so fastboot isn't working when you are on the screen that says "battery ok" "transfer mode: usb connected"? Your post is a little confusing. It sounds like you are trying to use rsd or something to flash back to stock FW. You can just do all of this manually through fastboot commands.
all you need to do is download the correct FW for your phone at http://sbf.droid-developers.org/ghost_rcica/list.php
unzip the file
put all the contents (not the folder but the contents in the folder) in the same directory that your fastboot.exe is in
run all of these commands http://forum.xda-developers.com/showthread.php?p=46712761&highlight=flash+stock#post46712761
and your done
jayboyyyy said:
so fastboot isn't working when you are on the screen that says "battery ok" "transfer mode: usb connected"? Your post is a little confusing. It sounds like you are trying to use rsd or something to flash back to stock FW. You can just do all of this manually through fastboot commands.
all you need to do is download the correct FW for your phone at http://sbf.droid-developers.org/ghost_rcica/list.php
unzip the file
put all the contents (not the folder but the contents in the folder) in the same directory that your fastboot.exe is in
run all of these commands http://forum.xda-developers.com/showthread.php?p=46712761&highlight=flash+stock#post46712761
and your done
Click to expand...
Click to collapse
Sorry if I was not clear. What I mean is...
Windows does not recognize the phone with the normal usb cable (the one that cames with the phone), says "uknown device".
Now, I try holding Volume Down + Power buttons, then connect the phone via factory cable and screen says "Battery ok, USB connected", but pc (windows 7) still does not recognize the phone, says "unknown device". I already tried to uninstall and reinstall drivers and different computers, but still the same.
There was only one time when the phone (even with low battery pattern) was recognized by windows with the standard usb cable, but can't remenber wich buttons I pressed.
By the way, I read english better than can write it, hope you can understand but most of all, I beg you can help.
Regards.
go_nathan said:
Sorry if I was not clear. What I mean is...
Windows does not recognize the phone with the normal usb cable (the one that cames with the phone), says "uknown device".
Now, I try holding Volume Down + Power buttons, then connect the phone via factory cable and screen says "Battery ok, USB connected", but pc (windows 7) still does not recognize the phone, says "unknown device". I already tried to uninstall and reinstall drivers and different computers, but still the same.
There was only one time when the phone (even with low battery pattern) was recognized by windows with the standard usb cable, but can't remenber wich buttons I pressed.
By the way, I read english better than can write it, hope you can understand but most of all, I beg you can help.
Regards.
Click to expand...
Click to collapse
windows isn't going to recognize it when it is "fastboot mode" which is the mode where is says "usb connected" or whatever. That is where you run fastboot commands from. If you open a command prompt window (in the directory that your fastboot.exe is in) then you can run "fastboot devices" and it will show that the phone is connected. From there you run the fastboot commands to fix your phone.
mmm no, unknown device it's button sequence matter.
jayboyyyy said:
windows isn't going to recognize it when it is "fastboot mode" which is the mode where is says "usb connected" or whatever. That is where you run fastboot commands from. If you open a command prompt window (in the directory that your fastboot.exe is in) then you can run "fastboot devices" and it will show that the phone is connected. From there you run the fastboot commands to fix your phone.
Click to expand...
Click to collapse
In fact fastboot did not work cause windows don't recognized the devices ("fastboot devices" did not list any device). Drivers were installed in the computer correctly but was a matter on how buttons was pressed.
So if this can help any one with the "UNKNOWN DEVICE" status in windows I did it this way, with the device administrator open (only to monitor the status of your device) in windows pc do this:
1.- Factory cable connected to the phone (so the phone did not restart automatically)
2.- Press POWER button until the phone get off. Before release the power button, disconnect factor cable.
3.- Press POWER + VOLUME DOWN for about 5 seconds, then release POWER BUTTON and keep holding VOLUME DOWN until the screens turns on.
4.- Screen says Connect USB Data Cable. Connect Factory cable. Screen says: "Battery Low" "Transfer mode: usb connected"
5.- Now hold VOLUME DOWN + VOLUMEN UP + POWER BUTTON, the phone turns off.
6.- When screen turns off, release VOLUME UP and POWER button. Screen must says "Battery OK" "Transfer mode: USB Connected"
7.- Windows must recognize the phone and install the drivers.
Try:
fastboot devices
...and your phone must be listed. I recommend to do a
fastboot erase cache
I have a downgrade security warning due to a lock bootloader. Once fastboot could connect to the phone, collect the neccesary data with
fastboot oem get_unlock_data
And follow instructions on https: / / motorola-global-portal.custhelp.com/app/standalone/bootloader/unlock-your-device-b
Sometimes you recieve a "your device does not qualify for bootloader unlocking" message, it's only a Device ID string mistake. Be sure to type or paste it correctly. Try again and don't forget to agree the terms below.
I could unlock the bootloader and my phone startup with a previous flash (the one that bricks my phone due to wrong firmware in a locked bootloader phone).
I hope this can help you too. Best regards
So I need help XDA fams. I am currently trying to update my N6 to 5.0.1. The issue i'm having is that my pc wont connect to my N6 while in bootloader. When in bootloader the usb seems to work fine, im assuming, since im getting "transfer mode: usb connected" on the very bottom of the phone screen. But when i adb and check to see if its connected, under "list of devices attached", nothing shows up.
When the N6 is booted up normally it works perfectly fine. I'm able to adb into my phone and it shows up under "list of devices attached".
Ive read around and know windows 8.1 and usb 3.0 drivers might be an issue. So I tried both usb google drivers and the universal naked drivers. I've uninstalled and reinstalled a crap load of times and nothing.
This thing is pissing me off. CAN ANYONE HELP OUT!
Adb is for Android. When you are in the boot loader, you use fastboot.
Try "fastboot devices"
El Daddy said:
Adb is for Android. When you are in the boot loader, you use fastboot.
Try "fastboot devices"
Click to expand...
Click to collapse
Wow lol. I feel stupid. Thanks man. Didnt know that.
But im still having an issue with it being recognized. I go into recovery mode and select the "apply update from adb". When trying to sideload the zip file i keep getting "error: device not found".
Any ideas?
jrforlife said:
Wow lol. I feel stupid. Thanks man. Didnt know that.
But im still having an issue with it being recognized. I go into recovery mode and select the "apply update from adb". When trying to sideload the zip file i keep getting "error: device not found".
Any ideas?
Click to expand...
Click to collapse
Check your device manager in Windows. Make sure it says "ADB Composite Interface" or something similar. If not, you'll have to install the drivers again.
Also, make sure you have the latest ADB package from the SDK.
Hi. I decided to flash my Honor 3c with Cyanogenmod 12.1. My problem is that i need TWRP (now I have CWM) but i can't flash it to my device. I try to do it by SP Flash Tool, but after i connect my turned off device, I get this error:
BROM ERROR : S_BROM_DOWNLOAD_DA_FAIL (0x7D4)
[H/W] Fail to download DA to baseband chip's internal SRAM!
[HINT]: 1. There's an cable communication problem between FlashTool and BootROM. 2. Target might be shutdown unexpectedly or target lost power supply.
[ACTION] 1. Try again. 2. Proceed H/W checking in download cable and target side com port. 3. Monitor if power-drop occured in target side.
Click to expand...
Click to collapse
Where is the problem? I've tried with 2 different cables and 2 different computers
Ceranzuo said:
Hi. I decided to flash my Honor 3c with Cyanogenmod 12.1. My problem is that i need TWRP (now I have CWM) but i can't flash it to my device. I try to do it by SP Flash Tool, but after i connect my turned off device, I get this error:
BROM ERROR : S_BROM_DOWNLOAD_DA_FAIL (0x7D4)
[H/W] Fail to download DA to baseband chip's internal SRAM!
[HINT]: 1. There's an cable communication problem between FlashTool and BootROM. 2. Target might be shutdown unexpectedly or target lost power supply.
[ACTION] 1. Try again. 2. Proceed H/W checking in download cable and target side com port. 3. Monitor if power-drop occured in target side.
Where is the problem? I've tried with 2 different cables and 2 different computers
Click to expand...
Click to collapse
Is your phone in bootloader mode? Hold Vol down+power to enter fastboot mode and then connect your phone to PC.
If you are already doing that or the problem still persists and have an unlocked bootloader(which I am sure you have), try to flash twrp manually.
muradulislam said:
Is your phone in bootloader mode? Hold Vol down+power to enter fastboot mode and then connect your phone to PC.
Click to expand...
Click to collapse
When I do it, my phone just turns on normally.
How can I check if I have unlocked bootloader? I have unlocked it about 1 year ago, but I did full wipe yesterday.
Ceranzuo said:
When I do it, my phone just turns on normally.
How can I check if I have unlocked bootloader? I have unlocked it about 1 year ago, but I did full wipe yesterday.
Click to expand...
Click to collapse
Vol down+power should boot into fastboot. Turn off the phone, hold both until honor logo shows up, let go of power but hold vol down for about 5 sec more.
If still the same, Turn off your phone, connect USB cable to phone, hold Vol down and connect the cable to computer. It should boot into bootloader now.
If it can not boot into bootloader still, the last is to try adb but that is a bit lengthy.
In bootloader mode, it will be written on phone screen in red whether phone is locked, unlocked or relocked.
Wipe does not effect bootloader status so it's still unlocked imo.
muradulislam said:
If still the same, Turn off your phone, connect USB cable to phone, hold Vol down and connect the cable to computer. It should boot into bootloader now.
Click to expand...
Click to collapse
After this, I got this text on my screen:
FASTBOOT&RESCUE MODE
Please connect usb cable to your computer and open hisuite
Click to expand...
Click to collapse
Ceranzuo said:
After this, I got this text on my screen:
FASTBOOT&RESCUE MODE
Please connect usb cable to your computer and open hisuite
Click to expand...
Click to collapse
It did not say anything about phone unlocked in red?
muradulislam said:
It did not say anything about phone unlocked in red?
Click to expand...
Click to collapse
Nope. Maybe I was wrong and I have never unlocked it? I don't remember, but I did something when I was upgrading my phone to Android 4.4.2
Ceranzuo said:
Nope. Maybe I was wrong and I have never unlocked it? I don't remember, but I did something when I was upgrading my phone to Android 4.4.2
Click to expand...
Click to collapse
At least it should say, phone locked. Saying nothing is a phenomenon i never heard before but I usually go for newer versions. May be that's the case.
Anyways use adb to fire this command
Fastboot OEM device-info
To be sure if its locked or not.
To setup adb, download and install latest Android SDK, run the program and only download platform-tools.
Your phone is international variant and it came with locked bootloader, I am sure sp tools unlocked it coz otherwise CWM could not be flashed.
Right click platform-tools folder and select run command prompt window here and type the above command
If the bootloader is unlocked (it will tell you if it is), copy the twrp image to platform-tools folder and rename it to twrp.img and fire this command
Fastboot flash recovery twrp.img
And try to reboot into recovery after disconnecting from pc and simultaneously holding power+ Vol up.
edit: nevermind, i forghot about something...
muradulislam said:
If the bootloader is unlocked (it will tell you if it is), copy the twrp image to platform-tools folder and rename it to twrp.img and fire this command
Fastboot flash recovery twrp.img
Click to expand...
Click to collapse
Should I do this when my phone is switched off?
Ceranzuo said:
Should I do this when my phone is connected to pc or not? Switched off?
Click to expand...
Click to collapse
When your phone is connected to your pc in fastboot mode.
Lemme know how did it go, will reply back in the morning. Hope everything works fine for you.
Sent from my PLK-L01 using XDA Labs
muradulislam said:
When your phone is connected to your pc in fastboot mode.
Sent from my PLK-L01 using XDA Labs
Click to expand...
Click to collapse
Ok, after I typed this command, there appeared this message in window:
<waiting for any device>
Click to expand...
Click to collapse
after this I reboot into recovery mode, but there is still CWM, not TWRP
Ceranzuo said:
Ok, after I typed this command, there appeared this message in window:
<waiting for any device>
after this I reboot into recovery mode, but there is still CWM, not TWRP
Click to expand...
Click to collapse
You dont have your phone drivers installed. Google Huawei USB drivers and install them or use hisuite to install drivers for your phone.
After driver installation, do the same process again.
My bad. I assumed you would have drivers already installed
Sent from my PLK-L01 using XDA Labs
muradulislam said:
You dont have your phone drivers installed. Google Huawei USB drivers and install them or use hisuite to install drivers for your phone.
After driver installation, do the same process again.
My bad. I assumed you would have drivers already installed
Sent from my PLK-L01 using XDA Labs
Click to expand...
Click to collapse
I have already installed many drivers from different sites. I will try with hisuite
Ceranzuo said:
I have already installed many drivers from different sites. I will try with hisuite
Click to expand...
Click to collapse
Hisuite is the best option. Even if that does not work (there is a chance of that), Google Kouch's universal drivers and install those.
May have to manually install dribers if nothing works.
Lemme know how did it go. Will get back to you in the morning if nobody else came along (but someone surely will before that).
Have a nice day/night depending on your time zone
Sent from my PLK-L01 using XDA Labs
---------- Post added at 07:41 PM ---------- Previous post was at 07:31 PM ----------
Lemme get my teacher for you
@DigiGoon
Sent from my PLK-L01 using XDA Labs
I installed Hisuite and connected my phone. Windows have downloaded drivers automatically. And still the same...
But I forgot to tell you that when I connecting my switched off phone, my pc says "USB Device Not Recognized" (or something like that, I dont have english version of windows). Everything is ok when my phone is switched on...
This phone is cursed. I try to give up and stay on my current ROM, so I installed Nova Launcher, but setting it as default doesn't work :/
Thanks for trying to help me anyway.
Ceranzuo said:
I installed Hisuite and connected my phone. Windows have downloaded drivers automatically. And still the same...
But I forgot to tell you that when I connecting my switched off phone, my pc says "USB Device Not Recognized" (or something like that, I dont have english version of windows). Everything is ok when my phone is switched on...
This phone is cursed. I try to give up and stay on my current ROM, so I installed Nova Launcher, but setting it as default doesn't work :/
Thanks for trying to help me anyway.
Click to expand...
Click to collapse
I was awake just for your post. I think I got the problem. You need fastboot drivers imo but I would have to read a bit before I can suggest how to go about it.
Am busy tomorrow but will try to get back to you in the evening (GMT+5 time zone).
Can never be 100% sure but still I am confident, your problem has a solution. Just bear with me a day or two
Sent from my PLK-L01 using XDA Labs
Ceranzuo said:
I installed Hisuite and connected my phone. Windows have downloaded drivers automatically. And still the same...
But I forgot to tell you that when I connecting my switched off phone, my pc says "USB Device Not Recognized" (or something like that, I dont have english version of windows). Everything is ok when my phone is switched on...
This phone is cursed. I try to give up and stay on my current ROM, so I installed Nova Launcher, but setting it as default doesn't work :/
Thanks for trying to help me anyway.
Click to expand...
Click to collapse
Boot into recovery mode, no matter on which recovery are you on, and execute this command:
Code:
adb devices
And see the output, if it says something like:
Code:
**some_number** recovery
then it means there is no problem in the detection of your device by PC, if it does not, then check if the micro USB socket in the device is in good condition.
And I must ask: Are you able to do any operations on device via PC after connecting it?
DigiGoon said:
Boot into recovery mode, no matter on which recovery are you on, and execute this command:
Code:
adb devices
And see the output, if it says something like:
Code:
**some_number** recovery
then it means there is no problem in the detection of your device by PC, if it does not, then check if the micro USB socket in the device is in good condition.
Click to expand...
Click to collapse
I did it and it says some number and recovery
DigiGoon said:
And I must ask: Are you able to do any operations on device via PC after connecting it?
Click to expand...
Click to collapse
In "usb storage media" or something like that? Yes, I do.
Ceranzuo said:
I did it and it says some number and recovery
Click to expand...
Click to collapse
Okay, then it means that there is no problem in the connection. You are using SP Flash tool in which mode?
Sent from my PLK-L01 using Tapatalk