Database Develop

xiaomi mi3 hard brick cold dead?

Lately I was flashing mi3 trough fastboot on w7ulti64bit when something went wrong and now its cold dead.
I have been looking for solution everywhere and as usual xda is my last resort for help with phones, usually I found here what I was looking for but this time it is first time when I have to post new threat.
So basically I found that battery controller had some cold soldier on chip, whole module gives 0v while cell itself 2,8v so I think I fixed it since now whole battery module shows 3.3v and cell itself 3.8v after charging.
But im unable to wake up phone in to fastboot or any other way to reflash it.
When connected to 2000mAh charger there is solid red light, when connected to PC it lit for a second then goes off and PC recognizes mi3 as USB input device and HID compliant device.
I have tried to update drivers for those devises so miflash would recognize it and allow to flash it but without any success.
Any idea what else I could do with it, or how to force flash to flash at least boot sector?

Shamoth said:
Lately I was flashing mi3 trough fastboot on w7ulti64bit when something went wrong and now its cold dead.
I have been looking for solution everywhere and as usual xda is my last resort for help with phones, usually I found here what I was looking for but this time it is first time when I have to post new threat.
So basically I found that battery controller had some cold soldier on chip, whole module gives 0v while cell itself 2,8v so I think I fixed it since now whole battery module shows 3.3v and cell itself 3.8v after charging.
But im unable to wake up phone in to fastboot or any other way to reflash it.
When connected to 2000mAh charger there is solid red light, when connected to PC it lit for a second then goes off and PC recognizes mi3 as USB input device and HID compliant device.
I have tried to update drivers for those devises so miflash would recognize it and allow to flash it but without any success.
Any idea what else I could do with it, or how to force flash to flash at least boot sector?
Click to expand...
Click to collapse
Try mi flash tool

Main problem is that I have tried all 3 miflash I could found 2.11.6 20131108 20140509 and none of them recognizes device and I can't even initiate flashing process ;/

it sounds like a driver issue. just download all the drivers you can find for your phone.

Shamoth said:
Lately I was flashing mi3 trough fastboot on w7ulti64bit when something went wrong and now its cold dead.
I have been looking for solution everywhere and as usual xda is my last resort for help with phones, usually I found here what I was looking for but this time it is first time when I have to post new threat.
So basically I found that battery controller had some cold soldier on chip, whole module gives 0v while cell itself 2,8v so I think I fixed it since now whole battery module shows 3.3v and cell itself 3.8v after charging.
But im unable to wake up phone in to fastboot or any other way to reflash it.
When connected to 2000mAh charger there is solid red light, when connected to PC it lit for a second then goes off and PC recognizes mi3 as USB input device and HID compliant device.
I have tried to update drivers for those devises so miflash would recognize it and allow to flash it but without any success.
Any idea what else I could do with it, or how to force flash to flash at least boot sector?
Click to expand...
Click to collapse
Same problem here, waiting for someone give the solution

if the device is not getting detected in any of the mi flash tools,i feel its a clear sign of driver issues ,

ZenR2 said:
if the device is not getting detected in any of the mi flash tools,i feel its a clear sign of driver issues ,
Click to expand...
Click to collapse
r u following correct procedure for using MI flash tool ?
is ur Phone able to boot to FLash mode ( turn phone off > Press volume + Key then Press Power on - it will show flash mode )
Now Open MI Flash tool > Press Refesh > it will show phone now ( a number will b shown instead of name Xiamo Mi3)
Now Extract Fastboot rom to C Drive ( it should look like this C:\ROM (Location should not cointain space)
Now click Browse > advance > select C:\ROM\Folder\ select bat file

Its not drivers issue since its get detected as QUALCOMM HS-USB QDLoader 9008 or QUALCOMM HS-USB Diagnostic 9006 depending of its state.
In QDLoader it is recognized by miflash as COM20 device and I can upload by miflash or qpst boot image, then it switches to diagnostic that is recognized by some sort of string and I can upload/proceed with rest of rom flashing that includes creating partitions and writing data to them.
Main problem is that when its successfully flashed it is still cold dark, while PC can see it and all partitions like 28 of them...
And I think its related to the fact that qpst reports phone as in download mode.
Any idea how to exit that mode, like in Mi2 that was forced to enter "service" by shortening some pins to put it download mode to flash cold dead ones?

agdag said:
magdag from en.miui.com forum seems to be able to hekp ..or try [email protected] , jason provide paid service
Click to expand...
Click to collapse
You were already looking at it
Kinda wasted a lot of Mine and Yours time and some of my money
If You got any other ideas since that time how to resurrect it just let me know.

Any solution?
Is there any solution to this problem? My phone has been cold brick for 3 days now. Doesnt boot up or charge up. Detected on connecting to PC with a sound, but Shows as Com 10 or 20 on Miflash and thus cannot be flashed.
Cannot boot into fastboot as well.
Anyone anything?

androidy88 said:
Is there any solution to this problem? My phone has been cold brick for 3 days now. Doesnt boot up or charge up. Detected on connecting to PC with a sound, but Shows as Com 10 or 20 on Miflash and thus cannot be flashed.
Cannot boot into fastboot as well.
Anyone anything?
Click to expand...
Click to collapse
You can check the steps I took for recovering from a similar problem here: http://en.miui.com/forum.php?mod=viewthread&tid=22811
If you have any other questions, tag me on your reply and i'll try my best to help.

Phone bricked, need help :c

Hey, Ive tried to install xiaomi.eu rom but didnt realize that i needed the chinese rom and that the global didnt work for this, after ive installed using TWRP the rom, ive rebooted and it just went black, not recovery, not fastboot.
BT was unlocked.
I also see my phone as qualcomm...qloader 9008 when connecting to my pc
Any help?

after having a few heartattacks, ive installed a good Miflsah and a good fastboot rom, and managed to restore my phone to its former glory
no need for further help, but i have a few advices
dont be stupid like me, and listen to directions like theyre the word of god, when they say change from chinese rom to a non official rom, YOU NEED CHINESE, global wont work
and if you're having problems with miflash giving errors, try a bunch of downloads, old, new, everything.

Hi, yet another brick here!
I had an AOSP ROM but I had problems with it. I entered TWRP, downloaded a MIUI official ROM for recovery, wiped the phone from TWRP and decrypting it (there was an option for that). Then I did try to flash the ROM and... black screen. No signs of life.
However, when I connect it to the computer it detects it as the famous Qualcom xxx 9008 (COM10) device. But fastboot is not working, when I type "fastboot devices" it doesn't return anything. ADB doesn't recognize the phone either. Everywhere I saw that I should use MiFlash to recover it, but I took a look at the scripts and are using fastboot to perform the process. But since fastboot doesn't recognize the device, it won't work. I get stuck all the time at "Failed to receive the hello packet".
Fastboot doesn't detect my phone either on Linux or Windows. I tried Linux, virtual Windows 10 (x64) and at last I'm trying on a Windows 10 (x64) computer (no virtualization). No matter what I do, it always stays at the same point. I also used several MiFlash versions (from old builds from last year to the most up-to-date version of XiaomiMiFlash). But since fastboot is not detecting the phone I think there's no point in switching MiFlash versions.
So... what can I do? Should I use the pin short-circuit /deepflash cable method? As of I understand, that is what you use to get into EDL, but if my device is showing 9008 in device manager doesn't it mean that I'm already in EDL? I'm not really sure because all the threads I saw in several forums are a bit messy.
I'll appreciate any help. I don't have phone since 3 days ago and I can survive without it but I need it for my work.
Thank you in advance!
EDIT:
Forgot to say, if I try to power off and power on it doesn't do anything BUT when I plug and unplug from the charger it does show a battery icon with the charged percentage. That's the only sign of life from the phone, aside from being recognized as a 9008 device, but that actually happens when I try to (blindly) get in fastboot mode.

FIXED!!! After four hours testing out several options I found the solution: Open up the phone, unplug the battery cable, plug it again, and voilà. The phone automatically got recognized (again) as Qualcomm 9008 device but this time the flash went on flawlessly. It took less than 5 minutes, once succeeded I powered on the device and it ran into MIUI 8 in less than 5 minutes.
So, if you find issues with the command "fastboot devices", unplug the battery and try it again before troubling yourself with deepcables or shortcircuits ;-D
NOTE: Taking out the back cover is very easy, search on youtube, I bought the thing you need for 1$ at the store next to my home (sorry I don't know what it's called).

I Messed Up My phone fastboot not working!!!!!

Hello Everyone, so 2 days ago i hard bricked my MI 8 with flashing an eu rom over global mi 8 rom with twrp then when i rebooted the phone it stuck at mi logo so i tried to goto recovery mode again but nothing happens when i press power + volume up its just mi logo and i tried to go to fastboot mode but not luck i get a black screen....................so i decided to connect it to a computer but no signs of anything(not detected).....so i searched google a little and i found a solution wich envolved disassembling the phone the method called EDL method with test point,,,,,,,so i opened my phone with my friends and tried to do the test points,,,when i joined the testpoints and then connecting the phone to pc.....nothing happened.....it should detect the phone but nothing happens.....please help guys!!!

Keep trying with edl, maybe it's a driver issue, but if you can't get it to edl I don't think you can recover your phone ?

mi_guel said:
Keep trying with edl, maybe it's a driver issue, but if you can't get it to edl I don't think you can recover your phone
Click to expand...
Click to collapse
I have been trying....but no luck till now:crying::crying::crying:

alandxaled said:
I have been trying....but no luck till now:crying::crying::crying:
Click to expand...
Click to collapse
You need to use QPST.
Also you didn't need to open the phone, that step is outdated.
Go ahead and read up on installing all of the needed drivers and as long as your phone is linked to you. That is you have the phone registered to your MiCloud account this issue should be fixable.
I dont have a lot of time today or tomorrow. but I am willing to try and help you figure this issue out.

tsongming said:
You need to use QPST.
Also you didn't need to open the phone, that step is outdated.
Go ahead and read up on installing all of the needed drivers and as long as your phone is linked to you. That is you have the phone registered to your MiCloud account this issue should be fixable.
I dont have a lot of time today or tomorrow. but I am willing to try and help you figure this issue out.
Click to expand...
Click to collapse
I installed the drivers...but the main problem is that when i connect it to the pc ....the pc did not recognize the phone not even in device manager

alandxaled said:
I installed the drivers...but the main problem is that when i connect it to the pc ....the pc did not recognize the phone not even in device manager
Click to expand...
Click to collapse
This could be an issue with the PC...happens all the time.
If the battery is not completely dead, or if the usb port is not completely fried you should be able to at least see the port.
It's also possible that you are not in EDL.
Simply Flashing the EU rom over Global will not brick your phone, I have done that myself many times. Was your bootloader unlocked? If not then you will probably need to take it to a Xiaomi Service center.
Does the phone mac any vibrations when pressing and holding both the volume up and down ( at same time along with the power button?
Have you tried alternate usb c cables?
If you have a newer computer with usb 3.0 ports you will need to use a Usb hub., which will downgrade the connection to usb 2?
Is ADB Installed on this computer along with generic android drivers?
is the computer up to date?
Have you tried an alternate user and are you using the admin account?
If you have a device that uses linux, see if Linux will see the phone.
If you have tried everything, and you still you see the phone, and the phone has not been exposed to an extreme amount of force or to water. It may be that your usb card in the phone is fried or there is a short in the internal usb flex cable. ( It's the wire that connects the usb card to the motherboard.
You can Google the steps to make your own deep flash cable, that would help rule things out much faster.
I am going to sleep now. Good Luck.

@tsongming Do you know why he bricked his phone? I mean he just flashed .eu.

tsongming said:
This could be an issue with the PC...happens all the time.
If the battery is not completely dead, or if the usb port is not completely fried you should be able to at least see the port.
It's also possible that you are not in EDL.
Simply Flashing the EU rom over Global will not brick your phone, I have done that myself many times. Was your bootloader unlocked? If not then you will probably need to take it to a Xiaomi Service center.
Does the phone mac any vibrations when pressing and holding both the volume up and down ( at same time along with the power button?
Have you tried alternate usb c cables?
If you have a newer computer with usb 3.0 ports you will need to use a Usb hub., which will downgrade the connection to usb 2?
Is ADB Installed on this computer along with generic android drivers?
is the computer up to date?
Have you tried an alternate user and are you using the admin account?
If you have a device that uses linux, see if Linux will see the phone.
If you have tried everything, and you still you see the phone, and the phone has not been exposed to an extreme amount of force or to water. It may be that your usb card in the phone is fried or there is a short in the internal usb flex cable. ( It's the wire that connects the usb card to the motherboard.
You can Google the steps to make your own deep flash cable, that would help rule things out much faster.
I am going to sleep now. Good Luck.
Click to expand...
Click to collapse
1-My Bootloader was unlocked yes!
2-i flashed eu rom over evolution rom(Custom rom)
3-Yes It Does Vibrate
4-Yes I Have Tried Other Usb Cables
5-yes, adb installed with generic usb driver
6-yes its updated and i tried mutliple ports
7-i haven't tried linux
8-and i dont think that my usb card is fried because before that it was working
And Another Thing That Might Have A connection with the problem"Before i flashed eu rom over custom rom the unlocked text was shown in the display when booting with mi logo but now that text has gone"

alandxaled said:
1-My Bootloader was unlocked yes!
2-i flashed eu rom over evolution rom(Custom rom)
3-Yes It Does Vibrate
4-Yes I Have Tried Other Usb Cables
5-yes, adb installed with generic usb driver
6-yes its updated and i tried mutliple ports
7-i haven't tried linux
8-and i dont think that my usb card is fried because before that it was working
And Another Thing That Might Have A connection with the problem"Before i flashed eu rom over custom rom the unlocked text was shown in the display when booting with mi logo but now that text has gone"
Click to expand...
Click to collapse
The EU rom does not lock the bootloader, the developers actually removed the bit of code that will allow MiFlash to lock the bootloader. Whenever leaving or returning to Miui, storage must be formatted.
The problem with these custom roms for the Mi8 is that These mi8 developers do not work together ( like most do, on other threads) These developers are always fighting and arguing and accusing each other of stealing their code, while they do it themselves and they all have their own way of doing things. Ideally every rom should use the same device tree, firmware and vendor...The basics! But no, everyone does things differently.
I would suspect that your phone bricked due to firmware encryption or just corruption. Even though it seems that it can't be fixed, you will surely be able to fix it eventually.
Many people were eventually able to solve this exact issue in the past with success. so start with the basics., and dont give up when or if it fails, just try again on a different device, and be sure to disable Windows defender. Because it's possible you could have your computer setup in a way that it will make this process harder to resolve, temporarily disable the antivirus and firewall etc.
Download the All in One tool: https://forum.xda-developers.com/mi-8/development/tool-tool-one-driverstwrpfactory-t3895807 If it gets flagged, and completely disabled. then your computer is helping contribute to this issue.
If you can successfully install and open the tool, use it to update adb and android drivers and to apply system wide adb access. Next manually setup the phone , even if it claims to not see a fastboot device. and attempted to remove encryption. if this fails find a Linux machine to complete these tasks.
See if you can leave EDL, by pressing and holding the power and volume down. >>>>> Even if you dont see the fastboot screen the computer may see the phone in fastboot.
I definitely believe that you will have a easier path to getting this issue resolved sooner by using linux. If you can "format" ( not wipe) user data, install TWRP and root the rest will obviously be easy.
---------- Post added at 06:23 PM ---------- Previous post was at 06:22 PM ----------
Boiisxu said:
@tsongming Do you know why he bricked his phone? I mean he just flashed .eu.
Click to expand...
Click to collapse
He didn't format user data, or the file was somehow corrupted

Unlocking Tool gets stuck at either 50 or 99 %. "Can't unlock, Couldn't get info"

Unlocking Tool gets stuck at either 50 or 99 %. "Can't unlock, Couldn't get info"
So, I've tried to unlock my phone for 2 months now without any success. I've done basically everything I could think of, but the same problem persists. The problem is that it gets stuck at either 50 or 99%; followed by a message that says: "Can't unlock, Couldn't get info" Also, I've made sure to wait at least 10 days after I've reconnected my account to retry but the unlock tool won't even show how long I have left.
What I've tried:
- Changing USB ports, Gen 2, 3 and 3.1.
- Using a USB HUB
- Reinstalling ADB drivers
- Resetting my PC
- Trying a different PC
- Reinstalling Qualcomm Fastboot drivers
- Different cable
- Resetted my MI account
- Deleted and created a new MI account
- Used another sim card and phone number
I'm quite desperate as unlocking it is somewhat important for me. As a poor student, I can't really afford to sell it and buy another phone to unlock either.
I'm not sure what's going wrong. I've unlocked many (well, 5) android phones in the past and never had any major issues like this.
Any tips and ideas would be appreciated.

I had this issue before , what I did to solve it is :
1)Use Intel system (AMD won't ever work) and enable usb debugging
2)Don't plug in your phone yet, open Mi Unlock and log in till You reach searching for phone step
3)Open Mi Unlock settings and click install driver
4)Make sure your phone is turned on normally and plug it in through USB 2
5)You will see message on pc telling u drivers are installed now check the phone to see (USB settings) click File Transfer ,now Mi tool should say plug your phone in boot loader mode
6)Turn off your phone and while it is turning off unplug the USB , now boot into fastboot and then plug ur phone in USB 3 port
This is tricky and buggy I got it first time and reached the message after 100% verifying but it said I still had to wait some time so when I tried to unlock it after the time passed I had to repeat these steps couple of times to work so be patient
The problem is mi tool needs both ADB and Fastboot drivers to be working but most of the time its only Fastboot driver due to the phone shutting down so its buggy as hell
https://prnt.sc/rbmvam
These are the drivers that should be both working so check them while repeating the steps if you got them both working you are good to go

The first time i tried to unlock my bootloader, unlock tool would be stuck at connecting to the device and couldn't see it.
No matter what i did it would never see it.
So i decided to try xiaomi tool v2 (not endorsed by Xiaomi). I also used a usb hub that i plugged to my laptop usb c and finally my device could be unlocked.

Did you buy the phone used or new?
Does it have a Global ROM, or it is a Global Version or CN?

[Solved!] [OnePlus 8 Pro] Problems with OOS 11.0.4.4.IN11AA

I have a OnePlus 8 Pro running Oxygen OS 11.0.4.4.IN11AA. Upon installing Magisk, I can no longer turn Wifi on. I have tried restarting, clearing the cache from recovery, resetting network settings, basically all the things the "wifi wont turn on help pls" guides say to do. Mobile data and bluetooth work absolutely fine, so what's going on?
Sound is also non-functional. Even after plugging in earphones (which worked with this phone previously) nothing comes out, and the phone doesn't even seem to recognize them. I also noticed that after a reboot the volume controls are set back to the defaults.
Additionally, the system is very slow to start up and the screen stays black until after the unlock prompt (which displays over the black screen) and then the wallpaper and everything else loads. (after which the device is responsive as normal)
These problems occurred even without installing any modules or otherwise modifying the device. I'm using the latest version of Magisk, 22.0 (22000).
I originally tried to make a GitHub issue, but it was closed by the bot since I didn't follow the template GitHub never showed me. Also, us non-canary users experience issues too. [mini-rant over]
Sorry if this is a duplicate, the search system appears to be malfunctioning since the updates.
The Fix!
Looks like I'm solving all my problems today. I had a hunch that the culprit was the boot.img which I downloaded--it was corrupt. So I went to OnePlus' site and downloaded the OTA package, extracted the boot.img from that, and flashed it through fastboot. When I rebooted, I was greeted with the beautiful almost old-IOS charging sound, and Wifi!! That boot was quite speedy too!

Hi could you explain how did you reboot your phone i have totally same problem...i tried msm download tool but i cant get my device to show there....could you please tell me how did you put OTA package into phone ? thx
FIXED!
in the end I was able to use MSM Download tool....i just had to manually download Qualcomm drivers so that my phone can be recognized. After that MSM worked and rebooted my phone totally clean. Gosh not gonna root for a while now XD
PS: More fun is that my Windows PC wasn't connected to internet so i had to download everything on my macbook and through USB stick I was bringing all app to Windows.....longest 6 hours of my life

Jaywinik said:
Hi could you explain how did you reboot your phone i have totally same problem...i tried msm download tool but i cant get my device to show there....could you please tell me how did you put OTA package into phone ? thx
Click to expand...
Click to collapse
From fastboot, use the volume keys to select Power Off and then press the power button once. Make sure the phone is unplugged while doing this. Then, with the MSM tool ready on your computer, hold down both buttons on your phone and plug in the cable from the phone to the computer. It should automatically boot into EDL mode, and MSM should say Connected.

My
Jaywinik said:
Hi could you explain how did you reboot your phone i have totally same problem...i tried msm download tool but i cant get my device to show there....could you please tell me how did you put OTA package into phone ? thx
FIXED!
in the end I was able to use MSM Download tool....i just had to manually download Qualcomm drivers so that my phone can be recognized. After that MSM worked and rebooted my phone totally clean. Gosh not gonna root for a while now XD
PS: More fun is that my Windows PC wasn't connected to internet so i had to download everything on my macbook and through USB stick I was bringing all app to Windows.....longest 6 hours of my life
Click to expand...
Click to collapse
When I had to do this I didn't connect the device to the network since I don't trust Windows 10 not to open a billion ports up and use my infrastructure for Microsoft's business. Copying to and from a crappy 2.0 drive sucks!