Hi,
I just got my Xperia 1 II and a wallet case to it. Skimblocker XL Wallet by Coverin. It has a magnetically removable shell which the phone is mounted in. The problem is that as soon as I attach the magnetic shell to the case the screen go off and can't be put on. I can only use the phone if I detach it from the case which in my opinion is completely useless!
I've been looking into the settings but haven't find anything to prevent this.
Any ideas?
Related
Has anyone been able to/willing to figure out a way to disable the whole screen-off by magnet thing? I've been using a magnet mount in my car, and everything works great except that if placed just a bit off, the screen will turn off. Turning the screen on doesn't help because it will turn right back off again as soon as you swipe away the lock screen. As soon as I remove my phone from the holder (or even just slide it up/down a bit) it will stop doing it. I can't really move the plate the magnet attaches to, because then it would interfere with wireless charging. I've seen solutions for other devices, but not the N6. Thanks.
following! i have the same issue with my magicmount.
melficeapollo said:
following! i have the same issue with my magicmount.
Click to expand...
Click to collapse
where have you put your "plate" on your phone? do you use wireless charging at all?
I don't use wireless charging. It was for a magnetic mount in my car. I had my plate attached to the spigen slim case and I placed it about an inch below the Motorola logo, my phone kept locking and wouldn't unlock as long as I had the plate there and attached to the magnetic mount. I ended up having to move it up and cover about half the Motorola logo and it works fine, but I find that aesthetically unpleasant.
Therefore I'm hoping someone has a solution so i can lower the plate to where it was before.
Would also like a fix for this. Use a magnetic phone holder too. If I get it in a sweet spot then I'm OK but any movement or mount it just off screen is off and can't get it back on. Like a tasker to disable this would be perfect!
basicreece said:
Would also like a fix for this. Use a magnetic phone holder too. . . .
Click to expand...
Click to collapse
Till now I could not find a software solution to disable the magnet sensor.
In my car there is a strong neodymium magnet. Fixed with double sided tape. Diameter about 20 mm.
On the back of my N6 is a hard case with a small metal piece fixed on the outside with superglue.
When the metal is mounted on the lower part (about 1 cm below the M-logo) the magnet sensor is not activated
When there is metal on the back, wireless charging is not possible. The metal will be very hot and may cause damage.
I have the Logitech [+] drive magnetic mount in my truck. When I attach the Nexus 6 to the mount, the screen turns off. If I try to turn the screen on while the phone is magnetically attached to the mount, the screen will immediately turn off. As soon as I remove the phone from the mount, the screen will come on. Does anybody know if there is a setting that controls this behavior or any kind of work around (i.e. Tasker, etc) so the screen will stay on when attached to the mount? I would like to use the phone for navigation, but that is obviously out of the question unless I use a non-magnetic mount or just leave the phone loose in the console, which neither option is preferable to the ease of the magnetic mount. Any help is appreciated.
Thanks
No solutions so far at the moment. But keep an eye on this thread http://forum.xda-developers.com/nexus-6/general/magnet-screen-off-t2968380
where (on the back of the phone) do you have the metal plate placed?
above or below the motorola M? or over top of it?
also, does the metal plate lay flat on the back? or are you using it along with a case?
Is there any way to disable the magnetic sensor on the N6? I have a smart cover that keeps constantly turning the screen on in my pocket and it's killing my battery. It is a very nice luxury case and I don't want to damage it or replace with another cover. I tried finding an app that would do it but no luck. Any help would be greatly appreciated!
bobprobert said:
Is there any way to disable the magnetic sensor on the N6? I have a smart cover that keeps constantly turning the screen on in my pocket and it's killing my battery. It is a very nice luxury case and I don't want to damage it or replace with another cover. I tried finding an app that would do it but no luck. Any help would be greatly appreciated!
Click to expand...
Click to collapse
Dont think there is a way to disable it yet.
Although i read elsewhere its located in /sys/module/ and adding a '0' or 'false' to the value will disable. Issue is still not located the magnetic sensor, older devices it was in /sys/module/lid/parameters/lid_enabled.
But no luck on N6 yet
has anyone had any luck using an app to accomplish this?
bobprobert said:
has anyone had any luck using an app to accomplish this?
Click to expand...
Click to collapse
Found nothing to disable the magnet sensor.
Installed Xposed and a MagnetOff app. But it did not disable the magnet sensor.
Because I cannot disable that feature, I decided to use it.
On the outside of my belt case I attached a small magnet (glue) and now my screen is always off when the N6 is in the case.
When I take the N6 out of the case the screen turns on. No need for pressing a button.
NLBeev said:
Found nothing to disable the magnet sensor.
Installed Xposed and a MagnetOff app. But it did not disable the magnet sensor.
Because I cannot disable that feature, I decided to use it.
On the outside of my belt case I attached a small magnet (glue) and now my screen is always off when the N6 is in the case.
When I take the N6 out of the case the screen turns on. No need for pressing a button.
Click to expand...
Click to collapse
you sure the screen is always off when it's in your case? like the OP, I found that my screen would periodically come on when using a flip case that has the auto on feature (while closed).
PhilDX said:
you sure the screen is always off when it's in your case? like the OP, I found that my screen would periodically come on when using a flip case that has the auto on feature (while closed).
Click to expand...
Click to collapse
When de magnet is close to the circle with the Motorola logo the screen is switched off.
I am using a flat neodymium magnet with a diamater of 10 mm.
Because the case is partly open at the top, I can see that the screen is really off when the N6 is in the belt case.
http://www.ebay.com/itm/Cool-CowBoy...t=LH_DefaultDomain_0&var=&hash=item4d2493c910
When you are unsure if the screens will be turned off when the N6 is in the case, use a stronger magnet.
I mounted with glue a magnet at the outside and put a second one on the inside.
So I am using two small magnets.
any developer willing to dig into this issue to try to find a solution?
Hello All,
I've recently acquired a case for my Note 8. I'm not much of a case fan but I figured I'll take the plunge as the phone is too precious. I got a normal (fake) leather book type case.
Thing is, every time the phone is in the case, it for some reason acts like the pen has been taken out. When I pop it in, the screen off memo appears (Despite S Pen being still inside) and the Air Command icon stays on screen (I've now disabled that in the settings). Yet whenever the phone is out of the case, I have no issues with the S Pen.
When I put the phone into the case, I insert the bottom half in first, when the phone is at a fairly acute angle of like 20 degrees, screen off memo appears and the phone thinks the S Pen has been engaged for the duration of the phone being the case. This also happens if I insert the phone top first as well. Yet when I lift the phone back out (This is when the screen off memo appears when I'm putting the phone in), the screen off memo screen just goes off like I just put the pen back in. When the phone is in the case, I can't use the screen off memo either. Quite frustrating.
Is the phone case itself to blame ?
Professor1991 said:
Hello All,
I've recently acquired a case for my Note 8. I'm not much of a case fan but I figured I'll take the plunge as the phone is too precious. I got a normal (fake) leather book type case.
Thing is, every time the phone is in the case, it for some reason acts like the pen has been taken out. When I pop it in, the screen off memo appears (Despite S Pen being still inside) and the Air Command icon stays on screen (I've now disabled that in the settings). Yet whenever the phone is out of the case, I have no issues with the S Pen.
When I put the phone into the case, I insert the bottom half in first, when the phone is at a fairly acute angle of like 20 degrees, screen off memo appears and the phone thinks the S Pen has been engaged for the duration of the phone being the case. This also happens if I insert the phone top first as well. Yet when I lift the phone back out (This is when the screen off memo appears when I'm putting the phone in), the screen off memo screen just goes off like I just put the pen back in. When the phone is in the case, I can't use the screen off memo either. Quite frustrating.
Is the phone case itself to blame ?
Click to expand...
Click to collapse
Could b the magnets of the casing screwing around w phone sensors
Sent from my SM-N950F using Tapatalk
I got rid of the cases with magnets. The fake ones are worse. Try using your SPEN and run lines across the screen in snote or any other writint app.
Sent from my SM-N950F using Tapatalk
I was thinking of getting a mount that allows me to mount when in dual screen. Maybe even use while in dual screen.
One possibility was a mount for a tablet.
Maybe this: https://www.amazon.com/gp/product/B00585CLR2/ref=ox_sc_act_title_1?smid=ATVPDKIKX0DER&psc=1
I haven't found a mount for a tablet that also has wireless charging.
It is useful to be able to use dual screen, but my main reason is that I don't what to take the phone in an out of the case because of reports of charging port failing.
UPDATE: I did get the mount above, and it works very well. I can mount with the dual screen (or without), while screen is open, both in landscape and portrait. The phone sits quite sturdy. And, no problem to connect power. It is nice to have navigation on one screen, and music/podcast on the other.
ghostwheel said:
I was thinking of getting a mount that allows me to mount when in dual screen. Maybe even use while in dual screen.
One possibility was a mount for a tablet.
Maybe this: https://www.amazon.com/gp/product/B00585CLR2/ref=ox_sc_act_title_1?smid=ATVPDKIKX0DER&psc=1
I haven't found a mount for a tablet that also has wireless charging.
It is useful to be able to use dual screen, but my main reason is that I don't what to take the phone in an out of the case because of reports of charging port failing.
Click to expand...
Click to collapse
https://www.amazon.com/dp/B07L2XTPZ4/ref=cm_sw_r_cp_apa_glc_fabc_Q5RJDV965NMKC8ZJ5ZGS?_encoding=UTF8&psc=1
This is the one I have. I put the main phone in it and open the dual to the side. Works fine.
You are right. When the dual screen is 180 degrees open, there's still enough room to latch on. Worked today with my regular phone holder. Not amazingly stable, though.
Mine is pretty tight. So not much different for me.
would anyone try a velcro mount??
so the back of the dual screen case would have a permanent velcro thin pad silicone on, glued on, the more expensive baby version of the velcro strips, that is super soft, the hooks side will be on the car mount.
this way both screens can be on, like maps wide view.
not sure how many strips will be safe enough and probably would look super ugly but functional
Nah. My existing mount works fine
any chance you can show pics of the phone grip from the side or back? im just thinking with all the glass, one bump and drop and its cracks everywhere
Using my regular mount, phone isn't very secure. Works in a pinch.
The mount mentioned above works very well.
The one I bought on Amazon isn't available any more, but it was like the one below. It grips the side and still lets the screen open like others said. not great, but OK. Only came out once. Not sure if I can get a photo of it sitting in the case, but i'll see.
Amazon.com: Windshield Car Phone Mount - OQTIQ Upgraded 13-Inches Long Arm Gooseneck Cell Phone Holder for Car Truck Dashboard Phone Holder with Strong Suction Cup, Compatible with iPhone Samsung Galaxy LG
Amazon.com: Windshield Car Phone Mount - OQTIQ Upgraded 13-Inches Long Arm Gooseneck Cell Phone Holder for Car Truck Dashboard Phone Holder with Strong Suction Cup, Compatible with iPhone Samsung Galaxy LG
smile.amazon.com