After lock bootload i got bootloop and Show :
Red state "restart every 5 second"
can't go to recovey or turn off
it only restart
I tried SP flash tool but got error as soon as click download. And error is ;
ERROR: STATUS_BROM_CMD_SEND_DA_FAIL_(OxC0060003).
another thing i noticed is when phone is usb connected i keep hearing sound for usb conenct and disconnect every 10 seconds.
looks like phone is not connecting well to PC.
I installed all posisble drivers for win 10. I installed mediatek driver, Oppo, Realme drivers etc
Please please please HELP Meee
Hint: Replace in this thread's title "Help Pleaseeeeee" by "How to fix bootloop"
thankx2u said:
After lock bootload i got bootloop and Show :
Red state "restart every 5 second"
can't go to recovey or turn off
it only restart
I tried SP flash tool but got error as soon as click download. And error is ;
ERROR: STATUS_BROM_CMD_SEND_DA_FAIL_(OxC0060003).
another thing i noticed is when phone is usb connected i keep hearing sound for usb conenct and disconnect every 10 seconds.
looks like phone is not connecting well to PC.
I installed all posisble drivers for win 10. I installed mediatek driver, Oppo, Realme drivers etc
Please please please HELP Meee
Click to expand...
Click to collapse
Try to format your bootloader using sp flash tool and reflssh it
Related
Hello,
I have some problems trying to flash my XZ. I'm using Xperia Flashing Tool 0.9.10.2 beta6 on Windows 8 x64 and whenever I try to flash my XZ flashing tool "gets stuck at "Device connected in flash mode" message after which it gets reconnected and if I try again same thing will happen.
So my question is, am I doing something wrong and if so, please advise.
Bluffer said:
Hello,
I have some problems trying to flash my XZ. I'm using Xperia Flashing Tool 0.9.10.2 beta6 on Windows 8 x64 and whenever I try to flash my XZ flashing tool "gets stuck at "Device connected in flash mode" message after which it gets reconnected and if I try again same thing will happen.
So my question is, am I doing something wrong and if so, please advise.
Click to expand...
Click to collapse
have you correctly installed the drivers for it, connect phone in flashmode and does windows drivers load, also in flashtool go to devices>conected devices and what does it say
Maddhouse said:
have you correctly installed the drivers for it, connect phone in flashmode and does windows drivers load, also in flashtool go to devices>conected devices and what does it say
Click to expand...
Click to collapse
I think drivers are installed fine. Screenshot is below.
no doesnt look it, under ADB devices there is no device, Reinstall drivers and try again. Try the way in my sig for win 8
Unfortunately same thing happens - check screenshot below.
Bluffer said:
Unfortunately same thing happens - check screenshot below.
Click to expand...
Click to collapse
thats better you now have a ADB device installed, you should now be able to put your phone into flashmode
power off your phone with usb diconnected, hold vol down and reconnect turned off phone to usb and you should now get green led and flashtool will say device connected in flashmode but you only have about a min in flashmode before phone reboots
Thank you for your help and effort but even now it keeps disconnecting device. I don't know where the problem is, maybe I'm not doing something as I should.
This is the procedure I was trying:
1) I select Flash device in flash tool
2) I select Flashmode mode
3) I choose which firmware to flash and click Flash so flash tool can start it's magic
4) When flash tool shows message that I can remove my device from USB and turn it off I do so
5) I also press volume down and reconnect the device with the PC.
6) Problem happens here
what about if flashtool isnt ready to flash file, does flashtool pick it up (4 and 5)
it will say device connected in flashmode with green led
Yeah, it does pick it up and displays a message "Device connected in flash mode" and after awhile "Device disconnected".
Bluffer said:
Yeah, it does pick it up and displays a message "Device connected in flash mode" and after awhile "Device disconnected".
Click to expand...
Click to collapse
good yer i think its about a min, now try and download another FTF file
part 1
part 2
that works i have got loads of people to flash that
edit: i made it so its self extract version then there is a FTF file for flashtool
As you suggested the problem was in faulty FTF. It's working like a charm now!
Thank you once again!
Bluffer said:
As you suggested the problem was in faulty FTF. It's working like a charm now!
Thank you once again!
Click to expand...
Click to collapse
Good Good, What wasnt helping was you didnt have drivers installed aswell, now you just have to root and your sorted :highfive:
hey i m having same with my x8 after i accidently kept stock rom for nalf kernal... nw i m nt able to open cmw in phone...plz help..
Hi guys, got a slight problem with entering fastboot mode. I hold the volume-up key and connect me USB cable but rather than getting the noise verifying it's been connected ok, I get that dull sound it makes when it hasn't worked. It won't even let me install the drivers and in device manager it comes up as "S1boot Fastboot" for a few seconds before then going into battery charging mode. I downloaded the Android SDK latest and replaced the USB driver INF file with the one sony give you but it didn't work so reversed back to the other driver the SDK manager installs and that didn't work either.
I've been through the tutorials and even tried to update the driver in device manager in the few seconds it stays there but that didn't work either! USB debugging is enabled too!
Please help, I'm not a noob and have done fastboot booting before and yes for those who may ask have already checked to make sure the bootloader can be unlocked and yes it can also the phone is NOT branded and is unlocked to all networks.
Any help will be appreciated, thanks!
Dave.
Are you on Windows 8? Using USB 3.0?
"As your flesh bears the sigil....your name is that....of a recusant."
First be sure you're using a 2.0 usb port, if this is ok maybe it's a windows 8 driver problem, so you should try this http://forum.xda-developers.com/showthread.php?t=2170114. It works for me
For also fastboot and flashmode come for 5 Sec. So Make sure you prepare the file and attach the device to fastboot or flashmode when it is asked.
Still problems
I'm still working on a 2012 laptop with Windows 7 Premium installed. It's fully up to date and all the drivers are installed properly I just don't get it, I've tried everything and it's still making the noise as if it won't connect. I don't know what to do to be honest. Also yes it is USB 2.0.
darkdemon32 said:
I'm still working on a 2012 laptop with Windows 7 Premium installed. It's fully up to date and all the drivers are installed properly I just don't get it, I've tried everything and it's still making the noise as if it won't connect. I don't know what to do to be honest. Also yes it is USB 2.0.
Click to expand...
Click to collapse
Hmm...how many USB ports are being used when you're flashing the phone?
"你看到了没? 爱让我流胆怯的泪..."
"Have you seen it? Love has made me cry cowardly tears..."
Fastboot with Xperia XP
I have the same problem, can't get it to fastboot mode.
Tried the Windows 8 zith USB 2, and also on XP machine where I was succesfully used it for a Xperia U.
Dump Windows..
Opensource rules!!! I switch on a VM with Windows only when I need Photohshop. Otw, Ubuntu and openSUSE FTW!!
sarkar1990 said:
Dump Windows..
Opensource rules!!! I switch on a VM with Windows only when I need Photohshop. Otw, Ubuntu and openSUSE FTW!!
Click to expand...
Click to collapse
Opensource forever)))
Sent from my ME371MG using xda app-developers app
same problem...
m having same kind of problem i was trying to flash boot img from cm 11 but fast boot isnt recognizing my device any more.my sp is rooted bootloader unlocked.fast boot was recognizing it yesterday.please tell me what to do
What I did was use a Windows XP machine.
Couldn't get it to work on my Windows 7/8, because of the restrictions in driver signatures.
Sent from my C5303 using Tapatalk
fastboot
darkdemon32 said:
Hi guys, got a slight problem with entering fastboot mode. I hold the volume-up key and connect me USB cable but rather than getting the noise verifying it's been connected ok, I get that dull sound it makes when it hasn't worked. It won't even let me install the drivers and in device manager it comes up as "S1boot Fastboot" for a few seconds before then going into battery charging mode. .
Click to expand...
Click to collapse
I have a similar problem. the power light lights up blue then passes into the phone starts loading mode
Sorry for bad English
The updated version (09.14) don't work properly. It doesn't enable me to go to Flashmode. Uninstalled and used the previous version and it worked as it should, no issues entering Flashmode.
i might have actually found the solution. im on the 4.3fw build version 12.1.a.1.201... in my case, my pc will automatically install the drivers for mass storage giving me no chance to update the driver to the one from sony.
you need to do step 9. and 10. if you havent done so from http://unlockbootloader.sonymobile.com/instructions
what i did was allow developer settings and allow debugging via usb.
plug in and attempt to go in to fastboot and obviously it'll fail.
go to device manager. (control panel->hardware and sound->device manager) quickly scroll down go to other devices. you will see s1fastboot (or something like that) if you're quick enough, if not, in my case, the phone will go in to charging mode.
what i did was to disable xperia sp mass storage from disk drives category too.
right click on it and select update driver software and you will select the file you've unzipped (following step 9 and 10 sony's instructions).
after it has finished updating, unplug your usb and attempt to enter fastboot, it should work.
PS: im no expert, this solution might be out there somewhere already or it could just be a great coincidence. some of these steps might not be useful even.
Had this problem and found a funny solution: I switched my cable and the port I was using. Both Ubuntu and Windoze 7 failed on both fastboot and flash mode, even though in both the phone would charge. I grabbed a spare micro USB cable and plugged it into the front of the PC; voila. Now the phone is rooted and running the latest CM.
Need a final solution for this problem
I don't know what to do!!! The problem is this, very similar to the others mentioned above,: When i conect my xperia sp to fastboot mode, pressing volume up while plugging in usb cable, the phone led turns to blue for few seconds and than it just turns to red showing on the screen the battery image( normal charging mode)...... I' m using windows xp and a rooted xperia sp whit cm11 (for locked bootloader obviously). Just two last things:
the phone can be unlocked( I checked it) and fastboot worked the same as now with stock xperia sp firmware.
Please i need a final and a certain solution for this problem!!!
i'll be very thankful to anyone who give me a hand!!!!
TheTras said:
I don't know what to do!!! The problem is this, very similar to the others mentioned above,: When i conect my xperia sp to fastboot mode, pressing volume up while plugging in usb cable, the phone led turns to blue for few seconds and than it just turns to red showing on the screen the battery image( normal charging mode)...... I' m using windows xp and a rooted xperia sp whit cm11 (for locked bootloader obviously). Just two last things:
the phone can be unlocked( I checked it) and fastboot worked the same as now with stock xperia sp firmware.
Please i need a final and a certain solution for this problem!!!
i'll be very thankful to anyone who give me a hand!!!!
Click to expand...
Click to collapse
Are you trying to unlock your phone?
Have you installed device specific/fastboot/flashmode drivers via FlashTool? If you are on Windows 8/8.1, you need to disable driver verification to get it done.
Alternatively if you just wanna unlock your bootloader, you can use the BLU option in FlashTool. Again all drivers will need to be properly installed for your phone to be detected correctly.
You say you had the same problem with stock firmware which means you probably haven't setup adb/fastboot properly on your PC. Does your phone get detected correctly in Device Manager? Have you tried installing drivers via Device Manager?
....
So the solution is installing flashtool and installato drivers via Emma?? Thanks forma the attention!!
TheTras said:
So the solution is installing flashtool and installato drivers via Emma?? Thanks forma the attention!!
Click to expand...
Click to collapse
I meant install drivers via FlashTool. Go to C:\Flashtool\drivers or wherever you have installed Flashtool and run the Flashtool-drivers.exe.
Select flashmode drivers, fastboot drivers and common drivers viskan board (SP drivers) and install them. Like I said if you are on Win 8/8.1, you will have to disable driver signature enforcement. Just look it up in YouTube and follow a tutorial.
i try to flash my device but fast boot recovery bricked now i cant open droid boot or android Os. when i try to power on device an USB logo show in the screen and device powered off in 1 second. in my device connect to computer via USB cable ,USB logo remain in screen for a few minutes. fastboot and adb cant find my device. any one can help me?? tanks
Sorry for the Long wait
I hope u receive this before going off to buy a new tablet.Or did u send it to Asus warranty and did they give u a new one for free.(Plzz reply and tell me. Also I found this procudure in how to get adb and fastboot to work again. Go to this fourm http://forum.xda-developers.com/memo-pad-7/general/howto-unbrick-hardbricked-memo-pad-t3105945 and follow the instrucftions. it works with the me170cx well but with other versions not so much. i'm going to try this and hopefully this works:laugh:
Does anyone know how to unlock me170c bootloader and have custom recovery installed?
Bricked Asus Me70cx
I am having the exact same problem. Tried using Intel flash tool and keep getting windriver error timeout. I have tried starting flash before usb screen comes and waiting for screen to load. I have loaded all usb drivers like other post state and still can't get tablet working. Please someone help!
Hello all, my LGWR doesn't enter anymore in fastboot mode (swipe from 11 to 5 does nothing) i was wondering if a fastboot cable would help, i saw that some moto and kindle devices can be unbricked with that cable.
Cannot post a link yet but search on amazon "Fastboot-Motorola-Factory-Atomic-Market"
have any of you tried that ? i think in the case of LGWR the cradle should be opened and pin 1 (Vcc) connected to pin 4 (NC). maybe trough a resistor ? of what value ?. I ordered a cradle from china to "hack" it but it takes 30 days to reach me... Somebody can try that faster than me (have a cradle, open it etc)?
thank you
did you try abd to enter fastboot?
when i connect it to PC it says "usb device not recognised" and "unknown device" and i cannot add a proper driver. I tried a few drivers, which one should i use?
thank you
furygreen said:
when i connect it to PC it says "usb device not recognised" and "unknown device" and i cannot add a proper driver. I tried a few drivers, which one should i use?
thank you
Click to expand...
Click to collapse
i format my pc, install windows 10 enterprise, then install adb 1.4.2 from here http://forum.xda-developers.com/showthread.php?t=2588979..when connect smartwatch, windows find the driver..if adb see your smartwatch you solve your problem i hope
does the watch boot?
sometimes it restarts after a few seconds (during coloured balls animation), sometimes it boots up to "Android is stating / app xx of xx" and after it finishes "Power off.../shutting down"
I'm using the google translator because I don't speak English-
I need help with the conversion of realme gt neo flash to X7 max 5g indian version, I follow all the guide and when starting MTKAuthBypassTool I get the following error "ERROR STATUS ERR 0XC0010001".
The phone does not restart, it continues off, then I disconnect the usb cable to repeat the bypasstool step and it gives me the following error "BRom protocol error ACK a0 = a0". Following this I click on DOWNLOAD and the following error appears "ERROR STATUS BROM CMD START CMD FAIL 0XC0060001"
I don't know what I'm doing wrong, I had already followed this tutorial twice and both times with success, but this time there is no way to transform it to X7 max 5g
*I was testing customs roms, exactly the lineage os, which doesn't go beyond the logo.
try uninstalling and installing the lib and vcom drivers
to install the v com drivers open the setup and at the last screen where the different devices are listed connect your phone and select RMX3031 and install
try this !
e_v_i_l_x_ said:
try uninstalling and installing the lib and vcom drivers
to install the v com drivers open the setup and at the last screen where the different devices are listed connect your phone and select RMX3031 and install
try this !
Click to expand...
Click to collapse
got the same problem as his and try ur tips but still doenst work
U_dinz said:
got the same problem as his and try ur tips but still doenst work
Click to expand...
Click to collapse
Error 0xC0060001
Message: BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (0xC0060001)
Meaning: The device attempted to power on before SP flash tool could flash files to it
Solution:
The device might require a custom Download Agent (DA) to be flashed
Ensure the battery is well charged
Take out and reinsert the battery
Try using a different USB cord, port and PC
Right-click flash_tool.exe > Select Properties > Select Compatibility > Set to Windows XP Service Pack 3 > Click Apply > Click OK > Run SP flash tool as Administrator
Try a different USB cord
Try a different port on the PC or another PC
Ensure the battery is well changed and inside the switched off phone before connecting to PC for flashing
Do not hold any button when connecting to PC
fcxo912 said:
I'm using the google translator because I don't speak English-
I need help with the conversion of realme gt neo flash to X7 max 5g indian version, I follow all the guide and when starting MTKAuthBypassTool I get the following error "ERROR STATUS ERR 0XC0010001".
The phone does not restart, it continues off, then I disconnect the usb cable to repeat the bypasstool step and it gives me the following error "BRom protocol error ACK a0 = a0". Following this I click on DOWNLOAD and the following error appears "ERROR STATUS BROM CMD START CMD FAIL 0XC0060001"
I don't know what I'm doing wrong, I had already followed this tutorial twice and both times with success, but this time there is no way to transform it to X7 max 5g
*I was testing customs roms, exactly the lineage os, which doesn't go beyond the logo.
Click to expand...
Click to collapse
Same errors bro, How to correct?
w2sboyz said:
Same errors bro.
Click to expand...
Click to collapse