Hello yesterday i bricked my phone when i tried to install twrp recovery. Now my phone is bootlooping from last night. I can't get into fastboot or recovery and the spflashtool does not read the COM port. Can someone help please!!
How to install:
1. Download the attached file: VD171_MTK-bypass.zip.
2. Extract the file and open the folder.
3. Run and install python: python-3.9.1-amd64.exe.
Keep atention: You need to select "Add Python to PATH" before starting the installation.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
4. Open cmd or powershell and execute this command:
pip install pyusb pyserial json5
5. Go to the Driver folder and right-click on the cdc-acm.inf file, then click Install and then, close window.
6. Run and install filter wizard: libusb-win32-devel-filter-1.2.6.0.exe.
7. Launch filter wizard.
8. Select Install a device filter and click Next.
9. Connect powered off phone with volume- button to boot in EDL mode.
10. Once you see new MediaTek USB Port in the list, select it and click Install.
Now, you are ready for bypassing EDL !
How to bypass:
1. Go to the Bypass folder. Run the script: bypass.bat.
2. Connect powered off phone with volume- button to boot in EDL mode.
3. Once you get "Protection disabled" at the end, without disconnecting phone and usb, run SP Flash Tool.
4. Once the SP Flash Tool opens, click Options > Options > Connection.
5. Select UART mode and select Baud rate to 921600.
Now, you are ready for flashing !
How to update the tool:
1. Download latest release of the tool: https://github.com/MTK-bypass/bypass_utility/releases/latest
2. Download latest release of payloads: https://github.com/MTK-bypass/exploits_collection/releases/latest
3. Extract the content of both files to the Bypass folder.
It is updated now.
https://forum.xda-developers.com/attachments/vd171_mtk-bypass-v1-5-zip.5228529/
well there it is follow those steps..
well there it is follow those steps
Stefy1337 said:
Hello yesterday i bricked my phone when i tried to install twrp recovery. Now my phone is bootlooping from last night. I can't get into fastboot or recovery and the spflashtool does not read the COM port. Can someone help please!!
Click to expand...
Click to collapse
you did try booting into EDL right?
Keno_I said:
well there it is follow those steps
you did try booting into EDL right?
Click to expand...
Click to collapse
no, I didn't try. If you refer to edl points I tried to press them but nothing happens. And the spflashtool does not detect the com port.
What port did you connect through, try changing usb ports.
And plugging into usb 2.0
Keno_I said:
What port did you connect through, try changing usb ports.
And plugging into usb 2.0
Click to expand...
Click to collapse
i got only 3.0
You need usb 2.0 it isnt recognized on 3.0.....
Keno_I said:
You need usb 2.0 it isnt recognized on 3.0.....
Click to expand...
Click to collapse
I'll try to get it. Does it work if I use an external USB connected to 3.0?
Im not sure, but try it, all i know that spflashtool doesn't work nicely with USB 3.0 idk why
Keno_I said:
Im not sure, but try it, all i know that spflashtool doesn't work nicely with USB 3.0 idk why
Click to expand...
Click to collapse
Ok thanks a lot <3
Keno_I said:
Im not sure, but try it, all i know that spflashtool doesn't work nicely with USB 3.0 idk why
Click to expand...
Click to collapse
i will update you if i fix it
Stefy1337 said:
i will update you if i fix it
Click to expand...
Click to collapse
Okay, good luck!
Kenora_I said:
Okay, good luck!
Click to expand...
Click to collapse
got this error when open bypass
Traceback (most recent call last):
File "D:\shared folder vmware\VD171_MTK-bypass-v1.5\Bypass\main.py", line 3, in <module>
from src.exploit import exploit
File "D:\shared folder vmware\VD171_MTK-bypass-v1.5\Bypass\src\exploit.py", line 2, in <module>
from serial.serialutil import SerialException
ModuleNotFoundError: No module named 'serial'
Stefy1337 said:
got this error when open bypass
Traceback (most recent call last):
File "D:\shared folder vmware\VD171_MTK-bypass-v1.5\Bypass\main.py", line 3, in <module>
from src.exploit import exploit
File "D:\shared folder vmware\VD171_MTK-bypass-v1.5\Bypass\src\exploit.py", line 2, in <module>
from serial.serialutil import SerialException
ModuleNotFoundError: No module named 'serial'
Click to expand...
Click to collapse
pip install pyserial
Do that if you have python 2
Python 3 may be
pip3 install pyserial
Kenora_I said:
pip install pyserial
Do that if you have python 2
Python 3 may be
pip3 install pyserial
Click to expand...
Click to collapse
hey dude its me again .. i did it .. i bypassed the protection but can you teach me how to use sp flash tool and update frimeware so i can unbrick my device.. please
Update : somehow i managed to get back the recovery and fastboot but still not booting.. idk how to reinstall the rom
Update : Unbricked using mi flash tool and this tutorial https://c.mi.com/oc/miuidownload/detail?guide=2
Love Kenora for help <3
Sorry I was busy but nice to hear it worked!
Related
Hi I've been trying to root this phone all day and I'm getting to the stage were this phone might fly out my window if i can get this sorted soon so I'm asking for some help with the issues I'm having i managed to unlock the phone i can boot into fast boot but i cant boot into twrp i have read numerous guides but I'm still stuck and Iv never really used command prompt either so I'm lost with that if anyone can talk me through this
Sent from my MI 5 using Tapatalk
Are you on miui MM or N?
I'm on miui global 8.2|stable 8.2.2.0 (naamieb)
Sent from my MI 5 using Tapatalk
I'm assuming you have usb debugging, adb drivers and all set up.
If you've set any password or pattern lock or PIN, remove it
Download this https://drive.google.com/open?id=0B8rqkXJNwRqLa1JIY1B5TGpkN2M
Extract to your desktop
Download latest twrp 3.1.0-x . Link is available in another thread in this forum
Place the downloaded image on your phone's internal memory
Power off and enter fastboot mode. Connect to your PC
Open the folder you had extracted earlier. Rename the recovery image to twrp.img
Press shift+right click and open command window
Execute this code
fastboot devices (to make sure if phone is being detected properly.)
fastboot boot twrp.img
Now it will boot into the recovery. The recovery is in chinese by default. In the main screen, select the sixth option which is settings, then select the rightmost tab on the next screen and change the language.
Next install the latest twrp image you had placed on phone memory earlier, select "Recovery" and reboot. You will have installed twrp permanently.
Then flash supersu 2.79 and you're set
when I extract the files it dosent create a folder just the files I can just make the folder but what do I name it also theres no recovery image file
casuk said:
when I extract the files it dosent create a folder just the files I can just make the folder but what do I name it also theres no recovery image file
Click to expand...
Click to collapse
Just create a new folder on desktop and extract to it. The file named ZCX-TWR-3.0.2-X... Is the image file which you need to rename to "twrp"
thanks mate I done that when I try to drag n drop the twrp-3.0.2-0-gemini file to my phone it it fails saying the device has either stopped responding or has been disconnected
casuk said:
thanks mate I done that when I try to drag n drop the twrp-3.0.2-0-gemini file to my phone it it fails saying the device has either stopped responding or has been disconnected
Click to expand...
Click to collapse
You're having issue with copying files to your phone storage?
Reinstall the Xaiomi drivers
how do I reinstall the drivers, also when the phone is connected to the pc if I go to the phone it says portable media player and its empty inside.
and when I go to command prompt and type fastboot devices I get a code then fastboot and then I type fastboot boot twrp.img it says could not load twrp.img : no error
I can't get this working i done all in you guide i have downloaded the drivers but still can't get by the phase i posted above what do i do next
Sent from my MI 5 using Tapatalk
It's okay if it shows portable media player but if it's not showing any files inside it, you have a problem. Go to developer options > enable USB debugging and click Revoke USB authorisations. Device drivers install automatically when the device is connected but you can get them seperately as well, just search for mi 5 drivers and install them. Now connect to PC and see if you can access files on your device. If you can, proceed with the guide I've given
When you say device drivers install automatically when the device is connected do you mean they install to the PC
Sent from my HTC One using Tapatalk
I have installed the drivers as far as I'm aware
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my HTC One using Tapatalk
Hi I'm still not able to install/flash twrp so i can root my device i think it's something to do with the device not the pc as phone storage is empty any ideas what i should do
Sent from my MI 5 using Tapatalk
download mi flash http://api.bbs.miui.com/url/MiFlash
install mi flash if you are on windows 8 or above, you need to disable driver singnature enforcement - how to? google it.
during mi flash installation some windows will pop up, just click install this driver anyway. after installation go to c: > xiaomiflash > source > thirdparty > google > android then shift + right click > open command window here. Power off your phone and boot into fastboot then connect to pc. On command window type fastboot devices if xxxxxxx fastboot or something show up on next line, you successfully install fastboot driver.
I have already done that and got f******9 fastboot
then I type fastboot boot twrp.img and I get
cannot load 'twrp.img' = no error
that's exactly what comes up in command prompt and that's as far as I can get also if I boot into recovery I get 3 options reboot, wipe or im assistant so twrp has not installed,
iv been at this for 3 days now and im not any further than I was back then
See if i factory reset my phone and start fresh would i loss my unlocked status
Sent from my MI 5 using Tapatalk
casuk said:
I have already done that and got f******9 fastboot
then I type fastboot boot twrp.img and I get
cannot load 'twrp.img' = no error
that's exactly what comes up in command prompt and that's as far as I can get also if I boot into recovery I get 3 options reboot, wipe or im assistant so twrp has not installed,
iv been at this for 3 days now and im not any further than I was back then
Click to expand...
Click to collapse
Try to install twrp, fastboot flash recovery xxx.img.
And if you want temporarily, fastboot boot recovery xxx.img.
If you are on miui, you must use zcx twrp or else it won't boot.
Good luck.
done as you say still no boot into twrp
casuk said:
done as you say still no boot into twrp
Click to expand...
Click to collapse
I think something is wrong with your twrp.img. Try redownloading. Use latest twrp from twrp.me or zcx from afh.
fastboot flash recovery xxx.img, then disconnect the phone. Press and hold power+vol_up until you see mi logo.
It would be great if there's a way to root without the need to resetting
pruh said:
It would be great if there's a way to root without the need to resetting
Click to expand...
Click to collapse
Bootloader must be unlocked to root. Any time bootloader is unlocked, phone is wiped.
e
Tulsadiver said:
Bootloader must be unlocked to root. Any time bootloader is unlocked, phone is wiped.
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
pruh said:
e
View attachment 5238617
Click to expand...
Click to collapse
Looks like your bootloader is at least ticked to unlock bootloader (or did you do that?). Make sure usb debugging is also ticked. Do you have a windows pc??
If you haven't already, install sdk platform tools on your pc.
SDK Platform Tools release notes | Android Studio | Android Developers
Android SDK Platform-Tools is a component for the Android SDK.
developer.android.com
You will need the boot.img for the firmware you are running. If you can't get it, send give a link to that exact firmware and I'll extract it.
You will also need the canary magisk app here:
https://github.com/topjohnwu/Magisk. Get the canary one.
Steps
Pur boot.img on phone sdcard
Install magisk canary app
Open app. Inside app, at top find and click on install magisk.
Select patch file. Find and select boot.img, hit "lets go". It'll patch file and put in your download folder (magisk_patched***.img).
Put this .img on your pc in the folder where you unzipped the sdk platform tools Rename just magisk_patched.img for simplicity. Open command window in that folder.
Boot your phone to bootloader mode (fastboot).
Plug phone into pc.
In your command window first type "fastboot devices". You should see your phones serial number. If not, there's a problem and the pc doesn't see your phone.
After you see your serial number, next type "fastboot flash boot magisk_patched.img"
Reboot and you should be rooted.
These are the steps for my phone, anyway. No data lost.
Tulsadiver said:
Looks like your bootloader is at least ticked to unlock bootloader (or did you do that?). Make sure usb debugging is also ticked. Do you have a windows pc??
If you haven't already, install sdk platform tools on your pc.
SDK Platform Tools release notes | Android Studio | Android Developers
Android SDK Platform-Tools is a component for the Android SDK.
developer.android.com
You will need the boot.img for the firmware you are running. If you can't get it, send give a link to that exact firmware and I'll extract it.
You will also need the canary magisk app here:
https://github.com/topjohnwu/Magisk. Get the canary one.
Steps
Pur boot.img on phone sdcard
Install magisk canary app
Open app. Inside app, at top find and click on install magisk.
Select patch file. Find and select boot.img, hit "lets go". It'll patch file and put in your download folder (magisk_patched***.img).
Put this .img on your pc in the folder where you unzipped the sdk platform tools Rename just magisk_patched.img for simplicity. Open command window in that folder.
Boot your phone to bootloader mode (fastboot).
Plug phone into pc.
In your command window first type "fastboot devices". You should see your phones serial number. If not, there's a problem and the pc doesn't see your phone.
After you see your serial number, next type "fastboot flash boot magisk_patched.img"
Reboot and you should be rooted.
These are the steps for my phone, anyway. No data lost.
Click to expand...
Click to collapse
Thanks!
Hello everyone! So after the new mediatek DAA and SLA protection bypasses you can find github repo of here , using the bypass we are able to use SPFlash Tool, here is a guide how you can do it! This guide is for RMX3151 (Realme 8i) and RMX3286 (Narzo 50) ONLY. DON'T DO ANY OF THESE IF YOU HAVE SOMETHING ELSE!
ALWAYS USE DOWNLOAD ONLY MODE OF SP FLASH TOOL.
DON'T TOUCH ANYTHING RELATED TO FORMAT ON SP FLASH TOOL! (IT'S WRITTEN EVERYWHERE, YOU WILL LOSE YOUR IMEIS IF YOU USE FORMAT ALL + DOWNLOAD. YOU ARE SAFE IF YOU USE DOWNLOAD ONLY.)
Windows Method
Requirements:
Bypass Tools Pack - (DRIVER AND BYPASS FILES)
SP Flash Tool
Decrypted OFP (OPPO FIRMWARE PACKAGE) Files:
FULL FIRMWARE - INCLUDES THE "USERDATA" PARTITION, HENCE LARGER.
A.32 (Indian) - Mega | GDrive
A.32 (Global) - Mega | GDrive
A.30 (Indian) - Mega | GDrive
These firmwares are from Realme 8i but will work for Narzo 50 also (I will add Narzo 50 firmwares soon)
Install Python from Windows Store
libusb-win32 - Having Issues? Use this.
Get usbdk installer (.msi) from here and install it
1) Extract the zip
2) Go to driver folder, find the .inf file right click and press install.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3)Download this file and install it, after installing power off phone and connect to pc while holding Vol+- (don't leave the buttons after connecting) . You might need this driver as well if it's not detected.
Press next, connect your device to PC while holding Vol+- buttons (your device needs to be powered off, and don't leave the buttons) and you will see the mtkdriver down below. Install it.
Choose MediaTek USB Port and install it.
4)Then run the brom.bat under Bypass folder.
5) Now power off the phone and connect the phone while holding volume + and - (Don't leave the buttons until the bypass is done)
6)After the above step Go into Flash Tool folder and open the SPFlash tool go to Options>Option
Click on Connections and select UART and set Baud Rate to 921600
7) after that choose scatter file and also if not set, set your download-agent. You don't need to select auth file as authorization is disabled. Once you do it, it should look like this. ALWAYS MAKE SURE DOWNLOAD ONLY MODE IS SELECTED! DON'T SELECT OTHER MODES!
Make SURE "Download Only" is selected. Don't select ANYTHING ELSE! You will lose your IMEIs, Serial Numbers, Capability of Hardware Attestation etc. if you choose "Format data + Download" make SURE you selected "Download Only".
8) Uncheck oplusreserve2 first. Now, you can start downloading with the button and after that a checkmark will appear. You can reboot your phone and use it like before now! All your userdata will (inevitably) be cleared!
After flashing it should look like this. Download has been complete. Enjoy!
Notes :
After this phone might not boot due to encryption, you can do any of the below procedures to format your data and boot your phone
1. In case you can access recovery by holding volume and power button - Wipe all data from recovery and reboot
2. In case you cannot access recovery, power off phone then enter this command in mtkclient :
Code:
python mtk e metadata,userdata,md_udc
and connect phone while holding both volume buttons. After this just reboot phone
Also note that first boot takes some time, so don't panic leave it for few minutes it'll boot
Credits :
https://github.com/bkerler/ for decryptor and for creating the tool.
If you face any issues contact me here
great.. does this lock bootloader?? and will SafetyNet pass after this??
It doesn't work.Returns an error.
Why do you have another phone identified in the last screenshot.?And when the firmware reaches the file oplusreserve2.img gives an error that I posted yesterday?Take a look at the screenshot above.
And this is not a firmware, it takes a minute.Does not flash the super partition.You can just flash the stock files to recover and THAT's IT.
sany.svenson said:
Why do you have another phone identified in the last screenshot.?And when the firmware reaches the file oplusreserve2.img gives an error that I posted yesterday?Take a look at the screenshot above.
Click to expand...
Click to collapse
The last screenshot is for representative purpose only... No one have actually bricked yet so... The guide is pretty generalized for any mtk... If you have followed the guide properly it should work... Let me upload A32 firmware here try that.
I updated the link with latest sp flash tool... Try with that
sany.svenson said:
And this is not a firmware, it takes a minute.Does not flash the super partition.You can just flash the stock files to recover and THAT's IT.
Click to expand...
Click to collapse
edit the scatter file find "super.img" and change is_download: "false" to "true" then save it and flash
pritish1998 said:
I updated the link with latest sp flash tool... Try wit
Click to expand...
Click to collapse
pritish1998 said:
The last screenshot is for representative purpose only... No one have actually bricked yet so... The guide is pretty generalized for any mtk... If you have followed the guide properly it should work... Let me upload A32 firmware here try that.
Click to expand...
Click to collapse
I unpacked 32 firmware myself.I have it.
sany.svenson said:
I unpacked 32 firmware myself.I have it.
Click to expand...
Click to collapse
Did you merge the super.img?
pritish1998 said:
Did you merge the super.img?
Click to expand...
Click to collapse
sany.svenson said:
I unpacked 32 firmware myself.I have it.
Click to expand...
Click to collapse
Also the given A30 fw is fine just edit the scatter file and make super.img flash true
pritish1998 said:
Also the given A30 fw is fine just edit the scatter file and make super.img flash true
Click to expand...
Click to collapse
can you upload a scatter file here?
sany.svenson said:
can you upload a scatter file here?
Click to expand...
Click to collapse
@bobongros please upload it for him
bobongros said:
edit the scatter file find "super.img" and change is_download: "false" to "true" then save it and flash
Click to expand...
Click to collapse
can you upload a scatter file here?
sany.svenson said:
can you upload a scatter file here?
Click to expand...
Click to collapse
I updated the firmware link just use it... it'll work fine... Also after bypass you don't need to hold volume buttons
pritish1998 said:
I updated the firmware link just use it... it'll work fine... Also after bypass you don't need to hold volume buttons
Click to expand...
Click to collapse
It reaches oplusreserve2 and an error comes out.The fleshtul from the new link does not want to read the scatter file.Writes that it does not work with this processor.
Sorry.You're tired of me already...
sany.svenson said:
It reaches oplusreserve2 and an error comes out.The fleshtul from the new link does not want to read the scatter file.Writes that it does not work with this processor.
Sorry.You're tired of me already...
Click to expand...
Click to collapse
Other people tried and it's working for them... Idk what is the problem at your end. ... Reach out to me on telegram we will help
pritish1998 said:
Other people tried and it's working for them... Idk what is the problem at your end. ... Reach out to me on telegram we will help
Click to expand...
Click to collapse
sany.svenson said:
View attachment 5480563
Click to expand...
Click to collapse
with that fleshtul that you posted last.How can I find you in a telegram?Give me a link to your profile.
Hi, sorry but I don't know English well, I was wondering if you could give me the download link of the TWRP for this phone, thanks ......
Redmi Note10 5G EEA
Frankie1975 said:
Hi, sorry but I don't know English well, I was wondering if you could give me the download link of the TWRP for this phone, thanks ......
Redmi Note10 5G EEA
Click to expand...
Click to collapse
Here:
https://forum.xda-developers.com/t/unofficial-twrp-camellia-camellian.4304717/
sorry not run....
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Frankie1975 said:
sorry not run....
Click to expand...
Click to collapse
Why install the twrp since there is currently no flashed custom rom and there won't be any soon because of the mediatek soc which is little or not developed.
Have you unlocked the bootloader?
Frankie1975 said:
sorry not run....
Click to expand...
Click to collapse
There is no [recovery] partition on this phone.
yes i unlocked it, how do i recover the partition?
Frankie1975 said:
yes i unlocked it, how do i recover the partition?
Click to expand...
Click to collapse
this is A/B device it doesn't have recovery partition
Frankie1975 said:
yes i unlocked it, how do i recover the partition?
Click to expand...
Click to collapse
Reboot the phone to fastboot (Power + Vol Down)
Connect the phone to the computer using an USB cable (Preferred to use original cable that came with the phone)
Extract the fastboot files and open CMD/Terminal there.
Paste the twrp.img in the same folder.
Type' fastboot boot twrp.img' without the apostrophes.
The phone will reboot in TWRP after that go to Advanced > Flash Current TWRP.
But why?(Again).
If it is to change rom version use this tool:
https://forum.xda-developers.com/t/flash-tool-guide-use-xiaomi-flash-tool.4262425/
not running
Frankie1975 said:
not running
View attachment 5609485
Click to expand...
Click to collapse
https://www.droidwin.com/fix-status-read-failed-too-many-links/
changed drivers
changed cable
but it gives me the same two errors as before, even if I only write to the boot partition ....
Frankie1975 said:
changed drivers
changed cable
but it gives me the same two errors as before, even if I only write to the boot partition ....
Click to expand...
Click to collapse
Again why would you want to install the TWRP?
I am Italian and know little English I have no reference guides for your procedure ....
Frankie1975 said:
I am Italian and know little English I have no reference guides for your procedure ....
Click to expand...
Click to collapse
use google trad https://translate.google.fr/?sl=it&tl=en&op=translate
too dangerous .... with the twrp I finished the job, only the magicsk is missing, and I finished the root ..
Frankie1975 said:
too dangerous .... with the twrp I finished the job, only the magicsk is missing, and I finished the root ..
Click to expand...
Click to collapse
No need Twrp to root
and how do you install the magisk?
Frankie1975 said:
and how do you install the magisk?
Click to expand...
Click to collapse
1. Find or redownload the TGZ file for your current ROM
2. Browse inside the zip file and find boot.img under the images folder
3. Copy this file to a temporary location in your PC first, and then transfer it to your phone
4. Install the desired version of Magisk app (V23?)
5. Run the app and choose Install under Magisk
6. Choose Select and Patch a File, then select the boot.img that was transferred earlier
7. A process will run and create a new .img file in the same folder where the original one was
8. Transfer the new file to your PC in the same directory where fastboot.exe is located
9. Open a command prompt window in that same directory
10. Reboot your phone to fastboot mode and connect to PC, USB2.0 port. Check for connection by running command fastboot devices.
11. Run the command fastboot flash boot_ab magiskXXXX.img
Once it's completed, run command fastboot reboot and the phone should boot and be rooted.
thanks for the support, but I have ascertained that I have problems with USB 3.0 I think that's all the problem, I'm very close to the solution, sorry but I leave your guide alone, if I have problems I will opt for your advice. Now I try the "fastboot boot twrp.img" with USB 2.0, then I say hello
Frankie1975 said:
thanks for the support, but I have ascertained that I have problems with USB 3.0 I think that's all the problem, I'm very close to the solution, sorry but I leave your guide alone, if I have problems I will opt for your advice. Now I try the "fastboot boot twrp.img" with USB 2.0, then I say hello
Click to expand...
Click to collapse
Usb 3 is not recommended, I already told you on a previous post.
Hello! I was bored and I thought that it would be a pretty cool idea to make an updated, universal guide to unlock the Realme 8i/Narzo 50, since there is no deeptest.apk or accessible fastboot for these devices.
THIS GUIDE WILL ERASE ALL OF YOUR DATA! MAKE A BACKUP!
/*
* This Guide is tested and working
* However I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about unlocking and flashing TWRP
* before flashing it! YOU are choosing to make these modifications.
*/
This guide is made for Windows.
Step 0
Requirements
Download and install the latest version of Python. (Windows 10/11; Other OSs)
Download and install USBdk. (here)
Download and extract mtkclient.
Download your device's drivers. (here, we will install them later)
Download this file and copy it to the mtkclient folder.
Open the mtkclient folder, right click on it while you press Shift and then click "Open in Terminal" or something like that.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Step 1
Unlocking Bootloader
Type pip install -r requirements.txt and press enter.
Type python mtk e metadata,userdata,md_udc and press enter.
Now turn off your phone, and while you press both volume buttons you connect your phone to the PC via a USB cable. DON'T RELEASE THOSE BUTTON EVER!
When it finished and while you continue to press both volume buttons, type python da seccfg unlock.
When the last command has finished, you can release both buttons, disconnect the phone and reboot it untill you see the Realme logo.
When you see the Realme logo, PRESS AND RELEASE THE POWER BUTTON!
This boot will take a while, just wait and re-configure your phone!
Step 2
Installing TWRP
Type python mtk w lk lk.bin and press enter.
Now turn off your phone, and while you press both volume buttons you connect your phone to the PC via a USB cable. DON'T RELEASE THOSE BUTTON EVER!
When the last command has finished, you can release both buttons, disconnect the phone and reboot it.
Now turn your phone off again and turn it on while pressing Vol-, a screen like this should appear.
Now, with your phone connected to your PC, open up Device Manager on your PC.
Right click on the device that's called Android and press Update driver.
Select 'Browse my computer for drivers'
Select Browse and select the file android_winusb.inf that is in the drivers folder.
When you're done, close Device Manager, install ADB from here and open the app Minimal ADB and Fastboot.
Download TWRP and type in terminal fastboot flash recovery <path to TWRP>
When it's done, type fastboot reboot recovery and you should boot straight to TWRP!
Step 2
Rooting
On your PC, download the Magisk APK, rename it to magisk.zip and copy it to your phone's memory.
On TWRP, flash the Magisk zip and you're good to go!
Credits
Thanks to Pritish and Sidharth for making the OG guides which I merged!
Thanks for the TWRP staff for... creating TWRP ig
Thanks to shimp208 for making the Minimal ADB and Fastboot tools!
Join the Telegram Group!
If you need help, join the Telegram group or leave a comment down here!
Iam on realme ui 3....does this will work for me....???
ankitpant said:
Iam on realme ui 3....does this will work for me....???
Click to expand...
Click to collapse
same question.
and if have to downgrade can i upgrade later? and root it? or it'll block bootloader again?
anyway to root in realme UI3.0 with magisk?
Hi
I apply your method, i was unlocked bootloader successfully but when i enter this command 'python mtk w lk lk.bin' my device can't boot, just black screen
Realme UI 3
sakib7040 said:
I apply your method, i was unlocked bootloader successfully but when i enter this command 'python mtk w lk lk.bin' my device can't boot, just black screen
Realme UI 3
Click to expand...
Click to collapse
Hi,
Connect phone to original wall charger and wait for it to BUZZ (5 to 10 minutes). Then proceed to pritish1998 unbricking method.
Also installing TWRP via this method should be tried with rui2.
Hope it helps
is this still work today 7/02/2023
Yes. This method work's under rui2
OatSiriM said:
is this still work today 7/02/2023
Click to expand...
Click to collapse
does this work with python 3.8.10? since i only have win7 x64
also realme8i TWRP can this be use with narzo 50?
ghochenk said:
does this work with python 3.8.10? since i only have win7 x64
also realme8i TWRP can this be use with narzo 50?
Click to expand...
Click to collapse
Pythons 3.8.1 will work. As for the realme flash tool stick to 2.xx. as the lastest 3.xx does not seam to recognise the phone
zachitou said:
Pythons 3.8.1 will work. As for the realme flash tool stick to 2.xx. as the lastest 3.xx does not seam to recognise the phone
Click to expand...
Click to collapse
Thank you
zachitou said:
Pythons 3.8.1 will work. As for the realme flash tool stick to 2.xx. as the lastest 3.xx does not seam to recognise the phone
Click to expand...
Click to collapse
What to do if I’m under Realme UI 3 ? I can’t do it ?
Realme ui 2 works. Realme ui3 should work. I had No luck with ui 4
zachitou said:
Realme ui 2 works. Realme ui3 should work. I had No luck with ui 4
Click to expand...
Click to collapse
Idk If I wanna do it because I’ve seen a lot of people bootloop :/
HadesBar said:
What to do if I’m under Realme UI 3 ? I can’t do it ?
Click to expand...
Click to collapse
You can but you need lk file for rui3
sakib7040 said:
I apply your method, i was unlocked bootloader successfully but when i enter this command 'python mtk w lk lk.bin' my device can't boot, just black screen
Realme UI 3
Click to expand...
Click to collapse
You need lk file for rui3
HadesBar said:
Idk If I wanna do it because I’ve seen a lot of people bootloop :/
Click to expand...
Click to collapse
You won't get any bootloop if you use proper files
zachitou said:
Realme ui 2 works. Realme ui3 should work. I had No luck with ui 4
Click to expand...
Click to collapse
You can root rui4