Related
Greetings everyone!
Few weeks ago, I gave my device to a friend of mine to manually update it. Something went wrong so he decided not to go any further. Yday i tried to "Factory reset", after reset some error pop'd in the left upper corner of the phone.It says:
[LGE_SECURITY] ERROR: boot image signature
Critical failure: Unable to start kernel.
Unrecoverable bootloader error (0x00000002).
Anyone had any similiar or even the same problem as i am facing right now? Thanks in advance.
best regards, Milan
Guy didn't know what he was doing apparently. Your handset is still locked and he apparently tried installing a 3rd party ROM, lemme guess, you wanted a newer version of Android than 4.1., which is a reasonable enough thing. Problem is that out of the box you can't do that because it only boots images signed by LG and they abandoned development after releasing 4.1 and a couple of minor point releases. You aren't totally screwed but if you were having somebody else do it for you, you might need to get some help. You can find the details elsewhere here, or more likely point a more skilled friend at it, but here it is in a nutshell.
You need to get LG's official updating software (from the LG website) and you need to fiddle with it a bit until you get it to do a rescue because it expects to have already paired up with the phone while it was still working. If you already had it installed, great because it will make it easier. Anyway, you will probably have to manually pick your model and input the IMEI since it won't already know those things and it will go out and fetch the most recent image. You will push VOL Down and insert the USB cable from a powered down state, it will then do the rest. Good chance you will even retain your data unless that 'factory reset' you mention actually succeeded.
Of course that will only get you back to stock 4.1. Read around for the official way and several un-official ways to unlock your boot loader. Once that is done you can install a better recovery and then a newer version of Android. But the first step is to restore the stock software since you have to have a running phone to be able to unlock it.
And no, nobody has ever been able to explain WHY they lock them, but every single manufacturer seems determined to do it, chipmakers put a lot of work and ad copy into how extensive and unbreakable the locks on their newest chip is, etc. And then they either bow to customer demand and add an unlock feature or we here at xda do it for them... as a courtesy of course. Truly we do live in the asylum. Wonko the Sane was onto something.
--> From Motorola, but do at your own risk, as always! <---
Lenovo Motorola Smart Assistant - "lmsa"
I've played with, and done some more research on lmsa.
I am wondering if this would help some folks here.
Please report back success or failure and your particular symptom so others will know.
NOTE: my phone is bootloader unlocked XT1900-1 One fi which OTA'ed itself up from 8.1 to 9 Oct 1 '19 security.
If you are able to back anything up, do so before you do this - if successful, it will flash your phone.
go here
https://www.motorola.com/us/lenovo-motorola-smart-assistant
and download it.
Watch the video for software issues(lower left of that page).
Install it.
Start it up.
You want flash/ rescue.
follow the instructions and put your phone into fastboot mode and connect to PC via USB.
If it offers you something(takes a minute), click the little download arrow and when it's downloaded, click rescue.
This is what it looks like for me before I would click the download arrow.
I believe this tool is for people who have a locked bootloader, never unlocked? LMSA won't recognize my device. RSD lite won't either.
Persistent memory has some value that is not overwritten by Wipe All twrp? Of course I will never relock.... just a heads up to others.
I am one of the few.... 1900-1 Fi working fine on Aug Pie factory and wanted to try ionOS. Flashed fine and working good. Now 3 carriers in my area only US Cellular has service. T-Mob--, Sprin- coverage area 10 - 0% Found as I have before No ROM other than stock for ME can get Data services to work on all three carriers in my area. So for data services trying to reflash back to stock. NO factory image successfully flashed will have modems working. For me. Tried many forms of flash modems only via fastboot, nope.
Different flavors of ADB don't help. Now I haven't tried "Hardware tools loader" style because if wrong will brick it. Unless some one has? Various forms of flashing modems, flash all scripts, ADB versions, Hardware only flash from two ROMs (which is why I am here I think) the Wipe All needed for those two roms some how did it? No blame, just for some reason can't flash back to stock. Others have but....I can't. So hoping a forward update by Motorola Factory Image will do a complete modem working Flash.
kkjb said:
I believe this tool is for people who have a locked bootloader, never unlocked? LMSA won't recognize my device. RSD lite won't either....
Click to expand...
Click to collapse
My phone IS bootloader unlocked - I bought it used(ebay) and it came to me that way with a fresh 8.1 It gives the usual bootloader unlocked error message on boot. It has OTA updated itself to 9 Oct 1 '19 security. I have not tried to modify it because that would prevent me from getting future OTAs.
RSDlite latest (6.2.4) does not recognize my phone. That is RSDlite's fault. I don't think it is yet capable of an A/B phone, let alone a full Treble (ours, on 9, are not full Treble, only partial but DO have A/B sets of partitions).
From the attached pic you can see it was ready to flash my phone with the latest stock ROM appropriate for my device which is a 1900-1 One fi, even though it was unlocked.
I am guessing that Motorola invented lmsa to stem the flow of trashed phones to Moto factory repair. It wouldn't surprise me if it would auto blankflash if necessary.
Try it - it only takes a minute or 2 to test! The worst it can say is "no"!
Understand, tried all the options and LMSA needs I think a stock recovery, boot, fastboot flash mode. The various options show "phone not recognized" no mode available with twrp installed to goto Factory Flash as LMSA appears to wait for in Bootloader Mode. So the drop down box screen will not appear since not recognized.
This post was just a update as you had asked for others to give their results. So going to do hand flash of factory images again, see if try many times... and some how one works
kkjb said:
Understand, tried all the options and LMSA needs I think a stock recovery, boot, fastboot flash mode. The various options show "phone not recognized" no mode available with twrp installed to goto Factory Flash as LMSA appears to wait for in Bootloader Mode. So the drop down box screen will not appear since not recognized.
This post was just a update as you had asked for others to give their results. So going to do hand flash of factory images again, see if try many times... and some how one works
Click to expand...
Click to collapse
Thanks.
Bummer this didn't work for you.
Yeah phone definitely needs to be in fastboot mode.
Hopefully it will help others.
Yeah, back when RSDlite worked you could "sledge hammer" just about anything if it would boot to fastboot! Hopefully they will upgrade it...
No Thank You, you gave me some ideas about the a/b devices thoughts. We have the odd ball not 9.0 at release device so the a/b script is different than some devices. So with the newest ROMs using fastboot "flash all zip scripts" for a/b boot slots I think the problem is factory images want something else for the modems. Oddly the factory images flash fine with no errors just that no modems...imei, wifi, blutooth. 8.0,8.1,9.0 all. Its a weird problem.
kkjb said:
No Thank You, you gave me some ideas about the a/b devices thoughts. We have the odd ball not 9.0 at release device so the a/b script is different than some devices. So with the newest ROMs using fastboot "flash all zip scripts" for a/b boot slots I think the problem is factory images want something else for the modems. Oddly the factory images flash fine with no errors just that no modems...imei, wifi, blutooth. 8.0,8.1,9.0 all. Its a weird problem.
Click to expand...
Click to collapse
Yeah I was thinking a-/b prob
If you ran the "flash all fi bat" to install ionOS it would have worked well since, with Aug 9, you were in a 2 file system phone. so i am guessing
a) you would only have success flashing a 9 stock (fi or not)
b) you would probably have to do a preliminary flash with just the stock 9 bootloader etc (the stuff before the ping. as well as maybe the 2 modem erases later in the command stack - some playing needed there...) tons of guesswork and luck needed here!
c) I found it humorous that ionOS script made b active but I hope the dev knew what he/she were doing.
edit d) so what partitions set is active after you flash your tests? ie you flash something, but what are you then booting to - unless you set something active... I don't believe there is a default - just last successful - though I assume if one fails it will try the other. Perhaps endlessly.
But, yeah, I can see why that flash went well. But of course you are then stuck with the modems they flashed and how that particular opsys planed to use them. US cellular is apparently known to be iffy on the X4 since I saw that caveat on a number of ebay x4 sales - "not guaranteed for...". And Sprint, of course is cdma but is supposedly accessible as LTE by fi??? I have zero knowledge there!!!
WARNING WHEN DEALING WITH ME - I TEND TO MAKE A POST AND THEN KEEP EDITING IT ENDLESSLY>>> SORRY!
I just bought a new, unlocked z3p direct from Motorola. Unfortunately, the OTA system update in settings is telling me I'm up-to-date at Jan 1 '19, OPWS28.70-31-8. I've read some pretty awful stuff about using LMSA to flash updates, so I'm curious if there's an official repository of stock roms/updates/etc. and if I can just use ADB to update this thing myself. All I want is latest stock rom+security updates with root. The less involved the process, the better.
Additionally, if I go this route, do I need to manually install each intermediary update, or can I just grab the latest and put it on? A thorough reliable guide is enough; I'm just having trouble finding one that connects all the dots for a simple 'new phone' situation.
I'm fairly well versed at using ADB/flashing/etc. (nexus 4, 5x, g4 play, etc) but it's been two years since I've messed with it. Additionally I have very little idea how to navigate the unusual A/B partitioning.
Thanks!
UPDATE: My Z3P is now up to date with the September 1st security patch and Android 9. I bit the bullet and used LMSA (there's a trick to it) and am posting here so it can help anyone who was in my situation. First I'll list steps that should work for you, and then detail how I did it (which was a little different).
How To:
1. Get LMSA: https://forum.xda-developers.com/general/general/update-moto-lenovo-moto-smart-assistant-t3951714
2. On your device, enable developer options and USB debugging. Ensure you have no screen-lock enabled.
3. Plug your phone in with LMSA open. LMSA app will install on the phone, give it every permission it requests.
4. Select your device model and LMSA will detect the latest build available. Download it.
4a. It might seem like the download is hanging once it reaches 0%. It won't tell you, but the file is being unzipped. Just leave it alone for a while. If the unzip fails, delete some stuff on the volume it's unzipping to.
5. Follow the steps on LMSA to update the phone. DO NOT TOUCH YOUR DEVICE. Just leave it be. It will look like nothing is happening, and/or LMSA will notify you of delays. Ignore them and let it go.
5a. Your device will be on a fastboot screen that prompts you to push the unlock button to "start". DO NOT TOUCH YOUR DEVICE.
What I did:
I got up to step 5, and kept seeing the 'delays'. I thought that it was a signal that LMSA needed me to press 'start' on the device end to help it begin the installation process. Incorrect. As soon as I did so, the LMSA process failed and my phone failed to boot with a message about a corrupt device.
At this point, I switched to the 'recover' tab in LMSA and let it recover with the same image I had downloaded for the update. However, this time, I just left it the hell alone at step 5. It took forever, so I walked away from it, and when I came back, my phone was booted into Pie.
When the fastboot screen is up, LMSA is working in the background to install the image. I'm quite certain that if I hadn't pressed 'start' on my device, my phone wouldn't have corrupted, and the image would have updated correctly. My suspicion is that many of the people having trouble with the LMSA are pressing 'start', which corrupts their devices because it boots while there's an incomplete image flashed to the phone.
Hello all fellow pixelers
After upgrading to 11 i am faxing a ton of issues with my pixel 4 xl such as "clean the top bar", phone calls going to speakerphone etc.
I have tried multiple factory resets with CMD but one thing i am experienced and have never had before is that whenever i am almost done with the reset option via CMD, the message i get is:
E: (libfs_mgr) failed to mount / metadata; formatting: Invalid argument
E: (libfs_mgr) fs_mgr_do_format: Format /dev/block/by-name/metadata as "ext4|""
E: (libfs_mgr) make2fs returned 255
E: (libfs_mgr)failed to format /metadata: Permission denied
E: Cannot mount /metadata/ota
formating /data...
formatting /metadata...
Wiping Titan M..
E:can"t send spi message: Try again
it repeats for 30 times
Data wipe complete
This being said i sure hope someone can and will help me solve this issue as it is becoming a pain, i thank you all in advance for your efforts
It sounds like you're only trying factory resets at the moment. I don't know how to fix this issue, so the only suggestion I have is to try flashing the factory image (which includes a userdata wipe). Don't do the OTA update method. I've been able to fix all my phone problems by flashing the factory image. If that still doesn't work, then I'm thinking there's something physically wrong with the phone.
Colonel_Kosova said:
Hello all fellow pixelers
After upgrading to 11 i am faxing a ton of issues with my pixel 4 xl such as "clean the top bar", phone calls going to speakerphone etc.
I have tried multiple factory resets with CMD but one thing i am experienced and have never had before is that whenever i am almost done with the reset option via CMD, the message i get is:
E: (libfs_mgr) failed to mount / metadata; formatting: Invalid argument
E: (libfs_mgr) fs_mgr_do_format: Format /dev/block/by-name/metadata as "ext4|""
E: (libfs_mgr) make2fs returned 255
E: (libfs_mgr)failed to format /metadata: Permission denied
E: Cannot mount /metadata/ota
formating /data...
formatting /metadata...
Wiping Titan M..
E:can"t send spi message: Try again
it repeats for 30 times
Data wipe complete
This being said i sure hope someone can and will help me solve this issue as it is becoming a pain, i thank you all in advance for your efforts
Click to expand...
Click to collapse
Have you tried factory resetting the phone? You do not need a computer. If you do factory reset you'll lose all your data.
Hey there Neo
Thnx for the reply and yes I flashed the phone 4 times now with cmd. I get all the bugs and the messages only when I am flashing Android 11.
I reverted once to 10 I had no issues whatsoever, once I upgraded to 11 again both with cmd and ota I get the same issue.
It is really really is a nuisance, was hoping maybe someone can finde a fix?
Just got the darn phone saved up most a year just to get it, what a dissapointment.
Again thank u
Homeboy76 said:
Have you tried factory resetting the phone? You do not need a computer. If you do factory reset you'll lose all your data.
Click to expand...
Click to collapse
I did and it didn't help, just feel mad I hate to have to sell this phone.
Thank you for the reply
Colonel_Kosova said:
I did and it didn't help, just feel mad I hate to have to sell this phone.
Thank you for the reply
Click to expand...
Click to collapse
Do you have the latest Android SDK Platform-tools r34.0.4?
What cmd are you using to flash the phone?
Guide
This Factory Reset: Settings -> System-> Advanced->Reset options-> Erase all data (factory reset)
Homeboy76 said:
Do you have the latest Android SDK Platform-tools r34.0.4?
What cmd are you using to flash the phone?
Guide
This Factory Reset: Settings -> System-> Advanced->Reset options-> Erase all data (factory reset)
Click to expand...
Click to collapse
Yes I do all the latest versions
I use this as a guide
https://youtu.be/cKXa5iL1kfQ
Ok, Hopefully, someone has a solution to this problem.
Your error messages seem like it's somehow incompatible or you're not allowed to flash. So that made me wonder if you're downloading the right factory image for the right phone variant. (I think I only saw one variant for the android 11; can't recall at the moment.)
From your responses, it sounds like you're using the ota image. I've had problems with ota in the past, so my suggestion is to flash the factory image instead, which is different from ota. (I've had the pixel 4 xl for a year and never had issues with flashing.)
I also don't input the cmd commands manually. I run the "flash all.bat" which comes with the factory image and it does everything for me.
Colonel_Kosova said:
Hey there Neo
Thnx for the reply and yes I flashed the phone 4 times now with cmd. I get all the bugs and the messages only when I am flashing Android 11.
I reverted once to 10 I had no issues whatsoever, once I upgraded to 11 again both with cmd and ota I get the same issue.
It is really really is a nuisance, was hoping maybe someone can finde a fix?
Just got the darn phone saved up most a year just to get it, what a dissapointment.
Again thank u
Click to expand...
Click to collapse
Neo thank you very much for the reply and the hints.
Could you please maybe find and link the right file for me!?
I have never used the method with flash all bat file, this being said i would really appreciate if you could do me that favor and maybe guide me on how to.
I really love my 4 xl and hate the fact that I have these issues, I have been using it like this for some days hoping a fix will pop out there before I install everything back again.
I sincerely thank you for the effort and time
QUOTE=neo_lithic3K;83692801]Your error messages seem like it's somehow incompatible or you're not allowed to flash. So that made me wonder if you're downloading the right factory image for the right phone variant. (I think I only saw one variant for the android 11; can't recall at the moment.)
From your responses, it sounds like you're using the ota image. I've had problems with ota in the past, so my suggestion is to flash the factory image instead, which is different from ota. (I've had the pixel 4 xl for a year and never had issues with flashing.)
I also don't input the cmd commands manually. I run the "flash all.bat" which comes with the factory image and it does everything for me.[/QUOTE]
Opps! Wrong thread, stay safe.
Sorry @neo_lithic3K.
Check to make sure your proximity sensor is working. Mine quit working some time around 11 beta 3 and flashing back to 10 stopped the clean the top bar thing but not the speakerphone problem (screen was staying on up against my ear) Google replaced mine under warranty
(1a) First, here are the preliminary steps. There are alot of instructions at the top of Google's page at: https://developers.google.com/android/images
I assume that you've already followed all those instructions .... especially unlocking your bootloader, enabling USB Debugging from Developer Options, and adding fastboot to your PATH environment variable (and then rebooting your PC).
***NOTE: There are better guides on xda that give you more thorough instructions, so you may want to check those out instead of reading mine below.***
(1b) I assume that you have an unlocked Pixel 4 XL and that you purchased google's version of the phone from the Google Store. I don't know all the different ways someone can buy the Pixel 4 XL. For example, I think Verizon used to sell it but I don't know if Verizon variants can be flashed. If you didn't buy the phone from the US Google store or you bought the phone from another country, then there could be restrictions there that I don't know about.
(1c) I also assume you have a Windows PC. I've never flashed from other types of operating systems.
(2) Download the latest android 11 'coral' factory image at: https://dl.google.com/dl/android/aosp/coral-rp1a.201005.004-factory-1eb5827f.zip
That link is for the file posted on google's webpage for this version: 11.0.0 (RP1A.201005.004, Oct 2020) 1eb5827f98ec68b71bfd651d667a7cf557832f2e2850540d322d2a3a6fcc07a8
(3) Connect your computer to your phone using the usb cable. I assume your phone's usb debugging is already enabled & fastboot is already in your PATH environment variables as mentioned in the instructions earlier. You may get a pop up on your phone to trust the PC. I don't remember the exact wording but you should accept or trust it.
(4) After you download the zip file, unzip it somewhere (preserve the folder structure). You'll find the flash-all.bat located at: \coral-rp1a.201005.004-factory-1eb5827f\coral-rp1a.201005.004\flash-all.bat
(5) NOTE that everything on your phone will be wiped so first backup anything you need.
(6) Boot your phone to the bootloader using the hardware buttons (or you can use the cmd command: adb reboot bootloader).
While your phone is still connected to your PC, run flash-all.bat. (I usually just double-click on the bat file from my Windows PC)
(7) The cmd window will run through a series of commands and your phone screen may change or reboot. At one point (on the fastbootd phone screen), it will look like your phone is not doing anything or waiting for something. Don't do anything.... just wait. You'll know the flashing is done when the cmd window says "Press any key to exit..."
(8) When it's all done, your phone should automatically boot into android and you should see the pixel setup screen.
(9) This resets your phone to factory image. You'll need to follow other steps to root your phone.
Colonel_Kosova said:
Neo thank you very much for the reply and the hints.
Could you please maybe find and link the right file for me!?
I have never used the method with flash all bat file, this being said i would really appreciate if you could do me that favor and maybe guide me on how to.
I really love my 4 xl and hate the fact that I have these issues, I have been using it like this for some days hoping a fix will pop out there before I install everything back again.
I sincerely thank you for the effort and time
QUOTE=neo_lithic3K;83692801]Your error messages seem like it's somehow incompatible or you're not allowed to flash. So that made me wonder if you're downloading the right factory image for the right phone variant. (I think I only saw one variant for the android 11; can't recall at the moment.)
From your responses, it sounds like you're using the ota image. I've had problems with ota in the past, so my suggestion is to flash the factory image instead, which is different from ota. (I've had the pixel 4 xl for a year and never had issues with flashing.)
I also don't input the cmd commands manually. I run the "flash all.bat" which comes with the factory image and it does everything for me.
Click to expand...
Click to collapse
[/QUOTE]
Colonel_Kosova said:
Neo thank you very much for the reply and the hints.
Could you please maybe find and link the right file for me!?
I have never used the method with flash all bat file, this being said i would really appreciate if you could do me that favor and maybe guide me on how to.
I really love my 4 xl and hate the fact that I have these issues, I have been using it like this for some days hoping a fix will pop out there before I install everything back again.
I sincerely thank you for the effort and time
Click to expand...
Click to collapse
I know it's been 4-5 days since you last responded, but I'm going to assume you still need help. Flashing a full factory image (Not OTA) using the included flash-all.bat script will return your phone to "out of the box" condition. It's a fool proof way to get the phone completely factory stock, so you can then test your hardware (proximity sensor). Instructions can be found on the image download page. It's possible you have a sensor issue, but flashing the full image is the first step. Best of luck and be sure to come back and let us know how it went.
Hello, everyone.
I have a similar issue, though nothing related to the bootloader. I did flash the entire factory image and the process went smoothly until the very end where it showed:
Erasing 'userdata'
Erase successful, but not automatically formatting.
File system type raw not supported.
Erasing 'metadata'
Erase successful, but not automatically formatting.
File system type raw not supported.
Rebooting
Finished. Total time 253.513s
Press any key to exit...
The phone booted up just fine but I can't stop being worried something might eventually not work properly because of this.
Is there anything else I can try?
Rocio19 said:
Hello, everyone.
I have a similar issue, though nothing related to the bootloader. I did flash the entire factory image and the process went smoothly until the very end where it showed:
Erasing 'userdata'
Erase successful, but not automatically formatting.
File system type raw not supported.
Erasing 'metadata'
Erase successful, but not automatically formatting.
File system type raw not supported.
Rebooting
Finished. Total time 253.513s
Press any key to exit...
The phone booted up just fine but I can't stop being worried something might eventually not work properly because of this.
Is there anything else I can try?
Click to expand...
Click to collapse
No. You used the flash-all without removing the -w. That is the reason your userdata was erased. You're good!
Homeboy76 said:
No. You used the flash-all without removing the -w. That is the reason your userdata was erased. You're good!
Click to expand...
Click to collapse
Thank you very much for your reply. My main concern is the part about not being able to format it. Is that normal?
Rocio19 said:
Thank you very much for your reply. My main concern is the part about not being able to format it. Is that normal?
Click to expand...
Click to collapse
Yes! I don't think you'll have any problems.
Homeboy76 said:
Yes! I don't think you'll have any problems.
Click to expand...
Click to collapse
Phew! That's a relief. I just got the phone yesterday and I was so worried I had blessed it up somehow :crying:
Think I'll stay with stock for a while before I attempt any more flashing lol. Thank you!
I got tired of dealing with face unlock being broken and other issues related to the proximity sensor (screen wouldn't light up during a call if i moved it away from my face).
So I decided to flash back to the latest Android 10 image prior to 11 coming out. Everything is back to working buttery smooth.
If anyone else wants to do this and needs help let me know.
A few tips:
I used https://flash.android.com to perform the factory flash
I used this build 10.0.0 (QQ3A.200805.001, Aug 2020)
After flashing, the phone wants you to upgrade to Android 11, but you can enable developer options and turn off Android System Update notifications.
Stock Firmware Packages
Yes, they are finally here! This thread is for stock firmware packages.
These packages are specifically made to be installed with this EDL tool: https://forum.xda-developers.com/ax...n-10-pro-5g-expanded-edl-tools-fixes-t4174667
READ THE WARNINGS IN THAT THREAD BEFORE USING THE TOOLS
These packages are UNOFFICIAL unless marked otherwise. ZTE has not released stock firmware packages for most phones and versions.
How to install an EDL firmware package:
Note: These packages are specifically made for the EDL tools, not MiFlash or anything else.
1. Install the latest version of the EDL tools (in this thread)
2. Download a firmware package from this thread.
3. Unpack the firmware archive into the tool directory "Firmware_Package_Restore"
Make sure you unpack the firmware into Firmware_Package_Restore directory like this -Just for example - the script would be located in:"...\Axon10_(More)_EDL_Tools_v1_1b\Firmware_Package_Restore\Write Firmware v1.10 to A.ps1"And the firmware files would be in:"...\Axon10_(More)_EDL_Tools_v1_1b\Firmware_Package_Restore\firmware_1_10\"4. Put phone in EDL mode and run Load Programmer
5. Run a backup of your phone! Even if it isn't booting.
6. Run whichever "Write Firmware vX to Y.ps1" you want (X = firmware version, Y = A or B partition) (If you don't know which partition is currently booting, just install both.)
7. Wait for the install to finish ("done")
8. Start the phone (hold the power button until it resets, or run the Reset script)
9. You might see a few bootloops and then the phone ask you to do a factory reset / system wipe.
10. If the phone does not boot - look in the tools thread for how to use the Fix Bootable tool and try that.
11. Done.
Firmware Package Downloads:
~~~ A2020U (US Version) (Non-5G) ~~~
Firmware Version: 1.10 (GEN_NA_A2020U_PROV1.10)
Android: 9 (Pie)
Source: UNOFFICIAL (bobthenormal)
Download: Axon10Pro A2020U EDL Firmware v1.10(A9)
(If you downloaded this firmware before 12/9/2020 the script had an error, re-download the firmware or simply replace the script files with these ones: Firmware 1.10 Script Fix)
Thanks:
@djkuz for the original EDL tool for Axon 7
@Unjustified Dev for his port of the tool and tons of other work
@rafyvitto for a ton of ROMs and his stock B12 backup
and @eKeith for requesting the firmware enough times I finally bothered to make it =P
Please keep issues with the firmware here, and issues with the EDL tools in that thread.
I will upload firmware versions for A2020U: 1.11, 1.13, 2.09 (A10) (locked and unlocked). I just need to get time to actually test these out to make sure they work.
I didn't test the 1.10 version either but it should work and some people are stuck on A10 without it so I'm trying to post it quickly.
If anyone can wants the tools or firmware packages like these for their phone version (EU, CN, whatever non-A2020U Non-5G) and can volunteer their phone/time, PM me - I can't do them myself as I don't have those phones, but I can give safe instructions on what to do so that I can change make a version of the tools for those phones.
Hi i want the Firmware for zte axon 10 pro 5g 6ram
Details in photo
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Axon 10 Pro (Non-5G) EDL Tool - Flash / Backup / Restore/ Bootloader Unlock
Axon 10 EDL Tool BAT-program for Flash / Backup / Restore/ Bootloader Unlock Qualcomm HS-USB QDLoader 9008 (COM ...) !!! Whatever you do, you do at your own risk !!!" !!! If you are not sure of yourself do not use this program !!! Special...
forum.xda-developers.com
My post
amooor said:
Hi i want the Firmware for zte axon 10 pro 5g 6ram
Details in photo
View attachment 5146295
Axon 10 Pro (Non-5G) EDL Tool - Flash / Backup / Restore/ Bootloader Unlock
Axon 10 EDL Tool BAT-program for Flash / Backup / Restore/ Bootloader Unlock Qualcomm HS-USB QDLoader 9008 (COM ...) !!! Whatever you do, you do at your own risk !!!" !!! If you are not sure of yourself do not use this program !!! Special...
forum.xda-developers.com
My post
Click to expand...
Click to collapse
I'd suggesta new thread. I haven't seen anyone with that phone or a firmware package for it. If you can find someone that has your phone with stock firmware who is willing to do a little work, I'll tell them what to do to make it.
bobthenormal said:
I'd suggesta new thread. I haven't seen anyone with that phone or a firmware package for it. If you can find someone that has your phone with stock firmware who is willing to do a little work, I'll tell them what to do to make it.
Click to expand...
Click to collapse
Am sure 100% the problem is Firmware.
Do you know why because the holder tray for your ZTE Axon 10 Pro 5g in my phone is making for 1 sim like oneplus 7t in t-mobile if you unlocked and change the holder tray to hybrid dual sim it will work
Hello, I tried to use your tools to restore my phone since its on the European version and my sim card doesn't work (its US). The Write Firmware v1.10 to A tells me that COMPort is not found even though I already launched the load programmer script and see a COMPort file in the folder. Any ideas on what I can do? Thank you for your time!
los95 said:
Hello, I tried to use your tools to restore my phone since its on the European version and my sim card doesn't work (its US). The Write Firmware v1.10 to A tells me that COMPort is not found even though I already launched the load programmer script and see a COMPort file in the folder. Any ideas on what I can do? Thank you for your time!
Click to expand...
Click to collapse
Make sure you unpack the firmware into Firmware_Package_Restore directory like this -
Just for example - the script would be located in:
"...\Axon10_(More)_EDL_Tools_v1_1b\Firmware_Package_Restore\Write Firmware v1.10 to A.ps1"
And the firmware files would be in:
"...\Axon10_(More)_EDL_Tools_v1_1b\Firmware_Package_Restore\firmware_1_10\"
bobthenormal said:
Make sure you unpack the firmware into Firmware_Package_Restore directory like this -
Just for example - the script would be located in:
"...\Axon10_(More)_EDL_Tools_v1_1b\Firmware_Package_Restore\Write Firmware v1.10 to A.ps1"
And the firmware files would be in:
"...\Axon10_(More)_EDL_Tools_v1_1b\Firmware_Package_Restore\firmware_1_10\"
Click to expand...
Click to collapse
Thanks for the response! I will try it on Tuesday as I have finals. Will update to see what happens.
Okay I tried it again with the steps and now its giving me this.
https://pastebin.com/LwbK3vf7
It tells me that it can't find the files even though I have put the folder in that directory. Sorry for being ignorant I thought this wouldn't be too bad since I used to root Samsung devices.
Update:
I downloaded the new version of the edl tools and it still can't find the firmware files. Here is the log.
https://pastebin.com/LRuXEx0y
Another Update:
Sorry for the updates just wanted to see if I can fix it but I figured out why it didn't find the files.
For some reason, it would try to find the files inside the Firmware_Package_Restore instead of its own folder.
Now, I am getting another error that is says that my device is not on the port although I put it in edl mode. Perhaps I am doing something wrong? Here is another log with this error.
https://pastebin.com/ZtXwhUB0
los95 said:
Okay I tried it again with the steps and now its giving me this.
https://pastebin.com/LwbK3vf7
It tells me that it can't find the files even though I have put the folder in that directory. Sorry for being ignorant I thought this wouldn't be too bad since I used to root Samsung devices.
Update:
I downloaded the new version of the edl tools and it still can't find the firmware files. Here is the log.
https://pastebin.com/LRuXEx0y
Another Update:
Sorry for the updates just wanted to see if I can fix it but I figured out why it didn't find the files.
For some reason, it would try to find the files inside the Firmware_Package_Restore instead of its own folder.
View attachment 5152479
Now, I am getting another error that is says that my device is not on the port although I put it in edl mode. Perhaps I am doing something wrong? Here is another log with this error.
https://pastebin.com/ZtXwhUB0
Click to expand...
Click to collapse
Hey! Thanks for attaching the log, that was perfect for finding the issue right away. The script is building the search_path incorrectly, here's corrected copies of the scripts. I'll update and re-upload the full firmware zip file as soon as I get a chance, but just replace the ones you have with these.
EDIT: Ah, yes hold on I'll take a look at the second issue. Sorry about that, didn't have a chance to test these.
So, the new problem appears to be something with the COM port communication. I have to get going in a minute but a few suggestions to try:
Reboot your phone into EDL then run the loader/firmware scripts right away. Sometimes the ports kind of time out.
Open Device Manager in windows and open the "Ports" list and make sure you see your phone on there. Edit the COMPort file to have the right one, or delete it to force the script to re-check if it's trying to connect to the wrong one.
Check the drivers - the tools have the stock A2020U drivers included, might need to reinstall them especially if you install drivers for other phones.
See if any of those help, let me know how it goes.
bobthenormal said:
Hey! Thanks for attaching the log, that was perfect for finding the issue right away. The script is building the search_path incorrectly, here's corrected copies of the scripts. I'll update and re-upload the full firmware zip file as soon as I get a chance, but just replace the ones you have with these.
EDIT: Ah, yes hold on I'll take a look at the second issue. Sorry about that, didn't have a chance to test these.
So, the new problem appears to be something with the COM port communication. I have to get going in a minute but a few suggestions to try:
Reboot your phone into EDL then run the loader/firmware scripts right away. Sometimes the ports kind of time out.
Open Device Manager in windows and open the "Ports" list and make sure you see your phone on there. Edit the COMPort file to have the right one, or delete it to force the script to re-check if it's trying to connect to the wrong one.
Check the drivers - the tools have the stock A2020U drivers included, might need to reinstall them especially if you install drivers for other phones.
See if any of those help, let me know how it goes.
Click to expand...
Click to collapse
Thanks I will try this.
Edit:
I ended up deleting the com port file, ran Load Programmer, and the scripted worked. However, when it finished and I go back to boot my phone (I had to use the other edl tool and asked it to unlock the google FRP since I don't know another method to boot it back to normal) it boot back to the old rom it had. Its like it didn't write anything to the phone although the script did show me it was doing its job and end with a success. Any ideas? Here is my phone with the same firmware still installed after using the script.
Update:
I decided to use the write firmware to b instead and now it is American. Thank you for all the hard work I thought I had to carry two phones with me everywhere lol. Now I have another question. When I reboot my phone, a message pops up saying that the phone is unlocked and to either press the power button to pause or continue. I read in the threads that this means that fast boot is disabled. Is there anyway I can get fast boot back?
los95 said:
Thanks I will try this.
Edit:
I ended up deleting the com port file, ran Load Programmer, and the scripted worked. However, when it finished and I go back to boot my phone (I had to use the other edl tool and asked it to unlock the google FRP since I don't know another method to boot it back to normal) it boot back to the old rom it had. Its like it didn't write anything to the phone although the script did show me it was doing its job and end with a success. Any ideas? Here is my phone with the same firmware still installed after using the script.
View attachment 5153355
Update:
I decided to use the write firmware to b instead and now it is American. Thank you for all the hard work I thought I had to carry two phones with me everywhere lol. Now I have another question. When I reboot my phone, a message pops up saying that the phone is unlocked and to either press the power button to pause or continue. I read in the threads that this means that fast boot is disabled. Is there anyway I can get fast boot back?
Click to expand...
Click to collapse
Nice! Super glad that it worked.
That A/B issue is why I considered just making the script automatically install it to both A and B. The only way I can tell which side is booting is to go into fastboot, which I find annoying. But if you install a ROM to A while you're booting from B, you won't see it obviously, so I generally just flash both sides at the same time since I always have full backups of both anyway.
As for that message, it sort-of means fastboot is disabled - it pops up when:
1. the bootloader is unlocked
AND
2. the stock bootloader is installed
So to get rid of the message you can either re-lock the phone OR install Unjustified Dev's patched bootloader. And since the stock bootloader does not have fastboot, the only way to have it is to install the unlocked bootloader.
You can do that either through the old tool ("unlock" the phone again), or through mine by running "write_UD-bootloader.ps1" in the Write_Unlocked_Bootloader_and_FRP folder.
bobthenormal said:
Nice! Super glad that it worked.
That A/B issue is why I considered just making the script automatically install it to both A and B. The only way I can tell which side is booting is to go into fastboot, which I find annoying. But if you install a ROM to A while you're booting from B, you won't see it obviously, so I generally just flash both sides at the same time since I always have full backups of both anyway.
As for that message, it sort-of means fastboot is disabled - it pops up when:
1. the bootloader is unlocked
AND
2. the stock bootloader is installed
So to get rid of the message you can either re-lock the phone OR install Unjustified Dev's patched bootloader. And since the stock bootloader does not have fastboot, the only way to have it is to install the unlocked bootloader.
You can do that either through the old tool ("unlock" the phone again), or through mine by running "write_UD-bootloader.ps1" in the Write_Unlocked_Bootloader_and_FRP folder.
Click to expand...
Click to collapse
Thanks for the great help. Now I have installed twrp and will most likely just put magisk and keep the stock rom as I am now terrified on installing a custom rom since it lead to me to a lot of trouble. Maybe I will touch lineage later on but for now I will just have twrp and root.
los95 said:
Thanks for the great help. Now I have installed twrp and will most likely just put magisk and keep the stock rom as I am now terrified on installing a custom rom since it lead to me to a lot of trouble. Maybe I will touch lineage later on but for now I will just have twrp and root.
Click to expand...
Click to collapse
You're welcome!
I wouldn't be afraid of doing custom roms once you do a full backup of your working phone with my tools! If you have the 256gb phone you can add the userdata backup to that and really have everything including settings, apps, and data. Then if anything goes wrong you just do a full restore back to exactly where you were.
I haven't been trying custom ROMs because I just don't have the hours to spend trying them out and re-configuring each one to find out which I want to use, otherwise I definitely would. The stock ROM is really kinda poop (I'm on A10).
Also, if you try flashing a custom ROM and it doesn't boot after you install it - before assuming it didn't work and restoring, FIRST try the "Fix bootable" tool. Some ROMs get installed to a different partition than they were made from, so they have that flag for which partition they think they are installed on. When it doesn't match it won't boot. Good luck!
bobthenormal said:
You're welcome!
I wouldn't be afraid of doing custom roms once you do a full backup of your working phone with my tools! If you have the 256gb phone you can add the userdata backup to that and really have everything including settings, apps, and data. Then if anything goes wrong you just do a full restore back to exactly where you were.
I haven't been trying custom ROMs because I just don't have the hours to spend trying them out and re-configuring each one to find out which I want to use, otherwise I definitely would. The stock ROM is really kinda poop (I'm on A10).
Also, if you try flashing a custom ROM and it doesn't boot after you install it - before assuming it didn't work and restoring, FIRST try the "Fix bootable" tool. Some ROMs get installed to a different partition than they were made from, so they have that flag for which partition they think they are installed on. When it doesn't match it won't boot. Good luck!
Click to expand...
Click to collapse
Thanks for the tip! I forgot to mention something strange about the reset from edl tool. When I was turning my phone back to American, I tried to use that and it gave me an error saying this
{ERROR: Command line argument 'reset=' is not recognized as a valid option}
On the shell window it shows different options and there is one that says reset but without = sign. I'm not sure if its some typo but wanted to let you know.
los95 said:
Thanks for the tip! I forgot to mention something strange about the reset from edl tool. When I was turning my phone back to American, I tried to use that and it gave me an error saying this
{ERROR: Command line argument 'reset=' is not recognized as a valid option}
On the shell window it shows different options and there is one that says reset but without = sign. I'm not sure if its some typo but wanted to let you know.
Click to expand...
Click to collapse
Ah that is weird! I must have forgot to save some changes to that script, it's supposed to use the XML file. Fixed that and threw on a script with a long delay ( version 1.1d now)
Thanks for pointing that out.. my quality control guy is slacking! (I'm the quality control guy...)
Lemme know if you find any other ones.
bobthenormal said:
Ah that is weird! I must have forgot to save some changes to that script, it's supposed to use the XML file. Fixed that and threw on a script with a long delay ( version 1.1d now)
Thanks for pointing that out.. my quality control guy is slacking! (I'm the quality control guy...)
Lemme know if you find any other ones.
Click to expand...
Click to collapse
Sorry for all the replies I just want to be sure everything is fine with the backup tool. I did the full back up and it looks like it worked but I was getting warnings that the files it was looking for returned as null. Is that supposed to happen? Here is the link with the log.
backup_all log - Pastebin.com
los95 said:
Sorry for all the replies I just want to be sure everything is fine with the backup tool. I did the full back up and it looks like it worked but I was getting warnings that the files it was looking for returned as null. Is that supposed to happen? Here is the link with the log.
backup_all log - Pastebin.com
Click to expand...
Click to collapse
Oh whew, you scared me if there was a problem with backup_all
That's the one I was especially careful about since I got burned by the original EDL backup tool.
No worries about bringing up potential issues, I can't guarantee the tools don't mess up anyone's phone but I'd still feel terrible if they did so I appreciate the "bug testing".
The warnings there are all good even though they look scary.
If you look in the log, you see the files are attempt to read (and returned NULL) first, then once it has gone through all of them it repeats the list. The way the EDL interface works is kind of odd. It doesn't take a "read" command, it takes a "write" command "reversed", so it executes it like a write command sort of. That means it looks for the files to "write" first to prepare, even though it doesn't actually use them (except to overwrite them if they do exist).
It makes sense from a programming perspective, efficient and saves ROM.
Hi, I am back again. Magisk had an update and after it was installed, the phone wouldn't boot up anymore. It just stayed at the bootloader and I had to wipe it and installed the original firmware as for some unknown reason, my backup is not there. I tried using the restore tool and it couldn't find my back up. I checked the specific files folders to see if the backup was there and nothing was found. The good thing is that the phone can be brought back life even if I have to start fresh ( I don't mind it to be honest since I don't use a lot of apps). This inspired me to install lineage but the link on that thread is broken. Someone asked the OP of the thread about it but I think he hasn't been active for a while. Do you by any chance have the lineage rom file? Sorry for asking but I don't know where to look. Thanks for reading!
los95 said:
Hi, I am back again. Magisk had an update and after it was installed, the phone wouldn't boot up anymore. It just stayed at the bootloader and I had to wipe it and installed the original firmware as for some unknown reason, my backup is not there. I tried using the restore tool and it couldn't find my back up. I checked the specific files folders to see if the backup was there and nothing was found. The good thing is that the phone can be brought back life even if I have to start fresh ( I don't mind it to be honest since I don't use a lot of apps). This inspired me to install lineage but the link on that thread is broken. Someone asked the OP of the thread about it but I think he hasn't been active for a while. Do you by any chance have the lineage rom file? Sorry for asking but I don't know where to look. Thanks for reading!
Click to expand...
Click to collapse
Damn that's not good. You checked in the Backup tool folder for the backups?
They would be named "backup_all-critical-(date/time)" and "backup_all-non-critical-(date/time)"
The Restore tool doesn't automatically try to find backups, you have to move the backup files you want to restore into the restore directories (critical to critical, non-critical to non-critical).
It's not super user friendly, but it's a ton of extra work to make it search for backups and pop up a menu and such. Hopefully that's the issue, but if not I'd like to know if you figure out why the backups aren't there.
I *think* I have the lineage ROM... but I can't upload it right now, on slow internet! Might be a few weeks before I get back, if rafy hasn't uploaded it by then I'll upload it.
Also, the magisk update - I've had that happen on several phones too where it tries to update itself and bricks, so I'm really careful about when I do updates. Not sure if there's a safe method, maybe uninstalling magisk and reinstalling the new version.
.