Database Develop

Problem with ROM UPGRADE under VMWARE /no connection after the Boot Loader menu/

I have a trouble flashing my Diamond ROM with HardSPL or anything else, including the original shipped ROMs. First of all I'm running the WinXP as a guest OS under VMWare and my host is linux. Once the Diamond restart and enter the boot loader (the colorful screen) the XP can't recognize it with the standart message "USB Device Not Recognized"...
The info I receive in dmesg is as follows:
usb 3-2: new full speed USB device using uhci_hcd and address 10
usb 3-2: new full speed USB device using uhci_hcd and address 11
usb 3-2: new device found, idVendor=0bb4, idProduct=0a15
usb 3-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-2: Product: Qualcomm CDMA Technologies MSM
usb 3-2: Manufacturer: HTC
usb 3-2: configuration #1 chosen from 1 choice
Also, of course I have allowed and redirected the "High Qualcomm CDMA Technologies MSM" into VMWare.
Any ideas??
Cheers!!

i have the same prolem..did u manage to sole this problem?

USB serial port not appearing in usb host api

I've installed the latest CyanogenMod build on my Galaxy Tab 8.9. When I connect my pl2303 usb serial port adapter to the device and open the "USB Device Info" app I can only see the device under the "Linux" tab, but not under the "Android" tab. Dmesg says:
Code:
<6>[ 241.823933] tegra-ehci tegra-ehci.0: Tegra EHCI Host Controller
<6>[ 241.824139] tegra-ehci tegra-ehci.0: new USB bus registered, assigned bus number 1
<6>[ 241.832350] [ CONNECTOR_DRIVER (acc_notified,427) ] ACCESSORY=OTG : STATE=online
<6>[ 241.851514] tegra-ehci tegra-ehci.0: irq 52, io mem 0xc5000000
<6>[ 241.871488] tegra-ehci tegra-ehci.0: USB 2.0 started, EHCI 1.00
<6>[ 241.871702] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>[ 241.871728] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 241.871749] usb usb1: Product: Tegra EHCI Host Controller
<6>[ 241.871767] usb usb1: Manufacturer: Linux 2.6.36.4-cyanogenmod+ ehci_hcd
<6>[ 241.871786] usb usb1: SerialNumber: tegra-ehci.0
<6>[ 241.876842] hub 1-0:1.0: USB hub found
<6>[ 241.876888] hub 1-0:1.0: 1 port detected
<6>[ 241.878664] tegra-otg tegra-otg: tegra_start_host-
<6>[ 241.878687] host_notify: ndev name=usb_otg: from state=2 -> to state=1
<6>[ 242.091586] usb 1-1: new full speed USB device using tegra-ehci and address 2
<6>[ 242.321825] usb 1-1: New USB device found, idVendor=067b, idProduct=2303
<6>[ 242.321881] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
<6>[ 242.321926] usb 1-1: Product: USB-Serial Controller D
<6>[ 242.321962] usb 1-1: Manufacturer: Prolific Technology Inc.
Why isn't the Android API recognizing the usb device?

I think you need insmod pl2303.ko. ask for it from your kernel developer
Sent from my GT-P1000 using xda premium

[Q] i8190N UMS mode / linux USB problems

Hi,
I use Arch Linux on my laptop (hp dv6 6030ew), and it's not recognizing my phone through usb port. I mean, there is nothing in output of lsusb, and dmesg gives me this :
Code:
[ 665.895871] usb 2-1: new high-speed USB device number 6 using xhci_hcd
[ 665.910145] usb 2-1: no configurations
[ 665.910159] usb 2-1: can't read configurations, error -22
[ 666.069117] usb 2-1: new high-speed USB device number 7 using xhci_hcd
[ 666.083323] usb 2-1: no configurations
[ 666.083338] usb 2-1: can't read configurations, error -22
[ 666.242357] usb 2-1: new high-speed USB device number 8 using xhci_hcd
[ 666.256622] usb 2-1: no configurations
[ 666.256636] usb 2-1: can't read configurations, error -22
[ 666.415590] usb 2-1: new high-speed USB device number 9 using xhci_hcd
[ 666.429800] usb 2-1: no configurations
[ 666.429814] usb 2-1: can't read configurations, error -22
[ 666.429860] hub 2-0:1.0: unable to enumerate USB device on port 1
I think it's hardware problem, but I'm not really sure, so my real question is :
Can you enable UMS on i8190N?
This is my first post, so forgive my newbieshness. Cheers

Hi, fellow Archer...
The stock firmware on the Samsung Galaxy S III mini does not come with an USB Mass Storage Mode.
The nearest thing would be to use MTP (e.g. libmtp, which is in Arch's 'Extra' Repo.
I myself was unable to get this to work, so i'm transferring files either via FTP (have a Server App on the Phone, ADB push command or Airdroid.
If you somehow get Mass Storage Mode or get MTP to work, let me know!
Kind regards
newbienoobz said:
Hi,
I use Arch Linux on my laptop (hp dv6 6030ew), and it's not recognizing my phone through usb port. I mean, there is nothing in output of lsusb, and dmesg gives me this :
Code:
[ 665.895871] usb 2-1: new high-speed USB device number 6 using xhci_hcd
[ 665.910145] usb 2-1: no configurations
[ 665.910159] usb 2-1: can't read configurations, error -22
[ 666.069117] usb 2-1: new high-speed USB device number 7 using xhci_hcd
[ 666.083323] usb 2-1: no configurations
[ 666.083338] usb 2-1: can't read configurations, error -22
[ 666.242357] usb 2-1: new high-speed USB device number 8 using xhci_hcd
[ 666.256622] usb 2-1: no configurations
[ 666.256636] usb 2-1: can't read configurations, error -22
[ 666.415590] usb 2-1: new high-speed USB device number 9 using xhci_hcd
[ 666.429800] usb 2-1: no configurations
[ 666.429814] usb 2-1: can't read configurations, error -22
[ 666.429860] hub 2-0:1.0: unable to enumerate USB device on port 1
I think it's hardware problem, but I'm not really sure, so my real question is :
Can you enable UMS on i8190N?
This is my first post, so forgive my newbieshness. Cheers
Click to expand...
Click to collapse

USB 3.X xHCI module woes

Hi,
I wanted to try to play around with roms for the P1010 (most are for the P1000, so It's really just me trying to see if I can't do a really bad port), so I downloaded Heimdall, put my P1010 into download mode, and checked to see if Heimdall could find my device. It couldnt, but no wonder it couldn't:
Code:
[ 144.398094] usb 3-3: new high-speed USB device number 7 using xhci_hcd
[ 144.411594] usb 3-3: device descriptor read/8, error -75
[ 144.528102] usb 3-3: device descriptor read/8, error -75
[ 144.790846] usb 3-3: new high-speed USB device number 8 using xhci_hcd
[ 144.804350] usb 3-3: device descriptor read/8, error -75
[ 144.920834] usb 3-3: device descriptor read/8, error -75
[ 145.183559] usb 3-3: new high-speed USB device number 9 using xhci_hcd
[ 145.197101] usb 3-3: device descriptor read/8, error -75
[ 145.313586] usb 3-3: device descriptor read/8, error -75
[ 145.576343] usb 3-3: new high-speed USB device number 10 using xhci_hcd
[ 145.589845] usb 3-3: device descriptor read/8, error -75
[ 145.706346] usb 3-3: device descriptor read/8, error -75
[ 145.809327] hub 3-0:1.0: unable to enumerate USB device on port 3
Well, that makes sense. Heimdall can't detect the device if the kernel has trouble recognising the device. So it looks like the xhci_hcd kernel module is having trouble recognising the device. Doing a little research. I've concluded that all of my USB ports are USBv3 ports because all of my USB ports use the xHCI module. If they were v2, they would use eHCI. Further research suggests that download mode with USBv3.x on linux appears to be buggy at the moment. I found reports of people using Heimdall with USB 3 devices, not working, getting the same error, then plugging it into a USBv2 port and it working.
So I'm sort of stuck at this point. My computer came with all USBv3 ports. Does anyone have experience with USBv3 ports and linux? Have you managed to get it to work with the xHCD module? Is there an alternate module that I can use that works better? Does anyone have any more info on this issue?
Thanks,
Dragos

heimdall problem with xhci-hcd module
i have exactly the same problem (and dmesg-logging) with my GT-P5110 tablet on my asus laptop R704A, with ubuntu 12.10 installed.
heimdall does not detect this tablet.
the xhci-hcd module is in kernel embedded, so i can't blacklist that module.
instead i tried to unbind :
conform: ref: ubuntuforums.org/showthread.php?p=9180298#post9180298
echo -n "XXXX:XX:XX.X" | tee /sys/bus/pci/drivers/xhci_hcd/unbind
but without success.
the mentioned problem does not occur with heimdall on the same laptop with my I9300-smartphone connected.
with ADB i don't have any detect problem with the GT-P5110 and I9300-phone.
--
my GT-5110 and I9300 are working perfectly with heimdall on a laptop with the same ubuntu release, but without a usb3.0 interface.

Just found this thread after searching for exactly the same problem. I'm trying to connect a GT-P5110 to Ubuntu (12.10 as well as 13.04) just like you seem to try. Does anyone know if it works on other systems?

I am having this issue too..
[ 37.151513] usb 1-2: new high-speed USB device number 2 using xhci_hcd
[ 37.167861] usb 1-2: device descriptor read/8, error -75
[ 37.287940] usb 1-2: device descriptor read/8, error -75
[ 37.503921] usb 1-2: new high-speed USB device number 3 using xhci_hcd
[ 37.520265] usb 1-2: device descriptor read/8, error -75
[ 37.640343] usb 1-2: device descriptor read/8, error -75
[ 37.856292] usb 1-2: new high-speed USB device number 4 using xhci_hcd
[ 37.872608] usb 1-2: device descriptor read/8, error -75
[ 37.992803] usb 1-2: device descriptor read/8, error -75
[ 38.208755] usb 1-2: new high-speed USB device number 5 using xhci_hcd
[ 38.225032] usb 1-2: device descriptor read/8, error -75
[ 38.345139] usb 1-2: device descriptor read/8, error -75
[ 38.449017] hub 1-0:1.0: unable to enumerate USB device on port 2
Click to expand...
Click to collapse

I am having the exact same issue trying to root a Galaxy Tab 2 7.0, I too have only v3 USB ports, were you able to figure out a way around this?

My H30-U10 doesn't turn on, just vibrates while screen is off

Hi
I was trying to unlock bootloader of my honor 3c (H30-U10) via SP Flash Tools. When I was connecting my phone without battery to PC via USB after clicking "Download" Button, the device kept vibrating and the connection got disconnected and connected every 3 seconds. The Screen was off during all of this process.
Here is my SP Flash Tool log:
Code:
Connecting to BROM...
Scanning USB port...
Search usb, timeout set as 3600000 ms
[email protected]/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2
[email protected]/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0
[email protected]/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.1
[email protected]/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.1/tty/ttyACM0
vid is 0e8d
device vid = 0e8d
pid is 2000
device pid = 2000
com portName is: /dev/ttyACM0
Total wait time = -1467879144.000000
USB port is obtained. path name(/dev/ttyACM0), port name(/dev/ttyACM0)
USB port detected: /dev/ttyACM0
BROM connected
Downloading & Connecting to DA...
COM port is open. Trying to sync with the target...
Failed to Connect DA: S_BROM_DOWNLOAD_DA_FAIL
Disconnect!
BROM Exception! ( BROM ERROR : S_BROM_DOWNLOAD_DA_FAIL (2004)
[H/W] Fail to download DA to baseband chip's internal SRAM!
[HINT]:
1. There's an cable communication problem between FlashTool and BootROM.
2. Target might be shutdown unexpectedly or target lost power supply.
[ACTION]
1. Try again.
2. Proceed H/W checking in download cable and target side com port.
3. Monitor if power-drop occured in target side.)((ConnectDA,../../../flashtool/Conn/Connection.cpp,127))
and this is my dmesg log:
Code:
[ 3440.213018] usb 1-1.2: new high-speed USB device number 55 using ehci-pci
[ 3440.307101] usb 1-1.2: New USB device found, idVendor=0e8d, idProduct=2000
[ 3440.307104] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3440.307105] usb 1-1.2: Product: MT65xx Preloader
[ 3440.307106] usb 1-1.2: Manufacturer: MediaTek
[ 3440.369300] cdc_acm 1-1.2:1.1: ttyACM1: USB ACM device
[ 3443.146921] usb 1-1.2: USB disconnect, device number 55
[ 3560.113932] usb 1-1.2: new high-speed USB device number 56 using ehci-pci
[ 3560.209002] usb 1-1.2: New USB device found, idVendor=0e8d, idProduct=2000
[ 3560.209005] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3560.209007] usb 1-1.2: Product: MT65xx Preloader
[ 3560.209008] usb 1-1.2: Manufacturer: MediaTek
[ 3560.271453] cdc_acm 1-1.2:1.1: ttyACM0: USB ACM device
[ 3563.563312] usb 1-1.2: USB disconnect, device number 56.
.
.
.
[ 3589.764652] usb 1-1.2: new high-speed USB device number 62 using ehci-pci
[ 3589.859355] usb 1-1.2: New USB device found, idVendor=0e8d, idProduct=2000
[ 3589.859359] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3589.859361] usb 1-1.2: Product: MT65xx Preloader
[ 3589.859363] usb 1-1.2: Manufacturer: MediaTek
[ 3589.921646] cdc_acm 1-1.2:1.1: ttyACM0: USB ACM device
[ 3590.138898] usb 1-1.2: USB disconnect, device number 62
I also tried this with windows with all drivers installed, but I got the exact same result.
After a bunch of tries, now my phone doesn't even turns on. When I press power button with battery inserted, It vibrates every 20 seconds and the screen is always off, too. Connecting it to computer makes the same behavior described above.
So… Is there any way to make it fix? Since I can not access to fastboot mode and SP Flash Tools is not working either?

danialbehzadi said:
Hi
I was trying to unlock bootloader of my honor 3c (H30-U10) via SP Flash Tools. When I was connecting my phone without battery to PC via USB after clicking "Download" Button, the device kept vibrating and the connection got disconnected and connected every 3 seconds. The Screen was off during all of this process.
Here is my SP Flash Tool log:
and this is my dmesg log:
I also tried this with windows with all drivers installed, but I got the exact same result.
After a bunch of tries, now my phone doesn't even turns on. When I press power button with battery inserted, It vibrates every 20 seconds and the screen is always off, too. Connecting it to computer makes the same behavior described above.
Soâ?¦ Is there any way to make it fix? Since I can not access to fastboot mode and SP Flash Tools is not working either?
Click to expand...
Click to collapse
Do adb recognize your phone?!

Not at all. I took my device to Huawei center and they told me it's dead. So, I bought a new phone.
DON'T BY FROM HUAWEI!

danialbehzadi said:
Not at all. I took my device to Huawei center and they told me it's dead. So, I bought a new phone.
DON'T BY FROM HUAWEI!
Click to expand...
Click to collapse
Ahhh too bad :/

The same thing happened to my Samsung , i overcharged it via an unstable source, and the power IC was damaged, if i slid the battery in it would just keep vibrating and flash light turned on, it costed me PKR Rs.1200(USD.12$) to repair it......

Try SP Flashtool again, but with your battery in. Flashing recovery might be your best bet

Fixed your device?

hassanjavaid8181 said:
Fixed your device?
Click to expand...
Click to collapse
No. Threw it away!

danialbehzadi said:
No. Threw it away!
Click to expand...
Click to collapse
thats another way to fix issue