Hi, I recently updated to MIUI 13. At first time it started normally but, when I tried to enter recovery mode, it frozen on bootloop. I don't understand what happened. I sent my phone to service center(2-3 times because I wanted to stay at MIUI 13. But it is bootlooped). Now I have this problem. I tried to install fastboot rom(MIUI 12) with auth bypass via SP flash tool. But there is an error:
STATUS EXT RAM EXCEPTION
IS THERE ANOTHER WAYS TO UNBRICK? OR SHOULD I GIVE IT TO SERVICE CENTER? ALSO, CAN YOU TELL ME HOW MUCH DOES IT'S REAL COST?(Because in first time I payed 10 dollars. Then 5 dollars in 2nd and 3rd times).
THANK YOU
Have you solved your issue if not reply me i also hard bricked by phone(redmi 9 prime(lancelot)) but able to solve yesterday. If you want I think I can help you on this.
sairamallu said:
Have you solved your issue if not reply me i also hard bricked by phone(redmi 9 prime(lancelot)) but able to solve yesterday. If you want I think I can help you on this.
Click to expand...
Click to collapse
Thank you for answering. Yes I could solve it. First I wait till my battery dies and did auth bypass. Then when I flashed rom with spflash tool, it worked. Now I am searching for repair IMEI. Now can't enter to meta mode.
Hey my Redmi 9 prime is stuck in bootloop it not going to recovery mode or not in fastboot mode I tried all the process to fix it but it not work please help me
Shashi69 said:
Hey my Redmi 9 prime is stuck in bootloop it not going to recovery mode or not in fastboot mode I tried all the process to fix it but it not work please help me
Click to expand...
Click to collapse
Hi bro how are you? Well first step is to wait until your phone turns off. Then you need yo download ACT UNLOCK TOOL V2.O. After this, you need to install drivers via buttons above right corner of application. Then you need to hold two volume buttons and connect your phone(But before this you just need to press auth bypass button on the app). Then when sentences appeared, and it was written Auth Bypass OK, you need to press Flash button and locate to scatter file of your device in spflash tool(Your fastboot rom folder(unzipped)/images/MT6768Scatter.txt just something like that). Then choose firmware upgrade option and press download button. Wait some time and it will reboot to your system.
YOUR IMEI and DATA WILL BE ERASED!!!BE CAREFULL.
Related
Plzz help me...
My phone xiaomi mi3 first stuck on bootloop then i tried to flash any rom..
Bt while flashing the phone became off...and when i am turning it onn...then only notification led blinks red 3 times..CWM is also not opening ..plzz help me
plzz ..
Is there any way to flash or xiaomi has fastboot mode? ?! or how to flash through pc????????
plzz tell what should i do..
my phone is INDIAN VERSION
AmanNawaz said:
Plzz help me...
My phone xiaomi mi3 first stuck on bootloop then i tried to flash any rom..
Bt while flashing the phone became off...and when i am turning it onn...then only notification led blinks red 3 times..CWM is also not opening ..plzz help me
plzz ..
Is there any way to flash or xiaomi has fastboot mode? ?! or how to flash through pc????????
plzz tell what should i do..
my phone is INDIAN VERSION
Click to expand...
Click to collapse
dont panic ,
xiaomi has fastboot mode just restrt the phone and press power and vol down you will get into fastboot mode
before that just download the fastboot rom frm here,
http://en.miui.com/thread-14641-1-1.html
after downloading the rom ,download mi flash tool
after downloading everything just put your phone to fastboot mode
install mi flash tool on your pc/lap
just on top left ,you will find browse option
just go to the directory where you have unzipped the rom,chose the file
then connect your phone through usb cable it will get detected if not theres a button called refresh just press it and it will get detected
then just flash the rom, it will hardly take 90 secs to flash
now you have working mi3 with miui rom have fun
Sir can you help me on flashing ..on any social network site...canyou add me on fb
aman.nawaz.71
its a request ..plzzzz
Did you solve your prob? If not, PM me.
Stick on It....plzz anyone help :'(
i have already told you how to do it,why dont you simply follow the steps
Listen to zenr2 and do what he has suggested before hitting panic all over
all the best
Sent from my Nexus 5 using Tapatalk
Thanxx all gyzzzzz.....i have successfully recovered my phone
AmanNawaz said:
Thanxx all gyzzzzz.....i have successfully recovered my phone
Click to expand...
Click to collapse
well thats good now have fun,and don't brick your device again
Thanx ZenR2 ...Bro You are simply just awesome
What is the Solution?
AmanNawaz said:
Thanxx all gyzzzzz.....i have successfully recovered my phone
Click to expand...
Click to collapse
I am happy to know that you got your phone working again, but can you please tell where did you went wrong and what is the solution behind it. So that other's can know about it too.
Regards.
Ask ZenR2
Hey guys, I am in a big fuss here, I was flashing new MIUI MM 6.0 and it was taking to long to flash.. I was very sleepy then and I accidentally fell a sleep. The battery was at 88% when I started doing it. So I guess the flashing must have finished by the time the battery ran out.
Now I have kept it for charging for over 2 hours and it dint turn on. Then I tried going to fastboot or recovery, dint work. Then I connected it to the PC to see if the phone is on but the display is somehow dead and WALLA!!! It gets connected. BUT there is a catch, it now shows me SIX different drives out of which 2 drives I can access. I dont know whats going on! Someone please help me. I have to travel 450 km for service center.
del
same problem bro.. how is your mi3 now?
Looks like partition has messed up. Before flashing that MIUI sh*t were you on extended partition table?
http://forum.xda-developers.com/xiaomi-mi-3/general/guide-instruction-to-restore-mi4-mi3-t3279927
Please see this link, it might help...
anshude1 said:
http://forum.xda-developers.com/xiaomi-mi-3/general/guide-instruction-to-restore-mi4-mi3-t3279927
Please see this link, it might help...
Click to expand...
Click to collapse
same problem here, I flashed SMIUI it says cant mount /dev/block/platform/msm_sdcc,. I just let on that screen, and it displays installing SMIUI system. It finishes but phone died after that.
Now same problem with the OP, no power, no fastboot mode, no recovery, when connect to a pc it displays many Drive windows. Please help.
Now I managed to removed the battery still the same no power.
Help please guys.
i have a perfect solution for this problem....100%working...now u have to flash a fastboot rom using mi flash tool from PC.....u can search it on google or u wanna know exact details then u can mail [email protected]
Faced same problem (soft brick) , steps followed to fix it
Connected to PC to check if the phone is still alive or hard bricked (yep it was , i got a lot of new driver pop ups)
I went through some MIUI forum and understood that MM roms have script which changes partition size over stock partition , hence the soft brick if u flash it in extended partition
Downloaded an old fast boot room (MIUI 7 kitkat) and tried to flash it using MIflash tool , but faced another issue in WIN 10 OS.
To fix it had to install latest qualcomm drivers for MI3 and flashed the rom in Safe mode(win10).
Now you can either flash fastboot rom or recovery zip after you change the recovery.
andy96singh said:
i have a perfect solution for this problem....100%working...now u have to flash a fastboot rom using mi flash tool from PC.....u can search it on google or u wanna know exact details then u can mail [email protected]
Click to expand...
Click to collapse
This is a public forum buddy, people aren't playing hide and seek here. So if you've solution or any tips,please share it here or provide a valid link so the user can get touch with it. Yes, google is everyone's friend, but do not ask the user to send email for solution.
Hello,
I hope anybody could give me a hint a my problem:
When booting my ZUK Z2 Pro it appears a menu which cannot be left.
It is not possible to boot into fastboot mode or recovery mode, I´ve tried to boot a stock ROM with QFIL which was succesful but after reboot the bootet in the mentiones menu again. In the menu I could only scroll but not touch any button.
Has anybody an idea what I could do?
A picture of the menu is attached.
Thanks for any support!
Had the same problem as you had, only solution is: Never touch this menu again after flashing Nougat. This is what I replied to the zukfans forum:
Yes, I successfully unbricked it, works like its first day of purchase. Problem is I don't really know how.
The things I remember right now is:
letting the battery drain until phone shuts off (the power off trick (holding the power button) didn't work for me)
reading this guide and following step by step https://www.gizmochina.com/2016/08/24/zuk-z2-z2-pro-rom-flashing-guide/
realizing my phone got bricked and panicking
reading this guide: http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
installing the correct divers
connecting to PC via QFIL and trying to flash the firmware (it got detected as a 9008 device at first try, pretty awesome)
smashing my head to the table because of a bricked phone and "Download Fail: Sahara Fail:QSaharaServer Fail: Process Fail"
letting the battery drain for 5 days (I had an emergency Sony Xperia Z3 Compact with me and wasn't at home)
trying again to connect to PC via QFIL
flashing again and dancing around my room because the rom got flashed successfully
So it could have been sheer luck or anything else... I really don't know
Click to expand...
Click to collapse
Good Luck reviving your phone from the pesky Nougat Test Menu...
yomama163 said:
Had the same problem as you had, only solution is: Never touch this menu again after flashing Nougat. This is what I replied to the zukfans forum:
Good Luck reviving your phone from the pesky Nougat Test Menu...
Click to expand...
Click to collapse
Thanks a lot. It worked after several trials.
Hi All,
I have L19-C636B190 and trying to update to B361 was unsuccessful, so i went through different forums and past post for alternative and downloaded the B320 update somewhere.
Installed via the 3 keys method and failed around 40% and now my phone is bricked
connected to Hisuite to see if i can do a restore it said my phone is not supported...
I cannot use the vol - + power method to flash to another rom.
I can only boot into fastboot by doing Vol - & Power.
I haven't unlocked it, it was on L19-C636B190
PHONE Locked
FRP Lock
i've looked everywhere still no luck...
Please help me here
I have same problem. Ill folow This tread
Only solution is DC phoenix. You will have to pay a bit but its possible to fix it. Maybe you can try to push everything through ADB as well. Read the forum and try to follow the procedures.
calvin27 said:
Hi All,
I have L19-C636B190 and trying to update to B361 was unsuccessful, so i went through different forums and past post for alternative and downloaded the B320 update somewhere.
Installed via the 3 keys method and failed around 40% and now my phone is bricked
connected to Hisuite to see if i can do a restore it said my phone is not supported...
I cannot use the vol - + power method to flash to another rom.
I can only boot into fastboot by doing Vol - & Power.
I haven't unlocked it, it was on L19-C636B190
PHONE Locked
FRP Lock
i've looked everywhere still no luck...
Please help me here
Click to expand...
Click to collapse
I assume you dont know your unlock code, am I right? Because if you did, you could unlock via fastboot, flash custom recovery and try anything. But I think you dont have that..
I was send my Phone to waranty i hope they can solve it.
After a few thread in regards to DC Phoenix. I decided to bite the bullet and paid them 15Euro and see if it can unbrick my phone and update to Nougat C636B390 while I'm using it.
IT WORKED!
I'm now on L19C636B390... I'll post my method here on how to unbrick it tomorrow...
Thanks to Xda forums and hopefully my thread will able to help some others who are (was) in the same boat with me...
Told ya enjoy!
Hello everyone, everything good ? I would like to know if you could help me I bought a OnePlus ACE 5G (PGKM10) I followed a tutorial here on the forum on how to root using Magisk and patching boot.img, I tried a few times and the device was in bootloop with the OnePlus logo and when I started the system crashed and restarted.
But after trying to patch again, I saw that when it started, the image was horrible as if it had a video problem there, it crashed and restarted again.
I tried to fix the error by doing another patch procedure and now the cell phone does not turn on anymore nor does the image appear, if you hold the power button and try to turn it on it just vibrates, the same happens if you try to enter fastboot windows beeps that it has detected a device and soon after it disconnects.
Could anyone shed some light on how to get it working again?
darklegends2008 said:
Hello everyone, everything good ? I would like to know if you could help me I bought a OnePlus ACE 5G (PGKM10) I followed a tutorial here on the forum on how to root using Magisk and patching boot.img, I tried a few times and the device was in bootloop with the OnePlus logo and when I started the system crashed and restarted.
But after trying to patch again, I saw that when it started, the image was horrible as if it had a video problem there, it crashed and restarted again.
I tried to fix the error by doing another patch procedure and now the cell phone does not turn on anymore nor does the image appear, if you hold the power button and try to turn it on it just vibrates, the same happens if you try to enter fastboot windows beeps that it has detected a device and soon after it disconnects.
Could anyone shed some light on how to get it working again?
Click to expand...
Click to collapse
Try EDL method bro
Junel Ortiz 🇵🇭 said:
Try EDL method bro
Click to expand...
Click to collapse
I tried to boot pressing volume up and down but nothing happens on windows, i will give a search in how to put my device in EDL mode again.
Thanks bro
darklegends2008 said:
I tried to boot pressing volume up and down but nothing happens on windows, i will give a search in how to put my device in EDL mode again.
Thanks bro
Click to expand...
Click to collapse
Welcome bro. I think that's the final to survive your device. Hope always good bro. Good luck ..
Junel Ortiz 🇵🇭 said:
Welcome bro. I think that's the final to survive your device. Hope always good bro. Good luck ..
Click to expand...
Click to collapse
Hi!
How are you ?
I tried to enter EDL mode but without success, I think it's with HardBrick, making the button combinations the only thing that happens is vibrating, although windows recognize a new device after a few seconds it disconnects.
I have no way to send it to OnePlus.
Is there anything else I can do to resolve this?
darklegends2008 said:
Hello everyone, everything good ? I would like to know if you could help me I bought a OnePlus ACE 5G (PGKM10) I followed a tutorial here on the forum on how to root using Magisk and patching boot.img, I tried a few times and the device was in bootloop with the OnePlus logo and when I started the system crashed and restarted.
But after trying to patch again, I saw that when it started, the image was horrible as if it had a video problem there, it crashed and restarted again.
I tried to fix the error by doing another patch procedure and now the cell phone does not turn on anymore nor does the image appear, if you hold the power button and try to turn it on it just vibrates, the same happens if you try to enter fastboot windows beeps that it has detected a device and soon after it disconnects.
Could anyone shed some light on how to get it working
Click to expand...
Click to collapse
Is your issue resolved?
yashaswee1708 said:
Is your issue resolved?
Click to expand...
Click to collapse
Not, still trying to fix the issue.
darklegends2008 said:
Not, still trying to fix the issue.
Click to expand...
Click to collapse
Did you used your current ColorOS version's boot img? Or from where you got the boot.img?
Received help from an engineer from India.
+91 70174 26154 WhatsApp
Symptoms are cyclic loading, goes into Recovery and is displayed in computer devices in BROM mode for a couple of seconds.
Called in and got it done in 10 minutes.
mrkorus said:
Received help from an engineer from India.
+91 70174 26154 WhatsApp
Symptoms are cyclic loading, goes into Recovery and is displayed in computer devices in BROM mode for a couple of seconds.
Called in and got it done in 10 minutes.
Click to expand...
Click to collapse
Which tool did you used to unbrick? or did you got your device fixed remotely?
yashaswee1708 said:
Did you used your current ColorOS version's boot img? Or from where you got the boot.img?
Click to expand...
Click to collapse
Both but none worked
mrkorus said:
Received help from an engineer from India.
+91 70174 26154 WhatsApp
Symptoms are cyclic loading, goes into Recovery and is displayed in computer devices in BROM mode for a couple of seconds.
Called in and got it done in 10 minutes.
Click to expand...
Click to collapse
Sounds exact like my device, how is done the fix ?
darklegends2008 said:
Sounds exact like my device, how is done the fix ?
Click to expand...
Click to collapse
I think you'll have to contact the mentioned person, he'll give you the software. He'll login remotely and flash the firmware. He'll charge you for it.
mrkorus said:
Received help from an engineer from India.
+91 70174 26154 WhatsApp
Symptoms are cyclic loading, goes into Recovery and is displayed in computer devices in BROM mode for a couple of seconds.
Called in and got it done in 10 minutes.
Click to expand...
Click to collapse
@xCadbury Try this maybe.
yashaswee1708 said:
I think you'll have to contact the mentioned person, he'll give you the software. He'll login remotely and flash the firmware. He'll charge you for it.
Click to expand...
Click to collapse
All right. Connected remotely through the UltraViewer program. He checked that the phone is at least somehow determined, then asked to pay for the service. I downloaded everything from my own google drive links. Installed, opened the program under your username and password and set everything up. Waited for the unlock key from the server. Sometimes the key did not come and he sent requests again. As the key came, the ColorOS firmware was immediately installed