Question Xperia 10 IV blinking red light - Sony Xperia 10 IV

My English is not good, so I used Google Translate. I have a xperia10iv engineering prototype. I switched its firmware slot to b by mistake. Now it cannot start normally. The specific performance is that the screen cannot be turned on. When it is connected to the computer, the red light is on, which can be recognized. to the device on port 9008. Is there any way to salvage it?I can't get to green light or blue light mode now (long press volume up/minus to connect usb)

kunkun0897 said:
My English is not good, so I used Google Translate. I have a xperia10iv engineering prototype. I switched its firmware slot to b by mistake. Now it cannot start normally. The specific performance is that the screen cannot be turned on. When it is connected to the computer, the red light is on, which can be recognized. to the device on port 9008. Is there any way to salvage it?I can't get to green light or blue light mode now (long press volume up/minus to connect usb)
Click to expand...
Click to collapse
I doubt its possible if you can't get to blue light mode

King081 said:
I doubt its possible if you can't get to blue light mode
Click to expand...
Click to collapse
I haven't found a way to get into Blu-ray mode yet, but it seems to restart properly, and if I connect to the computer by holding down the volume and power buttons for a while it will disconnect and reconnect after a while

Related

One stuck on, wont soft reboot- home and return flashing

I think I was holding down the power while it was locked. it didnt reboot bus is now instead stuck with a black backlit display panel. home and return is on permanently and the charge light is also lit, despite not being plugged in.
holding down te power button for any length of time just makes the home and return flash for a minute and then back to solid.
no combination of power and volume up/down makes any difference. just flashing home and return lights.
HELP
do I just have to wait for the battery to run out?
Wait I'm a bit confused ...what current state is your phone in? Is it booted up if it is just adb that *****
a box of kittens said:
Wait I'm a bit confused ...what current state is your phone in? Is it booted up if it is just adb that *****
Click to expand...
Click to collapse
it was booted up. now it's just a dark screen with backlight, home and return buttons and charge light lit
plugging in USB and runningg adb reboot just says device not found
actually- when I plug it into USB it appears as in device manager for a few seconds
adb reboot during that period gives 'device offline' rather than device not found...

Does Green /any colour of the notification LED light up in 'Flashtool' mode?

I've noticed this peculiarity in my Sony Xperia Z (C6602), while flashing / upgrading using SUS or flashtool:
1. Vol up & USB insert (with phone switched off) => fastboot mode, flashtool recognises, and notification LED lights up blue. All seems ok....
2. Vol down & USB insert (with phone switched off) => flashtool mode, flashtool recognises, and win7 PC shows Sony device connected in S1 mode, but there is no notification LED light. If my memory serves me right, on the X10i and ST15i, the LED used to light up green.
My question is: is this "No Lights" behaviour normal? Flash takes place beautifully and phone works well, no problems, and I'd like to know if all of you face the same? If not, can I take the phone to Sony service to have this rectified/repaired/replaced (I live in India)? Thanks in advance.....
Dead Cookies leave no trails...
Cookie Ninja said:
I've noticed this peculiarity in my Sony Xperia Z, while flashing / upgrading using SUS or flashtool:
1. Vol up & USB insert (with phone switched off) => fastboot mode, flashtool recognises, and notification LED lights up blue. All seems ok....
2. Vol down & USB insert (with phone switched off) => flashtool mode, flashtool recognises, and win7 PC shows Sony devicen connected in S1 mode, but there is no notification LED light. If I remember, on the X10 and ST15I, the LED used to light up green.
My question is: is this "No Lights" behaviour normal? Flash takes place beautifully and phone works well, no problems, and I'd like to know if all of you face the same? If not, can I take the phone to Sony service to have this rectified/repaired/replaced (I live in India)? Thanks in advance.....
Dead Cookies leave no trails...
Click to expand...
Click to collapse
Yes, mine does the same. I'd assume it's normal.
In my case just after connecting to usb in flashmode shows red led but quickly disappears
The led will blink green and disappear in flash mode.
Sent from my C6603 using xda premium

[Q] Unrooted/stock HTC One bricked?

So my HTC ran out of battery last night, and I left it overnight to charge (red light was showing up).
So I turn it on this morning, and nothing happens. I unplug it from charger and red light is still on, and when I held down powerbutton the home and back buttons would blink, but phone would not come on.
So I read online and tried the home+vol button trick under a bright light and the red light did go away, but nothing else happened.
Now when I press power button nothing happens, not even the home/back button come up.
When I plug it in to the computer I see a driver for QHUSB_DLOAD failing to load. And if I hold down power button and volume while connected to PC, I can hear it "unplugging and replugging" noise from pc.
So is my phone bricked? This was NOT rooted, it was simply the stock device.
I really just want the pictures I have on there, is there any way to get that data back?
QHUSB_DLOAD is related to the boot partition of your phone and is an extremely tricky driver to find. If, for whatever reason, that driver is buggered, your phone may be bricked. As you haven't rooted there really isn't much you can do past try a USB jig or shine a light at the light sensor (two black circles on the front) whilst you try and turn it on. On the bright side though, you should be able to get a relatively easy replacement.
postfatal said:
QHUSB_DLOAD is related to the boot partition of your phone and is an extremely tricky driver to find. If, for whatever reason, that driver is buggered, your phone may be bricked. As you haven't rooted there really isn't much you can do past try a USB jig or shine a light at the light sensor (two black circles on the front) whilst you try and turn it on. On the bright side though, you should be able to get a relatively easy replacement.
Click to expand...
Click to collapse
Where can I get a USB jig for a tmobile htc one?

[Q]HOW TO RECOVER A HARD Bricked Sony XZC6002?

This is a HARD Bricked phone that first started going berserk after a partial install of a SONY software update. The phone would flash the home screen and continually vibrate. I forced it down with power off. Did not know what I was doing and believe I converted a soft brick to a hard brick. The soft brick at first responded to power button and volume up button to reboot. After that point it became more and more unresponsive to complete death.
It is not recognized by PC (even in the device manager) when plugged into USB port on PC. NO LED or any lights on the phone at all! No red charging LED with charger plugged in, No Sony screen icon, no vibration with power button pushed hard for >10 seconds (with and without pushing up/down volume). The ONLY response I get is an audible windows sound coming from my PC as long as I hold the power and volume up button down.
I have left the phone off a charger for >48 hours and then placed it on the charger for 6-7 hours. Still no red LED while on the phone was on the charger. Reason for me doing this was my reading notes that Sony had a battery error issue that could only be solved by removing the battery or draining it completely. Recharging the battery was suppose to be a fix. A recent poster did this (removed the battery) which is a job and was able to get a red LED but nothing else. There was no reply.
My readings also indicated that there are a number of people with this problem (hard bricked phone) involved with download or install of their software Sony reportedly has a fix to install to correct it. I am a day late and a dollar short.
BTW, the Sony PC companion works up until I connect the phone to the PC and then an error message appears to make sure battery is charged to 80% before proceeding. Ignoring that brings up a troubleshooting screen prompting holding the power button and volume up button for 10 seconds. This is where I get an audible windows connect/disconnect sound coming from my PC that will keep sounding as long ass I hold the buttons down and stops after I remove them. Could this possibly be just a battery issue? Any help is greatly appreciated.
jorthodoc said:
This is a HARD Bricked phone that first started going berserk after a partial install of a SONY software update. The phone would flash the home screen and continually vibrate. I forced it down with power off. Did not know what I was doing and believe I converted a soft brick to a hard brick. The soft brick at first responded to power button and volume up button to reboot. After that point it became more and more unresponsive to complete death.
It is not recognized by PC (even in the device manager) when plugged into USB port on PC. NO LED or any lights on the phone at all! No red charging LED with charger plugged in, No Sony screen icon, no vibration with power button pushed hard for >10 seconds (with and without pushing up/down volume). The ONLY response I get is an audible windows sound coming from my PC as long as I hold the power and volume up button down.
I have left the phone off a charger for >48 hours and then placed it on the charger for 6-7 hours. Still no red LED while on the phone was on the charger. Reason for me doing this was my reading notes that Sony had a battery error issue that could only be solved by removing the battery or draining it completely. Recharging the battery was suppose to be a fix. A recent poster did this (removed the battery) which is a job and was able to get a red LED but nothing else. There was no reply.
My readings also indicated that there are a number of people with this problem (hard bricked phone) involved with download or install of their software Sony reportedly has a fix to install to correct it. I am a day late and a dollar short.
BTW, the Sony PC companion works up until I connect the phone to the PC and then an error message appears to make sure battery is charged to 80% before proceeding. Ignoring that brings up a troubleshooting screen prompting holding the power button and volume up button for 10 seconds. This is where I get an audible windows connect/disconnect sound coming from my PC that will keep sounding as long ass I hold the buttons down and stops after I remove them. Could this possibly be just a battery issue? Any help is greatly appreciated.
Click to expand...
Click to collapse
Firstly, you've made one major mistake when you've turned off your phone by using force. It can completely brick your phone forever.
Secondly, if you can hear any sound when connect your phone to USB, then thats mean, that your phone is still in minimal functionality. However, you can give a try to buy a new battery and see, how it goes.
It's better to buy extra battery, than change the whole phone, am I right?
And try to leave your phone without touching it for couple days I think. Maybe your battery somehow has got any fault or it has been faulted when you've force-shutted the phone.
Just give a try and that's all. You can't do anything else, except if you know and you're ready for phone disassembly. If none of my suggested methods will work, then try some other tutorials, you can search for them in XZ category's. I've forgotten how that thread is named, but you can search by some key-words, like : ultimate recovery, back to life, unbrick and etc.,
I hope my information is all correct and helpful, if not, then sorry for disturbation for nothing
LaurynasVP said:
Firstly, you've made one major mistake when you've turned off your phone by using force. It can completely brick your phone forever.
Secondly, if you can hear any sound when connect your phone to USB, then thats mean, that your phone is still in minimal functionality. However, you can give a try to buy a new battery and see, how it goes.
It's better to buy extra battery, than change the whole phone, am I right?
And try to leave your phone without touching it for couple days I think. Maybe your battery somehow has got any fault or it has been faulted when you've force-shutted the phone.
Just give a try and that's all. You can't do anything else, except if you know and you're ready for phone disassembly. If none of my suggested methods will work, then try some other tutorials, you can search for them in XZ category's. I've forgotten how that thread is named, but you can search by some key-words, like : ultimate recovery, back to life, unbrick and etc.,
I hope my information is all correct and helpful, if not, then sorry for disturbation for nothing
Click to expand...
Click to collapse
My gut tells me that the battery is OK but needs to be recharged. Apparently there is something that will not allow the battery to recharge unless it is removed or drained to zero. I thought I drained it to zero but perhaps not. The other case where the battery was removed and was then able to show a red LED apparently allowed the battery to recycle. That's as far as he got.
In the mean time I'm taking your advise and just letting the phone sit until someone makes a suggestion or I get tired of looking at it.
Thank you for your time and suggestions.
Can you enter the "fastboot" mode (unlocked bootloader) /"flash mode" (locked bootloader) ?
Hold "volume down" button and connect with USB cable to the pc.
So first hold "volume down" button and then connect with USB cable to the pc while holding the "volume down" button. Let go the "volume down" when a green led on your phone appears.
You can still enter the "flash mode" if the green led appears.
Hold "volume up" button and connect with USB cable to the pc.
So first hold "volume up" button and then connect with USB cable to the pc while holding the "volume up" button. Let go the "volume up" when a blue led on your phone appears.
If the blue led appears on your phone you can still enter the "fastboot mode".
There is still hope if the green/blue leds appear on your phone (meaning you can still enter "flash mode" / "fastboot mode".
. But the following question need to be answered:
Has your phone an unlocked bootloader?
Sent from my Xperia Z using XDA Free mobile app
pow3rflow3r said:
Can you enter the "fastboot" mode (unlocked bootloader) /"flash mode" (locked bootloader) ?
Hold "volume down" button and connect with USB cable to the pc.
So first hold "volume down" button and then connect with USB cable to the pc while holding the "volume down" button. Let go the "volume down" when a green led on your phone appears.
You can still enter the "flash mode" if the green led appears.
Hold "volume up" button and connect with USB cable to the pc.
So first hold "volume up" button and then connect with USB cable to the pc while holding the "volume up" button. Let go the "volume up" when a blue led on your phone appears.
If the blue led appears on your phone you can still enter the "fastboot mode".
There is still hope if the green/blue leds appear on your phone (meaning you can still enter "flash mode" / "fastboot mode".
. But the following question need to be answered.
It is HARD Bricked. Unresponsive to all of the above w/o any LED response.
Has your phone an unlocked bootloader?
The phone was purchased from Sony and was factory unlocked. It was running fine until the new update from Sony was installed. I believe the update was related to the OS which is 4.4.4.
Thank you.
Sent from my Xperia Z using XDA Free mobile app
Click to expand...
Click to collapse
It is HARD Bricked. Unresponsive to all of the above w/o any LED response.
Has your phone an unlocked bootloader?
The phone was purchased from Sony and was factory unlocked. It was running fine until the new update from Sony was installed. I believe the update was related to the OS which is 4.4.4.
Thank you.

[Q] Xperia Z1 Dead

My phone is not turning on... when I plug in my charger sony logo appears and battery symbol comes but when i tried to turn it on red led blinks and also it vibrates 3 times and again sony logo and battery symbol comes
When i pug into my pc i hear device connected sound in my pc and there is blue led glowing in my phone but agian when i try to turn it on it vibrates three times and agian blue led is glowing please help me to get my phone working back normal
thanks in advance...
harsha1996 said:
My phone is not turning on... when I plug in my charger sony logo appears and battery symbol comes but when i tried to turn it on red led blinks and also it vibrates 3 times and again sony logo and battery symbol comes
When i pug into my pc i hear device connected sound in my pc and there is blue led glowing in my phone but agian when i try to turn it on it vibrates three times and agian blue led is glowing please help me to get my phone working back normal
thanks in advance...
Click to expand...
Click to collapse
First disconnect everything from phone and then press power+volume up button untill 3 vibration then connect charger overnight then try to turn it on next morning...
As I can see
Your volume up button( or maybe down) is stok
Try press them many times in order to fix them.
Then try to turn on your phone again
kathanpatel1001 said:
First disconnect everything from phone and then press power+volume up button untill 3 vibration then connect charger overnight then try to turn it on next morning...
Click to expand...
Click to collapse
When i press power+vol up my phone doesnot respond for it.... no led blinking or vibrating while using the above method...
my phone got this state for using it in pool my indicators became red i know that there will be no warranty if the indicators become red....so help in getting my phone back to work as normal....
.plz help mee....thnks in advance
harsha1996 said:
When i press power+vol up my phone doesnot respond for it.... no led blinking or vibrating while using the above method...
my phone got this state for using it in pool my indicators became red i know that there will be no warranty if the indicators become red....so help in getting my phone back to work as normal....
.plz help mee....thnks in advance
Click to expand...
Click to collapse
Is it completely dry and if it is then do you see sony logo or blue led notification?if sony logo shows up try flashing stock ftf via flash tool
And if blue notification then try to unblock volume up button i thing it is stuck so it puts your phone to fastboot mode when connected to pc hence blue led and when you try to turn on your phone without connecting to pc it hard reset your phone hence three vibration and phone shuts down...
Try unblocking volume up button by pressing hard volume up button many times then connecting to pc until there is no blue light turning on...and after unblocking the button try flashing stock ftf via flash tool...
Be careful not to press it too hard or you will damage your phone..!!
Get phone working again and get it replaced if under warranty to avoid future problems...
kathanpatel1001 said:
Is it completely dry and if it is then do you see sony logo or blue led notification?if sony logo shows up try flashing stock ftf via flash tool
And if blue notification then try to unblock volume up button i thing it is stuck so it puts your phone to fastboot mode when connected to pc hence blue led and when you try to turn on your phone without connecting to pc it hard reset your phone hence three vibration and phone shuts down...
Try unblocking volume up button by pressing hard volume up button many times then connecting to pc until there is no blue light turning on...and after unblocking the button try flashing stock ftf via flash tool...
Be careful not to press it too hard or you will damage your phone..!!
Get phone working again and get it replaced if under warranty to avoid future problems...
Click to expand...
Click to collapse
when i connect my phone to pc blue light is comming....i used sony pc companian and i selected repair my phone it deteced my phone and completed the update but the phone is still in same position not switching
harsha1996 said:
when i connect my phone to pc blue light is comming....i used sony pc companian and i selected repair my phone it deteced my phone and completed the update but the phone is still in same position not switching
Click to expand...
Click to collapse
It may be stuck volume up button it takes your phone to fastboot mode try to free your stuck vol up button...:thumbup:

Categories

Resources