Related
Hello, my watch R has 5.1.1 (LDZ22D) stock ROM and it has some problems. I tried factory reset, still not ok. I would like to try flashing again the stock ROM. I have found this thread: http://forum.xda-developers.com/g-watch-r/development/stock-boot-recovery-g-watch-r-t2956964 , i downloaded boot.img, recovery.img and system.img, checked SHA1 but i don't know which version should i try? 5.1.1 (LDZ22D), 5.1.1 (LCA44B), 5.0.2: ??? Are there limitations for downgrade / upgrade ?
And as a guide to flashing...
1. i start watch, swype 11 to 5, so now in fastboot mode i connect to PC, the PC detect the watch as what ?
2. adb devices and if watch is detected i continue.
3. fastboot flash boot boot.img
4. fastboot flash recovery recovery.img
5. fastboot flash system system.img
6. restart
is that ok ?
How long does it take to flash each of those imgs ?
thank you
intersectRaven said:
Notes/FAQ:
1.) I re-mkbootimg-ed them since I'll be uploading 2 x 20+MB files if I didn't. Still has the same SHA1 checksums as the ones being checked by stock ROM so it's safe to flash.
2.) If you're confused on how to download click on the box marked in this pic.
3.) The commands for flashing are as follows:
Boot: fastboot flash boot boot.img
Recovery: fastboot flash recovery recovery.img
System: fastboot flash system system.img
*replace boot.img, recovery.img and system.img with their respective filenames
**how to obtain the fastboot executables and drivers are explained in a separate thread
4.) The system.img provided above are stock and NOT ROOTED. If you want to go completely stock, just flash ALL the 5.0.1 images above.
*only for 5.0.1 since I didn't make a system image for 4.4W.2 or below
Click to expand...
Click to collapse
took that from the link you posted, just conect the watch to the dock while in fastboot mode, search for 15 second adb/fastboot installer, after installing that and the computer detects your watch just follow those steps using cmd and navigating to the directory where the files are at first, remember to install fastboot and adb system wide on the 15 second adb installer
when in fastboot mode the watch is not detected:
C:\Users\user>adb devices
List of devices attached
when i chose "recovery" in fastboot mode (android robot on back with door open and red exclamation mark) i get:
C:\Users\user>adb devices
List of devices attached
410KCHserialnr888 sideload
but the watch says he waits "adb sideload <filename>"
what i am doing wrong ? something else had to be done ?
thank you
you can use adb to boot watch on bootloader, but it is not needed since you can boot into fastboot already, problem is the watch is not detected on fastboot mode, try finding some drivers or something, what i usually do is download cydia impactor and select usb then let it do the driver stuff for me, quote me next time so i can get notified when you respond
Things are changing with the advent of project treble and seamless updates. OnePlus will no longer release ROMs flashable via recovery (either stock or twrp) because is no more needed. The updates will be done on the slot not used for example if you are using slot a the update will be installed on slot b and the slot b will be set as default. If you brick and you are in bootloop how you can restore the rom? You can't with Stock ROM you have, because the zip can be only installed via Update Engine, so what can you do? Flash a stock rom via fastboot. I have extracted all images from the stock zip and i have made a new zip with the Fastboot ROM with a flash-all.bat included. This will work only if your bootloader is unlocked. This will erase all your data and will wipe your internal storage.
HOW TO FLASH
This version is only for not branded devices
Download the zip;
Unpack the zip in a folder;
Reboot the OnePlus 6T in fastboot mode (Power and volume-);
Connect the OnePlus 6T to PC;
Run flash-all.bat flasher you need;
Wait until the process end;
The phone will automatically reboot.
FLASHER ADVANCED GUIDE
flash-all-partitions-fastboot.bat : this .bat will flash all possible partitions through fastboot (Except persist) , there are some criticals partitions that can't be flashed through fastboot;
flash-only-persist.bat : this .bat will flash only persist partition in fastboot mode (This is good for people that have problems with sensor);
flash-all-partitions-recovery-criticals.bat : this .bat will boot the twrp and will flash criticals partitions, use this carefully;
flash-system-boot-vendor.bat : this .bat is the same of older flash-all.bat and so it will flash only vendor, system and boot;
flash-all-partitions.bat : this .bat will run flash-all-partitions-fastboot.bat , then flash-only-persist.bat and then flash-all-partitions-recovery-criticals.bat .
Now usually the one needed is only the first "flash-all-partitions-fastboot.bat" but if you are badly bricked i recommend to use flash-all-partitions.bat .
DOWNLOAD
All roms on AFH: https://www.androidfilehost.com/?w=files&flid=284914
All roms on Sourceforge: https://sourceforge.net/projects/fastbootroms/files/OnePlus 6T
BRANDED PHONE
GUIDE: https://forum.xda-developers.com/on...-t-mobile-oneplus-6t-to-t3865966/post78131430
T-Mobile OnePlus 6T Internationa ROM: https://www.androidfilehost.com/?fid=11410963190603845445
MANUAL FLASH: Windows - OSX - Linux
If you want to manual flash these roms these are the commands (you need to extract images.zip before proceed)
Fastboot Partitions:
Code:
fastboot flash aop_a aop.img
fastboot flash aop_b aop.img
fastboot flash bluetooth_a bluetooth.img
fastboot flash bluetooth_b bluetooth.img
fastboot flash boot_a boot.img
fastboot flash boot_b boot.img
fastboot flash dsp_a dsp.img
fastboot flash dsp_b dsp.img
fastboot flash dtbo_a dtbo.img
fastboot flash dtbo_b dtbo.img
fastboot flash fw_4j1ed_a fw_4j1ed.img
fastboot flash fw_4j1ed_b fw_4j1ed.img
fastboot flash fw_4u1ea_a fw_4u1ea.img
fastboot flash fw_4u1ea_b fw_4u1ea.img
fastboot flash modem_a modem.img
fastboot flash modem_b modem.img
fastboot flash oem_stanvbk oem_stanvbk.img
fastboot flash qupfw_a qupfw.img
fastboot flash qupfw_b qupfw.img
fastboot flash storsec_a storsec.img
fastboot flash storsec_b storsec.img
fastboot flash system_a system.img
fastboot flash system_b system.img
fastboot flash vbmeta_a vbmeta.img
fastboot flash vbmeta_b vbmeta.img
fastboot flash vendor_a vendor.img
fastboot flash vendor_b vendor.img
fastboot flash LOGO_a LOGO.img
fastboot flash LOGO_b LOGO.img
If you need also persist partition, this is the command:
Code:
fastboot flash persist persist.img
Criticals Partitions, for these you need to boot the TWRP:
Code:
fastboot boot TWRP.img
When you are in TWRP you need to run these commands to push and flash all criticals partitions:
Code:
adb push abl.img /sdcard/abl.img
adb shell dd if=/sdcard/abl.img of=/dev/block/bootdevice/by-name/abl_a
adb shell dd if=/sdcard/abl.img of=/dev/block/bootdevice/by-name/abl_b
adb push cmnlib.img /sdcard/cmnlib.img
adb shell dd if=/sdcard/cmnlib.img of=/dev/block/bootdevice/by-name/cmnlib_a
adb shell dd if=/sdcard/cmnlib.img of=/dev/block/bootdevice/by-name/cmnlib_b
adb push cmnlib64.img /sdcard/cmnlib64.img
adb shell dd if=/sdcard/cmnlib64.img of=/dev/block/bootdevice/by-name/cmnlib64_a
adb shell dd if=/sdcard/cmnlib64.img of=/dev/block/bootdevice/by-name/cmnlib64_b
adb push devcfg.img /sdcard/devcfg.img
adb shell dd if=/sdcard/devcfg.img of=/dev/block/bootdevice/by-name/devcfg_a
adb shell dd if=/sdcard/devcfg.img of=/dev/block/bootdevice/by-name/devcfg_b
adb push hyp.img /sdcard/hyp.img
adb shell dd if=/sdcard/hyp.img of=/dev/block/bootdevice/by-name/hyp_a
adb shell dd if=/sdcard/hyp.img of=/dev/block/bootdevice/by-name/hyp_b
adb push keymaster.img /sdcard/keymaster.img
adb shell dd if=/sdcard/keymaster.img of=/dev/block/bootdevice/by-name/keymaster_a
adb shell dd if=/sdcard/keymaster.img of=/dev/block/bootdevice/by-name/keymaster_b
adb push xbl.img /sdcard/xbl.img
adb shell dd if=/sdcard/xbl.img of=/dev/block/bootdevice/by-name/xbl_a
adb shell dd if=/sdcard/xbl.img of=/dev/block/bootdevice/by-name/xbl_b
adb push xbl_config.img /sdcard/xbl_config.img
adb shell dd if=/sdcard/xbl_config.img of=/dev/block/bootdevice/by-name/xbl_config_a
adb shell dd if=/sdcard/xbl_config.img of=/dev/block/bootdevice/by-name/xbl_config_b
REMEMBER
"Invalid sparce file format at header magic" is not an error, you need to wait a bit when you see that string, just wait.
These ROMs can't be used to update or downgrade your phone but just to restore your phone, so don't use them to come back to oreo or to update from oreo to pie.
If you want to rebrand your phone from HydrogenOS to OxygenOS you can follow this guide: Rebrand Guide
If you want you can use also my tool to flash Factory Images, unlock bootloader, flash twrp or to understand if the device is recognized: https://toolaio.tk/
Thanks to @SaiBork for first time tested
If you got some problems like write error or no partition, check this: https://forum.xda-developers.com/showpost.php?p=76658555&postcount=34
Thanks to @Dark Nightmare for T-Mobile Rom Version
DONATE LINK
If you want to support this and others my projects please consider making a donation, thanks.
If you are unable to use pools or moneybox, you can also make a normal donation, all private donations will be added in the moneybox:
Thanks Mister :good:
Great work, thx
This is great work. Thanks!
If anyone has the T-Mobile firmware or OTA captured, please post it.
Would it be wise to extract the zip to the 6T prior to rooting just in case something goes wrong?
shizat63 said:
Would it be wise to extract the zip to the 6T prior to rooting just in case something goes wrong?
Click to expand...
Click to collapse
This fastboot rom are completely stock rom, not modified
mauronofrio said:
This fastboot rom are completely stock rom, not modified
Click to expand...
Click to collapse
Right.
So before rooting the device, would it be good to copy the images from this zip to a dir on the 6T in case something goes wrong with the rooting process? For example if Magisk or TWRP mess something up, and the 6T is in a bootloop.
Or are the images in the zip only for flashing from your PC to the 6T? So it would be of no use to have the images sitting on the 6T as a backup.
Hello. after flashing with flash-all.bat, my 6T just boots to the bootloader unlocked warning and stays there. I don't know what to do next.
EDIT: Nevermind, after trying again it worked.
shizat63 said:
Right.
So before rooting the device, would it be good to copy the images from this zip to a dir on the 6T in case something goes wrong with the rooting process? For example if Magisk or TWRP mess something up, and the 6T is in a bootloop.
Or are the images in the zip only for flashing from your PC to the 6T? So it would be of no use to have the images sitting on the 6T as a backup.
Click to expand...
Click to collapse
Actually there is not a twrp that support decryption so if you also have the images on the phone you can't flash it in twrp mode. At this moment these roms can be only flashed through fastboot with a pc
Seoyoon said:
Hello. after flashing with flash-all.bat, my 6T just boots to the bootloader unlocked warning and stays there. I don't know what to do next.
EDIT: Nevermind, after trying again it worked.
Click to expand...
Click to collapse
Perfect:good:
thank you thank you thank you OP! Nearly bricked my phone while trying to install root (something got messed up with TWRP) and I couldn't even get out of bootloader into recovery. I just got my phone a few hours ago, that would have been sad
nhshah7 said:
thank you thank you thank you OP! Nearly bricked my phone while trying to install root (something got messed up with TWRP) and I couldn't even get out of bootloader into recovery. I just got my phone a few hours ago, that would have been sad
Click to expand...
Click to collapse
Perfect:good:
If you want to support this and others my projects please consider making a donation, thanks.
After using flash-all.bat I'm getting the "Your device is corrupt" red error message on boot. I can skip by pressing power twice and phone boots normally.
I see people with 6 had to use MSM download tool to get rid of the error.
Is there any solution for 6T?
nhshah7 said:
thank you thank you thank you OP! Nearly bricked my phone while trying to install root (something got messed up with TWRP) and I couldn't even get out of bootloader into recovery. I just got my phone a few hours ago, that would have been sad
Click to expand...
Click to collapse
Just for the sake of your sanity in the future, if you can get to bootloader and device files are available, you can always get it up and running. I learned that very quickly way back in the day
iaTa said:
After using flash-all.bat I'm getting the "Your device is corrupt" red error message on boot. I can skip by pressing power twice and phone boots normally.
I see people with 6 had to use MSM download tool to get rid of the error.
Is there any solution for 6T?
Click to expand...
Click to collapse
Only msm tool i think
Well same situation here got boot loop trying to root then after install using flashall.bat now I can't get a VOLTE and now I complete lost signal but when I swap my sim card to sim slot 2 everything work...kinda weir but does anyone know how to fix it?
_BГ@ckθut said:
Well same situation here got boot loop trying to root then after install using flashall.bat now I can't get a VOLTE and now I complete lost signal but when I swap my sim card to sim slot 2 everything work...kinda weir but does anyone know how to fix it?
Click to expand...
Click to collapse
Did you have a branded version?
mauronofrio said:
Did you have a branded version?
Click to expand...
Click to collapse
Oh I has unlock one from on plus website and use it on Verizon...is that what u mean...sorry I'm new to OP device
Edit: I try to do fastboot flash modem A and B also factory reset but seem not work...
_BГ@ckθut said:
Oh I has unlock one from on plus website and use it on Verizon...is that what u mean...sorry I'm new to OP device
Click to expand...
Click to collapse
Branded version are different, they have a particoular partitions for volte, i think the only.method to solve your problem is to find another person with the same branded device and make a partitions backup that you can restore
mauronofrio said:
Branded version are different, they have a particoular partitions for volte, i think the only.method to solve your problem is to find another person with the same branded device and make a partitions backup that you can restore
Click to expand...
Click to collapse
So how do I make that? Do I need provide any information or anything?
When i try to boot into fastboot mode using power key and volume - key, it shows me a blank screen :crying::crying: . there is no bunny with fastboot logo. only black screen.anyone help me please.
Note: I am on pie with march update.
feroz mahmud said:
...there is no bunny with fastboot logo. only black screen....Note: I am on pie with march update.
Click to expand...
Click to collapse
Maybe you still get into fastboot mode, but screen is black due to corrupted splash partition? You can check that subj is in bootloader mode using "fastboot devices -l" from PC. If yes, you can reflash splash.img from 10.0.2.0 fastboot image.
Aerobatic said:
Maybe you still get into fastboot mode, but screen is black due to corrupted splash partition? You can check that subj is in bootloader mode using "fastboot devices -l" from PC. If yes, you can reflash splash.img from 10.0.2.0 fastboot image.
Click to expand...
Click to collapse
Will you please tell me the process of flashing splash? And where do i get this file?
feroz mahmud said:
Will you please tell me the process of flashing splash? And where do i get this file?
Click to expand...
Click to collapse
Same as all other flashing via fastboot.
The only official fastboot image for Mi A2 AO Pie available yet is v10.0.2.0 PDIMIFJ and can be found at http://en.miui.com/download-353.html or https://forum.xda-developers.com/mi-a2/how-to/fastboot-xiaomi-mi-a2-fastboot-images-t3824849.. Here in forum you can find hand-made variants of images for 10.0.3.0-10.0.7.0, but all these contain same image of splash partition as in official ROM (if any).
.TGZ and .TAR archives can be unpacked by 7z and many other programs.
Inside archive is directory called smth like "jasmine_global_images_V10.0.2.0.PDIMIFJ_9.0" containing the ready ROM image for fastboot flash.
Inside this directory there are several batch files, containing the same line for flashing splash partition:
Code:
fastboot flash splash %~dp0images\splash.img
Note that "splash.img" is foind in " \Images" subdirectory.
So, you will need:
1. Mi A2 with unlocked bootloader and critical partitions (search this forum on how to unlock) in bootloader mode, connected to USB 2.0 port in PC;
2. Working drivers and / ADB / fastboot installation.
3. "splash.img" copied into directory of working ADB / fastboot installation.
To check that requirement (1) and (2) are fulfilled, run CMD shell in directory of working ADB / fastboot installation and type
Code:
fastboot devices
If output list contains the only 1 string with ID of device (same as shown by "ADB devices -l" command in normal MTP file transfer mode), you are ready to type in commands:
Code:
fastboot flash splash .\splash.img
fastboot reboot bootloader
You are supposed to see the 'bunny' after phone reboots to bootloader mode once again. To reboot back to system just use "fastboot reboot"
If above is not helpful, bring phone to service
Aerobatic said:
Same as all other flashing via fastboot.
The only official fastboot image for Mi A2 AO Pie available yet is v10.0.2.0 PDIMIFJ and can be found at http://en.miui.com/download-353.html or https://forum.xda-developers.com/mi-a2/how-to/fastboot-xiaomi-mi-a2-fastboot-images-t3824849.. Here in forum you can find hand-made variants of images for 10.0.3.0-10.0.7.0, but all these contain same image of splash partition as in official ROM (if any).
.TGZ and .TAR archives can be unpacked by 7z and many other programs.
Inside archive is directory called smth like "jasmine_global_images_V10.0.2.0.PDIMIFJ_9.0" containing the ready ROM image for fastboot flash.
Inside this directory there are several batch files, containing the same line for flashing splash partition:
Code:
fastboot flash splash %~dp0images\splash.img
Note that "splash.img" is foind in " \Images" subdirectory.
Click to expand...
Click to collapse
thanks for you information. my device is locked. when i try to peform fastboot devices , it shows me a error saying application was unable to start correctly.
1. Search for guides how to install ADB drivers and use fastboot, and study these
2. Search here for guides how to unlock bootloader and critical of Mi A2
Nobody will move your fingers except you.
Aerobatic said:
1. Search for guides how to install ADB drivers and use fastboot, and study these
2. Search here for guides how to unlock bootloader and critical of Mi A2
Nobody will move your fingers except you.
Click to expand...
Click to collapse
thanks for your information.
My devices is locked(bootloader). and fastboot isn't showing up. now tell me how do i flash spalsh file?
1. Is phone working and the only problem is black screen in fastboot mode?
If phone is bricked, just bring it to service or somebody who knows what to do.
Following is what you could have already found in guides I was suggesting to find and study
2. Prepare everything for unlocking in phone:
2.1. Get "developer rights"
2.2 Allow "USB debugging" and "OEM unlocking" in developer options
3. Have you get acquainted with ADB drivers installation and ADB commands and fastboot commands?
Can you see result of "adb devices -l" command in CMD shell when phone is attached to USB-2.0 port with MTP file transfer enabled?
If no, just bring it to service or somebody who knows what to do.
4. Can you see result of "fastboot devices -l" command in CMD shell when phone is attached to USB-2.0 port in what is supposed to be bootloader mode with black screen?
If no, just bring it to service or somebody who knows what to do.
5.. If yes, and device ID is the same as in result of "adb devices -l" command
6. Unlock bootloader and critical (see guides here in Mi A2 threads), it takes 2 commands and 2 reboots
7. Reflash splash.img as stated above in my 1st message
Nobody here can repair your phone, - only you or service. So I won't write more here.
Aerobatic said:
1. Is phone working and the only problem is black screen in fastboot mode?
If phone is bricked, just bring it to service or somebody who knows what to do.
.
Click to expand...
Click to collapse
Can you help me with this? my phone is ok, when i run fastboot command it shows me "??????????? fastboot"
Restart pc or update adb and drivers.
I submitted on ( in deep tool ) still application approved
Can I open bootloader now ?
I need rom for my device and all file to root it
V ( RMX3241_11_A.15 )
do you still want to root smartphone?
Please don't root , useless as no custom ROM is available or you might brick your device
I have rooted my smartphone, on realme 8 5G
Rzk09 said:
I have rooted my smartphone, on realme 8 5G
Click to expand...
Click to collapse
Hello, can you tell me how you got root access, thanks
frenon76 said:
Hello, can you tell me how you got root access, thanks
Click to expand...
Click to collapse
has your device been unlocked bootloader?
Not yet, I'm working on it
frenon76 said:
Not yet, I'm working on it
Click to expand...
Click to collapse
what version of the firmware build is on your device?
RMX3241VF_11_A_23
frenon76 said:
RMX3241VF_11_A_23
Click to expand...
Click to collapse
Global or India?
Global
frenon76 said:
Global
Click to expand...
Click to collapse
if you have unlocked your device, follow these steps
1.donwload boot.img and vbmeta.img, if your firmware version is A.23 global version you can download it in Attachments
2. Patch the boot.img that you downloaded earlier in the magisk manager, when it's finished you can change the name to "boot.img" to make it easier to patch
3. Copy the boot.img patch to your laptop/PC in "adb and fastboot" folder, together with vbmeta.img (don't patch the vbmeta.img file in magisk manager)
4. turn on usb debugging option
5. enter fastboot mode (turn off your device and hold vol up and power)
6. if you have entered fastboot, plug your devices into your laptop/pc and type in adb "fastboot devices" (make sure your devices are connected)
7. And now start patching the boot.img file that you patched earlier and disable boot verification (vbmeta.img)
8. Ok,Patch the boot.img file with the command "fastboot flash boot boot.img"
9. and finally disable vbmeta copy this command "fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img"
10. and restart your device
I hope this can help you
Muchas gracias, voy a intentar
Rzk09 said:
if you have unlocked your device, follow these steps
1.donwload boot.img and vbmeta.img, if your firmware version is A.23 global version you can download it in Attachments
2. Patch the boot.img that you downloaded earlier in the magisk manager, when it's finished you can change the name to "boot.img" to make it easier to patch
3. Copy the boot.img patch to your laptop/PC in "adb and fastboot" folder, together with vbmeta.img (don't patch the vbmeta.img file in magisk manager)
4. turn on usb debugging option
5. enter fastboot mode (turn off your device and hold vol up and power)
6. if you have entered fastboot, plug your devices into your laptop/pc and type in adb "fastboot devices" (make sure your devices are connected)
7. And now start patching the boot.img file that you patched earlier and disable boot verification (vbmeta.img)
8. Ok,Patch the boot.img file with the command "fastboot flash boot boot.img"
9. and finally disable vbmeta copy this command "fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img"
10. and restart your device
I hope this can help you
Click to expand...
Click to collapse
HELP, I did this on my phone (realme 8 5g global) and now the system does not turn on as something is recovery (TWRP) and fastboot works normally
this is my main and the only relatively new phone so please help
PS sorry for mistakes, I'm from Poland and I'm writing through a translator
Rzk09 said:
if you have unlocked your device, follow these steps
1.donwload boot.img and vbmeta.img, if your firmware version is A.23 global version you can download it in Attachments
2. Patch the boot.img that you downloaded earlier in the magisk manager, when it's finished you can change the name to "boot.img" to make it easier to patch
3. Copy the boot.img patch to your laptop/PC in "adb and fastboot" folder, together with vbmeta.img (don't patch the vbmeta.img file in magisk manager)
4. turn on usb debugging option
5. enter fastboot mode (turn off your device and hold vol up and power)
6. if you have entered fastboot, plug your devices into your laptop/pc and type in adb "fastboot devices" (make sure your devices are connected)
7. And now start patching the boot.img file that you patched earlier and disable boot verification (vbmeta.img)
8. Ok,Patch the boot.img file with the command "fastboot flash boot boot.img"
9. and finally disable vbmeta copy this command "fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img"
10. and restart your device
I hope this can help you
Click to expand...
Click to collapse
bro please i need your help i'am on A24 Global version version do u have boot.img of this version if not please give me link of A23 global version full rom thank u
mantap, how to downgrade into RMX3241VF_11_A_23? ada no wa or youtube or ig?.. thank u, terima kasih
Rzk09 said:
I have rooted my smartphone, on realme 8 5G
Click to expand...
Click to collapse
Vbmat.img and boot.img for RMX3241_11_A.16 please
Rzk09 said:
if you have unlocked your device, follow these steps
1.donwload boot.img and vbmeta.img, if your firmware version is A.23 global version you can download it in Attachments
2. Patch the boot.img that you downloaded earlier in the magisk manager, when it's finished you can change the name to "boot.img" to make it easier to patch
3. Copy the boot.img patch to your laptop/PC in "adb and fastboot" folder, together with vbmeta.img (don't patch the vbmeta.img file in magisk manager)
4. turn on usb debugging option
5. enter fastboot mode (turn off your device and hold vol up and power)
6. if you have entered fastboot, plug your devices into your laptop/pc and type in adb "fastboot devices" (make sure your devices are connected)
7. And now start patching the boot.img file that you patched earlier and disable boot verification (vbmeta.img)
8. Ok,Patch the boot.img file with the command "fastboot flash boot boot.img"
9. and finally disable vbmeta copy this command "fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img"
10. and restart your device
I hope this can help you
Click to expand...
Click to collapse
Can you send me the attachments for RMX3241_11_C.04 this android version?
Rooted Realme 8 5G to fix unknown IMEI but in the end I know that unknown baseband is the major problem, and no custom ROM for RMX3241.
Stock firmware: RMX3241_11_A.26
Magisk 25.2
Root Tool: MTKClient (GitHub) with Brom/Edl Mode since I got no fastboot
For MTKClient, you'll need to install "MediaTek CDC driver 1.0.8" and manually add legacy hardware in device manager "MediaTek USB PORT" and other thing that you need in the github link.
Root method just same as fastboot method, patch your boot.img with Magisk app and flash patched boot.img + vbmeta.img or using MTKClient flash the patched boot.img and vbmeta.img.empty included in MTKClient.
Where to get your stock boot.img vbmeta.img? Use MTKClient or MTKMETAUTILITY to dump it from your phone. Dump the whole img except userdata to backup just incase....
If somehow the root fail after like 1h bootloop at logo, just reflash with stock boot vbmeta. So keep in mind to backup your stock img file.
I also have TWRP as recovery flashed using MTKClient but no custom ROM?
Hi, first of all, I'm not a dev or else just user who had difficulties to flash GSI on my phone... Was 7 years with a samsung galaxy Note 3, with twrp....So easy to flash....
with the help of @gr0ndpa, thanks to him.....
FLASH GSI
Now I will explain how to flash easily with files attached
1/ first of all you need a phone and drivers installed, use xiaomi pc suite, unzip and install it
2/ you need to activate USB debug in dev options.
3/ dl platform tools folder unzip it and put in C
4/ run command and type
Code:
cd /adb
5/ then
Code:
adb devices
to check if phone recognised
6/
Code:
adb reboot bootloader
once in fast boot
7/
Code:
fastboot flash vbmeta vbmeta.img
wait finished type to enter in fastbootD
8/
Code:
fastboot reboot fastboot
9/
Code:
fastboot flash system
LiR 313.XXX.img
you will have a system error, but wait the flash begin in few seconds
at the end wait ok then
10/
Code:
fastboot reboot recovery
on stock recover
11/ wipe data and reboot with +/- and PWR
and you're done...
In case you want to flash custom kernel or patched boot image to root with magisk, you have to
12/
Code:
adb reboot bootloader
Copy kernel boot image to C drive and rename kernel boot image to boot.img.
13/
Code:
fastboot flash boot c:\boot.img
14/
Code:
fastboot reboot
In case you want to flash twrp put the file to adb folder and type in fastboot
15/
Code:
fastboot boot twrp.img
You can check what I ve done on tuto ss...
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++==================================================================================================================================================================================================================++
Flash ROM
This now how to flash ROM on your device, it's convenient for all roms like LOS, corvus, awaken...
First you need all the proper drivers installed and unlocked bootloader, USB debugging all of that stuff.
Now open up a cmd/terminal , and put the files i sent and the ROM file in the folder from where you're opening the cmd/terminal and connect the phone (you may need to put ./ as an suffix for all the commands if you're on linux)
Type
Code:
adb reboot bootloader
Then type
Code:
fastboot devices
to see if everything is ok
Then type
Code:
fastboot flash boot_ab boot.img
(you can drag and drop the file instead of typing it)
After that's done type
Code:
fastboot flash vendor_boot_ab vendor_boot.img
(you can drag and drop this too if you want)
Code:
fastboot flash dtbo dtbo.img
(you can drag and drop this too if you want)
After that's done type
Code:
fastboot reboot recovery
This will boot you into a recovery and now you need to go to wipe and format data
After that go to apply update then adb sideload then
In the cmd type
Code:
adb sideload rom.zip
for example (you put the ROM zip here you can drag and drop it)
Wait for that to finish it will go to 47% and on the phone it will show step 1/2 then step 2/2
and when it's done it's gonna show an error
adb: failed to read command: No error
Then you can reboot to system
One more
Two more
This the tuto I follow to flash renoir, who have same characteristic than all Note 12 series... Tuesday I can confirm it works
I'm having a problem that my phone can't go to fastboot via CMD after I flash vbmeta.
Is is me doing wrong or also happen to you?